Working principle and some Design Concept of Hovercraft
Abstract
A hovercraft is an air-cushioned vehicle that is, it does not require wheels like other
automobiles, and hence surface friction is not a factor for a hovercraft. A hovercraft can
go over land as well as water without any difficulty and is majorly used in marshy areas
for patrolling and defense applications. A hovercraft is also used for tourism. A
hovercraft works on the principle of propulsion and is futuristic vehicle and can be used
in many defense and miscellaneous applications.
Department of Mechanical Engineering
Bangalore Institute Of Technology, v.v.Puram, Bangalore 1
Working principle and some Design Concept of Hovercraft
PRINCIPLE OF WORKING
A Hovercraft or also called an air cushion vehicle is a vehicle that can drive on both land
and water. This vehicle differs from other vehicle in that way, it needs no surface contact
for traction. Obstacles such as gullies and waves can be taken very easily like it is a flat
surface. The reason for this is a generated air cushion between the hovercraft itself and
the ground surface.
The Hovercraft lifts due to the pressure generated by the air in the chamber {formed by
the bottom portion of the hull and the skirt]. We know that Pressure = Force /Area {P/A]
this relation gives the pressure required for the lift of the hovercraft.
So the Hovercraft lifts due to the pressure by the fan and hence floats above the ground.
Air leaks from below the skirt. This loss of air is taken care by axial flow fan, which is
continuously supplying air to the chamber. Flaps are provided to help uniform air leakage
from the bottom of the skirt. As the craft is above the ground there is no friction between
the ground and the craft, now the craft is propelled with the help of the propulsion fan.
The control of direction is done by using rudder and a steering mechanism.
In the hovercraft are placed two propellers both driven by a gasoline engine and one of
them is used to provide lift by keeping a low-pressure air cavity under the craft full of air.
As the air pressure is increased the air lifts the craft by filling the cavity. The cavity or
chamber in which the air is kept is called a ‘plenum ‘chamber. At the point when the air
pressure equals the weight of the hovercraft over the chambers surface area the hovercraft
lifts and the air starts to escape around the edge of the skirt. The escaped air creates an
air-lubricated layer between the hovercraft and the ground surface. This will lead to a
Department of Mechanical Engineering
Bangalore Institute Of Technology, v.v.Puram, Bangalore 2
Working principle and some Design Concept of Hovercraft
frictionless motion of the hovercraft, taken into account that the minimum contact
between skirt and the ground surface during the motion is negligible.
The amount of the total weight that a hovercraft can raise is equal to the pressure in the
plenum chamber multiplied by the area of the hovercraft. This plenum chamber principle
is visualized in fig. 1.
A constant feed of air is needed to lift the hovercraft and to compensate for the air being
lost through the holes in the bottom plate.[1] The flow must also be greater than the
amount of air that escapes through the holes in the bottom plate. The rate of air loss is not
constant, because there is no way of ensuring that any air escapes evenly all around the
hovercraft. To maintain also the lift, the engine and propeller have to be sufficiently
powerful enough to provide a high air flow rate into the chamber. A cylinder is placed
around the lift propeller to improve the efficiency, because it reduces the pressure loss
around the propeller tube. The second propeller is driven by another motor and is placed
on the back end of the hovercraft. This motor can only deliver a constant speed to the
propeller in contrast to the lift propeller and is used to generate a displacement forward.
Department of Mechanical Engineering
Bangalore Institute Of Technology, v.v.Puram, Bangalore 3
Working principle and some Design Concept of Hovercraft
Without a rudder the hovercraft is un-maneuverable. Rudders action not only creates
turning moment but also a drifting force and rolling moment, which leads to an outward
banked turn.
HOVERCRAFT TERMINOLOGY
AIR STRAIGHTENERS:
The stator blades which serve to form the air into a straight line thrust.
BAG SKIRT:
Older versions of hovercraft used continuous skirt which looks like an inner tube.
DRAG FLAP:
Flap under rear skirt which prevents skirts from scooping up water and increasing drag.
FAN DUCT:
The circular structure around the fan which assists its efficiency and houses the air
straighteners.
HOVER HEIGHT:
The height of the hard structure above a hard surface at operating speeds.
HUMP:
When starting on water the lift air creates a saucer in the water and climbing out of it is
called flying over hump.
ON CUSHION:
The position of the hovercraft when the hard structure is clear of the surface riding on its
cushion of air.
Department of Mechanical Engineering
Bangalore Institute Of Technology, v.v.Puram, Bangalore 4
Working principle and some Design Concept of Hovercraft
SEGMENTED SKIRT:
Skirt made up of individual pockets, segments of fingers, each separately supplied with
lift air.
SKIRT TIES:
Plastic ties which hold the skirt segments to the skirt tie anchor on the hull.
TRIM:
Posture of the hovercraft when flying or floating; this may be nose-up, nose-down or
leaning left or right. Ideally the craft should be level or slightly nose up.
The various parts are as shown in the figure 2.
Figure 2: Hovercraft parts
Department of Mechanical Engineering
Bangalore Institute Of Technology, v.v.Puram, Bangalore 5
Working principle and some Design Concept of Hovercraft
HULL
[1] The hovercraft hull is a solid structure which forms the base of the hovercraft which
supports the lift and thrust systems and also the driver.
For amateur hovercraft builders, plywood is the material of choice. Plywood is
affordable and easy to use. Plywood has a better “strength to weight” than steel and is
much lighter than most fiberglass hovercraft. When encapsulated with epoxy resin,
plywood is as durable and as low in maintenance as any other material. Plywood
hovercraft can be built with basic hand and wood working tools.
[2] The joining of the plywood is a “stitch and glue” method. Panels are cut to shape from
plans and joined together at the seams. A hovercraft can be assembled quickly after all the
panels are cut out.
Department of Mechanical Engineering
Bangalore Institute Of Technology, v.v.Puram, Bangalore 6
Working principle and some Design Concept of Hovercraft
SKIRT
The skirt is one the most important parts of a hovercraft as it is the part that allows the
hovercraft to clear obstacles. Generally speaking the higher the skirt, the larger the
obstacle that the craft will clear. However, if the skirt is too tall, the craft will ‘slides off
the cushion and the cushion will deflate or the craft will become extremely unstable.
The invention of the flexible skirt was a big step forward in the hovercraft history. Before
the flexible skirt had thought necessary, powerful lift engines were needed to create only
a few millimeters lift under the hull hard structure. The main idea behind the air cushion
introduction was to create air lubrication between the ground surface and the hovercraft,
in a way that leads to a significant of the lift power. The use of an inflated bag around the
hovercraft resulted in an efficient air distribution and a reduction of the lift power. Other
advantages of the flexible skirt development are a better stability and a better obstacle
clearance. The function of skirts for a hovercraft has proved to be as important to the air
cushion vehicles as that of the rubber tyres for an automobile. The material type and the
structure of the skirt are playing an important role in the skirt design step. The material
for a skirt bag should have high tearing and tension strength, but with as few as possible
abrasion. [3] The skirt bag is normally divided in several parts to improve the absorption
of obstacles.
Types of skirts
i. The bag skirt
ii. The segmented skirt
iii. The juped skirt
RUDDERS
Department of Mechanical Engineering
Bangalore Institute Of Technology, v.v.Puram, Bangalore 7
Working principle and some Design Concept of Hovercraft
Rudders are important for steering the craft. Besides their steering capability they
have a nice effect to increase usable thrust. As the propeller of fan turns the air will
generate swirls and the rudders will straighten them again. They actually act as flow
straighteners.This is why most hovercraft have more than one rudder (besides the higher
steering forces you can achieve covering more flow area).
[3] An important aspect of rudders is their drag. Build wrong they may consume more
thrust for drag then you can gain from straightening the flow so they should be made
keeping this in mind. The highest drag is from a flat plate. Round at least the corner
towards the propeller or fan and send the other side flat. A better solution would be to use
an airfoil shape. The rudders can actually made thicker with less drag than what you
would achieve with a flat plate. It doesn’t have to be a complicated airfoil, a NACA000x
(where x stands for the thickness in %) will do the job.
The pivot point of rudders is usually at 1/3 of the chord (the depth of the rudder) this
helps to lower the steering forces. The force on the forward third is compensated with the
third behind the pivot point so the force you have to hold with your steering is only the
one on the rearward third (.times the lever).
Unfortunately rudders have a less nice side effect; they also act as an elevator or push the
hull down on the outside of the curve. This can be either compensated with an elevator or
special rudder arrangements. A rudder setup, which compensates this negative effect and
Department of Mechanical Engineering
Bangalore Institute Of Technology, v.v.Puram, Bangalore 8
Working principle and some Design Concept of Hovercraft
even supports leaning into the right direction, is the one shown in the figure 3 below. The
upper rudder pivot point is set back behind the lower pivot point. What this does is that
the rudders are just straight up if you drive straight ahead. As soon as you turn them the
top part will fold a bit downwards and generate some lift. Set up right the craft will nicely
lean into the curve.
Figure 3: Normal and Angular Rudders
Another method, which combines rudders and elevator into one unit, are inverted V
rudders as shown in the drawing below. The disadvantage of this setup is that the linkage
Department of Mechanical Engineering
Bangalore Institute Of Technology, v.v.Puram, Bangalore 9
Working principle and some Design Concept of Hovercraft
gets complicated. For a turn the rudder pairs have to turn in opposite directions. If you
want to make a left turn the left rudder pair has to go up and the right pair has to go down.
The same for a right turn, just into the opposite direction. To use the rudders as an
elevator all rudders have to move into the same directions (All up to lift the bow, All
down to push the nose down.). To make the situation worse it may be required for fine
trim of the craft to have one rudder pair go up more than the other pair down for curves.
This may be the reason why this excellent rudder arrangement isn’t used for most
hovercrafts (Refer figure 4). It more or less demands that the rudders are actuated by a
fly-by-wire system have the mechanical design would be a nightmare.
Figure 4: Inverted V - Rudders
Very important for all rudders arrangements is to keep the play in the hinges as low as
possible to avoid that the pilot has to continuously play with the steering. The same
applies for the mechanical strength of all attachments. They should be made strong
enough not to flex which would also result in problems similar to the once with too much
play in the hinges.
POWER TO WEIGHT RATIO
Department of Mechanical Engineering
Bangalore Institute Of Technology, v.v.Puram, Bangalore 10
Working principle and some Design Concept of Hovercraft
Although an air cushion vehicle does not require the critical power-to-weight ratio
precision as does an airplane in order for it to still operate, it is nonetheless necessary to
consider the power-to-weight ratio at the design stage of an air cushion vehicle, rather
than find out later that there isn’t enough power to lift or move the craft.
The power-to-weight ratio determines in large part the amount of ground clearance
between the skirt and the ground surface. The greater this round clearance the more
efficiently the propulsion system operates. That is not to say that the higher the hovercraft
lifts into the air the better. Lifting it too high will cause instability.
Such is the power of the lift that even a severally overloaded and miscalculated power-to-
weight ration hovercraft construction will still work, but it is far from ideal.
Power-to-weight ratio = P / W
POWER TO WEIGHT TO STRENGTH RATIO
The next consideration for a properly functioning hovercraft is the power-to-weight-to-
strength ratio. This deals with the structural strength of the raft to be light enough to be
lifted by the air cushion created underneath, yet strong enough to carry the weight of the
engine, its passengers or payload.
Department of Mechanical Engineering
Bangalore Institute Of Technology, v.v.Puram, Bangalore 11
Working principle and some Design Concept of Hovercraft
Air cushion vehicle hull construction is more closely based on aviation rather than marine
construction for the simple reason that aviation hulls are a combination of strength and
lightness as opposed to strength as a priority.
Although wood and plywood are often used, many hovercraft hull structures are made of
aluminum skin, welded or riveted onto an aluminum web or frame. Enclosed spaces are
sealed to provide airtight compartments for natural buoyancy.
A hole in the raft can be made to feed air to the plenum chamber beneath the craft.
However, the use of the new skirt techniques makes peripheral jets, led in from the edge f
the raft through ducts, more sensible and more common.
Other crafts use aluminum-honeycombed paneling to provide the buoyancy, and fiber
glass and composite materials, such as PVC, are becoming more popular as they combine
strength, lightness and buoyancy in a single material.
Department of Mechanical Engineering
Bangalore Institute Of Technology, v.v.Puram, Bangalore 12
Working principle and some Design Concept of Hovercraft
Figure 5: Fan placement and the airflow in a Hovercraft
THE DESIGN PROCESS
Department of Mechanical Engineering
Bangalore Institute Of Technology, v.v.Puram, Bangalore 13
Working principle and some Design Concept of Hovercraft
In designing Hovercraft one of the first steps is to decide what is needed that is nothing
but specifications. Difficult as it always seems, the designer must try to write out a series
of requirements. Size, weight, performance, control, cost, noise, life expectancy,
appearance, and comfort are the contents in the specifications. Improper specifications
soon become apparent and consequently, specifications often needed a revision. Conflicts
arise and compromise becomes unavoidable. Probably the most common specification are
Size, Cost, Performance, Dependability / maintenance, appearance and capabilities.
Hovercraft lift calculator
Department of Mechanical Engineering
Bangalore Institute Of Technology, v.v.Puram, Bangalore 14
Working principle and some Design Concept of Hovercraft
Enter the required data in the following fields; use the metric or imperial boxes, not both.
When done, press the "Calculate" button. The answers will appear below. Press the
"Clear Input" button before starting a new calculation.
Top of Form
Enter hull length in meters: or feet:
Enter hull width in meters: or feet:
Enter Amount of air gap required in mm (i.e. 13): or inches (i.e. 0.5):
Enter max. gross weight of craft in kg: pounds:
.
(m) (ft)
Total hover gap area (m^2) (sq. ft.)
Total cushion area (m^2) (sq. ft.)
Cushion pressure (N/m^2 = Pa) (lbs/sq. ft, PSF)
Cushion pressure(mm of water @
4degC)
(inches of water @
60degF)
Expected actual air
velocity(m/sec) (ft/sec)
Lift air volume (m^3/sec) (CFS)
Estimated lift engine
power(kW) (HP)
Estimated fan diameter (m) (inches)
Department of Mechanical Engineering
Bangalore Institute Of Technology, v.v.Puram, Bangalore 15
Working principle and some Design Concept of Hovercraft
Results below are computed from the Input Data above and
are to be considered approximate values only.
Table 1: Hover calculator
(Readings)
7.4 BAG SKIRT:
Recently the most widely used skirt was the bag skirt, which is like a giant inner
tube fitted around the crafts perimeter. Additional pressure is needed to inflate. The bag
against air pressure under the craft in the cushion.
BAGS
The bag is popular as its manufacture uses the least amount of material compared to other
skirts types. There is usually little or no wastage. In the US this is still the most common
skirt found on home built machines. Fabrics for bags are usually the same as for jupes,
which is 5.21N/m2. Neoprene coated nylon.
The nylon-base fabric is usually about 2.33N/m2.
Bags are of two types, flow through and non- flow through.
Drape the material over the corner and mark the shape of the joint. Allow a 0.0254m glue
seam. Seams should always lay in the direction of travel as much as possible.
Now it is very important that the relative position and shape of each corner with respect to
each other corners be obtained before cutting the final skirt panels.
Making skirt is an art. The simpler the craft shape the easier fitting the bag becomes. Coat
the thread with epoxy or urethane to prevent fraying. Bags can be fitted to the curved
Department of Mechanical Engineering
Bangalore Institute Of Technology, v.v.Puram, Bangalore 16
Working principle and some Design Concept of Hovercraft
Hulls and other odd shapes but with more difficulties. The draw back of this approach is
that no two skirts will be alike and each hovercraft could have different characteristics
depending on the quality and actual shape of the skirt.
Bags assume different cross section shapes depending upon the attachment points; the
pressure ratio between the bag and the cushion, as well as the local skirt height. Creases
in the bag will cause drag, wear and uncomfortable operating characteristics.
For best results when bonding skirt seams, properly clean, glue, and rivet using solid
aluminum rivets with large flange aluminum backing washers placed on each side of the
seam and spaced about 0.0381 m apart. However, neoprene contact (weather stripping)
cement will, for most applications, be adequate.
There is a natural tendency for bags to bounce. This is especially bad over smooth hard
surfaces like concrete and ice. Diaphragms fitted internally will reduce bounce but this
solution is uncommon. Instead several strips of skirt material are sewn along each side of
the bag to help damp out oscillations and act as a spray deflector. Its is tough that bounce
is more slightly to occur when the bag cushion pressure ration lies between 1.2 and 2.0 of
course this is the ratio at which most bags operate.
Non- flow-through bags are usually inflated through a splitter plate connected by a small
duct placed directly under the lift pan in the fan duct. Its size is usually 10% of the lift
duct area. The remaining duct area provides the lift air for the cushion. For best overall
craft performance lift air should be introduced into the forward part of the cushion.
Department of Mechanical Engineering
Bangalore Institute Of Technology, v.v.Puram, Bangalore 17
Working principle and some Design Concept of Hovercraft
ENGINES:
The lack of engines specially developed for hovercraft use has been, and continues to be ,
a serious impediment to the production of low cost, reliable, high performance hovercraft.
Some types of engines are most suitable than others, but all have been adapted and thus
all types have problems when used in hovercrafts.
FAN
The requirements of the fan are that it must provide the required volume of air at the
required pressure.
PRESSURE REQUIREMENT
The definition of pressure is the force exerted per unit area.
Department of Mechanical Engineering
Bangalore Institute Of Technology, v.v.Puram, Bangalore 18
Working principle and some Design Concept of Hovercraft
Cushion pressure = Total weight of the craft / area of the cushion.
As the cushion pressure is selected to offset the craft and thereby provide lift, [3] any
change in craft weight or pay load, will require a change in cushion pressure. Any change
in hover gap will result in variation of the air volume required to maintain the cushion. In
practice, this variation occurs in the change in surfaces over which the craft travels. As a
consequence, it is necessary for the fan selected to supply sufficient pressure and volume
in different conditions specified.
Here,
.
Total pressure inside the skirt, Pt1 = 823 + Ps1 ------------------------ (1)
Total pressure outside the skirt, Pt2 = 823 + Ps2 ------------------------ (2)
We know that when the air leaves the system all the static pressure is converted into
velocity pressure.
Therefore total pressure as only one component viz.., velocity pressure.
We know velocity pressure = ½ ρV2
Where,
ρ = density of air
V= velocity of air
Flow rate,
Qnom = V * A
Qnom = √ (2 * Pc / ρ)* h* CPc * Dc.
The discharge coefficient ‘Dc’ depends on the angle formed between the skirt and the
ground and is found from Von Mises equation.
Dc= 0.5 + (0.4 * 10^-3) * θs + (0.109 * 10^-4) * θs2 - (0.494 * 10^-7) * θs3
Department of Mechanical Engineering
Bangalore Institute Of Technology, v.v.Puram, Bangalore 19
Working principle and some Design Concept of Hovercraft
+ (0.345*10^-9)* θs4.
For 45 degree skirt angle the Dc=0.537.
Design factor to account for non-ideal surface conditions (Ks).
Typical design factors
Ice = 1.
Hard mud = 1.2.
Very short or wet grass = 1.3.
Sand or 4" grass (pliable) = 1.4.
Short course grass = 1.5.
Wet or sticky mud or Long pliable grass = 1.6.
Very choppy water or long course grass = 1.7.
Very sticky mud or shallow shale 1.8+.
Assuming Ks =1.8
Therefore,
Cushion design flow rate,
Q =Qnom*Ks m3/ sec
Depending on this value we select appropriate fan.
ENVIRONMENTAL IMPACT OF HOVERCRAFT
For the majority of the people hovercraft is a new experience. Our knowledge of them
is usually gleaned from newspapers, television, magazines and the like, and
consequently misconceptions are ripe.
For any vehicle to operate economically the drag, or resistance to motion, must be
kept to a minimum. The majority of the drag arises from the vessels hull through the
water; therefore we can reduce the drag and consequently propulsive power by
Department of Mechanical Engineering
Bangalore Institute Of Technology, v.v.Puram, Bangalore 20
Working principle and some Design Concept of Hovercraft
minimizing hull contact. The hovercraft achieves this by using low-pressure air to
form air cushion beneath it, thus actually lifting the hull clear of water. The main
point here is that because the hovercraft does not pierce the surface over which it is
traveling the advantage is two-fold:
a) less friction = less fuel burnt to move,
b) Less friction or interruption to the surface = less disturbance of the environment.
Therefore hovercraft can be used to best advantage in shallow water and drying areas,
these areas often being remote and environmentally sensitive. Most of these areas are
wetlands, swamps, and river delta. They are not only the feeding ground for a lot of
different species of birds as well very often used for marine live for hiding from
predators. In these sensitive areas are nearly to transportation means available.
Hovercrafts are able to operate in these areas in an environmentally friendly way.
Being amphibious the hovercraft can use direct routes across sand banks, marshes and
flats, with no loss of speed and comfort, with no loss of speed or comfort. Channel
dredging becomes unnecessary, whilst rivers and tidal estuaries present no problem
for the passage of the vessel. Previously inaccessible areas may be accessed
Economically with little or no impact on their environment. If this area is a future
wetland where nobody could proof that it is a wetland or not-since it was not
accessible by traditional transportation means, or a very shallow bay where you need
to download your data from your instrument platform. With the Hovercraft you can
reach destinations which where before not accessible for research and studies.
Damage to the shore environment, such as beaches, mud flats and vegetarian is
virtually nil because of the hovercraft’s low pressure “footprint”. For example, the
average human being when standing on a beach exerts a pressure of some
0.021N/mm2 underfoot, rising locally to 0.0172 N/mm2 when walking. The average
hovercraft by comparison, exerts a pressure of only N/mm2 on the surface regardless
of speed. This “footprint” pressure is less then that of a seagull standing on one leg.
Department of Mechanical Engineering
Bangalore Institute Of Technology, v.v.Puram, Bangalore 21
Working principle and some Design Concept of Hovercraft
All advanced Hovercrafts are fully amphibious and create virtually no under water
noise, just atmospheric noise levels which would typical of truck or bus. The fact that
there are o underwater protrusions eliminates the usual thrashing noise signature
associated with conventional propeller driven craft, as well as negating any possible
sea bed erosion when operating in shallow waters. It therefore becomes obvious that
fish and other marine life are in no way affected. This has been confirmed by
independent scientific tests. The major noise factor with any hovercraft is the air
propeller noise, which in case is largely directional in characteristic and more
apparent to above surface creatures like humans. To minimize this effect advanced
hovercraft propulsion propellers have been designed with low tip speed to minimize
atmospheric noise. What must be attempted is to keep the noise within tolerable limits
and we believe that we have gone a long way towards this.
Another important factor is that, by necessity, the hovercraft hull is ‘sealed unit’. Any
accidental discharges and leaks are fully contained within the hull structure,
remaining there to be pumped out an appropriate shore facility. There is no exhaust
discharge into the water as with most conventional water craft, thus eliminating the
pollution of the marine environment by oil and fuel particles, particularly prevalent
with two stroke outboard motor usage. These engines operate at a mixing range of
1:50=1part oil:50 parts gasoline where the unburned oil and fuel particles get
discharged over the lower unit of engine-basically oil injecting the environment you
navigate in. Atmospheric pollution is also considerably is less because of the inherent
fuel efficiency of the modern four stroke machinery utilized, as opposed to very large
percentage of marine propulsion units which still utilize the stroke principle. In
addition, the hovercraft is in itself a fuel efficient mode of transport, thus lessening the
pollution of the atmosphere even more. For example a fully loaded six-person
hovercraft burns less fuel per hour then a typical Jet Ski; it does not pollute the water
and does not disturb the bottom in shallow areas which many fish rely upon for food
and breeding. The lower hull of a anti fouling coating like on all common boat hulls.
Department of Mechanical Engineering
Bangalore Institute Of Technology, v.v.Puram, Bangalore 22
Working principle and some Design Concept of Hovercraft
These anti fouling paints have just one purpose-slowly come off your hull with
whatever marine lives adhere to it. On an average of 30 boat hull you have to apply all
two years a new bottom coat-besides the expenses of haul out-you will apply between
0.00373m3 -0.00568m3 of bottom paint to your hull. Bottom paint which tries to have
a very high copper contend to work effectively (30 to 75%). Copper is just not the
best stuff for our marine environment, but we do our best to supply on a continuous
basis till we find a better solution……when? If the last fish is dead?
The wake created by the passage of the hovercraft is minimal, ensuring that river bank
erosion and damage to foreshore by the waves created is virtually nil. A study in the
United Kingdom concluded the passage of hovercraft over inter tidal areas caused no
damage to sea grasses or invertebrates. It was also noted that the bird life rapidly
adjusted to the presence of the hovercraft. This has been confirmed on the Gold Coast
(Australia) where a commercial operator passed over the same area of the beach many
times a day for more then three years without any effect to the Yabby population
( Yabbies live just below the wet sand) on the actual operating launch ramp. The air
pressure exerted by the hovercraft is considerably less then the normal pressure
variations due to natural tidal movements. Commercial operators in other areas
around Australia have had similar experiences.
Last not least – Hovercraft need minimum base requirements. Hovercrafts do not
require docks, piers or dredged channels and can operate off many beach sites. Road
access to the maintenance base is desirable but not essential. Hovercraft can work in
areas and leave without the need for environmentally damaging the construction
projects to support the operation.
Department of Mechanical Engineering
Bangalore Institute Of Technology, v.v.Puram, Bangalore 23
Working principle and some Design Concept of Hovercraft
APPLICATIONS OF HOVERCRAFTS
Due to their characteristics hovercrafts have a big variety of applications, some of
which are listed below.
Passenger transport and tourism related excursions.
Commercial freight transportation.
Exploration
Search and rescue
Patrol and security
Amphibious
Fast attack
Mine counter measures
Policing and Customs.
Department of Mechanical Engineering
Bangalore Institute Of Technology, v.v.Puram, Bangalore 24
Working principle and some Design Concept of Hovercraft
Logistics
Medical Evacuation
Crash Rescue
Hydrographic survey
Commando Missions
Range patrol
CONCLUSION
A hovercraft being an expensive piece of equipment is useful in many
applications like tourism, commercial transportation over land and water,
exploration of marshy areas, patrol and security of marshy areas and
border security in deserts, amphibious assaults, immediate military attacks,
carrying out counter measures for mining areas, policing and custom
applications, medical evacuations can be carried out by a hovercraft, crash
rescues, hydrographic surveys, commando missions and range patrols can
also be done by a hovercraft.
Department of Mechanical Engineering
Bangalore Institute Of Technology, v.v.Puram, Bangalore 25
Working principle and some Design Concept of Hovercraft
Through the capital cost and maintenance cost of the hovercraft is very
high. It is useful in many applications and can be useful in many more
futuristic applications due to ease of control.
References
Websites
http://4wings.com.phtemp.com/index.html
http://rchovercraft.com/index.html
http://www.geocities.com/ronaldb66/index.html
Department of Mechanical Engineering
Bangalore Institute Of Technology, v.v.Puram, Bangalore 26
Working principle and some Design Concept of Hovercraft
Department of Mechanical Engineering
Bangalore Institute Of Technology, v.v.Puram, Bangalore 27
Working principle and some Design Concept of Hovercraft
Department of Mechanical Engineering
Bangalore Institute Of Technology, v.v.Puram, Bangalore 28
Working principle and some Design Concept of Hovercraft
Department of Mechanical Engineering
Bangalore Institute Of Technology, v.v.Puram, Bangalore 29
Working principle and some Design Concept of Hovercraft
Department of Mechanical Engineering
Bangalore Institute Of Technology, v.v.Puram, Bangalore 30
Working principle and some Design Concept of Hovercraft
Department of Mechanical Engineering
Bangalore Institute Of Technology, v.v.Puram, Bangalore 31
Working principle and some Design Concept of Hovercraft
Department of Mechanical Engineering
Bangalore Institute Of Technology, v.v.Puram, Bangalore 32
Working principle and some Design Concept of Hovercraft
Department of Mechanical Engineering
Bangalore Institute Of Technology, v.v.Puram, Bangalore 33