Flint Powertrain nortH #2

Hilco Industrial, LLC

WebCast/OnsIte auCtIOn

A u c t i o n e e r s • L i q u i d a t o r s • A p p r a i s e r s

Hilco Industrial, LLC

www.hilcoind.com

Atlanta • Birmingham • Birmingham (UK) • Boston • Charlotte • Chicago • Connecticut • Dallas • Detroit • Grand Rapids

Guadalajara (MX) • Hong Kong (Greater China) • Irapuato (MX) • Leeds (UK) • London (UK) • Los Angeles • Mexico City (MX)

Monterrey (MX) • New York • San Francisco • Singapore • Thailand • Toronto • Villahermosa (MX)

to schedule an auction, please call Hilco Industrial, LLC at 1-877-37-HILCO (44526)2

(9) HiGH SPeeD StraiGHt SiDe PreSSeS(3) #1, #2 & #4 PreSS lineS, eacH incluDinG:1 – MINSTER PIECE-MAKER PM3-125-48 125-TON HIGH SPEED STRAIGHT

SIDE PRESS, S/Ns 24903, 24902, 24901, 125-Ton, Bed Size 48” LR x 32”FB, Speeds Variable 0 – 500 SPM, Stroke 3”, Slide Adjustment 2”, ShutHeight 19” Over Bed / 14” Over Bolster, 15” Wide Windows, Air Clutch, AirCounterbalance, Floor Standing With Dynamics Micro / Level Isolator Pads,Minster Console Control, Acon Insulated Panel Noise Suppression Enclosure

1 – VAMCO MODEL BK2-6 II 6” ADJUSTABLE CAM PRESS MOUNTED ROLLFEED, S/Ns BK264615L22R, SBK264451511R, BK264615L21R

1 – PERFECTO / MINSTER 2400-12-17-MHS 12” ROLL STRAIGHTENER, S/N 13-11073 VENDOR S/N S2-80216, S/N 13-11071, VENDOR S/N S2-80214, S/N 13 11072, VENDOR S2-80215

1 – LITTELL 40-12 DOUBLE-END AUTOMATIC CENTERING REEL / UNCOILER, S/Ns 85492-81, 85492-81, N/A, Maximum Coil Weight 4000-Lbs., Max. Coil Width 12”, Max. OD 60”, ID Range 19-24”, ManualExpansion, Pneumatic Drag Brake

(3) #3, #8, #9 PreSS lineS, eacH incluDinG:1 – MINSTER PIECE-MAKER P2-100-48 100-TON HIGH SPEED STRAIGHT

SIDE PRESS, S/Ns 23792, 24708, 24433, 100-Ton, Bed Size 48” LR x 32”FB, Speeds Variable 100 – 400 SPM, Stroke 2”, Adjustment 2”, Shut Height19.5”, 16” Wide Windows, Air Clutch, Air Counterbalance, Floor StandingWith Dynamics Micro / Level Isolator Pads, Minster Console Control, AconInsulated Panel Noise Suppression Enclosure

1 – MINSTER 6” PRESS MOUNTED ROLL FEEDER

1 – PERFECTO / MINSTER 2400-12-17 12” ROLL STRAIGHTENER, S/N MHS-1031, VENDOR S2-78173, S/N 13-11058, VENDOR S2-80024,S/N 13-11015, VENDOR S2-79154

1 – LITTELL MODEL 40-12 DOUBLE-END AUTOMATIC CENTERING REEL /UNCOILER, S/Ns 85212-79, 85446-80, 85408-80, Maximum Coil Weight4000-Lbs., Max. Coil Width 12”, Max. OD 60”, ID Range 19-24”, ManualExpansion, Pneumatic Drag Brake

#6 PreSS line, incluDinG:1 – MINSTER PIECE-MAKER P2-100-48 100-TON HIGH SPEED STRAIGHT

SIDE PRESS, S/N 24710, 100-Ton, Bed Size 48” LR x 32” FB, SpeedsVariable 100 – 400 SPM, Stroke 2”, Adjustment 2”, Shut Height 19.5”, 16”Wide Windows, Air Clutch, Air Counterbalance, Floor Standing WithDynamics Micro / Level Isolator Pads, Minster Console Control, AconInsulated Panel Noise Suppression Enclosure

1 – VAMCO QUANTUM 6, 6” PRESS MOUNTED SERVO ROLL FEED, S/N 062.52C63, Programmable Console Control

1 – PERFECTO / MINSTER 2400-12-MHS 12” ROLL STRAIGHTENER, S/N 13-11059, VENDOR S/N S2-80026

1 – LITTELL MODEL 40-12 DOUBLE-END AUTOMATIC CENTERING REEL /UNCOILER, S/N 85446-80, Maximum Coil Weight 4000-Lbs., Max. CoilWidth 12”, Max. OD 60”, ID Range 19-24”, Manual Expansion, PneumaticDrag Brake

Flint Powertrain nortH #2

auCtIOn LOCatIOngenesys COnFerenCe & banquet Center801 HeaLtH parK bLvd. • grand bLanC, mI 48439

dIreCtIOns tO auCtIOnFrOm bIsHOp InternatIOnaL aIrpOrt: Head West tOWard W brIstOL rd. turn rIgHtat W brIstOL rd. sLIgHt rIgHt tO merge OntO I-75 s/us-23 s tOWard detrOIt/annarbOr. COntInue tO FOLLOW I-75 s FOr 7.3 mILes and taKe exIt 108 FOr HOLLy rd.turn rIgHt at HOLLy rd. and taKe tHe 2nd rIgHt OntO HeaLtH parK bLvd.

prevIeW LOCatIOn902 HamILtOn st. • FLInt, mI 48550

dIreCtIOns tO prevIeWFrOm bIsHOp InternatIOnaL aIrpOrt: Head east tOWard W brIstOL rd. turn rIgHt atW brIstOL rd. maKe a sLIgHt rIgHt OntO tHe us-23 n/I-75 n ramp tO sagInaW. COntInuetOWard I-69 e. Keep rIgHt at tHe FOrK, FOLLOW sIgns FOr I-69 e/FLInt/pOrt HurOn andmerge OntO I-69 e. prOCeed FOr 3.3 mILes and taKe exIt 137 tO merge OntO I-475 ntOWard sagInaW. gO 1.9 mILes and taKe exIt 8b FOr davIsOn rd tOWard HamILtOn ave.turn LeFt at brOadWay bLvd. COntInue OntO e HamILtOn ave.

FrOm tHe detrOIt area: taKe I-75 nOrtH tOWards FLInt. apprOaCHIng FLInt, taKe I-475 nOrtH. FOLLOW I-475 nOrtH tO exIt #8b, davIsOn rOad/HamILtOn avenue. turnLeFt at brOadWay bLvd. and COntInue OntO HamILtOn avenue. turn IntO tHe gmpOWertraIn COmpLex and CHeCK In WItH seCurIty FOr FurtHer InstruCtIOns.

auCtIOn datetuesday, Janaury 18tH

begInnIng at 10am LOCaL tIme

prevIeW datemOnday, January 17tH

9am tO 4pm LOCaL & mOrnIng OF saLe

FurtHer InFOrmatIOn• a buyers premIum OF 13.5% FOr aLL OnsIte saLes &

16% FOr aLL WebCast saLes WILL be In eFFeCt.auCtIOn WILL be COnduCted In engLIsH, aCCeptIngu.s. CurrenCy OnLy.

• The removal deadling for The Spline rollerS,CenTerleSS grinderS &  ToCCo induCTion ShafThardnerS iS monday, January 31, 2010. all oTherequipmenT The removal deadline iS friday, february11, 2010 WiTh hourS of removal beTWeen 8am To 4pmmonday Thru friday. afTer The noTed deadline aT4pm The buyer Will inCur a CoST of $500 for enTryinTo The faCiliTy.

• FOr FurtHer InFOrmatIOn On maCHInery & equIpment,pLease COntaCt Ken pLanet at 248.254.9999 x33 OremaIL KpLanet@HILCOInd.COm Or marIO mazzuCa at248.569.9781 Or marIO@maynards.COm

• FOr payments pLease COntaCt beCKy KuznICKI at517.719.8134 Or emaIL beCKy@maynards.COm

• CustOmer servICe, pLease COntaCt sandI neeLy at248.254.9999 x16 Or emaIL sneeLy@HILCOInd.COm

• remOvaL OF Items Is Open tO rIgger OF CHOICe WItH tHe FOLLOWIng requIrements: InsuranCe OF $1 mILLIOn COmpreHensIve and $2 mILLIOn LIabILIty.

HILCO IndustrIaL, LLC WebCast/OnsIte auCtIOn

For more information, please visit us on the web at www.hilcoind.com 3

press LInes • CnC turnIng & maCHInIng Centers

(9) HiGH SPeeD StraiGHt SiDe PreSSeS (continueD)#7 PreSS line, incluDinG:1 – MINSTER PIECE-MAKER P2-100-48 100-TON HIGH SPEED STRAIGHT SIDE PRESS, S/N 24709,

100-Ton, Bed Size 48” LR x 32” FB, Speeds Variable 100 – 400 SPM, Stroke 2”, Adjustment 2”, Shut Height19.5”, 16” Wide Windows, Air Clutch, Air Counterbalance, Floor Standing With Dynamics Micro / Level IsolatorPads, Minster Console Control, Acon Insulated Panel Noise Suppression Enclosure

1 – MINSTER 6” PRESS MOUNTED ROLL FEEDER, S/N N/A

1 – PERFECTO / MINSTER 2400-12-MHS 12” ROLL STRAIGHTENER, S/N 13-11057, VENDOR S2-80023

1 – LITTELL MODEL 40-12 DOUBLE-END AUTOMATIC CENTERING REEL / UNCOILER, S/N 85446-80,Maximum Coil Weight 4000-Lbs., Max. Coil Width 12”, Max. OD 60”, ID Range 19-24”, Manual Expansion,Pneumatic Drag Brake

#10 PreSS line, incluDinG:1 – MINSTER PIECE-MAKER P2-100-48 100-TON HIGH SPEED STRAIGHT SIDE PRESS, S/N 23791,

100-Ton, Bed Size 48” LR x 32” FB, Speeds Variable 100 – 400 SPM, Stroke 2”, Adjustment 2”, Shut Height19.5”, 16” Wide Windows, Air Clutch, Air Counterbalance, Floor Standing With Dynamics Micro / Level IsolatorPads, Minster Console Control,

1 – VAMCO QUANTUM 6 6” PRESS MOUNTED SERVO ROLL FEED, S/N 062.5C110, Programmable Console Control

1 – PERFECTO / MINSTER 2400-12-17 12” ROLL STRAIGHTENER, S/N MHS-1032, VENDOR S2-78174

1 – LITTELL 40-12 DOUBLE-END AUTOMATIC CENTERING REEL / UNCOILER, S/N 85211-78, Maximum CoilWeight 4000-Lbs., Max. Coil Width 12”, Max. OD 60”, ID Range 19-24”, Manual Expansion, Pneumatic Drag Brake

cnc turninG / MillinG center1 – MAZAK SUPER QUICK TURN 28 MS CNC TURNING / MILLING CENTER, S/N 110612 (1994), Mazatrol

T32-3, 12- Position Tool Turret With Live Tooling, Estimated 20” Swing, Est. 48” Between Centers, PowerTailstock, Coolant, Chip Conveyor

(11) cnc turninG centerS9 – OKUMA TYPE CADET MODEL LNC-8W 2-AXIS CNC TURNING CENTERS, S/Ns 0704C711, 0704C734,

0704C696 0707C833, 0709C878, 0707C811, 0706C790, 0707C856, 0705C750, Okuma OSP5020L Control,Pick-N-Place Auto Load / Unload, 12-Position Tool Turret, Power Tailstock, Approx. 10” Turning Diameter, Approx.20” Turning Length, Connected Into Central Supplied Coolant System, *Note Some Machines May Be Incomplete

2 – HARDINGE CONQUEST T-51 CS-51 2-AXIS CNC TURNING CENTERS, S/Ns CLT-405-C, CLT-452-C (1995)

cnc rotarY tranSFer MacHineS3 – THYSSEN KRUPP TURMATIC SYSTEMS TYPE TURMAT 36 / 80-RO AUTOMATIC CNC ROTARY

TRANSFER MACHINE, S/Ns 242-50811, 242-50810, S/N 242-50809 (All 2003)

(8) cnc PiSton turninG MacHineS8 – GIDDINGS & LEWIS CNC 2-SPINDLE VERTICAL

PISTON TURNING MACHINES, S/N 94F005A, 94F004A,94F002A, 92F076B, 94F003A, NA, 04F006A, NA, Giddings& Lewis PMC-450 Operator’s Control Pendant Station,Main Control Panel, Automatic Load / Unload – GantryType, (2) Vertical Spindle Chucks With Power Collet Closer,Single 22 KW Spindle Drive Motor, Connected Into CentralSupplied Coolant System, *Note: Some Machines May BeIncomplete

(10) PiSton lineS SortinG taBleS9 – HOHL / BI-FLOW BELT TYPE PARTS SORTER /

UNSCRAMBLER TABLES, S/Ns N/A, 4’ x 12’, (4)Conveyor Belt Lanes

1 – AUTOMATED SYSTEMS INC / BI-FLOW BELT TYPEPARTS SORTER / UNSCRAMBLER TABLE, S/N NA, 6’ x20’ (12) 6” Wide Plastic Conveyor Belts, Main Control Panel

(24) cnc turninG centerS1 – MONARCH METALIST CNC TURNING CENTER,

S/N 53626, General Numeric GNIO Series Control,Estimated 12” Swing x 36” Centers, Power Tailstock, 8-Position Tool Turret, 25-HP

1 – MAZAK QUICK TURN 10 UNIVERSAL CNC TURNINGCENTER, S/N 58266, Mazatrol CAM T-2 Controls,Estimated 8” Swing x 30” Centers, Power Tailstock, 8” Power Chuck, 8-Position Tool Turret, Coolant, Chip Conveyor

4 – HARDINGE CONQUEST VT-200 2-AXIS CNC VERTICALTURNING CENTERS, S/N VL-232-2, VL-235-2, VL-233-2, VL-129-2, GE Fanuc Series 18-T Control, Single 16”Vertical Workpiece Chuck, Turning Diameter (est.) 15.7”,Turning Length (Height) (est.) 19.8”, 12-Position Tool Turret,Pick-N-Place Loader Arm, 18.5 / 22 KW Spindle Motor,*Note: Some Machines May Be Incomplete

18 – HARDINGE CONQUEST VT-200 2-AXIS CNC VERTICALTURNING CENTERS, S/N VL-234-2, VL-237-2, VL-236-2, VL-238-2, VO-140-2, VL-136-2, VL-127-2, VL-138-2, VL-167-2, VL-139-2, VL-135-2, VL-169-2, VL-353-2, VL-363-2,VL-354-2, VL-364-2, VL-366-2, VL-128-2, GE Fanuc Series18-T Control, Single 16” Vertical Workpiece Chuck, TurningDiameter (est.) 15.7”, Turning Length (Height) (est.) 19.8”,12-Position Tool Turret, Pick-N-Place Loader Arm, 18.5 / 22KW Spindle Motor, With Manual Load, Independent PortableCoolant System With Magnetic Chip Conveyor, *Note: SomeMachines May Be Incomplete

cnc Vertical MacHininG center1 – MONARCH CORTLAND VMC-150 CNC VERTICAL

MACHINING CENTER, S/N 87501, GE General NumericFanuc GN-11 Series Control, Table Size 30” x 60”, 40-Position Automatic Toolchanger, Monarch Taper

mILLIng maCHInes • LatHes • drILLs • saWs • grInders

to schedule an auction, please call Hilco Industrial, LLC at 1-877-37-HILCO (44526)4

cnc Vertical MillinG MacHineS1 – TREE 425 MASTER JOURNEYMAN CNC VERTICAL MILLING

MACHINE, S/N 9-42-96-6018 (1999), Dynapath Delta Autocon CNCControl, Table Size 12” x 50”, Coolant

1 – TREE 425 JOURNEYMAN CNC VERTICAL MILLING MACHINE, S/N 9-42-90-5045 (1990), Dynapath Systems Delta Series CNC Control,Table Size 12” x 50”, Coolant

MillinG MacHineS1 – CINCINNATI MILACRON 415-16 UNIVERSAL DIAL-TYPE HORIZON-

TAL MILLING MACHINE, S/N 310434073-0002, Type L-L, 16” x 80” Table,Spindle Speeds 16 – 1600 With Variable Speed Control, Vertical HeadAttachment, 3-Axis Readout

1 – CINCINNATI CINOVA 80 307-14 VERTICAL MILLING MACHINE, S/N 31723V5W-6, Table Size 14” x 62”, Spindle Speeds 25 – 2000 RPM,2-Axis Readout

1 – BRIDGEPORT 2-HP VERTICAL MILLING MACHINE, S/N BR-281409,Variable Spindle Speeds 60 – 4200 RPM, Table Size 9” x 48”, Power TableFeed, Power Drawbar, DRO

2 – BRIDGEPORT SERIES I 2-HP VERTICAL MILLING MACHINES, S/Ns 12BR-240167, BR-240163, Variable Spindle Speeds 60 -4200 RPM,Table Size 9” x 48”, Power Table & Saddle Feeds, Column Riser, 2-AxisReadout

1 – BRIDGEPORT 2-HP VERTICAL MILLING MACHINE, S/N 12BR-67564,Variable Spindle Speeds 60 – 4200 RPM, Table Size 9” x 48”, Power TableFeed, Power Knee Elevation, Power Drawbar, Bridgeport ShaperAttachment

latHeS1 – KINGSTON HL-2000 22 / 29” X 90” GAP BED ENGINE LATHE,

S/N 10721105, (12) Spindle Speeds 25 – 1500 RPM, Quick ChangeThreading, 3” Hole Thru-Spindle

1 – CLAUSING COLCHESTER 15” X 36” ENGINE LATHE, S/N 6/0053/35703DD, Spindle Speeds 25 – 2000 RPM, Quick ChangeThreading, Taper Attachment, 2-1/8” Hole Thru-Spindle, Sony 2-Axis Readout

1 – TATUNG 540X1000 21.2” X 39.3” ENGINE LATHE, S/N 724784, SpindleSpeeds 35 – 1000 RPM, Quick Change Threading, 2” Hole Thru-Spindle

2 – HARDINGE DV-59 DOVETAIL BED TOOLROOM LATHES, S/Ns 17434,59-4760-3, Variable Speed 150 – 3500 RPM, 5C Collet Drawbar, CabinetBase With Coolant

DrillS1 – FOSDICK 4’ ARM SENSITIVE RADIAL DRILL, S/N 20945, Spindle Speeds 75 – 1500 RPM,

Power Table Elevation, Power Travels & Clamping

1 – CINCINNATI BICKFORD SUPER SERVICE 21” DRILL PRESS, S/N 1L3104, Sliding Head,Box Column, (12) Geared Spindle Speeds 60 – 1200 RPM

1 – LEELAND-GIFFORD 24” 2-SPINDLE DRILL PRESS, S/N NA, 25” x 37” Adjustable Table

1 – WILTON 20604 20” FLOOR TYPE DRILL PRESS, S/N 59394, (8) Geared Head SpindleSpeeds 120 – 1640 RPM

1 – WALKER TURNER 1112-41 – 20” FLOOR TYPE DRILL PRESS, S/N 00096

BanDSawS1 – TANNEWITZ RHNE 40” VERTICAL BANDSAW, S/N 73242

1 – DOALL METALMASTER 36” VERTICAL BANDSAW, S/N 36421139, Variable Blade Speeds0 – 1600 FPM

1 – HYD-MECH S-20A AUTOMATIC HORIZONTAL METAL CUTTING BANDSAW, S/N 10691545, 12” Capacity, Power Shuttle Infeed & Clamping, Coolant

1 – MARVEL SERIES 8 MARK I UNIVERSAL TILT-FRAME VERTICAL BANDSAW, S/N 821437-W

JiG GrinDer1 – FOSDICK FOSMATIC JIG GRINDER, S/N 83920, Table Size 28” x 56”, 2-Axis Readout

SurFace GrinDerS2 – BROWN & SHARPE 1236 MICROMASTER 12” X 36” HYDRAULIC SURFACE GRINDERS,

S/N 523-1236-2499, Electromagnetic Chuck, Readout, Coolant, S/N 523-1236-277,Electromagnetic Chuck With Neutrofier III Microprocessor Control, Acu-Rite Readout, Coolant

2 – BROWN & SHARPE 1030 MICROMASTER 10” X 30” HYDRAULIC SURFACE GRINDERS,S/Ns 523-1030-2300, 523-1030-2325, Electromagnetic Chuck With Variable Control, Coolant

1 – BROWN & SHARPE 818 TECHMASTER 8” X 18” HYDRAULIC SURFACE GRINDER, S/N 523-1818-1156, Walker Electromagnetic Chuck With Variable Control, Overhead Dresser,Coolant, Heidenhain 2-Axis Readout

3 – BROWN & SHARPE 818 MICROMASTER 8” X 18” HYDRAULIC SURFACE GRINDERS,S/N 523-8186-9112, Electromagnetic Chuck With Neutrofier Variable Control, Coolant, S/N 523-8186-9102, Electromagnetic Chuck, With Flux Master Variable Control, Coolant, Acu-Rite 2-Axis Readout, S/N 523-6181-2313, Electromagnetic Chuck, Power Elevation

rotarY SurFace GrinDer1 – HEALD 16” HORIZONTAL SPINDLE ROTARY SURFACE GRINDER, S/N 35939,

16” Electromagnetic Chuck, Universal Table, 12” Wheel Size, 15-HP, Coolant

Cmms • InspeCtIOn • sHears • bendIng braKes & rOLLs

For more information, please visit us on the web at www.hilcoind.com 5

oD & iD GrinDerS1 – CINCINNATI MILACRON / HEALD 273A UNIVERSAL ID

GRINDER, S/N 910 723A88-0121 (1988), Variable WorkheadSpeeds 0 – 500 RPM, 12” Permanent Magnetic Chuck, RedHead 14,000 RPM ID Spindle

1 – BROWN & SHARPE 1430 UNIVERSAL OD / ID GRINDER,S/N 521-1430-148, 14” Swing x 30” Centers, MotorizedWorkhead, Universal Wheelhead, Coolant

1 – CINCINNATI R-55 HYDRAULIC OD CYLINDRICALGRINDER, S/N 26917, 10” x 12”, Universal Wheelhead,Motorized Workhead, Coolant

1 – BROWN & SHARPE NO. 13 UNIVERSAL TOOL & GRINDING MACHINE, S/N 525-13-742, Readout, Coolant

1 – PRODUCTO F-4 ROTO RECIPRO TOOLMAKERS ID GRINDER,Reciprocating Vertical ID Spindle, Precise ID Spindle WithVariable Speed Control, Variable Strokes Per Minute to 350 Max.

center Hole GrinDer1 – BRYANT CENTER HOLE GRINDING MACHINE, S/N C-1513

coorDinate MeaSurinG MacHineS1 – BROWN & SHARPE ONE 7.7.5 BRIDGE TYPE

COORDINATE MEASURING MACHINE, S/N 0208-7008(2008), 3-1/2” x 37” Granite Surface Plate, Renishaw PH10MProbe Head, Operator’s Joystick Pendant, PC DMIS 4.3Software, Missing Control Computer

1 – BROWN & SHARPE – OOG CHAMELEON 7107 SPZCOORDINATE MEASURING MACHINE, S/N 0499-2318(1999), Granite Table Size 40” x 65”, Renishaw PH10MQProbe Head, Renishaw SCR200 6-Station Linear Probe,Changeover Holder, Operator’s Joystick Pendant, PC DMIS3.8 Software, Operating PC

tool PreSetterS1 – PARLEC SERIES 2000 PRESETTER OPTICAL TOOL

PRESETTER, S/N 229990-0800

1 – MTS 273-EA7 OPTICAL TOOL PRESETTER, S/N 2747

inSPection1 – SCHERR TUMICO 22-2500 30” OPTICAL COMPARATOR,

S/N 837, Quadra-Chek 200 Programmable Terminal

1 – SIGMA HB-400 15” BENCH TOP OPTICAL COMPARATOR,S/N 3301/5/90, Quadra-Chek 2000 Programmable Terminal

1 – BROWN & SHARPE MICRO HITE 24” PROGRAMMABLEHEIGHT GAUGE

1 – STARRETT 48” X 72” X 10” 2-LEDGE PINK GRANITESURFACE PLATE

toolrooM MiScellaneouS MacHineS1 – SUNNEN MBB-1660 PRECISION HONE, S/N NA

1 – FARREL SELLERS 6GA DRILL POINT GRINDER, S/N 61R2306, Coolant

1 – COOLEY TYPE BL-121218 BOX TYPE ELECTRIC TOOLROOM HEAT TREAT FURNACE, S/N A-1216,Maximum Temperature 2000 Degrees Fahrenheit, Honeywell Digital Temperature Control

1 – BURR KING 760 2” ABRASIVE BELT GRINDER, S/N NA, With Portable Dust Collector Base

1 – GARDNER 3DB DOUBLE END BUFFING / POLISHING MACHINE, S/N 3DB 244D

1 – PRATT & WHITNEY 12-B 12” VERTICAL SHAPER, S/N 5400

1 – T.M.I. NA CENTRAL DUST COLLECTOR, S/N NA, Dry Type, Floor Standing

1 – EVERETT 20DM22 20” ABRASIVE CUT-OFF SAW, S/N 04-10149, 20-HP, 20” Blade, Pneumatic PowerClamping, Manual Feed, Dust Collector Blower

1 – ECONOLINE 36” X 24” ABRASIVE BLAST CABINET, S/N NA, With Dust Collector

1 – SETCO TYPE 102-202-8 SPL HEAVY DUTY 12” X 1-1/2” 2-HP DOUBLE END GRINDER, S/N 112354

1 – SETCO TYPE 402-303-8 SPL 18” DOUBLE-END FACE GRINDER, S/N 112389, 3-HP

Power SQuarinG SHearS1 – PROMECAM GH 1230A 10’ X 9/16” HYDRAULIC POWER SQUARING SHEAR, S/N NA, (3) Scale /

Capacity Settings: 48,000 PSI – 20 Gauge to 9/16”, 64,000 PSI – 20 Gauge to 1/2”, 85,000 PSI – 20 Gaugeto 5/16”, Front Operated Power Back Gauge, 24” Throat

1 – HTC 250-10A 1/4” X 10’ HYDRAULIC POWER SQUARING SHEAR, S/N A573661, Front OperatedPower Back Gauge

BenDinG BraKeS1 – HTC 200-12H 200-TON X 12’ HYDRAULIC PRESS BRAKE, S/N 580G2010, 24” Front Operated Power

Back Gauge, 126” Between Housings

1 – DRIES & KRUMP CHICAGO PB-10135 10’ POWER LEAF BENDING BRAKE, S/N 120123

BenDinG rollS1 – BUFFALO 2UBR VERTICAL ANGLE BENDING ROLLS, S/N 69U6816, Hydraulic Roll Adjustment,

Cleveland Size 70AF Series 25, 19:1 Ratio Mechanical Drive Gearbox

1 – 48” INITIAL TYPE POWER BENDING ROLLS, S/N NA, 6” Roll Diameter

baLer • autO LIFts • CnC prOduCtIOn bOrIng & turnIng maCHInes

to schedule an auction, please call Hilco Industrial, LLC at 1-877-37-HILCO (44526)6

HYDraulic SHoP PreSSeS1 – H-FRAME HYDRAULIC INDUSTRIAL TIRE PRESS, Estimated

250-Ton, Bed Size 48” x 48”, 15-HP Hydraulic Power Unit

1 – OTC 150-TON ROLL-BED H-FRAME HYDRAULIC SHOP PRESS,S/N NA, Extended Vertical Frame, 60” Maximum Height UnderAdjustable Top Rail, Roll-Out Bottom Bed Rail, Electric HydraulicPower Unit

1 – 2-POST HYDRAULIC PRESS, Estimated 100-Ton

HYDraulic Baler1 – PIQUA SERIES 40 VERTICAL HYDRAULIC BALER, S/N NA,

Chamber Size 36” x 60”, Floor Standing, Top Mounted Hydraulics

autoMotiVe liFtS1 – MOHAWK SYSTEM I-A 9000-LB. CAPACITY 2-POST

AUTOMOTIVE SERVICE LIFT, S/N 9505637, Floor Standing, 2-HP 3-Phase Hydraulic Unit

1 – MOHAWK A-7 7000-LB. CAPACITY 2-POST AUTOMOTIVE SERVICE LIFT, S/N 9303430, Floor Standing, 2-HP 3-PhaseHydraulic Unit

(22) cnc ProDuction BorinG / turninG MacHineS14 – SAGINAW MACHINE SYSTEMS ACCU-CELL 450-2S 2-SPINDLE

VERTICAL CNC PRODUCTION BORING / TURNING MACHINES,(5) S/Ns 50118-3/90, 50117-3/90, 50089-07/89, 50088-07/89, 50079-07/89 With GE Fanuc Series 15-T Operator’s CNC PendantBox Control, (2) 15” Vertical Power Workpiece Chucking Spindles,Manual Load / Unload, (2) 30/37 KW Spindle Drive Motors,Connected Into Central Supplied Coolant System, Magnetic ChipConveyor, (7) S/Ns 50095-07/89, NA, NA, 50078-07/89, 2677-11/86,2674-10/86, 50094-07/89 With General Numeric / Fanuc GN-11Series Control,(2) 15” Vertical Power Workpiece Chucking Spindles,Manual Load / Unload, (2) 30/37 KW Spindle Drive Motors,Connected Into Central Supplied Coolant System, (2) S/Ns50161/50119-11/90 & 50162-10/91 With General Numeric GN15Series Pendant Box CNC Control, (2) 14” Vertical Power ChuckingSpindles Each With 30/37 KW Spindle Drive Motors, Metal Belt DCMotorized Chip Conveyor, All With R&L Side Overhead Tool Slides,Power Enclosure Doors, Hinged Main PLC Control Panel, HydraulicPower Unit, *Note: Some Machines May Be Incomplete

8 – OLOFSSON 1075T-14LH, 1075T-14RH, 1075T-14-RH, 1075T-14LH,SPECIAL, SPECIAL, 1075T-14LH, 1075T-14RH CNC SINGLE SPINDLE VERTICAL PRODUCTION TURNING MACHINES, S/N 13809, 13807, 13808, 13806, 13803, 13805, 13802, 13804, GEFanuc Series 15T Control, 15” Diameter Vertical Spindle Chuck,Overhead 2-Axis Tool Spindle, 11/15KW Spindle Drive

(26) ProDuction BorinG / turninG MacHineS4 – SAGINAW MACHINE & TOOL VC-300-2 2-SPINDLE VERTICAL AUTOMATIC PRODUCTION

BORING / TURNING MACHINES, S/N 1805-0680, 1806-0680, 1961-0981, 1814-1080, (2) 10”Vertical Spindle Power Collet Closer Chucks, Single 25-HP Spindle Drive Motor, Gang TypeOverhead Tool Slide, Auto Load / Unload With Slide Type Transfer, Checking Stand WithSamsomatic Programmable In-Process Gaging, Main PLC Control Panel, Operator’s Push-ButtonStation, Machine #2-Auto, 1-Auto, 4-Auto, 3-Auto

8 – SAGINAW MACHINE & TOOL V3-300-2A 2-SPINDLE VERTICAL PRODUCTION BORING /TURNING MACHINES, S/N 1956-0581, 1955-0681, 1813-0680, 1824-0680, 1807-1080, 1812-1080,1811-1080, 1823-0680, (2) Vertical Spindle With 14” Power Collet Hub Chucks, Independent 10-HPSpindle Drive Motors, Gang Type Overhead Tool Slide, Manual Load / Unload, Main PLC ControlPanel, Operator’s Push-Button Station, Machine #1-Man., 2-Man., 3-Man., 4-Man., 5-Man., 6-Man.,7-Man., 8-Man.

4 – OLOFSSON 44-C 2-SPINDLE VERTICAL AUTOMATIC PRODUCTION BORING / TURNINGMACHINES, S/N 12699, 12698, 12775, 12774, (2) 8” Vertical Spindle Power Clamping WorkChucks, Overhead Gang Type Tool Slide, Single 15-HP Spindle Drive Motor, Manual Load / Unload,Main PLC Control Panel, Operator’s Push-Button Panel, Machine #3, 4, 6, 5

1 – WERTH NA 3-SPINDLE VERTICAL PRODUCTION BORING / TURNING MACHINE, S/N NA, (3) Vertical Spindles With Power Collet Chucks, 10-HP Spindle Drive Motors, Gang Type OverheadTool Slide, Manual Load / Unload, Main PLC Control Panel, Operator’s Push-Button Station,MayFran AC Motorized Chip Conveyor

7 – WERTH 55H-3-AL 3-SPINDLE SLANT BED PRODUCTION BORING / TURNING MACHINES, S/N 4266-1080, 4204, 3949, 4202, 4264-1080, 4694-0882, 4696-0783, (3) Power Collet ChuckingSpindles With Individual 20-HP Spindle Drive Motors, Slant Bed Gang Type Tool Slide, Auto Load /Unload With 2-Position Turret Type Loader, Main PLC Control Panel, Operator’s Station, Machine#1, 2, 3, 7, 8, 9, 10, *Note: Some Machines May Be Incomplete

2 – NEW BRITAIN 66 2-SPINDLE VERTICAL CHUCKING / TURNING MACHINES, S/Ns 37913, 5846-0785, (2) 18” Vertical Power Chucking Spindles, R&L Single Station Overhead Tool Spindles,(2) 10-HP Spindle Drive Motors, PLC Panel, Operator’s Push-Button Station, (S/N 5846-0785:Werth Re-Build)

tab rOLLers • vane assembLy & deteCtIOn maCHInes

For more information, please visit us on the web at www.hilcoind.com 7

(21) ProDuction DrillinG/BorinG MacHineS8 – L & L MACHINE TOOL SINGLE HEAD MULTIPLE

SPINDLE VERTICAL PRODUCTION DRILLING / BORING MACHINES, Sliding Head, Box Column,Manual Load / Unload, Power Workpiece Clamping,Auto-Cycle, Main PLC Control Panel, Operator’s Push-Button Control Station With Status Lights

6 – L & L MACHINE TOOL SINGLE HEAD MULTIPLESPINDLE VERTICAL PRODUCTION DRILLINGMACHINES, Sliding Head, Box Column, AEG ModiconPanel Mate Plus PLC Operator’s Terminal, Main PLCPanel, (4) With Manual Load / Unload, IndependentPortable Coolant System With Magnetic ChipConveyor, (2) With Auto Clamping Fixture Table, AutoCycle, Livonia Magnetics Magnetic Chip Conveyor

4 – L & L MACHINE TOOL SINGLE HEAD HORIZONTALPRODUCTION PILOT HOLE DRILLS, Auto Thru-Feed, Main PLC Panel, Operator’s Station

1 – L & L MACHINE TOOL SINGLE SPINDLE HORIZONTAL PRODUCTION DRILLING / BORINGMACHINE, AEG Modicon Panel Mate Plus PLCOperator’s Terminal, PLC Panel

2 – L & L MACHINE TOOL CUSTOM TORQUE CONVERTER HUB PILOT DRILL MACHINES,Horizontal Single Head, Chip Conveyor, Modicon PanelMate Plus PLC Operator’s Terminal Main PLC Panel

(53) HYDraulic PiercinG / StaKinG / inDentinG MacHineS39 – KOPPY 4-POST HYDRAULIC SPECIAL TOOL INDENT

/ PIERCE / STAKE MACHINES, All With Self-ContainedHydraulic Power Unit, Main PLC Control Panel, (16) WithModicon Panel Mate Plus PLC Pendant Terminal, (2) WithOperator’s Push-Button Control Station, With ModiconPanel Mate Plus PLC Operator’s Terminal, (21) WithOperator’s Push-Button Control Station

14 – KOPPY 4-POST HYDRAULIC SPECIAL TOOLPIERCE MACHINES, All With Self-ContainedHydraulic Unit, Main PLC Control Panel, Operator’sStation, (7) With Type 245 Pump Inner Piercer Op 25,(7) With Type Turbines, Op 20 Inner

(19) taB roller MacHineS8 – SPEN TECH OP. 40 TAB ROLLER MACHINES, Main PLC Control Panel, Vertical Slide Single Spindle, 3-Station

Index Table, Auto Unloader, Operator’s Panel With Push-Button & Status Lights

1 – SPEN TECH 2-SPINDLE VERTICAL TAB ROLLER, Independent Vertical Spindles With Slide Base Head & ACSpindle Motor, 3-Station Index Table With Auto Load / Unload, 15-HP Hydraulic Power Unit, Steel Skid Base, MainPLC Control Panel, Modicon Panel Mate Plus Operator’s Terminal

4 – STANDARD TOOL 2-SPINDLE VERTICAL TAB ROLLERS, Independent Spindle Heads With Vertical Slide &AC Motor, Hydraulic Power Unit, Main PLC Control Panel, Operator’s Station Panel

5 – STANDARD TOOL 2-SPINDLE VERTICAL TAB ROLLERS, Independent Vertical Spindles With Head Slide &AC Motor Drive, Auto Transfer, Main PLC Panel, Operator’s Station

1 – BROTHERS INDUSTRIES 2-SPINDLE VERTICAL TAB ROLLER, OP. 30 265 Turbine Tab Roll, Hydraulic UnitWith (3) 10-HP Pumps

turBine Vane aSSeMBlY MacHineS & Vane DetectorS8 – UTICA ASSEMBLY SYSTEMS NO. 4 TURBINE VANE SETTER ASSEMBLY MACHINES, Main PLC Control

Panel, Operator’s Panel With Push-Button & Status Light

5 – GIDDINGS & LEWIS GILMAN VANE SETTER ASSEMBLY MACHINES, S/Ns 692-140, 692-109, 692-131,381547, 692-119, Main PLC Panel With Operator’s Push-Button Station

8 – GIDDINGS & LEWIS GILMAN TURBINE OP. 60 MACHINES, S/Ns 629-149, -151, -115, -118, -144, -143, -148,-116, Main PLC Panel With Operator’s Push-Button Station

4 – VANE DETECTORS, PLC Control Panel, Thru-Feed Conveyor

1 – UTICA ASSEMBLY SYSTEMS 265 TURBINE VANE ASSEMBLY MACHINE

1 – #3 TURBINE STAKER PRESS, Single Vertical Hydraulic Ram, 6-Station Index Table, Main PLC Panel,Operator’s Panel

(28) autoMateD aSSeMBlY & SeconDarY MacHineS2 – ORBITAL RIVET AUTOMATED ASSEMBLY MACHINES, OP. 70, 4-Station Index Table, Auto Parts Feed /

Pick-N-Place, Single Orbit Form Orbital Riveter, AEG Modicon Panel Mate Plus PLC Operator’s Terminal, MainPLC Panel, Interfaced Enclosure

2 – WRIGHT-K TECHNOLOGY STATOR TORQUE CONVERTER OP. 130 & 80 SPRING & RUBBER ASSEMBLYMACHINES, Main PLC Control Panel, Vibratory Feeder Hopper / Bowl

1 – STATOR TORQUE CONVERTER OP. 100 SPRING & RUBBER ASSEMBLY MACHINE, Main PLC ControlPanel, Vibratory Feeder Hopper / Bowl

1 – SPEN TECH STATOR TORQUE CONVERTER SNAP RING ASSEMBLY & FUNCTION TEST MACHINE, Main PLC Control Panel, Panel Mate PLC Operator’s Terminal

3 – WELDUN OP. 50 STATOR SPRING & ROLLER ASSEMBLY MACHINES, Auto Feed & Transfer, In-Line, 8-Station, (4) Vibratory Hoppers / Bowl Feeders, Main PLC Control Panel, Operator’s Station With Push-ButtonControl Panel & Status Lights

4 – STATOR CAM PRESSES, Automatic Feed & Transfer, Main Control Panel With Gould Modicon 484 PLC,Operator’s Station With Push Button Panel & Status Lights

2 – NEW TECHNOLOGIES INC NORTH O-RING ASSEMBLY / LEAK TEST LINES, Automatic, Main PLC ControlPanel / Operator’s Station

1 – UTICA ASSEMBLY SYSTEMS 265 TURBINE OP. 50 VANE ASSEMBLY MACHINE

6 – HELFRECHT MACHINE CO OIL FILL & TEST MACHINES, S/Ns 806452, 806431, 806429, (3) NA, AutomatedTransfer, 30-HP Hydraulic Unit, Main PLC Panel, Operator’s Station With PLC Touch Screen & Push-Button Panel

6 – R&B MACHINE TOOL LUG MILL OP. 60 MACHINING STATIONS, S/Ns 6792-01, 6688-01, 6631-01, 6634-01,6631-01, N/A, Common Base With (1) Vertical Column Single Head Multi-Spindle Drilling / Chamfering Head, (1) Vertical Column Single Head Multi-Spindle Milling Head, Automatic Part Transfer, Main PLC Panel, Operator’sControl Station

A buyers premium will be in effect for all onsite and webcast sales.

baLanCers • burnIsHIng, brOaCHIng & pOLIsHIng maCHInes

to schedule an auction, please call Hilco Industrial, LLC at 1-877-37-HILCO (44526)8

(12) autoMatic inSertion / aSSeMBlY PreSSeS5 – NOVI PRECISION / GREENERD AUTOMATIC HYDRAULIC BUSHING ASSEMBLY PRESSES,

Greenerd Model HBB-10, 10-Ton C-Frame Hydraulic Presses, S/Ns 94T4901, 96T5199, 96T5126,96T5160, 94T4888 (To 1996), Novi Precision Automation, Main Control Panel With AEG PLC, AEGModicon Panel Mate Plus PLC Operator’s Terminal

3 – WRIGHT-K TECHNOLOGY SPECIAL BUILT AUTOMATIC INSERTION PRESS, 6-Station WorkpieceIndex Table, Auto Load / Unload, Parts Feeder, Main PLC Control Panel, AEG Modicon Panel Mate PlusPLC Operator’s Terminal, *Note: Some Machines Incomplete

1 – BAY CITY BORING AUTOMATIC BUSHING ASSEMBLY PRESS MACHINES, S/N 7901, 7902, 8002,8001, Automatic Parts Feed, Main PLC Control Panel, Operator’s Station With Push-Button & StatusLight Panel

2 – SPEN TECH OP. 40 CAM PRESSES, C-Frame Hydraulic Press Frame, Main PLC Control Panel,Tonnage Load Cell Monitor with Promess Programmable Controller

1 – NEW TECHNOLOGIES INC COVER HYDRAULIC ASSEMBLY PRESS, 6-Station Index Table, Main PLC Panel, Operator’s Station

(6) BurniSHinG MacHineS5 – SPECIAL MACHINE & ENGINEERING 265 TORQUE CONVERTER 3-SPINDLE VERTICAL

ASSEMBLY BURNISHING MACHINES, Automatic Part Transfer, Gage-Chek Programmable In-Process Checking, Main PLC Panel, Operator’s Station With Push-Button Control Panel & Status Lights

1 – AGNEW SINGLE RAM VERTICAL 265 COVER BURNISHING MACHINE, Quill Advance Spindle,Manual Load / Unload, Coolant, Hydraulic Unit, PLC Panel, Operator’s Station

(3) BroacHinG MacHineS1 – DETROIT BROACH VERTICAL TABLE UP HYDRAULIC BROACHING MACHINE,

S/N M-935018 (1994)

1 – AMERICAN BROACH & MACHINE CO V-2-6 6-TON VERTICAL HYDRAULIC BROACHINGMACHINE, S/N 6248, Single Ram, 24” Stroke, Hydraulic Power Unit

1 – AMERICAN BROACH & MACHINE CO 4HT 4-TON VERTICAL HYDRAULIC BROACHINGMACHINE, S/N 6822, Single Ram, Approx. 16” Stroke, External 5-HP Hydraulic Power Unit

(4) PoliSHinG MacHineS3 – HEGENSCHEIDT MFD 2-STATION TORQUE CONVERTER POLISHING MACHINES, Automatic

Thru-Feed Transfer, R&L Polishing Heads, Main PLC Control Panel, AEG Modicon Panel Mate PlusPLC Operator’s Terminal, *Note: Some Machines Incomplete

1 – NAGEL 2-SPINDLE VERTICAL MICRO-POLISHER MACHINE, S/N NA, 265 Converter OP. 90, (2) 14” Diameter Vertical Work Spindle Chucks, R&L Overhead Strip Polishing Heads, Main PLCControl Panel, AEG Modicon Panel Mate Plus PLC Operator’s Terminal, Hoffman Coolant Filtration &Recirculation Unit

(27) BalancerS3 – BALANCE ENGINEERING STATOR BALANCERS, S/Ns 2821,

2757, 2756, Auto Part Load & Transfer, (6) IndependentHorizontal Drill Spindle Units, CBI-55 Data Collector Terminal,Main PLC Control Panel, Operator’s Push-Button Station WithStatus Lights

3 – BALANCE ENGINEERING OP. 50 STATOR BALANCERS,S/Ns 3375, 3374, 3519, (5) Independent Horizontal Drill SpindleUnits, Auto Load / Transfer, Single Workpiece Spin / BalanceSpindle, CBI-55 Data Processing Monitor, Main PLC ControlPanel, Operator’s Push-Button Panel

4 – BALANCE ENGINEERING TURBINE AUTO-BALANCERS,S/Ns 2776, 2775, 2830, 2777, Type STMS-45, Weld Type, 5-Station, Auto Load & Transfer, Main PLC Control Panel,Operator’s Control Console With Push-Buttons, Status Lights, &CB1-58 Data Processing Terminal

1 – BALANCE ENGINEERING 254 TURBINE REPAIR BALANCER, S/N 2825, Weld Type, Strip Feeder, Medar WeldControls, Rotary Workpiece Fixture, Manual Load, CBI-55 DataProcessing Terminal, Main PLC Control Panel

1 – BALANCE ENGINEERING 265 TURBINE / CLUTCH BALANCER, S/N 3123, Drill Type, (3) Independent HorizontalDrill Spindle Units, Auto Load / Transfer, Main PLC ControlPanel, Operator’s Station, CBI-55 Data Processing Terminal

2 – BALANCE ENGINEERING 265 TURBINE OP. 90 BALANCERS, S/Ns 2718, 2633, Type STR-193, Weld Type,Speed Stop Feed, Medar Medweld 700S Weld Controls, RotaryFixture Table, Main PLC Control Panel, Operator’s Push-ButtonStation, CBI-55 Data Processing Terminal

6 – BALANCE ENGINEERING 265 CONVERTER AUTO-BALANCERS, S/Ns 2835, 2834, 2727, 2728, 2729, 2832, OP.80, Spot Weld Type, 2-Spindle, Automatic Feed & Transfer, MainPLC Panel, Operator’s Console Control With Push-Buttons,Status Lights & Data Processing Terminal

2 – BALANCE ENGINEERING 265 TORQUE CONVERTER BALANCERS, Weld Type With Medar Meldweld 700S Weld Control,Data Processing Terminal, PLC Panel, Operator’s Station

4 – BALANCE ENGINEERING OP. 100 AUTOMATIC TURBINEBALANCERS, S/Ns 3372, 3371, 3373, 3370, Weld Type WithMedar Medweld 700S Weld Controller Steel Strip Feed, PLCControl Panel, Operator’s Push-Button Station, Data ProcessingTerminal, Hydraulic Power Unit

1 – BALANCE ENGINEERING CONVERTER BALANCER, S/N2738, Weld Type With Medar MIZ’R Weld Control, Manual Load,PLC Control Panel

For more information, please visit us on the web at www.hilcoind.com 9

gagIng & CHeCKIng maCHInes • WeLders & equIpment

(12) autoMatic GaGinG & cHecKinG MacHineS4 – AIR GAGE COMPANY COMPUTERIZED IN-PROCESS PISTON GAGING

MACHINES, Automatic, Dearborn Precision Gage Operator’s PendantControl Terminal, Eaton Panel Mate PLC Console Control, (2) Gage CompTemperature Compensating Measurement Gages

2 – AUTO LOGIC AUTOMATED VISION & INSERT PROBE INSPECTIONMACHINES, Main Control Panel With AEG Modicon 878 PLC & PC SystemControl, Automated Workstation, Nemation PLC Monitor

2 – STRATORS OP. 60, EAST & WEST VISION SYSTEMS, (5) Regulated FeedTrack Conveyor Lanes, PC Control Cabinet

1 – B&K MACHINE AUTOMATED TORQUE RUN-DOWN MACHINE, AutomaticIn-Line Transfer, Main PLC Panel With Operator’s Touch Screen, Operator’sStation With Push-Button Controls & Status Lights

1 – NEW TECHNOLOGIES INC 265 TURBINE / CLUTCH O-RING LEAK TESTMACHINE, Automatic, AEG Modicon PLC

1 – PICO DYNAMIC TEST MACHINE, Horizontal Double-End Opposed Heads,60-HP AC Drives With UNICO Drive, AEG Modicon Factory Mate Plus PLC Terminal

1 – NOVI PRECISION AUTOMATED LUG THREAD CHECKER

(10) electron BeaM welDerS5 – SCIAKY C.V. 2-S-1DF6 ELECTRON BEAM WELDERS, S/Ns 10731, 10806,

10732, 10743, N/A, Power Output: 60 KVA, 250 MA, 371 IH, 6-Station IndexWorktable, Power Supply, Overhead Slide Auto Load / Unload, Vacuum PumpUnits, Hydraulic Unit, Chiller, Main PLC Control Panel With Modicon PanelMate Plus Touch Screen Terminal, Operator’s Station, Welder #5

4 – LEYBOLD – HERAEUS NVW-(35) ELECTRON BEAM WELDERS, S/Ns 836, 838, (2) NA, Machine Output: 200 KV – 175 Milliamp, WorkstationWith 4-Station Index Table, Automatic Parts Handling, High-Voltage PowerSupply, AC Generator, Vacuum Pump Systems, Main PLC Control Panel WithOperator’s Panel, Operator’s Push-Button Station, DCE Dalamatic Dust / Mist Collector

1 – LEYBOLD-HERAEUS ELECTRON BEAM WELDER, S/N NA, 4-StationTorque Converter Index Table, Auto Parts Load / Handling, High-VoltagePower Supply, Vacuum Pump Systems With Aercology Mist Collector,Hydraulic Power Unit, Main PLC Control Panel With AEG Modicon PLC, AEGModicon Panel Mate Plus PLC Operator’s Terminal, Operator’s Station WithPush-Button Control Panel, DCE Vokes Dalamatic Dust / Mist Collector

MaSS SPectroMeterS4 – NEWCOR MASS SPECTROMETER / LEAK TEST MACHINES, S/Ns X9021,

9026, 9047, N/A, 4-Station Workpiece Index Table, Automatic Parts Handling,Vacuum Pump System, Data Processing Panel, Main PLC Control Panel,Operator’s Station, Hydraulic Power Unit,

1 – MASS SPECTROMETER, Vacuum System, 4-Station Workpiece Index Table,Automatic Parts Handling, Main PLC Control Panel, Data Processing Panel

welDinG eQuiPMent1 – HOBART MEGA-MIG 450 WELDING POWER SUPPLY, S/N 80WS 14915,

With Hobart 70L Wire Feeder

1 – MILLER SYNCRO WAVE 350 AC / DC WELDING POWER SUPPLY, S/N JK707977, With Coolmate 3 Water Cooler

1 – MILLER INVISION 456P DC INVERTER WELDING POWER SUPPLY, S/N NA, With 60 Series 24V Dual Wire Feeder

1 – MILLER DELTAWELD 452 CV-DC WELDING POWER SUPPLY, S/N LA091778, With Miller 60 Series 24V Cart Mounted Wire Feeder

1 – MILLER MAXTRON 300 CC-CV DC INVERTER WELDING POWER SUPPLY, S/N KA868590, With XR Extended Reach Wire Feeder,Millermatic S-525 Wire Feeder, Optima 300 GMAW Control

1 – THERMAL ARC PAR-TOR 10XR PLASMA CUTTER, S/N NA

1 – LINCOLN SQUARE WAVE TIG-350 SQUARE WAVE AC / DC TIG & STOCKARC WELDING POWER SUPPLY, S/N AC760200, Tig Leads

1 – LINCOLN IDEALARC TIG-300/300 AC / DC WELDING POWER SUPPLY,S/N AC-280230

(4) roBotic MiG welDinG cellS, eacH incluDinG:1 – FANUC ARC-MATE 100i 6-AXIS CNC ROBOT, S/N NA (1998-1999), With System

R-J3 Control

1 – LINCOLN POWERWAVE 450 WELDING POWER SUPPLY, With Robotic Interface

1 – GWI ENGINEERING WORK CELL, With 2-Station Workpiece Index Table, Manual Load,Interfaced Enclosure with Modicon Panel Mate Plus PLC Terminal

1 – TORIT DOWNFLO SDF6 DUST COLLECTOR, Checker Board Microprocessor Control

(2) roBotic MiG welDinG cell / 265 coVer aSSeMBlY nortH &SoutH, BotH incluDinG:1 – FANUC ARC-MATE 6-AXIS CNC ROBOT, S/Ns R93265999, R93265983 (1993),

Type A05B-1203-B275 System R-J Control With Hand Teach Pendant

1 – LINCOLN IDEALARC PULSE POWER 500 DC WELDING POWER SUPPLY, WireFeeder, NA-5R Interface Adapter

1 – GWI ENGINEERING WORK CELL, With 3-Station Workpiece Index Table, Auto-Load,Interfaced Enclosure With AEG Modicon Panel Mate Plus PLC Operator’s Terminal

1 – TORIT SDF6 DOWN FLO DUST COLLECTOR, Free Standing, 10-HP, (6) ReplaceableDry-Type Cartridge Filters, Torit Checker Board Microprocessor Control Panel

(13) Multi-Station welDinG MacHineS4 – BRA-CON SPECIAL BUILT MULTI-STATION AUTOMATIC THRU-FEED MIG WELDING

MACHINES, In-Line Automatic Parts Transfer, Transfer Line Drive, Main PLC ControlPanel, Operator’s Push-Button Control Station, (2) With Welding Equipment Including: (6)Thermal Arc / Hobart HMC-410 Wire Feeders, (6) Lincoln Tig Square-Wave Welding PowerSupplies, (4) Hobart Welding Power Supplies, (2) Thermal-Arc Arc- Welding PowerSupplies, or (6) Thermal Arc / Hobart HMC-410 Wire Feeders, (6) Thermal Arc PlasmaWelding Consoles, (6) Thermal Arc Plasma Welding Power Supplies, *Note: PowerSupplies & Wire Feeders May Be Offered Separately

4 – NEWCOR 3-STATION AUTOMATIC MIG WELDING MACHINES, 8-Station WorkpieceIndex Table, Auto Parts Load, Main PLC Control Panel, Operator’s Push-Button ControlStation, (2) With Welding Equipment Including: (3) Thermal Arc HMC-410 Wire Feeders,(2) Thermal Arc Arc-Master 501 Welding Power Supply’s, (1) Hobart Arc-Master 501Welding Power Supply, *Note: Welding Power Supplies May Be Offered Separately

4 – NEWCOR WELD ASSEMBLY MACHINES, Newcor TIG-TACK Loose Assembly WelderOP. 30, 6-Head, Newcor Special Welding Press Frame, (6) Lincoln Square Wave TIG-350Welding Power Supplies, S/Ns NA, Support Mezzanine Mounted, (1) Hydraulic Power Unit,Main PLC Control Panel, Operator’s Station, Auto Parts Feed & Transfer

1 – B&K MACHINE 265 CONVERTER WELDING MACHINE, Special Fabricated 4-Post Welding Frame, (4) Lincoln Square Wave TIG-350 Welding Power Supplies, S/NsNA, (2) Miller 330-ST Air Crafter Welding Power Supplies, S/Ns NA, Hydraulic Power Unit,Main PLC Control Panel, Operator’s Station With Push-Button Controls & Status Lights

inertia welDer1 – MANUFACTURING TECHNOLOGY 120 V INERTIA WELDER, S/N 12BVMF2966, Vertical,

External 60-HP Hydraulic Power Unit, Single Piece Workstation With Auto Load, Main PLCControl Panel, Operator’s Station

OIL mIst & dust COLLeCtOrs • parts & tHru-Feed WasHers

to schedule an auction, please call Hilco Industrial, LLC at 1-877-37-HILCO (44526)10

(23) oil MiSt & DuSt collectorS2 – MONROE ENVIRONMENTAL CORP STC-260 26000 CFM OIL MIST

COLLECTORS, S/Ns 00-3666-2, 00-3666-1, Floor Standing, 60-HP

1 – TORIT SDF 6 DOWN FLO DUST / OIL MIST COLLECTOR, S/N IG346385-001, Free Standing, 10-HP, (6) Replaceable Dry-TypeCartridge Filters, Torit Checker Board Microprocessor Control Panel

8 – TORIT DRY FLO DMC-D1 – OIL MIST COLLECTORS, 7.5-HP,Floor Standing, Control Panel With Photohelic Indicator Gauge

4 – TORIT DOWN FLO DF-T4-16 DUST COLLECTORS, PneumaticPulse-Jet Cleaning, (8) Dry Type Replaceable Cartridge Filters, 20-HP, Floor Standing, Control Panel With (2) Dwyer PhotohelicIndicator Gauges

4 – TFP ELIMINATOR OIL MIST COLLECTORS, S/N IDS-745B, IDS-745-C, IDS-745-A, IDS-745-D, With Industrial Drive Service Control Panel,(2) Magnehelic & (1) Photohelic Indicator Gauges, Wall Mounted

4 – AERCOLOGY NA OIL MIST COLLECTORS

(17) caBinet tYPe PartS waSHerS10 – RANSOHOFF CABINET TYPE PARTS WASHERS, Center Column

With Rotary Parts Hanger Rack, Process Steam Heat Supplied, 20-HP Wash Recirculation Pump, Filters, Floor Standing, Manual Load /Unload, Light Curtain, Blow-Off, Control Panel, (1) With PoweredRotary Work Table

1 – RANSOHOFF ROTARY HANGER CABINET WASHER, CenterColumn With Rotary Parts Hanger Rack, Process Steam HeatSupplied, 20-HP Wash Recirculation Pump, Filters, Floor Standing,Manual Load / Unload, Light Curtain, Blow-Off, Control Panel

5 – RANSOHOFF ROTARY PARTS WASHERS, Process Steam HeatSupplied, Center Column Cabinet Type Base With Rotary HangerRack, 20-HP Wash Recirculation Pump, Filters, Heat Exchanger,Blow-Off, Mist Collector, PLC Control Panel, Manual Load / Unload

1 – GRAPAR CORP U-FLOW SR. PARTS WASHER, Center ColumnWith 12” Wide Powered Rotary Table, Ambient Temperature, CentralWash Solution Supplied, Recirculation Pumps, Control Panel, Blow-Off, Mist Collector

(15) tHru-FeeD waSHerS4 – CONTINENTAL EQUIPMENT CORP THRU-FEED REVERSE OSMOSIS WASHERS, Ambient

Wash Temperature, 14” Wide Opening With Thru-Feed Plastic Mesh Conveyor Belt, 15’ Length, (2) 5-HP Wash-Rinse Pumps, Blow-Off, Control Panel

1 – FLUID ENGINEERING REVERSE OSMOSIS WATER TREATMENT SYSTEMS, 30” x 36” x 48”Stainless Steel Tank, 500-Gallon Poly Holding Tank, (2) Fiberglass Filter Tanks, Steel Skid Base

1 – CARDEN THRU-FEED WASHER, 96” Wide Overall Opening Width With (4) 4” Thru-Feed PlasticChain Conveyor Lanes, Process Supplied Steam Heat, 12’ Length, (2) Remote 15-HP Wash /Rinse Pumps, Blow-Off

6 – RANSOHOFF THRU-FEED WASHERS, S/N H0872, 84” Overall Opening Width With (4) 12” Thru-Feed Chain Conveyor Lanes, (1) Approx 40-HP & (1) Approx. 15-HP Wash Pumps, (1) Free-Standing High-Pressure Pump System, S/N H2730, Horse-Shoe Type Thru-Feed, 12” Wide RollerConveyor, Recirculation Pumps, S/N H0993, 120” Overall Opening Width With (5) Thru-FeedChain Conveyor Lanes, (1) 40-HP & (1) 20-HP Recirculation Pumps, S/N H1003, (1) Estimated25-HP & (1) Estimated 15-HP Wash / Rinse Pumps, (5) Thru-Feed Chain Conveyor Lanes, 84”Overall Opening Width, Above (4) With Process Steam Heat Supplied, 30’ Length, Blow-Off,Control Panel, (2) Incomplete

1 – NEW TECHNOLOGIES INC THRU-FEED WASHER, S/N NA, Single 2” Wide Conveyor Track, 4’ Length, Blow-Off, Pumps, PLC Control Panel, Operator’s Station

2 – INDUSTRIAL METAL FABRICATORS THRU-FEED WASHERS, Process Steam Heat Supplied,(1) With 84” Overall Opening Width With (4) 12” Thru-Feed Chain Conveyor Lanes, (2) 15-HPWash / Rinse Recirculation Pumps, 30’ Length, Blow-Off, Control Panel, (1) With 60” OverallOpening Width, (3) 14” Wide Thru-Feed Chain Conveyor Lanes, Recirculation Pumps Removed,

For more information, please visit us on the web at www.hilcoind.com 11

materIaL HandLIng • gear CHeCKIng Lab equIpment

Material HanDlinG1 – KENWAY AUTOMATED STORAGE & RETRIEVAL SYSTEM, 3 Rows Storage

Units (2) Single Sided, (1) Double Sided, Approx 22’ Height x 75’ Length,Overhead Retrieval Crane System

2 – PRAB ROBOT TYPE FA MATERIAL HANDLING & TRANSFER ROBOTS, S/NsV-2085, V-2086, 3-Axis, Horizontal Double End Cantilever Arm With GripperFixtures, Track Mounted Sliding Base, PLC Control Panel

1 – MT. CLEMENS CRANE CHIP BALER OVERHEAD CHARGING CRANE, 1-TonCapacity x 25’ Span, Bottom Running With (3) Support Rail Tracks, DemagElectric Cable Hoist, With Type CE-20 20” Electromagnetic Lifting Magnet, RadioControlled With Remote Radio Operator’s Pedestal Control

2 – SPAN MASTER 5-TON CAPACITY BOTTOM RIDING SINGLE GIRDER BRIDGECRANES, 20’ Span, Acco-Wright Work-Rated 5-Ton Electric Cable Hoist, 6-WayPower Pendant Control, 2-Speed Hoist

3 – OMNI TECHNICAL SERVICE 5-POSITION GRAVITY OVER / UNDER PALLETEXCHANGE RACK, With Pneumatic Tilt Table, 2000-Lbs. Capacity Per Rack,Type 212X-45X48x25

1 – LANTECH LANWRAPPER SERIES SVGSU065017AA PALLET SHRINK WRAPMACHINE, 72” Table Diameter

FluiD HanDlinG1 – AQUANETICS INC MORS-150-T4E PORTABLE ON-SITE FLUID

RECLAMATION SYSTEM, S/N T-1207, AC Electric Vacuum Pump

3 – AUTO-TRACK SYSTEMS MAG-VAC INDUSTRIAL VACUUM UNITS, S/N NA

SHoP & FactorYLARGE QUANTITY SHOP & FACTORY EQUIPMENT, Plant Support, ProductionProcess Equipment, Production Control, etc.

Gear cHecKinG laB2 – ADCOLE 911 – COMPUTERIZED GEAR CHECKERS, With PCs

2 – ZEISS CONTOURECORD 1700 SD & 1600 D SURFACE CHECKERS, With PC

3 – TAYLOR HOBSON TALYROND 262 ROUNDNESS TESTERS, (2) With Table & PC

1 – HOMMELWERKE SURFACE CHECKER, With Granite Table & PC

1 – DORSEY BENCHMARK 16H OPTICAL COMPARATOR

(7) coolant Filtration & recirculation SYSteMS2 – HENRY FILTERS 3500 GPM SUMP WITH PRIMARY PROCESS COOLANT

FILTRATION & RECIRCULATION SYSTEM, S/Ns 6466, 6467 (2003), In-Ground,

36” Wide Tank With Chain Drive Drag-Out Conveyor & Above Ground Discharge,

(3) 40-HP Gormann Rupp Recirculation Pumps, Control Panel, With Dista View

LiquaVision Liquid Controller

1 – HENRY FILTERS 2-2.5-10 CF. 900 MV-136 PROCESS COOLANT FILTRATION &

RECIRCULATION SYSTEM, S/N 6465, Floor Standing, 8’ Wide Tank, Chain Drive

Drag-Out Conveyor With Screw Auger Side Discharge, Paper Media Filter, Model 3000

SID 2-2.5-10 CF & 900 MV-136 Super Vac Control Panel, S/N 5912, Schematic Flow

Chart With Operator’s Push-Button & Status Lights, LiquaVision Liquid Controller,

(2) 50-HP & (3) Est. 75-HP Recirculation Pumps

4 – ADVANCED FILTRATION CONCEPTS FSC-5-010 COOLANT FILTRATION &

RECIRCULATION UNITS, S/Ns AF-1381, AF-1378, AF-1380, NA (All 1994), Services

(2) Oloffson 1075T-14 CNC Turning Machines, Screw Conveyor Chip Extraction,

Settling Tank With Skimmer, 3-HP Recirculation Pump, PLC Control Panel

cHiP BalinG SYSteM1 – FRONTIER HYDRAULICS NA 2-RAM HORIZONTAL HYDRAULIC CHIP BALER,

S/N NA, Hydraulic Power Unit With (2) 75-HP Hydraulic Pumps, Bale Size Approx. 24”

x 18” x Variable, Compression Chamber Size 9’ x 54” x 24” High, Overall Charging

Hopper Size 9’ x 54” x 5’ High, Hydraulic Chamber Lid, Bale Exit Conveyor System

With Push-Off Stand, Run-Out Table & Carrier, 78” x 30’ Long Oscillating Shaker Table,

Main Control Panel With Allen Bradley PLC Control

Headquarters31555 W. Fourteen Mile Road, Suite 207Farmington Hills, MI 48334Ph: 877-37-HILCO (44526)Fx: 248.254.9995

www.hilcoind.com

Forwarding Service Requested

PresortedFirst Class MailU.S. Postage

PAIDDetroit, Mich.

Permit No. 100

Hilco Industrial, LLCA u c t i o n e e r s • L i q u i d a t o r s • A p p r a i s e r s

HILCO Industrial, LLC is a division of Hilco trading, LLC • Headquarters, 5 revere drive, ste. 206 • northbrook, IL 60062 • all rights reserved

printed in usa • mOtO3499 • IL License #444000215 • please visit our website at www.hilcoind.com to review our complete terms and conditions.

Atlanta • Birmingham • Birmingham (UK) • Boston • Charlotte • Chicago • Dallas • Detroit • Grand Rapids • Guadalajara (MX) • Hong Kong • Irapuato (MX)

Leeds (UK) • London (UK) • Los Angeles • Mexico City (MX) • Monterrey (MX) • New York • Phoenix • San Francisco • Toronto • Villahermosa (MX)

Terms of Salea buyer’s premium of 13.5% for onsite sales &  16% for webcast sales is in effect. everything will be sold tothe highest bidder for cash, in accordance with theauctioneer’s customary “Terms of Sale”, copies of whichwill be posted on the premises of the sale and subject toadditional terms announced the day of sale. all items willbe sold “as is, where-is” without any warranties, expressor implied. although obtained from sources deemed reliable, the auctioneer makes no warranty or guaranteeto the accuracy of the information herein contained.bidders are encouraged to thoroughly inspect the itemson which they intend to bid prior to sale. absolutely noitems will be removed until the day after the conclusion ofthe sale and payment is made in full. Subject to additions,deletions and prior sale.

Payment: all  purChaSeS  muST  be  paid  in  fullon  The  day  of  The  auCTion. if you intend to pay bywire transfer, we will accept payment the day after thesale only  if  a deposit of 25% of total purchases is madeon the day of the sale. Contact our office for wire transferinstructions. only cash, wire transfer or certified check,payable to maynards industries will be accepted.Company checks payable to maynards industries will beaccepted only if accompanied by a bank letter of guarantee, (see sample letter below). all sales are subjectto sales tax. purchasers claiming exemptions from taxesmust provide proof satisfactory to the auctioneer of theirentitlement to claim such exemptions.

Sample Bank Letter

(bank name) unconditionally guarantees paymentto maynards industries from (Company name). Thisguarantee will be valid for purchases made at theauction of motors liquidation Company flintpowertrain #2 on Tuesday, January 18, 2011.

HILCO WebCast/OnsIte auCtIOn

FollowUs on:

Flint Powertrain nortH #2