Home > Documents > Heatless Regenerative Air/Gas Dryers

Heatless Regenerative Air/Gas Dryers

Date post: 12-Mar-2022
Category:
Author: others
View: 2 times
Download: 0 times
Share this document with a friend
Embed Size (px)
of 4 /4
Heatless Regenerative Air/Gas Dryers PH/EH Series Section 20 Bulletin A-10-PH
Transcript
• • • • • • • • • • • • • • • • • • • • • • • • •
••••• ••••• ••••• ••••• •••••
Use of this Motor Challenge logo does not imply DOE endorsement.
Pneumatech reserves the
specifications and product
design in connection
products. Such changes
corresponding changes,
previously sold or shipped.
Pneumatech 4909 70th Avenue Kenosha, Wisconsin U.S.A. 53144 (262) 658 -4300 Fax: (262) 658 -1945
w w w. p n e u m a t e c h . c o m
Distributed by:
0906
Clean, dry compressed air is vital to your busy production environment. If left untreated,
compressed air can damage your system and end product. Incorporating high-quality
components and energy-saving options, Pneumatech’s regenerative air dryers can
provide you with clean, dry air to extend the life of your equipment and products. With
decades of knowledge and in-house expertise, Pneumatech provides a wide range
of high performance solutions to meet any standard or custom package application.
O P T I O N S
• Dew Point Demand (DPD)
- Senses dew point at outlet of the dryer
- Extends valve life
- Digitial Dew Point Display
• -100°F dew point
F E A T U R E S
• Digital MicroProcessor (DMP) Control featuring Cycle Sight shows cycle time and tower status
• Dry contacts for alarm outputs
• Cycle advance push button
• Automatic repressurization
- Ball valves with Teflon seats and seals up to PH-250
- Wafer style butterfly valves with buna seats PH-300 to PH-3100
• Less than 3 PSID at rated flow
• Industry low purge rate – 14%
• Towers meet ASME and CRN requirements
• Extra tower corrosion allowance
• Industrial enamel paint finish
S P E C I F I C A T I O N S
Model* Purge Flow
In/Out Conn. Size
Desiccant lbs./tower
Shipping Weight lbs.
PH-35 4.9 0.75” NPT 36.27 x 22.14 x 63.31 23 390
PH-50 7 0.75” NPT 36.27 x 22.14 x 63.31 33 450
PH-75 10.5 1” NPT 40.27 x 24.22 x 60.12 50 500
PH-100 14 1” NPT 40.27 x 24.22 x 74.18 65 550
PH-150 21 1.5” NPT 51.06 x 24.6 x 75.87 100 600
PH-200 28 1.5” NPT 52.09 x 28.21 x 71.9 130 775
PH-250 35 1.5” NPT 48 x 26 x 83.9 165 800
PH-300 42 2” NPT 58.7 x 31.2 x 80.5 195 1050
PH-350 49 2” NPT 58.7 x 31.39 x 90.5 230 1200
PH-400 56 2” NPT 63.26 x 40.07 x 81.68 265 1285
PH-500 70 2” NPT 63.26 x 40.88 x 81.68 340 1500
PH-650 91 2” NPT 63.26 x 41.88 x 96.13 410 2170
PH-750 105 2.5” Flange 79.88 x 42 x 99.66 460 2400
PH-1000 140 2.5” Flange 79.88 x 43.88 x 91.66 725 2700
PH-1250 175 3” Flange 86.19 x 40 x 107.16 850 3200
PH-1500 210 3” Flange 92 x 48 x 91.16 1020 3750
PH-1800 252 4” Flange 103.77 x 52.85 x 108.83 1150 4400
PH-2100 294 4” Flange 108 x 55.85 x 98.83 1375 5600
PH-2600 364 4” Flange 108 x 55.85 x 110.83 1650 6800
PH-3100 434 6” Flange 110 x 56 x 134.95 1950 7600
The EH series is an economical choice that features high quality, 2-way pilot operated diaphragm type valves.
Model* Purge Flow
In/Out Conn. Size
Desiccant lbs./tower
Shipping Weight lbs.
EH-35 4.9 0.75” NPT 36.27 x 22.14 x 63.31 23 400
EH-50 7 0.75” NPT 36.27 x 22.14 x 63.31 33 425
EH-75 10.5 1” NPT 40.27 x 24.22 x 60.12 50 450
EH-100 14 1” NPT 40.27 x 24.22 x 74.18 65 545
EH-150 21 1.5” NPT 51.06 x 24.6 x 75.87 100 590
EH-200 28 1.5” NPT 52.09 x 28.21 x 71.9 130 790
EH-250 35 1.5” NPT 48 x 26 x 83.9 165 850
EH-300 42 2” NPT 58.7 x 31.2 x 80.5 195 1030
EH-350 49 2” NPT 58.7 x 31.39 x 90.5 230 1225
EH-400 56 2” NPT 63.26 x 40.07 x 81.68 265 1300
EH-500 70 2” NPT 63.26 x 40.88 x 81.68 325 1500
EH-650 91 2” NPT 63.26 x 41.88 x 96.13 410 2020
*Model number indicates SCFM flow at 100 PSIG, 100°F.
CUSTOM UNIT
Operating Specifications Operating Pressure: 100 PSIG Operating Temp: 100º F Maximum Inlet Temp: 120º F Minimum Inlet Temp: 70º F Design Pressure: 150 PSIG at 450º F (Vessels) Outlet Dew Point: -40º F Power Supply: 115V – 1PH – 60HZ Electricals: NEMA 4 NEMA Cycle: 10 Minutes Desiccant: Activated Alumina
PH-500
Clean, dry compressed air is vital to your busy production environment. If left untreated,
compressed air can damage your system and end product. Incorporating high-quality
components and energy-saving options, Pneumatech’s regenerative air dryers can
provide you with clean, dry air to extend the life of your equipment and products. With
decades of knowledge and in-house expertise, Pneumatech provides a wide range
of high performance solutions to meet any standard or custom package application.
O P T I O N S
• Dew Point Demand (DPD)
- Senses dew point at outlet of the dryer
- Extends valve life
- Digitial Dew Point Display
• -100°F dew point
F E A T U R E S
• Digital MicroProcessor (DMP) Control featuring Cycle Sight shows cycle time and tower status
• Dry contacts for alarm outputs
• Cycle advance push button
• Automatic repressurization
- Ball valves with Teflon seats and seals up to PH-250
- Wafer style butterfly valves with buna seats PH-300 to PH-3100
• Less than 3 PSID at rated flow
• Industry low purge rate – 14%
• Towers meet ASME and CRN requirements
• Extra tower corrosion allowance
• Industrial enamel paint finish
S P E C I F I C A T I O N S
Model* Purge Flow
In/Out Conn. Size
Desiccant lbs./tower
Shipping Weight lbs.
PH-35 4.9 0.75” NPT 36.27 x 22.14 x 63.31 23 390
PH-50 7 0.75” NPT 36.27 x 22.14 x 63.31 33 450
PH-75 10.5 1” NPT 40.27 x 24.22 x 60.12 50 500
PH-100 14 1” NPT 40.27 x 24.22 x 74.18 65 550
PH-150 21 1.5” NPT 51.06 x 24.6 x 75.87 100 600
PH-200 28 1.5” NPT 52.09 x 28.21 x 71.9 130 775
PH-250 35 1.5” NPT 48 x 26 x 83.9 165 800
PH-300 42 2” NPT 58.7 x 31.2 x 80.5 195 1050
PH-350 49 2” NPT 58.7 x 31.39 x 90.5 230 1200
PH-400 56 2” NPT 63.26 x 40.07 x 81.68 265 1285
PH-500 70 2” NPT 63.26 x 40.88 x 81.68 340 1500
PH-650 91 2” NPT 63.26 x 41.88 x 96.13 410 2170
PH-750 105 2.5” Flange 79.88 x 42 x 99.66 460 2400
PH-1000 140 2.5” Flange 79.88 x 43.88 x 91.66 725 2700
PH-1250 175 3” Flange 86.19 x 40 x 107.16 850 3200
PH-1500 210 3” Flange 92 x 48 x 91.16 1020 3750
PH-1800 252 4” Flange 103.77 x 52.85 x 108.83 1150 4400
PH-2100 294 4” Flange 108 x 55.85 x 98.83 1375 5600
PH-2600 364 4” Flange 108 x 55.85 x 110.83 1650 6800
PH-3100 434 6” Flange 110 x 56 x 134.95 1950 7600
The EH series is an economical choice that features high quality, 2-way pilot operated diaphragm type valves.
Model* Purge Flow
In/Out Conn. Size
Desiccant lbs./tower
Shipping Weight lbs.
EH-35 4.9 0.75” NPT 36.27 x 22.14 x 63.31 23 400
EH-50 7 0.75” NPT 36.27 x 22.14 x 63.31 33 425
EH-75 10.5 1” NPT 40.27 x 24.22 x 60.12 50 450
EH-100 14 1” NPT 40.27 x 24.22 x 74.18 65 545
EH-150 21 1.5” NPT 51.06 x 24.6 x 75.87 100 590
EH-200 28 1.5” NPT 52.09 x 28.21 x 71.9 130 790
EH-250 35 1.5” NPT 48 x 26 x 83.9 165 850
EH-300 42 2” NPT 58.7 x 31.2 x 80.5 195 1030
EH-350 49 2” NPT 58.7 x 31.39 x 90.5 230 1225
EH-400 56 2” NPT 63.26 x 40.07 x 81.68 265 1300
EH-500 70 2” NPT 63.26 x 40.88 x 81.68 325 1500
EH-650 91 2” NPT 63.26 x 41.88 x 96.13 410 2020
*Model number indicates SCFM flow at 100 PSIG, 100°F.
CUSTOM UNIT
Operating Specifications Operating Pressure: 100 PSIG Operating Temp: 100º F Maximum Inlet Temp: 120º F Minimum Inlet Temp: 70º F Design Pressure: 150 PSIG at 450º F (Vessels) Outlet Dew Point: -40º F Power Supply: 115V – 1PH – 60HZ Electricals: NEMA 4 NEMA Cycle: 10 Minutes Desiccant: Activated Alumina
PH-500
• • • • • • • • • • • • • • • • • • • • • • • • •
••••• ••••• ••••• ••••• •••••
Use of this Motor Challenge logo does not imply DOE endorsement.
Pneumatech reserves the
specifications and product
design in connection
products. Such changes
corresponding changes,
previously sold or shipped.
Pneumatech 4909 70th Avenue Kenosha, Wisconsin U.S.A. 53144 (262) 658 -4300 Fax: (262) 658 -1945
w w w. p n e u m a t e c h . c o m
Distributed by:

Recommended