4

HYBRIS is a new insulation material for timber frame or masonry walls, pitched roofs or ceiling applications.

AN INNOVATIVE TECHNOLOGY

DUAL PERFORMANCE

HYBRIS is a reflective insulation product based on a honeycomb structure made of shaped polyethylene foams glued to aluminium coated polyethylene foils.

High thermal performance is provided by a special structure composed of a large number of low emissivity cavities, protected from dust and excessive air movement. Moreover, the low emissivity external films provide additional thermal resistance, when associated with air cavities.

Hybris is available in 1200mm wide rolls and in a range of thicknesses from 45mm to 165mm* every 15mm. 18 rolls per pallet.

* 150mm and 165mm available in June 2014

With a core effective thermal conductivity ( t, according to EN 12667 Annex A) as low as 0,033 W/m.K, HYBRIS provides a thermal resistance as high as R=5.00m2.K/W.

With an air gap on either side, HYBRIS can reach on average an additional thermal resistance per air gap of up to 0,67m2.K/W in walls (horizontal flow) and up to 0.45m2.K/W in roofs (upward vertical flow) which can be incorporated into U value calculations carried out in accordance with EN 6946.

5

SPACE SAVING

FULLY CERTIFIED

HYBRIS insulation helps to keep the fabric element to a minimum thickness and saves space !

With 105 mm and 2 air gaps, in walls HYBRIS can achieve an R-value as high as 4,35m2.K/W !

With the additional resistance due to the air gaps it is possible to reduce the thickness of the material needed and consequently save money.

HYBRIS has been tested according to the following EN standards :

• EN 12667: «Thermal performance of building materials - Determination of thermal resistance – Heat flow meter method - Products of high and medium thermal resistance»

• EN ISO 6946: «Building components and building elements Thermal resistance and thermal transmittance - Calculation method»

HYBRIS helps to meet the requirements of Approved Document L 2010 (England & Wales) and Section 6 (Scotland). NHBC accepted when used in accordance with the manner described in the certification.

AIRTIGHT

HYBRIS is intrinsically airtight, stopping air infiltration from the outside and heat loss through convection from the inside

USER FRIENDLY

HYBRIS is very light – less than 16Kg/m3 – thus easy to carry

• HYBRIS is classified A+ for internal air quality according to ISO 16000

• HYBRIS is clean - does not generate dust or fibre

VAPOUR TIGHT

HYBRIS is intrinsically resistant to water vapour.

QUICK AND EASY TO INSTALL

FLEXIBLE

HYBRIS is very easy to cut, manually with an insulation knife on a flat surface or with an electrical saw.

HYBRIS is easily installed between rafters, timber studs or within floor joists. It accurately fits all widths, held in place by compression. HYBRIS does not slump down.

HYBRIS reduces the installation time without changing installation procedures.

HYBRIS is fully certified by the accredited body, VTT

HYBRIS has a European Technical Agreement N°13/0121

6

PRODUCT

PACKAGING

THICKNESS LENGTH WIDTH ROLL AREA PALET AREA

45mm 5.75m

1200mm

6.90m2 124,200m2

60mm 4.78m 5.73m2 103,248m2

75mm 4.01m 4.81m2 86,616m2

90mm 3.57m 4.28m2 77,112m2

105mm 3.13m 3.75m2 67,608m2

120mm 2.73m 3.27m2 58,968m2

135mm 2.51m 3.01m2 54,216m2

150mm* 2.40m 2.88m2 51,840m2

165mm* 2.25m 2.70m2 48,600m2

PROPERTY TEST METHOD DECLARED VALUEThickness EN 823 45 to 165mm* every 15 mm

Weight/m3 EN 1602 50 kPa

Transversal direction >40 kPa

RESISTANCE TO TEARING, NAIL SHANK

Longitudinal directionEN 12310-1part1

>150 N

Transversal direction >150 N

PEEL STRENGTH OF TAPE EN 11339 22 N/100mm

TENSILE STRENGTH PARALLEL TO FACES OF THE TAPE EN 1608 116 N/100mm

WATER VAPOUR TRANSMISSION

Permeability (W)

EN 12572 set C

1100 MNs/g

Diffusion eq.air layer thickness (Sd) >200m

WATERTIGHTNESS Watertight, W1

AIR PERMEABILITY Airtight

FIRE RESISTANCE Class F

AFTER AGEING

TENSILE STRENGTH

Longitudinal directionEN 1608

>50 kPa

Transversal direction >50 kPa

RESISTANCE TO TEARING, NAIL SHANK

Longitudinal directionEN 12310-1 part1

>150 N

Transversal direction >150 N

PEEL STRENGTH OF TAPE EN 11339 At 98 N/100mm, the HYBRIS surface is torn

TENSILE STRENGTH PARALLEL TO FACES OF THE TAPE EN 1608 132 N/100mm

FIRE RESISTANCE Class F

HYBRIS PROPERTIES

* Available in June 2014

7

IN WALLS

IN ROOFS

Details of the calculated configuration:• Air cavities: 25mm• Low emissivity (int / ext):

0.05 / 0.10• Heat flow direction: horizontal• Temperature difference

(Tint / Text): 20°C / 0°C• HYBRIS core thermal resistance

according to ETA n°13/0121• Thermal performance of air gaps

according to EN 6946.

Details of the calculated configuration:• Air cavities: 20mm• Low emissivity (int / ext): 0.05 / 0.10• Heat flow direction: upward vertical flow• Temperature difference (Tint / Text): 20°C / 0°C• HYBRIS core thermal resistance according to

ETA n°13/0121• Thermal performance of air gaps according

to EN 6946.

Declared Thermal Resistance (m2.K/W) When using foil backed plasterboard

THICKNESS CORE R-VALUER-VALUE WITH 1 AIR GAP**

R-VALUE WITH 2 AIR GAPS CORE +2 AG*

45mm 1.35 1.95 2.55 2.65

60mm 1,80 2.45 3.00 3.10

75mm 2.25 2.90 3.45 3.55

90mm 2.70 3.35 3.90 4.00

105mm 3.15 3.80 4.35 4.45

120mm 3.60 4.25 4.80 4.90

135mm 4.05 4.70 5.25 5.35

150mm* 4.50 5.15 5.70 5.80

165mm* 5.00 5.65 6.20 6.30

Declared Thermal Resistance (m2.K/W)

THICKNESS CORE R-VALUER-VALUE WITH 1 AIR GAP**

R-VALUE WITH 2 AIR GAPS***

45mm 1.35 1.80 2.20

60mm 1.80 2.20 2.65

75mm 2.25 2.65 3.10

90mm 2.70 3.10 3.55

105mm 3.15 3.55 4.00

120mm 3.60 4.00 4.45

135mm 4.05 4.45 4.90

150mm* 4.50 4.90 5.35

165mm* 5.00 5.40 5.85

HYBRIS THERMAL PERFORMANCE

* Available in June 2014

** warm side *** 1 side unventilated, 1 side ventilated

* Available in June 2014

** warm side