HP Catalog 1958 05 Short

8/13/2019 HP Catalog 1958 05 Short

1/17

HP Archive

This vintage H ew let t Packard document was preserved and d istributed bywww. hparchive.comPlease vi si t us on the web

On -line curartor: Glenn Robb


2/17

H E W L E T T - P A C K A R D C O M P A N Y PALO A L T O C A L I F O R N I A


3/17

-hp- offers complete coverage in

-hp- 150A/AR High Frequency Osci l los co pes-DC to 1 0 MCModels 150A and 150AR are deliberately designed as themost broadly useful, most convenient high quality 10 MCoscilloscopes ever built. Unique features such as the universalautomatic optimum - trace trigger, direct - reading calibratedsweeps, simplified color-coded controls and quick filter orcathode ray tube interchange-all combine to save hours ofengineering time.

Plug- in ampli f iers increase versati l i tyA variety of plug-in units (see below) provide the versatilityof dual trace or differential in put , or high amplification elimi-nating pre-amplifiers on input from most transducers. Otherimpo rtant features include brilliant, high resolution trace with-out halo or bloom, etched circuits with unitized construction,highest quality components and ultra-conservatively ratedcircuitry.

Specif icationsS w e e p R a n g e : 0.02 psec/cm to 1 5 sec/cm.C a l i b r a t i o n : 24 sweeps: 1 -2 -5 -1 0 sequence , 0.1 psec/cm to 5 sec/cm.T r i g g e r i n g : Internal , l ine vol tage or external 0.5 v or more. Pos. orP r e s e t T r i g g e r : Optimum set t ing for automat ic stable t riggering.H o r i z o n t a l A m p l i f i e r : Sweep magnification 5, 10, 50, 100 t imes. Ver-nier position control selects any 10 cm part of sweep. Externalinput pass band dc to over 500 KC. Sensitivity 200 mv/cm to1 5 v/cm.V e r t i c a l A m p l i f i e r : Pass band dc to 10 MC. Opt imum t rans i en t re -sponse and rise time less than 0.035 psec. Signal delay of 0 . 2 5psec permits leading edge of triggering signal to be viewed.A m p l i t u d e C a l i b r a ti o n : 18 calib. voltages, 1 -2-5 -10 sequence , 0.2 mvto 100 v peak-to-peak. Accuracy 3%. Approx . 1 KC square wave,rise and decay approx. 1.0 psec.

3% accuracy.neg. slope, + 30 to -30 v trigger range.

iPr ices : -hp- 150A High Frequency Osci l loscope, $1,100.00.hp 150AR Rack Moun t Osci l loscope, $1,200.

New ampl i fiers and acces so r ies

hp 1 5 2B D u a l T r a c e D i f f e r e n t i a l A m p l i f i e r .Ne w plug-in ampl i fier p roviding di fferentialinput and dual traces electronically switchedbetween A and B channels at either 100 KCor on alternate sweeps. Sensitivity range 0.05v/cm to 50 v/cm, input at tenuator wi th 9calibrated ranges in 1 2 - 5 - 10 sequence andvernier. 250.00.Data

hp 1 5 3 A Ve r y H i g h G a i n A m p l i f i e r . N e w hp 1 5 1 A H i g h G a i n A m p l if i e r . For eitherplug-in permitting -hp- 150A to be used for 150A or 150AR , high gain uni t wi th 5.0 mv/many direct measurem ents from transducer cm sensitivity, frequency response dc to I Owithout preamplification. Pass band dc to 500 MC . 1 2 calibrated ranges on 1 - 2 - 5 - 10KC, sensitivity 1 mv/cm to 1 2 5 v/cm, bal- sequence. 1 megohm input impedance wi thanced input on the 6 most sensitive ranges. 27 ppf shunt. Pass band rise time 0.035 psec.1 5 calibrated ranges in 1 2 - 5 - 10 sequence, Has 2 BN C terminals. $200.00.1 mv/cm to 50 v/cm; plus vernier. $125.00 .

subject to change wit out notice . Prices f . 0 6 . fac tory .2


4/17

qual i ty osc i l loscopes DC to 1 0 MC

-hp- 130B BR - DC to 300 K CTermed the finest low frequency oscilloscope ever offered, -hp-130B /BR combine big scope performance a nd positive de-pendability with 1mv sensitivity and the convenience of directreading, universal automatic trigger, no preamplificationfrom most transducers and simple controls.

.

Simi lar X and Y ampl i f iersModels 13 0B /B R have similar horizontal and vertical ampli-fiers with sensitivity 1 mv/cm to 1 2 5 v/cm. Inpu t circuits arebalanced on the 6 most sensitive ranges; single ended in put dcor ac coupled. 2 1 sweep times may be directly set, instrumentsweeps 1 pec /cm to 1 2 . 5 sec/cm, triggering is internally, byline power, or externally by 0.5 v or greater. Includes x 5 mag-nifier for all internal sweeps increasing fastest sweep time to0 .2 pe c /c m . -hp- 130B (cabinet) or 130BR (rack) 650.00.

-hp- 120A AR-DC to 200 K CIdeal for industrial or production line work as well as dailylab jobs, Models 12 0A A R are outstanding in both value andbig scope performance features. This all-new instrumentcovers DC to 200 KC, has the -hp- universal trigger circuitwhich optimizes signals automatically; also offers automaticsynchronization on any internal or external voltage includingline power.

Sweeps 1 p s e c / c m to 0.5 sec/cmFeatures include 1 5 calibrated sweeps in 1-2-5 sequence, sweepspeeds range 1 psec/cm to 0.5 sec/cm, times -5 sweep expan -sion on all ranges, hig h sensitivity calibrated vertical amplifiers.All pow er supplies are regulated for steady, drif t-free traces.Automatic trigger an d base line can be cut out for brig ht, clearphotography trace. Extra compact Model 120AR is only 7high. Utmost dependability, rugged construction. -hp- 1 2 0 A(cabinet) or 120AR (rack) $435.00.

in cr ease co nv enience of your 150A AR

-h p - A C - 2 IC 50: V o l t a g e D i v i d e r P r o b e .A 50:l divider wi th high 10 megohminput impedance and low 2 . 5 wf inputcapacitance. Convenient pen size formaximum handl ing ease. Probe has dur -able, at t ract ive nylon barrel , al l igator cl ipcontactor. $25.00.

.. , -h p - A C - I ISA O s c i l l o s c o p e T e s t m o b i l e . Most convenient mobile os-ci l lo>cope m ount ing. For 150A osci l losiopes but usable wi th otherinstrumtents. Rolls easily o n large 4 ubbe r-tired wheels. Extra-sturdyConstruction of tube stock, gleaming chrome throughout , T o pshelf tilts 30 in four 71 increments for better viewing. 580.00.- h p - A C - 1 1 6 A T e s t m o b i l e S t o r a g e U n i t . Extra-convenient storage fo r-lip- 151A 1 5 2 A / B , 153A oscilloscope plug-ins. Holds u p t threeextra pl ug -i ns gaurd against dust. mechanical d amage. Fits -hp- AC-115A Testrmobile (see ph ot o) : no installation nee ded 5 2 2 . 5 0 .-h p - AC-117A T e s t m o b i l e A c c e s s o r y D r a w e r . Fits in -hp- AC-116AStorage U n it convienent drawer sto rage for tools, componenrs,solder etc. Photo shows A C - 1 1 7 A installed in top rack of AC- 116AStorage Uni t 510.00.

3


5/17

-hp- Oscil lators 0.008 to 10,000,000 c p s

h p 300A

h p 3308

Hewlett-Packard now offers 1 2 high quality,fast and accurate oscillators, each an excep-tional value and each engineered to do a spe-cific job best. Each incorporates the famousRC resistance capacity circuit pioneered by-hp-. This circuit makes possible instrumentsthat are highly stable, wide range, compactand portable; instruments that are extremelysimple to operate and require no tediousre-setting or adjustment during operation.

Wave f orm analyzer 30 cps to 16 KC Variable electivity; measuring $775.00range I mv t o 500 v

Measures totalaudio 20 cps to 20 KC Inc ludes input ampl i f i e r , VTVM 4l0.00Adis tor t i on

I ns t r um en t

h p

h p 330D

P r i m a ry U s esAud io tes ts

Subsonic throu gh supersonicaudio and ul trasonic testsInterpolat ion, frequencymeasurements

Telemetry, carrier current tes ts

For FM broadcast 2o cps to KC Spec ial VU meter to meet M ~ ~ ~measurements F.C.C. require mentsFor AM , FM broadcast 2o cps to 2o K C AM detec tor a n d V U m e t e r t o 455,OOAmeasurements meet F.C.C. require ments

F requenc y R ange20 cps to 40 KC

o u t p u tI watt/24.5 v

I60 mw or IO v/500 ohms;20 v open c i rcu i t160 mw/lO v

160 mw or IO vl6OO ohms;20 v open circui t

-. P r i c e;130.00h p 200AB

5 cps to 600 KC 160.00h p 200CD

h p 200J

h p 200T

6 cps to 6 KC

250 cps to IO0 KC

275.00

350.00h p 201C H i gh qua l i t y aud i o tests 20 cps to 20 KC 3 w or 42:5 v/6OO oh ms 225.00

LOW f requency measurements 0.008 t o 1200cps '8 mw o rohmsv p-p/4000 465.00Ah p 202A

h p 202Chp- 200 Series Audio Osci l lators Servo equipment tests' I cps to 100 KC 160 mw or IO v/600 ohmsmeasurements I 300.00h p 205AG 5 wattsigh power audio tests ,gain measurements 2o cps to 2o KC 475.00A

For audio and ul t rasonicmeasurements, hp offersp o p u l a r M o d e l s 2 00 ABa n d 2 0 0 C D . B o t h h av ehighest stability and accu-rate tuning circuits. Lowimpedance operating lev-els plus superior insula-tion guarantee long yearsof t rouble-free dependa-bility. Operation is sim-ple; just three controls; no

hD 206A + 1 5 d b migh qua l i ty , h igh accuracyaudio tests 2o cps to 2o KCI 615.00A275.00475.00

h p 207Ah p 233Ah p 650A

___

490.00A5 mw/3 vA Rack mounted instruments available at $15.00 less.zero s etting necessary. -hp-200AB, 20 cps to 40 KC, 130.00. -hp- 2 0 0 C D 5cps to 600 KC, $160.00.

-hp- 2 0 7 A Sweep Oscil la torThis new audio oscillatorprovides cont inuous sin-gle-sweep frequency cov-erage from 20 cps to 2 0KC. o band swi tching isneeded; dial accuracy is470, and the inst rumentalso provides a flexible 10v/600 ohm output usablebalanced or with on e sideg r o u n d e d . F r e q u e n c y r e -sponse is k 1 . 0 d b ful l

- hp 202A, $465.00A.-hp- 6 5 0 A Test Osci l lator

Covering 10 cps to 10 M C , -hp- 650A is a highlystable, wide band inst rument for audio, super-sonic, video and rf measurements. Output is flatwi thin 1 db ful l rang e; vol tage range is 0.00003to 3 v . In addition to 600 ohm impedance, volt-age divider provided a 6 ohm impedance. Dis-tortion less than 1% to 100 KC; stability* to 100 K C . $ 4 9 0 . 0 0 A .range, distort ion and hum are less than 1%.-hp- 2 0 7 A may be swept by hand motor driventuned remotely or coupled t a recorder hp 207A,$275.00.

-hp- Distortion, Wave Form A naly zers -20 cp s to 20 K C-hp- 330B Distor t ion Analyzer

P r i c eh a r a c t e r i s t i c srequenc yR angen s t r u m e n t P r i m a r y U s es

0.1% a r e r e a d a b l eaccurately. Frequency calibration accurate within* % ful l range. Includes a 20 db amplifier, oscil-loscope terminals and precision 10 cps to 100 K Cvacuum tube voltmeter usable separately. $410.00A. A Rack mounted instruments avai lable at f l5.00 less.4


6/17

NEW -hp- 2 1 8 A Digital Delay Generator

-hp- 21 9A Dual Tr igger U nitThis plug-in drawer for -hp- 218A supplies trigger pulses ofpositive polarity, 50 volts, 0.1 psec rise time from a 50 ohmsource. Pulse A occurs at To or T, as selected by a switch;Pulse B is triggered at T,. -hp- 219A, l O o . OO .

-hp- 2196 Dual Pulse UnitThis plug-in drawer for -hp- 218A produces two high-powerpulses which are continuously adjustable in width, 0.2 to 5psec and in am plitude from 0 to 50 volts, positive or negativepolarity. Th e leadin g edge of these pulses can be set to occurat the beginning or end of the selected time interval. Bothpulses are brough t out to separate fron t panel jacks but may beswitched to a common jack with no change in level or outputimpedance. -hp- 219B, 450.00.

-hp- 219C Digital Pulse Duration UnitThis plug-in drawer for -hp- 218A produces a high poweroutpu t pulse whose delay an d dura tion are digitally controlled.Th e pulse is available in both polarities simultaneously, an d iscontinually adjustable in amplitude up to 20 volts from a 90ohm source. It may also be obtained from a directly coupled500 ohm source with an amp litude of 100 volts. -hp- 219C,350.00.

Independently adjustable t imeintervals or pulse delayst 0 . 1 psec t ime in terval accuracyCrystal osci l lator t ime baseRegulated power supplies

Model 218A Digital Delay Generator is a totally new instru-ment applicable to many types of timing measurements in-cluding calibrating the range determining circuits of radarreceivers, etc. The generator is built to rigid standards and issuitable for military use. It provides two precision time inter-vals or pulse delays, either of which are independently adjust-able from 1 to 10,000 microseconds in 1 microsecond steps.These time intervals are accurate to within 0.1 microsecondt o . o o l % of th e selected value, and may be initiated f rom aninternal multi-vibrator, 10 cps to 10 KC, or from an externalrate generator, 0 cps to 10 KC. Total jitter does not exceed0.02 microseconds in either case. T he in strum ent also providesa 50 volt synchronizing output pulse at the b eginning or endof a time interval, and a 1 microsecond timing comb outputat the front panel.

No count ambiguityA unique feature of the new -hp- 218A is its time base, apulsed crystal controlled oscillator. The oscillator starts at Toand stops at the last output pulse. This eliminates the plus-or-min us-1 count ambiguity of many counter circuits in suchapplication.Model 218A is a completely self-contained instrument, re-quiring only on e or more -hp- 219 series plug-ins to performa broad variety of time and delay generation measurements.Simplicity and flexibility are increased by the large variety ofinput and ou tput connections brought to the front panel. T heinstrument is particularly compact and w ell-desig ned; etchedcircuits and the use of plug-ins materially increase circuit ac-cessibility.The instruments power supplies are fully regulated to avoideffects of line voltage variations. It s available as -hp- 218A,cabinet mount, or 218AR, rack mount. -hp- 218A AR,$2,000.00.

-hp- Square Wave and Pulse Generators-hp- 212A Pulse Generator -h p- 211A Square Wave Generator

Provides continuously variable, highpower fast pulses of superior waveform. Combines broad general useful -ness wi th 0.02 psec rise and decaytime to meet requirements of radar,T V and nuclear work. Pulse lengthvariable 0.07 to 10 ~ e c : in imum

Versat ile, wide range inst rum ent for test ingoscilloscopes, networks, video and audio ampl i fier performance, modulat ing signal generators and measuring time constants. Offersimple control of electronic switches; is alsoconvenient for indicat ing phase shi ft , freisient effects. Tw o separate outputs ( a ) 7 vol

7 5 ohm c ircui t fo r TV work; (b ) 5 5 volt 600 ohm output for h ighlevel wor k. Both have full amplitu de variation. Instrument opera tef ree-running or external ly synchronized wi th posi t ive going pulse osine wave of vol ts minimum ampli tude. 265.00.

overshoot; 50 watt peak power (50 v to 50 ohms load ) . Low imped-ance means accurate pulses can be delivered at a distance from theinstrument. Repetition rate variable 50 to 5,000 pps; controlled inter-nally or externally. Synchronizing pulse available in advance of, orfol lowing output pulse. 565.00 (cab ine t ) , S50.00 ( rack mount ) .

quency reseowe, trar:

5


7/17

-hp- Vacuum Tube Vol tmeters 1 0 to 700 000 000 c p s

Fr e q u e n c y V o l t a g e InputPr imary Uses Range Range Impe danc e

measurements ranges

Ins t rumenth p 400AB General purpose ac c p s to KC 0.003 t o 300 v

NEW -hp- 400L Logar ithmic Voltmeter N EW -hp- 42 5 A Mic rovol t -Ammeter

Price

N e w -hp- 400L, 10 cps to 4 MC, features a 5"t rue log voltage scale plus a 1 2 db linear decibelscale. The log voltage scale plus long scale lengthprovides a voltmeter of maximum readability andan accuracy which is a constant percentage ofjhe reading. Accuracy is 25% of read ing ori 1% of full scale, whichever is more accurate,to 500 KC; * 55% full frequency range Voltage

New, high sensitivity, high stability microvoltmeter reading full scale voltages of 10 pv to1 v in 11 ranges. Also reads currents of 10 ppato 3 ma in 18 step, 1 - 3 -1 0 sequence. Accuracy+ 3 on all ranges. Drift less than 2 pv referredto input terminals Inpu t impedance 1 megohmi - 3 on al l ranges Inst rumen t can also beused as a 100 db ampl i fier providing up to 1 voutput from signals as smal l as 10 Pv. Amplifier

-hp- 425A

range 0 . 3 mv to 300 v in 1 2 steps. a c r eje ct io n i s a t le as t d b a t 0 . 2 ; ~ ~nd 60 db a t 60 cps. InAaddi-tion to enginee ring uses ideal fo r physics, chemistry applicationsincluding grid or photomultiplier tube currents, ionization levels,thermocouple potentials and voltaic currents. Also measures v i nliving cells, nerves, seeds, plants. Inclu des probe. $500.00.Generous overlap is insured by a 1o db range switch plus a 12 dbmirror backed for maximum accuracy. Also may be used as a stablescale length. High stability, l o megohm input impedance. Meter is

Read pv , @pa; 100 d bchemica l

ampl i f i e r ; medica l , dc vo l tages as I O p v t o I v I megohm 500.00bio log ica l , phys ica l , 100 d b a m p l if i e r I I ranges 3%

amplifier. $325.00.

- hp - 40 0D VacuumTubeVol tmeterBest -hp- vol tmeter ever bui l tCovers all frequencies 10 cps to4 MC. Extremely sensitive, widerange, accurate within 270 to 1MC, measures 0.1 mv to 300 v.Direct reading in dbm. 10 meg-o h m i n p u t i m p e d a n c e i n s u re snegligible loading o n circuits un-

der test. New amplifier circuit with mid-range feed-back assures utmost stability, freedom from changedue to external conditions. $225.00.

Fe a t u r e s P r i c e

-hp- 410B Vacuum TubeVoltmeter

All-purpose test inst ru-ment, range 20 cps to700 M C . Also serves asd cVT VM wi th over 100megohms impedance, orohmmeter for measure-ments 0.2 ohms to 500megohms. Input capac-ity 1.5 ppf , 10 megohmsi n p u t i m p e d a n c e ; e m -ploys radical diode probewhich virtually eliminates circuit loading. Indus-

try's most versatile precision voltmeter. 245.00.

h p 453A Capac i t i ve Vol tage D iv id erh p 454A Capac i t i ve Vol tage D iv iderh p 455A Probe Coaxial 7' onnector

For h p 4108 VTVM only. Division 1 O O : l 25.00For h p 400D and 400H only. Division 1 O O : l 30.00

35.00or h p 410B VTVM. Measures vol tage s between conducto rand sheath of 50 ohm transmission line

Ii de r ange acmeasurementsI Hig h sens it i v ityh p 400D

For h p 400 series VTVM. For measurement of currentIh p 470A to F Shunt Resistors

0.001 to 300 v IO megohmsig h accuracy widerange acmeasurementsh p 400H lo ps t o 4 M C 12 range s 15 p p f shunt 325'00

470A 15.00470B-F 10.00

h p 400L Log vo l tages, l i near cps to MC mv t o 300 v IO megohmsd b measurements 12 ranges 15 pp f shunt 325.00

ac-IO me go hms / 245.00Iudio, rf , VHF dc; ac-20 0.1 t o 300 v dc--122 megohms;measurements; dcvoltages: resistances c p s to MC r a n g e s 1.5 ppfIh p 410B

-hp- 40 0 H Vacuum Tube Vol tmeterNeed extreme accuracy of 1 ? -hp- 400H covers 10 cps to 4 MC,has 5" meter wi th mirror scale, measures vol tages 0.1 mv to 300 v .10 megohm resistance minimizes circuit loading, amplifier with 56 dbfeedback insures lasting stability. Dire ct reading in db or v. Extremelyhigh qual i ty throughout . $325.00. .

-hp- acc ess o ries in cr ease usefulness of your vol tm eters

h p 452-95A Adapter I Connects h p 452A to h p 4108 VTVM pr obe I 10.00

25.00or h p 410B VTVM, Mea sur esvolts a t o p e n e n d of50 ohm transmission lineh p 458A Probe Coaxial N Connectors25.00or h p 410B VTVM. For measuring high dc vol tagessafely. Mult ipl ies 1 : l O Oh p 459A DC Resist ive Vol tage Mult ipl ier


8/17

NEW -hp- 5 2 4 D Precisio n Electron ic Counter

Extends range of 524to measure 10,000per iods

5 PLUG-IN UNITS INCREASEFLEXIBILITY USEFULNESS

FOR MANY MEASUREMENTS

Greater accuracymeasurementin pe rio d 225.00

hp 525A F r e q u en c y C o n -v e r t e r . Extends 524Ds di -rect reading range to cover10 cps to 100 MC with noloss in accuracy. Providesadditional amplification toincrease video sensitivity to 0.1 v through 524 Dsbasic 10 cps to 10.1 MC range. $250.00.

vides high sensitivity for low level work. @56.00.hp 526A V i d e o A m p l i f i e r .Increases 524D sensitivityto 10 mv for low powerfrequency measurement 10cps t o 10 .1 MC. Accuracysame as counter; minimuminput 10 mil l ivol ts rms. $175.00 .hp 526B T i m e I n t e r v a l U n i t .Permits 524D to measurei n t e r v a l 1 . 0 p s ec t o 1 0 0days with accuracy of 0.1psec * 0 . 0 0 0 1 ~ . eads insec, msec or psec. Trigger-ing from separate stop or start on pos. or neg.going waves. Trigger adjustable -192 to -k 192vol ts. $175.00.hp 526C P e r i o d M u l t i p l i e r .Permits 524D to measureperiod over 100, 1,000 or10,000 cycles of unknown,thus providing the greateraccuracy of mid-range fre-quency readings. Front panel switch selects desiredperiod. $225.00.

New stabi l i ty-5 parts in IO er weekNew convenience - 8 vertical readout unitsDirect, instantaneous, automa tic readingsCovers frequencies 1 0 ps to 220 M CMeasures t ime interval 1 psec to 1 daysMeasures period 0 cps to 1 0 KCResolution 0.1 microsecondsNo calculation or complex setupEasily used by non-technical personnelHigh, sensitivity, impedance, re liability

New crystal oscillator stability of 5 parts in l o8 per week plus the added con-venience of uni form vertical neon readout units-these are significant advance sincorporated into new -hp- 524D Electronic Counter, at no increase in priceover -hp-524B.The new 524D permits you to buy only the basic counting facilities you neednow-later on add inexpensive plug-ins to triple and quadrup le the usefulnessof your counter,The basic -hp- 524D reads frequency 10 cps to 10 MC over 5 selected periods.Display time is variable, counts are automatically reset, action is repetitive, read-ings are direct without calculation or interpolation; an automatic illuminateddecimal poin t is included.The instrument is of highest quality throughout and employs a military designapproach, -hp- 524D lessmount) .

I n s t r u m e n t P r i m a r y U se s

Ih p 524D

measurementh p 525AFrequency

Conver terh p 525BFrequencyConver terh p 526AVideo..Ampl i f i e rh p . 526BTimeInterva l Unih p 526CPer iodMul t ip l i e r

Extends 524 ranget o IO0 MC; increasebasic sensitivity

Extends 524 rangef r o m 100 to 220 MC :high SensitivityIncreases 524Sensi tiv i ty t oI O mi l l i vo l ts

Measures interval Ipsec to 100 days

Period measurement

plug-ins, 2,150.00 (cabinet) ; 2,125.00 (rack

Fr e q u e n c y R a n g e C h a r a c t e r i s t i c s P r i c eDi rec t reading, no in ter -

D i rec t reading, noi n terpo la t ion; s tab i l i t yI 5/108 per w kAccuracy cps+ stabi l i ty; 0.1 v rms 250.00I min. inputIO c ps t o 100 M C Accuracy I cpsmin. i nputsta bil ity ; 0.2 v rms 250.00

175.00Accuracy same as basiccounter: IO mv rmsI min. inputI O cps t o 10.1 M C175.00ccurate 0.1 pseco.ooo Ipsec to IO sec I -

.Rack moun ted instrument avai lable for $25.00 less.

7


9/17

-hp- 5 4 0 A Transfer Oscil lator

Just two -hp- instruments-Model 540A Trans fer Oscillatorand a 524 series electronic counter, (with plug-ins) are allthe equipment you need to measure unknown frequencies upto 1 2 KM C swiftly and accurately.This simple, two instrument setup is particularly useful forquick C W an d A M frequency measurement, FM center fre-quency and deviation checks, frequency of hig h-noi se signalsand pulsed signals. Overall accuracy is better than 10 timesthat of th e best microwave wavemeters; and on clean CWsignals, is about 1/1,000,000.

Simple operationWhen approximate frequency is known, the 540A is tuneduntil a harmonic beats with the unknown. The multiplying

Measure frequency t o 12 K M Cquickly, easily, with electroniccounter accuracy. Av oid guess-work, end "trial and error," elimi-nate expensive setups. Measureon pulsed, AM, FM, CW andnoisy circuits.

noted, and the 540A frequency measured on the 524.acto r isThe 524 reading, times the multiplying factor, is theunknown.Brief Specif ications

Oscil lator Freq. Range: 100 to 2 2 0 M CHarmonic Freq. Range: Up to 1 2 K M CStabi l i ty : B e t t e r t h a n 0 . 0 0 2 ~ / m i n u t eO ut pu t : 2 volts into 5 0 ohmsAt tenuator Range: 20 to 80 db into 50 ohmsAmpl i f ie r Ga in : 40 db max, 1 v outputOscilloscope: 100 cps to 200 KC; vert.Price: $615.00

SWR 1.5 at 1 K M C

sens. 5 mv rms/inch

hp 5 6 0 A Digi tal Reco rd erContinuous digital reco rd fo r frequencycountersDirec t reading, simple hookupFive 11 digi t l ines secondAnalog output for recorderExpanded scale; ful l scale IO7Accuracy identical to counter used

.

N o intermediate equipment is needed between -hp- 560A andits Counter. In direct hookup, completely self-contained -hp-560A provides a complete record of all types of test data, plus,throu gh an analog outpu t, a convenient graphic record of verysmall data variations.Th e analog outpu t is a voltage or current proportional to thenumber represented by any 3 consecutive digits of recordeddata. The 560A permits expanded strip chart recording andthe chart cannot be driven off scale since range variation fo rthe 3-digit scale is 0 to 999. Wider variation merely causes arepetition of the 0 to 999 sequence.Prin t capacity is five, ll -d ig it lines/second; secondary orcoding data may be entered simultaneously with primary data.

Brief Specif icationsAccuracy: Identical to counter usedPrint ing Rate: 5 lines/sec maximumD ig i t C apac i t y : Up to 11 per lineDriving Source: Parallel entry staircase voltages, descending135 to 5 5 v, 0 to 9A n a l o g O u t p t : Proportional to any 3 consecutive digits;max. amplitude 1 ma or 100 mvPrint Command Signal: 10 psec minimum, pos. or neg.,Price: (11-digit, cabinet model), $1,390.0015 v/pulse(11-digit, rack mou nt), $1,375.00


10/17

Other =hp- Frequenc y Measurin g and Monitor ing Equipm ent

Ins t rument-hp- 500B/C Frequency MetersDirectly measures frequency ofvoltages 3 cps to 100 KC; ex-panded scale al lows any 10%or 30 % of range to be meas-ured full scale. Sensitivity 0.2 vrms (sine waves) 1 v peak forpulses. Inpu t impedance 1 meg-ohm with 40 ppf shunt ; accu-racy independent of line volt-age changes. Also available as -hp- 50 0C cal ibratedfor direct reading in rpm. -hp- 500B/C, $285.00.

P r i m a r y U s es F r e q u en c y Range

h p 500BElectronicFrequencyM e t e r

C h a r a c t e r i s t i c sStabi l i t y 1/1,000,003 (short.t ime) . S ine or rec tangularou t pu t . M a rk e r p i ps

Aura l dev ia t ion +3 KC.v id e o d ev ia ti on i 3 C :accuracy i 5 0 0 c ps app rox

3 c p s t o 100 K Capid f requencymeasurements

P r i c e

615.00L

h p 500CI nd i c a t o r

Rpm measurements 180 t o 6,000,000 rpm

h p 506AO p t i c a lTachometerPickup300 t o 300,000 rp mps and rp mmeasurement

ScalerCapac i ty countsi n 2 decades.pulses 10,000,000 ppscount ing ra te

For count ing h igh- ra te

h p 521CIndust r ia lElectronicCounterMeasure frequency,speed cps to 120 KC

hp 523BElectronicCounterF r e qu e n c y p e r i o dt ime in terva l IO c p s t o 1 . 1 M C

100 K C , I O KC,I K C , IO0 cps,I IO cpsFrequency, t imemeasurementsh p 100DSecondaryStandardh p 335ER Aura l and v isua l car r iermoni tor ing: b lack andwhi te or co lor Channels 2 to 83 2,050.00

9 ranges k 2 Y o accuracy.I npu t 0.2 t o 250 vol ts 285.00

S i m i la r t o 500B b u tc a l ib r a t e d i n r p m 285.00-hp- 5 0 6A Opt ica lTachomeeomete P c kup

Versatile, flexible light sourceP ho to t ube a nd l i g h tsource; output I v rms 125.00

100.00and pickup for use as a trans-d u c e r w i t h - h p - 5 2 1 A / C ,500B/C, etc. Measure s 300 to3 0 0 , 0 0 0 r p m ( b e yo n d w i t h

h p 508ATachometer Shaft speed measurement 15 t o 40,000 r p mGeneratorOutput 60 cyclesper revo lu t ion

h p 508BTachometer Shaft speed measurement 15 t o 40,000 r p mGenerator 1oo.uou t p u t 100 cyclesper revo lu t ionmplified outpu t) ; normal out-put at least 1 v rms into 1megohm or greater impedance.Light source 21 cp 6 v bulb;Type 1P41 phototube, photo-tube bias 70 to 90 v dc (sup-pl ied from -hp- 500B/C, 521A / C ) . -hp- 506A, $125.00.

~

h p 508CTachometer Shaft speed measurement 15 t o 40,000 r p mGene ra t o r ioo.00u t p u t 120 cyclespe r r ev o l u ti on

h p 508DTachometer Shaft speed measurement 15 t o 40,000 r p mGenerator 100.00ut pu t 360 cyclesper revo lu t ion

lO0 : I d i v i de r f o r ope ra t i onof low speed sca lers 6 I5.OOb-hp- 5 0 8 A - D TachometerGene ratio s Di rec t read ing, accuratewi th in e l count i -O . l%,4 place reg is t ra t ion 475.00R o t a t i n g s p e e d t r a n s d u c e r sused with electronic countersor frequency meters for simple,a cc ur at e m e a s u r e m e n t s f r o m1 5 to 40,000 rpm (o r beyond Di rec t rea ding, accuracywi th in k coun t i O . 0 1 yo,5 place reg is t ra t ion 650.00with am pl i fier)--hp- 508A pro-v i d e s 6 0 o u t p u t p u l s e s p e rshaft revolut ion; -hp- 508B, C, D provide 100,

120 and 360 pulses/rev respectively. Ou tpu t volt-age increases linearly with shaft speed to 5 ,0 0 0pps. Running torqu e approx. 0.15 in. 0 2 . ; peakstart ing torque approx. 4 in. 02. -hp- 508A, B, Cor D 100.00.

h p 5228Electronic Frequency, period ime IO c p s t o I20 K CCounter interv al measurements 915.00bi rec t rea d ing, accuracyi coun t i - 0. 001oDi rec t rea ding, accuracy+ I count i 2 / 1 , 0 0 0 , 0 0 0 1,245.00

R a c k m oun t ed i nst r umen t av a i l ab l e f o r $15.00 less.-hp- 521 A/C Industria l Counters

Low cost, simple operation, al-most limitless uses characterize-hp-521A/C Indust rial Counters.-hp- 521A measures speed, rpm,rps, frequency, random eventsper unit of time ; with prop ertransducers also measures weight,pressure, temperature, accelera-tion, etc. -hp- 521A reads directin cps, rpm and rp s; display is variable 0.1 to 15 sec-onds or hold; 60 cps check circuit confirms accu-racy of readings; three accessory power supplies in-clude -150 v dc, 4- 300 v dc and 6.3 v ac. Fre-quency range 1 cps to 120 KC, accuracy e 1 countaccuracy of built-in 60 cps timing frequency (u su -ally * 0. 1% ); i nput min . 0 .2 v rms; i nput a t tenu-ator adjusts sensitivity 0.2 to 100 v rms, input im-pedance 1 megohm with 50 ppf shunt , gate time 0.1and 1 sec, also Manual Gate. -hp- 521C same as

521A except has gre ater accuracy, crystal controlledtime base and 5-place (instead of 4-place) registra-tion with count capacity of 99 999. -hp- 521C,$650.00. -hp- 521A, $475.00.

-hp- 5226 Electronic CounterCompact, low cost, versatile instrument for frequency, period ort ime measurements. Measures frequency 10 cps to 120 KC, t imeinterval 10 psec to lo6 sec. Reads direct in cps, KC, seconds ormilliseconds. Count automatically reset, action repetitive. Stabilityof time base 5/1,000,000 per week. Easily used by untrained per-sonnel. High quality, completely self-contained, bright, clear nu-merals; ideal indust rial as wel l as lab inst rument . 915.00A.

-hp- 5236 Electronic CounterRevolutionary all-purpose counter measures frequency 10cps to 1.1M C ,time interval 3 psec to 27.8 hours, period 0 00001 cps to 10 KC. Sta-bility 2/1 000 000 er week. Results displayed in sec, msec, psec orKC; au tomat i cdecim al . D isplay t ime variable 0 .1 sec to 5 sec or in-definitely. Accuracy count plus crystal stability, 5 gate t imes.Usable wi th 100 KC primary standard. High qual i ty, completely sel f-contained, bright numerals, controls color-coded for simpler use bynon-technical personnel. Pulse output for Z-axis oscilloscope modula-tion. $1,245.00.

9


11/17

Microwave Impedance Measur ing EquipmentI n s t r u m e n thp- 416ARatio Meter

Automatically com-bines forward and

P r i m a ry U s es F requenc y R ange C ha ra c t e r i s t i c s P r i c e

variations. Contains rf power m onitor indicatingproper power level. Rear terminal signal availableto operate oscilloscope or recorder. Suitable for sin-gle and swept frequency operat ion. $45 0.00 A.

hp 416ARatio Meterh p 417A

vhf Detec tor-hp- 415B Standing

Wave IndicatorFor all waveguide and coaxialslotted sections. Gives readingsi n S W R or d b . S i n g l e f r e -quency operation; 315 to 2,000cps. Low noise level, 0.1 pv(f ul l scale) sensitivity, 60 db.calib. attenuator. 200.00.

Reflect ioneasurementsoef f i c ientvhf br idg e detec tor

( f o r h p 803A)

Continuous swept frequencyApprox . 5 p v

sensi t iv i ty

,Oo0 k 4 0 CPS p res en ta t ion ; ac cu rac y i . 3 ~ ~ 0 . 0 0 ~350.00O to 500 M C

-hp- 803A VHF BridgeProvides direct impedance meas-urements in vhf range, 2 to2 ,000 ohms, -90" t o +9 0"phase angle. Wide frequencyrange 5 2 to 500 MC; makesmeasurements down to 5 M Cand up to 1,000 MC, Fast , sim-ple to use. $600.00.

h p 803Avhf Br idge

-hp- 417A VHF Detector

Measurement of vhf 2 t o 2,000 ohms impedan ceimpedance, SWR 52 to M C -90 t o +90 phase ang le 6oo'oo

Super- regenera t i ve (AM) re-ceiver covering all frequenciesfrom 10 to 500 MC in 5 bands.Designed for use with -hp-803A Bridge. 5 pv sensitivityf u l l range . S ingl e f requencycontrol, reads direct in MC.$350.00 .

hp 806BCoax ia l S lo t tedSectionhp 8098Universal ProbeC ar r i age

3,000 to 12,000 M C For Typelexible Connectorsables 200.00

G, J H and Waveguide Sections A c c ep t s 4428, 44A probes 160.00Suppor ts 8068 sect ion, also

Low a s s Filters vol tages f rom A- 700 M C C-2,200 MC $ 40.00h p 360A-D El iminates harmo nic Cut-off frequenciesI uhf systems B-I, 00 M C D -4 ,100 M CI IIto 70 d b a t t n .Max. sen si t iv i ty 0.1 p v 2oo'ooStanding Wa ve SWR ind icator or 315 t o 2,000 cps. Normalh p 415BI nd i c a t o r f req. 1,000 cpsIul l i nd icatorI

For Type N C onnectorsf lexible cablesSection IF or r i g i d '/8 RG44/U line 475.00Iame as aboveoaxial Slotted Same as aboveSectionh p 805B

Accepts Untuned Probe 446A

Iupports P, K a n d R 815BWave guide S lo t ted Sect ionsI

h p 814BUniversal ProbeC ar r i ageRack mounted instruments 15.00 less.

-hp- 360 Lo w Pass Fi lters -hp- 80 5A /B S lo tted L ines

Isolating filters which speed microwavemeasurements by eliminating harmonics,permitting transmission at single, knownfrequency only. Particularly necessary inslotted line, filter characteristic, receiverresponse , s imi l a r measurement s . Ta bl eabove gives cut-off frequency; insertionloss not over 3 db; nominal impedance 50ohms. -hp- 360A, B, C or D, $40.00.

Exclusive -hp- "parallel-plane" design in-sures utmost mechanical rigidity, less leak-age, greater accuracy, low S WR of 1.02 or1 .04 (depending on model ) . Range 500MC to 4 KMC, reads in cm and mm to 0.1mm. -hp- 805A, for 50 ohm Type N use,hp 805B, f 46.3 ohm RG 44/U stubsupported 0.D. coax. hp 805A/B,$475.00 .

-hp- 809B 814B Universal Probe Carr iageshp 809B

Q u i c k , e a s yw a v e g u i d e i n t e r c h a n g e

Models 809B and 814B are precision built mechanical assembliesoperating, respectively, with hp 810B and 815B series slot tedsections.Combinat ion of the 809B carriage and 810B slotted sections covers2.6 to 18.0 KM C. Com binat ion of 814B carriage and 815B seriessections covers 12.4 to 40.0 K MC .On either carriage, waveguides can be interchanged in seconds forreal savings on engineering t ime. Only one p robe is required fo r eachcarriage to cover ful l frequency range. Manufacture is of highestquality to assure positive mechanical positionin g of intercha ngeab lewaveguides and precise installation of mating -hp- probes (seep a g e 1 2 ) . -hp- 809B has a vernier scale reading to 0.1 mm and isequipped for dial gauge mount ing. -hp- 814B has a cylindrical dialwhich may be read directly to 0.1 mm and interpolated at 0.01 mm.hp 810B S l o t t e d S e c t io n s . hp 810B, for moun t ing in 809B carriage,is a flanged, waveguide section with accurately machined slot. Slotis tapered at ends to minimize reflection. Available in 5 waveguidebands, 3.95 through 18.0 KMC.*hp 58I0A. Complete slotted section assembly including probe car-riage. In ~ C L O.95 KMC (S-b and ) size only.*

-hp- 815B S l o t t e d S e c ti o n s . For moun t ing in 814 B carriage. Avai lableP, K and R bands, 12.4 to 40.0 KM C. To insure positive positioningwhen mounting in carriage, these sections seat on two eccentric rods.Rods are factory-adjusted so longitudinal plane of guide is alwaysparallel to probe travel.*hp 814B *For pr i ces , see tab le pa ge 12.

I O


12/17

N EW Microw ave Pow er Measur ing Equipment

METER

Circui t ry , hp 434A

-hp- 430C Mic rowavePower Meter

No computat ions Provides in-stantaneous, automatic powerreadings direct in dbm or mwa t a l l f requenci es for whichthere a re su i t ab l e bo lometerm o u n t s . F o r C W m e as u r e-ments, uses either 1/100 amp.fuse or Sperry 821 barretter.Also measures C W or pulsedpower with negative coefficientthermistor. Provides up to 16ma bias cur rent . Operates wi th al l mounts in adja-cent table. Range 0.02 to 10 mw. 250.00.-hp- 4778 Coaxial Thermistor

MountFor frequency range 10 MCto 10 KMC. SW R less than1 . 5 . Thermistor element i s200 ohm negat ive. No tun-ing required; not suscept-ible to burnout . 75.00 ( i n -cluding thermistor).

-hp- 76 4D -7 67 D Dua l D i rec tiona lCouplers

Ne w high di rectivi tydual coaxial couplersm a k e r e f l e c t o m e t e rmeasurements practi-cal in vhf and uhfcoax systems. Flat re-sponse , h igh powercapacity, low insertion loss. Four models, covering216 to 4,000 MC collectively. $125.00.

-hp- 4 3 4 A Calor imetr ic Power MeterJust connect and read powers I O mw t o I O watts Covers dc t oI O KMC. No barretter or thermistor needed. No external termi-nations or plumbing. Measures CW or pulsed power. Two simplecontrols; no technical ski l l required.Ne w -hp- 434A Calorimetric Power Meter is, factually, the fastest, easiest wayyet devised to measure powers accurately from 10 milliwatts to 10 watts, dc to10 kilomegacycles.With the 434A, measurement is literally as simple as connecting to the 50ohm, type N front panel terminal and reading power directly, Thus the instru-ment is particularly suited for use by nontechnical people.

Compact, self-contained-hp- 434A fills the range between bolometer microwave power meters (suchas the popular -hp- 430C, below) and conventional calorimeters for pow ersabove 10 watts. But unlike previous cumbersome equipment suggested for itsrange, the new -hp- 434A is compact, moderate in cost, completely self-con-tained, and needs no detectors or external plumbing whatsoever.

Brief Specif icationsInput Power Range: 7 ranges; fu ll scale readings 0.01 to 10 wattsFrequency Range: dc to 10 K M Cdc Input Impedance: 50 ohms 5 ohms at in put jackI npu t SWR: Less than 1.5 full rangeMeter Response (full scale): Approx. 10 sec (high range)Approx. 2 sec (lower ranges)Controls: Zero Set, Meter RangeAccuracy: Within 5 of full scalePrice: 1,115.00 (cabinet); $1,100.00 (rack mount)Instrument Primary Uses

MeasurementM icrowave of r f powerh p 434A MeasurementC a l o r i m e t r i cPower Meter of r f power

Tunable of r f powerBolometer Moun t (wi th 430B/C)Universal of rf power

Measurementof r f power(wi t h 430C)Thermistor Mount Ih p 4778Coax ia lIMeasurementof r f power

h p 485W av egu i deI Detec tor MountMeasurementof r f powerI

h p 4878W av egu i deThermistor Mounth p 764D Reflectometer and rfpower measurementsi rec t iona l ICoupler

power measurements

power measur&h p 767D Dua lD i rec t iona lCoupler

Ref lectometer and r fpower measurements

Price

I115.00Ii r ec t r ead i ng , nobarretters, thermistorsor term inat ions ;C W . pu l s eddc to KM C I IMatches 0 ohmZOO ohms1,000 to 4 ,000 M C to 100 or 225.00.

Io to MC No tun ing requi redSWR less than 1.25 85'00

75.00IFul l covera ge See Table

Ful l coverage, no See Tableexcept K487B 2.0 I p a g etuning, 1.5 SWR,950 to 26,500 MC I 125.00Coup l ing a t tenuat ion '20 db, d i re c t i v i ty16 to 450 M C 3 0 d b

125.00Ioupl ing a t tenuat ion*20 db , d i r ec t i v it y50 to 945 M C 3 0 d bCoupl ing a t tenuat ion*940 to 1,975 M C 20 db , di re ct iv i t y 125.0026 d bCoupl ing attenuation:1,900 to 4,000 M C 20 db , dir ect ivi ty 125.0026 db

*Power hand l ing cap aci ty a l l 764/767 series couplers 50 w a tt s C W , I O Kw peak.


13/17

-hp - Wav egu id e Test Equ ip m ent -2.6 to 40.0 KMCBasic, low-cost elements offer utmost f lexibil i ty for assembly of exact instrumentat ion required. Each unitcovers ent i re range of i t s waveguide size. Careful engineering, simple, sturdy mechanical design, highestquality manufacture insures accurate, mult i-purpose operat ion.

Mounts in 809B C ar r i age .F o r use w i th bar re t ter o r c rysta l.Includes Thermistor, instal led.F o r use w i th ba r re t t e r only.**J530A 5.85 to 8.2 KM C, $120; J530B, 5.20 t o 7.05 KM C , $150.

*Complete assembly inc lu d ing car r iage.Includes barretter; checked for square law characterist ics.

N EW -hp- 3 8 2 A Prec is ionAttenuators

P r e v i o u s ly o f f e r e dfor frequencies 3.95through 18.0 KM C,p o p u l a r -hp- 382Aser i es prec i s ion a t -t e n u a t o r s a r e n o wavai lable in K andR bands, 18.0 to40 .0 KMC. K , R band attenuators areof new, space-savingdesign (see photo). Direct reading, one-control tuning, high pow er han dl ing capaci ty.At tenuat ion 0 to 50 db ful l range, independ-ent of frequency. Phase shift constant witha t t e n u a t i o n . F o r p r i c e s G, J, H, X a n dP382 A, see table above. -hp-K382A, $425.00.-he- R382A, $450.00

-hp- 281A Waveguide -Coa xAdaptersFor convenient transi-t io n b e t w e e n w a v e -g u i d e a n d c o a x s y s -tems Each unit coversa full waveguide rangew i t h S W R l es s t h a n1 . 2 5 . T y p e N c o a xp l u g , A N w a v e g u id eflange. For S, G, J , Ha n d X b a n d s . 2 . 6 t o12.4 KMC. 25.00 to $50.00.

-hp-48 7B Thermis to r Mounts

ged construction, high temperature coefficientthermistors vi rtual ly e l iminate burnout . ForG, J, H, X and K bands, 3.95 to 26.5 KMC.$75.00 to $95.00.

-hp- 8 7 0 A S l ide ScrewTuners

For flattening waveguide systems, matching,etc. Probe position and penetration adjusts toset up SWR cancel l ing exist ing SWR. Pre-cision lead screw or micrometer varies probeinser t i on ; vern i er ad jus t s p robe pos i t i on .Corrects SWRs of 20 with accuracy of 1.02SWR . For S, G, J, H, X, P, K , R bands, 2.6to 40.0 KMC. $125.00 to $225.00.

- hp- 420 A /B Cr ys ta lDetectors

Employs a silicon crystal to detect rf signalsin Type N coaxial l ines. Covers frequen&s10 MC to 1 2 . 5 KMC , sensi t ivi ty a pprox. 0.01v / 0 . 1 m w , f r e q u e n c y r e sp o n s e 3 d b f u l lr a n g e . U s e s m o d i f ie d 1 N 2 6 c r y s t al , m a x .SWR 3 50.00 e a c h . A l s o a v a i l a b l e i nmatched pairs as -hp- 420B, $150.00 pair.-hp- 44 4A /446A Un tuned

Probes-bp- 444A is modifiedcrystal (1N76 o r 1 N 2 6p l u s s m a l l a n t e n n a i nc o n v e n i e n t h o u s i n g .Probe penetrat ion easi lyvariable; may be lockedi n p o s i t i o n . No t u n i n gneeded; sensitivity supe-rior to most elaboratesingle or double tunedprobes. Range 2,;4 to 18K M C ; f it s % b o r e .N e w -hp- 4 4 6 4 for -hp- 814 Probe Carriage,similar but covers P, K and R bands, 1 2.4 to40 .0 KMC. -hp- 444A, $35 .00 . -hp- 446A,$145.00.

I2


14/17

NEW -hp- Noise Measu r ing Equipm ent

-hp- 347A WaveguideNoise Source

These new devices, Argon gas discharge tubes acrossa waveguide sect ion provide uniform 15.2 (15.25in S band) db excess noise level ful l range wi thmaximum S W R of 1 . 2 even when noise source iscold. N o temperature correction required. Availablefor S through P band, 2.60 to 18.0 KMC , (S, Gbands) , 190.00; (J, H , X and P bands) , 180.00.

- hp - 345A IF Noise SourceTemperature-limited diode noise sources for IFamplifier noise measurement. Matches 50, 100, 200or 400 ohms impedance. Center frequency either30 or 60 MC . Noise level depends on cathode cur-rent, controlled and metered by -hp- 340A. -hp-345A, $75.00.

N E W

-hp- 34 0A Noise F igure MeterHere is totally new equipment that makes it possible for a semi-skilled workerto do, in 5 minutes, receiver and component alignment jobs that once tookskilled engineers a full hour. Receiver performance can often be improved upto 3 db over the best adjustment previously possible. Improvem ent in receiverperformance frequently equals doubling transmitter output. Since accurate align-ment is now easy, equip men t is better maintained and peak perform ance enjoyeddaily.Model 340A is a revolutionary instrument making it possible, in 5 minutes, tooptimize receiver performance and measure noise figure directly. -hp- 340A isdirect reading in db, simple to use, automatic and needs no periodic calibration,operates over any frequency range fo r which there are noise sources, and has fastresponse to instantly track and present noise changes. In additio n to usefulnessin optimizing receiver and component performance, -hp- 340A is particularlyhelpful in designing circuit components such as IF amplifiers, crystal mixingcircuits and traveling-wave tubes.

Brief S p e c f icat onsFrequency Range: Depends on noise sourceNoise F igure Range: 3 to 30 db to CO with waveguide noise sourceAccuracy : t 0.5 db, 10 to 2 5 db; t 1 db, 3 to 30 db , waveguide noise sourceRequ i red Rcv r o r r f Amp l i f i e r Ga in : Approx. 40 db (Waveguide Voice

Approx. 50 db (IF Noise Source)

0 to 1 5 db to 00 with IF noise sourcet 0.5 db, 0 to 1 5 db, IF noise source

Source)I npu t F requency : 30 or 60 MC, selected by switchBandwid th : 1 MC minimumI npu t Impedance : 50 ohmsPrice: $715.00 (cabinet) ; 700.00 (rack mount)

-hp- 355A /B At tenu ators -0 to 1 3 2 dbHer e are two completely new design 50 ohm racy is 1 d b to 2 50 M C ; t 2 db to 500 MC.attenuators providing, together, 0 to 132 db Nomina l impedance is 50 ohms, maxim umattenuation in 1 db steps from dc to 500 MC S WR is 1.2 to 250 MC, 1 . 5 to 500 MC.-hp- 355A provides 0 to 1 2 db attenuation in1 db steps; -hp- 355B provides 0 t o 120 dbat tenuat ion in 10 db steps. One simple controlfor each at tenuator; overal l fu l l range accuracyis .25 db for -hp- 355A. For -hp- 355B, accu-

Maximum insert ion loss is 0 at dc, 0.4 db at60 MC, 1 db a t 250 MC and 1 . 5 db at 500MC . Power dissipat ion is 0.5 wat t average, 350vol ts peak. Th e at tenuators use BN C connectors.-hp- 355A or 355B, $125.00.

Mo re -hp - equipment, avai lable for m ost waveguid e f requ encies-hp- 485 Detector Mounts -hp- 532A Waveguide

Frequency Meters-hp- 752 Mult i-Hole Couplers

485D f o r S , G , Jbands factory-installed 82 1 barre t ter). AlsoP485C, l ike 485B but for P band only, hasinstalled 200 ohm 3 mw thermistor. $75.00to $145.00.sion tuning mechanisimilar model for X

New des ign for P,K , R b a n d s . W i d eband, direct reading,n o i n t e r p o l a t i o n orcharts. Comprises ahigh Q resonant cav-i t y t u n e d b y c h o k ep l u n g e r ; n o s l id i n gcontacts. T r a m i t salmost full power atresonance; resonanceindicated by 1.5 dbdip in output . Preci-sm; no back-lash. Also-band . $150 to $250.

Precision directional couplers available in 3models with co uplin g factors of 3, 10 and 20db, Coupl ing accuracy i 0.4 db except K,R bands which are * 0.7 db. Directivity bet-ter than 4 0 db f ul l range, coupl ing variat ionnot over .5 db ful l range. Primary guideSWR less than 1.05. S, G, J, H, X, P, K, Rbands, 2.6 to 40.0 KMC. $75.00 to $375.00.13


15/17

W id e B and Am pl if iers for Fast Circuit Wo rk

Fast Pulse

-hp- Travel ing-Wave TubeAmpl i f iers

Pulse ampl i f icat ionh igh output KC o 140 MC

Ampl i f i ca t ionthroughoutS b a n d

h p 490BTravel ing-Wave TubeAmpl i f i e r2 t o 4 K M C

H i g h powerS b a n dampl i f i ca t ion

h p 491ATravel ing-Wave TubeAmpl i f i e r2 t o 4 K M C

h p 492ATravel ing-Wave TubeAmpl i f i e r

Ampl i f i ca t ion 4 t o 8 K M C

Ampl i f i ca t ionthroughoutX b a n dh p 494ATravel ing-Wave TubeAmpl i f i e r

7 to 12.4 KM C

I ns t rum en t P r i m a ry U s e

Genera l purpose regula ted dcsupply for l ab andfie ld useh p 710BPower Supply

C h a r a c t e r i s t l c s P r i c e

100 t o 360 volts @ 75 ma $I 10.00

0 o 500 volts @ IO0 maIame as 710Bh p 710ALaboratoryPower Supply 225.00h p 712BPower Supply 0 to 500 volts @ 200 ma 365.00Aame as 710B

h p 715AKlystronPower Supply

Regulated beam, re f lec torsource for low power klystrons 250 to 400 volts @ 50 m a 300.00

h p 717AKlystronPower Supply Powe ring Type 5721 klystrons 800 o 1,000 volts @ 25 ma 425.00

0 o 30 v, 150 maowering transistors,s im i lar appl i cat ionsh p 721ATransistorPower Supply 145.00

-hp- o f f e r s T r a v e l l i n gWave Tube Amplifiersfor all frequencies 2 to12.4 K J I C . -hp- 490B,492A snL 494A arc- lowlevel high g ain amplificationers n, i th 30 a n ? 2 5 dbgain; thc.1. offcr .mpli-tuJc, pulse. pl i i se or FJImoduht ion . - / > [ I - 491Ais a high power trsvel-ing-nave tube anipl ihcr

I ns t r um en t P r i m a r y U ses F requenc y R ange C h a r a c t e r i s t i c s

20 and 40 db ga in, fre-quency responseI b P r i c e$ 140.00185.000 db g a in , r i se t ime0.0026 psec

15 db gain,125 peak vo lts 225.00aving a rated output of 1 watt , 2 t o 4 KMC. Allamplifiers have exclusive -hp- helical coupling sys-tem, and employ encapsulated traveling-wave tubesthat can be readily replaced. -hp- 490B 491A ,

-hp . 460A /B Fast PulseAmpl i f iers

$1,400.00. -hp- 492A 494A, 1,500.00. 30 d b g a i n ;M i l l im ic rosec r i se t ime;I O m w ou t pu t 1,400.00

30 db ga i n ;mi l l imicrosec r ise t ime;I w at t ou t pu t 1,400.00

30 d b g a in ;mi l l imicrosec r ise t ime;IO m w ou t pu t 1,500.00

-hp- 460A Wide Band Amplifiers, in cascade with-hp- 460B Fast Pulse Ampli fiers, provide up to 90db gain, 1 2 5 v open circuit. This permits directconnection to oscilloscope deflection plates. Risetime 0.00 26 psec. Will amplify millimicrosecondpulses. Over 100 MC band width for 'scopes. -hp-460AR, 185.00. -hp- 460BR, $225.00.

25 d b ga in ;mi l l imicrosec r ise t ime:5 mw output 1,500.00

-hp - Regu lated and Klystron Pow er Supp l iesN E W -hp- 721 A Trans is tor

Power SupplyS e n , c o m p le t e lyt rans i s tor i zed com-pac t regulated sup-p l y . o u t p u t 0 to 30v . continuously vari-able. 1 5 0 ma maximum output . ou tputimpeadance less than0 2 h m s . R e g u l a -tion, no load to full load, 0 . 3 % o r 30 mv whicheveris greater. Line voltage change of * 10% causesoutput change of less than 0 .3% of * 1 5 mv,whichever is greater. Front pan el switch limits maxi-mum output current prevent ing damage to t ran-sistors, etc., from accidental overload. Reads ma,v direct. $145.00.

-hp- 712B P ower SupplyThi s -hp- instrumentfeatures high regulationtion of 5 ) mv noload to full load I). 1millisecond transientresponse internal irn-pedance u.1 ohms inseries \vith 2 5 uH: R a c k mounted ins t rument ava i lab le for $15.00 less .fu l l load maximumh u m less than 500 pv, sealed transformers, chokesand condensers. 0 to 500 v, 200 ma supply andfixed -300 v tap providing a 50 ma, 300 to 800 vvariable supply for klystron operation. $365 .00A.

14


16/17

-hp - Signal Gen erato rs - 50 K C to 2 1 KMC

Ins t rument Frequency Range

hp 670SM 2.6 t o 4 K M C

NEW -hp- 6 0 6 A StandardSignal Generator

C h a r a c t e r i s t i c s

h p 687A 12.4 to 18.0 KMC

I n s t r u m e n t F r e q u e n c y R a n g e C h a r a c t e r i s t i c s

h p 606A 50 KC to 65 M C O u t p u t 0.1 p v t o 3 v . Fu l l feedback loo p, low d is tor t i on

P r i c e

990.00AS e w , ultra modern;5 0 K C t o 6 5 J I C .range, cont inuous a t -tenuation to 0 . 1 p v .NO -P A c i rcu it w i thf u l l f e e d b a c k l o o pinsures constant o u t -put f u l l range Lon. distortion, broad modulatingcapabilities. Typical hp speed, ease of operpation;occupies 1 2 bench space normally needed for gener-ators of this frequency. S990.00_1.

o u t p u t 3 v f u l l

-hp- 6 0 8 D vhf Signal Generator10 to 4 2 0 MC. Highest 5t3bility, S o incidental FM orfrequency drif t . Calibratedo u t p u t 0 . 1 p v t o 0 . 5 vt h r o u g h o u r a range BuiIt - incrystal calibra tor provides fre-qucncg check accurate within0 . 0 1 5 e ac h 1 an d 5 3 I C .M a s t e r . oscillator, intermediate-ate and output amplifier cir-cuit design. Premium qualityperformance, direct calibration, ideal for aircraft

communications equipment testing. 1,050.00.hp 608C v h f Signal G e n e r a t o r . High power ( 1 vmax.) stable, accurate generator for lab or held use.10 to 480 M C ideal for test ing receivers, ampl ifiers,driving bridges slotted lines, antennas, et:. S95O.OU .-hp- 6 2 6 A 6 2 8 A shf SignalGenerators

I o to 480 M C O u t p u t 0.1 p v t o I v in to 50 ohm load. A M, pu lse, orCW modulat ion. D i rec t ca l ibra t ionOut put 0.1 p v to 0.5 v . Inc ide nta l FM O.OOI% enti re range

h p 608C

h p 608D IO t o 420 M C

950.00

1,050.00

h p 6 1 2 A 450 to MC O u t p u t 0.1 p v t o 0.5 v in to 50 ohm load. AM, pulse, CWor square wave modulat ion. D i rec t ca l ibra t ionI 1,200.001,950.00h p 614A to 2,100 MC O u t p u t 0.1 p v t o 0.223 v i n t o 50 ohm load. Pulse, CW orFM modulat ion. D i rec t ca l ibra t ion

h p 616A to 4,000 M C O u t p u t 0.1 p v t o 0.223 v in to 50 ohm load. Pulse, CW orFM modulat ion. D i rec t ca l ibra t ionI 1,950.002,250.00u t p u t 0.1 p v to 0.223 v into 50 ohm load. Pulse CW, FMor square wave modulat ion. D i rec t ca l ibra t ion18B 3 800 o 75600 M C

h p 620A 7,000 to MC Out put 0.1 p v to 0.223 v in to 50 ohm load. Pulse FM orsquare wave modulat ion. D i re c t ca l ibra t ionO u t p u t 70 p v t o 0.223 v in to 50 ohm load. FM or squarewave modulat ion. Separate power meter and wavemeter sect ionh p 6 2 3B 5,925 to 7,725 M C

2,250.00

1,900.00

O u t p u t 3.0 p v t o 0.223 v in to 50 ohm load. Pulse, FM orsquare wave modulat ion. Separate power meter andwave meter sect ion

O u t p u t I O d b m t o -90 dbm. Pulse, FM, or square wavemodulat ion. D i rec t ca l ibra t ion

h p 624C 8,500 t o 10,000 M C

h p Io to 1 5 ,5KM C

2,265.00A

3,250.00

- h p - 628A 15 to 21 KMC O u t p u t I O d b m t o -90 dbm. Pulse, FM, or square wavemodulat ion. D i rec t ca l ibra t ion. 3,250.00Rack mounted instrument avai lable for $15.00 less.

-hp- 614A 61 6A UHF Signa l GeneratorsAmong m ost widely used signal generators. -hp- 614A, 800M C to 2 . 1 KMC, -hp- 616A, 1.8 to 4.0 KMC. Direct read-ing, di rect frequency set , no cal ibrat ion charts, wide rang e.-hp- 6 1 4 A S W R l . G , output accuracy 1 db -10 dbm to-127 dbm. 616A, SW R 1.8, outp ut accuracy 1.5 db,dbm to 27 dbm. Both have constant internal imped-ance 50 ohms. Modulat ion is internal or external pulse, orFM. -hp- 6 1 4 A o r -hp- 616A, $1,950.00.

SW R bet te r t han 1 . 2 at dbm and lower. Internalpulse, FM or square wave modulat ion; also exter-na l pu l s ing or FM ' ing . -hp- 626A, 10 to 15.5 KM C,$3,250.00. -hp- 628A, 15 to 21 KMC, $3,250.00.

-hp - Swept Frequ ency Osci l lators-hp- 6 8 6 A Electronic SweepOsc ator P r l c e

1,175.00 w i t h m o t o r

T o t a l l y n e w k i n d o fbackward - wave deviceeliminating sweep mo-t o r s , t u n i n g p l u n g e r sr a n g e l i m i t a t i o n s , et : .C o v e r s a l l o r p a r t ofX - b a n d w i t h f l e x i b le ,q u i e t e l ec t ron ic sweep .Simple to opera te, directreading, continuously adjustable sweep width an:rate, 10 mw output minimum, frequency sweeplinear with time. Has slo\v sweep for recorders; fastfo r oscilloscope; single sweep manually started orextrernally triggered external FM AM modulation.Ultimate in X-band sweep oscillators, S ? , 6 1 5 . 0 0 1 .

h p 670GM to KMC Autom at i c ad jus tab le motor -dr i ven sweep,f u l l f requency b and coverage, outpu t

10 mw ful l ran ge, f u l l modulat ionh p 670JM I 5'85 to 8'2 KM C I capabi l i t i es , d i rec t - reading f requency d ia l .Ih p 670HM 7 t o I O K M C I 175.00 w i t h m o t o r2,265.00A

IElectronical ly swept: variab le sweepr++,width. Output I O mw, SWR 2.1 or less.

Pulse, square wave, FM, AM m odu l a t i on

Data sub jec t t o change without notice.Prices f . 0 b . fac tory .

15


17/17

I n 1957, h p o c c u p i e d t h e f i r s t t w o of six85,000 square-foo t bu i l d ings fo rming a com-p le te new labora tory and manufac tur ing p lan t .New fac i l i t y i s approx imate ly one mile west ofprevious plant on a 40-acre site just south ofStanford Un ivers i t y Your v i s i t i s i nv i ted .

COMPLETE COVERAGEWon't you agree i t is simple and more t ime-saving whenyou can turn to one source for your test equipment need s?-hp- engineers are continually working to produce newequipment that antic ipates your fut ure needs, yet functionssmoothly with your existing -hp- instruments. At the 1958I .R.E. Show 20 new, basic -hp- test instruments were in-troduced. Today, -hp- makes over 300 instruments; you canchoose from the world's largest and most complete l ine

just the equipment you need. In making this choice, youare assured of -hp- qua l ity ; today the s ta ndard of theworld in electronic test instruments.To give you personal help with measuring problems, youhave available over 150 electronics specialists in everymajor U. S. metropol i tan a rea , and a round the wor ld .These men, tra ined and annually re- trained by -hp- areexperts in applying as well as sell ing and servicing -hp-instruments. Call them when you can use personal, com-petent help, in your plant, today.

-hp- Sa les and Serv ic e Representa t ives in the Un i ted Sta tes and Can adaA l b u q u e r q u e , N e w M e x i c o C l e v e l a n d 2 4 . O h i o H o u s t o n 5 . Te x as P h o en i x , A r i z o n a S t . L o u is 1 7 , M i s s o u r iNeely Enterprises1 0 7 Wash in g to n S t . , S. E.ALpine 5-5586A s b u r y P o r k , N e w J e r s eyI . E. Ro b in so n Co m p an y905 Main StreetKEl lo g 1 -3 1 5 0

A t l a n t a 5 , G e o r g i aBiv in s Ca ld v e l l , In c .3 1 3 3 Map le Dr iv e , P;.E.CEd ar 3 -7 5 2 2B a l t i m o r e , M a r y l a n dHorman Associates , Inc.635 St . J o h n s R o a dHOp k in s 7 -2 2 9 0

B o s t o n A r e aBurlington, MassachusettsYewell Associates , Inc.Mid d lesex Tu rn p ik eBRo wn in g 2.9000B r i d g e p o r t 8 , C o n n e c t i c u tYewell Associates , Inc.1101 East Main StreetFo res t 6 -3 4 5 6C a m p Hill Pennsy lvan iaI. E. Ro b in so n Co m p an y2120 Market StreetREg en t 7 -6 7 9 1

C h i c a g o 4 5 , . Il l i n o i sCrossley Associates , Inc.2 7 1 1 Wes t Ho ward S t ree tSHeld rak e 3 - 8 5 0 0Cuby i i gh t 1958 Hewle t t -Pa

s. Sterl ing Coin an5 82 7 M ay f ie ld f o a JHIl l c res t 2.8080Dal las 9 , TexasEarl Lipscomb AssociatesP.0 Box 7084FLeetwood 7-1881 andEDison 2-6667D a y t o n 1 9 , O h i oCrossley Associates , Inc.2 8 0 1 Far Hi l l s Av en u eA x m i n s t e r 9 - 3 59 4

D e n v e r 1 0 , C o l o r a d oLah an a Co m p an y1 8 8 6 So u th Bro ad wayPEar l 3 -3 7 9 1D e t r o i t 3 5 , M i c h i g anS Sterl ing Corn any1 5 3 1 0 Wes t McNicHo ls Rd .BRo ad way 3-2900

E n g l e w o o d , N e w J e r s e yR . hi. C. Associates391 G r a n d A v e n ueL o w e l l 7-3933Fo r t M y e r s , F l o r i d a

Art hur Lynch Associates35 \Vest N ort h Shore AvenueW y a n d o t t e 5 -2 1 51H i g h P o i n t , N o r t h C a r o l i n aBiv in s Ca ld wel l , In c .1923 N. Mai n S t ree tTel . : 2-6873

ikard Company

Earl Lipscomb AssociatesP . 0 Box 6573JAckson 4-9303Ind ianapo l i s 20 , Ind ianaCrossley Associates , Inc.5320 No. College AvenueCLifford 1-9255K a n sa s C i t y 3 0 . M i s s o u r iHarr i s -Han so n Co m p an y7916 Paseo Blvd.HI l l a nd 4 -9 4 9 4L a s C r u c e s , N e w M e x i c oNeely Enterprises126 S. Water S t ree tJAckson 6-2486Los A n g e l e s , C a l i f o r n i aNeeiy Enterprises3939 Lan k ersh im B l rd .No r th Ho l ly wo o d , Ca l i f .STan ley 7 -0 7 2 1N e w Y o r k 2 1 , N e w Y o r kR . M . C. Associates

236 East 75th StreetTRafa lg ar 9 -2 0 2 3P h i l a d e l p h i a A r e aU p er Darb y , Pen n sy lv an iaf E . Robinson Company7404 West Chester PikeSHerwo o d 8 -1 2 9 4

Neely En te rp r i ses Harr i s -H an so n Co m p an y641 East MissouriCRes two o d 4 -5 4 3 1 MIssion 7 -4 3 5 02 8 1 4 So u th Bren two o d Bo u lev ardP i t t s b u r g h 2 2 , P e n n s y lv a n i aS. Ster l in g Co m p an yRo o m 8 1 5 , Park B ld g .3 5 5 Fifth AvenueATlan t i c 1 -9 2 4 8

St . Pau l 14 . MinnesotaCrossley Associates , Inc.8 4 2 Ray m o n d Av en u eMId way 6 -7 8 8 1P o r t l a n d 9 . O r e g o n1238 N. \V Gl i sanCAp i to l 7 -1 2 8 1

A R V A c

S a c r a m e n t o 1 4 , C a l i f o r n i aNeely Enterprises1317 - 15th StreetGI lb er t 2 -8 9 0 1Son D i e g o 6 , C a l i f o r n i aNeely Enterprises1055 Shafter StreetA c a d e m y 3 - 8 1 0 6

S a n F r a n c is c o A r e aSan Ca r lo s , Ca l i fo rn iaNee ly En te rp r i s es501 Laurel StreetLYte l l 1 -2 6 2 6S e a t t l e 9 9 , W a s h i n g t o nA R V A120 \Vest Tho mas StreetATwater 4 -7 3 3 7

To r o n t o 1 0 . O n t a r i oAt las In s t ru m en t Co r o ra t io n , Ltd50 W i n g ol d l v e n u eRu sse l l 1 -6 1 7 4 -Tucson. A r i zonaNeely En te rp r i s es232 So. Tucson Blvd.M Ain 3 -2 5 6 4

V a n c o u v er 2 , B r i t i s h C o l u m b i aAt las In s t ru m en t Co rp o ra t io n , Ltd106-525 Seymour StreetM u t u a l 3 - 5 8 4 8Washington. D. C. A r e aRo ck v i l l e , Mary lan dHorman Associates , Inc.941 Roll ins AveHAzelwo o d 7 -7 5 6 0

W i n n i p e g , M a n i t o b aAt las In s t ru m en t Co rp o ra t io n , Ltd72 Princess StreetWHi teh a l l 3 -8 7 0 7Reg is t e red T rad em ark o f th e Hew le t t -Pack ard Co m p an y@

HEWLETT-PACKARD COMPANY2 7 5 P A G E M I L L R O A D P A L 0 A L T O , C A L I F O R N I A , U . S . A .

C A B L E H E W P A C K D A V E N P O R T 5 - 4 4 5 1

Date post:	04-Jun-2018
Category:	Documents
Upload:	yu3za
View:	235 times
Download:	1 times

HP Catalog 1958 05 Short

Documents