HSE Tool Box Talk

HSE Tool Box Talk

Tool Box Talk No Topics

HSE-TBT-001 Excavation

HSE-TBT-002 Confined Space

HSE-TBT-003 Ladder

HSE-TBT-004 Cranes and Overhead Wire

HSE-TBT-005 Hand Signal For Crane Operator

HSE-TBT-006 Use of Chain Saws

HSE-TBT-007 Construction Equipments

HSE-TBT-008 Fire Safety

HSE-TBT-009 Use of Electricity

HSE-TBT-010 Portable Electrical appliances

HSE-TBT-011 Welding Operations

HSE-TBT-012 Welding and Cutting Safety Tips

HSE-TBT-013 Use of Compressed Gases

HSE-TBT-014 Use of Hand Tools

HSE-TBT-015 Safe Stacking on Site

HSE-TBT-016 Work Permits

HSE-TBT-017 Safety Signs

HSE-TBT-018 Head Protection

HSE-TBT-019 Ear Protection

HSE-TBT-020 Eye Protection

HSE-TBT-021 Work at height

HSE-TBT-022 Clothing

HSE-TBT-023 Hand Protection

HSE-TBT-024 Dust and Fumes

HSE-TBT-025 Foot Protection

HSE-TBT-026 First Aid

HSE-TBT-027 Defensive Driving

HSE-TBT-028 Driving On Steep Slopes

HSE-TBT-029 Driving Safely in Winter

HSE-TBT-030 Defensive Driving and Road Safety

Introduction:

Removal of earth/soil digging either manually(shovel) and mechanically(JCB,proclaims etc..,)

Excavations areas exceeding 1.2m depth are inspected daily and thoroughly and examined by a

competent person on weekly basis.

Excavated soil should be poured least maintaining 1Mts from edge of excavated area and area is

barricaded temporarily or permanent on the basis of requirement.

Adequate supply of suitable timber for protection from shoring at excavated area.

Main points:

If a trench or an excavation is 1.2m or deeper stairways, ramps, or ladders will be used as safe means of access and egress.

Provide an adequate supply of suitable barriers and t raffic notices, and ensure adequate protection and warnings are provided for members of the public.

Ensure that the loads, plants or materials are not placed near the edge.

Consumption of alcohol is strictly prohibited at excavated area i.e.., workmen and equipment operators.

Demarking of all underground services to secure and protect once they are exposed.

Discussion:

All workers should be conscious at work site and are required to inform

to higher authorities if materials are required in sufficient

Alcohol is strictly prohibited in site

Parking of vehicles least maintained 1m or of depth of excavation

which ever is greater.

ISSUE NO:01 REV NO:00 EFFECTIVE DATE:01-04-2010 FORM NO: VISPL/HSE/TBT/001

Project Name: Topic: EXCAVATION Date:

Tools Box Talk No: Trainer

Introduction: confined spaces can include cellars, pits, tanks, drains, manholes, sewers, and even some

types of excavation. Some are more obvious than others, but confined spaces are more common on

construction sites than often realized.

Main points:

o Consider what may comprise a confined space on your site!

o A risk assessment should be carried out for all confined spaces. o Never ever work alone in a confined space.

Discussion Points :

o Hazards include oxygen depletion/enrichment, suffocation, toxic and flammable atmospheres, physical

dangers (plant), biological hazards, etc.

o Confined space atmospheres should be checked prior to entry.

o Suitable PPE should be worn which may include breathing apparatus, and may require specialist

training.

o Employees working in confined spaces should be fit and healthy

o Permit to work systems should be used where applicable (these should include rescue proce dures).

o Work in confined spaces must be supervised, either physically or by communications/ monitoring

equipment (remember failure procedures).

o Ensure any recovery equipment is checked and serviceable prior to starting work.

o Ensure all know the alarm procedure including location of nearest telephone, etc.

Project Name: Topic: Confined Space Date:


o Dont eat, drink, smoke, or used naked flames in confined spaces or in close proximity to entry.

o Ensure there is suitable access/ egress

o Remain alert to any changes in the situation/ environment. IF IN DOUBT get out !

GLOVES AND

MASKS MAY

PROTECT INDIVIDUALS SAFE SYSTEMS OF WORK PROTECT EVERYONE !


Introduction:

Use ladders only for simple work of short duration. They should be used primarily as a means of access and NOT as a working platform.

Ladders shall be of good construction with no missing or defective rungs, of sound material and of adequate strength for the purpose for which it is used and is properly maintained.

Only erect ladders on a firm and level base.

Main points:

Secure a straight ladder at the top. When it is impracticable to do so, firmly secure the ladder at the base by some effective means or by any person.

Rise ladders at least 1.05m for handhold above their landing place or above the highest rung.

The rungs and the footwear of the user shall be in good condition shall be free from moisture, dirt and grease.

Discussion:

Do not erect straight ladder at a base angle exceeding 75 degrees or a 4 (rise):1 (base) ratio.

Do not carry tools or materials in hand when climbing up or down. If necessary, use a tool holster to carry hand tools to

spare hands for holding the ladder.

Do not use aluminum ladders or other ladders which are electrically conductive for electrical work unless they have

been fully insulated especially at footing of the ladder.

Use wooden or fiber-glass ladders for electrical work or when working near electrical conductors etc. Wear safety harness with lanyard anchored properly when working on the ladder at height of 2m or more if the

provision of working platform is not reasonably practicable.

Inspect the ladder for any defects before each use. Do not use wooden ladder that has been painted as painting may cover up the defects. Display warning label to the defective ladder

Project Name: Topic: LADDERS Date:



Introduction:

There are many dangerous situations on a construction site, but operating hoisting equipment close to overhead wires is more than just dangerous, it's a matter of li fe and death! The following guidelines should help us prevent potentially deadly contact:

Main points:

o Keep cranes a safe distance from power lines. For lines rated 50 kV or below, minimum clearance between the lines and machines or loads must be 10 feet plus 0.4 inch for each 1 kV. over 50 kV., or twice the length of the line insulator, but NEVER less than 10 feet.

Discussion Points:

o Use a qualified signalperson when the crane is within boom's length of a line.

o The signalperson must warn the operator when the machine is approaching the lines since the

operator may not be able to accurately judge the distance.

o The signalperson should have no other duties while the machine is working near the power line.

o Do not rely on ground rods for safety. They provide little or no protection.

o People touching the crane or load will still draw enough current to kill, even with the best ground rods

in place.

o In addition, don't rely on proximity warning devices, hook insulators, insulating boom guards, s wing

limit stops, etc. as each has serious limitations.

Project Name: Topic: CRANES AND OVER HEAD

WIRES

Date:


o Except for the operator, keep all personnel away from the crane when working near power line Don't

allow anyone to touch the load, crane, or crane hook until the signalperson indicates that it is safe to

do so.

o Exercise caution when working near overhead lines having long spans. These tend to swing laterally in

the wind and contact can occur.

o Use caution when moving cranes. Uneven ground can cause the boom to weave or bob into lines.

o Ensure a route is plainly marked when cranes must travel beneath power lines.

o 'Rider' poles should be erected on each side of the crossing approach to guarantee that the boom will

be lowered to a safe position.

o Avoid using tag lines except when it is possible for the load to spin into the power line. All rope will

conduct electricity.

DUMP TRUCKS & OVERHEAD WIRES SPELL DANGER, TOO! BE ALERT IN INDUSTRIAL AREAS & NEAR TEMPORARY POWER LINES.


Introduction:

When using hand signal be sure the operator can see you and that both of you understand all the signals.

Main points:

o You and the operator are in charge of an important operation. o Co-workers lives depend on your skills. o A wrong signal could cause a serious injury or possible death. THINK SAFETY!

Discussion Points :

o HOIST -- Extend the right arm straight out and raise the forearm to vertical, forefinger pointing up, then

move hand in small horizontal circle.

o LOWER -- Extend the right arm downward, forefinger pointing down, then move hand in small

horizontal circle.

o RAISE BOOM -- Extend right arm straight out, fingers closed and thumb pointing upward.

o LOWER BOOM -- Extend right arm straight out, fingers closed and thumb pointing downwar d.

o SWING -- Extend right arm away from body, point with finger in direction of swing of boom.

o STOP -- Right arm extended down with wrist bent and palm down and open.

o EMERGENCY STOP -- Right arm extended, palm down, then move hand rapidly right and left.

o TRAVEL -- (both tracks, crawler cranes only) Use both fists in front of body, making a circular motion

about each other to indicate the direction of travel - forward or backward.

o DOG EVERYTHING -- Clasp hands in front of the body.

Project Name: Topic: HAND SIGNALING FOR

CRANES

Date:


o RAISE BOOM & LOWER LOAD -- Extend right arm with thumb pointing up, then flex fingers in and out

as long as load movement is desired.

o LOWER BOOM & RAISE LOAD -- Extend right arm with thumb pointing down, then flex fingers in and

out as long as load movement is desired.

As for the rest of us on the job, stay alert when working near any crane operation. Avoid working under a moving load -- stay clear of the counter balance -- and always remember that the crane operator's vision may be obscured; be on guard for your own safety.

KEEP ALL PARTS OF A CRANE, FALL LINES, HOOK, BLOCK, AND LOAD A MINIMUM OF 15 FEET FROM ALL ELECTRICAL LINES.


Introduction:

Chainsaws are increasingly used within the construction industry, often in a manner for which they are not originally designed. They are particularly dangerous and can cause serious injury, even in the hands of a trained operator.

Main points:

o All chainsaw operators should have received formal training

o Chainsaw operators should wear suitable PPE

o Chainsaws should be maintained in a serviceable and safe condition.

Discussion Points:

o Before using a chainsaw carry out the following checks:

Check guards are in place, in good condition and secure.

Check chain brake operation. Check security of casing and all nuts and screws. Check throttle and interlock for serviceability. Check chain sharpness, tension and freedom of movement. Check chain lubricating reservoir top up if required.

o Ensure you have all the required PPE and that it is serviceable. This should include leggings.

o Always engage the chain brake and place on a secure surface clear of any obstructions before starting

the chainsaw.

o Never make adjustments to the chainsaw whilst it is running.

o Maintain a firm grip, using both hands, on the chainsaw when in operation, and aim to complete cuts at

full throttle where practicable.

o If you have to stage cuts, take extreme care when re-entering the previous cuts.

o Always beware of the timber closing in on the saw cut and pinching the chain.

o Never place any part of your body in the saws line of cut.

o Before moving with the chainsaw, switch it off, apply the chain brake, and fit the scabbard over the

chain. Carry by front handle with chain facing rearwards.

o Refuel chainsaws in well ventilated areas and atleast 3 metres away from where you are going to

use the chainsaw (wipe up any spilt fuel ). Do not smoke and ensure no naked flames are nearby.

Check for fuel leakage and ensure fuel cap is correctly replaced.

WE WERE GIVEN TWO HANDS AND TWO LEGS LETS KEEP IT THAT WAY!


Project Name: Topic: USE OF CHAIN SAWS Date:


Introduction:

Construction Equipment used on construction jobs often creates dangerous conditions. Any moving equipment such as skip loaders, backhoes, trenchers, cranes, hi-lifts, trucks, you name it, should be respected and

avoided.

Don't just assume that the operator sees you. You could wind up injured or worse. And don't depend on

hearing a horn or an alarm to warn you that moving equipment is near. You may not be able to hear the equipment 's alarm over other construction noise.

Main points:

o When you see that equipment is traveling backwards keep out of the way and stand clear until the

operator has completed his maneuver.

o Never cut across the path behind any unit while it is backing. You could easily trip and fall under the

equipment. For the same reason you should never ride on the running boards, steps or drawbar or any

equipment, even for a short distance.

o During backing, the operator should have the project foreman clear the area behind the unit and

provide direction. No operator should back a piece of equipment into and area without someone

clearing the area and giving signals.

Project Name: Topic: CONSTRUCTION

EQUIPMENTS/DANGERS

Date:


Discussion Points :

o Watch out for swinging counterweights on equipment such as cranes. There is often a pinch-point

between the counterweights and some obstruction when the unit swings. Make sure there is enough

room for workers to pass and if there is not - shut off the area to any access.

o Never ride on or near material that is being t ransported by equipment. The load could shift and you

can be thrown to the ground. Also, clearance may not allow for your position and you can be crushed

between overhead or side obstructions.

o If you must ride on equipment, make sure that all parts of your body are inside the unit, including your

arms and legs. In addition, it at all possible, get off any portable scaffold or work platform while the unit

is being moved. The time it takes to get off will be much less than the time lost if you fall or the unit tips

over.

o Never walk alongside moving equipment. Keep in the clear in case it slides or turns, or the load shifts.

o When you are working near equipment operating in the vicinity of power lines, don't touch or come in

contact with the frame of the unit or the load cables.

o There is always the chance that the boom of the unit may hit the power lines. Warn the operator and

the foreman any time you see this possibility and follow their instructions.

o Don't walk under loads on cranes and hoists. Always take the path that avoids danger.

o Never clean, adjust, lubricate, repair or work on a machine that is in operation. Stop the machine

before working on it and replace the guards as soon as it is done and before operation is resumed.

o The safest thing to do around construction equipment is keep away while the equipment is in

operation. If you must be near the equipment, make sure the operator knows you are working nearby

and stay alert.

KEEPING YOUR MIND ON WHERE YOU ARE IN REALTION TO THE EQUIPMENT WILL NOT ONLY PREVENT INJURIES BUT COULD SAVE YOUR LIFE!


Introduction:

Fire is a major risk both to persons and to property. You can either help prevent fires, or you can help start/allow them.

Main points:

o Ensure you are aware of the fire drill including the means of raising the alarm, escape routes, and the

assembly point.

o Ensure you know where the nearest fire point is, what types of fire extinguisher are there, what types

of fire they can be used on, and how they should be used (never put yourself at risk!)

o Never obstruct any fire points, fire doors or escape routes

Discussion Points:

o Never misuse or tamper with anything provided for the fire prevention or fighting (never discharge fire

extinguishers during horseplay)

o Dont hang clothing/materials over or near heating equipment.

o Control rubbish dont le paper, rags, etc, accumulate

o Store flammable liquids in suitable containers well away from any sources of ignition, keeps lids on

containers when not in use.

o Control smoking ---use designated areas if necessary.

o Dont overload electrical sockets one plug per socket!

o If electrical equipment is not in use then switch off at the mains

Project Name: Topic: FIRE AND SAFETY Date:


o Bitumen boilers, soldering irons, gas rings, etc., must be placed on non-combustible stands.

o Carry out residual heat checks 30-60 minutes after any hot work has been carried out.

o Always have afire extinguisher within arms reach when carrying out hot work.

o Obtain ho working permits where applicable.

FIRE

DESTROYS PEOPLE AND PROPERTY SAFE PEOPLE PREVENT FIRES.

Stop Smoking In si te Premises Smoking is prohibited


Introduction:

Electricity is silent, invisible, and potentially fatal, so it deserves the utmost respect. Never ever take electricity for granted, and never assume a circuit is dead.

Main points:

o The lowest practical voltage should be used on construction sites, which should not exceed 110v

o Only suitable and authorized electrical supplies and equipment should be used, which should be

installed and maintained by trained electricians.

o Suitable protection such as circuit breakers, fuses, and residual current devices, must always be used,

along with the correct load ratings.

Discussion Points:

o Electrical cables should be suspended where practicable to avoid damage and damp (which also

reduces a trip hazard)

o Carry out visual checks of plugs, sockets and cables if any damage is identified then remove from

service and report immediately.

o Any cable joins must utilize proper connector blocks, not just insulating tape.

o Never use lighting sockets to power equipment.

o Ensure cables are long enough for the task they should not be pulled taut.

o The inner insulation of cables should never be visible the outer insulation should extend into plugs

and equipment and fully utilize cable grips.

Project Name: Topic: USE OF ELECTRICITY Date:


o Blown fuses should be replaced immediately never make do with a bodge (NOTE : If a replaced

fuse immediately blows again then it is indicative of a problem requiring the attention of an electrician)

o For electrical maintenance work ensure the mains supply is disconnected.

o Never overload electrical sockets one plug per socket!

o Where emergency stop switches are present ensure they are tested regularly.

LIVE ELECTRICITY CAN EQUAL A DEAD PERSON.

Preserve natural resources

dont waste electricity


Introduction:

Electrical appliances on site are subject to harsh treatment and can easily become worn and/ or damaged. They can become lethal.

Main points:

All portable electrical appliances should be subject to regular inspection and

maintenance by a competent person (electrician)

They must only be used at the correct voltages This should be 110v

maximum on a construction site.

Visual checks of cable casing and plugs should be carried out prior to use. If

any damage is identified then remove from service and report immediate

Discussion Points :

o Check that suitable protection devices such as fuses, circuit breakers and

residual current devices are in place, and that any fuses have the correct load

ratings.

o Only use portable electrical appliances for the purpose for which they were

designed.

o Ensure switches are working properly at the earliest opportunity (prior to

starting the task).

o Disconnect power tools when not in use.

Project Name: Topic: PORTABLE ELECTRICAL

APPLIANCE

Date:


o All power tools must be properly earthed unless it is an approved type that

does not require earthing.

o Use of portable electrical appliances will often require wearing of suitable PPE

such as eye and/ or ear protection ensure you wear them as required.

o Never connect portable power tools to lighting sockets

o Never use blunt, worn or damage bits and accessories.

ITS TOO LATE TO CARRY BASIC CHECKS AFTER AN ACCIDENT !


Introduction:

Welding is a multi risk operation to both operatives and others in the vicinity that must be strictly controlled.

Main points:

o Only trained operatives can undertake welding operations

o Welding operations will always require the wearing of suitable personal protective equipment.

o Fire is an ever present risk when welding and suitable precautions must be taken

Discussion Points:

o Infra red rays, visible light rays and ultra violet radiation are hazardous to the eyes and skin.

Wear suitable skin and eye protection (basic eye protection will always be required, and

normally filter protection will be required).

o Consider the risks to other employees and provide suitable protection/procedures such as

confining welding to specific areas, use of welding screens, etc.

o Wear suitable clothing that covers bare skin and is flame resistant

o Welding and cutting produces fumes and gases that can harm the respiratory system (some

fumes from lead or toxic coated materials can also affect the rest of the body)- wear filtered

respirators for low volume work. Permanent welding locations should have local exhaust

ventilation fitted.

Project Name: Topic: WELDING OPERATON Date:


o Have Co2 or dry powder fire extinguishers at hand, check areas where welding operations

have been undertaken at least 30 minutes after work has been completed for any residual fire

risks

o Compressed gas cylinders pose a fire and explosive risk.

o Ensure only the minimum number of cylinders are stored on sites as are required, ensure they

are stored upright, ensure flash back arrestors are fitted at cylinder gauge ends and non-return

valves at inlets to the blowpipe, ensure valves are closed prior to moving.

o The primary risk from electric arc welding is electric shock check insulation, earthling,

equipment condition and protective devices.

GLOVES AND MASKS PROTECT THE USER SAFE SYSTEMS OF WORK PROTECT EVERYONE


Introduction:

Fuel gasses may be toxic. Check a copy of the manufacturer's MSDS. Oxygen and fuel gas hoses are not interchangeable. They must be easily distinguishable by either color or surface characteristics sensitive to touch. Keep welding hoses clear of any falling metal, slag or sparks.

Main points:

o Do not tamper with the relief valve or remove it from a regulator.

o Examine hoses before attaching to welding torch handles or regulators. Never use a defective hose or

a hose in doubtful condition.

o Never perform any welding or cutting operation without proper eye protection.

Discussion Points:

o Always keep gas cylinders secured properly and in a vertical position. Keep valve protection caps in

place whenever cylinders are not in use. Close valves completely on empty cylinders.

o Always open cylinder valves slowly and carefully.

o When a cylinder wrench is needed on the valve, keep the wrench close at hand so the valve can

turned off quickly if necessary.

o Place gauges if they become damaged and keep dust covers in place. Perform welding in a well -

ventilated area.

o Always keep gas cylinders secured properly and in a vertical position. Keep valve protection caps in

place whenever cylinders are not in use. Close valves completely on empty cylinders.

o Always open cylinder valves slowly and carefully.

Project Name: Topic: SAFETY TIPS OF

WELDING AND GAS CUTTING

Date:


o When a cylinder wrench is needed on the valve, keep the wrench close at hand so the valve can

turned off quickly if necessary.

o Place gauges if they become damaged and keep dust covers in place. Perform welding in a well-

ventilated area.

PEOPLE CAUSE ACCIDENTS NOT EQUIPMENT!

LPG AND COMPRESSED GASES ARE VALUABLE TOOLS BUT CAN BE LETHAL IF NOT USED

CORRECTLY


Introduction:

Compressed gases, including liquefied Petroleum Gas (LPG), are used extensively on construction sites and provide a valuable source of energy. Misuse, however, can result in fires, serious accidents and injuries.

Main points:

o Treat all cylinders as full

o Regularly inspect hoses, cylinders and valves for damage and wear and tear.

o The likes of Oxy/Acetylene cylinders should only be used by competent persons.

Discussion Points:

o Keep cylinders away from the sun, artificial heat, flammable materials, corrosive chemicals, etc. Do not

smoke in vicinity.

o If a cylinder catches fire, then call the fire brigade. Cool the cylinder with water spray only if safe to do

so.

o Always have fire extinguishers located within reasonable proximity to any hot work being carried out.

Use hot work permits if appropriate.

Project Name: Topic: USE OF COMPRESSED

GASES

Date:


o Ensure everyone knows fire procedures including alarm signal, evacuation routes, assembly area, and

correct use of fire extinguishers (including types!)

o Avoid damage to cylinder valves and fittings. Dont use then as carrying aids. Open valves slowly and

close sufficiently to cut gas supply do not use excessive force.

o Always secure acetylene cylinders in upright position. Ensure all cylinders are stored so that they

cannot fall or oll.

o Consider manual handling of cylinders they are heavy! Use a trolley for full size cylinders or get

assistance

o Always unload cylinders from lorries, vans, etc, by fitting not by dropping/ sliding

o Transport cylinders in vehicles in vehicles with good ventilation ensure relevant signs (compressed

gases) are clearly displayed on vehicles.

PEOPLE CAUSE ACCIDENTS NOT EQUIPMENT!

LPG AND COMPRESSED GASES ARE VALUABLE TOOLS BUT CAN BE LETHAL IF NOT USED

CORRECTLY


Introduction:

Misuse and poor maintenance of hand tools result in countless injuries every year. Whilst many may be considered minor all are avoidable by complying with relatively simple procedures.

Main points:

o Always only use the right tool for the job.

o Maintain all tools in a serviceable condition If unserviceable either repair or replace.

o Control/protect tools with obvious risks

Discussion Points :

o Use correct size spanners/sockets for nuts if using adjustable, be extra cautious as these are more

prone to slipping.

o Always keep hands behind cutting edges when working

o Grind down mushroomed heads of chisels, punches, etc to prevent splinters flying off.

o Do not use screwdrivers as chisels handles splinter.

o Replace split or damaged wooden handles do not tape or wire up.

o Regularly check hammerheads, etc for security of fixings.

o All files should be fitted with suitable wooden handles.

o Where necessary use specialist tools (insulated screwdrivers on live electrics)

o Protect sharp edges/ points of tools.

o Keep tools in tool boxes or racks when not in use.

o Where applicable ensure suitable PPE in worn (eye protection, gloves, etc)

MINOR ACCIDENTS CAN RESULT IN MAJOR INJURIES

(A SPLINTER FROM A MUSHROOMED CHISEL HEAD CAN BLIND YOU!)


Project Name: Topic: USE OF HAND TOOLS Date:


Introduction:

Unsafe stacking can cause injuries as a result of collapse, or when materials have to be collected from stacks. In contrast, safe stacking not only reduces risk , but also enhances site efficiency.

Main points:

o Only stack materials in designated areas ensuring that escape routes, doorways etc, are not

obstructed.

o Stack on level, firm surfaces, use packing where appropriate, and never stack materials higher than

three times the base width.

o Make sure you wear suitable protective clothing such gloves and safety boots, and use -handling

accessories as appropriate.

Discussion Points :

o Use machinery where possible eliminating the need for manual handling. Where manual handling is

unavoidable, carry out an assessment

o Stack small pipes in racks, while large diameter pipes must be securely chocked at the base.

o Do not stack pipes in pyramids they are not sufficiently stable.

o Large concrete rings must be laid flat so they cannot roll.

o Small sized timbers should be stacked in racks.

o Bearers should be used for larger timbers and joists use cross packing to keep level

o Where possible keep different length timbers in different stacks.

o Large prefabricated panels should be stacked flat or in suitable racks they should never be leaned

against temporary structures, parts of building, or where the wind could affect them

o Store bricks/blocks/palleted materials on level surfaces and ensure heights are controlled only stack

two packs high, an place upper stack squarely on lower stacks

o If banding is damaged or materials are displaced then do not stack materials on top where necessary

make lower stacks safe.

YOU WERE BORN WITH TWO HANDS, TWO LEGS LETS KEEP IT THAT WAY!


Project Name: Topic: MATERIAL STACKING AT

SITE

Date:


Introduction:

Permits are needed in construction because certain work conditions present hazards during particular activities. These activities must be evaluated and determined to be safe prior to any work -taking place.

There are various types of permits. Typical groups that may be found in construction include --

excavation permits, hot work permits, confined space permits, personnel basket permits, lockout -tag out permits, electrical hot work permits, line break permits, crane permits, heavy/critical lift permits, and there may be others required on your worksite.

Main points:

o Permits enable us to have safer working environments. Misuse may cause an accident and possibly a

death. No one wants that!

o A permit is a document allowing you to do something that involves a hazard of some kind. Follow it to

the letter.

o See your supervisor about who to contact to get a permit issued.

Discussion Points :

Project Name: Topic: WORK PERMIT SYSTEM Date:


o First, always inspect the area you are about to work in.

o Identify fire watchers and fire extinguisher locations.

o Insist that all required signatures are obtained prior to starting work.

o Look for obvious hazards.

o Review emergency procedures with all crew members.

o Make sure all workers are wearing the required personal protective equipment.

o Inspect your hand tools and check other equipment you may need to use.

o Follow all visual signs and instructions.

o Be prepared for the unexpected.

o Don't take any chances.

o Your li fe and others that work in the area will depend on each member of the crew doing

the job correctly.

o If your permit requires testing, be sure to have the testing done prior to entry.

o Lock, tag, and try procedures are a must when preparing for a plant shutdown,

equipment shutdown, equipment isolation, or release and control of stored energy.

o Watch for pinch points when you are blocking lines and closing valves.

o A permit is usually issued for a specific amount of time.

o When the permit becomes void or invalid, the permit must be reissued

o Contact your supervisor for reissue of permit.

FAILURE TO FOLLOW PERMIT PROCEDURES AND SAFE WORK PRACTICES WILL CAUSE ACCIDENTS


Introduction:

Signs, tags, and color codes are used on construction sites to warn employees of hazardous conditions and help them in case of an emergency.

Main points:

o For signs to be effective they must be understood by the work force they are trying to inform.

o Most signs are in English, however there are times when they should be in the language of the

work force that is present.

o If everyone speaks Hindi, then signs should be in that language. Pictograph signs may also be used.

Discussion Points:

o RED -- is the basic color used to inform workers of an immediate hazard.

o Most DANGER signs are in red and white with white lettering on the red portion and black letters in the

white area. Examples are: DANGER - HIGH VOLTAGE, DANGER - KEEP OUT, DANGER - NO

SMOKING.

o Red is also the color that identifies fire protection equipment and apparatus, safety cans, fire

extinguishers and alarms. And of course there is the familiar red octagon with STOP in white letters.

o YELLOW -- signs are messages of caution and warn you to take action to protect yourself. Caution

signs are yellow with black lettering. Examples: CAUTION - WATCH YOUR STEP, CAUTION - LIVE

POWER SUPPLY, CAUTION - EYE PROTECTION REQUIRED.

Project Name: Topic: SAFETY SIGNS Date:


o ORANGE -- is the color used to identify dangerous machine parts. These are locations that can cause

major lacerations, crushing injuries or electrical shock. For example, gears, pulleys and rollers may be

marked with this color.

o PURPLE -- is used to identify radiation hazards. You will see it if you work at a nuclear power plant.

Purple identifies where radioactive materials are stored or handled. Site X-ray technicians will have

containers or vehicles marked with radiation signs to alert workers.

o Another sign is the SAFETY INSTRUCTION SIGN. These signs give you various kinds of safety

information. The signs have a white background with a green panel that has white lettering. Example:

This project has worked _ days without a lost time accident.

SIGNS PROVIDE YOU WITH SOME TYPE OF INFORMATION.

TAKE TIME TO READ AND UNDERSTAND THE MESSAGE.

THE SIGN IS THERE FOR YOUR PROTECTION!


Introduction:

Safety Helmet is used for head protection. Safety helmet is a piece of personal protective equipment designed to individually protect an employee when all other methods of protection cannot.

Main Points:

o Wear a safety helmet when there is the risk of being hit by falling objects.

They should be used when there is a danger of falling objects striking somebody on the head

or when somebody could hit their head against something.

o Wear safety helmet while on or near a construction site.

Discussion Points:

o You may also remove your helmet when eating lunch or dinner in a designated eating area

o No person shall enter a construction site unless he is wearing a suitable safety helmet.

o Destroy, remove and replace all worn, defective or damaged helmets.


Project Name: Topic: HEAD PROTECTION Date:


Introduction: Noise induced hearing loss is the most common occupational health hazard there is, and it is incurable. Once you are deaf, you stay deaf.

Main points:

o Compressors, concrete mixers, circular saws, breakers, etc, can all damage your hearing.

o You do not have to be using noisy equipment to be affected by it, just be I the vicinity.

o If you have t shout to be heard then the noise level can be regarded as high enough to warrant the

wearing of ear protection.

Discussion Points :

o Wear ear protection at all times when exposed to noise hazard (obey noise hazard warning signs)

o Wear proper ear protection and wear it properly (ie cotton wool is no good for ear protection and ear

muffs are no good worn over a balaclava)

o If ear plugs are used ensure they are a good fit, are fitted properly, and are kept clean

o Earmuffs must be good fit, particularly where the seal fits the head, and must be worn the correct way

around.

o Ensure hands are clean when handling all types of ear protection, and store ear protection in a clean

environment.

o Do not alter pressure of ear defenders by bending the band.

Project Name: Topic: EAR PROTECTION Date:


o Report any damaged, lost or serviceable ear protection immediately

o Consider options for reducing noise in the workplace, ie turn off unused machinery, keep cement mixer

and compressor covers closed, ensure airlines do not leak, fit mufflers to tools where applicable, move

noise source away, shield noise source, etc.

YOU COULD PAY THE PRICE FOR GETTING IT WRONG FOR THE REST OF YOUR LIFE!


Introduction: It only takes a small fragment or splinter to cause irreparable damage to the eye, but most risks can be significantly reduced, if not eliminated, by simply wearing suitable eye protection..

Main points:

o You have a legal obligation to use eye protection provided in accordance with the regulations, and you

should never enter an area where eye protection is required unless wearing such.Ensure eye

protection provided fits you comfortably and is suitable for the job

o Look after any eye protection provided. Keep them clean and report any damaged, lost or

unserviceable eye protection immediately.

Discussion Points :

o Even if not carrying out a task with an obvious eye hazard, you may be at risk from others nearby.

Always have your eye protection with you and if any doubt wear it!

o Eye protection only works when worn over the eyes it is useless worn over the head or around the

neck

o Never watch any welding processes unless wearing suitable protection

o Should you get something in your eye, or receive any sort of eye injury, then get a trained first aider to

look at it.

o Always consider eye protection when compressed air, hazardous substances, cartridge- fired tools,

power tools, power washers, hand tools such as chisels, etc, are in use.

EYE PROTECTION IS REPLACEABLE EYES ARE NOT!

Project Name: Topic: EYE PROTECTION Date:



Introduction:

Any works i.e.., 2 meters from ground level is referred as height work.

To arrest fall protection, the following should be provided

(a) working platforms.

(b) guard-rails, barriers, toe-boards and fences.

(c) coverings for openings.

(d) gangways and runs.

1. Take adequate steps to prevent any person on a construction site from falling from a height of 2 metres or more. 2. In special circumstances of work where the use of working platforms are impractical,

other means of fall prevention such as scaffolds, safety nets and safety harnesses/belts shall be provided.

Discussion:

1. Mostly safety harness shall be used for fall protection because it could reduce injuries to the waist caused by

the shock from a fall. Safety harness or belt anchor point should be directly above and the lanyard shall be left with

the minimum free length.

2. Safety harnesses or belts are a specially worn and attached to suitable anchor points for:

rigger works, works from suspended cages and climbing permanent ladders

3. The length of lanyard shall be adequate to have free moment at work place.

4. Make sure so that the working plat form is secure and check it will support the weight of worker using it and any

materials ,equipments they are likely to use or store on it.

5. Ensure work place is cordoned during execution of work avoiding fall of materials below and multilayer jobs are

observed.

6. When using harness remember that they need to be able to attach themselves before they move into position

where they are relying on the protection provided by the harness.


Project Name: Topic: WORK AT HEIGHT Date:


Introduction:

Suitable and sensible clothing is a pre-requisite of site safety and can provide effective protection against a wide range of hazards.

Main points:

o Wear head protection it can save your life!

o Wear Safety shoes/boots that provide protection to your toes and to the soles of your feet.

o Wear gloves where there is any risk to your hands

o Wear hi-visibility clothing/vests be seen.

o Keep clothing reasonably clean to protect against dermatitis, fire, etc.

o Avoid loose clothing especially loose ends that can get in machinery, etc.

Discussion Points :

o Skin Cancer is deadly keep skin covered when working in sunny conditions.

o Avoid exposed skin when working with substances such as cement, tar, insulation, etc.

o If clothing you are wearing becomes contaminated then remove it and get it washed.

o If working with hazardous substance consider use of suitable coveralls

o Wear any PPE provided, and look after it so that it can look after you.

Project Name: Topic: CLOTHING Date:


o Jewellery, including rings, chains, etc, can be hazardous near machinery and when working on plant

consider taking off or tapping up (also reduces wear and tear)

o Always dress properly, even for short jobs, and be prepared to swap or add clothing as required for

specific.

DRESSING SAFELY ISNT BEING SILLY ITS BEING SENSIBLE.


Introduction: Wear suitable gloves when working or handling sheet metal and other objects, which have

sharp edges and corners.

Main Points:

Wear gloves when doing welding and cutting works.

Wear gloves, it will help to you for better grip while handling oily components

Gloves are not recommended for operators working on rotating parts of machinery.

Wash hands properly with disinfectant soap and clean water before drinking, eating or

smoking Wash hands immediately after each operation on site when the situation warrants.

Discussion points:

The gloves for protecting worker hands from the chemical solutions, liquid solutions, electrical shocks,

sharp objects ,abrasive and hard parts should be long ,extending well beyond the wrists.


Project Name: Topic: HAND PROTECTION Date:


Introduction:

Exposure to dust and fumes should be prevented where practicable, and must at least be controlled; breathing in dust and fumes can have both acute and chronic effects, and can cause long-term health problems

Main points:

o Dust arise from cutting, sanding and grinding operations, and can also be found when working with old

lead pipes (lead oxide dust) or stripping out fibrous insulation.

o Fumes arise from a wider source of origins including welding operations, use of hazardous

substances, heating metals such as lead burning off old paints etc.

o The effects vary greatly, but examples of potential hazards include lung disease from silica dust as a

result of cutting/scrabbling concrete, cancer from cutting/ sandin g hardwood dust, metal fume fever

from welding fumes, and lung cancer/asbetosis from exposure to asbestos, to name but a few.

Discussion Points:

o Where practicable, plan operations/tasks to eliminate exposure to dust and fumes.

o

o Where elimination is not practicable, then exposure to dusts and fumes must be controlled

o Use tools with dust extraction system if possible

o Consider the use of portable extraction equipment.

o Consider use of local exhaust ventilation where practicable.

Project Name: Topic: DUST AND FUMES Date:


o As a last resort use personal protective equipment/respiratory protective equipment. Ensure it is

suitable and that you know how to use it properly, and how to maintain it.

o Always remember other workers in the area they may also require protection.

YOU CAN LEAVE A DUSTY PLACE ANYTIME ---- BUT ASTHMA LASTS FOREVER!


Introduction: Safety Shoes is used for Foot Protection.

Main Points:

o Wear suitable safety shoes or ankle boots when working anywhere where there is high risk of foot

injuries from slippery or uneven ground, sharp objects, falling objects etc.

Discussion Points:

o All safety footwear, including safety shoes, ankle boots and rubber boots shall be fitted with steel

toe caps. For electrical workers, where electrical hazard exists,

o safety footwear with electrical resistant soles shall be fitted as appropriate.

o Workers working in construction site should always wear safety shoes.


Project Name: Topic: SAFETY SHOES Date:


INTRODUCTION

The immediate action takes for a injured or treatment given to injured at immediate is said to be first aids.

MAIN POINTS:

At least one person trained in first aid shall be included in the team of responsible persons in charge

of first aid

boxes. Contractors shall provide a person trained in first aid to a construction site with 30 to 99

workmen.

At least two persons trained in first aid are required for a construction site with 100 or more workmen.

A Person Trained in First-Aid means a person who:

(a) holds a current certificate of competency in first aid issued by the St. John Ambulance

Association or Red Cross.

(b) is a registered nurse within the meaning of the Nurses Registration Ordinance.

(c) has otherwise completed a course of training in first aid approved by the

Commissioner for Labour.

First Aid

A construction site with five or more workmen shall have a FIRST AID BOX (preferably a portable one) marked plainly FIRST AID in English. Separate first aid box shall be

provided for every 50 workers on site. The location of the nearest first aid box and the name of the person in charge of the box

shall be displayed in

that work place. The required content of the first aid box shall be replenished as necessary by the responsible

person or first aider.

A readily serviceable STRETCHER shall be provided to a Construction site with 50 or more workmen.

DISCUSSON POINTS:

If you have been taught on how to give artificial respiration, use the method with which you

are most familiar.

Do not delay, start artificial respiration immediately and persevere with it, for many

Project Name: Topic: FIEST AID Date:


hours if necessary.

Note: The brain begins to suffer irreparable damage if left without oxygen for a few

minutes

Send for, but never wait for a doctor. If the victim is removed to a hospital, artificial

respiration must be continued during the journey. Mouth to mouth method (not to be

used for a gaseous incident.


Introduction:

More than 41,000 people lose their lives in motor vehicle crashes each year and over two million more suffer disabling injuries, according to the National Safety Council. The triple threat of high speeds,

impaired or careless driving and not using occupant restraints threatens every driverregardless of how careful or how skilled.

Driving defensively means not only taking responsibility for yourself and your actions but also keeping an eye on "the other guy."

Main points:

o Don't start the engine without securing each passenger in the car, including children and pets. Safety

belts save thousands of lives each year! Lock all doors.

o Remember that driving too fast or too slow can increase the likelihood of collisions.

o Don't kid yourself. If you plan to drink, designate a driver who won't drink. Alcohol is a factor in almost

half of all fatal motor vehicle crashes.

Discussion Points:

o Be alert ! If you notice that a car is straddling the center line, weaving, making wide turns, stopping

abruptly or responding slowly to traffic signals, the driver may be impaired.

o Avoid an impaired driver by turning right at the nearest corner or exiting at the nearest exit. If it

appears that an oncoming car is crossing into your lane, pull over to the roadside, sound the horn and

flash your lights.

o Notify the police immediately after seeing a motorist who is driving suspiciously.

o Follow the rules of the road. Don't contest the "right of way" or try to race another car during a merge.

Be respectful of other motorists.

o Don't follow too closely. Always use a "three-second following distance" or a "three-second plus

following distance."

o While driving, be cautious, aware and responsible.

ACCIDENT OR SAFETY CHOICE IS YOURS! PENALTY COULD BE DEATH!


Project Name: Topic: DEFENSIVE DRIVING Date:


Introduction:

There have been a number of incidents in relation to Vehicles ASCENDING & DESCENDING Slopes.

In a number of these incidents it has been concluded that a loss of control occurred at some point

during the ascent or descent.

Main points:

o Always STOP and Assess the gradient.

o Ensure 4 wheel drive is engaged.

o Select 1st gear initially and drive up the gradient slowly to test for traction.

o If traction is good, drive a straight course up the gradient (Never traverse steep gradients as tipping

may occur) .

Remember if ever you are in doubt STOP and dont take RISKS

Discussion Points:

VEHICLE FAILING TO CLIMB ASCENTS

1. Apply the foot brake soon as forward motion is lost. 8. Check slope is clear behind.

2. Allow engine to stall (do not engage clutch) 9. Release the hand brake.

3. Keep foot hard on foot brake. 10. Release the foot brake.

4. Apply the hand brake. 11. Check slope is clear behind.

5. Depress the clutch pedal. 12. Start engine.

6. Select reverse gear. 13. Steer down slope.

7. Release the clutch pedal.

STEEP DESCENTS

1. Stop vehicle and apply hand brake. 8. Release hand brake. 2. Check the gradient 9. Drive forwards. 3. Start the vehicle. 10. Keep left foot away from clutch

4. Select 4-wheel drive. 11.Keep right foot over brake. 5. Engage differential lock. 12. Allow engine to slow vehicle

6. Select low ratio. 13. Drive Straight down the gradient.

7 Select first gear. 14. Do not attempt to change gear.

Note: before descending ensure you exit is clear of obstacles and obstructions

REMEMBER

NEVER CHANGE GEAR

ALLOWING ENGINE TO STALL (DO NOT USE CLUTCH)

IF WHEEL SPIN OCCURS, DECELERATE IF YOU FOLLOW THESE SIMPLE STEPS THE YOU CAN REDUCE THE POTENTAL OF HAVING A INCEDENT AS A DRIVER

SOME TIMES YOU DONT GET A SECOND CHANCE!


Project Name: Topic: DRINING ON STEEP

SLOPES

Date:


Introduction:

The leading cause of death during winter storms is transportation accidents. Many accidents could be avoided if drivers took time to learn and practice these tips for driving safely during snowy and icy conditions. Failing to allow yourself enough time to stop is a major cause of winter driving accidents.

Main points:

o During slippery conditions stopping distances can triple.

o Driving at a slower speed, anticipating stops at traffic lights and intersections, and applying brakes

sooner than normal will help ensure accident-free stops.

o When braking, brake carefully with short, rapid application of the brakes. Always allow plenty of extra

space between you and other vehicles to minimize the need for quick stops.

o Acceleration, turning, and passing also present dangers during winter. Accelerate slowly to avoid loss

of traction and subsequent loss of control.

o Turn slowly, with caution, to avoid sliding into a stationary object or the path of an oncoming vehicle.

o Avoid sudden movements.

o Pass with care because passing lanes are not maintained as well as driving lanes.

o Again, leave extra space between yourself and other vehicles so there's room to maneuver in case

something goes wrong.

o During a skid, steer cautiously in the direction you want the car to go.

Discussion Points:

o Always use your seatbelt.

o Turn on your headlights during adverse weather conditions. Overcast skies and falling snow limit

visibility. It is important to see and be seen.

o Like all the signs say, bridges and overpasses freeze before the roadway. Use extra caution on these.

o Remember that driving in winter weather conditions causes physical and mental fatigue and reduces

reaction times. Get plenty of rest and adequate nutrition. Don't drive while you're sleepy or on

medication that causes drowsiness.

o Prepare your vehicle well ahead of time. Check fluid levels, tire pressure, lights, and the battery. Have

a mechanic give your vehicle a winter check-up and make any necessary repairs.

o Stock an emergency kit containing heavy clothes and a blanket, traction material such as sand or kitty

litter, tire chains, a small shovel, first aid kit, flashlight, jumper cables, and a bright cloth to use as a

flag.

o While driving, be cautious, aware and responsible.

YOUR SAFETY MEANS SAFETY OF YOUR FAMILY.


Project Name: Topic: DRIVING SAFELY IN

WINTER

Date:


Introduction:

Defensive driving is to prevent injury and damage and to save lives, money and time inspite of the unfavorable conditions around you and the actions of others. It involves anticipating situations or factors that can possibly lead to accidents, and maneuvering your driving in away that enables you to

stay out of accident situations.

Main points:

o Knowledge of traffic rules, behind the wheel procedures and hazards involved. (Do not expect

all drivers to know them

o Alertness To conditions around you and your vehicle that may affect your driving and also to the

illegal acts and driving errors of the drivers.

o Fore sight for anticipating immediately and long- range developments and preparing for them

o Judgement in knowing what choices you have for making the right decision and acting on it

promptly.

o Concern for accident prevention, regardless of who is right or wrong.

Discussion Points:

o Adjust your driving to the conditions around you, like the conditions of your vehicle, weather,

traffic, road, besides your own physical and mental condition

o Ensure that the vehicle is in good mechanical and electrical conditions with good tyres.

o Take good care of your car battery and maintain the electrical system well.

o Maintain correct tyre pressure.

o Change engine oil as recommended by the vehicle manufacturer.

o Before starting your vehicle, go round the vehicle for a quick visual from outside and peep below

the vehicle to see any tell tale marks of oil or water leak

o Watch out for any vehicle fault and rectify the same as soon as possible.

YOUR SAFETY MEANS SAFETY OF YOUR FAMILY.


Project Name: Topic: DEFENSIVE DRIVING

AND ROAD SAFETY

Date:


Date post:	07-Jan-2016
Category:	Documents
Upload:	abdulkather
View:	544 times
Download:	54 times

HSE Tool Box Talk

Documents