of 68
7/28/2019 Hydra Shock
1/68
7/28/2019 Hydra Shock
2/68
7/28/2019 Hydra Shock
3/68
SECTION 1
General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Change Out Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . 3
Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Placement Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SECTION 2
Service Safety Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Shop Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Cleaning Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
E q u i p m e n t . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Thread Galling Cautions . . . . . . . . . . . . . . . . . . . . . . . . . 8
To Break A Stuck Connection . . . . . . . . . . . . . . . . . . . . . . 8
SECTION 3
D i s a s s e m b l y . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Disassembled Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
SECTION 4
Inspection Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Incoming Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . 22
C l e a n i n g . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2
Inspection Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Magnetic Particle Inspection Guideline . . . . . . . . . . . . . . . . 23
Chrome Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Hardbanded Surfaces . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Part Inspection Guidelines . . . . . . . . . . . . . . . . . . . . . . . 24
Critical Parts Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Critical Length Tolerance. . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Seal Assembly Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Seal Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Seal Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Seal Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 0
SECTION 5
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Torque Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
SECTION 6
Testing Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Drive Section & Spring Section Pressure Test . . . . . . . . . . . . . 49
Internal Diameter Pressure Test . . . . . . . . . . . . . . . . . . . . 50
Spring Compression Test . . . . . . . . . . . . . . . . . . . . . . . . 51
E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 H Y D R A - S H O C K
M o d e l B T o o l
O p e r a t i o n & S e r v i c e M a n u a l
TABLE OF CONTENTS
7/28/2019 Hydra Shock
4/68
Smith Services-HE Group
Tool Service Report. . . . . . . . . . . . . . . . . . . . . . . . . . . 52
SECTION 7Shipping Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
SECTION 8
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
SECTION 9
Fishing Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Fishing Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 H Y D R A - S H O C K
M o d e l B T o o l
O p e r a t i o n & S e r v i c e M a n u a l
The last page of manual is 61.
TABLE OF CONTENTS
7/28/2019 Hydra Shock
5/68
SECTION 1
FIG. 1 Slick Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
FIG. 2 Pendulum Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . 5
FIG. 3 Pendulum Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . 5
FIG. 4 Mild to Medium Packed Assembly. . . . . . . . . . . . . . . . . . . 5
FIG. 5 Severe Packed Assembly . . . . . . . . . . . . . . . . . . . . . . . . 5
SECTION 2
FIG. 6 Service Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
FIG. 7 Tapping Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
SECTION 3
FIG. 8 The Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
FIG. 9 Removal Of Fill And Service Plugs. . . . . . . . . . . . . . . . . . 10
FIG. 10 Removal Of Oil From Spring Cylinder . . . . . . . . . . . . . . . 11
FIG. 11 Top Sub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
FIG. 12 Equalizer Mandrel . . . . . . . . . . . . . . . . . . . . . . . . . . 13
FIG. 12 A Seal Retainer & Wave Disc Spring . . . . . . . . . . . . . . . . 13
FIG. 13 Equalizer Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . 14
FIG. 14 Balance Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
FIG. 14A Floating Piston . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
FIG. 15 Spring Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
FIG. 16 Spring Mandrel, Load Washer, Belleville Disc Springs,
Load Washer . . . . . . . . . . . . . . . . . . . . . . . . 17
FIG. 17 Connector Mandrel . . . . . . . . . . . . . . . . . . . . . . . . . 18
FIG. 18 Drive Pin Retainer Sub (DPRS) . . . . . . . . . . . . . . . . . . . 19FIG. 19 Dravie Shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
FIG. 19 A Wear Sleeves . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
SECTION 4
FIG. 20 Super Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
SECTION 5
FIG. 21 Drive Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
FIG. 22 Drive Shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
FIG.23 Drive Pins. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
FIG. 24 Drive Pin Retainer Sub (DPRS) . . . . . . . . . . . . . . . . . . . 36
FIG. 25 Connector Mandrel . . . . . . . . . . . . . . . . . . . . . . . . . 37FIG. 26 Load Washer & Belleville Disc Springs . . . . . . . . . . . . . . . 38
FIG. 26A Spring Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
FIG. 27 Spring Mandrel . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
FIG. 28 Spring Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
FIG. 29 Balance Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
FIG. 30 Floating Piston . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
FIG. 31 Equalizer Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . 43
E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 H Y D R A - S H O C K
M o d e l B T o o l
O p e r a t i o n & S e r v i c e M a n u a l
List of Figures
7/28/2019 Hydra Shock
6/68
FIG. 32 Equalizer Mandrel . . . . . . . . . . . . . . . . . . . . . . . . . . 44
FIG. 33 Seal Retainer & Wave Disc Spring . . . . . . . . . . . . . . . . . 45
FIG. 34 Top Sub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
FIG. 35 Assembly Torque Check. . . . . . . . . . . . . . . . . . . . . . . 47
SECTION 6
FIG. 36 Drive Section & Spring Section Pressure Test . . . . . . . . . . . 49
FIG. 37 Internal Diameter Pressure Test . . . . . . . . . . . . . . . . . . . 50
FIG. 38 Spring Compression Test . . . . . . . . . . . . . . . . . . . . . . 51
E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 H Y D R A - S H O C K
M o d e l B T o o l
O p e r a t i o n & S e r v i c e M a n u a l
List of Figures
7/28/2019 Hydra Shock
7/68
Table 1 Engineering Specifications . . . . . . . . . . . . . . . . . . . . . . 2
Table 2 Change Out Recommendations . . . . . . . . . . . . . . . . . . . . 3
Table 3 Individual Spring Height . . . . . . . . . . . . . . . . . . . . . . 25
Table 4 Wear Down Thickness . . . . . . . . . . . . . . . . . . . . . . . . 26Table 5 O.D. Wear Down Tolerances . . . . . . . . . . . . . . . . . . . . 26
Table 6 Shoulder Standoff . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Table 7 Makeup Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Table 8 Makeup Torque for Fill and Service Plugs . . . . . . . . . . . . . 48
Table 9 Spring Compression Test . . . . . . . . . . . . . . . . . . . . . . 51
E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 H Y D R A - S H O C K
M o d e l B T o o l
O p e r a t i o n & S e r v i c e M a n u a l
List of Tables
7/28/2019 Hydra Shock
8/68
SECTION 1
General Description
During drilling operations, various dynamic impact loads are impartedfrom the drill bit to the drill string. These loads, which are cyclical innature, may lead to many problems:
Premature failure of the drill string and rig equipment
Low penetration rates
Hole problems
The HYDRA-SHOCK Model B tool is designed to absorb and dampen
the variable axial dynamic loads produced by a drill bit during normaldrilling operations. Unlike other tools on the market, the HYDRA-SHOCK Model B tool is fully compensated for both pump pressure,which has a tendency to open the tool, and hydrostatic pressure, which hasa tendency to close the tool. Consequently, as dynamic impact loads aretransferred from the bit to the drill string, the tool, which is in a hydrauli-cally neutral position, readily dampens the loads without the additionaltask of overcoming any pressure differentials. Additionally, the toolsstroke length and low spring rate make it active over a much greater rangeof operation. As a result, the penetration rate and bit life are greatly im-proved.
As axial loads are produced, energy absorption is accomplished throughthe use of a spring element; force dampening is accomplished through theuse of fluid and mechanical friction; and pressure compensation is accom-plished through the use of a fluid transfer system. These three elements arethe heart of the tool.
E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 1 H Y D R A - S H O C K M o d e l B T o o lO p e r a t i o n & S e r v i c e M a n u a l
7/28/2019 Hydra Shock
9/68
Operation
As a tri-cone bit rotates, it produces a pattern on the bottom of the bore-hole which consists of peaks and valleys. With each revolution of thebit, the cones will tend to follow the sinusoidal contour of the bottom of
the borehole producing a cyclical oscillation of the drill string. Thesprings in the HYDRA-SHOCK Model B tool, normally used to keepthe tool extended, are compressed and absorb the shock load produced bythe bit cones as they progress through one of the peaks.
Additionally, the load is dissipated by fluid friction created when oil ismetered through the spring stack and by mechanical friction resulting fromthe movement of the spring stack. When the bit cones move into a val-ley, the HYDRA-SHOCK Model B tools springs will extend the toolto its normal position. These two combined actions isolate the axial loadspresent during the drilling operation and maintain a near constant weight-on-bit when the tool is run within its operational load limits.
Maximum shock absorption is achieved by placing the HYDRA-SHOCKModel B tool as close to the bit as possible. Care should be taken to en-sure that the tool is never run in the neutral zone, in tension, or in over-sized boreholes (hole sizes greater than 2 times the OD of the tool).
The engineering specifications for the HYDRA-SHOCK Model B tool canbe found in Table 1.
Tool O.D.
inches (mm)
6-3/4
(171)
8-1/2
(216)
11-1/4
(286)Tool I.D.
inches (mm)2-13/16
(71)3
(76)3
(76)
OALfeet inches (mm)
19' 10-1/4"(6 052)
23' 2-3/16"(7 066)
22' 7-41/64"(6 900)
StrokeMax. Deflectioninches (mm)
4-1/2(114)
5-1/4(133)
7-1/4(184)
Minimum RecommendedWorking Load lbf (N)
10,000(44 480)
10,000(44 480)
10,000(44 480)
Maximum RecommendedWorking Load lbf (N)
60,000(270 000)
85,000(380 000)
85,000(380 000)
Tensile Yield Load
lbf (N)
629,000
(2 800 000)
1,200,000
(5 000 000)
2,500,000
(11 000 000)Yield Torque
lbfft (Nm)38,000
(52 000)71,000
(96 000)201,000
(273 000)
Maximum TemperatureF (C)
400 F
(204 C)
400 F
(204 C)
400 F
(204 C)
Spring Ratelbf/in (N/m)
13,000(2 300 000)
16,800(2 900 000)
12,500(2 200 000)
H Y D R A - S H O C K M o d e l B T o o l 2 E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 O p e r a t i o n & S e r v i c e M a n u a l
SECTION 1
Engineering Specifications
Table 1
( m e t r i c )
7/28/2019 Hydra Shock
10/68
Change Out Recommendations
The HYDRA-SHOCK should be changed out, periodically, for servicing.See Table 2, Change Out Recommendations, to determine recommendedhours of use before servicing.
Follow the step below to use the information in Table 2, Change Out Rec-ommendations.
Step 1. Select the Tool OD.
Step 2. Determine the drilling USAGE.
Step 3. Select the hole size and note the corresponding hours.
Step 4. Determinethe bottomhole temperature andnote thecorresponding hours.
Step 5. Compare the hours between the temperature and the drilling USAGE.
Step 6. The smaller of the two will determine the service period.
Tool ODinches (mm)
6-3/4(171)
8-1/2(216)
11-1/4(286)
USAGE Hole Size Hours Hole Size Hours Hole Size Hours
Rotating inStraight orHorizontal
Section Only
7-7/8(200)8-3/4(222)9-7/8
(251)
400
400
300
9-7/8(250)
12-1/4(311)
17-1/2
(445)
400
353
250
17-1/2(445)
20(508)
26
(660)
400
350
300
Rotating inDeviated or
Build Section
8-3/4(222)9-7/8(251)
12-1/4(311)
200
200
200
9-7/8(251)
12-1/4(311)
17-1/2(445)
250
150
100
17-1/2(445)
20(508)
26(660)
300
350
200
Bottom HoleTemperture
Hours
100-200 F
38-93 C400 400 400
200-300F
93-148 C300 300 300
300-400 F148-204 C
300 300 300
400-500 F
204-260 C150 150 150
E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 3 H Y D R A - S H O C K M o d e l B T o o lO p e r a t i o n & S e r v i c e M a n u a l
Change Out Recommendations
Change Out Recommendations
Table 2
7/28/2019 Hydra Shock
11/68
Placement
The HYDRA-SHOCK Model B Tool is most effective when placed di-rectly above the bit. Like other vibration dampeners, the HYDRA-SHOCK Model B tool is less stiff than a drill collar of the same OD.
Depending on the placement of the tool, the reduced stiffness can compro-mise the performance of the bottom hole assembly. Also, if improperlyplaced in the bottom hole assembly, high stresses could reduce tool per-formance and life. General guidelines for tool placement are as follows:
In a slick bottom hole assembly, place the tool above the bit, as
shown in FIG. 1.
For a pendulum assembly used in very mild crooked tendencies,
the tool can be placed directly above the bit, as shown in FIG. 2.
For pendulum assemblies used where there are crooked hole ten-
dencies, it is recommended that the tool be placed directly abovethe first (fulcrum) stabilizer, as shown in FIG. 3. In addition, a sec-
ond stabilizer should be placed one drill collar up from the tool.
This will help reduce stresses in the tool due to lateral loads.
In packed bottom hole assemblies, it is recommended that the tool
be placed above the second zone of stabilization, as shown in FIG.
4. Avoid using the tool as a short drill collar since the reduced stiff-
ness will compromise bottom hole assembly performance and in-
crease bending stresses in the tool.
When crooked hole tendencies are severe, it is recommended that
the tool be placed above the third zone of stabilization, as shown inFIG. 5. It is also recommended that an additional stabilizer be
placed one drill collar above tool to reduce lateral loading.
H Y D R A - S H O C K M o d e l B T o o l 4 E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 O p e r a t i o n & S e r v i c e M a n u a l
SECTION 1
7/28/2019 Hydra Shock
12/68
Placement Diagram
E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 5 H Y D R A - S H O C K M o d e l B T o o lO p e r a t i o n & S e r v i c e M a n u a l
Placement
Slick
Assembly
FIG. 1
Pendulum
Assembly
FIG. 2Pendulum
Assembly
FIG. 3
Mild to
Medium
Packed
Assembly
FIG. 4
Severe
Packed
Assembly
FIG. 5
D r i l l
C o l l a r s
S t a b i l i z e r
D r i l l
C o l l a r s
D r i l l
C o l l a r s
D r i l l
C o l l a r s
D r i l l
C o l l a r s
H Y D R A - S H O C K
M o d e l B T o o l
H Y D R A - S H O C K
M o d e l B T o o l
H Y D R A - S H O C K
M o d e l B T o o l
H Y D R A - S H O C K
M o d e l B T o o l
H Y D R A - S H O C K
M o d e l B T o o l
S t a b i l i z e r
S t a b i l i z e r
S t a b i l i z e r
S t a b i l i z e r
S t a b i l i z e r
S t a b i l i z e r
S t a b i l i z e r
S t a b i l i z e r s
D r i l l
C o l l a r
D r i l l
C o l l a r
D r i l l
C o l l a r
S h o r t
D r i l l
C o l l a r
S h o r t
D r i l l
C o l l a r
D r i l l
C o l l a r
7/28/2019 Hydra Shock
13/68
SECTION 2
Service Safety Procedures
Tools Reference Manuals
TIC Accelerator Tool Manual No. 2-35
ACCD & ACCM Fishing Accelerators Tool Manual No. 2-20
Magnum Drilling Up:Accelerator Manual No. 2-60
TT Accelerator Tool Manual No. 2-58
V1 Accelerator Tool Manual No. 6-90
Check tool for serial number and type identification to determine whetherthe tool is filled with nitrogen (as noted above). Caution-All nitrogen filled
tools must be degassed before service. Once determined, immediately re-fer to applicable service manual.
Caution-All tools have the potential to retain hydrostatic pressure. Allfill/vent plugs are to be removed before servicing
Any person responsible for servicing of HE Group tools shall be fullyknowledgeable concerning all safety procedures and require all servicepersonnel to be thoroughly trained in safe procedures as set forth in SmithServicesHE Group service manuals and Tool Service Courses.
Any additional information concerning tools or equipment may be ob-tained by contacting:
SII Smith ServicesHE GroupP.O. Box 60068Houston, TX 77205-0068
Telephone 281-443-3370
H Y D R A - S H O C K M o d e l B T o o l 6 E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 O p e r a t i o n & S e r v i c e M a n u a l
7/28/2019 Hydra Shock
14/68
Shop Service
Cleaning and servicing should occur as soon as possible after tool is usedin the hole.
Cleaning Procedures1. Water soak tool to remove dried, caked mud.
2. Use steam and a strong biodegradable cleaner to remove oil and
grease.
3. Allow steam cleaned parts to dry and cool before disassembling tool.
Equipment
Service equipment needed to disassemble, assemble, and test theHYDRA-SHOCK Model B tool, is shown in FIG. 6.
E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 7 H Y D R A - S H O C K M o d e l B T o o lO p e r a t i o n & S e r v i c e M a n u a l
Shop Service
FIG. 6Service Equipment
7/28/2019 Hydra Shock
15/68
Thread Galling Cautions
Galling can be caused by:
Dirty or damaged threads and/or thread shoulders.
Threads and shoulders that are not completely covered with thread
lubricant before assembly.
Misaligned connections during assembly or disassembly.
Applying a bending load when torquing the connection duringassem-
bly or disassembly.
Leakage which would allow the connection to become dry or filled
with abrasive matter.
Steps to prevent galling:
Clean and dry connection threads and shoulders thoroughly.
Apply thread lubricant evenly over threads and shoulders.
Position the backup device and breakout device as shown in disas-
sembly and assembly sections.
Support and tie down the appropriate parts with a hold down steady
rest as described in Disassembly and Assembly.
Torque connection properly, to the recommended make-up torque.
To Break A Stuck Connection
Tap the outside surface of the connection with a hammer while slowly un-
screwing the part. It may be helpful to work the connection out by alternatelytightening and untightening the part several times, FIG. 7.
If such methods fail, one part of the connection can sometimes be ma-chined away in an attempt to salvage the other.
Ultimately, the connection can be forced apart. This may scrap both parts.
H Y D R A - S H O C K M o d e l B T o o l 8 E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 O p e r a t i o n & S e r v i c e M a n u a l
SECTION 2
EXTERNALPARTS
BackupDevice
BreakoutDevice
TAP WITH HAMMER INTHESE AREAS
BackupDevice
BreakoutDevice
INTERNALPARTS
Sub
Cylinder
SubMandrel
Mandrel
FIG. 7Tapping Locations
7/28/2019 Hydra Shock
16/68
SECTION 3
Disassembly
Disassembly takes place after tool has been cleaned. This section is applicable toright-hand threaded tools. Text and graphics depict automated breakout unit.
E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 9 H Y D R A - S H O C K M o d e l B T o o lO p e r a t i o n & S e r v i c e M a n u a l
SECTION 3
Disassembly
Disassembly takes place after tool has been cleaned. This section is applicable toright-hand threaded tools. Text and graphics depict automated breakout unit.
The Tool
Check serial number to verify that the tool is a HYDRA-SHOCKModel B.
Place tool in test rack with test subs.
Perform incoming report and record results on Smith Services-HEGroup Services Report.
Place the tool on an Oil Drip Tray as shown in FIG. 8.
Critical Factors
& Safety Notes
Shop Service - DISASSEMBLY
Description & Sequence
FIG. 8
7/28/2019 Hydra Shock
17/68
H Y D R A - S H O C K M o d e l B T o o l 10 E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 O p e r a t i o n & S e r v i c e M a n u a l
SECTION 3
Removal Of Fill And Service PlugsAlways use safety procedures when removing the fill plugs, as toolmay have developed pressure inside while downhole.
Use proper size hex wrenches to remove fill plugs. Drill out plug ifit cannot be removed with hex wrench.
Critical Factors& Safety Notes
CautionCylinder may have in-ternal pressure.
Do not expose handsor any other part ofthe body to escapingfluid.
Wear appropriate eyeprotection.
Shop Service - DISASSEMBLYDescription & Sequence
FIG. 9
7/28/2019 Hydra Shock
18/68
E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 11 H Y D R A - S H O C K M o d e l B T o o lO p e r a t i o n & S e r v i c e M a n u a l
Disassembly
Removal Of Oil From Spring Cylinder
Connect air to the drive cylinder as shown in FIG. 10.
Rotate the tool until the balance cylinder fill hole faces down intothe oil drip tray.
Apply minimum air pressure.
Expelled oil may be filtered and reused.
Caution
Wear appropriate eyeprotection.
Critical Factors& Safety Notes
Shop Service - DISASSEMBLYDescription & Sequence
FIG. 10
7/28/2019 Hydra Shock
19/68
H Y D R A - S H O C K M o d e l B T o o l 12 E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 O p e r a t i o n & S e r v i c e M a n u a l
SECTION 3
Top SubClamp backup device onto equalizer cylinder as shown in FIG. 11.
Clamp breakout device on top sub and apply sufficient torque tobreak out the connection.
Record torque on Smith Services-HE Group Service Report.
CautionDo not stand in frontof backup device orbreakout device whenapplying torque to thetool connection.
Do not over clamp.
Do not clamp in centerof cylinder.
Critical Factors& Safety Notes
Shop Service - DISASSEMBLYDescription & Sequence
FIG. 11
7/28/2019 Hydra Shock
20/68
E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 13 H Y D R A - S H O C K M o d e l B T o o lO p e r a t i o n & S e r v i c e M a n u a l
Disassembly
Equalizer Mandrel
With backup device on equalizer cylinder, clamp breakout deviceon equalizer mandrel, as shown in FIG. 12.
Apply sufficient torque to breakout the connection.
Record torque on Smith Services-HE Group Service Report.
Seal Retainer & Wave Disc Spring
Remove equalizer mandrel from breakout device. Remove wavedisc spring and seal retainer from equalizer mandrel, as shown in
12A.
Caution
Do not stand in frontof backup device orbreakout device whenapplying torque to thetool connection.
Do not damagechrome.
Do not over clamp.
Do not damage pistonseals with box thread.
Critical Factors& Safety Notes
Shop Service - DISASSEMBLYDescription & Sequence
FIG. 12
FIG. 12 A
7/28/2019 Hydra Shock
21/68
H Y D R A - S H O C K M o d e l B T o o l 14 E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 O p e r a t i o n & S e r v i c e M a n u a l
SECTION 3
Equalizer CylinderClamp backup device onto balance cylinder, see FIG. 13.
Clamp breakout device onto equalizer cylinder.
Apply sufficient torque to breakout the connection.
Record torque on Smith Services-HE Group Service Report.
Remove equalizer cylinder.
CautionDo not stand in frontof backup device orbreakout device whenapplying torque to thetool connection.
Do not over-clamp.
Do not clamp in cen-ter of cylinder.
Critical Factors& Safety Notes
Shop Service - DISASSEMBLYDescription & Sequence
FIG. 13
7/28/2019 Hydra Shock
22/68
E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 15 H Y D R A - S H O C K M o d e l B T o o lO p e r a t i o n & S e r v i c e M a n u a l
Disassembly
Balance Cylinder
Clamp backup device onto spring cylinder as shown in FIG. 14.
Clamp breakout device onto balance cylinder.
Apply sufficient torque to break the connection.
Record torque on Smith Services-HE Group Service Report.
Floating Piston
With balance cylinder in breakout device, remove floating pistonusing aluminum or brass bar as shown in FIG.14A.
Caution
Do not stand in front ofbackup device orbreakout device whenapplying torque to thetool connection.
Do not over-clamp.
Do not clamp in centerof cylinder.
Critical Factors& Safety Notes
Shop Service - DISASSEMBLYDescription & Sequence
FIG. 14
FIG. 14A
7/28/2019 Hydra Shock
23/68
H Y D R A - S H O C K M o d e l B T o o l 16 E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 O p e r a t i o n & S e r v i c e M a n u a l
SECTION 3
Spring Cylinder
Clamp backup device onto Drive Pin Retainer Sub (DPRS), as shown inFIG. 15.
Clamp breakout device onto spring cylinder.
Apply sufficient torque to break the connection.
Record torque on Smith Services-HE Group Service Report.
Remove spring cylinder.
Caution
Do not stand in frontof backup device orbreakout device whenapplying torque to thetool connection.
Critical Factors& Safety Notes
Shop Service - DISASSEMBLYDescription & Sequence
FIG. 15
7/28/2019 Hydra Shock
24/68
E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 17 H Y D R A - S H O C K M o d e l B T o o lO p e r a t i o n & S e r v i c e M a n u a l
Disassembly
Spring Mandrel
Load Washer, Belleville Disc Springs & Second Load Washer
With backup device on drive pin retainer sub (DPRS), clamppower tong on spring mandrel as shown in FIG. 16.
Support spring mandrel, as shown in FIG. 16.
Apply sufficient torque with power tong to breakout theconnection.
Record torque on Smith Services-HE Group Service Report.
Remove load washer, Belleville Disc Springs, then second load
washer from spring mandrel.
Critical Factors& Safety Notes
Shop Service - DISASSEMBLYDescription & Sequence
FIG. 16
Caution
Do not stand in frontof backup device orbreakout device whenapplying torque to thetool connection.
Do not over-clamp.
Do not scratch chromeon spring mandrelshaft.
Do not bend springmandrel.
7/28/2019 Hydra Shock
25/68
H Y D R A - S H O C K M o d e l B T o o l 18 E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 O p e r a t i o n & S e r v i c e M a n u a l
SECTION 3
Connector Mandrel
With DPRS in backup device, clamp breakout device onconnector mandrel as shown in FIG. 17.
Apply sufficient torque to breakout the connection.
Record torque on Smith Services-HE Group Service Report.
Caution
Do not stand in frontof backup device orbreakout device whenapplying torque to thetool connection.
Critical Factors& Safety Notes
Shop Service - DISASSEMBLYDescription & Sequence
FIG. 17
7/28/2019 Hydra Shock
26/68
E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 19 H Y D R A - S H O C K M o d e l B T o o lO p e r a t i o n & S e r v i c e M a n u a l
Disassembly
Drive Pin Retainer Sub (DPRS)
Clamp backup device onto drive cylinder, see FIG. 18.
Clamp breakout device on DPRS.
Apply sufficient torque to break out the connection and removeDPRS.
Record torque on Smith Services-HE Group Service Report.
Caution
Do not stand in frontof backup device orbreakout device whenapplying torque to thetool connection.
Critical Factors& Safety Notes
Shop Service - DISASSEMBLYDescription & Sequence
FIG. 18
7/28/2019 Hydra Shock
27/68
H Y D R A - S H O C K M o d e l B T o o l 20 E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 O p e r a t i o n & S e r v i c e M a n u a l
SECTION 3
Drive Shaft
Clamp backup device on drive shaft, as shown in FIG. 19.
Clamp breakout device onto drive cylinder.
Pull drive shaft through the drive cylinder.
Remove drive pins.
Wear Sleeves
With drive cylinder in breakout device, remove wear sleeves from
drive cylinder as shown in FIG. 19A.
Critical Factors& Safety Notes
Shop Service - DISASSEMBLYDescription & Sequence
FIG. 19
Caution
Do not stand in frontof backup device orbreakout device whenapplying torque to thetool connection.
FIG. 19 A
7/28/2019 Hydra Shock
28/68
Disassembled Tool
Below is a schematic of the HYDRA-SHOCK Model B tool after disas-sembly.
E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 21 H Y D R A - S H O C K M o d e l B T o o lO p e r a t i o n & S e r v i c e M a n u a l
Disassembly
7/28/2019 Hydra Shock
29/68
SECTION 4
Inspection Procedures
Inspection should occur as soon as possible after tool is used. Replace partswhich do not comply to an acceptable condition. No machining or rework-ing is to be performed without Smith ServicesHE Group's approval.
Incoming Inspection
Visually inspect for damage to the external members and note ab-
normal wear or markings.
Check for Hydrogen Sulfide residue with Lead Acetate Tape.
Place tape strips at all ports and vents were the tape can come in
contact with the well fluids left in the tool. If a positive indication isnoted, special treatment of the part is required.
Cleaning
1. Water soak tool parts to remove dried, caked mud.
2. Use steam and a strong biodegradable cleaner to remove oil and grease.
3. Allow steam cleaned parts to dry and cool before inspecting tool.
Inspection Procedures
Inspect all parts, using the steps below, each time the tool is disassembled.
Inspect all rotary shouldered connections per API. Inspection pro-cedures will meet the applicable contentof API RP 7G, Section 12.
Inspect all make up shoulders and faces for galling and wash. Re-
pair or replace part as needed.
Use the Part Inspection Guideline for individual parts. Repair or
replace part if condition noted in guideline exist.
Use Magnetic Particle Inspection Guidelines for Magnetic Parti-
cle Inspection of parts.
Check all external parts for wear down. Replace part when the OD
wear is at or below the diameters listed in Table 5.
Heavy grooves or junk cuts that exceed minimum wear down are
not acceptable.
Multiple grooves or cuts are in a small area are not acceptable.
Use Critical Parts Inspection form to record part condition, part
diameters, and results from magnetic particle inspection.
H Y D R A - S H O C K M o d e l B T o o l 22 E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 O p e r a t i o n & S e r v i c e M a n u a l
7/28/2019 Hydra Shock
30/68
Use Fishing Dimensions for length, ID, and OD comparison. Re-
cord findings on Critical Length Tolerance form.
Use Chrome Guidelines to inspect chrome.
Magnetic Particle Inspection Guideline
Refer to API RP 7G for guidelines. Subject critical stress areas to Mag-netic Particle Inspection at each service. Replace parts if indication isfound and cannot be removed by acceptable practice.
A characteristic of industrial hard chrome is micro cracking. Micro crack-ing does not pose a problem or threat of failure to the part. Typical microcracking should not constitute criteria for rejecting a part.
Critical Stress Areas
Pin connections plus 1" (25 mm) beyond the shoulder or end of the
thread.
External component box connections (inside and outside) plus1" (25 mm) beyond the connection.
Internal component box connections (inside and outside) and all
grooves up to the end of the last groove or end of the relief or
make-up face.
Fill plug holes, service plug holes, ports, vents, slots, and
2" (51 mm) either side.
Large diameter changes plus 4" (102 mm) either side.
Chrome Guidelines
Record condition of chrome area on Critical Parts Inspection form. Thefollowing guidelines may be tempered based on knowledge and experi-ence for a given area and environment tools will be utilized.
Hydraulic Fluid Seal Area
Pits in chrome
The maximum acceptable pit diameter is 1/8" (3 mm).
The maximum acceptable pit depth is 1/64" (0.5 mm).
Multiple pits must be at least 3/8" (10 mm) apart.
A maximum of 3 pits ina 1" x 1" (25 mmx 25 mm)square area are
acceptable.
Chipped chrome
Missing or chipped chrome is not acceptable.
It is acceptable for chrome outside of the seal area to be pitted, missing, orchipped. Dress and remove sharp edges from these areas.
E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 23 H Y D R A - S H O C K M o d e l B T o o lO p e r a t i o n & S e r v i c e M a n u a l
Inspection Procedures
7/28/2019 Hydra Shock
31/68
7/28/2019 Hydra Shock
32/68
Springs
a. Twenty-five percent of the springs should be subjected to mag-
netic particle inspection (MPI). During the MPI, the coils should be
positioned such that the inspector can check for cracks propagating
circumferentially on the I.D. and O.D. surfaces as well as for cracks
propagating radially from the I.D. of the part towards the O.D. of thepart. If cracks or other improprieties are found in one (1) spring, all
springs in the spring stack shall be subjected to MPI testing.
b. Springs that have cracks or other improprieties should be discarded.
c. Measure 25% of the springs, to determine if there are any changes in
overall height. Height variations greater than those specified in Table
3 found in one (1) spring shall necessitate the measurement of all
springs.
ToolO.D.
Initial StackHeight
Allowable Decrease InSpring Height
6-3/4(171)
.0407(10.33)
.008(0.203)
8-1/2(216)
0.515(13.08)
11-1/4(286)
0.685(17.39)
Springs with a decrease in overall height greater than that specified
should not be used without consulting the engineering department.
Connector Mandrel
a. Visually check threads for washout, galling, or deformation.
Drive Pin Retainer Sub
a. Inspect threads for washout, rust and galling.
Drive Pins
a. Check Drive Pins for excessive wear. Wear on the length and O.D. must
not exceed 1/16" (1.6 mm).
b. Pins may be reused if there are light scratches on surface; however,
pins that are severely deformed must be replaced.
Drive Cylinder
a. Visually inspect threads for washout and galling.
b. Check seal area I.D.for wear +1/16" (1.6 mm) abovenominal dimension.
c. Check splines for excess wear. Inspect for cracks and deformation.
E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 25 H Y D R A - S H O C K M o d e l B T o o lO p e r a t i o n & S e r v i c e M a n u a l
Inspection Procedures
Individual Spring Height
inches (mm)
Table 3
7/28/2019 Hydra Shock
33/68
Wear Sleeve
a. The minimum allowable thickness for each size of wear sleeve is as follows.
Tool O.D.
Minimum Thickness
inches (mm)6-3/4(171)
0.110(3)
8-1/2(216) 0.265
(7)11-1/4(286)
Drive Shaft
a. Check for spline wear. Blend any steps by grinding.
b. Visually check connection threads for wash or galling.
c. Visually check connection face for galling and deformation.
d. Visually check I.D. for excessive corrosion and wear.Reject if I.D. exceeds nominal diameter plus 1/8" (3 mm).
e. Visually check I.D. for pits. Reject if pit exceeds 1/32" (1 mm) deep.
f. Subject entire O.D. surface of part to magnetic particle inspection, particu-
larly in radius at change in diameter.
Tool SizeO.D.
6-3/4(171)
8-1/2(216)
11-1/4(286)
Top sub
6-5/8(168)
8-3/8(213)
11-1/8(282)
Equalizer Cylinder
Spring Cylinder
DPRS
Drive Cylinder
Drive Shaft
H Y D R A - S H O C K M o d e l B T o o l 26 E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 O p e r a t i o n & S e r v i c e M a n u a l
Wear Down Thickness
Table 4
O.D. Wear Down Tolerances - inches (mm)
Table 5
7/28/2019 Hydra Shock
34/68
Critical Parts Inspection
Measure all external parts for wear.
E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 27 H Y D R A - S H O C K M o d e l B T o o lO p e r a t i o n & S e r v i c e M a n u a l
Critical Parts Inspection
Comments ...........................................................................................................................
.............................................................................................................................................
.............................................................................................................................................
Date
Tool S/N:
Insp. Co:
7/28/2019 Hydra Shock
35/68
Critical Length Tolerance
Compare lengths to dimensions on the Fishing Dimensions Table. Iflength is out of tolerance per the amount shown below, the part must bereplaced.
H Y D R A - S H O C K M o d e l B T o o l 28 E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 O p e r a t i o n & S e r v i c e M a n u a l
SECTION 4
7/28/2019 Hydra Shock
36/68
Seal Assembly Procedures
Seal Description
The HE Group SUPER SEAL is a composite type of material with eachseal element performing a specific function.
The SNE Ring is forced down the gland taper to close the shaft to
gland clearance as pressure is applied to the Major Seal. Closure of
the SNE Ring prevents extrusion of the SSRRing and Major Seal.
The SSR, made of glass-filled Teflon, not only acts as a spacer be-
tween the Major Seal and SNE Ring, but polishes and conditions
the chrome and/or colmonoy shaft as it reciprocates under pres-
sure.
The Major Seal, the resilient seal member, must hold both low and
high pressure. The Major Seal is double-acting when a tapered seal
groove is provided as shown in the illustration below.
A Rod Wiper, positioned forward of the SUPER SEALS and PolyPak,prevents grease, mud and debris from entering.
Seal Inspection
Inspect all seals (O-rings, SNEs, SSRs, Major Seals, PolyPaks and RodWipers) after steam cleaning. If any seal appears worn or cracked, replaceit. Seal must be absolutely clean to reuse
E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 29 H Y D R A - S H O C K M o d e l B T o o lO p e r a t i o n & S e r v i c e M a n u a l
Seal Assembly Procedures
FIG. 20Super Seal
S N E R I N G
7/28/2019 Hydra Shock
37/68
Seal Assembly
Seals may be assembled into all designated parts before assembly of thetool or they may be assembled as designated parts are assembled. The ex-act order must be followed for each part.
Seal RetainerInternal seal grooves for all sizes
Step 1. Insert two PolyPaks into innermost internal seal grooves with O-ring to-
wards face of seal retainer.
Step 2. Insert rod wiper into outermost seal groove, with lip facing out.
Step 3. Repeat steps 1 and 2 for other end of retainer.
External seal grooves for 6-3/4" OD tool
Step 4. Assemble the T-seal into the external seal grooves and slide the seal to ei-ther side of the groove.
Step 5. Assemble one T-seal retainer into the seal groove opposite the T-seal.
Afterwards, slide the T-seal up to the retainer.
Step 6. Assemble another T-seal retainer by feeding one of the ends under the
T-Seal. Continue to feed the retainer until it is completely fitted into its
proper position. NOTE: Skived joints of both retainers should be 45E to
90Eoffset from each other.
External seal grooves for 8-1/2" OD tool & 11-1/4" OD tool
Step 7. Insert two PolyPaks at each end of the retainer. With PolyPak O-ring to-
wards face of seal retainer.
Equalizer Mandrel
Step 1. Insert PolyPaks, two PolyPaks at each end with O-ring towards face of
mandrel box connection.
Step 2. Insert rod wiper, with lip facing out, onto outermost seal groove.
Step 3. Repeat steps 1 and 2 for mandrel side of seal area.
H Y D R A - S H O C K M o d e l B T o o l 30 E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 O p e r a t i o n & S e r v i c e M a n u a l
SECTION 4
7/28/2019 Hydra Shock
38/68
Floating Piston
External seal grooves for 6-3/4" OD tool
Step 1. Assemble the T-seal into the external seal grooves and slide the seal to ei-
ther side of the groove.
Step 2. Assemble one T-seal retainer into the seal groove opposite the T-seal.
Afterwards, slide the T-seal against the T-seal retainer.
Step 3. Assemble another T-seal retainer by feeding one of the ends under the
T-Seal. Continue to feed the retainer until it is completely fitted into its
proper position.
NOTE: Skived joints of both retainers should be 45E to 90Eoffset from
each other.
Step 4. Assemble the bore wiper onto the external wiper groove, with lip facing
away from T-seals.
External seal grooves for 8-1/2" OD & 11-1/4" OD tool
Step 5. Insert two PolyPaks at each end of the floating piston, with PolyPak O-
ring towards face of seal retainer.
Step 6. Assemble the bore wiper onto the outer seal groove, with lip facing away
from PolyPaks.
Internal seal grooves all sizes
Step 7. Assemble twoSSR Rings into theseal groove. SSRrings maybecome de-formed and bent, but do not break or cut. Straighten out in groove after in-
sertion.
Step8. Push bothSSR Rings toeitherthe up orthe downsideof the groove. Rings
shouldfit snug andstay in selected positionwhen pushedto oneside of the
groove.
Step 9. Assemble an SNE Ring and hold together against the bevel of the groove
with the SSR Rings.
Step 10. Assemble the second SNE ring against the opposite side of the groove
and hold in place with the SSR ring. This will leave a space between theSSR rings. All rings should stay in place. If not, remove all rings and
slightly stretch all the SSR rings, but do not break. Reassemble as in Steps
7, 8 and 9.
Step 11. Assemble the major seal in between the separated SSR rings. Fold the
major seal in a U-shape and insert into the seal groove. Relax the major
seal into place.
E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 31 H Y D R A - S H O C K M o d e l B T o o lO p e r a t i o n & S e r v i c e M a n u a l
Seal Assembly Procedures
7/28/2019 Hydra Shock
39/68
Step 12. Assemble the rod wiper into the inner most seal groove. Fold the rod
wiper into a U-shape and snap the seal into place.
Spring Mandrel
Spring mandrel configuration
Step 1. Assemble PolyPak seals in grooves 2 and 3. (Note Direction)
Step 2. Assemble PolyPak seals in grooves 4 and 5. (Note Direction)
Step 3 Assemble bore wipers in grooves 1 and6 at each endof PolyPak grooves.
Drive Cylinder
Step 1. Apply a thin layer of heavy greaseto theouterdiameterof thewear sleeves
and install into I.D. grooves.
Step 2. Assemble two SSR rings into the seal groove. SSR rings may become
deformed and bent, but do not break or cut. Straighten out in groove after
insertion.
Step 3. Push both SSR rings to either the up or the down side of the groove. Ringsshould fit snugly and stay in selected position when pushed to one side of
the groove.
Step 4. Assemble an SNE ring and hold together against the bevel of the groove
with theSSR rings.SNE ring maybe held in position with a heavy grease.
Step 5. Assemble thesecond SNEring against theoppositeside of thegroove and
hold in place with the SSR ring. This will leave a space between the SSR
Rings. All rings should stay in place. If not, remove all rings and slightly
stretch all the SSR rings,but do not break. Reassemble as in Steps 2, 3 and
4.
Step 6. Assemble the major seal in between the separatedSSR rings.Fold thema-
jor seal in a U-shape and insert into the seal groove. Relax the seal into
place.
Step 7. Assemble the rodwiperinto the innermostseal groove. Fold therod wiper
into a U-shape and snap the seal into place.
H Y D R A - S H O C K M o d e l B T o o l 32 E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 O p e r a t i o n & S e r v i c e M a n u a l
SECTION 4
7/28/2019 Hydra Shock
40/68
SECTION 5
Assembly
Assembly begins with new or clean repaired parts. This section is applicable toright-hand threaded tools.
E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 33 H Y D R A - S H O C K M o d e l B T o o lO p e r a t i o n & S e r v i c e M a n u a l
Critical Factors& Safety Notes
Drive Cylinder
Clamp makeup device onto drive cylinder as shown in FIG. 21.
Insert wear sleeves as shown in Seal Assembly Procedures.
Insert seals as shown in Seal Assembly Procedures.
Shop Service - ASSEMBLYDescription & Sequence
FIG. 21
7/28/2019 Hydra Shock
41/68
H Y D R A - S H O C K M o d e l B T o o l 34 E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 O p e r a t i o n & S e r v i c e M a n u a l
SECTION 5
Critical Factors& Safety Notes
Shop Service - ASSEMBLYDescription & Sequence
FIG. 22
Drive Shaft
With drive cylinder in makeup device, clamp backup device ontodrive shaft as shown in FIG. 22.
Coat the shaft of the drive shaft with oil.
Slide drive shaft into the end of drive cylinder containing wearsleeves and seals until it seats on shoulder.
7/28/2019 Hydra Shock
42/68
E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 35 H Y D R A - S H O C K M o d e l B T o o lO p e r a t i o n & S e r v i c e M a n u a l
Assembly
Critical Factors& Safety Notes
Drive Pins
Align pin slots of drive shaft with pin slots of drive cylinder.
Install drive pins in the drive cylinder. Each slot should containtwo pins.
Shop Service - ASSEMBLYDescription & Sequence
FIG.23
7/28/2019 Hydra Shock
43/68
7/28/2019 Hydra Shock
44/68
E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 37 H Y D R A - S H O C K M o d e l B T o o lO p e r a t i o n & S e r v i c e M a n u a l
Assembly
Critical Factors& Safety Notes
Caution
Do not stand in frontof backup device ormakeup device whenapplying torque to thetool connection.
Connector Mandrel
Clamp backup device onto DPRS as shown in FIG. 25.
Clamp makeup device onto connector mandrel as shown in FIG.25
Thread the connector mandrel onto drive shaft with right-handrotation and make up to torque specified in Table 7.
Record torque on Smith Services-he Group Tool Service Report,page 52.
Slide the connector mandrel until it seats against the drive pin
retainer sub.
Shop Service - ASSEMBLYDescription & Sequence
FIG. 25
7/28/2019 Hydra Shock
45/68
H Y D R A - S H O C K M o d e l B T o o l 38 E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 O p e r a t i o n & S e r v i c e M a n u a l
SECTION 5
Critical Factors& Safety Notes
Load Washers & Belleville Springs
With DPRS in backup device, clamp makeup device onto unchromedshaft of spring mandrel as shown in FIG. 26.
Slide inner load washer onto spring mandrel.
Slide three springs in parallel onto the spring mandrel with the concaveside of the springs facing toward the DPRS as shown in FIG. 26A.
Slide the next set of three springs onto spring mandrel in theopposite direction of the first set as shown in FIG. 26A.
6-3/4" Continue this alternating pattern until forty-eight (48) sets of
springs (3 springs per set) have been placed on the spring man-
drel.
8-1/2" Continue this alternating pattern until forty-four (44) sets of
springs (3 springs per set) have been placed on the spring man-
drel.
11-1/4 Continue this alternating pattern until thirty (30) sets of springs
(3 springs per set) have been placed on the spring mandrel.
Slide outer load washer onto spring mandrel as shown in FIG. 26.
Shop Service - ASSEMBLYDescription & Sequence
FIG. 26
FIG. 26ASpring Pattern
7/28/2019 Hydra Shock
46/68
E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 39 H Y D R A - S H O C K M o d e l B T o o lO p e r a t i o n & S e r v i c e M a n u a l
Assembly
Critical Factors& Safety Notes
CAUTION
Do not stand in fromof backup device ormakeup device whenapplying torque to thetool connection.
Spring Mandrel
With DPRS in backup device and makeup device on unchromedshaft of spring mandrel, apply Kopr-Kote (or equivalent) tospring mandrel pin connections as shown in FIG. 27.
Thread spring mandrel into connector mandrel and make up totorque specified on Table 7.
Record torque on Smith Services-HE Group Tool Service Report,page 52.
Shop Service - ASSEMBLYDescription & Sequence
FIG. 27
7/28/2019 Hydra Shock
47/68
H Y D R A - S H O C K M o d e l B T o o l 40 E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 O p e r a t i o n & S e r v i c e M a n u a l
SECTION 5
Critical Factors& Safety Notes
Caution
Do not stand in frontof backup device ormakeup device whenapplying torque to thetool connection.
Do not damage Seals.
Do not bend springmandrel.
Do not scratchchrome.
Spring Cylinder
With backup device on DPRS, clamp makeup device onto springcylinder as shown in FIG.28 .
Slide the spring cylinder over the spring stack and onto the DPRS.
Thread spring cylinder onto DPRS and make up to the torquespecified in Table 7.
Record torque on Smith Services-HE Group Tool Service Report,page 52.
Shop Service - ASSEMBLYDescription & Sequence
FIG. 28
7/28/2019 Hydra Shock
48/68
E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 41 H Y D R A - S H O C K M o d e l B T o o lO p e r a t i o n & S e r v i c e M a n u a l
Assembly
Critical Factors& Safety Notes
Caution
Do not stand in frontof backup device ormakeup device whenapplying torque to thetool connection.
Do not damage Seals.
Do not bend springmandrel.
Do not scratchchrome.
Balance Cylinder
Clamp backup device onto spring cylinder as shown in FIG. 29.
Stroke tool completely open.
Clamp makeup device onto balance cylinder.
Apply Kopr-Kote (or equivalent) to the balance cylinder pinconnection.
Thread balance cylinder into spring cylinder and check shoulderstand off.
The balance cylinder shoulder should standoff from the springcylinder shoulder. This standoff is due to the spring stack preloadand is as follows for each size tool. See Table 6.
Tool Size O.D. Standoff
6-3/4(171)
9/32(7)
8-1/2(216)
3/8(10)
11-1/4
(286)
5/16
(8)
Make up to the torque specified in Table 7
Record torque on Smith Services-HE Group Tool Service Report,page 52.
Shop Service - ASSEMBLY
Description & Sequence
FIG. 29
Shoulder StandoffTable 6
7/28/2019 Hydra Shock
49/68
H Y D R A - S H O C K M o d e l B T o o l 42 E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 O p e r a t i o n & S e r v i c e M a n u a l
SECTION 5
Critical Factors& Safety Notes
Floating Piston
Assemble floating piston seals as shown in Seal AssemblyProcedures.
Coat OD piston seals with clean oil.
With backup device on spring cylinder and makeup device onbalance cylinder, slide the floating piston (OD seals first) onto thespring mandrel until the entire piston clears the box threads of thebalance cylinder as shown in FIG. 30.
Install spring mandrel seals as shown in Seal Assembly
Procedures.
Apply Kopr-Kote (or equivalent) to the spring mandrel pinconnection.
Shop Service - ASSEMBLYDescription & Sequence
FIG. 30
7/28/2019 Hydra Shock
50/68
E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 43 H Y D R A - S H O C K M o d e l B T o o lO p e r a t i o n & S e r v i c e M a n u a l
Assembly
Critical Factors& Safety Notes
Caution
Do not stand in frontof backup device ormakeup device whenapplying torque to thetool connection.
Do not scratch chromeplating in the equalizercylinder bore.
Do not damage Seals.
Do not bend springmandrel.
Equalizer Cylinder
Clamp backup device onto balance cylinder and shown in FIG. 31.
Clamp makeup device onto equalizer cylinder.
Apply Kopr-Kote (or equivalent) to the equalizer cylinder pinconnection.
Thread the equalizer cylinder onto the balance cylinder and makeup to the torque specified in Table 7.
Record torque on Smith Services-HE Group Tool Service Report,page 52.
Shop Service - ASSEMBLYDescription & Sequence
FIG. 31
7/28/2019 Hydra Shock
51/68
H Y D R A - S H O C K M o d e l B T o o l 44 E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 O p e r a t i o n & S e r v i c e M a n u a l
SECTION 5
Critical Factors& Safety Notes
Caution
Do not stand in frontof backup device ormakeup device whenapplying torque to thetool connection.
Do not damage Seals.
Equalizer Mandrel
Clamp backup device onto equalizer cylinder.
Clamp makeup device onto unchromed shaft of equalizer mandrel.
Insert equalizer mandrel seals as shown in Seal AssemblyProcedures.
Coat seals with clean oil.
Thread the equalizer mandrel onto the spring mandrel and make upto torque specified in Table 7.
Record torque on Smith Services-HE Group Tool Service Report,page 52.
Shop Service - ASSEMBLYDescription & Sequence
FIG. 32
7/28/2019 Hydra Shock
52/68
E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 45 H Y D R A - S H O C K M o d e l B T o o lO p e r a t i o n & S e r v i c e M a n u a l
Assembly
Critical Factors& Safety Notes
Seal Retainer & Wave Disc SpringAssemble seal retainer seals as shown in the Seal AssemblyProcedures.
Coat seals with clean oil.
With backup device on equalizer cylinder, slide seal retainer ontoequalizer mandrel, until the seal retainer clears the box threads ofthe equalizer.
Install the wave disc spring into the equalizer cylinder until it isagainst the seal retainer.
Shop Service - ASSEMBLYDescription & Sequence
FIG. 33
7/28/2019 Hydra Shock
53/68
H Y D R A - S H O C K M o d e l B T o o l 46 E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 O p e r a t i o n & S e r v i c e M a n u a l
SECTION 5
Critical Factors& Safety Notes
Caution
Do not stand in frontof backup device ormakeup device whenapplying torque to thetool connection.
Top Sub
With backup device on equalizer cylinder, clamp makeup deviceon top sub as shown in FIG. 34.
Apply Kopr-Kote (or equivalent) to the top sub threads.
Thread top sub into equalizer cylinder and make up to the torquespecified in Table 7.
Record torque on Smith Services-HE Group Tool Service Report,page 52.
Shop Service - ASSEMBLYDescription & Sequence
FIG. 34
7/28/2019 Hydra Shock
54/68
E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 47 H Y D R A - S H O C K M o d e l B T o o lO p e r a t i o n & S e r v i c e M a n u a l
Assembly
Critical Factors& Safety Notes
Caution
Do not stand in frontof backup device ormakeup device whenapplying torque to thetool connection.
Assembly Torque Check
Check torque applied to individual pieces withthe procedure below.
Do not use this procedure for overall make up oftool.
Clamp backup device onto the drive cylinder as shown in FIG. 35.
Clamp makeup device onto top sub.
Apply makeup torque as specified in Table 7.
Tap each external service connection with a one to two-poundhammer until all connections stop rotating and makeup torque isverified from end-to-end.
Record torque on Smith Services-HE Group Tool Service Report,page 52.
Shop Service - ASSEMBLYDescription & Sequence
FIG. 35
7/28/2019 Hydra Shock
55/68
7/28/2019 Hydra Shock
56/68
SECTION 6
Testing Procedures
The tool must be filled with oil, pressure tested and spring tested follow-ing assembly. Record test findings on Smith Services-HE Group ToolService Report.
Drive Section & Spring Section Pressure Test
1. Fill the drive section and spring section with Texaco Transformer oil
(or equivalent), see FIG. 36.
2. Apply pressure, up to 5,000 psi (34 000 kPa), and hold for five min-
utes. Perform this test on the drive section and the spring section. If
there is oil leakage at drive shaft or a drop in pressure, during either
test, disassemble the tool and replace the appropriate seals, and retest.
3. Record test findings on Smith Services-HE Group Tool Service Re-
port.
4. The tool MUST be oil-filled prior to shipment.
E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 49 H Y D R A - S H O C K M o d e l B T o o lO p e r a t i o n & S e r v i c e M a n u a l
FIG. 36Drive Section & Spring Section Pressure Test
7/28/2019 Hydra Shock
57/68
Internal Diameter Pressure Test
1. Install test sub on each end and torque up.
2. Fill the tools ID with oil or water, see FIG. 37.
3. Apply pressure up to 5,000 psi and hold for five minutes. If there is a drop
in pressure, if the tool starts to close, or if any leakage is noted disassemble
the tool and replace the appropriate seals. Then retest the tool.
4. Record test findings on Smith Services-HE Group Tool Service Report.
5. Drain the internal diameter of tool.
H Y D R A - S H O C K M o d e l B T o o l 50 E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 O p e r a t i o n & S e r v i c e M a n u a l
SECTION 6
FIG. 37Internal Diameter Pressure Test
7/28/2019 Hydra Shock
58/68
Spring Compression Test
Repeat test three times for stroke verification. Failure of this test shall ne-cessitate the disassembly of the tool, the replacement of the entire springstack, and a retest.
1. Place the HYDRA-SHOCK Model B tool in the test rack.2. With no load applied, measure and record the distance from the bot-
tom face of the drive cylinder to the top of the drive shaft as shown in
FIG. 38.
3. Apply compressive load per Table 9.
4. Measure the distance from the bottom face of the drive cylinder to the
top of the drive shaft at given load.
5. Record test findings on Smith Services-HE Group Tool Service Re-
port.
Tool sizeinches (mm)
Loadlbf (N)
Stroke
inches 1/2" (mm 12.7)
6-3/4(171)
50,000(222 400)
3(76)
8-1/2(216)
50,000(222 400)
2-1/2(64)
11-3/4(298)
50,000(222 400)
3(76)
E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 51 H Y D R A - S H O C K M o d e l B T o o lO p e r a t i o n & S e r v i c e M a n u a l
Testing Procedures
FIG. 38Spring Compression Test
Spring Compression Test
Table 9
7/28/2019 Hydra Shock
59/68
Smith Services-HE Group
Tool Service ReportC u s t o m e r S e r i a l N o .
D a y s O u t T o o l S i z e
D r i l l i n g O t h e r D i s t r i c t
I N C O M I N G R E P O R T
O P E R A T I O N T E S T
B Y
D a t e
S p r i n g C o m p r e s s i o n T e s t
S t r o k e
B e f o r e T e s t L o a d
i n c h e s ( m m )
T e s t L o a d
l b f ( N )
S t r o k e
W i t h T e s t L o a d
i n c h e s ( m m )
C o m m e n t s
D i s a s s e m b l y T o r q u e l b f f t ( N m )
B R E A K O U T
B Y
D a t e
T o p S u b ( T S ) S p r i n g C y l i n d e r ( S C )
E q u a l i z e r M a n d r e l ( E M ) S p r i n g M a n d r e l ( S M )
E q u a l i z e r C y l i n d e r ( E C ) C o n n e c t o r M a n d r e l ( C M )
B a l a n c e C y l i n d e r ( B C ) D r i v e P i n R e t a i n e r S u b ( D P R S )
O U T G O I N G R E P O R T
M A K E U P
B Y
D a t e
F I L L A N D T E S T P a s s e d
M A K E U P T O R Q U E l b f f t ( N m ) D r i v e S e c t i o n F i l l e d w i t h T r a n s f o r m e r O i l
I n t e r n a l C o n n e c t i o n s E x t e r n a l C o n n e c t i o n s
D r i v e S e c t i o n P r e s s u r e T e s t
C M l b f
f t
E a c h C o n n e c t i o n S p r i n g S e c t i o n F i l l e d w i t h T r a n s f o r m e r O i l
S M l b f f tl b f
f t
S p r i n g S e c t i o n P r e s s u r e T e s t
E M l b f f t A s s e m b l y T o r q u e C h e c k I n t e r n a l D i a m e t e r P r e s s u r e T e s t
l b f f t S e r v i c e C o n n e c t i o n G r e a s e d
T E S T
B Y
D a t e
S p r i n g C o m p r e s s i o n T e s t
S t r o k e
B e f o r e T e s t L o a d
i n c h e s ( m m )
T e s t L o a d
l b f ( N )
S t r o k e
W i t h T e s t L o a d
i n c h e s ( m m )
C o m m e n t s
C O M P L E T I O N R E P O R T
T . J . C o n n e c t i o n s G r e a s e d F u l l S e r v i c e
A p p r o v e d B y D a t e
T h r e a d P r o t e c t o r s
P a i n t I d e n t i f i c a t i o n
H Y D R A - S H O C K M o d e l B T o o l 52 E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 O p e r a t i o n & S e r v i c e M a n u a l
SECTION 6
7/28/2019 Hydra Shock
60/68
SECTION 7
Shipping Instructions
After testing and filling, the HYDRA-SHOCK Model B tool must becolor-coded and stenciled.
Thread protectors are required for shipment.
Record actions on Smith Services-HE Group Tool Service Report.
E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 53 H Y D R A - S H O C K M o d e l B T o o lO p e r a t i o n & S e r v i c e M a n u a l
Shipping Instructions
Use yellow paint to stencil tool.
Paint stencil will have 2" (51 mm)letters for 3-1/8" (80 mm) OD tooland smaller.
Paint stencil will have 4" (102 mm)letters for 3-3/4" (95 mm) OD tooland larger.
Red paint is used for Left HandConn. stencils.
Stencil Code
Tool Serial No.
_____________O.D. x ___________I.D.
HYDRA-SHOCK MODEL B TOOL
See Manual No. 1-50
SMITH SERVICESHE GROUP
PaintCode
7/28/2019 Hydra Shock
61/68
SECTION 8
Parts List
Tool ODinches (mm)
6 3/4(171)
8-1/2(216)
11-1/4(286)
Assembly Number 16999 16997 16988
Top SubQty
4139771
4139651
4139351
Equalizer CylinderQty
4139781
4139661
4139361
Balance CylinderQty
4140261
4140251
4140031
Spring CylinderQty
4139801
4139681
4139381
Drive Pin Retainer SubQty
4139811
4139691
4139391
Drive CylinderQty
4139821
4139701
4139401
Drive ShaftQty
4139861
4139711
4139441
Equalizer MandrelQty
4139831
4139741
4139411
Spring MandrelQty
4139841
4139731
4139421
Connector MandrelQty
4139851
4139721
4139431
Seal Retainer,Top Sub Qty
2183651
2183641
2183611
Floating PostonQty
3145611
3145591
3415441
Wave Disc SpringQty
1223321
1223311
1223271
Load WasherQty
1222982
1222942
1222752
Belleville Disc SpringQty
122297144
122293132
12227290
Drive PinQty
11303516
12046116
12227616
H Y D R A - S H O C K M o d e l B T o o l 54 E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 O p e r a t i o n & S e r v i c e M a n u a l
7/28/2019 Hydra Shock
62/68
Tool ODinches (mm)
6 3/4(171)
8-1/2(216)
11-1/4(286)
Wear Sleeve218337
3218329
3218295
3
Seal Kit Consisting ofRubber and Packing Kits
17019 17018 17000
Rubber Kit 17019R 17018R 17001
PolyPak, Ext.Seal Retainer Qty
Not Required122342
4122343
4
PolyPak, Int.Seal Retainer Qty
1223384
1223164
1223374
Wiper, Rod,Seal Retainer Qty
1223362
1223442
2182962
T-Seal,Seal Retainer Qty
2183442
Not Required Not Required
Wiper, Bore
Balance Man. Qty
218368
2
218377
2
218347
2PolyPak,Balance Man. Qty
1223374
1223464
1223424
Wiper, BoreSpring Man. Qty
1223394
1220854
1220854
PolyPak,Spring Mandrel Qty
2183692
2183732
2183732
Wiper, Bore, ThinSpring Mandrel Qty
2183601
2183741
2183751
Wiper, Rod, ThinFloating Piston Qty
2183671
1130581
2183081
Major SealFloating Piston Qty
2183412
2183362
2183092
PolyPak,Floating Piston, Qty
Not Required122342
4122343
4
T-Seal,Floating Piston Qty
2183442
Not Required Not Required
Wiper, BoreFloating Piston Qty
Not Required218374
1218375
1
Wiper, RodDrive Cylinder Qty
2183381
1130581
2183081
Major Seal,
Drive Cylinder Qty218341
2218336
2218309
2
Packing Kit 17019P 17018P 17002
Fill PlugDrive Cylinder Qty
1220721
1221531
122153
1
Fill PlugBalance Cylinder Qty
1220721
1221531
1221531
E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 55 H Y D R A - S H O C K M o d e l B T o o lO p e r a t i o n & S e r v i c e M a n u a l
Parts List
7/28/2019 Hydra Shock
63/68
Tool ODinches (mm)
6 3/4(171)
8-1/2(216)
11-1/4(286)
SNE RingDrive Cylinder Qty
2183394
1133564
2183114
SSRDrive Cylinder Qty
2183404
1133574
2183104
TSR,Drive Cylinder Qty
2183434
Not Required Not Required
SNE RingFloating Piston Qty
2183394
1133564
2183114
SSRFloating Piston Qty
2183404
1133574
2183104
TSRFloating Piston Qty
2183434
Not Required Not Required
H Y D R A - S H O C K M o d e l B T o o l 56 E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 O p e r a t i o n & S e r v i c e M a n u a l
SECTION 8
7/28/2019 Hydra Shock
64/68
SECTION 9
Fishing Diagrams
E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 57 H Y D R A - S H O C K M o d e l B T o o lO p e r a t i o n & S e r v i c e M a n u a l
Fishing Diagrams
Top Sub
Equalizer Mandrel
Balance Cylinder
Drive Pins
Spring Cylinder
Drive Cylinder
Spring Mandrel
Equalizer CylinderDrive Pin
Retainer Sub Drive Shaft
ConnectorMandrel
7/28/2019 Hydra Shock
65/68
Fishing Dimensions
Dimensions reflect new parts. Reworked or used parts may differ.
Tool ODinches (mm)
6 3/4 8 1/2 11 1/4
(171) (216) (286)
Top Sub
A6 3/4 8 1/2 11 1/4
(171.5) (215.9) (285.8)
B33 40 38
(838.2) (1016.0) (965.2)
C3 1/2 5 1/8 4 1/2
(88.9) (130.2) (114.3)
D29 35 1/2 32 1/4
(736.6) (901.7) (819.2)
E 4 4 1/2 5 3/4(101.6) (114.3) (146.1)
F4 3/4 6 1/4 8 3/8
(120.7) (158.8) (212.7)
Equalizer Mandrel
A3 1/4 3 3/4 4 3/8
(82.6) (95.6) (111.1)
B28 31 32 1/2
(711.2) (787.4) (825.5)
C2 13/16 3 3
(71.4) (76.2) (76.2)
D3 3/8 4.00 4 1/2
(85.7) (101.6) (114.3)
E11 10 10
(279.4) (254.0) (254.0)
F10 27/32 13 1/2 24 3/4
(275.4) (342.9) (628.7)
G4 6 6 3/4
(101.6) (152.4) (171.5)
H5 1/4 6 3/4 7
(133.4) (171.5) (177.8)
H Y D R A - S H O C K M o d e l B T o o l 58 E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 O p e r a t i o n & S e r v i c e M a n u a l
SECTION 9
7/28/2019 Hydra Shock
66/68
7/28/2019 Hydra Shock
67/68
Tool ODinches (mm)
6 3/4 8 1/2 11 1/4
(171) (216) (286)
Spring Mandrel
A3 7/8 5 1/4 5 1/4
(98.4) (133.4) (133.4)
B97 1/2 120 111
(2 476.5) (3 048.0) ( 2 819.4)
C2 13/16 3 3
(71.4) (76.2) (76.2)
D20 1/2 29 1/2 30
(520.7) (749.3) (762.0)
E23 27 1/2 29
(584.2) (698.5) (736.6)
F4 11/16 6 8 1/8
(119.1) (152.4) (206.4)
G 3 3/4 4 1/2 4 1/2(95.3) (114.3) (114.3)
Connector Mandrel
A4 1/2 6 5 3/4
(114.3) (152.4) (146.1)
B21 1/2 25 28
(546.1) (635.0) (711.2)
C3 3/4 4 3/8 4 3/8
(95.3) (111.1) (111.1)
D2 13/16 3 3
(71.4) (76.2) (76.2)
E4 11/16 6 7 13/16
(119.1) (152.4) (198.4)
F4 3/4 7 6 1/2
(120.7) (177.8) (165.1)
G3 1/2 5 5
(88.9) (127.0) (127.0)
H15 3/4 17 20 1/64
(400.1) (431.8) (508.4)
H Y D R A - S H O C K M o d e l B T o o l 60 E f f e c t i v e D a t e F e b r u a r y 2 0 0 1 O p e r a t i o n & S e r v i c e M a n u a l
SECTION 9
7/28/2019 Hydra Shock
68/68
Tool ODinches (mm)
6 3/4 8 1/2 11 1/4
(171) (216) (286)
Drive Pin Retainer Sub
A6 3/4 8 1/2 11 1/4
(171.5) (215.9) (285.8)
B16 17 20 13/16
(406.4) (431.8) (528.6)
C4 3/4 6 1/4 8 3/8
(120.7) (158.8) (212.7)
D5 5/8 7 1/4 9 7/8
(142.9) (184.2) (250.8)
E4 4 1/2 5 3/4
(101.6) (114.3) (146.1)
F12 8 9 5/16
(304.8) (203.2) (236.5)
Drive Pin
A3/4 1 1 1/4
(19.1) (25.4) (31.8)
B6 6 6
(152.4) (152.4) (152.4)
Drive Cylinder
A6 3/4 8 1/2 11 1/4
(171.5) (215.9) (285.8)
B43 3/4 47 51 1/2
(1 111.3) (1 193.8) (1 308.1)
C4 45/64 6 8 1/8
(119.5) (152.4) (206.4)
Drive Shaft
A4 11/16 6 8 1/8
(119.1) (152.4) (206.4)
B80 87 92
(2 032.0) (2 209.8) (2 336.8)
C2 13/16 3 3
(71.4) (76.2) (76.2)
E 48 52 61(1 219.2) (1 320.8) (1 549.4)
Fishing Dimensions