IContents
I
© 2011 HYPET Data AS
Table of ContentsPart I Introduction 1
Part II INPUT BEFORE TEST 2
Part III PRINT-Setup 8
Part IV PRINT-Report 9
Part V DRAFT 22
Part VI MAIN 24
Part VII WEIGHTS 26
Part VIII PENDULUM 27
Part IX TEST DATA 27
Part X DW-CODES 30
Part XI TEST 31
Part XII LIGHT SHIP 32
Part XIII 2.5D VIEW 33
Index 0
HYPET 700 - Heelin test program1
© 2011 HYPET Data AS
1 Introduction
About program HYPET 700, H700w.To create a complete heeling test report form input data from an inclination test.
Main screen looks like this:
This report is based on the template from the Norwegian Maritime Directorate in Norway.First and mainly, the report is intended to communicate directly with a HYPET hull database that is builtup in H100w, but can also be run separately. If a HYPET hull database exists, the program willautomatically get current main data from this database and also calculate the hydrostatic data for thecurrent waterline. You can start with data entry by selecting from the menu at the top from left:"DRAFT", "MAIN", "WEIGHT", "Pendulum", "TEST DATA" and "LIGHT SHIP".
Below you will find screenshots from the program and the full report.
Introduction 2
© 2011 HYPET Data AS
2 INPUT BEFORE TEST
Document used to collect necessary data during the heeling test:file: Heeling test report Input-E.doc
HYPET 700 - Heelin test program3
© 2011 HYPET Data AS
INPUT BEFORE TEST 4
© 2011 HYPET Data AS
HYPET 700 - Heelin test program5
© 2011 HYPET Data AS
INPUT BEFORE TEST 6
© 2011 HYPET Data AS
HYPET 700 - Heelin test program7
© 2011 HYPET Data AS
INPUT BEFORE TEST 8
© 2011 HYPET Data AS
3 PRINT-Setup
About "PRINT" and tab "Color": Press color-rectangle to select own colors.
About "PRINT" and tab "Report":
HYPET 700 - Heelin test program9
© 2011 HYPET Data AS
Press OK button and PRINT-Report will be created.
4 PRINT-Report
REPORT LOOKS LIKE THIS USING EXAMPLE SHIP: MS FISH
PRINT-Report 10
© 2011 HYPET Data AS
HYPET 700 - Heelin test program11
© 2011 HYPET Data AS
PRINT-Report 12
© 2011 HYPET Data AS
HYPET 700 - Heelin test program13
© 2011 HYPET Data AS
PRINT-Report 14
© 2011 HYPET Data AS
HYPET 700 - Heelin test program15
© 2011 HYPET Data AS
PRINT-Report 16
© 2011 HYPET Data AS
HYPET 700 - Heelin test program17
© 2011 HYPET Data AS
PRINT-Report 18
© 2011 HYPET Data AS
HYPET 700 - Heelin test program19
© 2011 HYPET Data AS
PRINT-Report 20
© 2011 HYPET Data AS
HYPET 700 - Heelin test program21
© 2011 HYPET Data AS
PRINT-Report 22
© 2011 HYPET Data AS
5 DRAFT
When input DRAFT-READING, please have this in mind:1. Use the same longitudinal location or frame reference for both SB and PS.
2. Following input for DRAFT is very helpful: M , H M = Height from BASE LINE up to measuring point and Normal to BASE LINE. H = Height from WATER LINE up to measuring point and Normal to WATER LINE. Example: 6.856+0.007+1.040 , 3.880 which mean: About M: 6.856m (BL to deck) +0.007m (deck thick.) +1.040m (from deck to measuring point) Using method "M,H" program will automatically handled any trim!
BUT you are allowed to input DRAFT directly, but then you must take care of trim yourself. Have in mind that all draft calculation in HYPET is measured normal to BASE LINE. Please read help text inside different tabs.
About "Draft" and tab"Draft":
HYPET 700 - Heelin test program23
© 2011 HYPET Data AS
About "Draft" and tab"Explanation - formulas":
About "Draft" and tab"About draft input":
DRAFT 24
© 2011 HYPET Data AS
6 MAIN
About "MAIN" and tab "General data":
About "MAIN" and tab "Ship data":
HYPET 700 - Heelin test program25
© 2011 HYPET Data AS
About "MAIN" and tab "Ship as inclined":
About "MAIN" and tab "Comments on the inclining test":
MAIN 26
© 2011 HYPET Data AS
7 WEIGHTS
About "WEIGHT" and tab "Inclining weights":
About "WEIGHT" and tab "Drawing(s) inside waterline plan":
HYPET 700 - Heelin test program27
© 2011 HYPET Data AS
8 PENDULUM
About "PENDULUM" and tab "Pendulum definition":
9 TEST DATA
About "TEST DATA" and tab "Test points":
Here you see data for Pendulum 1.
Double-click wanted "Test point" in table above and you see screen like this:
TEST DATA 28
© 2011 HYPET Data AS
Input/maintain WEIGHT-movement and PENDULUM-movement.More weights can be moved in the same move.
About "TEST DATA" and tab "Pendulum info":
HYPET 700 - Heelin test program29
© 2011 HYPET Data AS
DW-CODES 30
© 2011 HYPET Data AS
10 DW-CODES
About "DW-CODES":
HYPET 700 - Heelin test program31
© 2011 HYPET Data AS
11 TEST
About "TEST" and tab "Result calculation":
Here you can easy see result for all pendulum calculation.
About "TEST" and tab "Testing of the result":
LIGHT SHIP 32
© 2011 HYPET Data AS
12 LIGHT SHIP
About "LIGHT SHIP" and tab "Weights to be removed":
Pos.1 will include "Total inclining weights" automatically.I addition include all "Weights to be removed" inside this table.
About "LIGHT SHIP" and tab "Weights to be added":
Add all "Weights to be added" inside this table.
HYPET 700 - Heelin test program33
© 2011 HYPET Data AS
THEN: Pless button (Calculate LightShip) and LIGHT SHIP will be calculated.At bottom line you will find DRAFT calculation for light ship depending on selected "Water spec. gravity(t/m3)"
13 2.5D VIEW
About "2.5D VIEW":
Here you see waterline for: SHIP AS INCLINED."Corrected DA" and "Corrected DF" inside DRAFT-input are used.