Since 1976
(Z660)www.texmate.com
HIGH ACCURACYLEGENDARY RELIABILITY
FAST DELIVERYFRIENDLY APPLICATION SUPPORT
POWER TRANSDUCERS
APR-17, 2017
Since 1976
(Z670)www.texmate.com 2
Model# Input signal Maximum Range Accu-
TT-1S1MTTM-2S2MMTTM-2S2MCTT-2D2MMTT-2D2MC
Thermocouple J -50 to 1000°C (-58 to 1832°F) ±1°C
Thermocouple K -50 to 1370°C (-58 to 2498°F) ±1°C
Thermocouple T -270 to 400°C (-454 to 752°F) ±1°C
Thermocouple E -50 to 700°C (-58 to 1292°F) ±1°C
Thermocouple B 0 to 1750°C (32 to 3182°F) ±2°C *
Thermocouple R -50 to 1750°C (-58 to 3182°F) ±2°C
Thermocouple S -50 to 1750°C (-58 to 3182°F) ±2°C
Thermocouple N -50 to 1300°C (-58 to 2372°F) ±2°C
Thermocouple C -50 to 1800°C (-58 to 3272°F) ±2°C
Pt100 -200 to 600°C (-328 to ±0.2°C
MV -60mV to 60mV
Voltage -10 to 10Vdc ±1mV
Current 0 to 24mAdc ±10μA
LEOPARD TL SERIESTT SERIES
Remote Display Programmer
Isolated Analog Output
Leopard Transmitter
Power
Relay Output Input Signal
Output signal : DC 4/0~20mA or DC 0~10VOutput resolution : 0.6uA.Output response time : <200mS.Communication : Modbus RS-485 RTU protocol, 4800~38400 bpsPower supply : 18~36 Vdc, internal protection against polarity inversion
*Accuracy is not guaranteed between 0 and 400°C (0 and 752°F) for type B, R and S.
TT-1S1M Single Channel input and Single 4-20mA output
TTM-2S2MM Dual same signal Inputs; Single 4-20mA output and Single 4-20mA output with Math Function
TTM-2S2MC Dual same signal Inputs; Single 4-20mA output with math function & Single RS-485 output
TT-2D2MM Dual Inputs; Dual 4-20mA output
TT-2D2MC Dual Inputs; Single 4-20mA & Single RS-485 output
4 Active, isolated analog output. (No need of external 24V to power output)
4 Plug n Play. Order unit setup to your exact requirements.
4 Dual 9A Form C relays with NO and NC connections available.
4 24 VDC Excitation to power 4-20 mA loops and selectable 5 or 10 VDC to power Strain gauge, and Pressure / Load cell.
4 Auto sensing AC/DC power supply 85-265 VAC / 95-370 VDC or optional 18-36 VAC / 9-60 VDC.
4 Remote programmer may be used as a remote display.
Available Inputs: 4 DC - Volts, Amps, mV, mA4 AC - Volts, Amps, mV, mA,
Line Frequency4 Load Cell, Pressure, Strain
Gauge4 3 wire Potentiometer -
Position, Resistance4 Temperature - Thermocouple,
RTD Pt-1004 Proximity switch - RPM or
Frequency
E469078
Texmate DIN Rail Mount Transmitters
Transmitters can be configurated using TT Configurator software without connecting to a power source.
Since 1976
(Z670)www.texmate.com 3
Contents
TA-1 & TA-1T ...................... AC CURRENT TRANSDUCERS Single Phase. ..... 4-5TA-3 & TA-3T ...................... AC CURRENT TRANSDUCERS Three Phase. ...... 4-5 TV-1 & TV-1T ...................... AC VOLTAGE TRANSDUCERS Single Phase. .......6-7 TV-3 & TV-3T ...................... AC VOLTAGE TRANSDUCERS Three Phase. ........6-7 TW-12 & TW-13................... Watts TRANSDUCERS Single Phase . .................. 8-9TW33 & TW-34 ................... Watts TRANSDUCERS Three Phase. .................... 8-9
TQ-12 & TQ-13 ................... VARs TRANSDUCERS Single Phase . ...............10-11TQ-33 & TQ-34 ................... VARs TRANSDUCERS Three Phase . ................10-11
TWQ-12 & TWQ-13 ............. Watts + VARs TRANSDUCERS Single Phase . .12-13TWQ-33 & TWQ-34 ............ Watts + VARs TRANSDUCERS Three Phase ...12-13
TWH-12 & TWH-13 ............. Watt Hours TRANSDUCERS Single Phase . .....14-15TWH-33 & TWH-34 ............ Watt Hours TRANSDUCERS Three Phase . ......14-15
TWWH-12 & TWWH-13 ...... Watt+Watt Hours TRANSDUCERS Single Phase . 16-17TWWH-33 & TWWH-34 ..... Watt + Watt Hours TRANSDUCERS Three Phase . 16-17
TQH-12 & TQH-13 ............. VAR Hours TRANSDUCERS Single Phase . ......18-19TQH-33 & TQH-34 ............. VAR Hours TRANSDUCERS Three Phase . .......18-19
TQQH-12 & TQQH-13 ........ VARs+VAR Hours TRANSDUCERS Single Phase . 20-21TQQH-33 & TQQH-34 ........ VARs+VAR Hours TRANSDUCERS Three Phase . 20-21
TPF-12 ................................. AC Power Factor TRANSDUCERS Single Phase . 22-23TPF-33 & TPF-34 ............... AC Power Factor TRANSDUCERS Three Phase . 22-23
TF-1 ..................................... FREQUENCY TRANSDUCERS . ......................... 24-25
TD-1 .................................... DC Volts or mA TRANSMITTER ISOLATOR . ... 26-27
CASE DIMENSIONS - CASE A & C. ......................................................................28
CASE DIMENSIONS - CASE B & D. ......................................................................29
Since 1976
(Z670)www.texmate.com 4
MODELS OFFERED
FEATURES
AC CURRENT TRANSDUCER
TA-1: 1 Phase, Average sensing AmpsTA-1T: 1 Phase, True rms sensing Amps
TA-3: 3 Phase, Average sensing AmpsTA-3T: 3 Phase, True rms sensing Amps
• High accuracy ±0.2% of Rated Output (R.O.)• Super high accuracy ±0.1% of Rated Output (R.O.) available as a special order.*• High immunity to external noise.• Quick and easy mounting to 35mm DIN Rail (DIN46277)• Many input and output signal combinations
GENERAL SPECIFICATIONSAccuracy ................................... ± 0.2% R.O. Standard for 10 to 100% of rated output
± 0.1% R.O. (Special Option)Temp. coefficient ..................... ≤100ppm/ºC of span
≤60ppm/ºC for ambient temperature of 25ºC ±10ºCTemp. range .............................. Storage temperature range -20ºC to 60ºC (-4ºF to 140ºF)
Operating temperature range 0ºC to 50ºC (32ºF to 122ºF)Humidity range ........................ Up to 95% RH non condensingIsolation .................................... Between Input/Output/Power/CaseDielectric test ........................... DIN-IEC 688
2K Vrms/1 min, Between terminal to terminal 2.8K Vrms/1 min, Between terminal to case
Surge test ................................. DIN-IEC 255-4, ANSI C37 90a/1974 5KV(1.2x50 µs)Insulation Resistance ............. Greater than 100 M Ω at 500V DCHousing material ..................... ABS Resin(94V-0) or metalMounting ................................... Screw mount on metal case or Plastic case DIN Rail 35mmAuxiliary Power ........................ AC 115/230V ± 15%, 50/60Hz, 3VA
DC 24V ± 20%(optional) 125V DC ± 20%(optional)
TA
• True RMS sensing is recommended for input signals with distortion. • Direct connect to the transducer for inputs ≤ 5A AC.
• Connect using a current Transformer (C.T.) for inputs greater than 5A AC.
Since 1976
(Z670)www.texmate.com 5
AC CURRENT TRANSDUCERS
1 2 3 4
5 6 7 8
OUTPUT INPUT
POWER
+
230 V115 V
LineNeutral
OUTPUT+
INPUT SPECIFICATIONSAC Input ................................... 0 to 5A AC, 0 to 1A AC or custom inputFrequency ................................. 45Hz to 65Hz or 400HzBurden ...................................... ≤0.2VAResponse Sensitivity .............. ≤0.5% of measuring range to maximum input rangeInput Overload Capacity ......... 3 times the rated input current continuously.
10 times the rated current for 10 seconds. 50 times the rated input current for 1 second. 80 times the rated input current for 0.5 second.
OUTPUT SPECIFICATIONSOutput Variables ..................... DC mA or DC VoltsRipple ........................................ < 0.5% of rated output. Peak to Peak (maximum)Response Time ........................ < 400 milliseconds to go from 0 to 99% of outputZero Adjustment ...................... ± 5% of rated output (minimum)Span Adjustment ..................... ± 10% of rated output (minimum)Load Resistance ...................... 10K Ω maximum for 0 to 1mA output
500 Ω maximum for 4 to 20mA output 500 Ω minimum for 0 to 10V output
CONNECTION DIAGRAM
TA-1/TA-1TA INPUT B INPUT C INPUT
+OUTPUT
BOUTPUT
A +OUTPUT
C+
+ + +
ACPOWER230 V
115 V
L2L1
L3
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
TA-3/TA-3T
TA
TA-1
1 Ph
ase,
Avg
sen
sing
Am
psR
O1
±0.2
%
SA1
0 to
5 A
AC
HZ1
45H
z to
65H
zO
A1
0 to
1 m
A D
C
P1P011
5/23
0V A
C ±1
5%
Sing
le P
ower
ed0-
1 m
A O
utpu
t Onl
yC
MM
etal
TA
-1T
1 Ph
ase,
TRM
S se
nsin
g A
mps
RO
3±0
.1%
SA2
0 to
1 A
AC
HZ4
400H
zO
A2
4 to
20m
A D
C
P224
V D
C ±1
5%
CP
Plas
ticTA
-33
Phas
e, A
vg s
ensi
ng A
mps
SAY
Cust
om In
put
OA
30
to 1
0 V
DC
P312
5V D
C ±1
5%TA
-3T
3 Ph
ase,
TRM
S se
nsin
g A
mps
OA
YCu
stom
Out
put
Cust
om P
ower
±15
%
Inpu
t Fre
quen
cyBa
se M
odel
Case
Inpu
t Sig
nal
Out
put S
igna
lA
uxili
ary
Pow
erA
ccur
acy
PY
Since 1976
(Z670)www.texmate.com 6
AC VOLTAGE TRANSDUCERS
MODELS OFFERED
FEATURES
TV-1: 1 Phase, Average sensingTV-1T: 1 Phase, True rms sensing
TV-3: 3 Phase, Average sensingTV-3T: 3 Phase, True rms sensing
• High accuracy ±0.2% of Rated Output (R.O.)• Super high accuracy ±0.1% of Rated Output (R.O.) available as a special order.*• High immunity to external noise.• Quick and easy mounting to 35mm DIN Rail (DIN46277)• Many input and output signal combinations
GENERAL SPECIFICATIONS
TV
• True RMS sensing is recommended for input signals with distortion. • Direct connect to the transducer for inputs ≤ 600V AC.• Connect using a Potential Transformer (P.T.) for inputs > 600V AC.
Accuracy ................................... ± 0.2% R.O. Standard for 10 to 100% of rated output ± 0.1% R.O. (Special Option)
Temp. coefficient ..................... ≤100ppm/ºC of span ≤60ppm/ºC for ambient temperature of 25ºC ±10ºC
Temp. range .............................. Storage temperature range -20ºC to 60ºC (-4ºF to 140ºF) Operating temperature range 0ºC to 50ºC (32ºF to 122ºF)
Humidity range ........................ Up to 95% RH non condensingIsolation .................................... Between Input/Output/Power/CaseDielectric test ........................... DIN-IEC 688
2K Vrms/1 min, Between terminal to terminal 2.8K Vrms/1 min, Between terminal to case
Surge test ................................. DIN-IEC 255-4, ANSI C37 90a/1974 5KV(1.2x50 µs)Insulation Resistance ............. Greater than 100 M Ω at 500V DCHousing material ..................... ABS Resin(94V-0) or metalMounting ................................... Screw mount on metal case or Plastic case DIN Rail 35mmAuxiliary Power ........................ AC 115/230V ± 15%, 50/60Hz, 3VA
DC 24V ± 20%(optional) 125V DC ± 20%(optional)
Since 1976
(Z670)www.texmate.com 7
AC VOLTAGE TRANSDUCERS
INPUT SPECIFICATIONSAC Input ............................... 0 to 150V AC, 0 to 300V AC, 0 to 600V AC or custom inputFrequency ........................... 45Hz to 65Hz or 400HzBurden ................................. ≤0.1VAResponse Sensitivity ......... ≤0.5% of measuring range to mazimum input rangeInput Overload Capacity .... 1.25 times the rated input voltage continuously.
2 times the rated voltage for 10 seconds. 4 times the rated input voltage for 5 seconds. Or 600V AC rms continuous.(absolute maximum)
OUTPUT SPECIFICATIONS
Output Variables ................. DC mA or DC VoltsRipple ................................... < 0.5% of rated output. Peak to Peak (maximum)Response Time ................... < 400 milliseconds to go from 0 to 99% of outputZero Adjustment ................. ± 5% of rated output minimumSpan Adjustment ................ ± 10% of rated output minimumLoad Resistance ................. 10K Ω maximum for 0 to 1mA output
500 Ω maximum for 4 to 20mA output 500 Ω minimum for 0 to 10V output
CONNECTION DIAGRAM
TV-1/TV-1T
1 2 3 4
5 6 7 8
OUTPUT INPUT
P.T.
POWER
+
230 V115 V
LineNeutralOUTPUT+
1S 1L 2S 2L 3S 3L
+OUTPUT
AOUTPUT
C+
+
+OUTPUT
B
+ +
ACPOWER230 V
115 V
L2L3
L1
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 181S 1L 2S 2L 3S 3L
+OUTPUT
BOUTPUT
A +OUTPUT
C+
+ + +
ACPOWER230 V
115 V
L3N
L2L1
P.T.1 P.T.2 P.T.3
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
Three Phase 3 wire Three Phase 4 wire TV-1
1 Ph
ase,
Avg
sen
sing
Vol
tsR
O1
±0.2
%SV
10
to 1
50V
AC
HZ1
45H
z to
65H
zO
V10
to 1
mA
DC
CM
Met
alTV
-1T
1 Ph
ase,
TRM
S se
nsin
g Vo
ltsR
O3
±0.1
%SV
20
to 3
00V
AC
HZ4
400H
zO
V24
to 2
0mA
DC
CP
Plas
ticTV
-33
Phas
e, A
vg s
ensi
ng V
olts
SV3
0 to
600
V A
CO
V30
to 1
0 V
DC
TV-3
T3
Phas
e, T
RMS
sens
ing
Volts
SVY
Cust
om In
put
OVY
Cust
om O
utpu
t
Inpu
t Fre
quen
cyBa
se M
odel
Inpu
t Sig
nal
Case
Aux
iliar
y Po
wer
Out
put S
igna
lA
ccur
acy
P1P011
5/23
0V A
C ±1
5%Si
ngle
Pow
ered
P224
V D
C ±1
5%
P312
5V D
C ±1
5%Cu
stom
Pow
er ±
15%
PY
TV
Since 1976
(Z670)www.texmate.com 8
MODELS OFFERED
FEATURES
Watts TRANSDUCERS
TW-12: Single Phase, 2 Wire – 1 ElementTW-13: Single Phase, 3 Wire – 2 ElementTW-33: 3 Phase, 3 Wire – 2 ElementTW-34: 3 Phase, 4 Wire – 3 Element
• Accurate measurement of the active power Watts for bal-anced or unbalanced loads.
• The output signals are isolated load independent DC mA or DC Volts, representing the measured value of the active power Watts.
• Uses Time Division Multiplication (TDM) for precision measurement of even distorted signals.• High accuracy ±0.2% of Rated Output (R.O.)• Super high accuracy ±0.1% of Rated Output (R.O.) available as a special order.*• High immunity to external noise.• Quick and easy mounting to 35mm DIN Rail (DIN46277) or screw mounting.• Many input and output signal combinations
GENERAL SPECIFICATIONS
Accuracy ................................... ± 0.2% R.O. Standard for 10 to 100% of rated output ± 0.1% R.O. (Special Option)
Temp. coefficient ..................... ≤100ppm/ºC of span ≤60ppm/ºC for ambient temperature of 25ºC ±10ºC
Temp. range .............................. Storage temperature range -20ºC to 60ºC (-4ºF to 140ºF) Operating temperature range 0ºC to 50ºC (32ºF to 122ºF)
Humidity range ........................ Up to 95% RH non condensingIsolation .................................... Between Input/Output/Power/CaseDielectric test ........................... DIN-IEC 688
2K Vrms/1 min, Between terminal to terminal 2.8K Vrms/1 min, Between terminal to case
Surge test ................................. DIN-IEC 255-4, ANSI C37 90a/1974 5KV(1.2x50 µs)Insulation Resistance ............. Greater than 100 M Ω at 500V DCHousing material ..................... ABS Resin(94V-0) or metalMounting ................................... Screw mount on metal case or Plastic case DIN Rail 35mmAuxiliary Power ........................ AC 115/230V ± 15%, 50/60Hz, 3VA
DC 24V ± 20%(optional) 125V DC ± 20%(optional)
TW
Since 1976
(Z670)www.texmate.com 9
INPUT SPECIFICATIONSAC Input .................................... 120V/5A AC, 240V/5A AC for 1ø/2 wire, 240V/120V, 5A AC for 1ø/ 3 Wire
120V/5A AC, 240V/5A AC for 3ø/3 Wire & 3ø / 4 Wire custom input (600V max /10A AC max)
Frequency ................................. 60Hz ±3Hz, 50Hz ±3Hz, 400Hz ±3Hz Burden ...................................... ≤0.2VA per current circuit, ≤0.1VA per voltage circuit.Response Sensitivity .............. ≤0.5% of measuring range to maximum input rangeInput Voltage ............................ 600V AC rms continuous (absolute maximum)
Overload Capacity 1.25 times the rated input Voltage continuously. 2 times the rated input Voltage for 10 secs. 4 times the rated input Voltage for 5 secs.
Input Current ............................ 3 times the rated input current continuously. Overload Capacity 10 times the rated input current for 10 secs. 50 times the rated input current for 1 sec. 80 times the rated input current for 0.5 secs
OUTPUT SPECIFICATIONSOutput Variables ...................... DC mA or DC VoltsRipple ........................................ < 0.5% of rated output. Peak to Peak (maximum)Response Time ........................ < 400 milliseconds to go from 0 to 99% of outputZero Adjustment ...................... ± 5% of rated output (minimum)Span Adjustment ..................... ± 10% of rated output (minimum)Load Resistance ...................... 10 kΩ maximum for 0 to 1mA output
500 Ω maximum for 4 to 20mA output 500 Ω minimum for 0 to 10V output
Maximum Input range value = (CT Ratio) X (PT Ratio) X (Nominal Watts)If CT = 200A:5A PT is 3300V:110V Nominal Watts = 500 then CT Ratio = 40 then PT Ratio = 30 and Maximum input range value = 40 x 30 x 500 = 600KW
Watts TRANSDUCERS
+OUTPUT
OUTPUT+
ACPOWER230 V
115 V
LC.T.1
P.T.1
N
1S 1L
P1 P21 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
+OUTPUT
OUTPUT+
ACPOWER230 V
115 V
L1 C.T.1
P0 P2P1
1S 1L 3S 3L
C.T.3
P.T.1 P.T.2
L2N
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
+OUTPUT
OUTPUT+
ACPOWER230 V
115 V
L1 C.T.1
P2 P3P1
1S 1L 3S 3L
C.T.3
P.T.1 P.T.3
L2L3
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
+OUTPUT
OUTPUT+
ACPOWER230 V
115 V
L1C.T.1
P2 P3P1P0
1S 1L 2S 2L 3S 3L
C.T.3C.T.2
P.T.
2
P.T.
1
P.T.
3
L2L3N
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
CONNECTION DIAGRAM
TW-1
21
Phas
e, 1
P/2W
, 1E,
Wat
tsR
O1
±0.2
%SW
112
0V/5
A A
CH
Z660
Hz
OW
10
to 1
mA
DC
CM
Met
alTW
-13
1 Ph
ase,
1P/
3W, 2
E, W
atts
RO
3±0
.1%
SW2
240V
/5A
AC
HZ5
50H
zO
W2
4 to
20m
A D
CC
PPl
astic
TW-3
33
Phas
e, 3
P/3W
, 2E,
Wat
tsSW
YCu
stom
Inpu
t, M
AX
10A
HZ4
400H
zO
W3
0 to
10
V D
CTW
-34
3 Ph
ase,
3P/
4W, 3
E, W
atts
OW
YCu
stom
Out
put
Base
Mod
el
Case
Aux
iliar
y Po
wer
Inpu
t Sig
nal
Out
put S
igna
lA
ccur
acy
Inpu
t Fre
quen
cy
P1P011
5/23
0V A
C ±1
5%Si
ngle
Pow
ered
P224
V D
C ±1
5%
P312
5V D
C ±1
5%Cu
stom
Pow
er ±
15%
PY
TW
TW-12 TW-13
TW-33 TW-34
Since 1976
(Z670)www.texmate.com 10
MODELS OFFERED
FEATURES• Uses Time Division Multiplication (TDM) for precision measurement of even distorted signals.• High accuracy ±0.2% of Rated Output (R.O.)• Super high accuracy ±0.1% of Rated Output (R.O.) available as a special order.*• High immunity to external noise.• Quick and easy mounting to 35mm DIN Rail (DIN46277) or screw mounting.• Many input and output signal combinations
VARs TRANSDUCERS
TQ-12: Single Phase, 2 Wire – 1 Element
TQ-13: Single Phase, 3 Wire – 2 Element
TQ-33: 3 Phase, 3 Wire – 2 Element
TQ-34: 3 Phase, 4 Wire – 3 Element
• Accurate measurement of the active power Watts for balanced or unbalanced loads.
• The output signals are isolated load independent DC mA or DC Volts, representing the measured value of the active power Watts.
GENERAL SPECIFICATIONSAccuracy ................................... ± 0.2% R.O. Standard for 10 to 100% of rated output
± 0.1% R.O. (Special Option)Temp. coefficient ..................... ≤100ppm/ºC of span
≤60ppm/ºC for ambient temperature of 25ºC ±10ºCTemp. range .............................. Storage temperature range -20ºC to 60ºC (-4ºF to 140ºF)
Operating temperature range 0ºC to 50ºC (32ºF to 122ºF)Humidity range ........................ Up to 95% RH non condensingIsolation .................................... Between Input/Output/Power/CaseDielectric test ........................... DIN-IEC 688
2K Vrms/1 min, Between terminal to terminal 2.8K Vrms/1 min, Between terminal to case
Surge test ................................. DIN-IEC 255-4, ANSI C37 90a/1974 5KV(1.2x50 µs)Insulation Resistance ............. Greater than 100 M Ω at 500V DCHousing material ..................... ABS Resin(94V-0) or metalMounting ................................... Screw mount on metal case or Plastic case DIN Rail 35mmAuxiliary Power ........................ AC 115/230V ± 15%, 50/60Hz, 3VA
DC 24V ± 20%(optional) 125V DC ± 20%(optional)
TQ
Since 1976
(Z670)www.texmate.com 11
OUTPUT SPECIFICATIONSOutput Variables ...................... DC mA or DC VoltsRipple ........................................ < 0.5% of rated output. Peak to Peak (maximum)Response Time ........................ < 400 milliseconds to go from 0 to 99% of outputZero Adjustment ...................... ± 5% of rated output (minimum)Span Adjustment ..................... ± 10% of rated output (minimum)Load Resistance ...................... 10 kΩ maximum for 0 to 1mA output
500 Ω maximum for 4 to 20mA output 500 Ω minimum for 0 to 10V output
Maximum Input range value = (CT Ratio) X (PT Ratio) X (Nominal VARs)If CT = 200A:5A PT is 3300V:110V Nominal VARs = 500 CT Ratio = 40 PT Ratio = 30 and Maximum input range value = 40 x 30 x 500 = 600KVAR
VARs TRANSDUCERS
INPUT SPECIFICATIONSAC Input .................................... 120V/5A AC, 240V/5A AC for 1ø/2 wire, 240V/120V, 5A AC for 1ø/ 3 Wire
120V/5A AC, 240V/5A AC for 3ø/3 Wire & 3ø / 4 Wire custom input (600V max /10A AC max)
Frequency ................................. 60Hz ±3Hz, 50Hz ±3Hz, 400Hz ±3Hz Burden ...................................... ≤0.2VA per current circuit, ≤0.1VA per voltage circuit.Response Sensitivity .............. ≤0.5% of measuring range to maximum input rangeInput Voltage ............................ 600V AC rms continuous (absolute maximum)
Overload Capacity 1.25 times the rated input Voltage continuously. 2 times the rated input Voltage for 10 secs. 4 times the rated input Voltage for 5 secs.
Input Current ............................ 3 times the rated input current continuously. Overload Capacity 10 times the rated input current for 10 secs. 50 times the rated input current for 1 sec. 80 times the rated input current for 0.5 secs
+OUTPUT
OUTPUT+
ACPOWER230 V
115 V
LC.T.1
P.T.1
N
1S 1L
P1 P21 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
+OUTPUT
OUTPUT+
ACPOWER230 V
115 V
L1 C.T.1
P0 P2P1
1S 1L 3S 3L
C.T.3
P.T.1 P.T.2
L2N
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
+OUTPUT
OUTPUT+
ACPOWER230 V
115 V
L1 C.T.1
P2 P3P1
1S 1L 3S 3L
C.T.3
P.T.1 P.T.3
L2L3
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
+OUTPUT
OUTPUT+
ACPOWER230 V
115 V
L1C.T.1
P2 P3P1P0
1S 1L 2S 2L 3S 3L
C.T.3C.T.2
P.T.
2
P.T.
1
P.T.
3
L2L3N
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
CONNECTION DIAGRAM
TQ
TQ-1
21
Phas
e, 1
P/2W
, 1E,
VA
RsR
O1
±0.2
%SW
112
0V/5
A A
CH
Z660
Hz
OQ
4±1
mA
DC
LGLA
G =
+ P
olar
ityC
MM
etal
TQ-1
31
Phas
e, 1
P/3W
, 2E,
VA
RsR
O3
±0.1
%SW
224
0V/5
A A
CH
Z550
Hz
OQ
512
± 8
mA
DC
LDLE
AD
= +
Pola
rity
CP
Plas
ticTQ
-33
3 Ph
ase,
3P/
3W, 2
E, V
ARs
SWY
Cust
om In
put
HZ4
400H
zO
Q6
±10
V D
CTQ
-34
3 Ph
ase,
3P/
4W, 3
E, V
ARs
OQ
YCu
stom
Out
put
Case
Acc
urac
yIn
put F
requ
ency
Base
Mod
el
Aux
iliar
y Po
wer
Inpu
t Sig
nal
Out
put S
igna
lIn
put/
Out
put
Rela
tions
hip
P1P011
5/23
0V A
C ±1
5%Si
ngle
Pow
ered
P224
V D
C ±1
5%
P312
5V D
C ±1
5%Cu
stom
Pow
er ±
15%
PY
TQ-12
TQ-33 TQ-34
TQ-13
Since 1976
(Z670)www.texmate.com 12
MODELS OFFERED
Watts + VARs TRANSDUCERS
TWQ-12: 1 Phase, 2 Wire – 1 ElementTWQ-13: 1 Phase, 3 Wire – 2 ElementTWQ-33: 3 Phase, 3 Wire – 2 ElementTWQ-34: 3 Phase, 4 Wire – 3 Element
• Uses Time Division Multiplication (TDM) for precision measurement of even distorted signals.• High accuracy ±0.2% of Rated Output (R.O.)• Super high accuracy ±0.1% of Rated Output (R.O.) available as a special order.*• High immunity to external noise.• Quick and easy mounting to 35mm DIN Rail (DIN46277) or screw mounting.• Many input and output signal combinations
GENERAL SPECIFICATIONSAccuracy ................................... ± 0.2% R.O. Standard for 10 to 100% of rated output
± 0.1% R.O. (Special Option)Temp. coefficient ..................... ≤100ppm/ºC of span
≤60ppm/ºC for ambient temperature of 25ºC ±10ºCTemp. range .............................. Storage temperature range -20ºC to 60ºC (-4ºF to 140ºF)
Operating temperature range 0ºC to 50ºC (32ºF to 122ºF)Humidity range ........................ Up to 95% RH non condensingIsolation .................................... Between Input/Output/Power/CaseDielectric test ........................... DIN-IEC 688
2K Vrms/1 min, Between terminal to terminal 2.8K Vrms/1 min, Between terminal to case
Surge test ................................. DIN-IEC 255-4, ANSI C37 90a/1974 5KV(1.2x50 µs)Insulation Resistance ............. Greater than 100 M Ω at 500V DCHousing material ..................... ABS Resin(94V-0) or metalMounting ................................... Screw mount on metal case or Plastic case DIN Rail 35mmAuxiliary Power ........................ AC 115/230V ± 15%, 50/60Hz, 3VA
DC 24V ± 20%(optional), 125V DC ± 20%(optional)
FEATURES
TWQ
• Accurate measurement of the active power and reactive power (Watts and VARs) of a single/ three phase system with balanced or unbalanced loads.
• The output signals are isolated load independent DC mA or DC Volts, representing the measured value of the active and reactive power (Watts and VARs).
INPUT SPECIFICATIONSAC Input .................................... 120V/5A AC, 240V/5A AC for 1ø/2 wire, 240V/120V, 5A AC for 1ø/ 3 Wire
120V/5A AC, 240V/5A AC for 3ø/3 Wire & 3ø / 4 Wire custom input (600V max /10A AC max)
Frequency ................................. 60Hz ±3Hz, 50Hz ±3Hz, 400Hz ±3Hz Burden ...................................... ≤0.2VA per current circuit, ≤0.1VA per voltage circuit.Response Sensitivity .............. ≤0.5% of measuring range to maximum input rangeInput Voltage ............................ 600V AC rms continuous (absolute maximum)
Overload Capacity 1.25 times the rated input Voltage continuously. 2 times the rated input Voltage for 10 secs. 4 times the rated input Voltage for 5 secs.
Input Current ............................ 3 times the rated input current continuously. 10 times the rated input current for 10 secs. Overload Capacity 50 times the rated input current for 1 sec. 80 times the rated input current for 0.5 secs
Since 1976
(Z670)www.texmate.com 13
OUTPUT SPECIFICATIONSOutput Variables ...................... DC mA or DC VoltsRipple ........................................ < 0.5% of rated output. Peak to Peak (maximum)Response Time ........................ < 400 milliseconds to go from 0 to 99% of outputZero Adjustment ...................... ± 5% of rated output (minimum)Span Adjustment ..................... ± 10% of rated output (minimum)Load Resistance ...................... 10 kΩ maximum for 0 to 1mA output
500 Ω maximum for 4 to 20mA output 500 Ω minimum for 0 to 10V output
To calculate the actual Watts and VARs Maximum Input range value, the CT and PT ratios have to be factored inMaximum input Range for Watts = (CT Ratio) X (PT Ratio) X (Nominal Watts)Maximum Input range value for VARs = (CT Ratio) X (PT Ratio) X (Nominal VARs)
For example:If CT = 200A:5A PT is 3300V:110V Nominal Watts = 1000 Nominal VARs = 1000 then CT Ratio = 40 then PT Ratio = 30 and Maximum input range value for Watts = 40 x 30 x 1000 = 1200KWattsMaximum input range value for VARs = 40 x 30 x 1000 = 1200KVARs
Watts + VARs TRANSDUCERS
CONNECTION DIAGRAM
+WATT
OUTPUT
OUTPUT+
ACPOWER230 V
115 V
LC.T.1
P.T.1
N
1S 1L
P1 P2
+VAR
OUTPUT
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
+WATT
OUTPUT +VAE
OUTPUT
OUTPUT+
ACPOWER230 V
115 V
L1 C.T.1
P0 P2P1
1S 1L 3S 3L
C.T.3
P.T.1 P.T.2
L2
N
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
TWQ-12 TWQ-13
OUTPUT+
ACPOWER230 V
115 V
L1 C.T.1
P2 P3P1
1S 1L 3S 3L
C.T.3
P.T.1 P.T.3
L2
L3
+WATT
OUTPUT +VAR
OUTPUT
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
OUTPUT+
ACPOWER230 V
115 V
L1C.T.1
P2 P3P1P0
1S 1L 2S 2L 3S 3L
C.T.3C.T.2
P.T.
2
P.T.
1
P.T.
3
L2
L3
N
+WATT
OUTPUT +VAR
OUTPUT
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
TWQ-33 TWQ-34
TWQ
TWQ
-12
1 Ph
ase,
1P/
2W, 1
E, W
att +
VA
RsR
O1
±0.2
%SW
112
0V/5
A A
CH
Z660
Hz
OW
V1W
atts
0 to
1 m
A D
CVA
Rs ±
1mA
DC
LGLA
G =
+ P
olar
ityC
MM
etal
TWQ
-13
1 Ph
ase,
1P/
3W, 2
E, W
att +
VA
RsR
O3
±0.1
%SW
224
0V/5
A A
CH
Z550
Hz
OW
V2W
atts
4 to
20m
A D
CVA
Rs 1
2 ±
8mA
DC
LDLE
AD
= +
Pola
rity
CP
Plas
tic
TWQ
-33
3 Ph
ase,
3P/
3W, 2
E, W
att +
VA
RsSW
YCu
stom
Inpu
tH
Z440
0Hz
OW
V5W
atts
12
± 8m
A D
CVA
Rs 1
2 ±
8mA
DC
TWQ
-34
3 Ph
ase,
3P/
4W, 3
E, W
att +
VA
RsO
WV6
Wat
ts 0
to 1
0V D
CVA
Rs ±
10V
DC
Base
Mod
el
Acc
urac
yA
uxili
ary
Pow
erIn
put S
igna
lO
utpu
t Sig
nal
Inpu
t/O
utpu
tRe
latio
nshi
pCa
seIn
put F
requ
ency
P1P0
115/
230V
AC
±15%
Sing
le P
ower
ed0
+/- 1
mA
Out
put O
nly
P224
V D
C ±1
5%
P312
5V D
C ±1
5%Cu
stom
Pow
er ±
15%
PY
Since 1976
(Z670)www.texmate.com 14
MODELS OFFEREDTWH-12: 1 Phase, 2 Wire – 1 ElementTWH-13: 1 Phase, 3 Wire – 2 ElementTWH-33: 3 Phase, 3 Wire – 2 ElementTWH-34: 3 Phase, 4 Wire – 3 Element
• Uses Time Division Multiplication (TDM) for precision measurement of even distorted signals.• High accuracy ±0.2% of Rated Output (R.O.)• Super high accuracy ±0.1% of Rated Output (R.O.) available as a special order.*• High immunity to external noise.• Quick and easy mounting to 35mm DIN Rail (DIN46277) or screw mounting.• Many input and output signal combinations.
Watt Hours TRANSDUCERSTWH
• Accurate measurement of the active energy (Watt Hours) of a single phase system with balanced or unbalanced loads.
• The output signals are isolated load independent pulses, representing the measured value of the active energy (WattHours, forward and reverse).
GENERAL SPECIFICATIONSAccuracy ................................... ± 0.2% R.O. Standard for 10 to 100% of rated output
± 0.1% R.O. (Special Option)Temp. coefficient ..................... ≤100ppm/ºC of span
≤60ppm/ºC for ambient temperature of 25ºC ±10ºCTemp. range .............................. Storage temperature range -20ºC to 60ºC (-4ºF to 140ºF)
Operating temperature range 0ºC to 50ºC (32ºF to 122ºF)Humidity range ........................ Up to 95% RH non condensingIsolation .................................... Between Input/Output/Power/CaseDielectric test ........................... DIN-IEC 688
2K Vrms/1 min, Between terminal to terminal 2.8K Vrms/1 min, Between terminal to case
Surge test ................................. DIN-IEC 255-4, ANSI C37 90a/1974 5KV(1.2x50 µs)Insulation Resistance ............. Greater than 100 M Ω at 500V DCHousing material ..................... ABS Resin(94V-0) or metalMounting ................................... Screw mount on metal case or Plastic case DIN Rail 35mmAuxiliary Power ........................ AC 115/230V ± 15%, 50/60Hz, 3VA
DC 24V ± 20%(optional), 125V DC ± 20%(optional)
FEATURES
INPUT SPECIFICATIONSAC Input .................................... 120V/5A AC, 240V/5A AC for 1ø/2 wire, 240V/120V, 5A AC for 1ø/ 3 Wire
120V/5A AC, 240V/5A AC for 3ø/3 Wire & 3ø / 4 Wire custom input (600V max /10A AC max)
Frequency ................................. 60Hz ±3Hz, 50Hz ±3Hz, 400Hz ±3Hz Burden ...................................... ≤0.2VA per current circuit, ≤0.1VA per voltage circuit.Response Sensitivity .............. ≤0.5% of measuring range to maximum input rangeInput Voltage ............................ 600V AC rms continuous (absolute maximum)
Overload Capacity 1.25 times the rated input Voltage continuously. 2 times the rated input Voltage for 10 secs. 4 times the rated input Voltage for 5 secs.
Input Current ............................ 3 times the rated input current continuously. 10 times the rated input current for 10 secs. Overload Capacity 50 times the rated input current for 1 sec. 80 times the rated input current for 0.5 secs
Since 1976
(Z670)www.texmate.com 15
Watt Hours TRANSDUCERS
Output Variables ................. PulsesRipple ................................... < 0.5% of rated output. Peak to Peak (maximum)Response Time ................... < 400 milliseconds to go from 0 to 99% of outputZero Adjustment ................. ± 5% of rated output (minimum)Span Adjustment ................ ± 10% of rated output (minimum)
To calculate the actual WattHours for each output pulse, the CT and PT ratios have to be factored in
WattHours per Output Pulse = (CT Ratio) X (PT Ratio) Nominal Pulses /WattHour
Calculation example: For Single phase 2 wire, TWH-12If CT = 200A:5A then CT Ratio = 40 PT is 3300V:110V then PT Ratio = 30
If 1 pulse per WattHour is selected, the output will actually be 1 pulse per 1200 WattHoursIf 10 pulse per WattHour is selected, the output will actually be 1 pulse per 120 WattHoursIf 100 pulse per WattHour is selected, the output will actually be 1 pulse per 12 WattHours
OUTPUT SPECIFICATIONS
CONNECTION DIAGRAM
TWH
OUTPUT+ +
ACPOWER230 V
115 V
L C.T.1
P2P1
1S 1L 3S 3L
P.T.1
N
+ +FORW
ARD
PULS
E O
UTPU
T
REVE
RSE
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
TWH-12
TWH-33
TWH-13
TWH-34
OUTPUT+ +
ACPOWER230 V
115 V
L1 C.T.1
P2 P3P1
1S 1L 3S 3L
C.T.3
P.T.1 P.T.3
N
L2
+ +FORW
ARD
PULS
E O
UTPU
T
REVE
RSE
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
ACPOWER230 V
115 V
L1 C.T.1
P2 P3P1
1S 1L 3S 3L
C.T.3
P.T.1 P.T.3
L2
L3
OUTPUT+ +
+ +FORW
ARD
PULS
E O
UTPU
T
REVE
RSE
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
ACPOWER230 V
115 V
L1C.T.1
P2 P3P1P0
1S 1L 2S 2L 3S 3L
C.T.3C.T.2
P.T.
2
P.T.
1
P.T.
3
L2
L3
N
OUTPUT+ +
+ +FORW
ARD
PULS
E O
UTPU
T
REVE
RSE
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
TWH
-12
1 Ph
ase,
1P/
2W, 1
E, W
atth
ours
RO1
±0.2
%SW
112
0V/5
A A
CH
Z660
Hz
OR1
Reed
Rel
ay.
P111
5/23
0 VA
C ±1
5%PU
11
puls
e pe
r WH
CM
Met
al
TWH
-13
1 Ph
ase,
1P/
3W, 2
E, W
atth
ours
RO3
±0.1
%SW
224
0V/5
A A
CH
Z550
Hz
OR2
Reed
Rel
ay.
Forw
ard
+ Re
vers
eP2
24 V
DC
±15%
PU2
10 P
ulse
s Pe
r WH
CP
Plas
tic
TWH
-33
3 Ph
ase,
3P/
3W, 2
E, W
atth
ours
SWY
Cust
om In
put
HZ4
400H
zO
C1
Ope
n Co
llect
or.
Forw
ard
only
P312
5 VD
C ±1
5%PU
310
0 pu
lses
per
WH
TWH
-34
3 Ph
ase,
3P/
4W, 3
E, W
atth
ours
OC
2O
pen
Colle
ctor
. Fo
rwar
d +
Reve
rse
PYCu
stom
Pow
er ±
15%
PU4
1 pu
lse
per 1
000W
H
Aux
iliar
y Po
wer
Puls
e pe
r Wat
tHou
rIn
put F
requ
ency
Case
Inpu
t Sig
nal
Out
put S
igna
lBa
se M
odel
A
ccur
acy
Forw
ard
only
Since 1976
(Z670)www.texmate.com 16
MODELS OFFERED
FEATURES
TWWH-12 base model 1 Phase, 2 Wire – 1 Element TWWH-13 base model 1 Phase, 3 Wire – 2 Element TWWH-33 base model 3 Phase, 3 Wire – 2 Element TWWH-34 base model 3 Phase, 4 Wire – 3 Element
• Uses Time Division Multiplication (TDM) for precision measurement of even distorted signals.• High accuracy ±0.2% of Rated Output (R.O.)• Super high accuracy ±0.1% of Rated Output (R.O.) available as a special order.*• High immunity to external noise.• Quick and easy mounting to 35mm DIN Rail (DIN46277) or screw mounting.• Many input and output signal combinations.
GENERAL SPECIFICATIONS
Watt+Watt Hours TRANSDUCERS TWWH
• Accurate measurement of the active energy (WattHours) of a three phase system with balanced or unbalanced loads.
• The output signals are isolated load independent pulses, represent-ing the measured value of the active energy (WattHours, forward and reverse) and DC mA or DC V for the active power (Watts).
Accuracy ................................... ± 0.2% R.O. Standard for 10 to 100% of rated output ± 0.1% R.O. (Special Option)
Temp. coefficient ..................... ≤100ppm/ºC of span ≤60ppm/ºC for ambient temperature of 25ºC ±10ºC
Temp. range .............................. Storage temperature range -20ºC to 60ºC (-4ºF to 140ºF) Operating temperature range 0ºC to 50ºC (32ºF to 122ºF)
Humidity range ........................ Up to 95% RH non condensingIsolation .................................... Between Input/Output/Power/CaseDielectric test ........................... DIN-IEC 688
2K Vrms/1 min, Between terminal to terminal 2.8K Vrms/1 min, Between terminal to case
Surge test ................................. DIN-IEC 255-4, ANSI C37 90a/1974 5KV(1.2x50 µs)Insulation Resistance ............. Greater than 100 M Ω at 500V DCHousing material ..................... ABS Resin(94V-0) or metalMounting ................................... Screw mount on metal case or Plastic case on DIN Rail 35mmAuxiliary Power ........................ AC 115/230V ± 15%, 50/60Hz, 3VA
DC 24V ± 20%(optional) 125V DC ± 20%(optional)
INPUT SPECIFICATIONSAC Input .................................... 120V/5A AC, 240V/5A AC. Custom input (600V max /10A AC max)Frequency ................................. 60Hz ±3Hz, 50Hz ±3Hz, 400Hz ±3Hz Burden ...................................... ≤0.2VA per current circuit, ≤0.1VA per voltage circuit.Response Sensitivity .............. ≤0.5% of measuring range to maximum input rangeInput Voltage ............................ 600V AC rms continuous (absolute maximum)
Overload Capacity 1.25 times the rated input Voltage continuously. 2 times the rated input Voltage for 10 secs. 4 times the rated input Voltage for 5 secs.
Input Current ............................ 3 times the rated input current continuously. Overload Capacity 10 times the rated input current for 10 secs. 50 times the rated input current for 1 sec. 80 times the rated input current for 0.5 secs
Since 1976
(Z670)www.texmate.com 17
Watt+Watt Hours TRANSDUCERS
OUTPUT SPECIFICATIONSOutput Variables ................. Pulses (WattHours) and DC mA or DC V (Watts)Ripple ................................... < 0.5% of rated output. Peak to Peak (maximum)Response Time ................... < 400 milliseconds to go from 0 to 99% of outputZero Adjustment ................. ± 5% of rated output (minimum)Span Adjustment ................ ± 10% of rated output (minimum)
To calculate the actual WattHours and Watts for each output pulse, the CT and PT ratios have to be factored in Watts = (CT Ratio) X (PT Ratio) x Nominal Watts
WattHours per Output Pulse = (CT Ratio) X (PT Ratio) Nominal Pulses /WattHour Calculation example: For Single phase 2 wire, TWWH-12If CT = 200A:5A then CT Ratio = 40 PT is 3300V:110V then PT Ratio = 30 Watts = 30 x 40 x 500 = 600kW
If 1 pulse per WattHour is selected, the output will actually be 1 pulse per 1200 WattHoursIf 10 pulse per WattHour is selected, the output will actually be 1 pulse per 120 WattHoursIf 100 pulse per WattHour is selected, the output will actually be 1 pulse per 12 WattHours
+ +
ACPOWER230 V
115 V
L C.T.1
P2P1
1S 1L 3S 3L
P.T.1
N
+ +FORW
ARD
PULS
E O
UTPU
T
REVE
RSE
PULSEOUTPUT
+DC
OUTPUT
DCOUTPUT+
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
CONNECTION DIAGRAM
PULSEOUTPUT
+ +
ACPOWER230 V
115 V
L1 C.T.1
P2 P3P1
1S 1L 3S 3L
C.T.3
P.T.1 P.T.3
N
L2
+ +FORW
ARD
PULS
E O
UTPU
T
REVE
RSE
+DC
OUTPUT
DCOUTPUT+
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
ACPOWER230 V
115 V
L1 C.T.1
P2 P3P1
1S 1L 3S 3L
C.T.3
P.T.1 P.T.3
L2
L3
PULSEOUTPUT
+ +
+ +FORW
ARD
PULS
E O
UTPU
T
REVE
RSE
+DC
OUTPUT
DCOUTPUT
+
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
ACPOWER230 V
115 V
L1C.T.1
P2 P3P1P0
1S 1L 2S 2L 3S 3L
C.T.3C.T.2
P.T.
2
P.T.
1
P.T.
3
L2
L3
N
PULSEOUTPUT
+ +
+ +FORW
ARD
PULS
E O
UTPU
T
REVE
RSE
+DC
OUTPUT
DCOUTPUT
+
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
TWWH
TWWH-12 TWWH-13
TWWH-33 TWWH-34 TWW
H-1
21
Phas
e, 1
P/2W
, 1E,
W
atts
+Wat
thou
rsR
O1
±0.
2%SW
112
0V/5
A A
CH
Z660
Hz
OW
R1
Wat
ts 0
to 1
mA
DC
WH
r Ree
d Re
lay.
For
war
d on
ly
P111
5/23
0 VA
C ±1
5%PU
11
puls
e/W
HC
MM
etal
TWW
H-1
31
Phas
e, 1
P/3W
, 2E,
W
atts
+Wat
thou
rsR
O3
±0.1
%SW
224
0V/5
A A
CH
Z550
Hz
OW
R2
Wat
ts 4
to 2
0 m
A D
CW
Hr R
eed
Rela
y. F
orw
ard
and
Reve
rse
P224
VD
C ±1
5%PU
210
Pul
ses/
WH
CP
Plas
tic
TWW
H-3
33
Phas
e, 3
P/3W
, 2E,
W
atts
+Wat
thou
rsSW
YCu
stom
Inpu
tH
Z440
0Hz
OW
C1
Wat
ts 0
to 1
mA
DC
WH
r Ope
n Co
llect
or. F
orw
ard
only
P312
5 VD
C ±1
5%PU
310
0 pu
lses
/WH
TWW
H-3
43
Phas
e, 3
P/4W
, 3E,
W
atts
+Wat
thou
rsO
WC
2W
atts
4 to
20
mA
DC
WH
r Ope
n Co
llect
or. F
orw
ard
+ Re
vers
ePY
Cust
om P
ower
±1
5%PU
41
puls
e/10
00W
H
Acc
urac
yBa
se M
odel
Inpu
t Sig
nal
Out
put S
igna
lA
uxili
ary
Pow
erCa
sePu
lse
per W
attH
our
Freq
uenc
y
Since 1976
(Z670)www.texmate.com 18
MODELS OFFEREDTQH-12: 1 Phase, 2 Wire – 1 ElementTQH-13: 1 Phase, 3 Wire – 2 ElementTQH-33: 3 Phase, 3 Wire – 2 ElementTQH-34: 3 Phase, 4 Wire – 3 Element
• Uses Time Division Multiplication (TDM) for precision measurement of even distorted signals.• High accuracy ±0.2% of Rated Output (R.O.)• Super high accuracy ±0.1% of Rated Output (R.O.) available as a special order.*• High immunity to external noise.• Quick and easy mounting to 35mm DIN Rail (DIN46277) or screw mounting.• Many input and output signal combinations.
VAR Hours TRANSDUCERS TQH
• Accurate measurement of the reactive energy (VAR Hours) of a single phase system with balanced or unbalanced loads.
• The output signals are isolated load independent DC mA or DC Volts, representing the measured value of the active energy (WattHours, forward and reverse).
FEATURES
GENERAL SPECIFICATIONSAccuracy ................................... ± 0.2% R.O. Standard for 10 to 100% of rated output
± 0.1% R.O. (Special Option)Temp. coefficient ..................... ≤100ppm/ºC of span
≤60ppm/ºC for ambient temperature of 25ºC ±10ºCTemp. range .............................. Storage temperature range -20ºC to 60ºC (-4ºF to 140ºF)
Operating temperature range 0ºC to 50ºC (32ºF to 122ºF)Humidity range ........................ Up to 95% RH non condensingIsolation .................................... Between Input/Output/Power/CaseDielectric test ........................... DIN-IEC 688
2K Vrms/1 min, Between terminal to terminal 2.8K Vrms/1 min, Between terminal to case
Surge test ................................. DIN-IEC 255-4, ANSI C37 90a/1974 5KV(1.2x50 µs)Insulation Resistance ............. Greater than 100 M Ω at 500V DCHousing material ..................... ABS Resin(94V-0) or metalMounting ................................... Screw mount on metal case or Plastic case on DIN Rail 35mmAuxiliary Power ........................ AC 115/230V ± 15%, 50/60Hz, 3VA
DC 24V ± 20%(optional) 125V DC ± 20%(optional)
INPUT SPECIFICATIONSAC Input .................................... 120V/5A AC, 240V/5A AC. Custom input (600V max /10A AC max)Frequency ................................. 60Hz ±3Hz, 50Hz ±3Hz, 400Hz ±3Hz Burden ...................................... ≤0.2VA per current circuit, ≤0.1VA per voltage circuit.Response Sensitivity .............. ≤0.5% of measuring range to maximum input rangeInput Voltage ............................ 600V AC rms continuous (absolute maximum)
Overload Capacity 1.25 times the rated input Voltage continuously. 2 times the rated input Voltage for 10 secs. 4 times the rated input Voltage for 5 secs.
Input Current ............................ 3 times the rated input current continuously. Overload Capacity 10 times the rated input current for 10 secs. 50 times the rated input current for 1 sec. 80 times the rated input current for 0.5 secs
Since 1976
(Z670)www.texmate.com 19
VAR Hours TRANSDUCERS
OUTPUT SPECIFICATIONSOutput Variables ................. PulsesRipple ................................... < 0.5% of rated output. Peak to Peak (maximum)Response Time ................... < 400 milliseconds to go from 0 to 99% of outputZero Adjustment ................. ± 5% of rated output (minimum)Span Adjustment ................ ± 10% of rated output (minimum)
To calculate the actual VARHours for each output pulse, the CT and PT ratios have to be factored in
VARHours per Output Pulse = (CT Ratio) X (PT Ratio) Nominal Pulses /VARHour
Calculation example: For Single phase 2 wire, TQH-12If CT = 200A:5A then CT Ratio = 40 PT is 3300V:110V then PT Ratio = 30
If 1 pulse per VARHour is selected, the output will actually be 1 pulse per 1200 WARHoursIf 10 pulse per VARHour is selected, the output will actually be 1 pulse per 120 VARHoursIf 100 pulse per VARHour is selected, the output will actually be 1 pulse per 12 VARHours
CONNECTION DIAGRAM
OUTPUT+ +
ACPOWER230 V
115 V
L C.T.1
P2P1
1S 1L 3S 3L
P.T.1
N
+ +FORW
ARD
PULS
E O
UTPU
T
REVE
RSE
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
OUTPUT+ +
ACPOWER230 V
115 V
L1 C.T.1
P2 P3P1
1S 1L 3S 3L
C.T.3
P.T.1 P.T.3
N
L2
+ +FORW
ARD
PULS
E O
UTPU
T
REVE
RSE
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
TQH-12 TQH-13
ACPOWER230 V
115 V
L1 C.T.1
P2 P3P1
1S 1L 3S 3L
C.T.3
P.T.1 P.T.3
L2
L3
OUTPUT+ +
+ +FORW
ARD
PULS
E O
UTPU
T
REVE
RSE
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
ACPOWER230 V
115 V
L1C.T.1
P2 P3P1P0
1S 1L 2S 2L 3S 3L
C.T.3C.T.2
P.T.
2
P.T.
1
P.T.
3
L2
L3
N
OUTPUT+ +
+ +FORW
ARD
PULS
E O
UTPU
T
REVE
RSE
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
TQH-33 TQH-34
TQH
-12
1 Ph
ase,
1P/
2W, 1
E, V
ARh
ours
RO2
±0.2
5%SW
112
0V/5
A A
CH
Z660
Hz
OR1
Reed
Rel
ay.
P111
5/23
0 VA
C ±1
5%PU
51
puls
e pe
r VA
RHC
MM
etal
TQH
-13
1 Ph
ase,
1P/
3W, 2
E, V
ARh
ours
RO3
±0.1
%SW
224
0V/5
A A
CH
Z550
Hz
OR2
Reed
Rel
ay.
Forw
ard
+ Re
vers
eP2
24 V
DC
±15%
PU6
10 P
ulse
s Pe
r VA
RHC
PPl
astic
TQH
-33
3 Ph
ase,
3P/
3W, 2
E, V
ARh
ours
SWY
Cust
om In
put
HZ4
400H
zO
C1
Ope
n Co
llect
or.
Forw
ard
only
P312
5 VD
C ±1
5%PU
710
0 pu
lses
per
VA
RH
TQH
-34
3 Ph
ase,
3P/
4W, 3
E, V
ARh
ours
OC
2O
pen
Colle
ctor
. Fo
rwar
d +
Reve
rse
PYCu
stom
Pow
er ±
15%
PU8
1 pu
lse
per 1
000V
ARH
Aux
iliar
y Po
wer
Puls
e pe
r VA
RHou
rIn
put F
requ
ency
Base
Mod
el
Case
Inpu
t Sig
nal
Out
put S
igna
lA
ccur
acy
Forw
ard
only
TQH
Since 1976
(Z670)www.texmate.com 20
MODELS OFFERED
FEATURES
TQQH-12: 1 Phase, 2 Wire – 1 ElementTQQH-13: 1 Phase, 3 Wire – 2 ElementTQQH-33: 3 Phase, 3 Wire – 2 ElementTQQH-34: 3 Phase, 4 Wire – 3 Element
• Uses Time Division Multiplication (TDM) for precision measurement of even distorted signals.• High accuracy ±0.2% of Rated Output (R.O.)• Super high accuracy ±0.1% of Rated Output (R.O.) available as a special order.*• High immunity to external noise.• Quick and easy mounting to 35mm DIN Rail (DIN46277) or screw mounting.• Many input and output signal combinations.
VARs+VAR Hours TRANSDUCERS
• Accurate measurement of the reactive power and reactive energy (VARs and VARHours) of a three phase system with balanced or unbalanced loads.
• The output signals are isolated load independent pulses, repre-senting the measured value of the reactive energy (VARHours, forward and reverse) and DC mA or DC mV for the reactive power (VAR).
GENERAL SPECIFICATIONSAccuracy ................................... ± 0.2% R.O. Standard for 10 to 100% of rated output
± 0.1% R.O. (Special Option)Temp. coefficient ..................... ≤100ppm/ºC of span
≤60ppm/ºC for ambient temperature of 25ºC ±10ºCTemp. range .............................. Storage temperature range -20ºC to 60ºC (-4ºF to 140ºF)
Operating temperature range 0ºC to 50ºC (32ºF to 122ºF)Humidity range ........................ Up to 95% RH non condensingIsolation .................................... Between Input/Output/Power/CaseDielectric test ........................... DIN-IEC 688
2K Vrms/1 min, Between terminal to terminal 2.8K Vrms/1 min, Between terminal to case
Surge test ................................. DIN-IEC 255-4, ANSI C37 90a/1974 5KV(1.2x50 µs)Insulation Resistance ............. Greater than 100 M Ω at 500V DCHousing material ..................... ABS Resin(94V-0) or metalMounting ................................... Screw mount on metal case or Plastic case on DIN Rail 35mmAuxiliary Power ........................ AC 115/230V ± 15%, 50/60Hz, 3VA
DC 24V ± 20%(optional) 125V DC ± 20%(optional)
INPUT SPECIFICATIONSAC Input .................................... 120V/5A AC, 240V/5A AC. Custom input (600V max /10A AC max)Frequency ................................. 60Hz ±3Hz, 50Hz ±3Hz, 400Hz ±3Hz Burden ...................................... ≤0.2VA per current circuit, ≤0.1VA per voltage circuit.Response Sensitivity .............. ≤0.5% of measuring range to maximum input rangeInput Voltage ............................ 600V AC rms continuous (absolute maximum)
Overload Capacity 1.25 times the rated input Voltage continuously. 2 times the rated input Voltage for 10 secs. 4 times the rated input Voltage for 5 secs.
Input Current ............................ 3 times the rated input current continuously. Overload Capacity 10 times the rated input current for 10 secs. 50 times the rated input current for 1 sec. 80 times the rated input current for 0.5 secs
TQQH
Since 1976
(Z670)www.texmate.com 21
Output Variables ................. Pulses (VARHours) and DC mA or DC V (VARs)Ripple ................................... < 0.5% of rated output. Peak to Peak (maximum)Response Time ................... < 400 milliseconds to go from 0 to 99% of outputZero Adjustment ................. ± 5% of rated output (minimum)Span Adjustment ................ ± 10% of rated output (minimum)
To calculate the actual VARHours and VARs for each output pulse, the CT and PT ratios have to be factored in VARs = (CT Ratio) X (PT Ratio) x Nominal Watts
VARHours per Output Pulse = (CT Ratio) X (PT Ratio) Nominal Pulses /VARHour
Calculation example: For Single phase 2 wire, TQQH-12If CT = 200A:5A then CT Ratio = 40 PT is 3300V:110V then PT Ratio = 30
VARs = 30 x 40 x 500 = 600kVAR
If 1 pulse per VARHour is selected, the output will actually be 1 pulse per 1200 VARHoursIf 10 pulse per VARHour is selected, the output will actually be 1 pulse per 120 VARHoursIf 100 pulse per VARHour is selected, the output will actually be 1 pulse per 12 VARHours
VARs+VAR Hours TRANSDUCERS
OUTPUT SPECIFICATIONS
CONNECTION DIAGRAM
+ +
ACPOWER230 V
115 V
L C.T.1
P2P1
1S 1L 3S 3L
P.T.1
N
+ +FORW
ARD
PULS
E O
UTPU
T
REVE
RSE
PULSEOUTPUT
+DC
OUTPUT
DCOUTPUT+
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
PULSEOUTPUT
+ +
ACPOWER230 V
115 V
L1 C.T.1
P2 P3P1
1S 1L 3S 3L
C.T.3
P.T.1 P.T.3
N
L2
+ +FORW
ARD
PULS
E O
UTPU
T
REVE
RSE
+DC
OUTPUT
DCOUTPUT+
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
TQQH-12 TQQH-13
ACPOWER230 V
115 V
L1 C.T.1
P2 P3P1
1S 1L 3S 3L
C.T.3
P.T.1 P.T.3
L2
L3
PULSEOUTPUT
+ +
+ +FORW
ARD
PULS
E O
UTPU
T
REVE
RSE
+DC
OUTPUT
DCOUTPUT
+
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
ACPOWER230 V
115 V
L1C.T.1
P2 P3P1P0
1S 1L 2S 2L 3S 3L
C.T.3C.T.2
P.T.
2
P.T.
1
P.T.
3
L2
L3
N
PULSEOUTPUT
+ +
+ +FORW
ARD
PULS
E O
UTPU
T
REVE
RSE
+DC
OUTPUT
DCOUTPUT
+
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
TQQH-33 TQQH-34 TQQ
H-1
21
Phas
e, 1
P/2W
, 1E,
VA
R+VA
Rhou
rsRO
2±0
.25%
SW1
120V
/5A
AC
HZ6
60H
zO
QR4
VARs
±
1 m
A D
CVA
RHr
Reed
Rel
ay. F
orw
ard
only
P111
5/23
0 VA
C ±1
5%PU
51
puls
e pe
r VA
RHC
MM
etal
TQQ
H-1
31
Phas
e, 1
P/3W
, 2E,
VA
R+VA
Rhou
rsRO
3±0
.1%
SW2
240V
/5A
AC
HZ5
50H
zO
QR5
VARs
1
2±8m
A D
CVA
RHr
Reed
Rel
ay. F
orw
ard
and
Reve
rse
P224
VD
C ±1
5%PU
610
Pul
ses P
er V
ARH
CP
Plas
tic
TQQ
H-3
33
Phas
e, 3
P/3W
, 2E,
VA
R+VA
Rhou
rsSW
YCu
stom
Inpu
tH
Z440
0Hz
OQ
C4
VARs
±1m
A D
CVA
RHr
Ope
n Co
llect
or. F
orw
ard
only
P312
5 VD
C ±1
5%PU
710
0 pu
lses
per
VA
RH
TQQ
H-3
43
Phas
e, 3
P/4W
, 3E,
VA
Rs+V
ARh
ours
O
QC
5VA
Rs 1
2 ±
8mA
DC
VARH
r O
pen
Colle
ctor
. For
war
d +
Reve
rse
PYCu
stom
Pow
er ±
15%
PU8
1 pu
lse
per 1
000V
ARH
Base
Mod
el
Inpu
t Sig
nal
Out
put S
igna
lIn
put F
requ
ency
Acc
urac
yA
uxili
ary
Pow
erCa
sePu
lse
per V
ARH
our
TQQH
Since 1976
(Z670)www.texmate.com 22
MODELS OFFERED
FEATURES
AC Power Factor TRANSDUCERS
• Uses Time Division Multiplication (TDM) for precision measurement of even distorted signals.• High accuracy ±0.5% of Rated Output (R.O.). • High immunity to external noise.• Quick and easy mounting to 35mm DIN Rail (DIN46277) or screw mounting.• Many input and output signal combinations.
TPF-12: 1 Phase, 2 Wire – 1 ElementTPF-33: 3 Phase, 3 Wire – 2 ElementTPF-34: 3 Phase, 4 Wire – 3 Element
• Accurate measurement of the Power Factor (Cos φ) of a three phase system with balanced or unbalanced loads.
• The output signals are isolated load independent DC mA or DC V, representing the measured value of the Power Factor (Cos φ).
GENERAL SPECIFICATIONSAccuracy ................................... ± 0.2% R.O. Standard for 10 to 100% of rated output
± 0.1% R.O. (Special Option)Temp. coefficient ..................... ≤100ppm/ºC of span
≤60ppm/ºC for ambient temperature of 25ºC ±10ºCTemp. range .............................. Storage temperature range -20ºC to 60ºC (-4ºF to 140ºF)
Operating temperature range 0ºC to 50ºC (32ºF to 122ºF)Humidity range ........................ Up to 95% RH non condensingIsolation .................................... Between Input/Output/Power/CaseDielectric test ........................... DIN-IEC 688
2K Vrms/1 min, Between terminal to terminal 2.8K Vrms/1 min, Between terminal to case
Surge test ................................. DIN-IEC 255-4, ANSI C37 90a/1974 5KV(1.2x50 µs)Insulation Resistance ............. Greater than 100 M Ω at 500V DCHousing material ..................... ABS Resin(94V-0) or metalMounting ................................... Screw mount on metal case or Plastic case on DIN Rail 35mmAuxiliary Power ........................ AC 115/230V ± 15%, 50/60Hz, 3VA
DC 24V ± 20%(optional) 125V DC ± 20%(optional)
INPUT SPECIFICATIONSMeasuring Range ............... Power Factor
Lead (capacitive) 0.5 …. 1 …. Lag (Inductive) 0.5AC Voltage Input ................. 30 to 600VAC Current Input................. 0 to 5A ACFrequency ........................... 60Hz ±3Hz, 50Hz ±3Hz, 400Hz ±3Hz Burden ................................. ≤0.2VA per current circuit, ≤0.1VA per voltage circuit.Response Sensitivity ......... ≤0.5% of measuring range to maximum input rangeInput Voltage ...................... 600V AC rms continuous (absolute maximum)
Overload Capacity 1.25 times the rated input Voltage continuously. 2 times the rated input Voltage for 10 secs. 4 times the rated input Voltage for 5 secs.
Input Current ...................... 3 times the rated input current continuously. Overload Capacity 10 times the rated input current for 10 secs. 50 times the rated input current for 1 sec. 80 times the rated input current for 0.5 secs
TPF
Since 1976
(Z670)www.texmate.com 23
AC Power Factor TRANSDUCERS
ACPOWER230 V
115 V
L1 C.T.1
P2P1
1S 1L 3S 3L
P.T.1
N
+DC
OUTPUT
DCOUTPUT
+
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
Output Variables ................. DCmA or DCV (Power Factor. Cos φ)Ripple ................................... < 0.5% of rated output. Peak to Peak (maximum)Response Time ................... < 400 milliseconds to go from 0 to 99% of outputZero Adjustment ................. ± 5% of rated output (minimum)Span Adjustment ................ ± 10% of rated output (minimum)
OUTPUT SPECIFICATIONS
CONNECTION DIAGRAM
TPF-12
TPF-33 TPF-34ACPOWER230 V
115 V
L1 C.T.1
P2 P3P1
1S 1L 3S 3L
C.T.3
P.T.1 P.T.3
L2
L3
PULSEOUTPUT
+ +
+ +FOR
WAR
D
PULS
E O
UTP
UT
REV
ERSE
+DC
OUTPUT
DCOUTPUT
+
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
ACPOWER230 V
115 V
L1C.T.1
P2 P3P1P0
1S 1L 2S 2L 3S 3L
C.T.3C.T.2
P.T.
2
P.T.
1
P.T.
3
L2
L3
N
PULSEOUTPUT
+ +
+ +FOR
WAR
D
PULS
E O
UTP
UT
REV
ERSE
+DC
OUTPUT
DCOUTPUT
+
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
TPF-
121
Phas
e, 1
P/2W
, 1E,
Pow
er F
acto
rRO
6±0
.5%
SW1
120V
/5A
AC
HZ6
60H
zO
PF1
±1 m
A D
C,
0-1-
0 PF
LGLA
G =
+ P
olar
ityTP
F-33
3 Ph
ase,
3P/
3W, 2
E, P
ower
Fac
tor
RO5
±0.3
%SW
224
0V/5
A A
CH
Z550
Hz
OPF
24
to 2
0mA
DC
0-1
-0 P
FLD
LEA
D=
+Pol
arity
TPF-
343
Phas
e, 3
P/4W
, 3E,
Pow
er F
acto
rSW
YCu
stom
Inpu
tH
Z440
0Hz
OPF
A±1
mA
DC,
0
.5 -
1 - 0
.5 P
FO
PFB
4 to
20m
A D
C 0
.5 -
1 - 0
.5 P
F
Base
Mod
el
Aux
iliar
y Po
wer
Inpu
t Sig
nal
Inpu
t Fre
quen
cyA
ccur
acy
Out
put S
igna
lIn
put/
Out
put
Rela
tions
hip
CM
Met
alC
PPl
astic
Case
P1P011
5/23
0V A
C ±1
5%Si
ngle
Pow
ered
P224
V D
C ±1
5%
P312
5V D
C ±1
5%Cu
stom
Pow
er ±
15%
PY
TPF
Since 1976
(Z670)www.texmate.com 24
MODELS OFFERED
FEATURES
FREQUENCY TRANSDUCERS
• High accuracy ±0.05% of Rated Output (R.O.). • Frequency range from 45 Hz to 10KHz. • High immunity to external noise.• Quick and easy mounting to 35mm DIN Rail (DIN46277) or screw mounting.• Many input and output signal combinations.
TF-1: Frequency
GENERAL SPECIFICATIONS
Accuracy ............................. ± 0.2% R.O. Standard for 10 to 100% of rated output ± 0.1% R.O. (Special Option)
Temp. coefficient ................ ≤100ppm/ºC of span ≤60ppm/ºC for ambient temperature of 25ºC ±10ºC
Temp. range ........................ Storage temperature range -20ºC to 60ºC (-4ºF to 140ºF) Operating temperature range 0ºC to 50ºC (32ºF to 122ºF)
Humidity range ................... Up to 95% RH non condensingIsolation ............................... Between Input/Output/Power/CaseDielectric test ...................... DIN-IEC 688
2K Vrms/1 min, Between terminal to terminal 2.8K Vrms/1 min, Between terminal to case
Surge test ............................ DIN-IEC 255-4, ANSI C37 90a/1974 5KV(1.2x50 µs)Insulation Resistance ........ Greater than 100 M Ω at 500V DCHousing material ................ ABS Resin(94V-0) or metalMounting ............................. Screw mount on metal case or Plastic case on DIN Rail 35mmAuxiliary Power................... AC 115/230V ± 15%, 50/60Hz, 3VA
DC 24V ± 20%(optional) 125V DC ± 20%(optional)
TF
• Accurate measurement of the Frequency of a single or three phase system with balanced or unbalanced loads.
• The output signals are isolated load independent DC mA or DC V, representing the measured value of the Frequency.
Since 1976
(Z670)www.texmate.com 25
+DC
OUTPUT
OUTPUT+ INPUT
+12V Auxiliary
Power for Sensor
ACPOWER230 V
115 V
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
Output Variables ................. DCmA or DCVRipple ................................... < 0.5% of rated output. Peak to Peak (maximum)Response Time ................... < 400 milliseconds to go from 0 to 99% of outputZero Adjustment ................. ± 5% of rated output (minimum)Span Adjustment ................ ± 10% of rated output (minimum)Load Resistance ................. 10 kΩ maximum for 0 to 1mA output
500 Ω maximum for 4 to 20mA output 500 Ω minimum for 0 to 10V output
FREQUENCY TRANSDUCERS
OUTPUT SPECIFICATIONS
CONNECTION DIAGRAM
TF-1
1 Ph
ase,
1P/
2W,
Freq
uenc
yRO
7±0
.1%
SF1
80V
to 6
00V
AC
HZ2
45H
z to
55H
zO
HZ1
0 to
1 m
A D
CP1
115/
230
VAC
±15%
RO4
±0.0
5%SF
22V
to 3
0V A
C/D
CH
Z355
Hz
to 6
5Hz
OH
Z24
to 2
0mA
DC
P224
VD
C ±1
5%H
Z145
Hz
to 6
5Hz
OH
Z40±
1mA
DC
P312
5 VD
C ±1
5%H
ZYCu
stom
inpu
t Fq
rang
eO
HZY
Cust
om O
utpu
tPY
Cust
om P
ower
±15
%
Base
Mod
el
Inpu
t Sig
nal
Out
put S
igna
lA
uxili
ary
Pow
erIn
put F
requ
ency
Acc
urac
y
CM
Met
alC
PPl
astic
Case
TF
AC Voltage Input range ...... 2V to 200V AC or 30 to 600V ACFrequency ........................... 60Hz ±3Hz, 50Hz ±3Hz, 400Hz ±3Hz Burden ................................. ≤0.2VA per current circuit, ≤0.1VA per voltage circuit.Response Sensitivity ......... ≤0.5% of measuring range to maximum input rangeInput Voltage ....................... 600V AC rms continuous (absolute maximum)
Overload Capacity 1.25 times the rated input Voltage continuously. 2 times the rated input Voltage for 10 secs. 4 times the rated input Voltage for 5 secs.
INPUT SPECIFICATIONS
Since 1976
(Z670)www.texmate.com 26
MODELS OFFERED
FEATURES
TD-1: DC Volts or mA
GENERAL SPECIFICATIONSAccuracy ............................. ± 0.1% R.O. Temp. coefficient ................ ≤100ppm/ºC of span
≤60ppm/ºC for ambient temperature of 25ºC ±10ºCTemp. range ........................ Storage temperature range -20ºC to 60ºC (-4ºF to 140ºF)
Operating temperature range 0ºC to 50ºC (32ºF to 122ºF)Humidity range ................... Up to 95% RH non condensingIsolation ............................... Between Input/Output/Power/CaseDielectric test ...................... DIN-IEC 688
2K Vrms/1 min, Between terminal to terminal 2.8K Vrms/1 min, Between terminal to case
Surge test ............................ DIN-IEC 255-4, ANSI C37 90a/1974 5KV(1.2x50 µs)Insulation Resistance ........ Greater than 100 M Ω at 500V DCHousing material ................ ABS Resin(94V-0) or metalMounting ............................. Screw mount on metal case or Plastic case on DIN Rail 35mmAuxiliary Power................... AC 115/230V ± 15%, 50/60Hz, 3VA
DC 24V ± 20%(optional) 125V DC ± 20%(optional)
DC Volts or mA TRANSMITTER ISOLATOR
• High accuracy ±0.2% of Rated Output (R.O.)• High immunity to external noise.• Quick and easy mounting to 35mm DIN Rail (DIN46277)• Many input and output signal combinations
TD
• The DC to DC Isolation Transmitter can receive various DC Voltage or Current signals and can output desired voltage or current signals isolated from each other
Since 1976
(Z670)www.texmate.com 27
Output Variables ................. DC Voltage (0~10V) DC Current (0~20mA)
Response Time ................... < 400 milliseconds to go from 0 to 99% of outputZero Adjustment ................. ± 5% of rated output (minimum)Span Adjustment ................ ± 10% of rated output (minimum)
OUTPUT SPECIFICATIONS
CONNECTION DIAGRAM
TD
TD-1
DC
Volts
or m
ARO
7±0
.1%
SD1
0 to
1m
A D
CO
D1
0 to
1m
A D
CP1
115/
230
VAC
±15%
SD2
4 to
20m
A D
CO
D2
4 to
20m
A D
CP2
24 V
DC
±15%
SD
30
to 1
V D
CO
D3
0 to
10V
DC
P312
5 VD
C ±1
5%SD
40
to 1
0V D
CO
DYCu
stom
Out
put
PYCu
stom
Pow
er ±
15%
SDY
Cust
om In
put (
600V
max
)
Aux
iliar
y Po
wer
Base
Mod
el
Inpu
t Sig
nal
Acc
urac
yO
utpu
t Sig
nal
CM
Met
alC
PPl
astic
Case
1 2 3 4
5 6 7 8
OUTPUT INPUT
POWER
+
230 V115 V
OUTPUT+
INPUT+
Metal Case Plastic Din Rail
1 2 3 4
5 6 7 8
OUTPUT
INPUT
POWER
INPUT+
+
DC Voltage .......................... 0 to 600VDC Current .......................... for current input can be obtained from shunt
INPUT SPECIFICATIONS
DC Volts or mA TRANSMITTER ISOLATOR
Since 1976
(Z670)www.texmate.com 28
CASE DIMENSIONS
Fire Retardant, ABS Case DIN Rail Mounting
4.32
” (1
07.5
mm
)
4.95
” (1
25.7
mm
)
0.6” (15.2mm)
1.38” (35mm) Rail (DIN 46277)
3.15” (80mm)
2.36
” (6
0mm
)
Case C
Metal Case, Screw Mounting4.
09"
(104
mm
)
4.84
" (1
23m
m)
1.
50"
(38.
1mm
)
2.2
8" (5
8mm
)
4.06" (103mm)
3.50" (89mm)
3.03" (77mm)
No.8-36UNFM4 Screw
Case A
450 State Place, Escondido, CA 92029 • For ordering info call: 1-800-TEXMATE (1-800-839-6283) or 760 598-9899• Email: [email protected] • 24 Hours • Fax: (760) 598-9828 •• For tech assistance call: (760) 598-9899
Copyright © 2016 Texmate Inc. All Rights Reserved.
CASE DIMENSIONS - CASE A & C
Since 1976
(Z670)www.texmate.com 29
CASE DIMENSIONS
Fire Retardant, ABS Case DIN Rail Mounting
Case BMetal Case, Screw Mounting
Case D
4.80" (122 mm)
0.748" (19 mm)
5.55
" (1
41m
m)
4.75" (120.65mm)
5.35" (136 mm)
4.33" (110 mm)
1.50"(38.1 m
m)
2.83" (72 mm
)
3.74" (95 mm
)
No.8-36UNFM4 Screw
3.74
” (9
5.0m
m)
4.45” (113.0mm)
5.02
” (1
27.5
mm
)
5.74
” (1
45.7
mm
)
0.6” (15.2mm)
1.38” (35mm) Rail (DIN 46277)
450 State Place, Escondido, CA 92029 • For ordering info call: 1-800-TEXMATE (1-800-839-6283) or 760 598-9899• Email: [email protected] • 24 Hours • Fax: (760) 598-9828 •• For tech assistance call: (760) 598-9899
Copyright © 2016 Texmate Inc. All Rights Reserved.
CASE DIMENSIONS - CASE B & D