Hydraulic Hose
Braided - Multi-spiral - Powerwash - Thermoplastic - PTFE
Ranges from 3/16” to 2”
PART N
Hose SizeMin. Bend
Radius
Max. Working
Pressure
Min. Burst
PressureNominal
Braid Dia
Nominal
Hose OD
HYDRAULIC HOSE
DIN IMP. psi bar psi bar in. mm
PE105 04 3/16 9.5 11.5 3625 250 14500 1000 3.5 90
PE106 06 1/4 11.1 13.2 3263 225 13050 900 4.0 100
PE108 08 5/16 12.7 15.0 3118 215 12470 860 4.5 115
PE110 10 3/8 15.1 17.3 2610 180 10440 720 4.9 125
PE112 12 1/2 18.3 20.6 2320 160 9280 640 7.1 180
PE116 16 5/8 21.4 23.9 1885 130 7540 520 8.1 205
PE119 19 3/4 25.4 27.6 1523 105 6090 420 9.4 240
PE125 25 1 33.3 35.3 1305 90 5220 350 11.8 300
PART No. Braid Dia. Hose OD
1 WIRE BRAID HOSE - SAE 100R1S-AT - EN 853 1SN
1SN
PE131 31 1.1/4 40.5 43.2 914 63 3654 250 16.5 420
PE138 38 1.1/2 46.8 50.7 725 50 2900 200 19.7 500
PE151 51 2 60.2 64.2 580 40 2320 160 24.8 630
2 WIRE BRAID HOSE - SAE 100R2S-AT - EN 853 2SN
Special MSHA approved flame resistant outer cover can be provided on request.
Special Features: Qualified for double impulse cycles (300,000 cycles) to relevant standards‐SAE 100 R1S AT / EN 853 1SN / ISO 1436‐1SN. Good flexibility.Application: Medium to high pressure hydraulic lines. Suitable for petroleum based hydraulic fluids, synthetic esters, biodegradable hydraulic fluids, water‐glycol based fluids and air.
Liner: Synthetic oil resistant rubberReinforcement: One high tensile steel wire braidCover: Abrasion, ozone & weather resistant synthetic rubber.Working temperature : ‐40°C to 100°CIntermittent temperature: ‐ 40°C to +120°C (10% of total working hours).
For air application (max 70°C) & pressure above 17 bar cover must be pin pricked.
PE206 06 1/4 12.7 14.9 5800 400 23200 1600 3.9 100
PE208 08 5/16 14.3 16.7 5000 350 20000 1400 4.5 115
PE210 10 3/8 16.7 19.1 4785 330 19140 1320 4.9 125
PE212 12 1/2 19.8 22.1 3988 275 15950 1100 7.1 180
PE216 16 5/8 23.0 25.3 3625 250 14500 1000 8.1 205
PE219 19 3/4 27.0 29.6 3118 215 12470 850 9.4 240
PE225 25 1 35.1 37.7 2393 165 9570 650 11.8 300
PE231 31 1.1/4 44.7 47.7 1813 125 7250 500 16.5 420
PE238 38 1.1/2 50.8 54.0 1305 90 5220 360 19.7 500
PE251 51 2 63.3 67.5 1160 80 4640 320 24.8 630
2 WIRE BRAID HOSE - SAE 100R2S-AT - EN 853 2SN
Liner: Synthetic oil resistant rubber
2SN
PK106 06 1/4 10.5 12.5 3263 225 13050 900 2.0 50
PK108 08 5/16 11 5 13 5 3118 215 12470 860 2 2 55
1 WIRE BRAID COMPACT HOSE - EN857 1SC (smooth cover)
Special MSHA approved flame resistant outer cover can be provided on request.
Special Features: Qualified for double impulse cycles (400,000 cycles) to relevant standards‐SAE 100 R2S AT / EN 853 2SN / ISO 1436‐2SN. Good flexibility.
Liner: Synthetic oil resistant rubberReinforcement: Two high tensile steel wire braidsCover: Abrasion, ozone & weather resistant synthetic rubber.Working temperature : ‐40°C to 100°CIntermittent temperature: ‐ 40°C to +120°C (10% of total working hours).For air application (max 70°C) & pressure above 17 bar cover must be pin pricked.
Application: Medium to high pressure hydraulic lines. Suitable for petroleum based hydraulic fluids, synthetic esters, biodegradable hydraulic fluids, water‐glycol based fluids and air.
1SC PK108 08 5/16 11.5 13.5 3118 215 12470 860 2.2 55
PK110 10 3/8 13.7 15.7 2610 180 10440 720 2.4 60
PK112 12 1/2 17.0 19.0 2320 160 9280 640 2.8 70
PK116 16 5/8 20.4 22.4 1885 130 7540 520 3.5 90
PK119 19 3/4 23.8 25.8 1523 105 6090 420 3.9 100
PK125 25 1 31.4 33.5 1305 90 5220 360 6.3 160
Special Features: Qualified for double impulse cycles (300,000 cycles) to relevant standards‐EN 8571SC / ISO 11237‐1. Compact design results in good flexibility. Liner: Synthetic oil resistant rubber
Reinforcement: One high tensile steel wire braidCover: Abrasion, ozone & weather resistant smooth synthetic rubber.
Application: Medium to high pressure hydraulic lines. Suitable for petroleum based hydraulic fluids, synthetic esters, biodegradable hydraulic fluids, water‐glycol based
1SC
PK206 06 1/4 11.4 13.5 5800 400 23200 1600 2.0 50
PK208 08 5/16 13.0 15.0 5000 350 20000 1400 2.2 55
PK210 10 3/8 15.1 17.1 4785 330 19140 1320 2.6 65
PK212 12 1/2 18 3 20 5 3988 275 15950 1100 3 1 80
Special MSHA approved flame resistant outer cover can be provided on request.
2 WIRE BRAID COMPACT HOSE - EN857 2SC (smooth cover)
Working temperature : ‐40°C to 100°CIntermittent temperature: ‐ 40°C to +120°C (10% of total working hours).For air application (max 70°C) & pressure above 17 bar cover must be pin pricked.
hydraulic fluids, synthetic esters, biodegradable hydraulic fluids, water glycol based fluids and air.
2SCPK212 12 1/2 18.3 20.5 3988 275 15950 1100 3.1 80
PK216 16 5/8 21.5 23.5 3625 250 14500 1000 3.5 90
PK219 19 3/4 25.5 27.5 3118 215 12470 860 4.0 120
PK225 25 1 33.5 35.5 2393 165 9570 660 5.9 150
Special Features: Qualified for double impulse cycles (400,000 cycles) to relevant standards‐EN 8572SC / ISO 11237‐1. Compact design results in good flexibility. Liner: Synthetic oil resistant rubber
Reinforcement: Two high tensile steel wire braidsCover: Abrasion, ozone & weather resistant smooth synthetic rubber.Working temperature : ‐40°C to 100°CIntermittent temperature: ‐ 40°C to +120°C (10% of total working hours).For air application (max 70°C) & pressure above 17 bar cover must be pin
Application: Medium to high pressure hydraulic lines. Suitable for petroleum based hydraulic fluids, synthetic esters, biodegradable hydraulic fluids, water‐glycol based fluids and air.
Special MSHA approved flame resistant outer cover can be provided on request.
For air application (max 70 C) & pressure above 17 bar cover must be pin pricked.
4.1.1.b
PART N
Hose SizeMin. Bend
Radius
Max. Working
Pressure
Min. Burst
PressureNominal
Braid Dia
Nominal
Hose OD
HYDRAULIC HOSE
DIN IMP. psi bar psi bar in. mm
BX206 06 1/4 11.4 13.5 6525 450 26100 1800 2.0 50
BX208 08 5/16 13.0 15.0 6000 420 24400 1680 2.6 65
BX210 10 3/8 15.1 17.1 5500 380 22040 1520 3.1 80
BX212 12 1/2 18.7 20.9 4713 325 18850 1300 3.5 90
BX216 16 5/8 21.5 25.1 4205 290 16820 1160 4.7 120
BX219 19 3/4 27.5 30.0 4000 280 16000 1120 4.7 120
BX225 25 1 33.5 35.5 3000 210 12000 840 5.9 150
2 WIRE BRAID COMPACT HOSE - Exceeds EN857 2SC
PART No. Braid Dia. Hose OD
Special Features:Working pressure exceeds by 15 30% to EN 857 2SC standard Good
2SC+
TH206 06 1/4 12.7 14.9 5800 400 23200 1600 3.9 100
Special MSHA approved flame resistant outer cover can be provided on request.
2 WIRE BRAID HIGH TEMPERATURE HOSE - Exceeds EN 853 2SN 135°C (max)
Special Features: Working pressure exceeds by 15‐30% to EN 857 2SC standard. Goodflexibility with low bend radius for complex high pressure hydraulic circuits. Validated for 300,000 impulse cycles.
Liner: Synthetic oil resistant rubberReinforcement: Two high tensile steel wire braidsCover: Abrasion, ozone & weather resistant synthetic rubber.Working temperature : ‐40°C to 100°CIntermittent temperature: ‐40°C to +120°C (10% of total working hours).
Application: Very high pressure hydraulic lines. Suitable for petroleum based hydraulic fluids, such as mineral oils, fuels, hydrocarbons and glycol‐water based fluids.
2SNT TH208 08 5/16 14.3 16.7 5000 350 20000 1400 4.5 115
TH210 10 3/8 16.7 19.1 4785 330 19140 1320 4.9 125
TH212 12 1/2 19.8 22.1 3988 275 15950 1100 7.1 180
TH216 16 5/8 23.0 25.3 3625 250 14500 1000 8.1 205
TH219 19 3/4 27.0 29.6 3118 215 12470 850 9.4 240
TH225 25 1 35.1 37.7 2393 165 9570 650 11.8 300
TH231 31 1.1/4 44.7 47.7 1813 125 7250 500 16.5 420
TH238 38 1.1/2 50.8 54.0 1305 90 5220 360 19.7 500
TH251 51 2 63.3 67.5 1160 80 4640 320 24.8 630
Liner: Synthetic oil resistant rubberR i f t T hi h t il t l i b id
Special Features: Excellent weather and ozone resistant. Suitable to work at high ambient temperature (100°C)
2SNT
BA206PK 06 1/4 11.1 12.8 5800 4000 26825 1850 1.8 45
BA208PK 08 5/16 12.7 14.5 5075 350 24650 1700 2.2 55
BA210PK 10 3/8 14.8 16.6 4785 330 21750 1500 2.6 65
BA212PK 12 1/2 18.3 20.1 3988 275 17690 1220 3.1 80
Supplied in standard temperature black cover. (Blue MSHA cover available on request.)
ADVANCED COVER 2 WIRE BRAID COMPACT HOSE - Exceeds EN857 2SC
Reinforcement: Two high tensile steel wire braidsCover: Heat, ozone & weather resistant synthetic rubber.Working temperature : ‐40°C to 135°CIntermittent temperature: ‐ 40°C to +150°C
Application: Medium to High pressure hydraulic lines. Suitable for petroleum based hydraulic fluids, synthetic esters, biodegradable hydraulic fluids, water‐glycol based fluids at 135°C
ambient temperature (100 C).
2SCB
BA216PK 16 5/8 21.5 23.5 3625 250 15225 1050 3.5 90
BA219PK 19 3/4 25.4 27.6 3553 245 14210 980 4.7 120
Special Features: Superior impulse life and abrasion resistance.Highly flame
resistant antistatic cover. High ozone, weather and UV resistance. Wide range of fluid compatibility. Exceeds working pressure for standard 2SC forDN19 and DN25. MSHA approved flame resistant cover.
Liner: Synthetic oil resistant rubberReinforcement: Two high tensile steel wire braidsCover: Abrasion, flame, ozone & weather resistant synthetic rubber.Working temperature : ‐40°C to 100°CIntermittent temperature: ‐40°C to +125°C (10% of total working hours).
Application: Medium to high pressure hydraulic lines in heavy duty applications. of forestry,minning & earth moving equipment. Suitable for petroleum based hydraulic fluids, such as mineral oils,fuels, hydrocarbons and glycol‐water based fluids.
DIN IMP.
PE206R 06 1/4 80 28.82
PE210R 10 3/8 55 28.95
PE212R 12 1/2 45 28.80
PE219R 19 3/4 30 29.19 34-36 Mtr
2
2
1
1
2 WIRE BRAID HOSE ON REEL - EN 853 2SN
Coil LengthsCoil 1 Coil 2
Hose Size
Mts/Reel
Gross
Weight
(Kgs)
20-50 Mtr
20-50 Mtr
20-50 Mtr
50+ Mtr
50+ Mtr
20-50 Mtr
PART No.
Number of Hose
Coils
2SN
Special Features: Qualified for double impulse cycles (400,000 cycles) to relevant standards‐SAE 100 R2S AT / EN 853 2SN / ISO 1436‐2SN. Good flexibility.
Liner: Synthetic oil resistant rubberReinforcement: Two high tensile steel wire braidsCover: Abrasion, ozone & weather resistantsynthetic rubber.Working temperature : ‐40°C to 100°CIntermittent temperature: ‐ 40°C to +120°C (10% of total working hours).
Application: Medium to high pressure hydraulic lines. Suitable for petroleum based hydraulic fluids, synthetic esters, biodegradable hydraulic fluids, water‐glycol based fluids and air
Features & Benefits of Hose Reels: Packaged on compact cardboard reels to allow quick and easy access.Can be conveniently placed on shafts easing the hose cutting process. Can be despatched on a Next Day parcel carrier saving time and money. Minimises wastage as each reel contains a fixed quantity of hose.
total working hours).For air application (max 70°C) & pressure above 17 bar cover must be pin pricked.
fluids and air.
4.1.2.b
PART N
Hose SizeMin. Bend
Radius
Max. Working
Pressure
Min. Burst
PressureNominal
Braid Dia
Nominal
Hose OD
HYDRAULIC HOSE
DIN IMP. psi bar psi bar in. mm
PR410SP 10 3/8 17.5 21.4 6670 460 26680 1840 7.1 180
PR412SP 12 1/2 20.2 24.0 6235 430 24940 1720 9.0 230
PR416SP 16 5/8 23.8 27.6 5000 350 20000 1400 9.8 250
PR419SP 19 3/4 28.2 32.1 5000 350 20000 1400 11.8 300
PR425SP 25 1 35.6 38.7 4640 320 18560 1260 13.4 340
PR431SP 31 1.1/4 46.8 49.8 3000 210 12000 840 18.1 460
PR438SP 38 1.1/2 52.4 57.3 2755 190 11020 760 22.0 560
PR451SP 51 2 65.3 71.1 2610 180 10440 720 26.0 660
4 SPIRAL HOSE - EN 856 4SP - ISO 3862-1 4SP
PART No. Braid Dia. Hose OD
4SP
PR419SH 19 3/4 29.0 32.1 6000 420 24000 1680 11.8 280
4 SPIRAL HOSE - EN 856 4SH - ISO 3862-1 4SH
Liner: Synthetic oil resistant rubberReinforcement: Four high tensile steel wire spiralCover: High abrasion, ozone & weather resistantsynthetic rubber.Working temperature : ‐40°C to 100°CIntermittent temperature: ‐ 40°C to +120°C (10% of total working hours).
Special Features: Validated for 1,000,000 impulse cycles exceeding pressure rating of relevant standards. Good flexibility, weather and ozone resistant. MSHA approved flame resistant cover.
Application: High pressure, high impulse hydraulic applications eg. excavators, dozers, cranes, compactors, rock breakers, hydraulic drill rigs and other construction equipment. Suitable for petroleum based hydraulic fluids, synthetic esters, biodegradable hydraulic fluids, water‐glycol based fluids and air.
4SH PR425SH 25 1 35.6 38.7 5655 390 22620 1560 13.4 340
PR431SH 31 1.1/4 42.5 45.5 5000 350 20000 1400 18.1 460
PR438SH 38 1.1/2 49.0 52.5 4205 290 16820 1160 22.0 560
PR451SH 51 2 63.5 67.5 3625 250 14500 1000 26.0 700
Liner: Synthetic oil resistant rubberReinforcement: Four high tensile steel wire spiralCover: High abrasion, ozone & weather resistantsynthetic rubber.Working temperature : ‐40°C to 100°C
Special Features: Validated for 1,000,000 impulse cycles exceeding pressure rating of relevant standards. Good flexibility, weather and ozone resistant. MSHA approved flame resistant cover.
Application: High pressure, high impulse hydraulic applications eg. excavators, dozers, cranes, compactors, rock breakers, hydraulic drill rigs and other construction equipment. Suitable for petroleum based hydraulic
4SH
IM41035 10 3/8 17.5 20.6 5000 350 20000 1400 5.1 130
IM41235 12 1/2 21.0 24.0 5000 350 20000 1400 7.1 180
IM41635 16 5/8 24.6 27.6 5000 350 20000 1400 7.9 200
IM41935 19 3/4 29.0 32.1 5000 350 20000 1400 9.4 240
IM42535 25 1 35.6 38.7 5000 350 20000 1400 11.8 300
IM63135 31 1.1/4 46.8 49.8 5000 350 20000 1400 16.5 420
4 & 6 SPIRAL HOSE - EN 856 R13 - SAE 100 R13 - ISO 3862-1 R13
Intermittent temperature: ‐ 40°C to +120°C (10% of total working hours).
R13
IM63835 38 1.1/2 54.3 57.3 5000 350 20000 1400 19.7 500
IM65135 51 2 68.1 71.1 5000 350 20000 1400 23.6 600
4 & 6 SPIRAL HOSE SAE 100 R15 ISO 3862 1 R15
Liner: Synthetic oil resistant rubberReinforcement: Four high tensile steel wire spiralon 3/8" to 1" & 6 spiral on 1.1/4" to 2" Cover: High abrasion, ozone & weather resistantsynthetic rubber.Working temperature : ‐40°C to 121°CIntermittent temperature: ‐ 40°C to +125°C (10% of total working hours).
Special Features: Validated for 1,000,000 impulse cycles. Constant pressure rating across all hose sizes. Good flexibility, weather and ozone resistant. MSHA approved flame resistant cover.
Application: High pressure, high impulse hydraulicapplications eg. excavators, dozers, cranes, compactors, rock breakers, hydraulic drill rigs and other construction equipment. Suitable for petroleum based hydraulic fluids, synthetic esters, biodegradable hydraulic fluids, water‐glycol based fluids and air.
IM41042 10 3/8 17.5 21.4 6000 420 24000 1680 7.0 180
IM41242 12 1/2 21.6 24.6 6000 420 24000 1680 9.0 230
IM41642 16 5/8 25.6 28.6 6000 420 24000 1680 9.8 250
IM41942 19 3/4 28.2 32.0 6000 420 24000 1680 10.6 270
IM42542 25 1 35.5 39.0 6000 420 24000 1680 11.8 300
IM63142 31 1.1/4 46.8 50.0 6000 420 24000 1680 16.5 420
IM63842 38 1.1/2 55.0 58.0 6000 420 24000 1680 19.7 500
IM65142 51 2 69.0 72.0 6000 420 24000 1680 23.6 600
4 & 6 SPIRAL HOSE - SAE 100 R15 - ISO 3862-1 R15
Liner: Synthetic oil resistant rubberReinforcement: Four high tensile steel wire spiral Special Features: Validated for 1 000 000 impulse cycles Constant pressure rating across all hose
R15
Reinforcement: Four high tensile steel wire spiralon 3/8" to 1" & 6 spiral on 1.1/4" to 2" Cover: High abrasion, ozone & weather resistantsynthetic rubber.Working temperature : ‐40°C to 121°CIntermittent temperature: ‐ 40°C to +125°C (10% of total working hours).
Application: High pressure, high impulse hydraulicapplications eg. excavators, dozers, cranes, compactors, rock breakers, hydraulic drill rigs and other construction equipment. Suitable for petroleum based hydraulic fluids, synthetic esters, biodegradable hydraulic fluids, water‐glycol based fluids and air.
Special Features: Validated for 1,000,000 impulse cycles. Constant pressure rating across all hose sizes. Good flexibility, weather and ozone resistant. MSHA approved flame resistant cover.
4.1.3.b
H Si
Max. Working
P
Min. Burst
PN i l N i l
Min.
Bend
R di
Hose
C l
PRESSURE WASHER HOSE
DIN IMP. psi bar psi bar mm
AQ106BL 06 1/4 11.2 13.2 3625 250 13050 900 100 Black
AQ106BU 06 1/4 11.2 13.2 3625 250 13050 900 100 Blue
AQ108BL 08 5/16 13.0 15.0 3625 250 12325 850 115 Black
AQ108BU 08 5/16 13.0 15.0 3625 250 12325 850 115 Blue
AQ110BL 10 3/8 15.3 17.3 3625 250 11963 825 130 Black
AQ110BU 10 3/8 15.3 17.3 3625 250 11963 825 130 Blue
AQ112BL 12 1/2 18.5 20.6 3000 210 10150 700 180 Black
1 WIRE BRAID POWERWASH HOSE - 160°C (max)
PART No.
Hose Size Pressure PressureNominal
Braid Dia.
Nominal
Hose OD
Radius Colour
W250
AQ112BU 12 1/2 18.5 20.6 3000 210 10150 700 180 Blue
AQ206BL 06 1/4 12.7 14.9 5800 400 23200 1600 100 Black
Available in colours. BL=Black - BU=Blue
2 WIRE BRAID POWERWASH HOSE - 160°C (max)
Pin-pricked cover can be provided on request.
Liner: Synthetic water resistant rubberReinforcement: One high tensile steel wire braidCover: Non‐marking ,heat, abrasion, ozone & weather resistant synthetic rubber.Working temperature : ‐40°C to 160°C
Application: Suitable for Professional Pressure Washer applications up to 160°C.
Special Features: Light weight, high abrasion resistance & excellent resistance to ozone & common detergent solutions. No colour wash off. Conforms to high pressure wash jet machine hose safety requirements as per BS EN 1829. Not recommended for steam service.
W400 AQ206BU 06 1/4 12.7 14.9 5800 400 23200 1600 100 Blue
AQ208BL 08 5/16 14.6 16.7 5800 400 20300 1400 115 Black
AQ208BU 08 5/16 14.6 16.7 5800 400 20300 1400 115 Blue
AQ210BL 10 3/8 17.2 19.1 5800 400 18850 1300 130 Black
AQ210BU 10 3/8 17.2 19.1 5800 400 18850 1300 130 Blue
AQ212BL 12 1/2 20.0 22.1 5800 400 17400 1200 180 Black
AQ212BU 12 1/2 20.0 22.1 5800 400 17400 1200 180 Blue
Available in colours. BL=Black - BU=Blue Liner: Synthetic water resistant rubberReinforcement: Two high tensile steel wire braidsCover: Heat, abrasion, ozone & weather resistantsynthetic rubber.
W400
Special Features: Light weight, high abrasion resistance & excellent resistance to ozone & common detergent solutions. No colour wash off. Conforms to high pressure wash jet machine hose safety
AQ106BLK 06 1/4 10.5 12.5 3625 250 13050 900 50 Black
AQ106BUK 06 1/4 10.5 12.5 3625 250 13050 900 50 Blue
AQ108BLK 08 5/16 11.5 13.5 3625 250 12325 850 55 Black
AQ108BUK 08 5/16 11.5 13.5 3625 250 12325 850 55 Blue
AQ110BLK 10 3/8 13 7 15 7 3625 250 11963 825 60 Black
Pin-pricked cover can be provided on request.
1 WIRE BRAID COMPACT POWERWASH HOSE - 160°C (max)
Working temperature : ‐40°C to 160°CApplication: Suitable for Professional Pressure Washer applications up to 160°C.
g g p j y
requirements as per BS EN 1829. Not recommended for steam service.
W250C
AQ110BLK 10 3/8 13.7 15.7 3625 250 11963 825 60 Black
AQ110BUK 10 3/8 13.7 15.7 3625 250 11963 825 60 Blue
AQ112BLK 12 1/2 17.0 19.0 3000 210 10150 700 70 Black
AQ112BUK 12 1/2 17.0 19.0 3000 210 10150 700 70 Blue
Pin-pricked cover can be provided on request.
Available in colours. BLK=Black - BUK=Blue Liner: Synthetic water resistant rubberReinforcement: One high tensile steel wire braidCover: Non‐marking ,heat, abrasion, ozone & weather resistant synthetic rubber.Working temperature : ‐40°C to 160°C
Special Features: Light weight, high abrasion resistance & excellent resistance to ozone & common detergent solutions. No colour wash off. Conforms to high pressure wash jet machine hose safety requirements as per BS EN 1829. Not recommended for steam service.
Application: Suitable for Professional Pressure Washer applications up to 160°C.
AQ206BLK 06 1/4 11.5 13.5 5800 400 23200 1600 50 Black
AQ206BUK 06 1/4 11.5 13.5 5800 400 23200 1600 50 Blue
AQ208BLK 08 5/16 13.0 15.0 5800 400 20300 1400 55 Black
AQ208BUK 08 5/16 13.0 15.0 5800 400 20300 1400 55 Blue
AQ210BLK 10 3/8 15.1 17.1 5800 400 18850 1300 65 Black
AQ210BUK 10 3/8 15.1 17.1 5800 400 18850 1300 65 Blue
AQ212BLK 12 1/2 18.3 20.5 5800 400 17400 1200 80 Black
AQ212BUK 12 1/2 18.3 20.5 5800 400 17400 1200 80 Blue
Available in colours BLK=Black - BUK=Blue
2 WIRE BRAID COMPACT POWERWASH HOSE - 160°C (max)
Liner: Synthetic water resistant rubber
W400C
Available in colours. BLK Black BUK Blue
Pin-pricked cover can be provided on request.
Liner: Synthetic water resistant rubberReinforcement: Two high tensile steel wire braidsCover: Heat, abrasion, ozone & weather resistantsynthetic rubber.Working temperature : ‐40°C to 160°C
Application: Suitable for Professional Pressure Washer applications up to 160°C.
Special Features: Light weight, high abrasion resistance & excellent resistance to ozone & common detergent solutions. No colour wash off. Conforms to high pressure wash jet machine hose safety requirements as per BS EN 1829. Not recommended for steam service.
4.1.4.b
PART N
Hose SizeMin. Bend
Radius
Max. Working
Pressure
Min. Burst
PressureIntrenal
Hose Dia
Nominal
Hose OD
THERMOPLASTIC HOSE
DIN IMP. psi bar psi bar in. mm
R7205TH 05 3/16" 4.8 10.0 3045 210 12180 840 1.18 30
R7206TH 06 1/4" 6.4 11.8 2900 200 11600 800 1.38 35
R7208TH 08 5/16" 8.0 14.3 2755 190 11020 760 1.77 45
R7210TH 10 3/8" 9.7 16.0 2537 175 10150 700 2.17 55
R7212TH 12 1/2" 13.0 20.3 2030 140 8120 560 2.95 75
R7219TH 19 3/4" 19.2 26.5 1305 90 5220 360 5.71 145
R7225TH 25 1" 25.6 32.5 1015 70 4060 280 7.87 200
2 POLYESTER BRAID THERMOPLASTIC HOSE - SAE 100 R7 - EN 855 R7
PART No. Hose Dia. Hose OD
Liner: Thermoplastic technopolymer.
Reinforcement: Two synthetic fibre braids
R7
R7205THTW 05 3/16" 4.8 10.0 3045 210 12180 840 1.18 30
R7206THTW 06 1/4" 6.4 11.8 2900 200 11600 800 1.38 35
R7208THTW 08 5/16" 8.0 14.3 2755 190 11020 760 1.77 45
R7210THTW 10 3/8" 9.7 16.0 2537 175 10150 700 2.17 55
R7212THTW 12 1/2" 13.0 20.3 2030 140 8120 560 2.95 75
R7219THTW 19 3/4" 19.2 26.5 1305 90 5220 360 5.71 145
2 POLYESTER BRAID THERMOPLASTIC TWIN HOSE - SAE 100 R7 - EN 855 R7
Applications: Medium pressure general hydraulic applicationsHydraulic instrumentation and movable tooling.
Reinforcement: Two synthetic fibre braids.Cover: Abrasion resistant black polyurethane.Working temperature : ‐40°C to 100°C (‐40°C to 70°C water & air)
R7
R7225THTW 25 1" 25.6 32.5 1015 70 4060 280 7.87 200
R8205TH 05 3/16" 4.8 10.0 5075 350 20300 1400 1.38 35
R8206TH 06 1/4" 6.4 11.8 5075 350 20300 1400 1.97 50
R8208TH 08 5/16" 8.0 14.3 4712 325 18850 1300 2.36 60
R8210TH 10 3/8" 9.7 16.0 4060 280 16240 1120 2.76 70
R8212TH 12 1/2" 13 0 20 3 3552 245 14210 980 3 74 95
2 ARAMID BRAID THERMOPLASTIC HOSE - SAE 100 R8 - EN 855 R8
R8
R8212TH 12 1/2" 13.0 20.3 3552 245 14210 980 3.74 95
R8219TH 19 3/4" 19.2 26.5 2392 165 9570 660 5.91 150
R8225TH 25 1" 25.6 34.7 2100 145 8410 580 7.87 200
R8205THTW 05 3/16" 4.8 10.0 5075 350 20300 1400 1.38 35
R8206THTW 06 1/4" 6.4 11.8 5075 350 20300 1400 1.97 50
R8208THTW 08 5/16" 8.0 14.3 4712 325 18850 1300 2.36 60
2 ARAMID BRAID THERMOPLASTIC TWIN HOSE - SAE 100 R8 - EN 855 R8
Liner: Thermoplastic technopolymer.
Reinforcement: Two aramidic Kevlar fibre braids.
Cover: Abrasion resistant black polyurethane.Working temperature : ‐40°C to 100°C (‐40°C to 70°C water & air)
Applications: Medium to high pressure general hydraulic applications. High pressure pneumatic systems.
R8R8210THTW 10 3/8" 9.7 16.0 4060 280 16240 1120 2.76 70
R8212THTW 12 1/2" 13.0 20.3 3552 245 14210 980 3.74 95
R8219THTW 19 3/4" 19.2 26.5 2392 165 9570 660 5.91 150
R8225THTW 25 1" 25.6 34.7 2100 145 8410 580 7.87 200
R7205THNC 05 3/16" 4.8 10.0 3045 210 12180 840 1.18 30
2 POLYESTER BRAID THERMOPLASTIC HOSE - SAE 100 R7 Non-conductive
R7 R7206THNC 06 1/4" 6.4 11.8 2900 200 11600 800 1.38 35
R7208THNC 08 5/16" 8.0 14.3 2755 190 11020 760 1.77 45
R7210THNC 10 3/8" 9.7 16.0 2537 175 10150 700 2.17 55
R7212THNC 12 1/2" 13.0 20.3 2030 140 8120 560 2.95 75
R7219THNC 19 3/4" 19.2 26.5 1305 90 5220 360 5.71 145
R7225THNC 25 1" 25.6 32.5 1015 70 4060 280 7.87 200
2 POLYESTER BRAID THERMOPLASTIC HOSE - SAE 100 R8 Non-conductive
Applications: Medium to high pressure applications requiring a high electrical isolation.
Liner: Thermoplastic technopolymer.
Reinforcement: Two synthetic fibre braids.Cover: Abrasion resistant orange polyurethane.Working temperature : ‐40°C to 100°C (‐40°C to 70°C water & air)
R7
R8205THNC 05 3/16" 4.8 10.0 3045 210 12180 840 1.18 30
R8206THNC 06 1/4" 6.4 11.8 2900 200 11600 800 1.38 35
R8208THNC 08 5/16" 8.0 14.3 2755 190 11020 760 1.77 45
R8210THNC 10 3/8" 9.7 16.0 2537 175 10150 700 2.17 55
R8212THNC 12 1/2" 13.0 20.3 2030 140 8120 560 2.95 75
R8219THNC 19 3/4" 19.2 26.5 1305 90 5220 360 5.71 145
R8225THNC 25 1" 25.6 32.5 1015 70 4060 280 7.87 200Liner: Thermoplastic technopolymer.
Reinforcement: Two aramidic Kevlar fibre braids.Cover: Abrasion resistant orange polyurethane.Working temperature : ‐40°C to 100°C (‐40°C to 70°C water & air)
Applications: Medium to high pressure applications requiring a high electrical isolation.
R8
4.1.7.b
P T F E HOSE
Part No.
Nominal
I.D. Bore
Size Ins.
Nominal
I.D. Bore
Size mm
Working
Pressure
Bar
Burst
Pressure
Bar
Mild Steel
Ferrule
Part No.
Stainless
Ferrule
Part No.
SMOOTH BORE PTFE HOSE WITH 304 STAINLESS STEEL ONE WIRE BRAIDHPTFE SB 06 1/4" 6.70 175 700 PTTB.06 VPTTB.06
HPTFE SB 10 3/8" 10.00 135 540 PTTB.10 VPTTB.10
HPTFE SB 13 1/2" 13.40 120 480 PTTB.13 VPTTB.13
HPTFE SB 16 5/8" 16.60 100 400 PTTB.16 VPTTB.16
HPTFE SB 19 3/4" 19.80 90 360 PTTB.19 VPTTB.19
HPTFE SB 25 1" 26 10 65 260 PTTB 25 VPTTB 25HPTFE SB 25 1 26.10 65 260 PTTB.25 VPTTB.25
Liner: Smooth PTFECover: One high tensile 304 stainless steel wire braid.Working temperature : ‐60°C to 260°C
Applications: Low Pressure Hydraulics, Food, Distilling, Air Conditioning, Marine, Chemical, Industrial Gases, Process Plant etc.
Special Features: Inert to virtually all chemicals. Resistance to weathering/ageing, unaffected by UV light, resistant to oxidation, non‐flammable, low permeability, solevent resistant and a wide
CONVOLUTED PTFE HOSE WITH 304 STAINLESS STEEL ONE WIRE BRAIDHPTFE C 06 1/4" 6.73 160 510 PTC.06 VPTC.06
HPTFE C 10 3/8" 9.14 120 480 PTC.10 VPTC.10
HPTFE C 13 1/2" 12.45 110 440 PTC.13 VPTC.13
HPTFE C 16 5/8" 15.37 80 320 PTC.16 VPTC.16
HPTFE C 19 3/4" 18.54 70 280 PTC.19 VPTC.19
HPTFE C 25 1" 24.89 50 200 PTC.25 VPTC.25
HPTFE C 32 1.1/4" 31 45 180 PTCE.32 VPTC.32
HPTFE C 38 1.1/2" 37.5 40 160 PTCE.38 VPTC.38
HPTFE C 50 2" 48 36 144 PTCE.50 VPTC.50
Liner: Helically Convoluted PTFECover: One high tensile 304 stainless steel wire braid.Working temperature : ‐60°C to 260°C
Applications: Low Pressure Hydraulics Food Distilling Air Conditioning Marine Chemical Industrial Gases Process Plant etc
Special Features: Inert to virtually all chemicals. Resistance to weathering/ageing, unaffected by UV light, resistant to oxidation, non‐flammable, low permeability, solevent resistant and a wide
Notes
NOTE 1: DistagQCS standard range of fittings can be used on PTFE hose in
Applications: Low Pressure Hydraulics, Food, Distilling, Air Conditioning, Marine, Chemical, Industrial Gases, Process Plant etc.
NOTE 1: DistagQCS standard range of fittings can be used on PTFE hose inconjunction with the above ferrules.
NOTE 2: DistagQCS offer an assembly and testing service to customer specifications.
4.1.8.b
Ferrule Part No Hose Type Specification Size Range Identification
FERRULE SELECTION CHART
POWERWASH W250
POWERWASH W250C
EN 856 4SP - ISO 3862-1 4SP 3/8" to 2"
2SC+ 5/8" to 1"
POWERWASH W400PF12
1/4" to 1/2"
1/4" to 1/2" Roll Stamped PF11PF11
Roll Stamped PF12
POWERWASH W400C
EN 857 1SC
EN 857 2SC
2SC+ 1/4" to 1/2"
EN 853 1SN - SAE R1AT 1/4" to 1"
1/4 to 1/2
1/4" to 1"
PF15 Roll Stamped PF15
EN 853 1SN - SAE R1AT 1.1/4" to 2"
EN 853 2SN - SAE R2AT 1/4" to 2"
Thermoplastic EN 855 R7
Thermoplastic EN 855 R83/16" to 1/2"PF23
PF22 Roll Stamped PF22
Roll Stamped PF23
PTFE Convoluted Extruded
Stainless Steel 1 Wire Braid
PTFE Convoluted Tape Wrapped
Stainless Steel 1 Wire Braid
PTC1/4" to 2"
1/4" to 1"
Roll Stamped PTC
PTFE Convoluted Extruded
Stainless Steel 1 Wire Braid
PTFE Smooth Bore
Stainless Steel 1 Wire Braid
EN 856 4SH ISO 3862 1 4SH 3/4" t 2"
1.1/4" to 2"
1/4" to 1"
PTCE
PTTB
Roll Stamped PTCE
Roll Stamped PTTB
EN 856 4SH - ISO 3862-1 4SH 3/4" to 2"
EN 856 R13 - SAE 100 R13
SAE 100 R15 - ISO 3862-1 R15
EN 856 R13 - SAE 100 R13
SAE 100 R15 - ISO 3862-1 R151.1/4" to 2" Roll Stamped MPF4MPF4
MPF33/4" to 1"
Roll Stamped MPF3
EN 853 1SN - SAE R1AT
EN 853 2SN - SAE R2AT
R710
R720
1/4" to 3/4"
Two Rings at Thread End
One Ring at Thread End
1/4" to 3/4"
4.1.9.b