Date post: | 02-Jul-2015 |
Category: |
Devices & Hardware |
Upload: | tushar-kumar |
View: | 122 times |
Download: | 0 times |
CN D&T Group
IAD Configuration (SS)
V1.1
2
Objects
1. Configuration of SPC Property
2. Configuration of SPC Capacity
3. IAD Gateway Cluster Configuration
4. Configuration of Data Area Capacity
5. Zone to Card Configuration
6. Reboot the SPC Card
7. IAD Node Configuration
8. IAD User Configuration
9. TID Default Attribute Configuration
10. Configuration of the TID Name
These slides will show you the details about IAD configuration on SS. Including the following steps:
3
Configuration of SPC Property
We must select Call & H.248 in processing scope to configure IAD on particular SPC Card
Right Click SS Configure Management Globe Configuration SS Data Configuration Shelf Configuration Right Click SPC Card Property Configuration
4
Configuration of SPC Property
Chennai IAD has Configured in 3rd Shelf 14th SPC Card (LSQ=94)
LSQ= [(Shelf No.-1)*40+Slot No.]
5
Configuration of SPC Capacity
Right Click SS Configure Management Globe Configuration SS Data Configuration Shelf Configuration Right Click SPC Card Property Configuration
The Capacity should be filled in according to the actual situation
For IAD, the following should be configured.
Capacity of the TID text
Subscriber Capacity
Maximum Nodes
6
Configuration of SPC Capacity
7
IAD Gateway Cluster Configuration
Gateway Cluster is the set of gateway nodes with the same properties. The nodes with different equipment types cannot exist in the same gateway cluster. In the SS system, SPC data area and hundred groups are allocated in the unit of gateway cluster. Before addition of IAD equipment, the gateway cluster where this IAD equipment resides should be configured.
Right Click SS Configure Management
8
IAD Gateway Cluster Configuration
9
IAD Gateway Cluster Configuration
Chennai IAD Zone=100
Area Code=44
10
Configuration of Data Area Capacity
The SPC of SS control equipment processes calls & protocols based on the gateway cluster. After a gateway cluster is added, we need to allocate an SPC for it.
Right Click SS Configure Management Globe Configuration SS Data Configuration Shelf Configuration Right Click SPC Card Data Area Capacity Configuration Click “Add”
11
Configuration of Data Area Capacity
12
Configuration of Data Area Capacity
13
Configuration of Data Area Capacity
14
Zone to Card Configuration
We must allocate services, protocols and authentication of users in the zone (gateway cluster) to the SPC board for processing.
15
Configuration of Data Area Capacity
Chennai Zone=100
SPC Card=94
16
Reboot the SPC Card
Right Click SS and Select Command Line Terminal
17
Reboot the SPC Card
Command: 1211:3, 14,”YYYYMMDD”
18
IAD Node Configuration
Double Click on the zone to which a node is added to enter the zone
19
IAD Node Configuration
Chennai Node ID=100
Chennai IAD IP=10.64.2.22
20
IAD Node Configuration
Device Property
21
IAD User Configuration
DNHM Configuration
1. Local Office Code
Click Add and Select Add Local Office Code
22
IAD User Configuration
Chennai Area Code=44
Office Code for IAD=8888
User No. Length=3
23
IAD User Configuration
2. Configuration of the Hundred Group
Click Add and Select Add Hundred Set
Click the Hundred groups to be allocated, and press [<], this hundred group will be moved to the list on the left, which means that this hundred group will be allocated to the Zone.
24
IAD User Configuration
Local Office User Configuration
User Configuration Local Office User Configuration Click “Add”
25
TID Default Attribute Configuration
Here we have to specify the default property template and packet template ID for different terminal types.
Enter in to the Zone and Select Default Attribute Configuration
26
TID Default Attribute Configuration
Click “Add” Subscriber
27
TID Default Attribute Configuration
RTP
28
Configuration of the TID Name
TID Name is the terminal ID in the H.248 protocol, used for identifying the physical termination point (user circuit) and the logic termination point (RTP Port).
29
Configuration of the TID Name
Select “Add” then “Add TID Name”
User Circuit
30
Configuration of the TID Name
RTP Port
univ.zte.com.cn