Helling Engl KATALOG

7/28/2019 Helling Engl KATALOG

1/42

Testing

Geschichte von Helling

27 August 2007

Non destructive

testing


2/42

2

Dear reader!

Herewith I would like to introduce you to the company

HELLING. The catalogue will give you an insight intoour delivery program concerning equipment, products

and accessories for Non Destructive Testing.

HELLING company was founded in 1863 and has long

experience concerning the European market. Constant

growth and partnership have been contributing to

consequent development of the company and today

HELLING is a leading manufacturer and supplier for

high quality equipment and products for Non

Destructive Testing in more then 39 countries.HELLING company is a member of German

Association for Non Destructive Testing (DGZfP) and also of Russian Association of Non

Destructive Testing & engineering diagnostics, Czech association of Non Destructive

Testing, Japan and American Associations.

Based on well-developed scientific foundation we design and offer unique testing techniques,

corresponding to world standards requirements.

We hope for long and beneficial co-operation,

Yours faithfully,

President of HELLING

N. Riess


3/42

3

HELLING GmbH Spkerdamm 2 D-25436 Heidgraben (bei Hamburg) Postfach 2132 D-25437 TorneschTelephone: +49(0)4122 922-0 Telefax: +49(0)4122 922-201 e-mail: [email protected] www.hellinggmbh.de

Contents

Penetrant testing

Dye penetrant method (red-white) 4Fluorescent method 6

Penetrant testing systems 7

Test panels 8

Magnetic particle testing

Magnetizing devices 11

Stationary test facilities 13

Demagnetizations 13

Colored magnetic particles 14

Fluorescent magnetic particles 15

Additional products 16Reference blocks 18

Black light

Stationary UV lamps 20

Portable UV lamps 21

UV-LED-sources 22

Leak testing

Bubble method 23

Hydrogen leak detector 24

Helium leak detector 24

Ultrasonic leak detector 25

Fluorescent concentrate 26

Radiographic testing

Radiographic films 27

Developing machines 29

Accessories 30

Ultrasonic testing

Ultrasonic thickness gauge 31

Ultrasonic test facilities 31

Accessories 32

Auxiliary equipment for weld

inspection 33

Temperature detection 35

Delivery program 40


4/42

4

Penetrant testing (PT), how it works

The penetrant method of non-destructive testing is based on capillary penetration of indicator

liquid (penetrant) into the surface defects (cracks, pores etc.). After intermediate cleaning and

subsequent drying, a developer is applied as a thin, white layer onto the surface to be

inspected. The developer pulls the penetrant out of the surface defects and makes themvisible as coloured, linear or rounded indications. Documentation is possible by means of

adhersive foil, photographic or video techniques.

Procedure of penetrant inspection.

Precleaning

Mechanically, with brush By stream process Degreasing with hot steam Cleaning with solvent

Predrying

Application ofpenetrant.

Dip in bath Laying with brush Application by spraying Application by electrostatic mean

Intermediate

cleaning

With lint free cloth, water-moistened or a

spongeWith water-moistened brush Rinse with water With lint free cloth or sponge,

moistened with a special solvent

Drying

Dry in open air Wipe with a lint free cloth Blow with dry, clean air Dry with warm air

Application of

developer

By immersion(aqueous developer) Application from the diffuser /aerosol (non-aqueous developer)

Electrostatic application(non-

aqueous developer)

Application of dry powder developer(

in special cases, e.g. extremely porous

surfaces)

Examination of the

surface and

documentation

Viewing under day light or in artificial

illumination min.. 500 Lux (EN 571-1/EN

3059)

If using fluorescent penetrant:

Ambient illumination: < 20 Lux

Intensity of UV: 1000W/cm2

Documentation by adhasive foil Photo-optical documentation Documentation by means of videofilming or photocamera

Penetrant testing systems

Met-L-Chek, Standard Chek, Nord-Testare reliable in detecting the defects with awidth down to the range ofm.

Necessary condition: defects must be opento surface.Systems are also used for the leak testing.

The examination of testing

media adequacy is done inaccordance with :

AMS 2644

AMS 2647

DIN EN ISO 3452-2 (3)

ASME

Penetrant inspection can accurately and

easily detect surface defects independent oftypes, materials and surface configurations ofthe objects to be tested. Other methods of

non destructive testing, can only be appliedfor these requirements with restrictions.


5/42

5

Products are available in aerosol tanks (400 and 500 ml), containers(1; 10 l) and barrels (200 l).

Contrast (red-white) method

Areas of us e:

Aircrafts industry, Metallurgy, nuclear industry, Electrical engineering, Engineering, Foundry, Blanking, Shipbuilding, Medicine,Car production.

Work with materials:Alloyed and plain steel, cast iron, platings, plastics*, welds, nonferrous metals, products of powder metallurgy, steatite,ceramics*, other synthetic materials.

*check for adequacy

MET-L-Chek, Standard-Chek & Nord-Test*

Used in temperature ranges from -5 to + 50. In low temperatures (from -5 to + 10 ) it is necessary to increase time ofpenetrating. One must take into account peculiar specifications according to DIN EN ISO 3452 part 2 & EN 571 part 1. Forexamination in higher temperatures (from +10 to + 175) Super-Chek was especially developed..

MET-L-Chek, checked and approved

DIN EN ISO 3452-2, EN 571, KWU correspond to requirements: Lloyd's Register of Shipping, Bureau Veritas, Bureau CentralHollandais, Germanischer Lloyd, MIL-I-25135/QPL-25135, AMS 2644, ASME Boiler and Pressure Vessel, ASTM E-165,

ASTM-E1417, certificated NAVSEA 250-1500-1, RDT & EdF, RCC-

Standard- Chek & Nord-Test examined and approved according to: DIN EN ISO 3452-2, EN 571, KWU correspond to requirements Lloyd's Register of Shipping, Bureau Veritas, Bureau CentralHollandais, Germanischer Lloyd, MIL-I-25135/QPL-25135, AMS 2644, ASME Boiler and Pressure Vessel, ASTM E-165,

ASTM-E1417.Content of sulfur is determined according to ASTM D 516-88, examination of the content of halogens (fluorine and chlorine) isdetermined in accordance with ASTM E 165-91, application 2, method A and ASTM E 165-91, application 3.

Example of Nord-Test penetrant system

Remover U87 Penetrant U88 Penetrant Red 3000 Developer U89 Environmentally

safe remover on

a solvent base.

Fumes fast.

Doesnt leavedints.

High sensitivity

Easily cleansed with water

Smells slightly

Sensitivity according to:DIN EN ISO 3452-2II-level (high sensitive)

Ultra high level of sensitivity

Water washable

Doesnt contain AZO-colouring agents

Smells slightly

Testing by luminescent method, by means of

ultraviolet illumination is possible

Sensitivity according to:DIN EN ISO 3452-2 II-level (high sensitive)

Fine-grained whitepowder on a spirit

base ,

Doesnt containaroma additives.

1 2 3

Indication of cracks on standard panel1

(max width of cracks 1,5 m, depth 28,5 m) by use of

NORD-TEST (U87, Rot 3000, U89)system under following

viewing conditions:

1.At day light (500 Lux)

2.At day light (500 Lux) +ultraviolet(1000 W/cm2) illumination

3.At ultraviolet illumination (5 Lux, 1000 W/cm2)


6/42

6 Available in cans(1; 10 l) and barrels (200 l).

Develo

per

RemoverEmulsifier

Penetrant

Fluorescent method**

Fluorescent penetrants according to AMS-2644 & ASTM E-1417

REMOVAL METHODS:A Water washable

B Post emulsifiable, lipophilic emulsifier.

C Solvent wipe removal

D Post emulsifiable ,hydrophilic emulsifier

(17-20%: dip or < 5%: spray, concentrations).SENSITIVITY LEVEL:1/2 very low; 1 low; 2 medium; 3 high; 4- very highDEVELOPER FORMS: a Dry developer; Use with all the fluorescent penetrants(Type I), Methods A, B, C & D.

b Water soluble type; Use with fluorescent penetrants (Type I), Methods B, C & D.

c Water suspendable developer ; Use with all the penetrants , Methods A, B, C & D.

d Nonaqueous developer; use with (Type I) penetrants , Methods A, B, C & D.

e - Nonaqueous developer; use with (Type II) penetrants, Methods A, B, C & D.

f Special application material.

SOLVENT CLASS: 1 Halogenated solvent remover, use with all penetrants, Method C.

2 Nonhalogenated solvent remover, use with all penetrants, Method C.

3 Special application material used with special application penetrants, Method C.

Name TypeMethodClass/

form

Sensitivitylevel

AMS-2644

QPL4

General description

FP-900 I A & C 1/2 YES Very low sensitivity, general metal working

FP-901 I A & C 1 YES Low sensitivity, general metal working

FBP-911 I A & C 1 YES Low sensitivity, oil and solvent free

FP-921 I A & C 1 YES Low sensitivity, aerospace applications

FP-902 I A & C 2 YES Medium sensitivity, general metal working

FBP-912 I A & C 2 YES Medium sensitivity, oil and solvent free

FP-922 I A & C 2 YES Medium sensitivity, aerospace applications

FP-903 I A & C 3 YES High sensitivity, all applications

FBP-913 I A & C 3 YES High sensitivity, oil and solvent free

FB-923 I A & C 3 YES High sensitivity, aerospace applications

FBP-914 I A & C 4 YES Ultra High sensitivity, oil & solvent free

FP-93A(M) I B, C & D 2 YES Medium sensitivity, all applications

FP-95A(M) I B, C & D 3 YES High sensitivity, all applications

FP-97A(M) I B, C & D 4 YES Ultra high sensitivity, all applications

E-57 I B NA YES Lipophilic emulsifier forFP-93/95/97A(M)

E-58D I D NA YES Hydrophilic emulsifier forFP-93/95/97A(M)

E-59 I & II C, class 2 NA YES Solvent remover for all penetrants

E-59A I & II C, class 2 NA YES Solvent cleaner / remover for all penetrants

R-502* II C, class 3 NA NA Special high temperature remover

D-70 I & II Forms d & e NA YES Nonaqueous developer, all penetrants

D-72A I Form a NA YES Dry powder developer, all Type I penetrants

D-76B I Form b NA YES Aqueous soluble developer

D-78B I & II Form c NA YES Aqueous suspendable developer

D-702* II Form f NA NA Special high temperature developer

Met-L-Chek


7/42

7

Procedure of fluorescent penetrant inspection

System of the fluorescent penetrant testing

Present system correspond to requirements of world standards: MIL-I 25135E, MIL STD 6866, AMS 2644, EN 571-1. Allcomponents meet the European requirements on Health, Safety and Ergonomics. The inspection system is basically made ofstainless steel and equipped with first class means for functional control, delivered by producers like Siemens, Rittal,Weidmller, Festo, Sick, Balluf.

Basic phases of processing:

1. precleaning

2. wash3. dry to =1000C4. cooling to 400

5. immersion in a tank with penetrant6. water wash

7. immersion in a tank with emulsifier8. post water wash

9. dry in heater=600

C10. electrostatic application of powder developer11. inspection of the sample in a cabin at ultraviolet illumination

Precleaning

Drain

Penetration

Emulsification

Water wash

Wet development

Hot air dry

Inspection(20Lux; 1000W/cm2)

Hot air dry

Dry development Fast drying

development

Water removal Penetrant removal


8/42

8

Test panelsSensitivity of inspection media, quality of intermediate cleaning and control of the whole penetrant

process are determined on reference blocks, i.e. on metal panels with defined roughness and provided

with standardized artificial cracks(defects).

Test panel ASME V

Used for the testing of the penetrants indication sensitivity. Due to thedivision of the test panel into two parts, it is possible to compare 2 differentpenetrants.Present test panel is an aluminium plate (805010 mm), divided by a notch(5021,5 mm), into two parts. Because of a special thermal treatment

ASME panel, there is a uniform crack pattern, which is visible on both sidesof the test panel.

Indication of cracks by using of system

NORD-TEST (U87, Rot 3000, U89)

Test body 2 (EN ISO 3452-3)

The reference block 2 consists of an austenitic base plate, which is chromium-

plated on one side and provided with 4 different surface roughnesses on the otherside. 5 star-shaped crack patterns of different sizes are generated in the chromium-

plated side by applying a pressure load to the rear side with a ball. The rough areas

are used for control of the intermediate rinse step. The indication on the referenceblock gives no suggestion of the indication on the part under test. The user uses the

reference block for the control of inspection material. For checking the rinsability

of penetrants four adjacent areas sized 25 x 35 mm are placed on one half of thepanel with roughness of Ra = 2,5 m, Ra = 5 m, Ra = 10 m and Ra = 15 m. The

defect area is located on the other half of the test surface of the panel. The size ofeach defect is determined optically at its maximum diameter using calibrated scales

Reference block1 (EN ISO 3452-3)

The type 1 reference block consists of a set of 4 nickel-chrome plated panels with10, 20, 30 and 50 m thickness of plating respectively.

The 10, 20 and 30 m panels are used for determination of the sensitivity of

fluorescent penetrant systems.The sensitivity of colour contrast penetrant systems is determined by using the 30

and 50 m panels.

The type 1 panels are rectangular in shape with typical dimensions of 35 x 100 x 2mm Transverse cracks are made in each panel by stretching the panels in the

longitudinal direction. The width to depth ratio of each crack should be

approximately 1:20.

A declaration stating conformance to EN ISO 3452-3 and in line with EN 10204,

Type 3.1 B shall accompany each test block.

Test body JIS Z 2343

Used to determine the sensitivity of penetrant systems and for comparingtwo penetrants, one of which can be taken for standard. Consists of two testpanels which are bronze planes 100352 mm , covered with NiCr-layer. InNiCr-blanket. Crosscut cracks are made, depth of which fits the width of theNiCr-blanket. (Designed in 4 types 10, 20, 30 & 50 m). The quotient ofcracks width to their depth equals 1:20. Each test-panel has a certificateaccording to EN 10204, type 3.1 B, which verifies its aptitude to EN ISO3452-3. Test-panels with cracks width of 10 m, 20 m, 30 m used for afluorescent sensitivity testing penetrant systems. The sensitivity of contrastpenetrant systems is determined by means of panels, depth of cracks inwhich - 30 and 50 m.

Article No. 127.100.000

Article No. 127.550.000

Article No. 127.400.001

Article No. 127.600.001 - 10 mArticle No. 127.600.002 - 20 mArticle No. 127.600.003 - 30 mArticle No. 127.600.004 - 50 m


9/42

9

Article No. 127.700.004 Article No. 127.700.003

Article No. 127.700.002 WTP-2

Test panel WTP-1 & WTP-2Designed to evaluate removability of the fluorescent penetrant. PanelWTP-2 is a stainless steel panel, measuring 46 inches and 0,090 thickwith two parallel medium rough strips, each 61,5 inches, separatedby a smooth 1 inch strip. The panel is used to evaluate the quality ofremovability according to the requirements of MIL-STD-6866 & ASTM E-1417.

Test panel PSM-5Present test panel is used for testing the penetrant process in whole.Test-panel PSM-5 is rectangular,1015cm, width 2,3mm, made fromstainless steel.The chromium-plated strip on the side contains 5 crack patterns. Theraised, circular or star-shaped crack patterns are arranged according to

their sizes.The biggest defect becomes visual after low-sensitive penetrant`streatment. The smallest defect can hardly be seen even after application ofhighly sensitive penetrants. There are no two identical panels. The crackpattern differs from one panel to another. Test panel is designed in twomodels. Both models are designed in accordance with specification Pratt-Whitney P/N TAM 146040. The panel is not to be used for detecting thesensitivity of penetrants system.

Indication of cracks by use of FP903 & D70

KDS-Test panelTwin KDS Panel, with the cracked sections side by side, facilitate quick andaccurate determination of relative defect visibility.Twin KDS Panel, with the grit blasted sections side by side, makefluorescent background comparison simple.Twin KDS Panel comes in two models.Model WW for use with Method A water washable penetrants. Model PE foruse with Method B,C,D nonwater-washable penetrants.The difference between two models is in crack size. Model WW cracks rangefrom 1/22 1/6 inches while Model PE cracks range from 1/64 to1/11inches.

Twin KDS PE Twin KDS WW

Comparator UTE-3

Designed for right determination of ultraviolet radiation intensity at workplaceif using fluorescent penetrants.Used to compare size of pores and comparison board of optical probes withtext according to Jger 1 andJger 2.

Article No. 127.700.001 WTP - 1

Article No. 127.800.000

Article No. 127.850.000


10/42

10

Magnetic particle testing

The magnetic particle testing method (MT) is one of the most sensitive, reliable and productive NDT-method forsurface inspection of products from ferro-magnetic materials. The method is based on the attraction of ferro-magnetic particles by force of leakage flux like cracks, laps, leak of fusion, pores which appear above surfacedefects after adequate magnetization. MT can be used for surface defects (open to the surface) and under certain

conditions for detection of near-surface defects. Higher probability of detection is given, when the direction of adefect is perpendicular to the direction of the applied magnetic field. The smaller the angle between defect andfield direction the weaker the indication

Microscope imaging of cracks Cracks indication by fluorescentT method

Magnetic Particle testing is used in almost every industry branch:metallurgy, machine building, aircraft building, shipbuilding, during production in steelworks, at pipe

installation), electric power and chemical machine building, Means of transportation (aircrafts, rail cars,vehicles).Magnetic Particle testing procedure consists of the following: 1 Preparation of the items` surfaces of the testobjects for testing, 2 magnetization of the object, 3 application of magnetic particle suspension onto the testobject 4 Testing of the object, 5 demagnetization.

Circular, longitudinal and combined magnetization are used for MT. There are a lot of magnetization schemes,some of which are shown below.

Circular Longitudinal

Magnetic field direction10m


11/42

11

Article No.131.002.000

Hand magnetizing devices.

Specifications:

UM8 UM8/42*

UM15 UM15/42*KMU

8/42*

Permanent

magnetFlaw Finder

Article No. 131.002.001 132.002.000 131.010.000 131.010.001 131.015.100 131.001.010

Distance between poles (mm) 168 168 76-260 76-260 195 to 250

Pole cross section (mm) 27,5x22,5 27,5x22,5 27,5x22,5 27,5x22,5 27x27

32Dimensions LHmax (mm) 235x156 235x156 230x132-200 230x132-200 195x320 150 50

Tangential field strength

A/cm (DIN 54131-2)40 36 23 21 35 23

Standard length of the cable(m)

3 3 3 3 3

Supply voltage, V 230 42 230 42 2x42

Protection system IP65 IP65 IP65 IP65 IP65

Pull-off strength app.:EN ISO 9934-3:2002

17 kg 16 kg 7,5 kg 7,5 kg 16 kg 30 kg

Weight (kg) 3,4 3,4 3,8 3,8 11,0 1,0

*Additional transformer 230/42 V is necessary

UM8UM15

KMU 8/42 Flaw Finder

Article No.131.002.001Article No.131.010.000

Article No.131.001.010


12/42

12

Portable magnetizing devices

Specifications:

DIN 54131 & VDE Hellotest 10 Hellotest 20 Hellotest 40 Hellotest 60Article No. 131.020.100 131.020.300 131.050.005

Alternate currentMax. test current, measured via highcurrent 5 m cable.

Effective value A 1000 2000 2800 4200

Peak value A 1400 2800 4000 6000

Short-circuit A 3700 6900 8000 9000

Infinitely variable Main

Operating data

Source voltage V 230 400 400 400

Frequency Hz 50 50 50 50

Power input max. kVA 3 12 23 50

Open circuit voltage max. V 3,2 6 7,5 10,5

Control voltage V 15 15 15 15

Dimensions

Length mm 325 445 500 1200

Width mm 290 290630 630

Height mm 385 385 965 910

Weight kg 17 30 105 160


13/42

13

Stationary Magnetic Devices

Defectoscopes are designed and constructed due to client`s performance specification. As an example you cansee these two the most popular defectoscopes.

Demagnetizing devices

HETT 150/250/350/450/550

900-Universal WE II

Basic device for combined magnetization of items byalternate current.

Test detail length 900 mm

Test detail diameter 450 mm

Test detail mass 450 kgCircular magnetization current 2800 Longitudinal magnetization current 15000 tPower consumption 55 kVA

Air-operated clamp lead 7 mmSource voltage 3400 VLength 2200 mmHeight 2300 mmWidth 760 mmWeight 780 kg

ZER-O-MAT

Noncontact magnetization of the test objects. A specially designedU-like solenoid lets detect surface defects every direction oncylinder-like objects.

Demagnetization coils are designed for reducing the remanent magnetism of objects, magnetized duringpreceding MT.

150 250 350 450 550Magnetic field strength /cm 110 90 80 65 54

demagnetization window, mm 150 250 350 450 550


14/42

14

Coloured magnetic particles

For preparing a suspension on a water & oil base

Item Colour

Average

dimension

of the

grain (m)

Recommended

concentration (g)

Sedimentation

( 2 g/l)/100ml

BW333

black 4 3-5 0,1

WD105 grey-white 37 5 0,1

TGL

orangeorange 47 5 0,3

TGL11 brown 35 5 0,3

WW50 grey-white 30 5 0,25

TGL12 green 35 5 0,3

magnification:

140

175

175

175

175

630

.

Grain form Indication of artificial cracks on a

test body 1

*Wetting-, antifoam-, antirust-agentBC502 (30ml./1l.) isnecessary to prepare a suspension on a water base.

Article No. 135.001.520

Article No. 135.003.030

Article No. 135.001.510

Article No. 135.001.511

Article No. 135.001.530

Article No. 135.002.010


15/42

15

Fluorescent magnetic particles

Delivery:

1. Dry powders in 1kg container2. Concentrates (1:20, 1:50) on water base (cans 1; 10 l)3. Ready-to-use suspensions on oil base

magnification:

280

280

630

630

630

ItemFluorescence

coefficient

Gd/W

Average

grain size

(m)

Recommended

concentration (g)

Sedimentation

( 1 g/l)/100ml

MEF

8-TC1,7 2 0,6-1 0,15

LY

25002,8 4 0,4-1 0,3

LY

23003,4 6 0,4-1 0,25

LY

1500 5,2 12,5 0,6-1,5 0,2

CGY

400011,3 14 0,5-1,5 0,25

Article No. 135.001.008

Article No. 135.001.040

Article No. 135.001.150

Article No. 135.001.010

Article No. 135.001.180


16/42

16

Magnetic particle testing by means of aerosol system from the firm HELLING

quick and efficient handy and easy to use reliable estimation of defects high sensitivity

economic material consumption in accordance with ASME Code, Sect. V,

ASTM E 709:95, EN ISO 9934 doesnt contain CKW/FCKW

NRF 101Article No. 135.005.050

Luminescent magnetic suspension of ultra high sensitivity. Average grain dimension4 m. Form is ready for use. High-flash magnetic particle suspension in a slightlysmelling oil-carrier-fluid. It is a good corrosion inhibitor.

NR 104A

Article No. 135.006.020

White background paint. White pigmented suspension in a slightly volitilizablesolvent, doesnt contain chlorinated hydrocarbons. To be applied as thin layer with athickness up to 30 m.

NRS 103

Article No. 135.005.070

Black magnetic suspension of high sensitivity . Average grain dimension of 4 mHigh -flash magnetic particles suspension in a slightly smelling oil-carrier-fluid. It isa good corrosion inhibitor.

NR 107Article No. 135.006.050

Remover for background paint.

Additional products

Oil carrier fluid for preparing magnetic particle suspensions.

Specifications: Oil 4000

Inspection method Oil 4000

Density DIN 51 757 762

Kinematic viscosity in 20mm

2/s


2/s


2/s

DIN 51 562DIN 51 562DIN 51 562

2,01,61,4

Burning point DIN 51 758 >60

Chilling point DIN ISO 3016


17/42

17

Magnetic field strengthmeter MP-U, MPU-ST

Present device is designed for measuring the magnetic field strength (AC, DC) in range of 0 2 000 /m.

Liquid-crystal 3.5 digit display, indication of battery condition. The following probes are available: axial field

probe ( 6,0 mm); tangential field probe ( 1,6 mm); flexible sensor( 0,7 mm).

Bulb for sedimentation control Hydraulic pump atomizer

PROFI

Specifications: MP-U MPU-ST

Measuring range0-200 /cm;

0-2000 /cm

0-200/cm;

0-2000 /cm

0-20000 /cm

Unit measure /cm; Oe

Indication Liquid-crystal 3.5 discharge display

Error 2%

Power supply 9 V (ICE 6 LF 22)

Memory2000

measurements

Interface device RS 232 (V.24)

Dimensions, mm 1608027

Weight, g 250

Designed to detect suspension quality. Determines themagnetic powder concentration in suspension.Corresponds to standards: ASME V, ASTM E 709,1444

Used for magnetic powder sputtering suspensions, andalso for colored and fluorescent penetrants. Operatingpressure 4 bar, container volume 1,5 l, max. filling volume1,3 l.

Article No. 133.005.010

Article No. 126.400.000Article No. 134.005.000


18/42

18

Reference Blocks/Field Indicators

Magnetic field direction

Magnetic field direction

Reference block 2 (EN ISO 9934-2)Reference block is a self contained unit requiring no external magnetic fieldinduction. Used to determine the quality of the magnetic particlesuspensions. The block consists of 2 soft iron bars, separated by a thin(15m) Al-foil, representing an artificial defect. Permanent magnets are seton the sample ends. Because of the permanent magnetic field the bars getmagnetized and magnetic particles accumulate over the artificial defect,forming indicator lines. The quality of the suspension or dry powder isestimated over the summarized the length of the lines.

Specifications:Dimensions (LWH): 1554012 mmTangential component of magnetic fieldover the artificial defect at points G (-4): -1/m

(4): 1/cm

Reference block 1 (EN ISO 9934-2)The reference block is a disc with 2 types of natural cracks on the surface.Coarse cracks are the result of the polishing, fine cracks are the result ofstress corrosion. The block is permanently magnetized by centralconductor through the hole. Estimation of magnetic particle suspensions ismade by visual or other appropriated method of comparison of theindications.

Specifications:Sample diameter: 50 mmSample height: 10 mmThe width of cracks: 2-10 m

Field Indicator according to BertholdDesigned to determine the strength and direction of the selectedmagnetizing setup and the quality of magnetic powder suspension.

Specifications:Sample diameter: 20 mmSample height: 5 mmHolder length: 95 mmWeight: 24 g.

Magnetic Field Indicator D 250 (ASME-V)The magnetic field indicator type D 250 is designed in accordance with thefollowing specification methods of non destructive testing :MIL-STD-271 E, 4.3.2.5.5, figure 8NAVSHIPS 250-1500-1, 12.4.1.5, figure 12 17

ASME, section V, Art. 25, SA-275, figure 8The sample is used for localization of magnetic fields and their directionsduring performance of magnetic particle testing.

Specifications:Sample diameter: 27 mmSample height: 4 mmHolder length: 100 mmWeight: 42 g.

Ketos Ring (ASTM E 1444-01)The sample is designed to determine the defectoscope working capacityand the quality of magnetic powder suspension. The sample representsitself a 7/8"(22,2mm)-wide disk. Outer diameter 5"(127mm), inner diameter1,25"(31,75mm) - made from steel AISI 01.12 holes (diameter 0,07" (1,78mm) are placed on different distances fromthe outer cylindrical surface. When current (FWDC or HWDC) is passedthrough the central conductor, (conductor diameter 1 3/16 , conductor

length mustnt be less then 400mm), waste fields appear, decreasing asthe distance from the hole to the outer cylindrical surface increases. Whenthe magnetic suspension is applied on the disk, magnetic powderaccumulates over the cylindrical surface holes, forming indicator lines.The process, corresponding to the recovery of the majority of lines isaccepted as optimal.

Article No. 134.002.100

Article No. 134.002.002

Article No. 134.003.000

Article No. 134.003.100

Article No. 134.004.000


19/42

19

Roughness standard test block enclosed

Hardness standard test block enclosed

Test-kit E 100 forTConsists of accessories, necessary for the MP:

Magnetic field strength meter MPU

UV-intensity measuring device Reference block 1

Reference block 2

Package of detectors Burmah-Castrol TypeI or TypeII

Field Indicator according to Berthold

Bulb for sedimentation control

Gelatine film for documentation (10 documentation cards)

Surface Roughness TesterTR100Determination of surface roughness quickly and qualitatively (Ra;Rz)

Specifications: Tracing length: 6 mm

Speed: 1 mm/

Cut-off length: 0,25/0,8/2,5 mm

Effective range: Ra:0,05-10,0 m

Rz:0,1-50,0 m Error: 15%

Measuring tip: diamond, R 5,0 m

Dimensions: 1257326 mm

Weight: 200 g

Portable Hardness Tester-1000Dynamic hardness tester with digital display for hardnessmeasurement of any item easily and quickly.

Specifications:

Unit measure: Leeb (HL); Vickers(HV); Brinell (HB); Rockwell B(HRB); Rockwell C (HRC); Shore D (HSD)

Effective range: 200-900 HL

Error: 0,5%

Angle of measurement:

Dimensions: 165x28x28mm

Article No. 134.001.100

Article No. 150.500.100

Article No. 710.010.001


20/42

20

Ultraviolet sources

Stationary ultraviolet lamps

ZERO-400 IP-20

ZERO-400 IP-54

ZERO-800 IP-54

Specifications: ZERO-400IP-20

ZERO-400IP-54

ZERO-800IP-54

Article No. 144.000.404 144.000.403 144.000.801

Input voltage 230 V; 50/60 Hz

Starting current 5 A 10 A

Starting time Less then 5 min

Restarting time Less then 10 min

Ultraviolet radiant 400 2 400

Wave length of UV light 365 nm

Ultraviolet intensity on distance 400 mm 5000 11000

Lifespan of UV source about 1500 hours

Dimensions 500500300

Weight 30 kg 40 kg

Protection class IP20 IP 54

-30-25-20-15-10 -5 0 5 1015

2025

30

1000

2000

3000

4000

5000

6000

7000

8000

9000

-25-20

-15-10

-50

510

1520

25Bestrahlun

gsstrke(W/cm

2)

YAx

is(cm)

XAxis(cm)

Ultraviolet radiation distribution (W/cm2)

of Zero 400

200 220 240 260 280

300

320

340

360 380 400

0

100

200

300

400

500

600

700

800

Helling Zero

(nm)

UVC UVB

Ultraviolet radiation spectral distribution of

Zero 400

Intensity


21/42

21

Handheld ultraviolet lamps

Specifications: Super UV 2005 C 10 A-HE C 10 A-SH C 10 A-SArticle No. 142.000.105 142.000.200 142.000.300 142.000.110

Input voltage 230 V; 50/60 Hz

Starting current 1,60 A 1,85 A 1,85 A 1,85 A

Starting time Less then 5 min

Restarting time Less then 10 min

Ultraviolet radiant HN100

Wave length of UV light 365 nm

Half-width value of UV emission 1,5 nm

Ultraviolet intensity on distance 400 mm 10000 4000 10000 4000

Lifespan of UV source about 1500 hours

Dimensions 20010080 mm 280280140

Weight 5 kg 7,5 kgProtection class IP20

Super UV 2005

C 10 A-HE

C 10 A-SH

C 10 A-S

UVC UVB UVA

200 220 240 260 280 300 320 340 360 380 4000

500

1000

1500

2000

2500

3000

3500

4000

4500

(nm)Ultraviolet radiation spectral distribution

-12-10

-8-6

-4-2

02

46

810

12

0

500

1000

1500

2000

2500

3000

3500

-14-12

-10-8

-6-4

-20

24

68

1012

14

Bestrahlungsstrke(W/cm2)

YAx

is(cm

)

XAxis(cm)

Ultraviolet radiation distribution

0 10 20 30 40 50 60 70 80 90 100 110 1200.01

0.1

1

10

100

1000

t (min.)

Ultraviolet radiation constancy

W/(cm

2nm)


22/42

22

Ultraviolet-LED lamps

Achieved-Change of Generation for handheld lamps!

Specifications:

iAlso available with power supply,

iiPermanent use is possible,

UV-EndoskopUV-Inspector

365-LWGUV-

Inspector 380-RUV-Inspector 365 UV-Inspector 2000

iUV-Inspector 3000

i

Ar ticle No. 142.300.001 142.200.311 142.200.101 142.200.301 142.200.411 142.200.511

Voltage 4,8 V (4x accum) 18 V 24 V

UV-light sour ce 1xUV-LED 1xUV-LED 1xUV-LED 1xUV-LED 4xUV-LED 9xUV-LED

Lifetim e the UV-LED (h.)

approx. 10 000

UV-light intensity(W/cm

2)

6000 at 20mm10000 at50 mm

2000 at 200 mm 3000 at 400 mm 2500 at 400 mm 4000 at 400 mm

Wavelength(nm) 365 365 365 365 365 370

Emission half-width (nm)

8,5 8,5 8,5 8,5 8,5 8,5

Working hours (H) approx. 6ii

approx. 6ii

approx. 4,5ii

approx. 4ii

approx. 4ii

Weight(g.) approx. 550 approx. 550 approx. 250 approx. 300 approx. 1300 approx. 1400

Dimensions (mm) 1000x6 2000x5 170x45 170x45 75x320x110 230x130

Advantages of ultraviolet-LED sources:

High efficiency at low power consumption

Low heat generation

Very long lifetime

Rigid against shock and vibration

Defined wavelength of emission

Safety due to protective low Voltage

Immediately ready for use after switch on

UV-Endoscope

UV-Inspector 365-LWG

UV-Inspector 380

UV-Inspector 365UV-Inspector 2000 UV-Inspector 3000-N


23/42

23

Leak inspection

Bubble methodThe essential matter of the method is as follows:

Registration of local leakages in an under-test item by appearing of indicator gas bubbles in indicator liquid(indicator cover). The method is used for testing the impermeability of reservoirs welded joint, fluid power andgas systems under the overpressure,(which can be created by vacuum pump).Foam-film indicator(Proof Check) is applied on the under-test joint weld and overpressure is generated. Air(check gas), penetrating through the joint weld microflaws, impacts mechanically on foam-film indicator,accumulating on the defective place, deforms it. In this case bubbles or foam swelling can be seen .

Specifications: EV20:

Evacuation rate: 4m3/hour

Vacuum: 800 mbar

Dimensions: 280290225 mmWeight: 10,5 kg

Voltage: 220-230 V (50Hz)

Protection class: IP54

Foam-film indicator Proof Check

and leak indicationVacuum pumpEV 20 for pressure gradient origination

Vacuum rames o di erent con idurations or testin the oint welds im ermeabilit

D

(D: 251200 mm) 600100 mm 600100 mm 300 mm



24/42

24

Hydrogen leak detectorsThe concept of catalitically selective estimation of hydrogen by a special semiconductor sensor is a basis of the

leak detector Mixture of nitrogen (95 %) and hydrogen (5%) is used as an indicator gas. This mixture isntflammable (ISO 10156 )is not toxic or corrosive, nor dangerous to the environment

H1000 9012XRS

Specifications: H1000 9012XRSMinimum detectable concentration of hydrogen 0,5 ppm

Minimum detectable leak of hydrogen 5 10-5 mbar l/s

Reaction time for hydrogen 2sec.

Self-test procedure and warm-up time 1min.

Supply 100-230 V

Continuous work time from accumulator 13 hours

Dimensions 275 155 170 mm 250 120 85 mm

Weight 3 kg 1,9 kg

Helium leak detector PDH-4

The basis of the detector is so called Selective Ion Pump Detector SIPD. Principe of the work is asfollowing: helium is heated up to a certain temperature, penetrates special quartz membrane (which ispermeable only for helium atom). Detector senses helium and sends a signal, which force is proportional to thequantity of helium, having penetrated through the quartz membrane. Signal amplitude represents the size of leak.

Specifications:PDH-4:Minimum detectable concentration of He 2 ppm

Minimum detectable He leak 5 10-7 Pa m3/s

Reaction time for He 2 sec.

Self-test procedure and warm-up time 3 minutes

Supply 18 V, Accumulator

Continuous work time from accumulator 4 hours

Operating conditions

Temperature

Relative humidity

+5 35

90% maximumDimensions 170 136 290 mm

Weight 2,6 kg

Portability High sensitivity Hugh selectivity Easy to use High robustness


25/42

25

Ultrasonic leak detector Hellophone

Leak detectorHellophonedesigned for:Detection of compressed gas, liquid (also viscous) leaks from small holes (flute cracks) in pipeline and

reservoirs

Testing of stop valve (cocks, clappers etc.) in operating objects Compression and joint weld leak testing (if using ultrasonic generator)

Detection of minor electrical discharge in defective contacts of electric installations.

Delivery kit:Ultrasonic device with accumulator power supplyUltrasonic generator

ChargerEarphonesWaterproof probing device for solid bodySolid state probeAir-ultrasonic probe

HellophoneSpecifications: Measuring frequency: 40 Hz1Hz

Digital display LCD

Conservation of max- quantity

Integral accumulator (10 hours of work)

Dimensions: 1206525 (generator)19510040 (receiver)

Weight of the package with the bag: 3,6kg



26/42

26

Fluorescent concentrate for detecting leaks in cooling systems etc.

Luminescent leak testing method is based on the use of special agents (as test medium) - luminophors, whichare emitting visible light under ultraviolet radiation. The location of a leakage is detected by this specificlight emission.

H 800Oil-suspendible concentrate

for detecting leaks in cooling

systems:

flammable oiling materials

synthetic and mineral oils

Consumption: 0,5-2ml/l

Optimum wave length

excitation: 365nm

Color under UV excitation: yellow

H 849Concentrate on water basis with emulsifying additive

and corrosion inhibitor for detecting leaks in cooling

systems, leak testing of different objects

Consumption: 2-5 ml/lOptimum wave length excitation: 365nm

Color under UV excitation: green

Article No. 616.000.033 0,5 LitreArticle No. 616.000.034 1,0 LitreArticle No. 616.000.032 10,0 Litre

Article No. 616.000.035 20,0 kg barrel

Article No. 616.100.103


27/42

27


Radiographic film

*Hand developing by use of Fuji-Chemicals at 20C and 5 min developing time**

Machine developing by use of Agfa-Chemicals at 28C and 8 min developing time

Helling GmbH officialdistributor of Fuji Industrial

X-RAY Products

IX 50

An ultra-fine grain, high contrast ASTM Class I film having excellent sharpness and high discrimination characteristics. Itis suitable for use with any low atomic number material where fine image detail is imperative. Its ultra-fine grain makes ituseful in high energy, low subject contrast applications where high curie isotopes or high output X-ray machines permit itsuse. Wide exposure latitude has been demonstrated in high subject contrast applications.IX50 is generally used in directexposure techniques or with lead screens.

IX 80An extremely fine grain, high contrast ASTM Class Ifilm suitable for detection of minute defects. It is applicable to theinspection of low atomic number materials with low kilovoltage X-ray sources as well as inspection of higher atomicnumber materials with high kilovoltage X-ray or gamma ray sources. Wide exposure latitude has been demonstrated inhigh subject contrast applications. IX80 is generally used in direct exposure techniques or with lead screens.

IX 100A very fine grain, high contrast ASTM Class II film suitable for the inspection of light metals with low activity radiationsources and for inspection of thick, higher density specimens with high kilovoltage X-ray or gamma ray sources. Wideexposure latitude has been demonstrated in high contrast subject applications. Although IX100 is generally used in directexposure techniques or with lead screens, it is suitable for use with fluorescent or fluorometallic screens.

IX 150A high speed, fine grain, high contrast ASTM Class III film suitable for inspection of a large variety of specimens with low-to-high kilovoltage X-ray and gamma ray sources. It is particularly useful when gamma ray sources of high activity areunavailable or when very thick specimens are to be inspected. It is also useful in X-ray diffraction work. IX150 is used indirect exposure techniques or with lead screens.

FUJI IX AGFA KODAKFilm category Sensitivity, R-1

IX 50 D 2 M 100 C 2 2,7

IX 80 D 4 M 125 C 3 4,5

IX 100* D 5 T 200 C 4 6,7

IX 100** D 7 AA 400 C 5 11,0

IX 150 D 8 CX C 6 17,0


28/42

28

Format cm Film type

NIF non interleaved package, 100 sheets10 x 24 IX 50, IX 80, IX 100, IX 150

10 x 48 IX 50, IX 80, IX 100, IX 150

13 x 18 IX 80, IX 100, IX 150

24 x 30 IX 50, IX 80, IX 100, IX 150

30 x 40 IX 50, IX 80, IX 100, IX 150

NIF - non interleaved package, roll package (4 items)70 mm 168 m IX 100

EPAK vacuum package with layers, without Pb screen, 50 sheets6 x 24 IX 80, IX 1006 x 48 IX 80, IX 100

10 x 24 IX 50, IX 80, IX 100

10 x 40 IX 80

10 x 48 IX 50, IX 80, IX 100

18 x 24 IX 80

24 x 30 IX 80

30 x 40 IX 80

EPAK - vacuum package with layers, without Pb screen, roll package (2items)

60 mm 61 m IX 80100 mm 61 m IX 80

EPPB vacuum package with Pb screen, 50 sheets6 x 24 IX 50, IX 80, IX 100

6 x 48 IX 50, IX 80, IX 100

10 x 24 IX 50, IX 80, IX 100

10 x 40 IX 50, IX 80, IX 100

10 x 48 IX 50, IX 80, IX 100

18 x 24 IX 50, IX 80, IX 100

24 x 30 IX 50, IX 80, IX 100

30 x 40 IX 50, IX 80, IX 100

EPPB - vacuum package with Pb screen, roll package (2 items.)60 mm 61 m IX 50, IX 80, IX 100

70 mm 61 m IX 50, IX 80, IX 100

100 mm 61 m IX 50, IX 80, IX 100

Chemical agents for processing radiographic film Fuji

Developer Rendol 4 5 l ready to use liquor for hand development

Fixing solution M-FIX 25 l ready to use liquor for hand development

Developer Audel 2 20 l ready to use liquor for automatic

development

Fixing solution AUFIX 2 20 l ready to use liquor for automaticdevelopment


29/42

29

Developing machines for radiographic film

Characteristic data Colenta FNDX1 Article No. 232.010.001Film type Sheet and roll films

Max. film width 36 cm

Development time Controlled from 3 to 13 minutes

Development rate at 8 min. 16 films/hour, Format3543mm

Development temperature Regulated from 18 to 43C

Drying temperature Max. 60C, hot air

Regeneration system Automatic

Capacity charge2,6 l of developer2,5 l of fixer , 3 l of water

Water consumption while working 1,5 l

Water connection 3/4" (3-10 bar)

Supply 220-240 V, 16 , 50-60 Hz

Power consumption 1,7 W, Stand-By (0,35 kW)

Weight 58 kg

Characteristic data Colenta FNDX2Film type Sheet and roll films

Max. film width 43 cm


Development rate at 8 min. 29 films/hour Format 3543mm

Development temperature Regulated from 18 to 43C



Capacity charge6 l of developer,6 of fixer, 6 l of water



Supply 220-240 V, 16 , 50-60 Hz

Power consumption 3,1 W, Stand-By (0,6 W)

Weight 127 kg

Characteristic data Colenta FNDX3Film type Sheet and roll films

Max. Film width 43 cm


Development rate at 8 min. 38 films/hour Format3543mm

Development temperature Regulated from 18 to43C



Capacity charge9 of developer,8 l of fixer, 8 l of water



Supply 220-240 V, 16 , 50-60 Hz

Power consumption 3,5 W, Stand-By (0,6 W)

Weight 132 kg


30/42

30

Accessories

Film viewing equipment

Densitometer

Sensitivity standards

Darkroom accessories

Absorbance standard

Packages of lead letters and numbers

Article No. 242.004.000


31/42

31

Ultrasonic testing

Wall thickness measuring device

HELLISON-1

Ultrasonic defectoscope

HELLSTEIN II

Ultrasonic defectoscope

INT-Bond-Tester

Tested materials: Black and nonferrous metals,

hard plastics, glass, ceramics

Effective range: 1-300 mm

Definition: 0,1 mm

Error: 0,5%Ultrasonic transducers: 2; 5: 10 Hz

In-steel calibration

Power Supply: 2,4 V, 2 from AccumulatorDimensions: 1256530 mm

Weight: 200 g

Delivery: ultrasonic thickness indicator, ultrasonic transducer2 Hz, ultrasonic gel 250 ml, charging device.

Detection of defects as homogeneity disfunction in welds,

preformed materials and finished materials. Depth determination

and defects coordinates.

Test range 10-5000mm (in steel)

Velocity range: 1000-9999 m/sGain: 140 dB

Frequency range: 0,5-15Hz

Interface RS232Power Supply: 14 V, Li-AccumDimensions: 15225570 mmWeight: 2,3 kg

Ultrasonic resonance spectroscopy (URS) utilizes information in the

frequency domain obtained due to the constructive and destructiveinterference of elastic waves for nondestructive evaluation of

inspected objects. In a resonance test an ultrasonic tone-burst with

sweeping frequency is applied to an ultrasonic transducer and aresonance spectrum of the inspected structure is acquired. The

acquired spectrum contains information about the properties of

materials used for the structure and flaws that may be present in it.

Measurement setup: Narrowband ultrasonic spectroscopy can be

used for the NDT of aerospace multi-layered structures. The INT-Bond-Tester used for this test operate on the principle of exciting a

mechanical resonance in a multi-layered structure. A piezoelectric

probe, excited by a swept frequency signal is coupled to the surface

of the inspected structure using a coupling agent. The instrumentacquires probes frequency spectrum in the range of some tens of

kHz to several hundreds of kHz. A resonance in the layered structure

occurs when echoes between two boundaries travel back and forth

due to the difference in acoustic impedances at the boundaries.

Article No. 311.000.100

Article No. 311.001.001


32/42


33/42

33

Sample

Sample

Current meter (AC, DC)

High quality steel feeler 0,05-1mm

Pocket lamp

Pocket lens(magnification 3, 6, 9)

Article No. 810.070.002 Article No. 810.080.038

Article No. 810.070.005

Article No. 810.080.039

Article No. 810.080.008

Article No. 220.026.300

Article No. 810.080.009

Article No. 810.080.042


34/42

34

h

Telescopic magnet

Joint weld master made of high quality steel

Thermometer(-70-+1000C)

Depth Gauge

Article No. 810.070.003

Article No. 810.080.003

Article No. 810.080.047

Article No. 810.080.017


35/42

35

Temperature indicators

Surface temperature detection

easy to use, quick and durable

precise (1% fromrated temperature)

temperature range from 38C to 1371C

Surface temperature detection

Self-adhersice labels

easy to use, quick and durable

precise (2% from rated temperature)

temperature range from 38C to 260C

High temperature paint

for surfaces protection, undergoing hightemperature impact

temperature range :up to1093C

Article No. 510.100.000

Article No. 510.200.000

Article No. 518.000.007


36/42

36

HELLING DYKEMTEXPENAND HELLING DYKEMDALOMARKERThe HELLING DYKEM

TEXPEN

stands out for its distinctive fine,

medium and bold oil-based paint markings. Its stainless steel

ball valve action tip writes through oil, grease and underwater without losing legibility or brightness even in extreme weatherconditions.The HELLING DYKEM

DALO

Marker is a marking pen with medium, and bold tips that hold a high capacity of oil-based paint

and it is a larger version of the HELLING DYKEMTEXPEN

.

Benefits:

Write sharp, defined, bright marks on almost any surfaceincluding metal, plastic, glass, concrete, rubber and more

Ergonomically correct marker that enables you to markat all angles, even upside down

Marker retains its shape

Paint flow is controlled by the bulb at the end of the barrel

Drying time: 25-35 minutes

DYKEMTEXPEN colours available

Fine Medium Broad

810.016.030 810.016.020 810.016.033 810.016.023 810.016.034 810.016.024

810.016.010 810.016.080 810.016.013 810.016.083 810.016.014 810.016.084

810.016.040 810.016.060 810.016.043 810.016.063 810.016.044 810.016.064

810.016.100 810.016.103 810.016.104

DYKEMDALO colours available

Medium Broad

810.026.033 810.026.023 810.026.034 810.026.024

810.026.013 810.026.083 810.026.014 810.026.084

810.026.043 810.026.063 810.026.044 810.026.064

810.026.103 810.026.104

HELLING DYKEMBRITE-MARKThe HELLING DYKEM

BRITE-MARK

is a general purpose marker that writes on almost any surface and features different tip

sizes for clear, bold markings. Its quick drying, oil-based paint withstands indoor and outdoor conditions, including acid andalkaline rain without fading, chipping or losing opacity. The HELLING DYKEM

BRITE-MARK

pens can be used to permanently

identify inventory, assemblies, tools, finished products or working-in-progress while resisting most work related abuses orcompounds.

Benefits:

Makes permanent, bright marks on metal, rubber, plastic, glass, concrete,leather, stone, wood, vinyl and more

Valve action mechanism prevents paint in barrel from drying when cap is left off

Threaded end of The HELLING DYKEMBRITE-MARK

40 can be screwed

into a jig or apparatus for continuous identification application Heavy-duty aluminium body

Ideal for colour coding

Bullet tips are replaceable

Drying time: 25-35 seconds

DYKEMBRITE-MARK colours available

Medium Broad 40

810.041.003 810.041.045 810.084.002 810.084.019 810.084.009 810.D40.003 810.D40.045

810.041.001 810.041.002 810.084.001 810.084.006 810.084.006 810.D40.001 810.D40.002

810.041.004 810.041.016 810.084.007 810.084.050 810.016.044 810.D40.004 810.D40.016

810.041.014 810.041.008 810.084.051 810.084.003 810.D40.014 810.D40.008

810.041.010 810.041.006 810.084.005 810.084.004 810.016.104 810.D40.010 810.D40.006

BRITE-MARK Fine

BRITE-MARK Medium

BRITE-MARK 40


37/42

37

HELLING DYKEMRINZ OFFTM and The HELLING DYKEMSUDZ OFFTMThe HELLING DYKEM

RINZ OFF

TMand The HELLING DYKEM

SUDZ OFF

TMwater removable ink marker and the HELLING

DYKEMSUDZ OFF

TMdetergent removable ink marker write on non-treated, non-painted metal, glass, ceramic and some plastic

surfaces and can be removed, leaving no ghosting. The markers feature a fibre tip ink pen that can be used indoors and

outdoors on any smooth nonporous surface and will not react with paint systems (should be tested for suitability). The HELLINGDYKEM

RINZ OFF

TMcan be removed with water while the HELLING DYKEM

SUDZ OFF

TMcan be removed with detergent.

DYKEMRINZ OFF DYKEMSUDZ OFF

Medium Broad Medium Broad

810.091.109 810.044.109 810.091.985 810.091.146 810.044.985 810.044.146810.06.024

810.091.105 810.044.105 810.091.938 810.091.694 810.044.938 810.044.69410.016.084

810.091.108 810.044.108 810.091.371 810.016.063 810.044.371

810.091.106 810.044.106 810.091.939 10.01 6.104 810.044.939

HELLING ACTION MARKERThe HELLING ACTION MARKER

44 and the HELLING ACTION MARKER

Fine Line are dye-based ink pens with a valve

action fibre tip that writes on any smooth surface. The HELLING ACTION MARKER

44 has a threaded end that can bescrewed into a jig or apparatus for continuous identification application. It is used to make broad markings on any smoothsurface, The HELLING ACTION MARKER

Fine Line is lightweight and writes fine, distinctive markings. Both markers feature a

clip to secure the pen in your pocket or on your clipboard.

Benefits:

Permanent ink writes on smooth surfaces such as metal, aluminium, plastic,glass, rubber and more

Inks are able to withstand oil, dirt, grease and extreme weather conditions

Interchangeable and replaceable tips are available

6 to 8 times the writing life of most other capillary markers of comparable size

Drying time: 45 seconds to 1 minute

Colours available

AM 44 Fine Liner

810.044.003 810.044.010 810.033.003 810.033.010

810.044.001 810.044.002 810.033.001 810.033.002

810.044.004 810.033.004

Fine Liner

AM 44


38/42

38

HELLING HIGH TEMPERATURE MARKERS

The HELLING TEXPEN

for high temperatures has a stainless steel-ball valve action tip and heavy viscosity, oil-based paintthat is specially formulated for nonporous surfaces that reach temperatures of up to 2000F/1093C. Marks become permanentand fused when heated. The marker is an ergonomically correct pen that enables you to mark at all angles, even upside down.The bulb at the end of the barrel controls paint flow.

The HELLING ACTION MARKER

44 and HELLING ACTION MARKER

33 for high temperatures are pigmented, oil-basedfibre tip pens that are specially formulated for nonporous surfaces that can reach temperatures up to 2000F/1093C. Marksbecome permanent and fused when heated. Both markers feature a clip to secure the pen in your pocket or on your clipboard.The HELLING ACTION MARKER

44 has an extra large paint capacity. The EHELLING ACTION MARKER

33 is lightweight

and writes fine, distinctive markings.

HELLING ACTION MARKER TEXPEN

colours available

Fine Medium Broad Range of Temperature

810.017.030 810.017.033 810.017.034 1093C / 2000F

810.017.010 810.017.013 810.017.014 1093C / 2000F

810.017.040 810.017.043 810.017.044 1093C / 2000F

810.017.100 810.017.103 810.017.104 426-482C / 800-900F

810.017.020 810.017.023 810.017.024 426-482C / 800-900F

810.017.080 810.017.083 810.017.084 426-482C / 800-900F

810.017.060 810.017.063 810.017.064 426-482C / 800-900F

HELLING ACTION MARKERcolours available

AM3 33 AM 44 Range of Temperature

810.033.250 810.044.250 1093C / 2000F

810.033.094 810.044.094 1093C / 2000F

810.033.266 810.044.266 982C / 1800F

810.033.219 810.044.219 843-899C / 1550-1650F

810.033.424 810.044.424 426-482C / 800-900F


39/42

39

HELLING HIGH PURITY MARKERS

The high purity HELLING TEXPEN

contains trace amounts of halogens, low melting metals and is low in chlorides. Therefore,its stainless steel ball valve tip can be used on surfaces where degradation, contamination or adverse effects are not desired.The high purity HELLING TEXPEN

is an ergonomically correct marker that enables you to mark at all angles, even upside

down. Its oil-based paint withstands extreme weather conditions.

The high purity HELLING ACTION MARKER

44 and HELLINGACTION MARKER

33 are dye and pigment based ink pens with a

valve action fibre tip that write on smooth surfaces. They are verylow in chlorides, so they can be used on surfaces wheredegradation, contamination or adverse effects are not desired. Pensmeet or exceed the requirements of the US Energy Research &Development Administrations Nuclear Grade for black, red, yellowand white inks. The HELLING ACTION MARKER

44 has a

threaded end that can be screwed into a jig or apparatus forcontinuous identification application. The HELLING ACTION MARKER

33 is light weight and writes fine, distinctive markings.

Both markers feature a clip on the pen cap that fits easily into your pocket or on your clipboard.

HELLING TEXPEN colours available

Fine Medium Broad

810.017.470 810.014.100 810.017.473 810.014.103 810.017.474 810.014.104

810.014.210 810.017.460 810.014.213 810.017.463 810.014.214 810.017.464

810.010.350 810.014.140 810.010.353 810.014.143 810.010.354 810.014.144

810.014.200 810.014.203 810.014.204

HELLING ACTION MARKER 44 and HELLING ACTION MARKER 33 colours available

AM 44 AM 33

810.044.404 810.044.729 810.033.404 810.033.729

810.044.534 810.044.916 810.033.534 810.033.916

810.044.301 810.033.301


40/42

40

Delivery program

Penetrant testing

Met-L-Chek / Dub-L-Chek , Standard Chek, Nord-Test,test equipment

Contrast and fluorescent systems

Electrostatic, penetrant and other coating systems

Control devices, UV examination lamps, UV measuring instruments

Magnetic powder testing

Magnetizing devices/test benches

Stationary defectoscopes

Colored and fluorescent magnetic powders

Test bodies

Leak testing

Helium and hydrogen leak detectors

Ultrasonic leak detectors

Vacuum testers with test frames

Colored and fluorescent concentrations


Mobile and stationary X-ray equipment and laboratories.

Radiographic accessories, radiographic films, darkroom accessories

Film viewing equipment, film development systems Radiation, measuring and alarm systems

Visual inspection

Rigid and flexible endoscopes

TV camera system

Mirrors, light probes and magnifiers

Ultrasonic testing Wall thickness measuring systems

Ultrasonic defectoscopes

Material test equipment

Control devices and accessories

Thermal inspection

Heat-sensitive crayons, lacquers, labels, inkfrom 38 C to 1371 C

Pyrometer


41/42

41

For Your Notes:


42/42

02.08.2007

Date post:	03-Apr-2018
Category:	Documents
Upload:	suphi-yueksel
View:	228 times
Download:	0 times

Helling Engl KATALOG

Documents