Jointmaker ProJMPv2

Ideal for fine cutting—— Jointmaker Pro

Secret of Jointmaker ProAs we know, the common way of cutting is simply not the best to do fine cutting of small wood stock, such as small delicate pieces and the high accuracy required for small objects. Historically, the products which can be treated as milestone in human history are born quietly. Now here is a new multi-function hand saw which overcomes impossibilities to cut small wood stock accurately, and of course can meet the needs of daily cutting easily. The whole structure of the Jointmaker pro (JMPv2) is designed from user experience, ergonomics, and industrial aesthetics, which can satisfy the multifarious imagination of woodworkers and make you a cutting master.

When John was young, he tried to make a small jewelry box and planned to add tiny steps in the small lattice to easily remove small jewelry pieces. But he found that the existing tools on the market cannot cut this kind of miniature-wood stock. Occasionally he mounted a Japanese saw blade upside down in the bench vise and pushed the wood stock to cut, and found that the cutting surface is very smooth. At that time, the "hand saw" concept began to appear.

The birth of Jointmaker Pro

JOINTMAKER PRO2009Aluminum,Stainless Steel,Maple

PRECISION FENCE SYSTEM2011Aluminum,Stainless Steel

Crosscut A‒ 28tpi

419mm

74mm

0.4mm

0.4mm

Blade length

Blade width

Blade thickness

Kerf thickness

Crosscut B‒ 32tpi

419mm

74mm

0.3mm

0.3mm

Crosscut C‒ 28tpi

419mm

74mm

0.4mm

0.58mm

Rip Blade‒ 16tpi

419mm

74mm

0.4mm

0.4mm

The whole structural design of the JMPv2 has strict requirements for accuracy, exquisite design and a strict quality control process are adopted throughout from blade design, small stop block design, leg height adjustment to material selection.

Precise cutting 1

Japanese high quality blade is suitable for all kinds of cuttingAs the core part, the high quality of the blade is the guarantee of cutting performance. After exhaustive evaluations, this Japanese blade is selected.

Normally, the heat treatment process of the blade may produce mottled colors and then be removed by grinding, but the John thinks that this gold color can be turned into a beautiful protective color by improving the process and quality control. Therefore, improving the heat treatment process and quality control management was advocated. Finally, the smooth and delicate golden appearance is achieved.

Additionally, the features of rust-resistance, wear-resistance and a superior appearance are achieved.There are four types of blades, Crosscut A is the most commonly used blade, whose kerf is as small as 0.4mm, and will satisfy most cutting requirement.Crosscut B, is best for the soft woods; Crosscut C is a little wider than Crosscut A, this blade was designed for fret wire, but it is also used for cutting dense woods; Rip Blade gives an incredible finish when ripping your stock, it can be used for dovetails making.

0.02mm Accurate adjustable stopsEach fence half has two stop blocks, the black stop is used for rough positioning, the blue one is used for accurate positioning and has a 0.02mm fine adjustment. Both fences can be flipped up and down or tilted left and right according to the planned cut.Simple adjustment of blade height, angle and tilting.

Trunnion Assembly

Keel Assembly

Simple adjustment of blade height, angle and tilting

The blade can be freely tilted via a trunnion assembly

The blade height and pitch can be easily adjusted via the keel assembly

The blade can be tilted via a trunnion assembly up to 45° by left or right side. The four included stops can set the tilt angle quickly for repeat cutting.

The adjustment mechanism of the keel assembly features gears with minimal backlash, which can not only ensure smooth rotation, but also the accurate setting of the blade height and pitch.

Special processing with selected material and strict quality control

The Fence is made of anodized aluminum, so that it is of high strength, wear resistance and rust-proof. The panel is made of PE board, which is environmental friendly, durable, and resistant to high temperatures and impacts.

The Blade Teeth are processed with a high-frequency heat treatment, so that they have high hardness and excellent cutting performance, allowing them to achieve fine cutting on various soft and hard wood.

The Stand is 14 gauge steel that is powder coated, which is wear resistant, anti-corrosion and high hardness.

7.7°

670~850mm

In the workshop, human is united with machines. In order to coordinate all the parts of the human body, the JMPv2 is also designed according to ergonomics.

The table has a tilt angle of 7.7 ° to adapt to the push of the arm. The operator does not have to bend the waist when pushing the slide table, which e�ectively reduces core fatigue. From the view of ergonomics, the tilting design of table can save energy while the arms easily complete the cutting in the extension zone.

When setting the height of stand, setting the height of table bottom as same as hip height is suggested, which can comfort the shoulder and arm while operating. From the view of ergonomics, the shoulder can be relaxed naturally by above suggested set up, which may make long work sessions more comfortable.

Ergonomic design2

The tilting angle of table is approx. 7.7° for pushing easily

The bottom of table is as same height as the hips for saving energy

-

Sliding structure moves smoothly3The JMPv2 uses cylindrical guide and linear bearing system (sealed bearing), the accuracy of parallelism of all the parts is high. The system needs no adjustment or lubrication (assembled in factory). The operation is easy with little noise, which ensures the smooth cutting experience.

Cylindrical guide is made of 40Cr steel which is T235 hardened and tempered . After chroming, the surface of the guide bar is bright, good-looking, rust-proof and hard.

The parallelism accuracy of the sliding direction of the table, the blade and the guide rail is very high. The straightness accuracy of the cylindrical guide rail is within 0.025mm. This parallelism accuracy can complete the fine cutting of the miniature stock.

A clean and tidy cut can be obtained by this sliding system. Even if you put a small piece of paper by the side of blade on the table, then pushing the fence forward and back, you cannot find any gap between the paper and blade at all.

High-hardness cylindrical guide bar with selected material

Table sliding parallel with blade

Silent linear bearing, the cutting can be operated by one handLinear sealed acetyl bearings provide a sliding process with low friction, which avoids the clogging caused by dust getting into bearings. The noise is smaller than power tools. The cutting can be completed by one-hand operation.

The JMPv2 has the innovative separated fence and separated sliding table structure. It also has various clamps and clamping ways, the only limit is your imagination!

Multi-functions make you a cutting master 4

The separated fence can tilt to different angles

Separated sliding table

The separated fence can be moved according to di�erent requirements, it can also tilt to di�erent angles on the sliding table, which can satisfy various cutting.

The JMPv2 has separated sliding tables, all the sliding tables can be slid separately or together. You can complete the fine cutting in your imagination by combining the separated fences with separated sliding tables.

Tenon miter jig and bias armThe tenon miter jig and bias arm are used to hold the wood stock. The skew angle of the bias arm is 45°. Its main work holding support tilts vertically from 0° to 90° and can also pivot horizontally for compound cuts. You can use the fence's micro-adjustment to fine-tune stock positioning.

Workholding Clamps for JointmakerThe pivot clamp is mounted on the precision fence. It can change the angle and position for your needs. The elbow clamp is fixed in the table slot to secure your work anywhere on the table. Both clamps are flexible and hold the wood stock firmly.

Wooden clamping blockIt can be used to hold the wood stock against fence quickly for cutting accurately.

Separated sliding table

Trap Fence

Stand for Jointmaker ProSD-JMP 985*695*940mm Net Weight：15.85kg

Wooden Clamping Block

Blade

Jointmaker ProJMPv2 800*412*320mm Net Weight：16.9kg

Precision Fence Bias Arm Precision Fence System (Metric/Imperial)

Precision Fence Pivot Clamp Precision Fence Elbow Clamp

Precision Fence Tenon Miter Jig Replacement Blade for JMPv2

+

28TPI

32TPI

28TPI

16TPIOptional

JMPv2

SD-JMP

PF-M

PF-I

PC-PF

EC-PF

TJ-PF

BA-PF

CBA-28

CBB-32

CBC-28

RB-16

6001001

6001002

6001003

6001008

6001004

6001005

6001006

6001007

6001009

6001010

6001011

6001012

Jointmaker Pro Gen. 2

Stand for Jointmaker Pro

Precision Fence System (Metric)

Precision Fence System (Imperial)

Precision Fence Pivot Clamp

Precision Fence Elbow Clamp

Precision Fence Tenon Miter Jig

Precision Fence Bias Arm

Replacement Blade for JMPv2 (CROSSCUT-A 28TPI)

Replacement Blade for JMPv2 (CROSSCUT B-32TPI)

Replacement Blade for JMPv2 (CROSSCUT C-28TPI)

Replacement Blade for JMPv2 (Rip Blade-16TPI)

Models Number Item Number Descriptions