Controls electrostatic discharge

Abrasion and impact resistance

Resistant to most chemicals used in the electronics industry

Resistant to fire does not support combustion

Easy to clean

(ESD)

,

Multi-layer epoxy system, 100% solids.

Designed to meet the electrostatic conductive/dissipative requirements of a wide variety of industrial flooring needs.

Complementary Products

: Priostatic Primer

SYS

TEM

Priostatic Black Coat CN or DSPriostatic Top Coat

Ground connection

Substrate

Black Coat

Primer

Top Coat

PRIOSTATIC 80 STATIC PROTECTIVE SYSTEM(Formerly known as SPS)

Legend: E= Excellent G= Good F= Fair P= Poor

USES:

• Electronic Industries.

• Areas where a static protection is required.

Chemical Resistance

PRODUCT WARRANTY:

Pricoat products have a quality warranty that stipulates that its production and its raw material are free of defects with the commitment to credit the amount of the purchase or material recovery to the client in case of fault or defect. The material installer has to assume the installation warranty.

Colors

Physical Properties (Dry Film)

Medium Gray GraySoft GrayLight

Oyster White Ice BlueElectric Blue

Beige

.

• Colors are close approximations. For greater precision please contact a Pricoat representative for samples.•• White and Light Gray tend to turn yellow with the passage of time.

Day 1 Day 7

Property ResultsHardness, Shore D (ASTM D-2240) 50-80

Compressive strength (ASTM D-695) 6,000 psi

Tensile strength (ASTM F-638) 2,000 psi

Flexural strength (ASTM D-790) 2,350 psi

Ultimate elongation 3.5%

Coefficient of friction slip 0 .507

Inflammability (ASTM D-635) Self-extinguishing

Abrasion resistance, mg CS-17, 1000 ciclos, 1000 gr (ASTM D4060) 80Electrical surface resistance, 100V ESD STM 7.1-2001

Conductive:2.5x10 -1x10 ÙDissipative:1x10 -1x10 Ù

4 6

6 9

Application Characteristics

ThicknessMil

75

95

105

125

ft /gal.2

2.0

1.5

1.4

1.1

Coveragem /gal.

2

21

16

15

12

Packaging

Top Coat

Part B(Gal)

Kit (Gals.)

2 5

3

10

13

15

Part C(pounds)

Part A(Gal)

Black Coat Primer

1

10

0.5

65

5

5.5 11

1

3 15

1

4 20

5

N/A N/A N/A N/A

Pricoat Trademark in process.Presentation HPI0709-13

®

Note: Antistatic coatings have a tendency to attract the relative humidity, present in the air, to the polymer surface, improving its surface electrical conductivity. Is

5 6probably to obtain conductive measurements, from 10 to 10 , in systems 6 9formulated as electrostatic dissipative (10 – 10 ).

Ph. 52 (614) 481-4344 www.pricoat.cominfo@pricoat.com

Nicolás Gogol #11343 Complejo Industrial Chihuahua Chihuahua, Chih., Méx. ZC 31109

Inorganic Acids 10% Hydrochloric acid E E30% Hydrochloric acid E G10% Nitric acid E G50% Phosphoric acid F P37% Sulfuric acid G G

Organic acids 10% Acetic acid G F10% Acido cítrico G GOleic acid G F

Alkaline 10% Ammonium hydroxide E E50% Sodium hydroxide E E

Solvents (alcohols) Ethylene glycol antifreeze( ) E GIsopropyl alcohol F FMethanol F F

Solvents (aliphatic) d- Limonene G GJet JP 4 E EGasoline G GMineral spirits E E

Solvents (aromatics) Xylene F F

Solvents (chlorinated) Methylene chloride P P

Solvents (ketones & esters)

Methyl ethyl ketone (MEK) P PPropylene glicol methyl ether acetate (PMA) F F

Miscellaneous chemical

20% Ammonium nitrate E EBrake fluids F FBleach G GMotor oil (SAE30) E ESkydrol 500 B F FSkydrol Ld4 F F20% Sodium chloride E E1% Tide laundry soap E E10% Trisodium phosphate E E