CalipersSkiving Tools and Vise BlocksFerrule Vises
Field Support EquipmentWarning Statement
265
GENERAL
INFORMATION
SPECIALTY
HOSE
COUPLINGS
MISC
EQUIPMENT
BRAIDED
HOSE
SPIRAL
HOSE
Dayco Eastman products are part of an engineered system which must be assembled and used inaccordance with Dayco Eastman instructions and limitations.
Dayco Eastman hose, couplings and crimping machines are designed as an effective and reliableassembly system and the use of other than Dayco Eastman products may produce hose assemblies thatwill not meet rated performance. Failure to follow Dayco Eastman instructions and limitations could leadto premature hose failures resulting in property damage, serious injury or death.
Dayco Eastman’s limited warranty shall apply only if the customer uses hose, fittings, hose fitting com-ponents and crimp equipment specifically engineered, designed and produced to Dayco Eastmanprocess specifications.
DAYCO EASTMAN DISCLAIMS ANY RESPONSIBILITY OR LIABILITY FOR ANY CRIMPED HOSEASSEMBLIES NOT PRODUCED FROM GENUINE DAYCO EASTMAN HOSE FITTINGS, HOSE ANDEQUIPMENT, IN CONFORMANCE WITH DAYCO EASTMAN PROCESS SPECIFICATIONS FOR EACHSPECIFIC HOSE ASSEMBLY.
DO NOT USE A DAYCO EASTMAN CRIMPING MACHINE WITHOUT DIES!
m WARNING
How the Kwikrimp® System works
The Kwikrimp® system is like having a miniature hose assembly “factory” at your disposal. In just minutes, theKwikrimp® hose coupling system produces the exact hose and coupling combination needed, in an assemblythat meets original equipment manufacturer specifications.
Utilizing the proven principle of much larger factory equipment, eight segmented crimping dies apply tons offorce on the coupling, making an attachment that is stronger than the hose itself. The segmented dies areforced against the coupling shell by a tapered die actuator, powered by heavy duty hydraulic rams. Self cen-tering feature assures equal force distribution through all the dies, producing a uniform crimp pressure on thefull shell circumference.
Unique, easily adjusted settings provide the operator with accurate control of the crimping operation.Approximate settings are preset for the type of hose and coupling used, providing approximate crimp diame-ters. (verification of proper crimp diameter with calipers or other measuring device is required).
NOTE: Hose and coupling compatabilites noted in this catalog are for reference purposes only. DaycoEastman Crimping Specifications is the official guide for selecting appropriate hose and coupling combinationsand determining crimper compatibility.
Lightweight and easy to carry, the S-16 Porta-Swage™ can swage SU series only couplings onNR7, NR7E, S7 &, S7E, S8 and S8E style hoses.Dies and pushers listed below are sold separately.
SQ-101-SW Swager
267
GENERAL
INFORMATION
SPECIALTY
HOSE
COUPLINGS
MISC
EQUIPMENT
BRAIDED
HOSE
SPIRAL
HOSE
*Burst pressure is for reference and design purposes onlyand is no indication that the product should be used abovethe indicated related working pressure.
For field assembly of Dayco Eastman S6 (-12 & -16) Predator® sewer cleaning hose. It's a tool designed for municipalitiesand sewer cleaning contractors which will give the user the ability to repair and extend the life of a reel of hose, should dam-age occur. Only SQ couplings may be swaged by using the SQ-101-SW.The SQ-101-SW swager, couplings and hose tube are color coded red, making it easy to identify that the components aremade by Dayco Eastman. By following Predator® hose inspection instruction card, P-1211(included with each reel of hose),and swage assembly instructions, the user can have assurance of making an acceptable hose assembly.
DIES AND PUSHERS:SQ-101-12S6/S9 -12 size die for S6 and S9 hoseSQ-101-12P -12 size pusherSQ-101-16S6 -16 size die for S6 hose (only)SQ-101-16S9 -16 size die for S6 hose (only)SQ-101-16P -16 size pusherSQ-101-20S6 -20 size die for S6 hose (only)SQ-101-20P -20 size die pusher
A B C DCat. Hose Cut HexNo. I.D. Thread O.A.L. Off Orifice Size
† SQ couplings are swageable using the SQ-101-SW swager.
Kwikrimp® Crimpers
268
GENERAL
INFORMATION
SPECIALTY
HOSE
COUPLINGS
MISC
EQUIPMENT
BRAIDED
HOSE
SPIRAL
HOSE
EC30 Portable CrimperDescription: The EC30 Portable Crimper has the capacity to crimp from 1/4” through 1” I.D. 2-wire braid hydraulic hose and
4-spiral through 3/4” with all coupling end styles.The EC30 Portable Crimper is marketed in component parts, tailored to fit the exact need of the user. Drilled feet allow easy and secure mounting on bench or vehicle.EC30 Portable Crimper includes pusher plate, adapters, hose assembly and instruction manual.Pumps and dies are purchased separately.
Capability: 1/4” through 1” I.D. 2-wire braid hydraulic hose and 4-spiral hose through 3/4” I.D. with all coupling end styles,including most bent tubes.
Power Source(s): Two Stage Hand Pump (EC30-22)Air Hydraulic Pump (EC30-23)Electric Hydraulic Pump (P-116-10), 1/2 HP, 120 Volt, 60 hz, Single Phase Motor (Foot Pedal Included)Electric Hydraulic Pump (EN97-021), 1/2 HP, 230 Volt, 50 hz, Single Phase MotorElectric Hydraulic Pump (EN97-022), 1/2 HP, 230 Volt, 50 hz, Single Phase CE Listed Motor
Die Sets Die SizeEN98-020-09 .350 OrangeEN98-020-01 .520 RedEN98-020-02 .670 YellowEN98-020-03 .830 BlueEN98-020-04 1.100 GreenEN98-020-05 1.320 BlackEN98-020-06 1.500 BrownEN98-020-07 1.730 Silver
Kwikrimp® Crimpers
269
GENERAL
INFORMATION
SPECIALTY
HOSE
COUPLINGS
MISC
EQUIPMENT
BRAIDED
HOSE
SPIRAL
HOSE
K-16-LPDescription: Basic Kwikrimp® open bowl, split ram design which uses an easy to read mechanical gauge to control crimp
diameter. Two piece die design provides easy installation. Lightweight enough for portable field use.
K-16-LP Crimper includes standard die sets, hose assembly and instruction manual.Pump and optional dies must be purchased separately.
Capability: Crimps 1/8” I.D. through 1” I.D. two wire braid hose, including bent tubes.
Power Source(s): Two Stage Hand Pump (EC30-22)Electric Hydraulic Pump (P-116-10), 1/2 HP, 120 Volt, 60 hz, Single Phase Motor (Foot Pedal Included).Air Hydraulic Pump (EC30-23)
Dimensions: 11” Wide x 8” Deep x 11 5/8” High
Weight: 112 lbs. (Without Pump)
Dies: K-16 Standard Options:Die Sets Die Size K-16 Optional Die Sets Die SizeK-16DS0500 .500 die set K-16DS0325 .325 die setK-16DS0750 .750 die set K-16DS0400 .400 die setK-16DS1050 1.050 die set K-16DS1750 1.750 die set
Kwikrimp® Crimpers
270
GENERAL
INFORMATION
SPECIALTY
HOSE
COUPLINGS
MISC
EQUIPMENT
BRAIDED
HOSE
SPIRAL
HOSE
K-501-LPDescription: Open bowl, split ram design Kwikrimp® machine that is ideal as a portable or on-site machine for shop applications
that require a versatile crimper.K-501-LP Crimper includes standard die sets, hose assembly and instruction manual.Pump and optional dies must be purchased separately.
Capability: Crimps 1/8” I.D. through 1 1/4” I.D. SAE 100R9 hose, including most bent tube couplings.
Power Source(s): Two Stage Hand Pump (EC30-22)Electric Hydraulic Pump (P-126-10),1/2 HP, 120 Volt, 60 hz, Single Phase Motor (Foot Pedal Included).Air Hydraulic Pump (EC30-23)
Dimensions: 11” wide x 8” deep x 17” high
Weight: 180 lbs. (without pump)
Dies: K-501 Options:Standard Die Sets Die Size K-501 Optional Die Sets Die Size
K-401DS0500 .500 die set K-501DS0325 .325 die setK-401DS0750 .750 die set K-501DS0400 .400 die setK-401DS1050 1.050 die setK-401DS1550 1.550 die setK-401DS1750 1.750 die set
Kwikrimp® Crimpers
271
GENERAL
INFORMATION
SPECIALTY
HOSE
COUPLINGS
MISC
EQUIPMENT
BRAIDED
HOSE
SPIRAL
HOSE
K-24-EPDescription: Open bowl, split ram design Kwikrimp® machine. Features that will add speed and accuracy include color coded dies,
two piece die design for easy installation, automatic crimp stops, coupling stop, cycle reducing foot switch. Pump, standard die sets, die storage bins and instruction manual are standard. Optional dies must be purchased separately.
Capability: Crimps 1/8” I.D. through 1 1/2” I.D. SAE 100R13 hose, including most bent tube couplings.
Power Source: Two Stage Electric Pump, (P-124-10 Pump), Included With The Crimper115 Volt, 60 hz, Single Phase Motor (Foot Pedal Included)
Dimensions: 16” Wide x 13” Deep x 20” High
Weight: 528 lbs.
Dies: K-24 Standard Options:Die Sets Die Size K-24 Optional Die Sets Die Size
K-24DS0500 .500 die set K-24DS0400 .400 die setK-24DS0750 .750 die set K-24DS0875S .875S die setK-24DS1050 1.050 die set K-24DS1000S 1.000S die setK-24DS1275S 1.275S die setK-24DS1550 1.550 die setK-24DS1750 1.750 die setK-24DS1975 1.975 die set
Kwikrimp® Crimpers
272
GENERAL
INFORMATION
SPECIALTY
HOSE
COUPLINGS
MISC
EQUIPMENT
BRAIDED
HOSE
SPIRAL
HOSE
K-601-LPDescription: Open bowl, split ram design Kwikrimp® machine that will handle high pressure hose applications with versatility
and dependability.K-601-LP Crimper includes standard die sets, hose assembly, die storage bins and instruction manual.Pump and optional dies must be purchased separately.
Capability: Crimps 1/8” I.D. through 2” I.D. SAE 100R12 4-Spiral Hose, Including Most Bent Tube Couplings.
Power Source: Two Stage Electric Pump (P-125-10), 115 Volt, 60hz, Single Phase Motor (Foot Pedal Included).
Dimensions: 18 1/2” Wide x 12 1/2” Deep x 22 1/2” High
Weight: 527 lbs. (Without Pump)
Dies: K-601 Options: Die SetsStandard Die Sets Die Size K-601 Optional Die Size
K-601DS0500 .500 die set K-601DS0325 .325 die setK-601DS0750 .750 die set K-601DS0400 .400 die setK-601DS1050 1.050 die set K-601DS0875S .875S die setK-601DS1275 1.275 die set K-601DS1000S 1.000S die setK-601DS1550 1.550 die setK-601DS1750 1.750 die setK-601DS1975 1.975 die setK-601DS2500 2.500 die set
Kwikrimp® Crimpers
273
GENERAL
INFORMATION
SPECIALTY
HOSE
COUPLINGS
MISC
EQUIPMENT
BRAIDED
HOSE
SPIRAL
HOSE
NP60Description: Accurate, reliable and easy to operate, Dayco Eastman’s NP60 Crimper costs no more than many less productive
conventional crimpers. NP60 has a digital controller. Compare the NP60’s value-adding features and benefits with your present crimper.
NP60: Complete Crimper With 6 Sets Of Dies (2 Piece Die Sets) and 115V 60 hz Single Phase 1 HP MotorNP60A: Complete Crimper With 6 Sets Of Dies (1 Piece Die Sets) and 115V 60 hz Single Phase 1 HP MotorNP60N: Complete Crimper With No Dies and 115V 60 Cycle Single Phase 1 HP MotorNP60G: Complete Crimper With 6 Sets Of Dies (2 Piece Die Sets) and 220V 50 hz Single Phase 1 HP Motor
Capability: Delivers 60 tons of force through six standard die sets to let you crimp 1 and 2 wire hose through 1 1/2” I.D. and4-spiral hose through 3/4” I.D. (or up to 1 1/4” I.D. 4-spiral hose with optional dies)
Dimensions: 32” wide x 32” deep x 34” high
Weight: 270 lbs.
Dies: Standard Die Sets Die SizeEN98-020-01 .520 RedEN98-020-02 .670 YellowEN98-020-03 .830 BlueEN98-020-04 1.100 GreenEN98-020-05 1.320 BlackEN98-020-07 1.730 Silver
EN96-027 Bent Tube Pusher Plate
Options: Optional dies are available to increase crimping capacity through 1 1/4” I.D. on 4-spiral hoses, up to and including SAE 100R12 hose.
OptionalOptional Die Sets Die Size Knock-Down Bell Dies Die Size (mm)
EN98-020-09 Orange .350 EN98-042-01 Red 14 mm KDBEN98-020-06 Brown 1.500 EN98-042-02 Yellow 18 mm KDBEN98-020-08 Purple 1.920 EN98-042-03 Blue 20 mm KDBEN98-035-01 White (Bubble) .580 EN98-042-04 Green 28 mm KDBEN98-035-02 White (Bubble) .850 EN98-042-05 Purple 34 mm KDB
State of the Art NP60Electronic Digital Controls
✔ Located at eye level for maximum convenience✔ Assured faster set-up and operation – one of the industry’s fastest✔ Simplified, user-friendly controls take the guesswork out of crimping.✔ No special skill needed to assure accurate settings.✔ More accurate control of crimp diameter produces more reliable
coupling retention.✔ Eliminates the need for additional tooling purchases as new hoses
and fittings become available.✔ Completely sealed surface membrane on control panel reduces
contamination of internal components.
COLOR CODING SAVES TIME, HELPS PREVENT MISTAKES . . .✔ Entire retainer ring is color-coded to speed die selection and set-up.✔ Convenient built-in die storage shelves eliminates lost dies.✔ Color-coded die selection guide is printed right on the machine for
easy, mistake-proof die selection.
Kwikrimp® Crimpers
274
GENERAL
INFORMATION
SPECIALTY
HOSE
COUPLINGS
MISC
EQUIPMENT
BRAIDED
HOSE
SPIRAL
HOSE
WB60Description: Dayco Eastman’s WB60 Crimper is one of the most economical crimpers in the market today. This machine provides
the accuracy and reliability, plus the ease of set-up and operation that you demand from a crimper. Adjustable dieclosures reduce the number of set-ups and die changes. Color-coded dies make die changes faster and prevent crimping with the wrong set of dies. Two piece drop-in dies also save time during set-ups.Each unit includes 10 sets of dies as standard equipment, which are stored in built-in storage shelves.Optional dies must be purchased separately.
WB60: Complete Crimper with 10 Sets of Dies and 2 HP, 120V, 60 hz, 20 Amp Motor (20 Amp Circuit Required)WB60G: Complete Crimper with 10 Sets of Dies and 2 HP, 230V, 50 hz, Single Phase.
Additional features include:✔ Simple calibration and start-up procedure ✔ Improved potentiometer adjustment✔ Digital Controller ✔ Coupling Stop✔ Flex-arm work light for improved visibility ✔ Manual & instruction video✔ Additional electrical outlet to plug in lamp ✔ Shelf to store manual & crimp specs
Capability: Offers Improved Cycle Time and Delivers 60 Tons of ForceAbility to Crimp 1 and 2 Wire Braid, as Well as 4-Spiral Hose Assemblies Through 2” I.D. and 6-Spiral AssembliesThrough 1 1/2” I.D.
Power Source(s): 2 HP, 120 V, 60 hz, 20 Amp (20 Amp Power Required)60 Ton Cylinder With 6 Inch Stroke (Pump Included)
Dimensions: 43” Wide x 35” Deep x 38” High
Weight: 514 lbs.
Dies: Standard Optional Die SetsDie Sets Die Size Knock-Down Bell Die SizeEN98-020-01 Red .520 EN98-042-01 Red 14 mm KDBEN98-020-02 Yellow .670 EN98-042-02 Yellow 18 mm KDBEN98-020-03 Blue .830 EN98-042-03 Blue 20 mm KDBEN98-020-04 Green 1.100 EN98-042-04 Green 28 mm KDBEN98-020-05 Black 1.320 EN98-042-05 Purple 34 mm KDBEN98-020-07 Silver 1.730EN98-020-08 Brown 1.500EN98-020-09 Purple 1.920EN98-032-01 Pink 2.300EN98-032-02 White 2.800
EN96-027 Bent Tube Pusher Plate
State of the Art NP60Electronic Digital Controls
✔ Located at eye level for maximum convenience✔ Assured faster set-up and operation – one of the industry’s fastest✔ Simplified, user-friendly controls take the guesswork out of crimping.✔ No special skill needed to assure accurate settings.✔ More accurate control of crimp diameter produces more reliable
coupling retention.✔ Eliminates the need for additional tooling purchases as new hoses
and fittings become available.✔ Completely sealed surface membrane on control panel reduces
contamination of internal components.
COLOR CODING SAVES TIME, HELPS PREVENT MISTAKES . . .✔ Entire retainer ring is color-coded to speed die selection and set-up.✔ Convenient built-in die storage shelves eliminates lost dies.
Kwikrimp® Crimpers
275
GENERAL
INFORMATION
SPECIALTY
HOSE
COUPLINGS
MISC
EQUIPMENT
BRAIDED
HOSE
SPIRAL
HOSE
KK125ADescription: New generation KK series Kwikrimp® machine that utilizes microprocessor control for the fastest, most accurate
crimping system available. Easy to use and maintain.Includes manual die change tool, Kwikchange™ die tool, foot pedal, die holder panel, stand and operator’s manual. A total of seven standard die sets are included.
Capability: Crimps 1/8” through 1 1/4” SAE 100R12 hose.
Power Source(s): 230/460 V, 3 Phase11/5.5 Amp (Please specify voltage when ordering crimper).
Dimensions: 26” Wide x 20” Deep x 24” High
Weight: 450 lbs.
Dies: KK125 Standard Die Sets Die SizeKK125DS12-84 1284KK125DS19-84 1984KK125DS24-84 2484KK125DS30-84 3084KK125DS32-84 3284KK125DS39-84 3984KK125DS47-84 4784
Options:Special die sets, automatic back stop switch. Pin Support System (KK125PSS); consult Dayco Eastman for price and availability.
Kwikrimp® Crimpers
276
GENERAL
INFORMATION
SPECIALTY
HOSE
COUPLINGS
MISC
EQUIPMENT
BRAIDED
HOSE
SPIRAL
HOSE
KK250Description: New generation KK series Kwikrimp® machine that utilizes microprocessor control for the fastest, most accurate
crimping system available. Easy to use and maintain.Includes manual die change tool, Kwikchange™ die tool, foot pedal, stand and operator’s manual. A total of 12 standard die sets are included.
Capability: Crimps 1/8” through 2” 6-spiral hose (special dies may be required)
Dimensions: 27” wide x 22” deep x 28” high
Weight: 500 lbs.
PowerSource(s): 230/460 V, 3 Phase
11/5.5 Amp
Dies: KK Standard Die Sets Die SizeKK200DS12-99 1299KK200DS19-99 1999KK200DS24-99 2499KK200DS30-99 3099KK200DS32-99 3299KK200DS39-99 3999KK200DS47-99 4799KK200DS50-99 5099KK200DS53-99 5399KK200DS55-99 5599KK200DS59-99 5999KK200DS66-99 6699
Options: Special Die Sets, Automatic Back Stop Switch. Consult Dayco Eastman for price and availability.
Kwikrimp® Crimpers
277
GENERAL
INFORMATION
SPECIALTY
HOSE
COUPLINGS
MISC
EQUIPMENT
BRAIDED
HOSE
SPIRAL
HOSE
NP100ADescription: Precise controls take the guesswork out of crimping. Unique two-piece drop-in die system reduces changeover time.
Color-coded die rings make die selection easy and helps prevent mistakes. Die storage rack included. Dies and pumpsold separately.
Capability: Provides fast, accurate set-up and repetitive crimping on textile braid, wire braid and spiral hose constructions. Delivers 100 tons of pressure for 6-spiral hose assemblies ranging from 3/16” through 2”.
Options: Die Sets Die SizeEN85-050-02 Red .520EN85-050-03 Yellow .670EN85-050-04 Blue .830EN85-050-05 Green 1.100EN85-050-06 Black 1.320EN85-050-07 Brown 1.500EN85-050-08 Silver 1.730EN85-050-09 Purple 1.920EN85-050-10 Rose 2.140EN85-050-11 Gold 2.500EN85-050-12 White 2.800
NP100-20 Foot PedalAn option that permits hands-free operationof the NP100A model crimper.
Support EquipmentPumps
278
GENERAL
INFORMATION
SPECIALTY
HOSE
COUPLINGS
MISC
EQUIPMENT
BRAIDED
HOSE
SPIRAL
HOSE
EC30-22Two Stage Hand Pump
Lightweight and completely portable pump for use with EC30, K-16or K-501 crimpers.
System: 10,000 PSI factory set relief valve
Size: 23” long x 6” wide x 9” high
Weight: 11 lbs.
P-116-10Electro-Hydraulic Pump
Electric driven hydraulic pump for use with EC30 or K-16 crimpers,includes foot pedal.System: 10,000 PSI factory set relief valve
1/2 HP, 115V, 60 cycle, single phase
Size: 9” long x 13” wide x 18” high
Weight: 49 lbs.
EC30-23Air Pump
Air driven hydraulic pump for use with EC30, K-16 or K-501 crimpers,80 to 120 psi required.System: 10,000 PSI factory set relief valve
Size: 22” long x 6 1/2” wide x 5 3/4” high
Weight: 18 lbs.
Support EquipmentPumps
279
GENERAL
INFORMATION
SPECIALTY
HOSE
COUPLINGS
MISC
EQUIPMENT
BRAIDED
HOSE
SPIRAL
HOSE
P-125-10Two Stage Electric Pump
Electric driven hydraulic pump for use with K-601 crimper, includes footpedal.
System: 7,500 PSI factory set relief valveTwo-way hydraulic control valve1 HP, 115V, 60 hz, single phase
Weight: 91 lbs.
P-126-10Two Stage Electric Pump
Electric driven hydraulic pump for use with K-501 crimper, includes footpedal
System: 10,000 PSI factory set relief valveTwo-way hydraulic control valve1 HP, 115V, 60 hz, single phase
Weight: 91 lbs.
Support EquipmentHose Assembly Cleaning System
280
GENERAL
INFORMATION
SPECIALTY
HOSE
COUPLINGS
MISC
EQUIPMENT
BRAIDED
HOSE
SPIRAL
HOSE
Dayco Eastman is now making the latest hose cleaning technology avail-able to its customers. The CE System (Contamination Elimination) makescleaning hose assemblies faster and easier than ever before. Compressedair propels a foam projectile that is 20% larger than the I.D. through thehose. Expanding as it enters the hose from the CE unit, the projectile forcescontaminant's out of the hose.
The CE System consists of three basic components:1. Specially designed launcher2. A range of CE nozzles to fit hose, BSP fittings and JIC fittings3. Projectiles for hose (standard) and coupling applications.
Dayco Eastman offers 2 sizes of CE System kits:1. CE-100, which cleans hoses to 1 1/4” I.D.2. CE-200, which cleans hoses up to 2” I.D.
Each kit is complete with CE Unit, handbook, operating & safety video, noz-zles and projectiles. Observe all Safety Precautions Provided With Kit.
Small Kit CE-100PartNumber Description Qty.CE1-U Pneumatic Projectile Launcher (CE Unit) 1CE1-M Owner’s Handbook (CE System) 1CEAR1 Adaptor Ring (CE Unit) 1CE1-SC Projectile Sizing Chart 1CE1-V Operational & Safety Procedures Video 1CEQRC-C Quick Release Coupling - Complete 1CE1-CC-LP Plastic Carry Case (Foam Insert) - Large 1
CE-S07 Standard Projectile 7mm 100CE-S10 Standard Projectile 10mm 100CE-S12 Standard Projectile 12mm 100CE-S14 Standard Projectile 14mm 100CE-S16 Standard Projectile 16mm 100CE-S18 Standard Projectile 18mm 100CE-S20 Standard Projectile 20mm 100CE-S22 Standard Projectile 22mm 100CE-S26 Standard Projectile 26mm 50CE-S33 Standard Projectile 33mm 40CE-S40 Standard Projectile 40mm 30
New bench mounted multiple gang hose cutter designed to cut thermo-plastic and textile braid hoses up through 1” I.D.
Weight: 7 lbs.
Replacement blade: SE136
SE140Hose Cut-Off Saw
The ideal light medium duty hose cut-off saw. It will cleanly cut single ordouble wire braid reinforced hose up to 1 1/4” I.D. as well as thermo-plastic hoses. The 1 HP motor is usable in 115/230 V, single phase, 60 hz. Uses 7” blade with 5/8" arbor.
Overall Dimensions: 13” x 24” x 17”
Weight: 113 lbs.
SE155 and SE160Heavy Duty Saw/Skiver
This saw will cleanly cut single or double wire braid and spiral rein-forced hoses up to 2” I.D. as well as thermoplastic hoses. In addition,all hoses up through 2” I.D. may be skived with this unit. The 3 HPmotor is available in single or three phase. Uses 10” blade with 3/4"arbor. See next page for SE190 Replacement Skiving Brush information.
This saw will cleanly cut single or double wire braid and spiral reinforcedhoses up to 2” I.D. as well as thermoplastic hoses. The 3 HP motor isavailable in single or three phase. Uses 10” blade with 3/4" arbor.
Rugged hose cut-off saw that will handle the smallest to the 2” heavy 6-spiral wire hose easily and reliably. Ideally suited for production cuttingwhere efficiency of operation and speed are essential. Double chain, holddown L-vise with hand lock.
Specifications: SE200: 3 HP, 3 phase, 220/440 volt, 60 Hz motor(Imperial Eastman 208-T equivalent)SE210: 2 HP, single phase, 220 volt, 60 Hz motor(Imperial Eastman 211-T equivalent)
SE201: Blade (abrasive) - 11” diameter
Abrasive Blade: SE201 11" with 1" arbor.
SE165 and SE170Saw Blade
Scalloped construction for better heat dissipation and a cleaner cut.These blades can be resharpened many times and can be reversed fortwice the life.
Specifications: SE165: 7” diameter x 5/8” arbor for SE140SE170: 10” dia. x 3/4” arbor for SE145,SE150, SE155,and SE160
SE190Skiving Brush
Replacement skiving brush for SE155 and SE160 for accurate skiving.
SE175 and SE180Saw Blade
Standard beveled edge blade made from high speed steel. Can beresharpened many times.
Specifications: SE175: 7” dia. x 5/8” arbor for SE140SE180: 10” dia. x 3/4” arbor for SE145, SE150, SE155, and SE160
Support Equipment
283
GENERAL
INFORMATION
SPECIALTY
HOSE
COUPLINGS
MISC
EQUIPMENT
BRAIDED
HOSE
SPIRAL
HOSE
KK CaliperCaliper for Measuring
Finished Crimp Dimensions
Specifically designed to measure finished coupling crimp diameters onDayco Eastman hose assemblies. Notched caliper jaws allow measure-ment of crimped coupling “flats”. Easy to use and provides accuratereadings within 0.001 of an inch. Instructions included.
Part Number: KKCALIPER
SE195Spiral Wire Skiving Tool
Easy to use, accurate skiving tool designed especially for spiral wirehose. Can be used on hose through 2” I.D.
Replacement Blade: SE195-1
SSK2Internal Skiving Tool
Internal skiving tool for NH32 hose.
Replacement Blade: EN93-050
BRAIDED
HOSE
SPIRAL
HOSE
Support Equipment
284
GENERAL
INFORMATION
SPECIALTY
HOSE
COUPLINGS
MISC
EQUIPMENT
BQ Assembly ToolAssembly Tool for BQ Series37˚ Swivel Female Couplings
All BQ couplings with FJ swivel female 37˚ ends require the use of thisassembly tool.
SE40 and SE41Vise Blocks
The SE40 vise blocks are designed to hold 3/16” to 1/2” I.D. hosesecurely in place while assembling reusable couplings.The SE41 vise blocks are designed to hold 3/4” to 1” I.D. hose securelyin place while assembling reusable couplings.
HPT5Coupling Pusher
Makes 1/4" and 3/8" I.D. hose assemblies with push-on couplings.
HEX COUPLINGCATALOG SIZE OF CATALOGNUMBER TOOL NUMBER
Kwik-Skive hand tools remove a hose cover in under a minute. Automaticstop for skive length. Smooth, almost effortless operation. Ideal for largerhose diameters where bulky hose lengths make machine skiving difficult.
221-T: Replacement Blade
Note: 200-T skive tools are pre-set for the proper skive length. Scuff washers are not necessary.
Note: ST style skive tools listed by hose/coupling combination by size in the following manner. . . .
660-T and 670-T Ferrule ViseFor Use With KFA and KFB Ferrules
660-T Ferrule Vise: Vise for making hose assemblies with barbed inserts and ferrules. Furnished with removable handle. Dies can also be used in the Schrader vise. Dies must be ordered separately. When ordering dies specify size of ferrule with which they are to be used.Weight: 26.4 lbs.
670-T Air Operated Ferrule Vise: Vise is ideal for volume hose assembly operations. Used for making hose assemblies with barbed inserts and ferrules with less effort than hand operated models.A normal shop air source is all that is required to activate this unit. Extra rugged, heavy-duty construction on the air cylinder, foot switch and vise body insures dependable, trouble-free service.Weight: 61 lbs.
