2
VIDEO INSTRUCTIONS For best results follow video instructions at www.decibullz.com/high-fidelity-instructions HEAT MICROWAVE If using the microwave, fill two glass or ceramic cups with 3 to 4 inches of water and bring to a boil. DO NOT PLACE THE MOLD IN THE MICROWAVE WITH THE WATER AND DO NOT USE PAPER, PLASTIC, OR STYROFOAM CUPS. STOVE TOP OR KETTLE If using the stove top or kettle, boil water, remove from heat and fill each cup with 3 to 4 inches of hot water. ASSEMBLY Attach correct size silicone tips to Thermo Fit Molds. Medium tips work for most people. You can change the tips after the molding process is complete. Check that the tip is securely attached before inserting into your ear. If the tip becomes dislodged in the ear canal, seek medical attention. Place ONE mold in each cup. Multiple molds WILL stick together if heated at the same time. Let molds sit in the hot water for 5 minutes. CUSTOM MOLDED HIGH FIDELITY EARPLUGS IMPROPER FITTING OR MISUSE WILL REDUCE EFFECTIVENESS OF EARPLUGS AND COULD RESULT IN HEARING LOSS OR INJURY Test thoroughly in progressively louder environments. Wear hearing protection at all times that you are exposed to loud noise. The filter should reduce ambient volume slightly, you can test this by talking loudly. You should be able to hear your voice clearly, but at a reduced volume, and the noises around you should not sound as loud. If at any time you feel your hearing protection is not providing adequate protection, remove yourself from the loud environment immediately. WARNING! CAUTION: CHOKING HAZARD Keep away from children. Parts are nontoxic but may interfere with breathing if caught in windpipe. WHAT IS INCLUDED MATERIALS NEEDED FOR MOLDING CONTACT US If you have any questions or need additional support please contact us: [email protected] Left and Right Thermo-fit Molds 1 Set of Decibullz High Fidelity Filters S, M, L Triple Flange Silicone Tips Carrying Pouch Decibullz Thermo Fit Molds Decibullz High Fidelity Filters Silicone Tips Metal Spoon 2 Glass or Ceramic Cups/Mugs – or – Metal Pan (Stovetop) Boiling Water Timer Mirror (recommended) 1 2 3 4 SILICONE TIP CUSTOM MOLD SHAPE Insert the filter into the back of the mold and place the earplug into your ear. CAUTION: DO NOT PLACE THE MOLD INTO EAR WHILE IT IS HOT. WAIT UNTIL THE MOLD IS WARM AND PLIABLE. Firmly press the back of the filter making sure the silicone tip fits into the ear canal. Remove the mold with a metal spoon and let cool for 30 seconds. CAUTION: ITEMS MAY BE VERY HOT. Be sure to use a metal spoon, the mold WILL stick to plastic. With the pad of your finger, press the mold to fill the concha (bowl) of your ear. If the molding material is not fully softened or you feel the center of the mold is still firm, reheat the mold in hot water. REMOLDING To re-mold, remove the filter, place the mold back in boiling water for 5 minutes, then repeat steps 4-7. TESTING YOUR EARPLUGS: IMPROPER FITTING OR MISUSE WILL REDUCE EFFECTIVENESS OF EARPLUGS AND COULD RESULT IN HEARING LOSS OR INJURY It is extremely important to test your earplugs in progressively louder environments. You can do this by gradually increasing your noise exposure. The filter should reduce ambient volume slightly, you can test this by talking loudly. You should be able to hear your voice clearly, but at a reduced volume, and the noises around you should not sound as loud. If at any time you feel that your earplugs are not providing adequate protection, remove yourself from the loud environment immediately. ENJOY YOUR DECIBULLZ! 5 7 8 6 CONCHA Let the mold cool for 5 minutes before removing. Repeat the process with the other ear. Excessive heat can deform the earplugs. Do not leave in a hot car, direct sunlight, or anywhere with excessive heat.
