Date post: | 26-Sep-2018 |
Category: |
Documents |
Upload: | truongcong |
View: | 212 times |
Download: | 0 times |
GeneralHydraulically driven rotary angle broom
25” diameter brush available in 6’ (72”), 7’ (84”) and8’ (96”) broom widths
Broom speed up to 200 rpm
Standard with storage stands
FrameConstructioned of 3-1/2” O.D. x .03” wall round tubularcross-member; 2 brush arms (formed from 1/4” plate)
Self aligned bearings, with grease-able pillow block
BrushRefillable core with flat wafers - poly, wire, or combination (poly and wire combination on one wafer)
Spacers and hubs manufactured from 20 gauge mild-steel strap 2” wide.Broom removal without disconnecting hoses
Allow for broom to follow surface contour
Follow in swept path
SwingHydraulic angle change 30° left/right
Parallel arms on top and bottom allow broom to “float”
Brush HoodCoverage of 155° of broom
Formed edge fold for strength
Pre-drilled for installation of deflector
Ends covered by formed end plates
CastersTwo 10” heavy duty casters with 360° swivel
Brush LiftProvided by cylinder with 8” stroke and 2” bore
FinishOne coat of epoxy primer and one polyurethane top coat
Painted M-B yellow
Specifications
Available OptionsDirt Deflector
Electric/hydraulic swing and lift systemSight Indicators
Sprinkler SystemIndependent Hydraulic System
Reserving Valve
®
HTP A Rear Mounted Hydraulic Broom for Tractors
Snow GrassDirt Debris
www.m-bco.com • M-B Attachments • 1.800.558.5800Note: Additional fees may apply (freight, export fees, dealer or factory installed hoses, valves and couplers, installation and service fees).
Equipment and products shown in this literature are for demonstration purposes only. Actual products offered for sale may vary in use, design, requirements and safety features.M-B Companies reserves the right to improve our products and make revisions in designs, specifications and standards for equipment without notice and without incurring obligations.
M-B® is a registered trademark of M-B Companies, Inc. © 2015 M-B Companies, Incorporated. All Rights Reserved. 2015 M-B Attachments Product Guide 0615A Effective 06/2015 - 05/2016
Prices starting at for standard modelAll prices subject to change without notice.
Contact M-B for Custom Requests
Available OptionsBroom Width 7-foot (84”) Broom - add $370 8-foot (96” Dual Motors) Broom - add $1,305Brush Filament Poly (Polypropylene) - add $0Motor Size6-7 Foot Optional Dual Motor (for prime mover with 25 to 40 GPM) 9000 in.lbs torque - add $525 Low Flow (for prime mover with 8 to 11 GPM) 3200 in.lbs torque - add $100 Dual Low Flow (for prime mover with 15 to 24 GPM) 6400 in.lbs torque - add $6758 Foot Low Flow (for prime mover with 15 to 24 GPM) 6400 in.lbs torque - add $200Method of Swing Manual Swing - add $0 Electric/Hydraulic Swing and Lift (Valve and control box actuate the swing cylinder) - add $1,200 Max 30 GPM. Required if tractor does not have remote available for lift and swing functions. Electric/Hydraulic Swing and Lift with Reverse - add $1,525 Mounting Kit Custom Mount Design (This applies to mounts not previously desgined by MB) - add $2,500 No Mount - subract $100Independent Hydraulic system (IHS) Independent Hydraulic system (IHS) - add $2,100 (Includes Rear 540 PTO hydraulic pump, relief valve, 3-point hydraulic reservoir and hoses to broom) Required if tractor/loader auxiliary hydraulic system cannot supply 8 GPM @ 2,000 psi IHS Options: Tank Location Front Tank (mounts on broom mounting frame) - add $150Optional Equipment Deflector (number of feet needed x $30/ft) - cost varies 45 Gallon Sprinkler System (Customer provides tank mounting location) - add $1,290 12 Volt 24 Volt 150 Gallon Three-point Mount Sprinkler System - add $2,180 (cannot be used with three-point hydraulic tank) Sight Indicators - add $80Recommended Spare Parts (for current pricing refer to the online Parts Guide at www.m-bco.com/attachments) Part Number Description 100-108617 Caster Wheel - $325.56 201-169353 Hydraulic Motor (Std. Flow) - $726.56 201-169657 Hydraulic Motor (Low Flow) - $643.39 201-169532 Motor Shaft - $232.55 201-92039 Motor Seal Kit - $89.20 203-142346 Cylinder, Lift - $245.85 203-142346 Cylinder, Swing - $245.85 380-150742 Pin, Swing - $10.23 380-76379 Pin, Clevis 1/2 x 3” for Stand - $4.00 380-84739 Pin, Hair Clip for Stand - $2.51 For brush replacements see “Replacement Brush Guide” section or online at www.m-bco.com
Total Cost $____________
www.m-bco.com 1.800.558.5800®
M-B Companies, Inc.
$7,040**Standard model HTPHydraulic Broom for Tractors6-foot (72”) Broom - subtract $1305Poly/Wire BrushSingle Single Motor (25 to 45 GPM; 9000 in.lbs torque)Hydraulic Swing Cylinder OnlyM-B YellowAgriculture Tractor Front Mount Frame (inquire about models)
410-94050 Storage Stand - $39.90 410-169418 Splined Hub - $96.62 410-176888 Caster Fork - $123.46 600-169345 Bearing, Pillow Block 1-3/4 I.D. - $60.81601-150722 Kit, Bearings, Seals, Spacers - $30.69
Note: Additional fees may apply (freight, export fees, dealer or factory installed hoses, valves and couplers, installation and service fees). Equipment and products shown in this literature are for demonstration purposes only. Actual products offered for sale may vary in use, design, requirements and safety features.
M-B Companies reserves the right to improve our products and make revisions in designs, specifications and standards for equipment without notice and without incurring obligations.M-B® is a registered trademark of M-B Companies, Inc. © 2015 M-B Companies, Incorporated. All Rights Reserved. 2015 M-B Attachments Product Guide 0615A Effective 06/2015 - 05/2016