AT HOME HARD GOODS PERFORMANCE SPECIFICATION SEPTEMBER 2013
NPG Supplier Procedures Manual © 2014 Nordstrom, Inc., all rights reserved. CONFIDENTIAL: These documents contain proprietary, trade secret, and confidential information which are the property of Nordstrom, Inc. These documents and their contents may not be duplicated or
disclosed to any other party without express authorization of Nordstrom, Inc. Page 1 of 28
HARD GOODS PERFORMANCE SPECIFICATIONS
NPS-G8 Ceramic & Glass Tableware
NPS-G10 Candle and Candleholder / Accessories
NPS-G12 Picture Frame
NPS-G15 Seasonal Decoration / Figurine / Vase/ Ornaments
NPS-G16 Incense / Aroma Oil / Infusers
NPS-G17 Water Globes
NPS G22 Small End Table, Side Table
NPS-G25 Holiday Stockings
NPS-G28 Beaded Garland
NPS G30 Sofa and Chair (Upholstered Indoor/Outdoor)
NPS-G31 Mirror
NPS-G39 Photo Album / Scrapbook
NPS-G43 Wooden Items ( Wooden Bowl, Serving Tray )
AT HOME HARD GOODS PERFORMANCE SPECIFICATION SEPTEMBER 2013
NPG Supplier Procedures Manual © 2014 Nordstrom, Inc., all rights reserved. CONFIDENTIAL: These documents contain proprietary, trade secret, and confidential information which are the property of Nordstrom, Inc. These documents and their contents may not be duplicated or
disclosed to any other party without express authorization of Nordstrom, Inc. Page 2 of 28
CERAMIC TABLEWARE
Flatware, Mugs, Pitchers, Utensils, Decaled, Glazed, Molded GLASS
Flatware, Mugs, Pitcher, Hand blown, Molded, Clear, Colored
NPS-G8 (Page 1 of 2)
TEST PROPERTY TEST METHODS TEST REQUIREMENTS *CA PROP 65 CONSENT JUDGMENT OF RELATED COURT CASE BASED ON CALIFORNIA PROPOSITION 65
Labeling
Use Labeling (If applicable)
VISUAL Use/care instructions that are clear and understandable shall be provided in language appropriate to destination countries.
Cautionary Statements (If applicable)
VISUAL Provides cautionary labeling as appropriate in languages of countries of distribution.
Verify Label Claims VISUAL Must comply with all claims (Microwaveable, dishwasher safe etc.)
Labeling- Packaging -Fair Packaging & Labeling
Act 16 CFR 500
-Consumer Packaging & Labeling Act- R.S. 1985. c C-38 , C.R.C., c. 147
Must comply with all US and Canadian requirements. -Manufacturer, Packaging or distributors Name & Address - Product Identification - Net Quantity of Contents - Dimensions (English & Metric) - Finished Size (English & Metric)
Country of Origin Marking
-US 19 CFR 134.11 -Canada Customs Tariff, Marking of Imported Goods Regulations, SOR-94-1 10
Must comply with all US and Canadian regulations
Analytical
Leachable Lead & Cadmium (for food use only)
FDA CPG 7117.06 & 7117.07
ASTM C738
A.O.A.C. Official Methods of Analysis 18th Edition (2005) Method 973.32 Canada Consumer Product Safety Act, Glazed Ceramics and Glassware Regulations
Must comply with all US FDA & Prop 65 and Canada regulations The most stringent standard is used
Lead Cadmium
Flatware < 0.226 ppm < 0.5 ppm
Small Hollowware < 0.100 ppm < 0.189 ppm
Large Hollowware < 0.100 ppm < 0.049 ppm
Cups and Mugs < 0.5 ppm < 0.5 ppm
Pitchers < 0.5 ppm < 0.25 ppm
1ppm=1mg/l =1 ug/ml
Lead Content of Paints or Similar Surface Coating
16 CFR 1303 Canada- Consumer Product Safety Act,
Surface Coating Materials Regulations
Must comply with all US and Canadian regulations Shall not exceed 90 ppm (0.009%)
Leachable Lead & Cadmium Lip & Rim (Decorated Glass and Ceramic if the cup/mug is decorated on the top 2 cm or 20 mm)
ASTM C927
Canada Consumer Product Safety Act,
Glazed Ceramics and Glassware Regulations
Must comply with all US and Canadian regulations The most stringent standard is used Lead and Cadmium extracted from lip and rim area.
Lead Cadmium
Lip & Rim Area ≤ 0.5 ppm ≤ 0.4 ppm
Physical Characteristics
Total Weight (lbs) Standard Measurement Within 3% tolerance of labeled weight
Diameter (inches) Standard Measurement Within 3% tolerance of labeled dimensions
Capacity ( if applicable) Standard Measurement 0%/+3% (tolerance of claim)
Workmanship Visual No Major Defects.
Sharp Edge 16 CFR 1500.49 (Modified)
No sharp edge.
Sharp Point 16 CFR 1500.48 (Modified)
No sharp point.
Stability Visual No tipping over when placed on the flat-leveled surface.
THE AGENT/ MANUFACTURER IS RESPONSIBLE TO ENSURE THAT THE REFERENCED STYLE CONFORMS TO ALL
THE PERFORMANCE REQUIREMENTS LISTED ON THIS SPECIFICATION
AT HOME HARD GOODS PERFORMANCE SPECIFICATION SEPTEMBER 2013
NPG Supplier Procedures Manual © 2014 Nordstrom, Inc., all rights reserved. CONFIDENTIAL: These documents contain proprietary, trade secret, and confidential information which are the property of Nordstrom, Inc. These documents and their contents may not be duplicated or
disclosed to any other party without express authorization of Nordstrom, Inc. Page 3 of 28
CERAMIC TABLEWARE (CONTINUED)
Flatware, Mugs, Pitchers, Utensils, Decaled, Glazed, Molded GLASS
Flatware, Mugs, Pitcher, Hand blown, Molded, Clear, Colored
NPS-G8 (Page 1 of 2)
TEST PROPERTY TEST METHODS TEST REQUIREMENTS
Performance
Impact Resistance ASTM C368 Modified No major defects.
Lid Fitting Standard Measure Lid should fit securely.
Thermal Shock Intertek Method 1hour@ 350F to room temperature in water without cracking or deformation.
Microwave Oven Safe (If claimed)
Intertek Method Satisfactory Fill with water, Heat item separately in 750watt microwave oven for 5min.@100% power.
Dishwasher Safe (If claimed)
Intertek Method 10 cycles of normal wash with domestic detergent - no breakage or adverse effects.
Freezer Safe (If claimed)
Intertek Method No cracking or deformation Extreme temperature (-15c) for 24 hours
Stain Resistance Intertek Method No staining.
Handle Strength for Lids
Standard Measure 5lb.pull @60sec.
Handle Strength Impact
Intertek Method Minimum 3 in-oz. Impact Force from a distance of 1”@ various angle from the handle.
Resistance to Corrosion (Metal components)
ASTM B117 (Modified)
Withstand 24 hours in 1% salt spray (fog) with no major corrosion or visual change. Modification = 1% salt (fog) spray.
Effect of Humidity (If claimed-Metal only)
Intertek Method No Visual Change after 24hrs. @ 95%RH, 120F.
THE AGENT/ MANUFACTURER IS RESPONSIBLE TO ENSURE THAT THE REFERENCED STYLE CONFORMS TO ALL THE PERFORMANCE REQUIREMENTS LISTED ON THIS SPECIFICATION
AT HOME HARD GOODS PERFORMANCE SPECIFICATION SEPTEMBER 2013
NPG Supplier Procedures Manual © 2014 Nordstrom, Inc., all rights reserved. CONFIDENTIAL: These documents contain proprietary, trade secret, and confidential information which are the property of Nordstrom, Inc. These documents and their contents may not be duplicated or
disclosed to any other party without express authorization of Nordstrom, Inc. Page 4 of 28
CANDLE & CANDLE HOLDER/ ACCESSORIES
NPS-G10 (Page 1 of 4)
TEST PROPERTY TEST METHODS TEST REQUIREMENTS *CA PROP 65 CONSENT JUDGMENT OF RELATED COURT CASE BASED ON CALIFORNIA PROPOSITION 65
Labeling
Use Labeling (If applicable)
VISUAL Use/care instructions that are clear and understandable shall be provided in language appropriate to destination countries.
Labeling- Packaging -Fair Packaging & Labeling
Act (FPLA) 16 CFR 500
-Consumer Packaging & Labeling Act- R.S. 1985. c C-38 , C.R.C., c. 147
Must comply with all US and Canadian requirements. -Manufacturer, Packaging or distributors Name & Address - Product Identification - Net Quantity of Contents - Dimensions (English & Metric) - Finished Size (English & Metric)
Labeling of Candle size
-Fair Packaging & Labeling Act (FPLA)16 CFR 501.7
Tapered candles and irregularly shaped decorative candles, which are either hand dipped or molded, do not need to be labeled with the diameter of the candle. The candles must be labeled with count and length or height in inches to meet the requirements of FPLA.
Candle Requirement
Filled Wax Height Only
Taper/Irregular Height Only
Votive/Circular Height & Diameter
Votive/Irregular Height Only
Pillar/Circular Height & Diameter
Pillar/Square Height & Width
Country of Origin Marking
-19 CFR 134.11 -Canada Customs Tariff, Marking of Imported Goods Regulations, SOR-94-1 10
Must comply with all US and Canadian regulations
Cautionary Labeling
ASTM F2058-07 Candle - All units for sale of candles shall comply with either text-
only option or text- and- pictogram option as shown below.
Candle holder -
To prevent fire use with a (specify size/type of Candle) candle. Never leave burning candle unattended. Keep out
of the reach of children And pets. Never burn candle on or near anything that can catch fire. Trim wick to ¼ inch prior to lighting. Do not allow wick Trimming to accumulate in wax pool. Place on temperature safe surface. Must meet the minimum size requirements and provide the Above minimum safety language and safety alert symbol. Also must include the following for specific candle types: Filled candle: “container will be hot when candle is lit”
THE AGENT/ MANUFACTURER IS RESPONSIBLE TO ENSURE THAT THE REFERENCED STYLE CONFORMS TO ALL THE PERFORMANCE REQUIREMENTS LISTED ON THIS SPECIFICATION
AT HOME HARD GOODS PERFORMANCE SPECIFICATION SEPTEMBER 2013
NPG Supplier Procedures Manual © 2014 Nordstrom, Inc., all rights reserved. CONFIDENTIAL: These documents contain proprietary, trade secret, and confidential information which are the property of Nordstrom, Inc. These documents and their contents may not be duplicated or
disclosed to any other party without express authorization of Nordstrom, Inc. Page 5 of 28
CANDLE & CANDLE HOLDER/ ACCESSORIES (CONTINUED)
NPS-G10 (Page 2 of 4)
TEST PROPERTY TEST METHODS TEST REQUIREMENTS
Labeling (Cont)
Non-food Use Warnings – For ceramic ware only if truly decorative or ornamental and could be used with food; as an alternative to meeting lead standards
21 CFR 109.6 State the following: • “Not for Food Use. May Poison Food.” This message must be present in two forms: 1. A stick-on label must be on the surface that is clearly visible to
the consumer. 2. A conspicuous and legible permanent statement that is on the exterior surface of the base of the ceramic ware. The letters shall be at least 3.2 millimeters (0.125 inch) in height or as provided in the regulation.
EPA Registration / FIFRA 25(B)Exemption
EPA/FIFRA Vendor must provide proof of EPA registration or proof of state registration according to FIFRA. Lab will review documentation.
Analytical
Lead In Surface Coating 16 CFR 1303 Canada Consumer Product Safety Act, Surface Coating Materials Regulations
Shall not exceed 90 ppm (0.009% by weight) total lead
Lead cored wicks 16 CFR 1500.17(a)(13) No Lead Cored Wicks
Paraffin Content ( only for candles imported from China)
US Customs Laboratory Methods USCL 34-07
Non-novelty candles must not contain paraffin wax.
Physical Characteristics
Workmanship Visual No major defects; one minor defect allowed
Sharp Points/Edges 16 CFR 1500.48/49 Shall have no hazardous sharp points/edges
Weight Of Candle (grams) Standard Measurement Report actual & label claims. -0%/+5% (tolerance of claim)
Weight of Holder/ Accessories (grams)
Standard Measurement Report actual & label claims. -0%/+5% (tolerance of claim)
Dimensions of Candle Standard Measurement Report actual & label claims. -0%/+5% (tolerance of claim)
Dimensions of Holder/ Accessories
Standard Measurement Report actual & label claims. -0%/+5% (tolerance of claim)
Wick Length (In.) Standard Measurement Sufficient length for lighting (min. ¼” exposed wick)
Wick Analysis: A. Shape & Dimensions B. B. Construction,
Type, Defects, Etc.
Visual Report actual Report actual
Aesthetic Evaluation Visual Should be free of bubbles, cracks, chips, or dents except when they are intended as part of the design/pattern.
Performance
Flammability of solids 16 CFR 1500.44 modified
Burn rate <01. In/Sec. All surfaces of each different material on candleholders shall be tested for flammability of solids. (Modification = Test all surfaces of different materials instead of just testing on the major axis) Note: Candles are burned for 8-hour cycles until end of useful life
Flammability of raw material fragrance or liquid – if applicable – gel candles only
16 CFR 1500.43a/ 16 CFR 1500.3(c)(6)
Flashpoint shall be greater than 150°F.
Visual Smoke Visual Smoke is recorded as “Intermittent” or “Continuous”. The total number of readings must not exceed 20% (intermittent) / 10% (continuous) of the total number of hours burned.
Flame Height ASTM 2417-11 Section 4.1
Flame height shall not exceed 3 inches when measured from the base of the flame to the tip of the flame.
Secondary ignition ASTM F2417-11 Section 4.2
Shall not cause secondary ignition, such as igniting material other than the intended wick during candle burning testing.
THE AGENT/ MANUFACTURER IS RESPONSIBLE TO ENSURE THAT THE REFERENCED STYLE CONFORMS TO ALL THE PERFORMANCE REQUIREMENTS LISTED ON THIS SPECIFICATION
AT HOME HARD GOODS PERFORMANCE SPECIFICATION SEPTEMBER 2013
NPG Supplier Procedures Manual © 2014 Nordstrom, Inc., all rights reserved. CONFIDENTIAL: These documents contain proprietary, trade secret, and confidential information which are the property of Nordstrom, Inc. These documents and their contents may not be duplicated or
disclosed to any other party without express authorization of Nordstrom, Inc. Page 6 of 28
CANDLE & CANDLE HOLDER/ ACCESSORIES (CONTINUED)
NPS-G10 (Page 3 of 4)
TEST PROPERTY TEST METHODS TEST REQUIREMENTS
Performance (Cont)
Spontaneous re-ignition
Canadian Proposed Candle Regulation, Section 7
Candle shall not re-ignite spontaneously after being extinguished.
End of useful life ASTM F2417-11 Section 4.3
Shall not break the container, exhibit excessive flame height, Or exhibit secondary ignition prior to end of useful life.
Stability (for free standing candle)
ASTM 2417-11 Section 4.4
Shall not tip over when placed on a minimum 10° incline. Asymmetrical items - rotation around vertical axis is required.
Flammability - Plastic Container (Including Tea light cups)
ASTM F2417-11 Section 4.5
Total burn time 300 seconds and individual burn time 30 seconds.
Surface Temperature During Burning (For Containers and Holders)
ASTM F2417-11 Section 5.2
Surface temperature shall not exceed listed material limits:
- Metal: 125F
- Glass and other materials: 140F
Flammability – abuse test container interior only – filled candles only
ASTM F2417-11 modified/CPSD-HL-09402-MTHD
Internal surface of candleholder only – the flame impingement shall be 5 minutes. Shall not crack or break exposing a sharp point/edge or expose flame to the outside of the holder. Holder damage (non-hazardous) is acceptable.
Burning time Standard Measurement As approval sample – must comply with claims. (report claimed & actual length of burn time in hours)
Burning characteristics/ Abnormalities
ASTM F2417-11 Section 5.2
Report any abnormalities during burn performance testing that may result in property damage and/or be a potential hazard.
Soot build up Visual No visually excessive build up of residue on container walls.
Visible emission ASTM F2326-04 R09 Report actual
Overflow
ASTM F2417-11 Section 5.2
If holder is present, it shall be capable of containing all Candle material throughout burn test. Report any overflow as data and provide image.
Afterglow
RAL-GZ 041 2005 modified / ASTM F2417-11 section 5.2 modified/ CPSD-HL-09401-MTHD
Afterglow of tip shall be less than 60 seconds after flame is extinguished. Report as failure if afterglow lasts more than 60 seconds. If possible, provide a digital image of the afterglow. Modification = Modified afterglow evaluation periods from within 15 seconds of RAL-GZ 041 to within 60 seconds
Smoke after extinguishing RAL-GZ 041 2005 modified / ASTM F2417-11 section 5.2 modified/ CPSD-HL-09401-MTHD
Smoke shall not last longer than 60 seconds after extinguishing. Report failure if smoke last longer than 60 seconds. If possible, provide a digital image of the smoke. Modification = Modified afterglow evaluation periods from within 15 seconds of RAL-GZ 041 to within 60 seconds
Recorder finding (flame height)
ASTM F2417-11 Section 5.2.4.7
Record testing every hour
Thermal shock of glass containers (test 3 pieces) (For glass container, hurricane, plate but not lantern)
ASTM F2179-02 R07 section 4.2
Determine the cold water bath temperature based on the available tap water temperature and adjust the temperature of the hot water bath to be 90°F higher than the cold water. Once the temperature of the hot water bath has been established, place the samples in the hot water bath for 5 minutes. Remove the samples from the hot water bath and place them into the cold water bath with a time lapse of no more than 15 seconds. Be sure to empty the hot water of the sample containers. Maintain the samples in the cold water bath for 30 seconds. Dry the containers and visually inspect for fractures. Report findings. Any cracking or fractures is considered a failure.
THE AGENT/ MANUFACTURER IS RESPONSIBLE TO ENSURE THAT THE REFERENCED STYLE CONFORMS TO ALL THE PERFORMANCE REQUIREMENTS LISTED ON THIS SPECIFICATION
AT HOME HARD GOODS PERFORMANCE SPECIFICATION SEPTEMBER 2013
NPG Supplier Procedures Manual © 2014 Nordstrom, Inc., all rights reserved. CONFIDENTIAL: These documents contain proprietary, trade secret, and confidential information which are the property of Nordstrom, Inc. These documents and their contents may not be duplicated or
disclosed to any other party without express authorization of Nordstrom, Inc. Page 7 of 28
CANDLE & CANDLE HOLDER/ ACCESSORIES (CONTINUED)
NPS-G10 (Page 4 of 4)
TEST PROPERTY TEST METHODS TEST REQUIREMENTS
For Candle Holder & Accessories
Stability
ASTM F2601-12 Section 4.4
The candle accessory which was fitted with appropriate candle shall not tip over when placed on a minimum 10° incline. Note 1: Candle accessory means object designed, intended, or marketed for use with a candle. Note 2: Use taper candle of 12 in. or more, or pillar candle of 3 in. x 9 in. (Or with the diameter that fits the accessory) if no claim.
Flammability of Candle Ring (3 trials per component)
ASTM F2601-12 Section 4.1
Individual burn time 60s and
Average burn time 30s If the candle ring fail the test, and it is intended for use with candle systems that provide a barrier designed to keep the candle flame from coming in contact with the candle ring, the following warning label shall be affixed to the product:
WARNING
FLAMMABLE. Use this candle ring only with a glass, metal, or ceramic container, or other flame-resistant barrier, between the flame source and the ring. Ring may catch fire when used with a lit candle or near an open flame.
Performance test for candle burners and potpourri burners (test 3 pieces for 1 cycle)
ASTM F2601-12 Section 4.3 (Mod.)
1. No secondary ignition
2. Flame height 1.18 in. (30mm) 3. No end-of-useful life problems as described in ASTM F2417 4. No flare up Note: Each burner have to be tested for a total of 8 burn cycles using scented tea lights.
Moisture Content (Wood items only)
ASTM D4442 Method B(Modified)
Shall be 8-12%
Resistance to Corrosion (Metal components only)
ASTM B117 (Modified)
Withstand 24 hours in 1% salt spray (fog) with no corrosion or visual change.
Effect of Humidity Intertek Method (M0006)
No major corrosion or visual change after 24 hrs. @95%RH, 120F
THE AGENT/ MANUFACTURER IS RESPONSIBLE TO ENSURE THAT THE REFERENCED STYLE CONFORMS TO ALL THE PERFORMANCE REQUIREMENTS LISTED ON THIS SPECIFICATION
AT HOME HARD GOODS PERFORMANCE SPECIFICATION SEPTEMBER 2013
NPG Supplier Procedures Manual © 2014 Nordstrom, Inc., all rights reserved. CONFIDENTIAL: These documents contain proprietary, trade secret, and confidential information which are the property of Nordstrom, Inc. These documents and their contents may not be duplicated or
disclosed to any other party without express authorization of Nordstrom, Inc. Page 8 of 28
PICTURE FRAMES
NPS-G12 (Page 1 of 2)
TEST PROPERTY TEST METHODS TEST REQUIREMENTS *CA PROP 65 CONSENT JUDGMENT OF RELATED COURT CASE BASED ON CALIFORNIA PROPOSITION 65
Labeling
Labeling- Packaging -Fair Packaging &
Labeling Act 16 CFR 500
-Consumer Packaging & Labeling Act- R.S. 1985. c C-38 , C.R.C., c. 147
Must comply with all US and Canadian requirements. -Manufacturer, Packaging or distributors Name & Address - Product Identification - Net Quantity of Contents - Dimensions (English & Metric) - Finished Size (English & Metric)
Country of Origin Marking -19 CFR 134.11 -Canada Customs Tariff, Marking of Imported Goods Regulations, SOR-94-1 10
Must comply with all US and Canadian regulations
Analytical
Lead In Surface Coating 16 CFR 1303 Canada Consumer Product Safety Act, Surface Coating Materials Regulations
Shall not exceed 90 ppm (0.009% by weight) total lead
California Air Resource Board (CARB) Formaldehyde Emissions from Composite Wood Products (Document Review) For wood products only
Airborne Toxic Control Measure(ATCM) California Code of Regulations Title 17,§93120 / ASTM D 6007
The covered products include finished goods composed of or containing: - Particleboard (PB); - Medium Density Fiberboard (MDF); - Thin MDF (≤8 mm in thickness); - Hardwood Plywood (HWPW) made with a composite core (veneer or composite). 1. It is the responsibilities of the manufacturers to maintain chain of custody documentation certifying materials meet CARB requirements. The documentation shall be retained for two years and readily accessible upon request. 2. The label include the fabricator's name, the date the finished good was produced and a marking to denote that the product was made with WPW, PB, or MDF that complies with the applicable Phase 1 or Phase 2 emission standards in section 93120.2(a). Finished goods shall be labeled as having been made with no-added formaldehyde based resins or ULEF resins if this is so for all HWPW, PB, or MDF used in fabricating the finished goods. 3. Document review of the following items are performed at additional charge: a. Mill's Certificate by CARB TPC b. Certificate on wooden panel used c. Labeling on the product
Physical Characteristics
Dimension (in & cm) Standard Measure -0/+5% tolerance of labeled dimensions
Weight (grams) Standard Measure -0/+5%
Workmanship Visual No Major Defects.
Sharp Edge 16 CFR 1500.49 (Modified)
No sharp edge.
Sharp Point 16 CFR 1500.48 (Modified)
No sharp point.
THE AGENT/ MANUFACTURER IS RESPONSIBLE TO ENSURE THAT THE REFERENCED STYLE CONFORMS TO ALL THE PERFORMANCE REQUIREMENTS LISTED ON THIS SPECIFICATION
AT HOME HARD GOODS PERFORMANCE SPECIFICATION SEPTEMBER 2013
NPG Supplier Procedures Manual © 2014 Nordstrom, Inc., all rights reserved. CONFIDENTIAL: These documents contain proprietary, trade secret, and confidential information which are the property of Nordstrom, Inc. These documents and their contents may not be duplicated or
disclosed to any other party without express authorization of Nordstrom, Inc. Page 9 of 28
PICTURE FRAMES (CONTINUED)
NPS-G12 (Page 1 of 2)
TEST PROPERTY TEST METHODS TEST REQUIREMENTS
Performance
Drop Test (non-fragile item only)
ASTM F963-11 (Modified) No breakage 1 times @ 3.0 feet
Resistance to Corrosion (Metal components)
ASTM B117 (Modified) Withstand 24 hours in 1% salt spray (fog) with no major corrosion or visual change. Modification = 1% salt (fog) spray.
Moisture Content (Wood only)
ASTM D4442 - 07 Method B (Modified)
Shall be between 8-12%.
Colorfastness
Crocking (Leather and Textiles)
AATCC 8/116
Dry Wet
Leather Grade 3.0 Grade 1.5
Textiles Grade 4.0 Grade 3.0
Colorfastness to Light (Textiles)
AATCC 16 Option 3
Silk Grade 3.5 @ 10 hours (AFU”S)
Textiles Grade 4.0 @ 20 hours(AFU”S)
THE AGENT/ MANUFACTURER IS RESPONSIBLE TO ENSURE THAT THE REFERENCED STYLE CONFORMS TO ALL THE PERFORMANCE REQUIREMENTS LISTED ON THIS SPECIFICATION
AT HOME HARD GOODS PERFORMANCE SPECIFICATION SEPTEMBER 2013
NPG Supplier Procedures Manual © 2014 Nordstrom, Inc., all rights reserved. CONFIDENTIAL: These documents contain proprietary, trade secret, and confidential information which are the property of Nordstrom, Inc. These documents and their contents may not be duplicated or
disclosed to any other party without express authorization of Nordstrom, Inc. Page 10 of 28
SEASONAL DECORATION / FIGURINE / VASE/ ORNAMENTS
NPS-G15
TEST PROPERTY TEST METHODS TEST REQUIREMENTS *CA PROP 65 CONSENT JUDGMENT OF RELATED COURT CASE BASED ON CALIFORNIA PROPOSITION 65
Labeling
Labeling- Packaging -Fair Packaging &
Labeling Act 16 CFR 500
-Consumer Packaging & Labeling Act- R.S. 1985. c C-38 , C.R.C., c. 147
Must comply with all US and Canadian requirements. -Manufacturer, Packaging or distributors Name & Address - Product Identification - Net Quantity of Contents - Dimensions (English & Metric) - Finished Size (English & Metric)
Country of Origin Marking -19 CFR 134.11 -Canada Customs Tariff, Marking of Imported Goods Regulations, SOR-94-1 10
Must comply with all US and Canadian regulations
California Air Resource Board (CARB) Formaldehyde Emissions from Composite Wood Products (Document Review) For wood products only
Airborne Toxic Control Measure(ATCM) California Code of Regulations
Title 17,§93120 / ASTM D 6007
The covered products include finished goods composed of or containing: - Particleboard (PB); - Medium Density Fiberboard (MDF); - Thin MDF (≤8 mm in thickness); - Hardwood Plywood (HWPW) made with a composite core (veneer or composite). 1. It is the responsibilities of the manufacturers to maintain chain of custody documentation certifying materials meet CARB requirements. The documentation shall be retained for two years and readily accessible upon request. 2. The label include the fabricator's name, the date the finished good was produced and a marking to denote that the product was made with WPW, PB, or MDF that complies with the applicable Phase 1 or Phase 2 emission standards in section 93120.2(a). Finished goods shall be labeled as having been made with no-added formaldehyde based resins or ULEF resins if this is so for all HWPW, PB, or MDF used in fabricating the finished goods. 3. Document review of the following items are performed at additional charge: a. Mill's Certificate by CARB TPC b. Certificate on wooden panel used c. Labeling on the product
Analytical
Lead In Surface Coating 16 CFR 1303 Canada Consumer Product Safety Act, Surface Coating Materials Regulations
Shall not exceed 90 ppm (0.009% by weight) total lead
Physical Characteristics
Workmanship Visual No Major Defects.
Small parts 16 CFR 1501(Modified) Must not create small parts.
Sharp Edge 16 CFR 1500.49(Modified) No accessible Sharp Edge.
Sharp Point 16 CFR 1500.48(Modified) No accessible Sharp Point
Performance
Drop Test (Non-fragile items)
ASTM F963-11 (Modified) 3 times @ 4.5 feet –remains intact and must not create hazard.
Tilt Resistance Intertek Method (M0015) No tipping or instability at 10angle.
Hanging strength (if applicable)
Intertek method Shall withstand 2 times the product weight for 1 hr.
Effects of Humidity Intertek Method (M0006) 24hrs. @ 95 RH 120F – no failure.
Flammability (If applicable) 16 CFR 1500.44 Burn rate 0.1in/sec.
THE AGENT/ MANUFACTURER IS RESPONSIBLE TO ENSURE THAT THE REFERENCED STYLE CONFORMS TO ALL THE PERFORMANCE REQUIREMENTS LISTED ON THIS SPECIFICATION
AT HOME HARD GOODS PERFORMANCE SPECIFICATION SEPTEMBER 2013
NPG Supplier Procedures Manual © 2014 Nordstrom, Inc., all rights reserved. CONFIDENTIAL: These documents contain proprietary, trade secret, and confidential information which are the property of Nordstrom, Inc. These documents and their contents may not be duplicated or
disclosed to any other party without express authorization of Nordstrom, Inc. Page 11 of 28
INCENSE, AROMA OIL & INFUSERS NPS-G16 (page 1 of 2)
TEST PROPERTY TEST METHODS TEST REQUIREMENTS *CA PROP 65 CONSENT JUDGMENT OF RELATED COURT CASE BASED ON CALIFORNIA PROPOSITION 65
Labeling
Labeling- Packaging -Fair Packaging &
Labeling Act 16 CFR 500
-Consumer Packaging & Labeling Act- R.S. 1985. c C-38 , C.R.C., c. 147
Must comply with all US and Canadian requirements. -Manufacturer, Packaging or distributors Name & Address - Product Identification - Net Quantity of Contents - Dimensions (English & Metric) - Finished Size (English & Metric)
Country of Origin Marking -19 CFR 134.11 -Canada Customs Tariff, Marking of Imported Goods Regulations, SOR-94-1 10
Must comply with all US and Canadian regulations
Use labeling Visual check Use care instructions that are clear and understandable; shall be provided in language appropriate to destination countries.
Warning label/first aid instruction
Visual per ASTM 2417 -Must have recommended warning label, “Do not place directly on fine furnishings.” “Keep out of reach of children.” “Do not ingest.” -First aid instruction shall be indicated
Hazard Label Canada Consumer Chemicals and Containers Regulations
Review all applicable requirements for labeling of known hazards of product, including labeling of single use containers if applicable
Verify label claims (additional charges may apply)
Visual check Must comply with all claims. If the product claims to alter mood (i.e. Feel better) the supplier must submit documents to support FDA requirements to be proven safe and effective.
Ingredient labeling Visual check Ingredient shall be identified
Analytical
Toxicological Properties & Hazardous Substance Assessment
US FDA Canada Consumer Chemicals and Containers Regulations
Shall not contain and Hazardous or banned substances according to the regulations Toxicity Risk Assessment and Hazardous Substance Assessment shall be conducted to substantiate compliance The supplier may provide a test report dated no more than1 years to validate compliance.
Lead In Surface Coating 16 CFR 1303 Canada Consumer Product Safety Act, Surface Coating Materials Regulations
Shall not exceed 90 ppm (0.009% by weight) total lead
Physical Characteristics
Workmanship Visual No Major Defects.
Type of Container Visual Check As claimed
Liquid Purity Visual Check Shall present good liquid clarity with no visual contamination
Actual Contents (fl/oz, ml) Standard Measurement Report overall capacity -0% / +5% tolerance of label claim
Length of Non-burn area Standard Measurement Sufficient length for holding must be a minimum of 3 inches.
THE AGENT/ MANUFACTURER IS RESPONSIBLE TO ENSURE THAT THE REFERENCED STYLE CONFORMS TO ALL THE PERFORMANCE REQUIREMENTS LISTED ON THIS SPECIFICATION
AT HOME HARD GOODS PERFORMANCE SPECIFICATION SEPTEMBER 2013
NPG Supplier Procedures Manual © 2014 Nordstrom, Inc., all rights reserved. CONFIDENTIAL: These documents contain proprietary, trade secret, and confidential information which are the property of Nordstrom, Inc. These documents and their contents may not be duplicated or
disclosed to any other party without express authorization of Nordstrom, Inc. Page 12 of 28
INCENSE, AROMA OIL & INFUSERS NPS-G16 (page 2 of 2)
TEST PROPERTY TEST METHODS TEST REQUIREMENTS
Performance
Holder stability Intertek Method (M0015) No tipping or instability at 10 degree angle
Burning time Standard Measurement As claimed or report the actual
Burning performance Intertek Method No abnormality throughout the burning process 1) Ignite the end of the stick and allow the stick to burn. 2) Visual examine if the flame become self-extinguished and
then smolder, or would the flame continue to burn fiercely and consume the stick within a few seconds.
3) Visual check if the incense stick safely self-extinguished at the end of the burning process.
Flammability Of Liquids 16 CFR 1500.3 Consumer Chemicals and Containers Regulations
Must comply with all US and Canadian regulations The most stringent standard is used. Classification Flashpoint
Extremely Flammable 20F (-6.7C)
Flammable > 20F (-6.7C) and < 100F (37.8C)
Combustible > 100F (37.8C) and < 150F (65.6C)
Non-Combustible > 150F (65.6C)
Leakage test of container Consumer Chemicals and Containers Regulations
container must pass the leakage test as described in the regulation
Child Proof Container (if applicable)
16 CFR 1700 CCPSA Consumer Chemicals and Containers Regulations
If the product contains certain ingredients such as 10% or more hydrocarbons by weight and has a viscosity of less than 100 SUS at 100ºF it must include a childproof cap. Not the type if any (i.e., 2 independent motions or high torque cap).
THE AGENT/ MANUFACTURER IS RESPONSIBLE TO ENSURE THAT THE REFERENCED STYLE CONFORMS TO ALL THE PERFORMANCE REQUIREMENTS LISTED ON THIS SPECIFICATION
AT HOME HARD GOODS PERFORMANCE SPECIFICATION SEPTEMBER 2013
NPG Supplier Procedures Manual © 2014 Nordstrom, Inc., all rights reserved. CONFIDENTIAL: These documents contain proprietary, trade secret, and confidential information which are the property of Nordstrom, Inc. These documents and their contents may not be duplicated or
disclosed to any other party without express authorization of Nordstrom, Inc. Page 13 of 28
WATER GLOBES NPS-G17
TEST PROPERTY TEST METHODS TEST REQUIREMENTS *CA PROP 65 CONSENT JUDGMENT OF RELATED COURT CASE BASED ON CALIFORNIA PROPOSITION 65
Labeling
Labeling- Packaging -Fair Packaging &
Labeling Act 16 CFR 500
-Consumer Packaging & Labeling Act- R.S. 1985. c C-38 , C.R.C., c. 147
Must comply with all US and Canadian requirements. -Manufacturer, Packaging or distributors Name & Address - Product Identification - Net Quantity of Contents - Dimensions (English & Metric) - Finished Size (English & Metric)
Country of Origin Marking -19 CFR 134.11 -Canada Customs Tariff, Marking of Imported Goods Regulations, SOR-94-1 10
Must comply with all US and Canadian regulations
Verify Label Claims Visual Must Comply with all claims
Use Labeling (If applicable)
Visual Use/care instructions that are clear and understandable shall be provided in language appropriate to destination countries, if applicable.
Analytical
Lead In Surface Coating 16 CFR 1303 Canada Consumer Product Safety Act, Surface Coating Materials Regulations
Shall not exceed 90 ppm (0.009% by weight) total lead
Microbial limit test USP 61 Must meet requirements
Hazardous Chemical Test 16 CFR 1500.231 Must meet requirements
Physical Characteristics
Total Weight Standard Measurement -0% / +5% tolerance of claim
Workmanship Visual No Major Defects.
Sharp Points 16 CFR 1500.48 No Sharp Points
Sharp Edge 16 CFR 1500.49 No Sharp Edge
Attachment Visual Shall have no loose components and unsecured fastening
Performance
Flash Point 16 CFR 1500.43(a) AND 1500.3(c)(6)
Flash point above 65.6 C
Musical (Durability) Intertek Method Shall withstand 50 cycle of repeated use
Tilt Resistance Intertek Method Must withstand an angle of 10 degree with no tipping or instability.
Tension Test (On winding)
16 CFR 1500.53 (Modified) Must withstand pull 15.5lbs. @ 10 seconds
Shaking Durability Intertek Method 100X end over end – must no leaking or failure
Freezer Safe Intertek Method (M0004) No leakage or breakage after 24hrs. @-15C (5F)
Winding Key ASTM F963 The fluke of the winding key shall not have an opening in which the diameter is greater than 0.19in (5mm)
Effects of Humidity Intertek Method (M0006) No visual change after 24hrs. @95%RH,120F
Leakage test of container Consumer Chemicals and Containers Regulations
container must pass the leakage test as described in the regulation
THE AGENT/ MANUFACTURER IS RESPONSIBLE TO ENSURE THAT THE REFERENCED STYLE CONFORMS TO ALL THE PERFORMANCE REQUIREMENTS LISTED ON THIS SPECIFICATION
AT HOME HARD GOODS PERFORMANCE SPECIFICATION SEPTEMBER 2013
NPG Supplier Procedures Manual © 2014 Nordstrom, Inc., all rights reserved. CONFIDENTIAL: These documents contain proprietary, trade secret, and confidential information which are the property of Nordstrom, Inc. These documents and their contents may not be duplicated or
disclosed to any other party without express authorization of Nordstrom, Inc. Page 14 of 28
SMALL END TABLE/SIDE TABLE Metal, Aluminum, Iron, Wood, Glass Top, Resin Top NPS-G22 (page 1 of 3)
TEST PROPERTY TEST METHODS TEST REQUIREMENTS *CA PROP 65 CONSENT JUDGMENT OF RELATED COURT CASE BASED ON CALIFORNIA PROPOSITION 65
Labeling
Labeling- Packaging -Fair Packaging &
Labeling Act 16 CFR 500
-Consumer Packaging & Labeling Act- R.S. 1985. c C-38 , C.R.C., c. 147
Must comply with all US and Canadian requirements. -Manufacturer, Packaging or distributors Name & Address - Product Identification - Net Quantity of Contents - Dimensions (English & Metric) - Finished Size (English & Metric)
Country of Origin Marking -19 CFR 134.11 -Canada Customs Tariff, Marking of Imported Goods Regulations, SOR-94-1 10
Must comply with all US and Canadian regulations
Use Labeling (If applicable)
Visual Use/care instructions that are clear and understandable shall be provided in language appropriate to destination countries, if applicable.
Instructions Visual Must include clear assembly instructions, tools required, and all included hardware. Must include information on use, maintenance, and safety (load capacity and stability) as required with no errors or spelling mistakes.
Analytical
Lead In Surface Coating 16 CFR 1303 Canada Consumer Product Safety Act, Surface Coating Materials Regulations
Shall not exceed 90 ppm (0.009% by weight) total lead
California Air Resource Board (CARB) Formaldehyde Emissions from Composite Wood Products (Document Review) For wood products only
Airborne Toxic Control Measure(ATCM) California Code of Regulations Title 17,§93120 / ASTM D 6007
The covered products include finished goods composed of or containing: - Particleboard (PB); - Medium Density Fiberboard (MDF); - Thin MDF (≤8 mm in thickness); - Hardwood Plywood (HWPW) made with a composite core (veneer or composite). 1. It is the responsibilities of the manufacturers to maintain chain of custody documentation certifying materials meet CARB requirements. The documentation shall be retained for two years and readily accessible upon request. 2. The label include the fabricator's name, the date the finished good was produced and a marking to denote that the product was made with WPW, PB, or MDF that complies with the applicable Phase 1 or Phase 2 emission standards in section 93120.2(a). Finished goods shall be labeled as having been made with no-added formaldehyde based resins or ULEF resins if this is so for all HWPW, PB, or MDF used in fabricating the finished goods. 3. Document review of the following items are performed at additional charge: a. Mill's Certificate by CARB TPC b. Certificate on wooden panel used c. Labeling on the product
THE AGENT/ MANUFACTURER IS RESPONSIBLE TO ENSURE THAT THE REFERENCED STYLE CONFORMS TO ALL THE PERFORMANCE REQUIREMENTS LISTED ON THIS SPECIFICATION
AT HOME HARD GOODS PERFORMANCE SPECIFICATION SEPTEMBER 2013
NPG Supplier Procedures Manual © 2014 Nordstrom, Inc., all rights reserved. CONFIDENTIAL: These documents contain proprietary, trade secret, and confidential information which are the property of Nordstrom, Inc. These documents and their contents may not be duplicated or
disclosed to any other party without express authorization of Nordstrom, Inc. Page 15 of 28
SMALL END TABLE/SIDE TABLE (CONTINUED) Metal, Aluminum, Iron, Wood, Glass Top, Resin Top NPS-G22 (page 2 of 3)
TEST PROPERTY TEST METHODS TEST REQUIREMENTS
Physical Characteristics
Length (if applicable) Standard Measurement Report actual. Requirement -0% / +5% within tolerance of claim
Width (if applicable) Standard Measurement Report actual. Requirement -0% / +5% within tolerance of claim
Diameter (if applicable) Standard Measurement Report actual. Requirement -0% / +5% within tolerance of claim
Height Standard Measurement Report actual. Requirement -0% / +5% within tolerance of claim
Material Type Visual As claimed.
Sharp Points / Edges 16 CFR 1500.48/1500.49 (Modified)
Shall have no sharp points/edges, other than those required for function.
Defects Visual Shall have no major defect.
Shall have no discernible surface degradation, including crazing, shivering, denting, bubbles, cracks, stains, deformations, chips, fractures, heavy lines, waves, shear marks, scratches, scuff marks, indentations, or blisters
Shell present proper, even and uniform adhesion (wood)
Shall have finished edges
Matching components shall have even color throughout
Workmanship Visual Shall have no components missing, malformed or fractured.
Shall have no hardware missing
Welds shall be smoothly ground and free of pits and splatter
Shall have no burrs or sharp edges on any component
Performance
Functionality Intertek Method (M0061) Shall function as intended as received.
Distributed Load Capacity Test:
Intertek Method (M0042) Max. ¼ in deformation or no malfunction in any component when test load is applied evenly distributed on the surface. Test load based on ft
2 not to exceed 400 lb.
End Table: > 4 ft
2 10 lb/ft
2
End Table: < 4 ft2
20 lb/ft2
Distributed Load Capacity Test (Glass Top End Table):
Intertek Method (M0042) 50 lb
Concentrated Top Loading Test:
Intertek Method (M0043) No structural failure or max. ½ in deformation when test load is placed on 12 in disc 6 in from edge. Test load based on ft
2
not to exceed 300 lb. End Table: > 4 ft
2 50 lb
End Table: < 4 ft2
25 lb
Concentrated Top Loading Test (Glass Top End Table)
Intertek Method (M0043) 50 lb
Stability: Intertek Method (M0089)
Must not have any one-leg lift off the floor when test load is applied 1 in from the edge of 12 in disc to the edge (50mm for indoor/ 100mm for outdoor) from the edge in using dia.100 pad. Indoor: 0.825Lb per 10mm length Outdoor: 0.55Lb per 10mm length
Stability (Glass Top end table
Intertek Method (M0089) 50 lb
THE AGENT/ MANUFACTURER IS RESPONSIBLE TO ENSURE THAT THE REFERENCED STYLE CONFORMS TO ALL THE PERFORMANCE REQUIREMENTS LISTED ON THIS SPECIFICATION
AT HOME HARD GOODS PERFORMANCE SPECIFICATION SEPTEMBER 2013
NPG Supplier Procedures Manual © 2014 Nordstrom, Inc., all rights reserved. CONFIDENTIAL: These documents contain proprietary, trade secret, and confidential information which are the property of Nordstrom, Inc. These documents and their contents may not be duplicated or
disclosed to any other party without express authorization of Nordstrom, Inc. Page 16 of 28
SMALL END TABLE/SIDE TABLE (CONTINUED) Metal, Aluminum, Iron, Wood, Glass Top, Resin Top NPS-G22 (page 3 of 3)
TEST PROPERTY TEST METHODS TEST REQUIREMENTS
Performance (Continued)
Drop Impact Test Intertek Method (M0045) Must be serviceable without any damage or malfunction when one end of table is dropped from a height of 10 in.
Leg Strength (Non-Folding, end Table) (Side / Front)
Intertek Method (M0046) No structural failure at 50 lb applied vertically to the leg at 1 in from the end of the leg. Force is applied in four directions (forward, rearward, side to side).
Leg Strength (Folding End Table) (Side / Front)
Intertek Method (M0046)
No structural failure at 40 lb applied vertically to the leg at 1 in from the end of the leg. Force is applied in four directions (forward, rearward, side to side).
Stain Resistance ASTM D543 D3023 Shall withstand staining from common household items after 2 hr placement: wine, ketchup, mustard, grape juice cooking oil.
Resistance to Hot Water Fed. Spec. AA-11-001895B Pour 25 ml. of boiling water and allow cooling. Dry surface; shall be no graying or spotting.
Protective Components on Legs
Intertek Method Shall be non-marring.
Ease of Assembly Intertek Method (M0068)
Shall provide ease of assembly and shall be accurate.
Instruction Layout Intertek Method (M0060)
Shall be easy to follow.
Moisture Content (Wood only)
ASTM D4442 - 07 Method B (Modified)
Shall be between 8-12%. Record results of Leg and Base
Resistance to Corrosion (Metal components)
ASTM B117 (Modified)
Withstand 24 hours in 1% salt spray (fog) with no major corrosion or visual change. Modification = 1% salt (fog) spray.
Glass Top Thickness:
Raw Edge Intertek Method Less than 7.6 mm tempered glass required. Greater than 7.6 mm tempered glass not required.
Encased Intertek Method Less than 4.6 mm tempered glass required. Greater than 4.6 mm tempered glass not required.
THE AGENT/ MANUFACTURER IS RESPONSIBLE TO ENSURE THAT THE REFERENCED STYLE CONFORMS TO ALL THE PERFORMANCE REQUIREMENTS LISTED ON THIS SPECIFICATION
AT HOME HARD GOODS PERFORMANCE SPECIFICATION SEPTEMBER 2013
NPG Supplier Procedures Manual © 2014 Nordstrom, Inc., all rights reserved. CONFIDENTIAL: These documents contain proprietary, trade secret, and confidential information which are the property of Nordstrom, Inc. These documents and their contents may not be duplicated or
disclosed to any other party without express authorization of Nordstrom, Inc. Page 17 of 28
HOLIDAY STOCKINGS NPS-G25
TEST PROPERTY TEST METHODS TEST REQUIREMENTS *CA PROP 65 CONSENT JUDGMENT OF RELATED COURT CASE BASED ON CALIFORNIA PROPOSITION 65
Labeling
Labeling- Packaging -Fair Packaging &
Labeling Act 16 CFR 500
-Consumer Packaging & Labeling Act- R.S. 1985. c C-38 , C.R.C., c. 147
Must comply with all US and Canadian requirements. -Manufacturer, Packaging or distributors Name & Address - Product Identification - Net Quantity of Contents - Dimensions (English & Metric) - Finished Size (English & Metric)
Country of Origin Marking -19 CFR 134.11 -Canada Customs Tariff, Marking of Imported Goods Regulations, SOR-94-1 10
Must comply with all US and Canadian regulations
Stuffed Products Labeling
(If applicable)
-Upholstered and Stuffed Articles Regulation - Ontario Regulation 218/01 - Quebec Regulation Respecting Stuffing, Upholstered & Stuffed Articles - The Public Health Act of Manitoba, C.C.S.M. c.P210 - Bedding
---Manufacturer must register in Manitoba, Ontario and Quebec to obtain a registration number ---Sewn in label listing the filling materials in the required format
Special label Visual Shall be labeled “This is not a toy, for decoration only”
Toys Requiring Cautionary Labeling
ASTM F963
Shall Provide The Warnings:
“ WARNING Contains Small Parts Which Pose A Hazard For Children Under The Age Of Three” AND “Please Remove All Plastic Tags Before Giving Toy To A Child. These Attachments Are Not Part Of This Toy”
Age Grading Guidelines ASTM F963 Shall Be Appropriate For Use
Analytical
Lead In Surface Coating
16 CFR 1303 Canada Consumer Product Safety Act, Surface Coating Materials Regulations
Shall not exceed 90 ppm (0.009% by weight) total lead
Physical Characteristics
Fabric Weight (oz/ sq.yd) ASTM D3776 Report Actual
Dimensions Standard Measurement Report Actual (Length, Width, Other)
Workmanship Visual No Critical Defects- discoloration, fabric /sewing defects
Small Objects 16 CFR 1501 No Small Parts in as received stage
Accessible Points 16 CFR 1500.48 No Sharp Points in as received stage
Strings & Elastics ASTM F963 < 12” Length; < 14” Loop; Pull Toys > 12”, No beads Or attachments that could tangle & form Loops - as received
Packaging Film (If applicable)
ASTM F963 Average : 0.038mm
Individual : 0.03175mm
Performance
Flammability - all fabrics
Canada Textile Flammability Regulations, Items 4 and 6 CAN/CGSB 4.2 No 27.5
---Plain surface: 3.5 seconds or more ---Raised-Fiber Surface: 4 seconds or more & exhibit ignition or fusion of its base fibers.
Drop Test ASTM F963 16 CFR 1500 (As Per Table 5 - F963-07Є1
)
Torque Test ASTM F963 16 CFR 1500 (As Per Table 5 - F963-07Є1
)
Tension Test ASTM F963 16 CFR 1500 (As Per Table 5 - F963-07Є1
)
Tension Test For Seams ASTM F963 16 CFR 1500 (As Per Table 5 - F963)
Normal Use Testing ASTM F963 No Safety Hazards
Packaging/Shipping ASTM F963 No hazards, no damage to box, package or components
Crocking AATCC 8/116 Dry: Grade 4.0 Wet :Grade 3.0
Light- report 10 hours AATCC 16 Option 3 Grade 4 @ 10 hours
THE AGENT/ MANUFACTURER IS RESPONSIBLE TO ENSURE THAT THE REFERENCED STYLE CONFORMS TO ALL
THE PERFORMANCE REQUIREMENTS LISTED ON THIS SPECIFICATION
AT HOME HARD GOODS PERFORMANCE SPECIFICATION SEPTEMBER 2013
NPG Supplier Procedures Manual © 2014 Nordstrom, Inc., all rights reserved. CONFIDENTIAL: These documents contain proprietary, trade secret, and confidential information which are the property of Nordstrom, Inc. These documents and their contents may not be duplicated or
disclosed to any other party without express authorization of Nordstrom, Inc. Page 18 of 28
BEADED GARLAND NPS-G28
TEST PROPERTY TEST METHODS TEST REQUIREMENTS *CA PROP 65 CONSENT JUDGMENT OF RELATED COURT CASE BASED ON CALIFORNIA PROPOSITION 65
Labeling
Labeling- Packaging -Fair Packaging &
Labeling Act 16 CFR 500
-Consumer Packaging & Labeling Act- R.S. 1985. c C-38 , C.R.C., c. 147
Must comply with all US and Canadian requirements. -Manufacturer, Packaging or distributors Name & Address - Product Identification - Net Quantity of Contents - Dimensions (English & Metric) - Finished Size (English & Metric)
Country of Origin Marking -19 CFR 134.11 -Canada Customs Tariff, Marking of Imported Goods Regulations, SOR-94-1 10
Must comply with all US and Canadian regulations
Use Labeling (if applicable)
Visual Use/care instructions that are clear and understandable shall be provided in language appropriate to destination countries, if applicable.
Verify Label Claims Visual Must comply with all claims.
Analytical
Lead In Surface Coating
16 CFR 1303 Canada Consumer Product Safety Act, Surface Coating Materials Regulations
Shall not exceed 90 ppm (0.009% by weight) total lead
Physical Characteristics
Total Length Standard Measurement Report actual Length, shall meet label claims (-0% / +5%).
Weight (If Applicable) Standard Measurement Report overall weight; shall meet label claims (-0% / +5%).
Sharp Points/Edges 16 CFR 1500.48/1500.49 (mod.)
Shall have no sharp points/edges, other than those required for function.
Defects visual Shall have no discernible surface degradation, including crazing, shivering, denting, bubbles, cracks, stains, deformations, chips, fractures, heavy lines, waves, shear marks, scratches, scuff marks, indentations, or blisters.
Workmanship Visual Shall have no components missing, malformed, and/or fractured.
Performance
Use And Abuse Test (If Applicable To Children)
16 CFR 1500/1501 Compliance to standard
Strength Properties ASTM D5034 (Mod.) Shall Withstand 15 lb Modification= Clamping Device
Hook Strength Properties Std. Measure Shall hold 2 times weight of product
Folding Durability Actual Use 100 times cycling - No failure
Part Security Actual Use All secured parts shall be adequately secured
Effects of Humidity Intertek Method (M0006) 24hrs.@ 95 RH 120F – no failure
Flammability 16 CFR 1500.44 < 0.1” Sec (horizontal burning)
Functionality Intertek Method (M0061) Shall function as intended.
THE AGENT/ MANUFACTURER IS RESPONSIBLE TO ENSURE THAT THE REFERENCED STYLE CONFORMS TO ALL THE PERFORMANCE REQUIREMENTS LISTED ON THIS SPECIFICATION
AT HOME HARD GOODS PERFORMANCE SPECIFICATION SEPTEMBER 2013
NPG Supplier Procedures Manual © 2014 Nordstrom, Inc., all rights reserved. CONFIDENTIAL: These documents contain proprietary, trade secret, and confidential information which are the property of Nordstrom, Inc. These documents and their contents may not be duplicated or
disclosed to any other party without express authorization of Nordstrom, Inc. Page 19 of 28
SOFA AND CHAIR (Upholstered Indoor/Outdoor)
NPS-G30 (page 1 of 3) TEST PROPERTY TEST METHODS TEST REQUIREMENTS *CA PROP 65 CONSENT JUDGMENT OF RELATED COURT CASE BASED ON CALIFORNIA PROPOSITION 65
Labeling
Labeling- Packaging -Fair Packaging &
Labeling Act 16 CFR 500
-Consumer Packaging & Labeling Act- R.S. 1985. c C-38 , C.R.C., c. 147
Must comply with all US and Canadian requirements. -Manufacturer, Packaging or distributors Name & Address - Product Identification - Net Quantity of Contents - Dimensions (English & Metric) - Finished Size (English & Metric)
Country of Origin Marking -19 CFR 134.11 -Canada Customs Tariff, Marking of Imported Goods Regulations, SOR-94-1 10
Must comply with all US and Canadian regulations
Label Law(If applicable) ISPA (US & Canada) Identification of Filling Materials Registry Number
*Upholstered Furniture Label (California)
California Flammability Regulation Title 4, Chapter 3 California TB 117
Shall have a tag securely affixed which contains the required content with correct sizing requirements.
*California TB 116 Flammability Warning (if applicable, upholstered furniture)
Visual Check Shall have a tag securely affixed which contains the required content with correct sizing requirements, for products which claimed to meet TB 116 flammability requirements.
Stuffed Products Labeling
(If applicable)
-Upholstered and Stuffed Articles Regulation - Ontario Regulation 218/01 - Quebec Regulation Respecting Stuffing, Upholstered & Stuffed Articles - The Public Health Act of Manitoba, C.C.S.M. c.P210 - Bedding
---Manufacturer must register in Manitoba, Ontario and Quebec to obtain a registration number ---Sewn in label listing the filling materials in the required format
Use Labeling (if applicable)
Visual Use/care instructions that are clear and understandable shall be provided in language appropriate to destination countries, if applicable.
Verify Label Claims Visual Must comply with all claims.
Analytical
Lead In Surface Coating
16 CFR 1303 Canada Consumer Product Safety Act, Surface Coating Materials Regulations
Shall not exceed 90 ppm (0.009% by weight) total lead
PFOS (required only if declared with functional finishing - e.g. grease, stain, water repellent)
SGS Method, HPLC-MS analysis or Intertek Method-Determination of Perfluorinated Carbon (PFC) – C016.TP.
Prohibited
THE AGENT/ MANUFACTURER IS RESPONSIBLE TO ENSURE THAT THE REFERENCED STYLE CONFORMS TO ALL
THE PERFORMANCE REQUIREMENTS LISTED ON THIS SPECIFICATION
AT HOME HARD GOODS PERFORMANCE SPECIFICATION SEPTEMBER 2013
NPG Supplier Procedures Manual © 2014 Nordstrom, Inc., all rights reserved. CONFIDENTIAL: These documents contain proprietary, trade secret, and confidential information which are the property of Nordstrom, Inc. These documents and their contents may not be duplicated or
disclosed to any other party without express authorization of Nordstrom, Inc. Page 20 of 28
SOFA AND CHAIR (Upholstered Indoor/Outdoor)
NPS-G30 (page 2 of 3) TEST PROPERTY TEST METHODS TEST REQUIREMENTS
Analytical (Cont.)
California Air Resource Board (CARB) Formaldehyde Emissions from Composite Wood Products (Document Review) For wood products only
Airborne Toxic Control Measure(ATCM) California Code of Regulations Title 17,§93120 / ASTM D 6007
The covered products include finished goods composed of or containing: - Particleboard (PB); - Medium Density Fiberboard (MDF); - Thin MDF (≤8 mm in thickness); - Hardwood Plywood (HWPW) made with a composite core (veneer or composite). 1. It is the responsibilities of the manufacturers to maintain chain of custody documentation certifying materials meet CARB requirements. The documentation shall be retained for two years and readily accessible upon request. 2. The label include the fabricator's name, the date the finished good was produced and a marking to denote that the product was made with WPW, PB, or MDF that complies with the applicable Phase 1 or Phase 2 emission standards in section 93120.2(a). Finished goods shall be labeled as having been made with no-added formaldehyde based resins or ULEF resins if this is so for all HWPW, PB, or MDF used in fabricating the finished goods. 3. Document review of the following items are performed at additional charge: a. Mill's Certificate by CARB TPC b. Certificate on wooden panel used c. Labeling on the product
Physical Characteristics
Dimensions (L x W x H) (In.) Standard Measurement Report overall dimensions; shall meet label claims (if applicable). (-0%, +5%).
Weight (Lbs.) Standard Measurement Report overall weight; shall meet label claims (if applicable). (-0%, +5%).
Seat Height Standard Measurement Report overall dimension; shall meet label claims (If applicable) (-0% / +5%).
Fiber content (if applicable, Canada only)
CAN/CGSB-4.2 No. 14 Single fiber: No tolerance Blended fiber: +/- 5% tolerance
Sharp Points / Edges 16 CFR 1500.48/1500.49 (Modified)
Shall have no sharp points/edges, other than those required for function.
Defects Visual Shall have no discernible surface degradation, including crazing, shivering, denting, bubbles, cracks, stains, deformations, chips, fractures, heavy lines, waves, shear marks, scratches, scuff marks, indentations, or blisters.
Workmanship Visual No Critical Defects.
No discoloration, fabric /sewing defects or unraveling
Shell present proper, even and uniform adhesion
Shall have no components missing malformed and /or fractured
Weld shall be smoothly ground and free of pits and spatter
Shall have no loose components and unsecured fastening
Leg Height Adjustment Visual Shall conform to claimed feature.
Seat (Tilt / Non - Tilt) Visual Shall conform to claimed feature.
Seat (Rotating / Non- Rotating) Visual Shall conform to claimed feature.
Back (Fixed / Non Fixed) Visual Shall conform to claimed feature.
Arm (With / Without Arm) Visual Shall conform to claimed feature.
Base (Caster / Non - Caster) Visual Shall conform to claimed feature.
THE AGENT/ MANUFACTURER IS RESPONSIBLE TO ENSURE THAT THE REFERENCED STYLE CONFORMS TO ALL
THE PERFORMANCE REQUIREMENTS LISTED ON THIS SPECIFICATION
AT HOME HARD GOODS PERFORMANCE SPECIFICATION SEPTEMBER 2013
NPG Supplier Procedures Manual © 2014 Nordstrom, Inc., all rights reserved. CONFIDENTIAL: These documents contain proprietary, trade secret, and confidential information which are the property of Nordstrom, Inc. These documents and their contents may not be duplicated or
disclosed to any other party without express authorization of Nordstrom, Inc. Page 21 of 28
SOFA AND CHAIR (Upholstered Indoor/Outdoor)
NPS-G30 (page 2 of 3) TEST PROPERTY TEST METHODS TEST REQUIREMENTS
Performance
Flammability
California Tech 116 / 117 Must comply to the California Bureau of Home Furnishings bulletin 116/117.
Flammability - all fabrics
Canada Textile Flammability Regulations, Items 4 and 6 CAN/CGSB 4.2 No 27.5
---Plain surface: 3.5 seconds or more ---Raised-Fiber Surface: 4 seconds or more & exhibit ignition or fusion of its base fibers.
Functionality Visual Shall function as intended as received.
Back Pull Durability Intertek Method (M0017)
No failure at 100 lb for 1 min applied to 90° from back at 16 in above the seat.
Base Durability Intertek Method (M0018)
No structural failure under 500 lb compression for chair or 800Lb for sofa for 1 min.
Impact Durability (Seat) Intertek Method (M0027)
No structural breakage, max ¼ in deformation when 200 lb test load free - falls from 6 in to the center of the seat (1 drop for chair; 3 drops on different area for sofa).
Front Seating Capability Intertek Method (M0039)
No failure under 300 lb loading at edge (6 in).
Static Proof Load Test Actual Use Sample shall withstand 300 lb load, centered, for one minute. Sample must be serviceable after load is removed.
Rear Stability Intertek Method (M0038)
Min 30 lb pulling force. A 173 lb weight is placed on the seat (strap); tipping force is measured as pulled rearward against 1 in obstruction.
Front Stability Intertek Method (M0037)
The chair is obstructed by 1 in bar in the front base; tipping force is measured in the 45° to the test platform. The tipping force shall not be less than 40% of the total chair weight.
Chair Weight Intertek Method Record data.
Tipping Force Intertek Method Record data.
Arm Strength Test (Vertical) Intertek Method (M0040)
No permanent deformation at 300 lb for 1 min. The vertical load is uniformly applied through a 5 in area at the apparent weakest point.
Arm Strength Test (Horizontal) Intertek Method (M0041)
No permanent deformation at 75 lb for 1 min. The load is applied to the armrest horizontally at the most forward point of the arm rest area.
Leg Strength (Side / Front) Intertek Method (M0063)
No structural failure at 75 lb applied vertically to the leg at 1 in from the end of the leg. Force is applied in four directions (forward, rearward, side to side).
Resistance to Hot Water FED> SPEC. AA-H-001895B
Pour 25 Ml Of Boiling Water And Allow To Cool. Dry Surface Shall Have No Graying Or Spotting.
Caster Performance Actual Use Max 5 lb pull to move under 200 lb placed on the seat.
Protective Components on Legs
Visual Shall be non – marring.
Ease of Assembly Actual Use Shall provide ease of assembly and shall be accurate.
Moisture Content (%) (Wood Only):
ASTM D4442 - 07 Method B (Modified)
Record data. Report results for Leg and Base and back
Lightfastness AATCC 16 Option 3 Grade 4.0 after 40 AFU’s
Crocking AATCC8/116 Dry: Grade 4.5 Wet: Grade 3.0
THE AGENT/ MANUFACTURER IS RESPONSIBLE TO ENSURE THAT THE REFERENCED STYLE CONFORMS TO ALL THE PERFORMANCE REQUIREMENTS LISTED ON THIS SPECIFICATION
AT HOME HARD GOODS PERFORMANCE SPECIFICATION SEPTEMBER 2013
NPG Supplier Procedures Manual © 2014 Nordstrom, Inc., all rights reserved. CONFIDENTIAL: These documents contain proprietary, trade secret, and confidential information which are the property of Nordstrom, Inc. These documents and their contents may not be duplicated or
disclosed to any other party without express authorization of Nordstrom, Inc. Page 22 of 28
MIRROR
NPS-G31 (page 1 of 2) TEST PROPERTY TEST METHODS TEST REQUIREMENTS *CA PROP 65 CONSENT JUDGMENT OF RELATED COURT CASE BASED ON CALIFORNIA PROPOSITION 65
Labeling
Labeling- Packaging -Fair Packaging &
Labeling Act 16 CFR 500
-Consumer Packaging & Labeling Act- R.S. 1985. c C-38 , C.R.C., c. 147
Must comply with all US and Canadian requirements. -Manufacturer, Packaging or distributors Name & Address - Product Identification - Net Quantity of Contents - Dimensions (English & Metric) - Finished Size (English & Metric)
Country of Origin Marking -19 CFR 134.11 -Canada Customs Tariff, Marking of Imported Goods Regulations, SOR-94-1 10
Must comply with all US and Canadian regulations
Use Labeling (if applicable)
Visual Use/care instructions that are clear and understandable shall be provided in language appropriate to destination countries, if applicable.
Verify Label Claims Visual Must comply with all claims.
Analytical
Lead In Surface Coating
16 CFR 1303 Canada Consumer Product Safety Act, Surface Coating Materials Regulations
Shall not exceed 90 ppm (0.009% by weight) total lead
California Air Resource Board (CARB) Formaldehyde Emissions from Composite Wood Products (Document Review) For wood products only
Airborne Toxic Control Measure(ATCM) California Code of Regulations
Title 17,§93120 / ASTM D 6007
The covered products include finished goods composed of or containing: - Particleboard (PB); - Medium Density Fiberboard (MDF); - Thin MDF (≤8 mm in thickness); - Hardwood Plywood (HWPW) made with a composite core (veneer or composite). 1. It is the responsibilities of the manufacturers to maintain chain of custody documentation certifying materials meet CARB requirements. The documentation shall be retained for two years and readily accessible upon request. 2. The label include the fabricator's name, the date the finished good was produced and a marking to denote that the product was made with WPW, PB, or MDF that complies with the applicable Phase 1 or Phase 2 emission standards in section 93120.2(a). Finished goods shall be labeled as having been made with no-added formaldehyde based resins or ULEF resins if this is so for all HWPW, PB, or MDF used in fabricating the finished goods. 3. Document review of the following items are performed at additional charge: a. Mill's Certificate by CARB TPC b. Certificate on wooden panel used c. Labeling on the product
THE AGENT/ MANUFACTURER IS RESPONSIBLE TO ENSURE THAT THE REFERENCED STYLE CONFORMS TO ALL
THE PERFORMANCE REQUIREMENTS LISTED ON THIS SPECIFICATION
AT HOME HARD GOODS PERFORMANCE SPECIFICATION SEPTEMBER 2013
NPG Supplier Procedures Manual © 2014 Nordstrom, Inc., all rights reserved. CONFIDENTIAL: These documents contain proprietary, trade secret, and confidential information which are the property of Nordstrom, Inc. These documents and their contents may not be duplicated or
disclosed to any other party without express authorization of Nordstrom, Inc. Page 23 of 28
MIRROR
NPS-G31 (page 2 of 2) TEST PROPERTY TEST METHODS TEST REQUIREMENTS
Physical Characteristics
Length (In.) Standard Measurement As Claimed –0/+5%
Width (In.) Standard Measurement As Claimed –0/+5%
Height (In.) Standard Measurement As Claimed –0/+5%
Total Weight (Lbs.) Standard Measurement As Claimed –0/+5%
Material Type Visual As Claimed
Defects Visual Shall present proper and even adhesion
Shall present uniform adhesion (wood)
Shall present no scratches, dents, cracks, marred or discolored surface
Shall have finished edges
Components shall be even in color
Workmanship Visual No critical defects.
Shall demonstrate good, even construction, discoloration, fabric defects or unraveling.
Shall have no components missing, malformed, and/or fractured
Shall have no hardware missing
Welds shall be smoothly ground and free of pits and splatter
Shall have no burrs or sharp edges on any component
Shall have no loose component and unsecured fastening where rigidity is required
Performance
Effects Of Extreme Temperature (Environmental)
Intertek Method (M0007)
24 Hours @0 F and 120 F - No Failure
Resistance To Corrosion (Metal Components)
ASTM B117 (Mod.)
Withstand 24 hours in 1% salt spray (fog) with no major corrosion or visual change.
Effects of Humidity (Metal Components)
Intertek Method (M0006)
No Change After 24 Hrs. @ 95% RH & 120°F
Moisture Content (Wood Components)
ASTM D4442 Method B(Modified)
8%-12% Max.
Resistance To Scratching Other Surfaces (Tabletop Mirrors Only)
Visual No scratching of test surfaces (wood, glass, etc.) 3 cycles of 6” back and forth
Mirror Frame Balance Visual Will not tilt, or appear off balance - evaluate after humidity testing. For wall mounted mirrors, mount on rack, measure distance of edges parallel to floor line
Tilt Resistance (Freestanding Mirrors Only.)
Intertek Method (M0015)
No Tipping Or Instability At 10º Angle.
Hanging Strength (Wall-Mount Mirrors Only)
Intertek Method Able To Support 2 Times Actual Product Weight or 5lb whichever is greater. Hold For 1 Minute
THE AGENT/ MANUFACTURER IS RESPONSIBLE TO ENSURE THAT THE REFERENCED STYLE CONFORMS TO ALL
THE PERFORMANCE REQUIREMENTS LISTED ON THIS SPECIFICATION
AT HOME HARD GOODS PERFORMANCE SPECIFICATION SEPTEMBER 2013
NPG Supplier Procedures Manual © 2014 Nordstrom, Inc., all rights reserved. CONFIDENTIAL: These documents contain proprietary, trade secret, and confidential information which are the property of Nordstrom, Inc. These documents and their contents may not be duplicated or
disclosed to any other party without express authorization of Nordstrom, Inc. Page 24 of 28
PHOTO ALBUM, SCRAPBOOK NPS-G39 (page 1 of 2)
TEST PROPERTY TEST METHODS TEST REQUIREMENTS *CA PROP 65 CONSENT JUDGMENT OF RELATED COURT CASE BASED ON CALIFORNIA PROPOSITION 65
Labeling
Labeling- Packaging -Fair Packaging &
Labeling Act 16 CFR 500
-Consumer Packaging & Labeling Act- R.S. 1985. c C-38 , C.R.C., c. 147
Must comply with all US and Canadian requirements. -Manufacturer, Packaging or distributors Name & Address - Product Identification - Net Quantity of Contents - Dimensions (English & Metric) - Finished Size (English & Metric)
Country of Origin Marking -19 CFR 134.11 -Canada Customs Tariff, Marking of Imported Goods Regulations, SOR-94-1 10
Must comply with all US and Canadian regulations
Use Labeling (if applicable)
Visual Use/care instructions that are clear and understandable shall be provided in language appropriate to destination countries, if applicable.
Verify Label Claims Visual Must comply with all claims.
Analytical
Lead In Surface Coating
16 CFR 1303 Canada Consumer Product Safety Act, Surface Coating Materials Regulations
Shall not exceed 90 ppm (0.009% by weight) total lead
California Air Resource Board (CARB) Formaldehyde Emissions from Composite Wood Products (Document Review) For wood products only
Airborne Toxic Control Measure(ATCM) California Code of Regulations
Title 17,§93120 / ASTM D 6007
The covered products include finished goods composed of or containing: - Particleboard (PB); - Medium Density Fiberboard (MDF); - Thin MDF (≤8 mm in thickness); - Hardwood Plywood (HWPW) made with a composite core (veneer or composite). 1. It is the responsibilities of the manufacturers to maintain chain of custody documentation certifying materials meet CARB requirements. The documentation shall be retained for two years and readily accessible upon request. 2. The label include the fabricator's name, the date the finished good was produced and a marking to denote that the product was made with WPW, PB, or MDF that complies with the applicable Phase 1 or Phase 2 emission standards in section 93120.2(a). Finished goods shall be labeled as having been made with no-added formaldehyde based resins or ULEF resins if this is so for all HWPW, PB, or MDF used in fabricating the finished goods. 3. Document review of the following items are performed at additional charge: a. Mill's Certificate by CARB TPC b. Certificate on wooden panel used c. Labeling on the product
THE AGENT/ MANUFACTURER IS RESPONSIBLE TO ENSURE THAT THE REFERENCED STYLE CONFORMS TO ALL THE PERFORMANCE REQUIREMENTS LISTED ON THIS SPECIFICATION
AT HOME HARD GOODS PERFORMANCE SPECIFICATION SEPTEMBER 2013
NPG Supplier Procedures Manual © 2014 Nordstrom, Inc., all rights reserved. CONFIDENTIAL: These documents contain proprietary, trade secret, and confidential information which are the property of Nordstrom, Inc. These documents and their contents may not be duplicated or
disclosed to any other party without express authorization of Nordstrom, Inc. Page 25 of 28
PHOTO ALBUM, SCRAPBOOK NPS-G39 (page 2 of 2)
TEST PROPERTY TEST METHODS TEST REQUIREMENTS
Physical Characteristics
Total length & width (album) (inches & cm)
Standard Measurement Report overall length & width; shall meet label claims (0%/+5%)
Total length & width (page) (inches & cm)
Standard Measurement Report overall length & width ; shall meet label claims (-0%/+5%)
Thickness (page) (inches & cm)
Standard Measurement Report overall length; shall meet label claims (-0%/+5%)
Weight (Lbs.& kg) Standard Measurement Report overall weight; shall meet label claims (-0%/+5%)
Number of pages Count As labeled or claimed
Workmanship Visual No components missing, malformed and/or fractured.
Performance
Functionality ITS-M0061 Function as intended upon receipt.
Folding Endurance ITS-M0061 No damage after 100 cycles
Tensile strength Length & Width
ASTM D5034 Plastic 15.0 lbs./ In. min. Paper 5.0 lbs./ In. min.
Tear strength Length & Width
ASTM D1424
Plastic 50.0 gms/min. Paper 1.5 gms/min.
Flammability 16 CFR 1500.44 Must meet requirements <0.1 Inch/Second
Effects of Humidity ITS-M0006 No Visual Change after 24hrs. @ 95%RH, 120°F Shrinkage Less then 1.0% No adverse effects No puckering
Resistance to Corrosion (For metal components)
ASTM B117 Modified
No tarnishing 24hrs.in 1% Saline Solution
Light (Cover Material)
AATCC 16 Option 3 Class 4.0 @ 10 hours
Crocking AATCC 8 Dry 4.0 Wet 3.0
Water AATCC 107 Class 4.0 Min
THE AGENT/ MANUFACTURER IS RESPONSIBLE TO ENSURE THAT THE REFERENCED STYLE CONFORMS TO ALL
THE PERFORMANCE REQUIREMENTS LISTED ON THIS SPECIFICATION
AT HOME HARD GOODS PERFORMANCE SPECIFICATION SEPTEMBER 2013
NPG Supplier Procedures Manual © 2014 Nordstrom, Inc., all rights reserved. CONFIDENTIAL: These documents contain proprietary, trade secret, and confidential information which are the property of Nordstrom, Inc. These documents and their contents may not be duplicated or
disclosed to any other party without express authorization of Nordstrom, Inc. Page 26 of 28
WOODEN ITEMS (WOODEN BOWL, SERVING TRAY) NPS-G43 (page 1 of 3)
TEST PROPERTY TEST METHODS TEST REQUIREMENTS *CA PROP 65 CONSENT JUDGMENT OF RELATED COURT CASE BASED ON CALIFORNIA PROPOSITION 65
Labeling
Labeling- Packaging -Fair Packaging &
Labeling Act 16 CFR 500
-Consumer Packaging & Labeling Act- R.S. 1985. c C-38 , C.R.C., c. 147
Must comply with all US and Canadian requirements. -Manufacturer, Packaging or distributors Name & Address - Product Identification - Net Quantity of Contents - Dimensions (English & Metric) - Finished Size (English & Metric)
Country of Origin Marking -19 CFR 134.11 -Canada Customs Tariff, Marking of Imported Goods Regulations, SOR-94-1 10
Must comply with all US and Canadian regulations
Use Labeling (if applicable)
Visual Use/care instructions that are clear and understandable shall be provided in language appropriate to destination countries, if applicable.
Verify Label Claims Visual Must comply with all claims.
Analytical
Lead In Surface Coating
16 CFR 1303 Canada Consumer Product Safety Act, Surface Coating Materials Regulations
Shall not exceed 90 ppm (0.009% by weight) total lead
Lead Content of Consumer Products Contacting with Mouth (For products that may be touched, licked, mouthed or swallowed, e.g. straw, spout)
Canada Consumer Product Safety Act, Consumer Products Containing Lead (contact with mouth) Regulations
The following products shall not contain more than 90ppm total lead (90 mg of lead per kilogram of product ): products, other than kitchen utensils, whose normal pattern of use requires that they be brought to the user’s mouth; and products of which it is reasonably foreseeable based on their nature, that they would be used by children under 3 years of age in learning or play.
California Air Resource Board (CARB) Formaldehyde Emissions from Composite Wood Products (Document Review) For wood products only
Airborne Toxic Control Measure(ATCM) California Code of Regulations
Title 17,§93120 / ASTM D 6007
The covered products include finished goods composed of or containing: - Particleboard (PB); - Medium Density Fiberboard (MDF); - Thin MDF (≤8 mm in thickness); - Hardwood Plywood (HWPW) made with a composite core (veneer or composite). 1. It is the responsibilities of the manufacturers to maintain chain of custody documentation certifying materials meet CARB requirements. The documentation shall be retained for two years and readily accessible upon request. 2. The label include the fabricator's name, the date the finished good was produced and a marking to denote that the product was made with WPW, PB, or MDF that complies with the applicable Phase 1 or Phase 2 emission standards in section 93120.2(a). Finished goods shall be labeled as having been made with no-added formaldehyde based resins or ULEF resins if this is so for all HWPW, PB, or MDF used in fabricating the finished goods. 3. Document review of the following items are performed at additional charge: a. Mill's Certificate by CARB TPC b. Certificate on wooden panel used c. Labeling on the product
THE AGENT/ MANUFACTURER IS RESPONSIBLE TO ENSURE THAT THE REFERENCED STYLE CONFORMS TO ALL
THE PERFORMANCE REQUIREMENTS LISTED ON THIS SPECIFICATION
AT HOME HARD GOODS PERFORMANCE SPECIFICATION SEPTEMBER 2013
NPG Supplier Procedures Manual © 2014 Nordstrom, Inc., all rights reserved. CONFIDENTIAL: These documents contain proprietary, trade secret, and confidential information which are the property of Nordstrom, Inc. These documents and their contents may not be duplicated or
disclosed to any other party without express authorization of Nordstrom, Inc. Page 27 of 28
WOODEN ITEMS (WOODEN BOWL, SERVING TRAY) NPS-G43 (page 2 of 3)
TEST PROPERTY TEST METHODS TEST REQUIREMENTS
Analytical (Cont.)
Additional test for food contact items
Toxicology Indirect Food Additives: Toxicology of Coatings and Finishes (Wood-made Food Contact Surfaces)
21 CFR 175.300 Must Comply With Regulations Of US FDA Food Simulating Solvent And Extraction In lieu of testing, a passing test report may be submitted for review if dated within one year.
Wood Wax / Polish / Preservatives (for wood-made food contact articles)
21 CFR 178.3800 All ingredients shall comply to 21 CFR as a food additive ingredient, including 21 CFR 178.3800 for wood preservatives. In lieu of testing, supporting documents could be provided, confirming that: - no preservatives were used in raw materials, in manufacturing, and/or handling of finished products; OR
- they comply with the appropriate sections of 21 CFR if any preservatives were used.
Food Contact Materials (Plastics & Polymeric Coating)
FDA, 21 CFR Parts 175 & 177 per Plastic Type
Shall comply with the requirements. Vendor shall provide test reports or suitable certificates with declaration letters confirming that the materials used with food contact meet the FDA requirements as stated in CFR. (Document is valid for 1 year). Otherwise actual tests have to be performed at additional charges.
Food Grade Stainless Steel With Reference to NSF/ANSI 51 / ITS-M0122
AISI 200, 300 and 400 series stainless steel are all acceptable for food use, so are other stainless steel grades with a minimum of 16 % chromium content. In the case of cutlery / blades and similar applications requiring a sharp edge, the chromium content can be lower than 16 % if they are tempered or hardened by an appropriate post-heat treatment process. In lieu of testing, a passing test report may be submitted for review if dated within one year.
Food-contact Plastics Division 23 Food and Drug Regulations Health Canada FDA 21 CFR 177 & 175 per plastic type
Shall comply with the requirements. Vendor shall provide test reports or suitable certificates with declaration letters confirming that the plastic materials used with food contact meet specific Health Canada requirements as stated in Division 23 or are among the acceptable polymers listed by Health Canada or FDA requirements as stated in CFR. (Document is valid for 1 year). Otherwise actual tests have to be performed at additional charges.
Physical Characteristics
Dimensions ITS-M0059 Report product dimensions; shall meet label claims (-0%/+5%)
Weight ITS-M0059 Report overall weight; shall meet label claims (-0%/+5%)
Capacity ITS-M0059 Report capacity; shall meet label claims
Color Visual Check Report actual; shall meet label claims
Material Type Visual Check As claimed or observed
THE AGENT/ MANUFACTURER IS RESPONSIBLE TO ENSURE THAT THE REFERENCED STYLE CONFORMS TO ALL THE PERFORMANCE REQUIREMENTS LISTED ON THIS SPECIFICATION
AT HOME HARD GOODS PERFORMANCE SPECIFICATION SEPTEMBER 2013
NPG Supplier Procedures Manual © 2014 Nordstrom, Inc., all rights reserved. CONFIDENTIAL: These documents contain proprietary, trade secret, and confidential information which are the property of Nordstrom, Inc. These documents and their contents may not be duplicated or
disclosed to any other party without express authorization of Nordstrom, Inc. Page 28 of 28
WOODEN ITEMS (WOODEN BOWL, SERVING TRAY) NPS-G43 (page 3 of 3)
TEST PROPERTY TEST METHODS TEST REQUIREMENTS
Physical Characteristics (cont.)
Sharp Point 16 CFR 1500.49 No sharp point
Defects Visual No discernible surface degradation, including crazing, shivering, denting, bubbles, cracks, stains, deformations, chips, fractures, heavy lines, waves, shear marks, scratches, scuff marks, indentations or blisters.
Workmanship Visual No components missing, malformed and/or fractured.
Performance
Functionality ITS-M0061 Function as intended upon receipt.
Dishwasher Safe (if claimed)
ITS-M0001 Dishwasher / detergent 5 cycles - no color change or adverse effects.
Hand wash Safe (if not dishwasher safe)
ITS-M0003 Shall exhibit no exterior surface degradation after hand washed 5 times using a sponge & liquid hand washing detergent, followed by a rinse of tap water.
Stain Resistance ITS-M0014 Various food materials – mustard, ketchup, spaghetti sauce, wine, cream, and vinegar are applied to the article and let it stand for 2h. Wash the article using a dishwasher for 1 cycle and there shall not be any discoloration or staining. If the article is not dishwasher safe, it will be hand washed once.
Moisture Content (Solid Wood Only)
Standard Measurement
8%-12%
Resistance to Corrosion (For metal components)
ASTM B117 Modified
No tarnishing 24hrs.in 1% Saline Solution
Additional Tests for Bowl
Tilt Resistance / Stability (Bowl)
ITS-M0015 Shall remain stable at 10° incline without tipping after 80 % filled with water.
Thermal Shock
EN 14350-1:2004 Clause 5.6.3 (Scope Widened)
Boil the article for 10 min, then transfer immediately to 5 °C water and leave it for 10 min. There shall be no color change or adverse effects.
Microwave Safe (unless claimed to be not microwave safe, this will be tested)
ITS-M0002 5 min @ 100% power (80 % water-filled) – 2 cycles with no adverse effects.
Additional Tests for Serving Tray
Load Test Standard Measurement Withstand 1.5 times the claimed load or 10 Lbs. if not claimed. (Applied centrally with 8.5” diameter Disc) with no failure.
Handle Strength (If provided)
Standard Measurement Withstand 1.5 times the claimed load or 10 Lbs. if not claimed. (Applied centrally with 8.5” diameter Disc) with no failure.
Drop Impact Test In house method Must be serviceable without any damage or malfunction when one end of tray is dropped from a height of 10”
THE AGENT/ MANUFACTURER IS RESPONSIBLE TO ENSURE THAT THE REFERENCED STYLE CONFORMS TO ALL
THE PERFORMANCE REQUIREMENTS LISTED ON THIS SPECIFICATION