Date post: | 03-Apr-2018 |
Category: |
Documents |
Upload: | lyle-hornbaker |
View: | 228 times |
Download: | 2 times |
of 17
7/29/2019 Horiz_Vert Router Table
1/17
Mission Furniture
Thank You!
Thank you or ordering thisWOOD magazine download. We hope youenjoy being part o our online experience and that you have un expand-
ing your woodworking skills.
Please remember that this copyrighted material is or your use only. It is
unlawul to share this fle with someone else or to reprint it in any orm.
Dave Campbell
Editorial Content Chie,WOODmagazine
Adobe Acrobat ReaderTroubleshooting Guide
I you can read this page, your Acrobat Reader program is working correctly!
But you may still have problems or specifc issues, such as printing and
saving your downloadable fle.
My printer wont print the text correctlyAlmost all printing problems are due to not enough ree system resourcesmemory. The fles are very memory intensive because they include graphics,
text, and photos. Close all other programs/applications and print directly out
o the Acrobat Reader program, not your Web browser.
Patterns are not printing ull-sizeMake sure your printer is set to print at 100 percent, print to ft is not
checked and page scaling is set to none. These settings are selected in
the printer setup or printer options.
I cant fnd my fle now that its downloadedRather than viewing the plan in your browser, you must save it to your hard
drive. Download the fle again, except this time try right-clicking on the red
download button. A menu window will open. Select Save target as or
Save link as to save the fle to your hard drive. Once saved, you can open it
up with Adobe Acrobat Reader.
For more details on using Adobe Acrobat Reader please
visit our online help section at:
woodmagazine.com/adobe
WOOD StoreCustomer Favorites
Visit the WOOD Store at:
WOODStore.net
Shop Tools & Accessories
Indoor Furniture
Outdoor Furniture
Browse more than 1,300 woodworking project plans, DVDs,
back-issue collections, videos, tool reviews, books, & more.
http://www.woodonline.com/http://woodstore.woodmall.com/clicherforde.html7/29/2019 Horiz_Vert Router Table
2/17
Note: To use the pivoting arm andcrank for raising and lowering therouter, you must install a plunge routerwhose motor housing top is flat andunobstructed.
Start with the cabinetand the tables
1Because you need the four studdedknobs already fabricated for use later
in the project, make them now. To makethe knobs, cut four 2fi" lengths of "threaded rod and epoxy them into fourplastic knobs. See the Buying Guide forour source for the knobs. Set the knobsaside while the epoxy cures.
2Cut the base (A) and sides (B) to thesizes listed in the Bill of Materials.
Drill four " holes in the base, whereshown on the Parts View drawing, at theend of this article. Cut the rabbets in thebottom edges of the sides, drill the "holes, and form the " slot, whereshown on the Parts View: Side drawing.The slot is located only on the right side.Glue and screw the sides to the base asshown in the Cabinet Assembly draw-ing, keeping the sides square to thebase.
3Cut the table front/back skirts (C),side skirts (D), auxiliary side skirts
(E), and auxiliary back skirt (F) to size.Form the rabbets in the ends of thefront/back skirts (C), rout the stoppedslots in the side skirts (D), and drill the" holes in the side skirts (D) and aux-
In its horizontal configuration, this routertable is great for mortise and tenon work. Acrank makes vertical adjustment con-
venient and accurate. For opera-tions requiring traditional vertical
orientation, the router table con-verts quickly without tools. The
same crank that adjusts the ver-tical table now raises and lowers
the plunge router.
all-purpose
54 DP-00364a WOOD magazine December2000
router stat ion
7/29/2019 Horiz_Vert Router Table
3/17
iliary side skirts (E), where shown on theTable Assembly, and Auxiliary TableAssembly drawings. To form thestopped slots in the side skirts (D), chucka " straight bit in your table-mountedrouter and raise it to cut " deep.Position the fence to center the bit on thewidth of the skirts. Limit the cut byclamping stopblocks to the fence. Withone end against the right stopblock,lower the skirt onto the running bit androut the length of the slot. Repeat thisprocess, raising the bit " with eachpass until you rout the slot through.Install the T-nuts in the side skirts (D) andauxiliary side skirts (E).
4Drill pilot and countersunk shankholes, and screw the frames together,
as shown on the Table Assembly andAuxiliary Table Assembly drawings.Cut the top (G) and auxiliary top (H) tosize, and clamp them to the frames C/Dand C/E/F, making certain the frames aresquare. Drill pilot and countersunkshank holes, where shown on the PartsView and Auxiliary Table Assemblydrawings, and screw and glue the tops tothe frames.
Note: The length of the table assem-blies C/D/G and C/E/F/H must be thesame dimension as the distance betweenthe cabinet sides (B), minus the thicknessof two business or playing cards foroperating clearance.
Doublemagneticcatch and strikeplates
#8 x 2fi" F.H.wood screws
x 2" carriage bolts formounting cabinet to stand
B
A
B 22"" holes
#8 x 2fi" F.H.wood screws
" slot" long
" holes,countersunkon back side
#8 x 1" F.H.wood screw
" rabbet fi" deep
1"
1"
3" wire pulls
1"
x 2"no-mortise
hinge
11"
" rabbet fi" deep
#8 x 1fi" F.H.wood screws
16"
12fi"
" hole
L
J
IJ
" hole
K
I
K
Mount router underneath plate.
11 x 10" Phenolic insert
" mini channel 11" long
#6 x 1" F.H. wood screw
#8 x 1fi" F.H. wood screws
Router plate cutout
" rabbet *" deep(*thickness of router plate)
" stopped rabbet" deep11" long
" groove " deep(Size to fit yourmiter gauge.)
Plastic knobs with" threaded inserts
" flat washers
" slot12" long
" hole,
countersunk
1" hole, countersunk
" hole
" T-nut x 2fi"hexhead bolt
" rabbet fi" deep
22"
24"
" threaded rod2fi" long,epoxied intoplastic knob
1" hole#10-24 x " F.H. machine screw
" hole, countersunk
" hole
#10-24 T-nut
G
D
" internal-tooth star lock washer
" flat washer
D
C
C
Continued
www.woodonline.com
1"
" slot " hole
" holes, countersunk(Angle holes 10.)
" 1"
2fi"
1"
12"
21fi"
fi"
fi"
fi"
D
Front end
1fi"
CABINET ASSEMBLY
TABLEASSEMBLY
SIDE
SKIRT
See theWOOD PATTERNS
insert for theFULL-SIZE PATTERNS and
Parts View drawing.
55
7/29/2019 Horiz_Vert Router Table
4/17
5Rout grooves in the top (G) and aux-iliary top (H) to match the bar on
your miter gauge, where shown on theParts View and Auxiliary TableAssembly drawings. Set the auxiliarytable aside. Rout the stopped rabbets inthe rear edges of the top (G), and squarethe ends with a chisel.
Form a recessfor the insert
1Trim the insert to size, and center iton the top (G), where shown on the
Parts View: Top drawing. Draw a pencil
line around it. See the Buying Guide forour source for an oversize insert blank.Remove the insert. Cut four 616"particleboard routing guides, and clamptwo of them in place aligned with twoadjacent sides of the marked outline.Replace the insert, and position andclamp the other two guides in place, asshown in Photo A. Remove the insert.
2Position " thick, " wide spacerstrips around the inside of the open-
ing formed by the routing guides. Secure"-thick, 45 triangles, 2" long on thediagonal, in the corners with double-
faced tape. Chuck a fi" top-bearingpattern bit in your handheld router.Starting with the depth of cut set at ",and increasing the depth of cut " witheach pass, make repeated passes to cut
56 WOOD magazine December 2000
x 48 x 96" Batlic birch plywood
RQ L
K
GBA HB
K
SPO
MMJ*
I *
J *
*These pieces are cut from the same blank.**Part initially cut oversize.
x 5 fi x 96" Maple
FED
C C D
U V
x 5 x 5" Tempered hardboardT
**
** **
I *
" plastic knobs withthreaded inserts
24"
" groove " deep, centered(Size to fit your miter gauge.)
" threaded rod 2fi" longepoxied into plastic knob
" flat washer
" holes,countersunkon back side
#8 x 1fi" F.H.wood screwsangled 10
" rabbetfi" deep
" hole
" T-nuts
1"
1"
13fi"
F
E
H
1"
E
2fi"
2"
" hole
#8 x 1fi" F.H. wood screw
" hole, countersunk
764" pilot hole " deep
C
Router Station
AUXILIARY TABLE ASSEMBLY
CUTTING DIAGRAM
* These pieces are cut from the same blank.** Part initially cut oversize.
Materials Key: BBBaltic birch plywood, Mmaple,Dhardwood dowel,Htempered hardboard.
Supplies: #61" flathead wood screws (15), #81"flathead wood screws (14), #81fi" flathead woodscrews (50), #82fi" flathead wood screws (5),2fi" hexhead bolts (2), 3" hexhead bolt, 4fi"hexhead bolt, 2" carriage bolts (4), #10-24" flat-head machine screws (4), " T-nuts (6), #10-24 T-nuts (4), " lock nuts (5), " hex nuts (4), " couplingnut, " flat washers (26), " nylon washer, " inter-nal-tooth star washers (2), 1" dowel (2" long), 2"no-mortise hinges (4), 3" wire pulls (2), double mag-netic catch, 1" wood knob, epoxy, clear finish,primer, paint.
Buying GuideHardware kit: " mini channel (2 @ 11", 1 @24" long), plastic knobs with " threaded inserts (11)," threaded rod (4 @ 2fi", 1 @ 9fi" long), 1fi"square-head bolts (5), 1111" phenolic sheet.Order WOOD KIT RTS-1, $47.95 ppd., Schlabaughand Sons Woodworking, 720 14th Street, Kalona, IA52247 or call 800/346-9663.Lumber pack: " Baltic birch plywood cut slightlylarger than the sizes listed on the Bill of Materials.Order WOOD KIT LP-3, $95.00 ppd. from the sameaddress or phone listed above.
finished sizePart T W L Matl. Qty.
A base " 22" 25" BB 1
B sides " 22" 16" BB 2
C front/back skirts " 2fi" 24" M 3
D side skirts " 2fi" 21fi" M 2E auxi liary
side skirts " 2fi" 13" M 2F auxi liary
back skirt " 2fi" 22fi" M 1
G top " 22" 24" BB 1
H auxiliary top " 13fi" 24" BB 1
I* brace " 4fi" 12" BB 2
J* table guide " 12" 12" BB 2
K doors " 11" 12fi" BB 2L arm block " 3" 6" BB 1
M lift arms " 7" 12fl" BB 2
N wrist pin 1" diameter 2" D 1
O**crank " 2" 6" BB 1
P discs " 2" diameter BB 4
Q fence face " 3" 24" BB 1
R fence base " 2fl" 24" BB 1
S fence blocks " 2" 2" BB 2
T vac port " 3" 4" H 1
U stop bases " 1" 1fi" M 2
V stop blocks fl" 1fi" 4" M 2
BILL OF MATERIALS
7/29/2019 Horiz_Vert Router Table
5/17
out an opening in the center of the top, asshown in Photo B. Remove the spacerstrips and triangles.
3Place the insert on top of the routingguides and the router on top of the insert.
Adjust the depth of cut so the pattern bit justgrazes the exposed edge of the tabletop.Remove the insert, and rout the exposed lipof the tabletop, as shown in Photo C.
4Round the corners of the insert tomatch the corners of the recess, and
drill countersunk " holes, whereshown on the Table Assembly drawing.Use the insert to mark the locations ofthe T-nut holes in the corners of therecess and drill the holes.
Complete thecabinet assembly
1Mount the table assembly C/D/Gbetween the sides of the cabinet
assembly A/B. Insert studded knobsthrough the front holes in the cabinetsides, and screw them into the T-nuts atthe front of the side skirts, as shown onthe Table Assembly drawing. Insert hex
bolts from the inside through the slots inthe skirts and the rear holes in the cabi-net sides. Secure the bolts with knobs.
2Cut two 1812" blanks for thebraces (I) and table guides (J), and
test them for a snug fit, as shown inPhoto D. Trim the blank if necessary,then cut the braces and guides from theblanks, as shown on the Lift Mechanismdrawing. To cut the rounded corners ofthe guides, make copies of the full-sizepattern. Adhere the patterns to the guideblanks with spray adhesive, and jigsawand sand the blanks to the pattern lines.
3Remove the front studded knobs;loosen the rear knobs; slide the table
back; and, pivoting the table on the rearbolts, flip it vertically and lower it untilit rests on the base. Square the table tothe base, and tighten the knobs. Positionthe braces (I) against the back of thetable skirts, as shown in Photo E. Drillpilot and countersunk shank holesthrough the base (A) and sides (B) intothe braces (I), and screw them in place.
4Position the right table guide (J)against the inside of the cabinet, and
push it back against the top of the table.Using the slot in the side (B) as a guide,mark the location of the slot on the tableguide (J). Cut out the slot, and drill thecountersunk shank holes in both guides(J). Now, pin the top between the bracesin the rear and the guides in the front, asshown on the Parts View: Side drawing.Clamp the guides in place, as shown inPhoto F. Using the pre-drilled shankholes as guides, drill pilot holes into thesides, and screw the table guides in place.
5Return the table to its horizontal posi-tion, insert the front studded knobs,
and tighten them. Check the size of thefront opening and, allowing a " gap allaround, cut the doors (K) to size. Drillholes and install the pulls, as shown onthe Cabinet Assembly drawing. Mountthe hinges on the doors, and hang thedoors on the cabinet. Install the magneticcatch. Remove the table and set it aside.
www.woodonline.com 56
Use business or playing cards asspacers to provide working clearancefor the insert.
With the guide bearing of the pattern bitriding on the spacer strips and triangles,cut out the opening.
With the bearing of the pattern bit ridingon the routing guides, form the insertrecess.
Inserted from the front, the blanks for Iand J make a snug fit between the baseand the bottom of the table.
Working from the rear, square the tableto the base, and position the braces.
Clamp the guides to the sides, insertingbusiness cards for working clearance.
A B C
D E F
7/29/2019 Horiz_Vert Router Table
6/17
Fashion thelift mechanism
1Form the arm block (L), as shown onthe Lift Mechanism drawing.
Position it inside the cabinet, centeredunderneath the slot in the right tableguide (J), as shown. Drill pilot and coun-tersunk shank holes through the base(A), side (B), and table guide (J) into thearm block, as shown on the CabinetAssembly drawing, and screw the armblock in place.
2Fasten two 813" blanks for the liftarms (M) together with double-faced
tape. Make a copy of the lift arm full-size pattern, and adhere it to the blanks
with spray adhesive. Drill the holes onyour drill press, then bandsaw and sandthe parts to the pattern line. Separate theparts and set them aside.
3Cut a 2" long piece of 1" dowel forthe wrist pin (N). Using a V-block on
your drill press, drill the counterboredhole, as shown on the Lift Mechanismdrawing. Epoxy one end of a " cou-pling nut into the counterbore and set thewrist pin aside.Note: The longer threaded length of acoupling nut spreads the stress of adjust-ment over more threads and reduceswear on both the nut and threaded rod.
4Make a copy of the crank (O) full-size pattern, and adhere it to a
26fi" blank. Drill the counterboreand holes, and bandsaw and sand theends to shape. Rout the round-over onthe edge of the counterbored face. Bandsawfour 2" discs (P), drill " holes in theircenters, and sand them to finish size.Glue and clamp one of them to the back
(no round-over) of the crank, aligningthe " holes. Set the other discs aside.Glue and screw the wood knob to the crank.
5Assemble the lift mechanism asshown on the Lift Mechanism draw-
ing, using the three discs set aside inStep 4. With the crank and rod assemblyprotruding through the slot in the cabinetside, run the inside lock nut and washerup the threaded rod to the face of thetable guide (J), allowing just enoughplay for the rod to swivel as the mecha-nism is adjusted up and down.
Next build your fenceand a pair of stops
1Cut the fence face (Q) to size. Use adado blade in your tablesaw to cut the
notch in two passes, as shown on theFence Assembly drawing. Prevent tear-out by backing your cut with a woodauxiliary fence attached to your mitergauge. Cut the fence base (R) to size.Rout the chamfer along the back edge,drill the holes, and form the semicircularcutout as shown. Glue and clamp thefence face to the fence base, making surethey form a 90 angle.
2Form the triangular fence blocks (S),as shown on the Fence Assembly
drawing. Glue and clamp them toassembly Q/R, where shown. Cut alength of mini channel 24" long, anddrill and countersink it for #6 flatheadscrews. The Buying Guide lists a sourcefor this channel. Position it on the topedge of the fence, with the front of thechannel flush with the face of the fence.Drill pilot holes and screw the channel inplace. Cut a 34" piece of " hard-board for the vac port (T), and form ahole in it to fit your shop vacuum hose.
58 WOOD magazine December 2000
" slot" long
B
A
" hole
" flat washers
" lock nut
" holes
" hole
" round-over
" counterbore" deep " lock nut
and flat washer
1" dia.wooden
knob
x 9" threaded rod
" lock nut and flat washer
fl" counterbore " deep witha " hole centered inside
" locknuts andflat washers
" holes " holes
1" hole
x 4fi" hexhead bolt and " flat washer
x 3" hexhead bolt and " flat washer
" nylon washer
P
O
N
M
J
I
L
" coupling nut epoxiedinto counterbore
P
P
P
FRONT VIEW
2"
fl" counterbore" deep
" hole
SIDE VIEW END VIEW
1"
1" dowel
N
N
Router Station
" hole
6"
3"
3" 1"
2"
L
12"
12"" holes, countersunk
4fi"
1fi"
J
I
See full-size pattern.
18"
WRIST PIN
LIFT MECHANISM
TABLE GUIDE/CABINET BRACE ARM BLOCK
7/29/2019 Horiz_Vert Router Table
7/17
Screw the vac port to the fence, asshown on the Fence Section View.
3Cut the stop bases (U) and stop-blocks (V) to size. Drill holes in the
bases, as shown on the Fence Assemblydrawing. Secure the bases to the channelwith square head bolts and knobs.Position the stopblocks on the bases,using a square to align them perpendicu-lar to the length of the fence. Clamp thestopblocks to the fence, and drill pilot andcountersunk shank holes through theblocks into the bases. Unclamp theblocks, apply glue, and drive the screws.
Finishing andfinal assembly
1Remove the doors and door hard-ware. Disassemble the lift mecha-
nism, leaving only the arm block (L) inplace. Remove the bolts and knobs fromthe stops and the channel from the fence.Finish-sand all parts and assembliesthrough 220-grit. Apply two coats ofsatin polyurethane to the inside of thecabinet, and all surfaces of the table,auxiliary table, lift arms, crank, rollers,fence, and stops. Sand between coatswith 220-grit sandpaper.
2Prime and paint the outside of thecabinet, including the edges of the
base and sides, and all surfaces of thedoors. We masked off the interior of thecabinet, and used Krylon 2012 CloverGreen/Safety Green spray paint as ourfinish coat.
3Reassemble the lift mechanism,greasing the threaded rod where the
coupling nut runs. Mount the hinges andpulls, rehang the doors, and reinstall themagnetic catch. Cut two 11" lengths ofchannel, drill and countersink them for#6 flathead screws, and screw them tothe top, as shown in the Table Assemblydrawing. Install T-nuts in the corners ofthe insert recess. Screw the previouslycut piece of channel to the fence.
4Remove the subbase from yourrouter, center it on the insert, and use
it to mark the locations of the routermounting screws. Drill and countersinkthe holes, and mount the insert to the
router. Chuck a " brad-point drill bit inthe router, and turning the collet byhand, mark a center point. Remove therouter, and drill a 1" hole in the insert.Remount the insert to the router, thenmount the combination in the top, fas-tening the insert in place with flatheadmachine screws.
5Position the table in its vertical con-figuration by sliding it, front (T-nut
end) first, into the slot between thebraces and table guides and letting itcome to rest on the rear disc of the liftmechanism. Fasten it in place, throughthe slots in the side skirts, with hex headbolts, lock washers, flat washers, andknobs. Position the auxiliary tablebetween the sides, resting on the tableguides. Fasten it in place with four stud-ded plastic knobs and washers.
6Install square head bolts, washers,and knobs on the fence and stops, as
shown on the Fence Assembly drawing.Slide the heads of the bolts in the stopsinto the channel on the fence, and tight-en the knobs. Slide the heads of the boltsin the fence into the channels on thetable, and tighten the knobs.Note: For instructions on using the router sta-
tion, see the following article on page 60. Tobuild the leg stand, see Great Ideas For YourShop on page 28.
www.woodonline.com 59
Written byJ an Hale Svec with Erv RobertsProject Design:Conway Dobbs;J ames R. DowningIllustrations: Kim Downing; Lorna J ohnsonPhotographs: Baldwin Photography
Hole to fit dustcollection orshop vac
x 1fi"square-head bolts
#6 x 1" F.H. wood screws
#6 x 1" F.H.wood screw
" mini channel24" long
" shank hole, countersunk
1" notch 2" long
24"
" pilot hole," deep
1"
11fi"
" holes,countersunk
#8 x 1" F.H.wood screws
" chamferalong back edge
R
S
T
Q
S
" plasticknobs with
threaded inserts
" flat washers
" hole, centered
V
1"
" hole
U
Mini channel
Front offence
TS
R
Align
Q
2"
2"
S
#6 X 1" F.H.wood screw
"
"
4"
1fi"
" holes,countersunk V
1fi"
1"
"
" hole,centered
U
2fl"1fl"
fi"" hole
fi"
12"
" chamfer24"
R= 1"
Location of
R
S
FENCE BASE
FENCE SECTION VIEW
FENCE ASSEMBLY
FENCE BLOCKS
STOPBLOCK
STOP BASE
7/29/2019 Horiz_Vert Router Table
8/17
BASE
A
25"
12"
17"
"
" holes, countersunkon bottom side
Location of
Location of
Location of
Location of
3fi"
22"
" hole" hole
" hole
" hole
3"3"
2fi"
2fi"
L
J
I
I
10"
1fi"
3"
16"
9fl"
" holes
x " slot (right side only)
"
17"
" rabbetfi" deep
10" 1"
4"
1"
*"
B
" hole,countersunk
" hole, countersunk(right side only)
22"
12"
SIDEINSIDE VIEW
(2 needed)
14""
Location of Table assemblyin vertical position
Location of ILocationof L
Locationof J
*Minimum of "for door clearance,trim if necessary.J
PARTS VIEW
WOOD PATTERNS insertParts View drawings
7/29/2019 Horiz_Vert Router Table
9/17
Router plate cutout
" rabbet, depth same asthickness of insert plate
" groove" deep(size to fit yourmiter gauge)
24" """ stopped rabbets " deep
11"
22"
4"
12"
11"
" holes,countersunk
TOP
G
10"
11"
2"" hole, allfour corners
PARTS VIEW
WOOD PATTERNS insertParts View drawings
7/29/2019 Horiz_Vert Router Table
10/17
FULL-SIZE
PATTERNS
O
"hole
"counterbore"deep
"hole
"round-over(on
facesideonly)
2"
6"
Alignwithcorne
rofblank. J
TABLEGUIDE
(2needed)
CRA
NK
To ensure full-size patterns are correctsize, your printer should be set to printat 100% (not fit to page). Measure
full-size patterns to verify size.
1"
fi
WOOD PATTERNS insertFULL-SIZE PATTERNS
7/29/2019 Horiz_Vert Router Table
11/17
WOOD magazine OCTOBER 2000
" hole
Join pattern here.
To ensure full-size patterns are correctsize, your printer should be set to printat 100% (not fit to page). Measurefull-size patterns to verify size.
1"
fi
M
LIFT ARM(2 needed)
WOOD PATTERNS insertFULL-SIZE PATTERNS
7/29/2019 Horiz_Vert Router Table
12/17
" hole
1" hole
M
LIFT ARM(2 needed)
Join pattern here.
To ensure full-size patterns are correctsize, your printer should be set to printat 100% (not fit to page). Measurefull-size patterns to verify size.
1"
fi
WOOD PATTERNS insertFULL-SIZE PATTERNS
7/29/2019 Horiz_Vert Router Table
13/17
60 WOOD magazine December 2000
Use the workpiece to set the fence as a hold-down. The stock must slide smoothlythrough from end to end for safety and a precise cut.
horizontal/
verticalrouter table
Our two-way table, described in the preceding
pages, makes already versatile plunge routers
even easier to use. J ust follow these steps to
get smooth results every time.
You already know how useful yourrouter can be with the bit pointedstraight up or straight down. But
have you ever thought about what wood-working feats you could accomplishwith it mounted horizontally? Youllfind that several operations, such as rais-ing panels, mortising, and tenoning,become much easier and safer with thebit parallel to the work surface and theworkpiece lying flat.
Get thehorizontal advantageVertical panel-raising bits and someedge profile bits work great with theback table upright and the router hori-zontal. Youll have to cut an opening inthe auxiliary table thats big enough toaccommodate the largest bit that youplan to use. See the photo below.
how to use the
Only part of the bit extends above thework surface in the horizontal setup, soyoull have to cut an opening to accom-modate the rest of it. We made ours 2"long and 1" wide, big enough to let thispanel-raising bit spin freely.
7/29/2019 Horiz_Vert Router Table
14/17
Raise the fence out of the way, andloosen the knobs holding the verticaltable. Turn the crank on the side of thecabinet to adjust the depth of cut, thenretighten the knobs. Note that youll feedstock from left to right. The photo on
page 60 bottom left shows our handyreminder, printed and drawn right on thefence with a dark, permanent marker.
In this position, your fence serves as along hold-down. Place the workpieceflat on the front table. Then lower thefence until it contacts the piece lightlyand evenly, from end to end. Again, seethe photo.
Take several light cuts to shape a pro-file, finishing up with a setting that justskims the surface. Youll get thesmoothest possible result that way.
We built one more accessory, a hold-down block, to use for mortise and tenonwork at the end of a narrow board, or onthe side of a narrow stile. See the draw-ing above right for the dimensions anddetails. It fits into the channel on thefence and keeps the workpiece securewhile providing a clear view.
An upcut spiral bit excels at mortiseand tenon tasks. Install one in yourrouter, use a couple of test pieces to setthe height and depth, and transfer yourlayout lines from the workpiece to theauxiliary table. When working on a shortstile, use both stop blocks to control thecut. Youll be limited to one stop blockwith longer workpieces. As shown in the
photo above right, you can even cut intothe end of a rail for loose tenons.
To form standard tenons, set the depthof cut, place the hold-down block in con-tact with the workpiece face, as shown inthe photo above left, and cut the tenonsside shoulders in one or more passes.Use the miter gauge to support the work-piece. Loosen the fence knobs and resetthe height of the hold-down block whenyou flip the rail on edge to cut the finaltwo shoulders.
Go verticalwhen necessaryNow lets say you want to reset therouter to its vertical position so you canuse a large-diameter panel-raising bit.Loosen the bolts that hold the auxiliarytable in place and remove it. Loosen thebolts that hold the main table and crankthe lift mechanism as low as it will go.
Slide the table up and out of its slots,pivot it back and down, and fasten itwith the knobs and bolts.
Now youre back to the more familiarrouter table arrangement. Take advan-tage of the miter gauge slot to guidewide pieces with your tablesaw mitergauge. Use the stop blocks to makeaccurate stopped dadoes.
Remember, the design calls for aplunge router, and you must keep theplunge mechanism unlocked to adjustcutting height. Now the crank forces therouter up along its plunge rods for adeeper cut or lowers it for a lighter cut.
Make sure to tighten the knobs on thefence every time you reposition it. Feedstock from right to left in this setup, anduse a featherboard when possible.
www.woodonline.com 61
For mortising, set both stop blocks whenever possible.Guide the stock with your miter gauge.
4"
4"
21/2"
2" 1"
3/8" hole
3/8" plastic knobwith threaded insert
3/8" square head bolt 11/2" long
#8 x 11/4" F.H. wood screw
5/32" shank hole,countersunk
3/8" flat washer
Photographs: Baldwin PhotographyIllustration: Roxanne LeMoine
Slide the hold-down block into the fencechannel, and center it whenever youneed to keep a narrow piece in place.
HOLD-DOWN BLOCK
7/29/2019 Horiz_Vert Router Table
15/17
28
for your shopg r e a t id e a s
Aleg stand, with its tapered andslightly splayed legs, makes asturdy, yet good-looking base for anymachine. In fact, the router table on
page 54 rests squarely on one. Use thedimensions shown here in the Bill ofMaterials to make one for the routertable or, alter the lengths of the partsand make one to fit a machine in yourshop. To size the parts for anymachine, follow these guidelines: 1)
Subtract 158" from the length of themachine for the length of the side rails(A). 2) Subtract 314" from the width ofthe machine for the length of the endrails (B). 3) Subtract 3" from the lengthof the side rails (A) for the length ofthe cleats (C). 4) Multiply your desiredheight by 1.074 for the length of theblanks for the leg halves (D). Screw apiece of plywood to the cleats and boltyour machine to it. Now, heres how toput your leg stand together.
After cutting the rails (A) and (B) tothe dimensions shown on the PartsView drawing onpage 30, screw themtogether to form a rectangular frame. Fitthe cleats (C) into the rail frame andscrew them in place. Set the frame aside.
Cut blanks for the leg halves (D) tosize, and before forming the legs, drillthe holes where shown. Remember tomake mirrored pairs. Bevel-rip themating edges. Then, with the sawblade tilted at the same angle, cut the
leg standfor stationary tools
spline slots in the bevels. Next, makethe angled and beveled cuts at the topand bottom of each leg half. Do not cutthe leg tapers until the halves havebeen glued together.
WOOD magazine December 2000
441/2O
bevels onoutside corners of legs
9O
bevels alongall top edges
3/8" holes
3/8 x 2"carriage bolts
1/8 x 1/2 x 26"hardboard spline
3/8" flat washer and bolts
EXPLODED VIEW9O
bevels along side and ends
3
/8
" holes for mounting router table cabinet
#8 x 2" F.H. wood screws
1/8" splineslots 1/4"deep
No bevel on this edge
#8 x 2" F.H.wood screws
C
B A
A
B
D
D
D
1/4" round-overs
D
D
C
Continued on page 30
Materials Key: Mmaple
Supplies: " tempered hardboard, 2" carriagebolts, flat washers and nuts (16), #82" flathead woodscrews (16), finish.
finished sizePart T W L Matl. Qty.
A side rails " 5" 25" M 2
B end rails " 5" 20" M 2
C cleats " 1fi" 22" M 2
D leg halves " 6fi" 27" M 8
BILL OF MATERIALS
7/29/2019 Horiz_Vert Router Table
16/17
PARTS VIEW
271/8"
3/4"
5"
20"
9O
bevel along top edge9
O
B
END RAIL
LEG HALVES
C
221/4"
11/2"
9O
bevels3/8" holes; mark locationsusing holes in cabinet base.
CLEAT
5"
251
/4"
9O
bevel along top edge9
O
A
Cleats are located here.C5/32" holes, countersunk
SIDE RAIL
3/4"
3/8" holes
44.5O
bevel
4"
15/8"
31/2"
11/4"
9O
bevel alongtop edge
31/4"
61/2"
9O
9O
9O
bevelalongbottom edge
D
30 WOOD magazine December 2000
Clamp the frame upside down on
your workbench. Apply glue to themating bevels of the leg halves, andinsert the splines. While holding thehalves together by hand, clamp thelegs to the frame. This holds thehalves at the proper angle while youfinish clamping the length of the leg,as shown in the photo at left. Whenthe glue is dry, mark the tapers on thelegs, and cut with a jigsaw or band-saw. Clean up the cuts with a coupleof passes over your jointer. Rout theround-overs, and using the holesdrilled in the legs as guides, drill the
holes in the frame.
for your shopg r e a t id e a sContinued from page 28
Bolt the legs in place, and if needed,
cut a piece of plywood and screw it tothe cleats. Place your tool on the stand,and mark the locations of the mountingbolts with a pencil.
Drill the holes and apply the finish ofyour choice. When the finish is dry,bolt your machine in place and enjoysafe, rock-solid woodworking.
Written byJ an Hale Svec with Erv RobertsProject Design:J ames R DowningIllustrations: Kim Downing; Lorna JohnsonPhotographs: Baldwin Photography
leg stand
Clamping the legs (D) to the frame (A/B/C)holds them at the proper angle while you
finish clamping their length. Copyright Meredith Corporation 2000
7/29/2019 Horiz_Vert Router Table
17/17
,
Issues 1209
Easy-to-make
WineCabinet
WOODBetter
HomesandGar dens
IS S U E 1 7 2 OC T OB E R
2 0 0 6
WOOD1 7 2
OCT OBER2 0 0 6
$6.99U.S./
$7.95CAN.
D is pla y un tilO c to b er 10 , 2 0 0 6
AGREA T
WEEKEN D
PROJECT!
p.82
END-GRAINCUTT ING B
OARD
21WorkshopC lutterBustersp.90
Add to YourSkillsCutPerfe c tly Straight Edge s p.76Tune Upy our Bands awp. 52Ke rf-BendPly wood
p.32
Improve YourShopSpace-s av ing ToolStorage
p.4610Air Cle aners Te s tedp.70
BetterH omesandGardens
I SSUE178SEP TEMBER 2
007
F R E E F U L L - S I Z E
PATTERNSI NSI D E
$6.99
U.S./$7.95CAN.
Displayunt il August 28, 2007
HeirloomCradleCr aft i t thisweekend.Cher ish itfor generations.
47Time-andMoney-SavingT ipsInside!
20ToolsTested12" Mitersaws Parallel JawC lampsS teelRules
MoreGreatP rojects S pace-sav ingOutfeedT able
T ablesawAlignment JigC atchall Box T ower S helv esBistroS tool
BuildYourSkills Clam pingS ecrets
No-slipM iters T emplateRoutingF aux F inishes
St or es fat in
it s own c as e!
BetterHomesandGardens
ISSU E186 OCTO
B ER 2008
$6.99U.S.
Disp la
yuntilOctobe r
7,2008
11Easy-to-Build Projects Inside
200m.p.h.&madeofwood!Youneedtoseeit tobelieveit. p.50
TRIOOF TABLESp. 32CH IN ESECHECKERS p. 72 MITERSAWSTAN D p. 44
EXCLUSIVE!
PLUS
31T OOL S T E S T EDI N
THI S I SSUE
WeTest&RanktheNewest18-VoltLithium-IonDrills
ISSU E 209D EC/ JA N 20
11/2 012BetterHomesand Gardens
TurnStockCabinets intoFurniture!p.32
Ma k e th ista ll ch e st , and other f n e u rn itu re ,the EAS Yway.Great
Projects!JewelryBoxp.38CarouselMusicBoxp.45BackgammonBoardp.50RockinTruckp.63
WeTest&RanktheNewest18-VoltLithium-IonDrills p.58
$6.99U.S.
D isplayunt il Janua
r y17, 2012
53S h o p
T i p s I n s i d e
!
September1984Dec/Jan2011/2012
In a Searchable Digital Format
27Yearso
f
Issues!
WOOD Complete Back Issues
TIE: r uti n r istriuti n fth ntnt fthis r ut is stritlr h i i t . u r h s f t h is r u t s n t t r n s f r n ti t l r ri h t s f n -r sh i in t h n t n t t t h u r h sr . Th n t n t ft h i s r u t i s r t t
r i h t n m n t u s f r n t h r u r s i t h u t th r i t t nr m is s i n f t h r i h t n r . r i h t r i t h r r t i n 1 .
l l r i h ts r s r . r u i n t h U .
Browse more than 1,300 woodworking project plans, DVDs, back-issue collections, videos, tool reviews, books, & more.
Everybodys a tool critic. Now its your turn!
Readers rely onWOOD
magazine for unbiased reviews ofwoodworking tools
and accessories.
Youll find them here,
all in one place. While
youre there, add
reviews about the
tools in your shop.
Just click to compare
specs, prices,
and more.
Plans Complete Guide DVD-ROMs Videos Back-Issue Collections
The biggest names in woodworking
help you build your skills with
affordable videos (up to 2 hours long).
Save money by doing the download.
Watch free videos of other
woodworkers showing their stuff,
from shop tips, to favorite jigs, to...
well, just about anything!
Dont spend a penny on a tool until
you learn how it works. Tool School is
like having a free woodworking show
on your desktop!
WOOD magazine editors provide
videos that enhance the content in
the magazine. New videos added
regularly.
A wealth of information just a click away.
WOODmagazine.com speaks to woodworkers of all skill levels withfree woodworking
plans, helpful
forums, hundreds
of articles, and
more services to
help you become a
better woodworker.
Visit theWOOD
familyof helpful Web sites!
Watch a demo before you buy
FREE magazine support 24/7DVDs or downloads
By woodworkers, for woodworkers