LAMA has developed over the years a wide range of products that can be used in the waterproofing and damp-proofing of roofs, decks, car parkings, walls, foundations, basements, roads,…etc.

In this catalogue, there are five main Product categories

WATERPROOFING MEMBRANES

WATERPROOFING & PROTECTIVE COATINGS

SEALANTS

BITUMINOUS FELTS

BONDING ASPHALT

OTHER PRODUCTS

WATERPROOFING MEMBRANES

Confirms to the Requirements of EN 13707 & ASTM D5147

REINFORCED FIBERGLASSAPP Modifi ed Bitumen Membrane

DescriptionMost economical waterproofing 3 or 4mm thick membrane,Excellent resistance to heat aging and weathering, Dimensional stability to membrane sheet due to the reinforcement of a rot-proof fiberglass mat 60g/m2.

Technical specificationsDimensions 1×10 m RollThickness 3 or 4mmCold Pliability no cracking at -5ºCSoftening Point 150ºC±10Penetration 20±10 dmm

OGV

WATERPROOFING MEMBRANES

WATERPROOFING MEMBRANES

Spunbond PolyesterAPP Modifi ed Membrane

DescriptionA bituminous waterproofing membrane, reinforced with Non-woven Spunbonded Polyester 150g/m2,High performing membrane,Excellent durability, flexibility and resistance to weathering and salt solutions, dilute acids.. etc.Fast, easy and clean application can be applied on existing asphalt roofing systems.

Technical specificationsDimensions 1×10 m RollThickness 3 or 4mmCold Pliability no cracking at -5ºCSoftening Point 150ºC ±10Penetration 20±10 dmm

PETRAGUM

WATERPROOFING MEMBRANES

APP Modifi ed Bitumen Membrane

DescriptionA bituminous waterproofing membrane, reinforced with Non-woven Spunbonded Polyester 180g/m2,High performing membrane,Excellent durability, flexibility and resistance to weathering and salt solutions, dilute acids.. etc.Fast, easy and clean application can be applied on existing asphalt roofing systems.

Technical specificationsDimensions 1×10 m RollThickness 3, 4 or 5mmCold Pliability no cracking at -8ºCSoftening Point 150ºC ±10Penetration 20±10 dmm

AMAN

WATERPROOFING MEMBRANES

SPUNBOND POLYESTERAPP Modifi ed Bitumen Membranes

DescriptionA bituminous waterproofing membrane, reinforced with Non-woven Spunbonded Polyester 200g/m2,Most suitable for use in TROPICAL areas,Excellent durability, flexibility and resistance to weathering and salt solutions, dilute acids.. etc.Fast, easy and clean application can be applied on existing asphalt roofing systems.

Technical specificationsDimensions 1×10 m RollThickness 3, 4 or 5mmCold Pliability no cracking at -12ºCSoftening Point 150ºC ±10Penetration 20±10 dmm

TPY

WATERPROOFING MEMBRANES

SPUNBOND POLYESTERAPP Modifi ed Bitumen Membranes

DescriptionA bituminous waterproofing membrane, reinforced with Non-woven Spunbonded Polyester 200g/m2,High performing membrane,Excellent weathering and ageing resistance.High flexibility at low temperatures.High puncture, tear, and Hydrostatic pressure resistance.

Technical specificationsDimensions 1×10 m RollThickness 3, 4 or 5mmCold Pliability no cracking at -15ºCSoftening Point 150ºC ±10Penetration 20±10 dmm

MPY

WATERPROOFING MEMBRANES

Spunbond Polyester APP Modifi ed Membrane

DescriptionA bituminous waterproofing membrane, reinforced with Non-woven Spunbonded Polyester of different weights to give the needed elongation,High performing membrane,Resistance to heat aging, puncture, and rottingExcellent durability, flexibility and resistance to weathering and salt solutions, dilute acids.. etc.Fast, easy and clean application can be applied on existing asphalt roofing systems.

Technical specificationsDimensions 1×10 m RollThickness 3, 4 or 5mmCold Pliability no cracking at (-5) – (-10) ºC depending on the reinforcementSoftening Point 150ºC ±10Penetration 20±10 dmm

ECOGUARD

WATERPROOFING MEMBRANES

SPUNBOND POLYESTERSBS Modifi ed Bitumen Membranes

DescriptionModified with Styrene Butadiene Styrene (SBS) and reinforced with Non-woven Spunbonded Polyester ranging from 180g/m2 to 200g/m2,Excellent elasticity,High aging, puncture, and tear ResistanceGood resistance to acids, sulphates and chlorides.High flexibility at low temperatures.

Technical specificationsDimensions 1×10 m RollThickness 3, 4 or 5mmCold Pliability no cracking at (-15) – (-20) ºC Softening Point 130ºC ±10Penetration 25±10 dmm

SPY

WATERPROOFING MEMBRANES

DOUBLE REINFORCEMENTAPP Modifi ed Bitumen Membrane

DescriptionMade with a double reinforcement of 180 g/m² non-woven polyester and 60 g/m² fiberglass,High dimensional stability,High thermal aging, and puncture ResistanceWithstanding extreme temperatures.

Technical specificationsDimensions 1×10 m RollThickness 4 or 5 mmCold Pliability no cracking at -5 ºC Softening Point 150 ºC ±10Penetration 20±10 dmm

GLASTER

WATERPROOFING MEMBRANES

DOUBLE-REINFORCEMENTAPP Modifi ed Bitumen Membranes

DescriptionMade with a double reinforcement of 200 g/m² non-woven polyester and 60 g/m² fiberglass,Used in heavy duty applicationsHigh dimensional stability,High thermal aging, and puncture ResistanceHydrostatic pressure and Load strain resistance.

Technical specificationsDimensions 1×10 m RollThickness 4 or 5 mmCold Pliability no cracking at -10 ºC Softening Point 150 ºC ±10Penetration 20 dmm

TPG

WATERPROOFING MEMBRANES

Bridge Deck Waterproofi ng Membranes

DescriptionMade with a double reinforcement of 250 g/m² non-woven polyester and 60 g/m² fiberglass,Designed for use in road works,High dimensional stability,Puncture & tear, Impact, and Fuel Resistance.

Technical specificationsDimensions 1×10 m RollThickness 4 or 5 mmCold Pliability no cracking at -5 ºC Softening Point 155 ºC ±10Penetration 20±10 dmm

TPG HEAVY

WATERPROOFING MEMBRANES

Anti-Root Waterproofi ng Membrane

DescriptionMade with 180 or 200 g/m2 nonwoven polyester fabric reinforced with fiberglass filaments,Bitumen is specially treated with an antiroot formulation, with the addition of Preventol B2 Used in areas where plantation can damage the waterproofing layers (Plant root resistance)High dimensional stability,Excellent elasticityHigh Puncture & tear Resistance, Resistance to aging, acids, sulfates and chlorides.

Technical specificationsDimensions 1×10 m RollThickness 3, 4 or 5 mmCold Pliability no cracking at -10 ºC Softening Point 150 ºC ±10Penetration 20±10 dmm

LAMA GARDEN

WATERPROOFING MEMBRANES

Bituminous Protection Board

DescriptionSemi rigid protection board, covered on both sides with a polyethylene filmProtect the waterproofing membrane from construction abuse and harmful puncture.It gives protection against normal foot traffic as well as the wearing caused by built-up over layers for horizontal surfaces Protection against rotting and decomposingTough and durable protective cover for protecting various waterproofing systems.

Technical specificationsDimensions 1×2 m Board or 1×10 RollThickness 3, 4, 5 and 6 mmSoftening Point 130 ±10

LAMA BOARD

WATERPROOFING AND PROTECTIVE COATINGS

WATERPROOFING & PROTECTIVE COATINGS

Highly Penetrative Bituminous Primer

PropertiesSolvent base cold applied, highly penetrative thin bituminous solution, black in color.Used for priming concrete, masonry, metal, asphalt surfaces, and as a priming coat before applying any LAMA bituminous coating, or modified bitumen membrane.Complies with the requirements of ASTM D 41 Type I.Covers from 2-3 m²/liter dependent upon porosity of surface.Supplied in 20 and 200 liter drums.

Technical specificationsFlash point 40 ºCPenetration @ 25 ºC 20-50 dmmViscosity @25 ºC 25-125 s

LAMA PRIMER

WATERPROOFING & PROTECTIVE COATINGS

Asphalt Roof Coating (Regular and Fast Drying)

A solvent-born bituminous compound of brushable consistency, dries to a tough, black coating, which does not flow under summer heat. A general purpose waterproofing and damp-proofing coating.Used as a primer where concrete surfaces are porousProvides protection against corrosion.Recommended where the threat of frost or rain precludes the use of an emulsionComplies with the requirements of ASTM D4479 Type II and BS 3416.Covers approximately 1.6 m²/liter.Supplied in 20 and 200 liter drums.

Technical specificationsFlash point 60 ºCSpecific gravity 0.90

SEALCOAT

WATERPROOFING & PROTECTIVE COATINGS

Rubberized Bitumen Emulsion, Waterproofer and Adhesive

A dark brown cold applied rubberized bitumen emulsion, dries to form a black flexible coating.Used as a water and moisture barrier, an adhesive, a plaster bonding agent and a primer.Provides protection against metal corrosionProvides weatherproofing layer when used over exposed insulationComplies with the requirements of ASTM D 1227, Type III, Class 1Covers approximately 1.3 m²/liter.As a Primer it covers approximately 5 m²/liter.Supplied in 20 and 200 liter drums.

Technical specifications:Specific gravity 980-1040Residue by evaporation 47-53 %

LAMASOL

WATERPROOFING & PROTECTIVE COATINGS

Protective Fibrated Coating A dark brown cold applied asphalt emulsion prepared emulsifying agents and containing non-asbestos fibers, for reinforcement.Used as a water and moisture barrier, also as a vapor barrier.Provides protection against metal corrosionProvides weatherproofing layer when used over exposed insulationComplies with the requirements of ASTM D 1227 type II, class 1.Covers approximately 2 m²/liter.Supplied 20 liter drums.

Technical specificationsSpecific gravity 980 – 1080Residue by evaporation 45 – 55 %

FIBERSOL

WATERPROOFING & PROTECTIVE COATINGS

Below Ground Asphalt Coating

Cutback petroleum asphalt of rapid curing type, and of brushable consistency. Dries to tough, highly adhesive, black coatings.Resists the attack of salt solutions, sulphates, and dilute acids.A general purpose waterproofing coating.Complies with the requirements of ASTM D4479 Type 1.Covers approximately 1.0 m²/liter.Supplied in 20 and 200 liter drums.

Technical specificationsViscosity 100-220 sec.Penetration @ 25 ºC 80-120 dmm.Flash Point 27 ºC

RC-25 IMPROVED

WATERPROOFING & PROTECTIVE COATINGS

Bituminous High Elastic Rubberized Coating

Cold applied bituminous rubberized solvent based compound, black in color.Excellent and full adhesion to concrete surfaces.High elasticity.Self-repairing in case of a little puncture.Moisture resistant.Covers approximately 1.0 m²/liter.Supplied in 20 liter drums.

Technical specificationsFlash point 40 ºCElongation 1000/100

RUBBERCOAT

WATERPROOFING & PROTECTIVE COATINGS

Crack Bridging and Protective Coating System For Concrete and Masonry

Waterproofing elastomeric and durable white emulsion.Provides a protective and reflective layer to the coated surface.For heat and sound insulation, waterproof and anti-rust protection.High solar reflectivity and U.V. resistance.Frost, de-icing salts and CO2 resistance.Complies with the requirements of AWWA C-203.Covers approximately 1.0 m²/liter.Supplied in 20 liter drums.

Technical specifications:Elongation at 25 °C Over 300%Service temperature -5 to 80 ˚C.Solids contents 62%

LAMACRYL

WATERPROOFING & PROTECTIVE COATINGS

Bituminous Aluminum Coating

A light/heat reflective and decorative coating.Asphalt base, aluminum-pigmented non-fibered protective coating dries to a bright silvery finish.for use over bituminous coatings, modified bitumen roofs, metal roofs, primed steel and masonry walls.Complies with the requirements of ASTM D 2824, type I.Covers approximately 0.8-1 m²/liter.Supplied in 20 liter drums.

Technical specificationsFlash point 38 °CReflectance 70%

LAMASILVER

WATERPROOFING & PROTECTIVE COATINGS

Stone Water Repellent

A transparent liquid.Closes the pores and forms a water repellent layer inside the element and at the surface while permitting the trapped vapor to move out.For coating stone, concrete, asbest-cement, and brickResistant to salt solutions, dilute acids, alkalis and U.V.Covers approximately 4 m²/liter depending on the concrete or stone porosity..Supplied in 20 liter drums.

Technical specificationsSpecific gravity about 0.8

LAMASTONE

WATERPROOFING & PROTECTIVE COATINGS

Highly Elastic Rubberized Liquid Membrane

PropertiesA liquid cold applied bituminous membrane, black in color.used to resist the plant root penetration and designed for use in planted roofsRubberized solvent based compound of a very high elasticity and Highly adhesiveGood resistance to acids, sulfates and chlorides.High flexibility at low temperaturesBonds to asphalt and bitumen surfaces, ideal for repair of failed and aged coatingsResistance to agingSupplied in 20 liter drums.

Technical specificationsFlash point 40 ºCSoftening Point 95 ºC

Garden Rubber

BONDING ASPHALT

BONDING ASPHALT

BLOWN ASPHALT85/25 & 115/15 for Built-up Roofi ng

PropertiesProduced by air blowing of petroleum residues.The grade depends on the softening point and the penetration degree.Used in the construction of built up roofing as bonding or flood coats.Complies with the requirements of B.S 3690: part 2, ASTM D312: Type III & Type IV, and Jordanian National Building code (Vol. ll-Ch5) Tables No. 15 & 17.Supplied in 180 kg drums (85 / 25) and 20 kg plastic wraps (115 / 15).

Technical specificationsPenetration @ 25 ºC 25±5 (85 / 25), 15±5 (115 / 15). Softening Point 80-90 ºC (85 / 25), 110-120 ºC (115 / 15).

BONDING ASPHALT

For MASTIC ASPHALT on Roofs

PropertiesProduced by air blowing of petroleum residues.It is mixed in-place with other components like limestone aggregate, cement and hydrated lime to give a waterproofing material, solid or semi-solid under normal weather conditions.Softens gradually when heated to 200°C, so it can be spread easily on the roofs.Used in the construction of built-up roofing as waterproofing and adhesive layerType I & IV complies with ASTM D 312.Supplied in 180 kg steel drums.

Technical specificationsPenetration @ 25 ºC 18-60 (Type I), 12-25 (Type IV)Softening Point 57-66 (Type I), 99-107 (Type IV).

OXIDIZED ASPHALT

MASTICS AND SEALANTS

MASTICS AND SEALANTS

Hot Poured Elastic Concrete Joint Sealer

PropertiesHot poured sealant composed of special asphalt, plasticizers, rubber and fillers.Used for sealing joints.Excellent Adhesion, Good Elasticity, and Water Resistance.Use 1200g for 1000cc.Complies with the requirements of B.S 2499, Type N1, ASTM D1190, ASTM D3405, ASSHTO M-173, and ASSHTO T-187Supplied in 5 gallon drum and 20 kg block..

Technical specificationsFlash point 250 ºC min.Softening Point 100 ºC min.Penetration @ 25 ºC 90 dmm max

FLEXI-JOINT

MASTICS AND SEALANTS

Concrete Joint Sealer, Hot-Poured Elastic Type

PropertiesA black resilient and adhesive compound.effectively sealing joints in concrete against penetration of moisture and foreign material Excellent adhesion to bitumen and concrete surfaces.Good elasticity, High water resistance, and Weather resistant Use 1300g for 1000cc.Complies with the requirements of B.S. 2499 (Type N2).Supplied in 20 liter steel drums.

Technical specificationsSpecific gravity 1.20Penetration @ 25 ºC 90 dmm max.

ROFLEX

MASTICS AND SEALANTS

Cold Applied, Sealant

PropertiesA blend of special asphalts, plasticizer and fillers. Soft for easy use, highly elastic and weather proof.Good adhesion without primer.Used for easy and fast sealing.Complies with the requirements of ASTM C920, Grade NS.Supplied in 20 liter drums.

Technical specificationsSpecific gravity 1.20Softening Point 80 ºC min.Penetration @ 25 ºC 85 dmm max

LAMA SEAL

MASTICS AND SEALANTS

Trowel-Applied Asphalt Roof Cement

PropertiesA black bituminous paste consists of an asphalt base, solvents, mineral stabilizers and fibers. Suitable for application by trowel or spatula.For sealing joints and cracks in bituminous membranes, concrete and other surfaces.Protect metallic surfaces and dampen their noise.Covers 0.3 m²/liter (giving 3 mm wet thickness)Complies with the requirements of ASTM D4586, Type II.Supplied in 20 liter drums.

Technical specificationsFlash point Approx. 50°C Specific gravity Approx.1.05

LAMA MASTIC

WATERPROOFING & DAMPPOOFING FELTS

WATERPROOFING & DAMPPOOFING FELTS

LAMAFELT-18Organic Fiber Base for Damp Proof Course Consists of a sheet of matted organic fibers impregnated with asphalt and coated on both faces with blown bitumen and covered with fine granules. used in built-up roofing and as a vapor barrier under roof insulationComplies with the requirements of BS 747 type 1B.

LAMAFELT-36Glass Fiber Base for Damp Proof Course

Consists of reinforced fiber glass base coated on both sides with bitumen and covered with fine granules. Suitable for use as the lower layer(s) of built-up roofing and as the top layer on flat roofs and vapor barrier under roof insulation. Complies with the requirements of BS 747 - type 3B.

WATERPROOFING & DAMPPOOFING FELTS

LAMA PERFOFELTGlass Fiber Base

A glass fiber mat with 40 mm diameter perforations saturated with asphalt and coated with bitumen and covered with fine granule surfacing material. Used primarily as a venting base sheet in built-up roofing and may be used as a loosely laid layer over the prepared substrate, beneath the torch applied LAMA waterproofing membrane.

LAMA POLYFELTFor Roofi ng and Waterproofi ng

Non-woven polyester mat saturated with oxidized bitumen and faced on the upper side with fine granule and on the bottom side with polyethylene sheet. Excellent durability, resistant to germs and yeasts, and highly flexibility.Used in built-up roofing in layers bonded in bitumen and as under lays for mopping asphalt.

WATERPROOFING & DAMPPOOFING FELTS

LAMA MESHFiberglass Net 70

A fiberglass net of excellent site serviceability, specially designed for use as a reinforcement of waterproofing coats for the roofs and foundations, to reinforce marble slabs of vertical walls and surface layers, and reinforcing cold and hot asphalt coats. It doesn’t dissolve with the organic solvents in the asphalt and it is a rot and fungi proof.

LAMA PAPERFELTAsphalt-Saturated Organic Felt

Consists of a sheet of organic fiber saturated with asphalt and covered with fine granules. Used in damp proofing of heat insulated water pipes due to its flexibility and as a vapor barrier under roof insulation, or for damp proofing in foundations.

WATERPROOFING & DAMPPOOFING FELTS

LAMA JUTEFor Roofi ng and Waterproofi ng

A woven burlap fabric saturated with asphalt and covered with one layer of polyethylene sheet on each side. used in built-up roofing in 3 or more layers bonded in hot oxidized bitumen and underlay for mastic asphalt in roofing, flooring and retaining walls. Complies with the requirements of ASTM D 1327.

OTHER PRODUCTS

OTHER PRODUCTS

STEELCOATFor protecting iron and steel

A hot applied bitumen based coating with inert non-fibrous fillers. It is solid at the normal temperatures, and softens gradually when heated turning into a very viscous liquid at about 130˚C. At higher temperatures the viscosity drops, turning the mixture into a thin and easy to apply liquid. Used to provide a protective layer over steel pipes and fittings against corrosion. Complies withrequirements of the BS4147: Type A-Grade B.

STEELPRIMEFor protecting iron and steel

A primer for cold application over iron and steel, consisting of a homogeneous solution of bitumen in a fast drying solvent. When dry, it provides an effective bond between the metal and the subsequent coating. Complies with the requirements of BS4147: Type A-Grade B.

ASPHALTOPLASTMineral Rubber

A mineral rubber blown bitumen specifically for use by polymer compound.