The HD Bluetooth Transmitter is compatible with any audio / video system that features one of the following audio outputs:

The HD Bluetooth Transmitter only supports Secured Simple Pairing (SSP) with A2DP Bluetooth audio receiving devices, such as Bluetooth speakers and headphones.

Low Latency Audio Playback The HD Bluetooth Transmitter supports 3 different Low Latency Codecs - aptX, aptX-Low Latency and FastStream.  You can enjoy wireless synchronized audio playback when the transmitter is used with compatible headphones or speakers.

The HD Bluetooth Transmitter will choose the optimal codec that is supported by the headphones or speakers. The Dual-Stream Indicator (3) will flash when a compatible low latency device is paired.

Faststream devices:(3) will flash in Green 2 timesaptX devices:(3) will flash in Green 3 times aptX Low Latency devices:(3) will flash in Green 4 times

3.5mm Audio Connector

RCA Audio Output (red and white connectors)

Digital TOSLINK Optical (S/PDIF) Connector

COMPATIBIL ITY

The Bluetooth® word mark and logos are owned by Bluetooth SIG, Inc. and any use of such marks by HomeSpot® is under license.

Demo video : https://youtu.be/UucLWQzy6T0

Bluetooth Specifications Bluetooth V4.0Bluetooth Profiles A2DPOperating Distance Typically 10m / 33ftCharging Input DC 5V/ 0.5ABattery Life Transmits up to 7 hours of operationCharging Time About 1 hourWeight 26g / 0.92ozModel BTADP-128-D

HomeSpot ® Dual Stream HD Bluetooth Audio Transmitter

TECHNICAL SPECIF ICATIONS

Connect the micro-USB cable (9a) to the micro-USB Charging Jack (5) of the HD Bluetooth Transmitter.

The Battery Indicator (4) will turn on to indicate charging in progress. The Battery Indicator will turn off once the unit is fully charged.

The HD Bluetooth Transmitter can be operated even when it is being charged.

When it is not connected to a USB power source, it will operate with the built-in battery. The Battery Indicator (4) will blink in red when the battery level is low, indicating that recharging is needed.

1. Remove the protective caps from the Optical TOSLINK Audio Cable included in the package.

The custom-shaped TOSLINK connector cable is designed to fit into only one

position. Do not exert unnecessary force when inserting the

CHARGING

SETTING UP YOUR HD BLUETOOTH TRANSMITTER

cable. Do not attempt to bend or fold the TOSLINK cable into an angle, as this may permanently damage it.

2. Connect the TOSLINK cable (12a) (12b) between the optical output of your audio / video system and the optical input (7) of the HD Bluetooth Transmitter.

3. The HD Transmitter accepts only digital audio input in uncompressed stereo PCM format. The default digital audio output of most TVs are PCM. However, in some cases, you may have to change the digital audio output setting of your TV, DVR, or set-top box to PCM format.

4. For some TVs, you may need to turn on the Internal Mute (the built-in TV speakers) to send audio to the digital and/or analog RCA audio output jacks on the side panel.

5. Some TVs do not send audio to the digital audio jack in certain circumstances, e.g. if the input source is HDMI, or if the video content is not in digital format. In such cases, use the analog RCA audio connection on the TV side panel.

6. For PS3 game consoles, select only [Linear PCM 2 Ch. 44.1kHz] and [Linear PCM 2 Ch. 48kHz] (deselect all others) output format in the PS3 audio settings. If you connect the Transmitter directly to the optical output of the PS3, set the Audio Multi-Output to ON. For more information, check out http://manuals.playstation.net/document/en/ps3/current/settings/audiooutput.html

7. If the video source is Comcast DVR, change the Audio Device Setting of the DVR from Surround to Stereo.

NOTE: If both the 3.5mm Audio Input (6) & the Digital TOSLINK Optical Audio Input (7) are connected, only the 3.5mm Audio Input will be played.

1. Connect one end of the audio cable (10a) or (11a) to the 3.5mm Audio Input (6) of the HD Bluetooth Transmitter.

2. Connect the other end of the audio cable (10b) or (11b) to the audio output of your audio / video system. Consult your audio / video system user manual for more information on how to accomplish this.

TIPS : If your audio / video system features a RCA audio output port, use the bundled RCA cable for better user experience.

Some TV Speakers will be muted automatically when the headphone jack is in use. The volume of the headphone jack can be adjusted using the TV or the receiver, and this will affect the volume of the HD Bluetooth Transmitter.

SETTING UP YOUR HD BLUETOOTH TRANSMITTER

1. Power on your Bluetooth audio receiving device and set it to pairing mode.

2. On the first use, once powered on, the HD Bluetooth Transmitter will be in pairing mode. (2)& (4) LED lights will alternate blink rapidly in turn once the unit is powered.

3. The HD Bluetooth Transmitter will automatically search for, and connect to, the closest Bluetooth audio receiving device in pairing mode.

4. If the pairing is successful and a connection is made, (2) will blink in blue every 5 seconds.

The HD Bluetooth Transmitter will remain in pairing mode for 120 seconds, or until successfully paired. After 120 seconds, you can press the MFK button to set the HD Bluetooth Transmitter to pairing mode again.

TO PAIR WITH A 2nd BLUETOOTH DEVICEBefore the HD Bluetooth Transmitter can be set to enable dual streaming, it needs to be paired with the 2nd Bluetooth audio device first.After the HD Bluetooth Transmitter has been paired with the 1stdevice, switch off the Transmitter first. Simply press-&-hold (1)

PAIRING

light blinksin Blue

light blinksin Red

PAIRING WITH BLUETOOTH DEVICE(S)

PACKAGE CONTENTS

USB A - micro USB Cable

3.5mm - 3.5mm audio cable

3.5mm - RCA audio cableOptical TOSLINKAudio Cable

HD BluetoothAudio Transmitter

User Guide Warranty Card

1) Multifunction Button 5) micro-USB Charging Jack2) Pairing Status Indicator 6) 3.5mm Audio Input3) Dual-Stream Indicator 7) Digital TOSLINK Optical Audio Input4) Battery Indicator 8) High/Low Volume Switch

PACKAGE CONTENTS

PRODUCT OVERVIEW

for 3 seconds while the Transmitter is still turned on.

Follow the same pairing step 3. If pairing is successful and the newly paired device is connected, (2) will blink in blue every 5 seconds.

Ensure that your two Bluetooth audio receiving devices have previously been paired successfully. Follow the pairing steps above if this has not been done so earlier.

Make sure that the HD Bluetooth Transmitter is connected to one of the audio receiving devices, and (2) should blink in blue every 5 seconds when connected.

2. While the first device` is connected, double press (1) to switch the HD Bluetooth Transmitter into dual stream mode.

3. When trying to reconnect to the 2nd Bluetooth audio receiving device, (3) will blink in green.

4. If the re-connection is successful, (3) will remain steady in green, and both devices will play audio from the HD Bluetooth Transmitter simultaneously.

• If the re-connection fails, (3) will blink in red 3 times. Make sure that the 2nd device is available for re-connection.

1.

STREAMING AUDIO TO TWO DEVICES (DUAL STREAMING)

p.1 p.2 p.3 p.4

p.5 p.6 p.7 p.8

Status LED Indications

(2) blinks while in re-connection mode.

1. The High / Low volume switch can be used to adjust the volume of the audio transmission.

2. Always try to adjust the volume from the audio / video system.

3. Adjust the volume level on your Bluetooth audio receiving device(s).

4. If the volume output is still too high, too low, or if you notice audible distortion, switch (8) to your desired level.

5. You will need to power up the HD Bluetooth Transmitter again for the new volume setting to take effect.

While the HD Bluetooth Transmitter is turned off, press and hold the MFK button (1) for 10 seconds until (2) blinks in blue for 3 times. The unit will then enter pairing mode ((2) & (4) will blink alternately) and all previously paired devices will be deleted from memory.

FACTORY RESET

HIGH / LOW VOLUME SWITCH

Pairing Mode

Lights blink in Blue and Red alternately.

Re-connection Mode

Light blinks in Blue for 5 seconds. If no device is found, the unit goes into standby mode.

Power Off

Press & hold the MFK button for 3 secs until the LED goes off.

Standby Mode

Lights remain steady in Blue.

You can press the MKF button once to go into pairing mode / re-connection mode.

Standard Device Connected

Blue LED blinks every 5 seconds.

light blinks in Red

light blinks in Blue

light blinks in Red

light blinks in Blue

remains steadyin blue

light blinks in Bluefor 5 secs

Blinks in blueevery 5 seconds

Note: When streaming audio to two headphones / speakers, the HD Bluetooth Transmitter will select by default the optimal codec supported by each device. For example, if one of the headphones supports aptX and the other does not, the Bluetooth Transmitter will stream aptX audio to the aptX compatible headphone, and stream regular Bluetooth SBC audio to the regular Bluetooth headphone.

While in dual streaming mode, the Bluetooth transmission range will be slightly affected. For the best experience, it is suggested to operate the HD Bluetooth Transmitter and the headphones / speakers within 10m with line of sight.

The HD Bluetooth Transmitter will automatically power off if no device is connected in 2 minutes.Short press the MFK button to power up the HD Bluetooth Transmitter again.

When the HD Bluetooth Transmitter is in standby mode (i.e. when (2) remains steady in blue) or in OFF mode, make sure that your audio receiving device is in pairing mode, then press (1) again and the Transmitter will automatically re-connect to

the last connected device, and (2) will blink in blue every 5 seconds.The Transmitter will search for the last two connected devices for 60 seconds upon power up, and will automatically connect to the first of the last two connected device found, as

AUTO-POWER OFF

AUTO-RECONNECT TO LAST TWO CONNECTED DEVICES

Dual Streaming(Failed)

Blinks in Red 3 times

Battery Low

Blinks in Red

Blinks in blueevery 5 seconds

Blinks in Red 3 times

Blinks in Red

LED INDICATORS

1. Place the HD Bluetooth Transmitter within 1 meter of your Bluetooth audio receiver during the pairing process.

2. The pairing mode will last for 2 minutes. If no devices can be connected within 2 minutes, the HD Bluetooth Transmitter will enter standby mode, and (2) remains steady in blue.

3. Switch off the HD Bluetooth Transmitter and repeat the pairing steps if it fails to pair.

4. The HD Bluetooth Transmitter will save up to 2 device pairing records, and only those 2 previously paired devices will be automatically re-connected when the Transmitter is powered on.

5. When a third device is paired, the first device pairing record will be removed.

The internal antenna of the HD Bluetooth Transmitter has been fine-tuned to provide a wide operating range. When the product is properly placed with an uninterrupted line of sight and there is no radio interference, it can typically achieve transmission distances ranging from 10-20m.

Do not surround the HD Bluetooth Transmitter with metallic objects or put it behind any electronic appliances. Doing so will severely reduce the transmission performance. Please ensure that there are no obstacles (walls, corners, partitions etc.) between the Transmitter and the Bluetooth receiving devices.

NOTES

Faststream Device Connected

(3) flashes in Green 2 times immediately after connection.

aptX Device Connected

(3) flashes in Green 3 times immediately after connection.

aptX Low Latency Device Connected

(3) flashes in Green 4 times immediately after connection.

Dual Streaming(Successful)

Remains Steady in Green

Dual Streaming Re-connected

Blinks in Green

p.9 p.10 p.11 p.12