Trend thermAL® Hybrid
Awning WindowTECHNICAL DATA
Features & Benefits
Size Range
Ordering Details
Installation
Cross Sectional Views
Confidentiality Notice: This document and the information it contains are copyright and confidential to Trend® Windows & Doors Pty Limited. Disclosure, use and copying in any form whatsoever, except as authorised
by Trend® Windows & Doors in writing, are strictly prohibited. Patents and Design Registrations pending.
1Trend thermAL® Awning Window | TAA | Mk-1 | 30 Nov 2012
Please note that drawings are not to scale
Features & BenefitsTrend thermAL® Awning Window
Confidentiality Notice: This document and the information it contains are copyright and confidential to Trend® Windows & Doors Pty Limited. Disclosure, use and copying in any form whatsoever, except as authorised
by Trend® Windows & Doors in writing, are strictly prohibited. Patents and Design Registrations pending.
2Trend thermAL® Awning Window | TAA | Mk-1 | 30 Nov 2012
1 Glazing Trend thermAL® is designed to
accommodate upto 24mm double glazed units for maximum energy efficiency. With over 60 different glazing options there is a solution for any climate in Australia.
Among the lowest U-Values and SHGC available but at a significantly lower cost when compared to similar systems.
U-Value down to 2.5 SHGC wide range of 0.53 - 0.27 Cooling Efficiency 66% Heating Efficiency 72%
2 Composition Aluminium external surface for
maximum strength which can be powder coated in a range of standard and designer colours for bold external finish
Rigid polymer ERP is available in 3 standard steadfast colours to complement internal finishes with a subtle appearance but complementing the external finish.
Rigid polymer ERP internal surface designed to reduce energy transfer for highest energy efficiency
Rigid polymer ERP is impact modified to ensure minimal damage even during construction.
Rigid polymer ERP is pre–stressed to eliminate excessive shrinkage or expansion and is also uV stabilised to withstand the harsh Australian climates
3 Key Lock Scissor Winder Trend thermAL® Awning window
Secura winder mechanism is designed specifically for high performance, security and reliability.
The Secura winder can be used in even the harshest environment without worry of corrosion.
Secura hardware is available in powder coat finishes with stainless steel stay mechanism.
Restricted openers to 100mm are available for safety options.
Keyed lock is standard for added security.
4 Window Placement Care should be taken with locating
opening awning windows in pedestrian traffic areas.
5 Protective Wrapping Protective wrapping for delivery
to site is a standard for all Trend thermAL® products.
6 Options Easy to fit flyscreens can be fitted
and removed from the inside.
Wide range of powdercoat finishes available including timber powdercoat finishes.
ERP Colours Anodic Natural Matt White Matt Stone Beige
Maximum Size Maximum size of single Awning is
2100mm (h) x 910mm (w)
Bushfire Protection
Xtreme® bushfire protection that has
been tested by CSIRO to BAL–40,
which is fully compliant to AS1530.8.1
within AS3959–2009 is available.
Size RangeTrend thermAL® Awning Window
Please note that drawings are not to scale
Confidentiality Notice: This document and the information it contains are copyright and confidential to Trend® Windows & Doors Pty Limited. Disclosure, use and copying in any form whatsoever, except as authorised
by Trend® Windows & Doors in writing, are strictly prohibited. Patents and Design Registrations pending.
3Trend thermAL® Awning Window | TAA | Mk-1 | 30 Nov 2012
All windows and doors are designed to 700pa velocity and 200pa water rating. For higher ratings consult Trend Windows & Doors
NOTES Hinged from the top, the sash of the Trend thermAL® awning windows swings out from the bottom, giving your home good ventilation – even in wet weather. The sash design offers a wide viewing area, while its excellent sealing qualities ensure added climate control. In gusty conditions, the sturdy scissor winder mechanism prevents the window slamming.
610
666
910
966
1210
1266
1510
1566
1810
1866
2110
2166
2410
2466
2710
2766
600
656
900
956
1000
1056
1200
1256
1365
1421
1800
1856
2100
2156
1800
1856
2100
2156
STUD OPENIN
G
WINDOW
TAA0906
TAA1006
TAA1206
TAA1406
TAA1806
TAA2106
TAA1806T
TAA2106T
1365
TAA0909
TAA1009
TAA1209
TAA1409
TAA1809
TAA2109
TAA1809T
TAA2109T
TAA0912
TAA1012
TAA1212
TAA1412
TAA1812T
TAA2112T
TAA0915
TAA1015
TAA1215
TAA1415
TAA1815
TAA2115
TAA1815T
TAA2115T
TAA0918
TAA1018
TAA1218
TAA1418
TAA1818
TAA2118
TAA1818T
TAA2118T
TAA0921
TAA1021
TAA1221
TAA1421
TAA1821T
TAA2121T
TAA0924
TAA1024
TAA1224
TAA1424
TAA1824
TAA2124
TAA1824T
TAA2124T
TAA0606 TAA0609 TAA0612 TAA0615 TAA0618 TAA0621 TAA0624 TAA0627
TAA0927
TAA1027
TAA1227
TAA1427
TAA1827
TAA2127
TAA1827T
TAA2127T
Ordering DetailsTrend thermAL® Awning Window
Please note that drawings are not to scale
Confidentiality Notice: This document and the information it contains are copyright and confidential to Trend® Windows & Doors Pty Limited. Disclosure, use and copying in any form whatsoever, except as authorised
by Trend® Windows & Doors in writing, are strictly prohibited. Patents and Design Registrations pending.
4Trend thermAL® Awning Window | TAA | Mk-1 | 30 Nov 2012
All windows are illustrated as viewed from outside. Codes shown are for plain windows.
Manufactured from 55mm section aluminium and Rigid Polymer extrusion.
The first two numbers ofcode indicate approximate height, the last two numbers indicate approximate width.
Sash Style Options:Standard option, eg window codeTAA0906
Configuration Options:F indicates FixedLF indicates Left Hand\FixedFR indicates Fixed\RightHandFF indicates Fixed\FixedLFR indicates Left Hand\Fixed\Right
HandFLF indicates Fixed\Left Hand\FixedFRF indicates Fixed\Right Hand\FixedFFF indicates Fixed\Fixed\FixedT after the size indicates a TransomE indicates Xtreme bushfire window
(located at the end of the code)
Aluminium exterior and Extruded Rigid Polymer (ERP) interior. ERP interior skin is available in three colours - white, anodic natural matt and stone beige
For information on double-glazing or wind ratings, please contact Trend® Windows & Doors Sales Representa-tive.
InstallationTrend thermAL® Awning Window | Building In Detail | Brick Veneer - 230mm wall
Please note that drawings are not to scale
Confidentiality Notice: This document and the information it contains are copyright and confidential to Trend® Windows & Doors Pty Limited. Disclosure, use and copying in any form whatsoever, except as authorised
by Trend® Windows & Doors in writing, are strictly prohibited. Patents and Design Registrations pending.
5Trend thermAL® Awning Window | TAA | Mk-1 | 30 Nov 2012
TIMBER REVEAL
BRICKWORK
FLASHING BY BUILDER
STUD
STUD
FLASHINGBY BUILDER
FRA
ME
SIZE
STU
D O
PEN
ING
= F
RA
ME
SIZE
+ 6
0mm
BRICK SILL
PACKINGBY BUILDER
FIXINGS AT450mm CENTRES
TIMBER REVEAL
JAMB
SILL SUPPORTBY BUILDER
SILL PLATE
NO PACKING12mm CLEARANCE
STU
D O
PEN
ING
= F
RA
ME
SIZE
+ 6
0mm
FRA
ME
SIZE
10mm MINIMUM CLEARANCE BETWEEN SILL BRICK AND WINDOW SILL WHERE TIMBER FRAME IS USED
10mm CLEARANCEBETWEEN SOFFIT LINING AND WINDOW HEAD
QUAD BYBUILDER
SILL FLAP
SOFFIT LINING
SILL
HEAD
PACKINGBY BUILDER
FIXINGS AT450mm CENTRES
TIMBER ARCHITRAVE BY BUILDER
TIMBER REVEAL
TRIMMER
FLASHINGBY BUILDER
OUTSIDE
HEADER
Please note that drawings are not to scale
InstallationTrend thermAL® Awning Window | Building In Detail | Double Brick - 280mm wall
Confidentiality Notice: This document and the information it contains are copyright and confidential to Trend® Windows & Doors Pty Limited. Disclosure, use and copying in any form whatsoever, except as authorised
by Trend® Windows & Doors in writing, are strictly prohibited. Patents and Design Registrations pending.
6Trend thermAL® Awning Window | TAA | Mk-1 | 30 Nov 2012
CEM
ENT R
END
ER
FLASHING BY BUILDER
BRICKWORK BRICKWORK
BUILDING IN LUGS AT450mm CENTRES
JAMB
FRA
ME
SIZE
BRICK SILL
FLASHING BY BUILDER
BUILDING IN LUGS AT450mm CENTRES
BRICKWORK
FLASHING BY BUILDER
HEAD
FRA
ME
SIZE
ALUMINIUM ANGLE AND FIXING BY BUILDER
SILL FLAP
CEMENT RENDER
CEMENT RENDER
STEEL LINTEL BY BUILDEROUTSIDE
BRICKWORK BRICKWORK
JAMB
Please note that drawings are not to scale
InstallationTrend thermAL® Awning Window | Building In Detail | Aluminium Cladding on Studs
Confidentiality Notice: This document and the information it contains are copyright and confidential to Trend® Windows & Doors Pty Limited. Disclosure, use and copying in any form whatsoever, except as authorised
by Trend® Windows & Doors in writing, are strictly prohibited. Patents and Design Registrations pending.
7Trend thermAL® Awning Window | TAA | Mk-1 | 30 Nov 2012
TIMBER REVEAL
ALUMINIUM OR VINYLWALL CLADDING
FLASHING BY BUILDER
STUD
OPE
NING
= F
RAM
E SI
ZE +
60m
m
FRAM
E SI
ZE
WEATHERBOARDCLIP OPTIONAL
ALUMINIUM
OR VINYL WALL CLADDING
STUD
STUD
JAMB
FIXINGS AT450mm CENTRES
PACKINGBY BUILDER
FLASHING BY BUILDER
TIMBER REVEAL
SILL PLATE
SILL FLAP
FLASHING BY BUILDER
DRESS SARKING INTO CLADDING "U" TRIM AT HEAD AS SHOWN
ALUMINIUM OR VINYLWALL CLADDING
12mm CLEARANCE
STUD
OPE
NING
= F
RAM
E SI
ZE +
60m
m
FRAM
E SI
ZE
OUTSIDE
NO PACKING
SILL
HEAD
FIXINGS AT450mm CENTRES
PACKINGBY BUILDER
TIMBER ARCHITRAVE BY BUILDER
TIMBER REVEAL
HEADER TRIMMER
Please note that drawings are not to scale
Cross Sectional Views
Confidentiality Notice: This document and the information it contains are copyright and confidential to Trend® Windows & Doors Pty Limited. Disclosure, use and copying in any form whatsoever, except as authorised
by Trend® Windows & Doors in writing, are strictly prohibited. Patents and Design Registrations pending.
8Trend thermAL® Awning Window | TAA | Mk-1 | 30 Nov 2012
Trend thermAL® Awning Window | Awning Single Lite - Double Glazed
SILL
OUTSIDE
HEAD
5526
64
53
5712.5
JAMB
JAMB
OUTSIDE
5526
53
74
12.547
Please note that drawings are not to scale
Cross Sectional Views
Confidentiality Notice: This document and the information it contains are copyright and confidential to Trend® Windows & Doors Pty Limited. Disclosure, use and copying in any form whatsoever, except as authorised
by Trend® Windows & Doors in writing, are strictly prohibited. Patents and Design Registrations pending.
9Trend thermAL® Awning Window | TAA | Mk-1 | 30 Nov 2012
Trend thermAL® Awning Window | Awning/Fixed with Low Lite - Double Glazed
HEAD
OUTSIDE
SILL
F
TRANSOM
5526
64
5392
53
3431 31
Please note that drawings are not to scale
Cross Sectional Views
Confidentiality Notice: This document and the information it contains are copyright and confidential to Trend® Windows & Doors Pty Limited. Disclosure, use and copying in any form whatsoever, except as authorised
by Trend® Windows & Doors in writing, are strictly prohibited. Patents and Design Registrations pending.
10Trend thermAL® Awning Window | TAA | Mk-1 | 30 Nov 2012
Trend thermAL® Awning Window | Awning with Fixed Low Lite - Double Glazed
JAMB OUTSIDE
JAMB
FF
JAMB
JAMB
OUTSIDE
5526
53
74
12.547
313112.5
18
31
Please note that drawings are not to scale
Cross Sectional Views
Confidentiality Notice: This document and the information it contains are copyright and confidential to Trend® Windows & Doors Pty Limited. Disclosure, use and copying in any form whatsoever, except as authorised
by Trend® Windows & Doors in writing, are strictly prohibited. Patents and Design Registrations pending.
11Trend thermAL® Awning Window | TAA | Mk-1 | 30 Nov 2012
Trend thermAL® Awning Window | Awning/Fixed - Double Glazed
HEAD
OUTSIDEOUTSIDE
HEAD
SILL SILL
F F
5526
53
64
12.5
57
31
5526
31
20
31
Please note that drawings are not to scale
Cross Sectional Views
Confidentiality Notice: This document and the information it contains are copyright and confidential to Trend® Windows & Doors Pty Limited. Disclosure, use and copying in any form whatsoever, except as authorised
by Trend® Windows & Doors in writing, are strictly prohibited. Patents and Design Registrations pending.
12Trend thermAL® Awning Window | TAA | Mk-1 | 30 Nov 2012
OUTSIDE
JAMB
MULLION
F
JAMB
5526
53
74
3418
9
923131
Trend thermAL® Awning Window | Awning/Fixed - Double Glazed
Please note that drawings are not to scale
Cross Sectional Views
Confidentiality Notice: This document and the information it contains are copyright and confidential to Trend® Windows & Doors Pty Limited. Disclosure, use and copying in any form whatsoever, except as authorised
by Trend® Windows & Doors in writing, are strictly prohibited. Patents and Design Registrations pending.
13Trend thermAL® Awning Window | TAA | Mk-1 | 30 Nov 2012
Trend thermAL® Awning Window | Awning/Fixed with Fixed Low Lite - Double Glazed
OUTSIDE
HEAD
TRANSOM
SILL
F
FF F F
F
HEAD
OUTSIDE
SILL
TRANSOM
5526
64
5392
53
3431 31
713431 31
31
Please note that drawings are not to scale
Cross Sectional Views
Confidentiality Notice: This document and the information it contains are copyright and confidential to Trend® Windows & Doors Pty Limited. Disclosure, use and copying in any form whatsoever, except as authorised
by Trend® Windows & Doors in writing, are strictly prohibited. Patents and Design Registrations pending.
14Trend thermAL® Awning Window | TAA | Mk-1 | 30 Nov 2012
Trend thermAL® Awning Window | Awning/Fixed with Low Lite - Double Glazed
OUTSIDE
MULLION
F
FF
JAMB
OUTSIDE
JAMB
MULLION
F
JAMB
5526
53
74
3418
9
923131
JAMB
26
55
3171
12.5
31
FF
Please note that drawings are not to scale
Cross Sectional Views
Confidentiality Notice: This document and the information it contains are copyright and confidential to Trend® Windows & Doors Pty Limited. Disclosure, use and copying in any form whatsoever, except as authorised
by Trend® Windows & Doors in writing, are strictly prohibited. Patents and Design Registrations pending.
15Trend thermAL® Awning Window | TAA | Mk-1 | 30 Nov 2012
Trend thermAL® Awning Window | Awning/Fixed/Awning - Double Glazed
FF F
HEAD
OUTSIDEOUTSIDE
HEAD
SILL SILL
5526
53
64
12.5
57
31
5526
31
20
31
HEAD
OUTSIDE
SILL
5526
53
64
12.5
57
Please note that drawings are not to scale
Cross Sectional Views
Confidentiality Notice: This document and the information it contains are copyright and confidential to Trend® Windows & Doors Pty Limited. Disclosure, use and copying in any form whatsoever, except as authorised
by Trend® Windows & Doors in writing, are strictly prohibited. Patents and Design Registrations pending.
16Trend thermAL® Awning Window | TAA | Mk-1 | 30 Nov 2012
Trend thermAL® Awning Window | Awning/Fixed/Awning - Double Glazed
JAMB
F
MULLION
JAMB
MULLION
OUTSIDE
OUTSIDE
5526
5364
34 9
92
52
319
5352.8
12.5
Please note that drawings are not to scale
Cross Sectional Views
Confidentiality Notice: This document and the information it contains are copyright and confidential to Trend® Windows & Doors Pty Limited. Disclosure, use and copying in any form whatsoever, except as authorised
by Trend® Windows & Doors in writing, are strictly prohibited. Patents and Design Registrations pending.
17Trend thermAL® Awning Window | TAA | Mk-1 | 30 Nov 2012
Trend thermAL® Awning Window | Awning/Fixed/Awning with Low Lite - Double Glazed
F
FF F
HEAD
OUTSIDE
SILL
TRANSOM
5526
64
5392
53
3431 31
OUTSIDE
HEAD
TRANSOM
SILL
713431 31
31
HEAD
OUTSIDE
SILL
TRANSOM
5526
64
5392
53
3431 31
F
F
F FF F
F
F
Please note that drawings are not to scale
Cross Sectional Views
Confidentiality Notice: This document and the information it contains are copyright and confidential to Trend® Windows & Doors Pty Limited. Disclosure, use and copying in any form whatsoever, except as authorised
by Trend® Windows & Doors in writing, are strictly prohibited. Patents and Design Registrations pending.
18Trend thermAL® Awning Window | TAA | Mk-1 | 30 Nov 2012
Trend thermAL® Awning Window | Awning/Fixed/Awning with Low Lite - Double Glazed
OUTSIDE
F
F
F FF F F
OUTSIDE
JAMB
F
MULLION
JAMB
MULLION
OUTSIDE
OUTSIDE
5526
5364
34 9
92
52
319
5352.8
12.5
JAMB
MULLION
JAMB
MULLION
3130
713434
31
71
31 31
2655