Mounting Instructions

®

VENETIA STUDIUMICARO 3 TIERS

126CAR

220-240V

INDEX

p. 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . contents of the boxp. 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . warningsp. 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . electrical connectionsp. 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . installing the fixturep. 11 . . . . . . . . . . . . . . . . . . . . . . . . . . . cleaning and maintenancep. 12 . . . . . . . . . . . . . . . . . . . . . . . . . . . cables shortening instructionsp. 13 . . . . . . . . . . . . . . . . . . . . . . . . . . . technical product sheet

structure Gelement Dcanopywith cross bar

steel cableswith carabiners

1X1X

1X 1X

small metal tip glass drop

1X 1X

large disk medium disk small disk

1X1X 1X

3

ICARO 3 TIERS - 126CAR (contents of the box)

®

WARNINGS

4

WE RECOMMEND INSTALLATION BY A LICENSED ELECTRICIAN.

. Before starting the installation, disconnect the power by turning off the circuit breaker or by removing the fuse at the fuse box.. To avoid the risk of fire, do not exceed the recommended wattage as indicated on the structure of the lamp.. Do not connect electricity until your lamp is fully assembled.. To reduce the risk of fire, electrical shock, or personal injury, always turn off and unplug the lamp and allow it to cool prior to replacing light bulbs.. Do not touch bulbs when fixture is turned on or look directly at light bulbs.. Keep flammable materials away from light bulbs.. Due to the fixture size and weight, it may be necessary for more than one person to assist in the installation of this lamp.. Never use sharp tools, rings, or other objects when installing the lamp, as they may scratch it.. Use LED LIGHTS ONLY. No other light bulbs are supported by this lamp.

GENERAL:

- Read all instructions and review diagrams beginning with the installation of the fixture.- All electrical connections must be in accordance with local codes, ordinances, or national codes. If you are unfamiliar with methods of electrical wiring, secure the services of a qualified licensed electrician.

BEFORE BEGINNING INSTALLATION:

- Turn off the electricity to the outlet box at the circuit breaker or fuse box.- If you are replacing an existing fixture, remove the old fixture and expose the supply wiring.- Remove the old cross bar.

ELECTRICAL CONNECTIONS:

a. Fix crossbar to the cealing with suitable screws.

b. Connect the blu wire from the fixture to the blu wire of the supply circuit.

c. Connect the brown wire from the fixture to the brown supply wire. Connect the ground wire - yellow/green - to the ground conductor of the supply circuit. Make sure that there are no loose strands of wire and that there are no loose connections.

ELECTRICAL CONNECTIONS

5

Due to the fixture size and weight, it may be necessary for more than oneperson to assist in the installation of this lamp.

1. Before starting the installation, disconnect the power by turning off the circuit breaker or removing the fuse at the fuse box.2. Attach the cross bar A to the ceiling with suitable screws.3. Make the electrical connections. Refer to the section titled Electrical Connections - step a.

4. Place the canopy (element B) over the nipple.

5. Screw the hook C onto the nipple and tighten securely.

INSTALLING THE FIXTURE

B

A

C

6

7

6. Hang the suspension steel cables to the hook C.

7. Lay the large disk over a flat clean surface with the larger circumference facing down. Insert element D. Tighten the three screws E1, and make sure that structure D is safely fixed to the disk.

C

DE2E2

E1 E1

L

E1E1

8. Insert the medium disk into element D. Tighten the three screws E2, and make sure that structure D is safely fixed to the disk.

9. Turn the lamp upside down and attach suspension steel cables to holes F using the carabiners.

8

D

LE2 E2E2

F

F

F

10. Unscrew L and insert the bulb holder structure G, making sure that pin H fits securely into slot I.

11. Lock the bulb holder structure D using screw L.

9

G

LD

H

I

12. Insert and twist lock the GU10 light bulb at the bottom of the bulb holder structure G and screw the light bulbs in the bulb holder structure G. Insert the plug M into the bulb holder structure G. Restore the electricity and test functionality.

13. Screw the small metal tip N onto smaller disk and make sure it is safely fixed to the disk.

10

twist lock lightbulbGU10

M

G

bulbs E27

N

14. Attach the smaller disk to the chandelier. First, fasten the small carabiner O to the hole P of one of the structure D brackets. Then, place the smaller disk, making sure that all the magnets adhere.

11

D

O

P

15. Hang the hook of the glass drop into the ring Q of the small metal tip.

Q

The decoration is handmade. Never use sharp tools, rings, or other objects when installing or cleaning the lamp, as they may scratch it.

Remove dust gently with soft brush only. This action should only be performed on the inner side of the lamp and not on thedecorated surface.

In order to handle the bulb holder structure, always removethe smaller disk and the twist lock light bulb at the bottom of the bulb holder structure first.

ICARO 3 TIERS is made by highly skilled artisans with quality inspections made in all the phases of production.Every lamp, no matter how similar it may look to another,is completely unique. No two pieces are identical.The decoration is carefully checked. Marks are not to be considered defects, but rather features that make each lamp unique andauthentic and proof of high quality craftsmanship.

CLEANING AND MAINTENANCE

12

®

CABLE SHORTENING INSTRUCTIONS

13

C

R BEFORE BEGINNING INSTALLATION,TURN OFF THE ELECTRICITY.

1. Unscrew the cylindrical screw nut R.

2. Using your fingers, press the cylindrical screw nut R down. Slide the carabiner along the steel cable to the desired length. Re-tighten the cylindrical screw nut R firmly.

Repeat operation for each cable. Measure each cable length to make sure they are all the same lengths.

3. Hook the lamp to the cables using the carabiners, and make sure it is perfectly balanced. Cut the excess off the cable ends.

4. Remove the lamp from the hook C and shorten the electrical wire according to the new cable dimensions.

b

a

c

d

a.1

TECHNICAL PRODUCT SHEET

14

a - Ceiling attachment ...................... cm 10 (4 in.) (hook included)

a.1 - Diameter ceiling attachment ..... cm 15,5 (6 in.)

b - Steel cable standard length .......... cm 86 (33 1/2 in.) minimum ........... cm 28 (11 in.) max. ................. cm 192 (74 3/4 in.)

c - Shade ......................................... cm 58 (22 3/4 in.)

d - Glass drop ................................. cm 6 (2 3/8 in.)

Diameter .................................. cm 125,5 (49 3/8 in.)

Standard overall height ............. cm 160 (62 1/2 in.) minimum ........ cm 102 (39 3/4 in.) max. ............... cm 266 (103 3/4 in.)

Material ................................... fiber glass

Weight ..................................... kg 6,7

Suggested wattage ................... 15 x 7W E27 LED dimmable + 1 x 5W GU10 LED dimmable

Do not exceed the wattage indicated on the structureof the lamp.

VENETIA STUDIUM S.r.l.

San Marco 2425 - 30124 Venezia - Italyphone: +39 041 523 6953

fax: +39 041 522 7353

www.venetiastudium.cominfo@venetiastudium.com