This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02.
General disclaimer:The test results presented in this report relate only to the object tested.This report shall not be reproduced, except in full, without the written approval of the Issuing CB Testing Laboratory. The authenticity of this Test Report and its contents can be verified by contacting the NCB, responsible for this Test Report.
Page 2 of 14 Report No: GZES201003075201
TRF No. IEC62560C
Test item description .......................: Self-ballasted LED Lamp (LED Lamps)
Trade Mark ........................................: SONOFFManufacturer.....................................: Foshan Electrical and Lighting Co., Ltd.
64 North Fenjiang Road, Foshan, Guangdong, China.
Model/Type reference.......................: See model list in page 6
Ratings ..............................................: 220 V – 240 V; 50 Hz; other detail sees model list in page 6
Responsible Testing Laboratory (as applicable), testing procedure and testing location(s):
List of Attachments (including a total number of pages in each attachment): Attachment 1: EU Group differences (total: 1 page)Attachment 2: Circuit diagram and PCB layout (total: 3 pages);Attachment 3: EN 62493: 2015 (total 1 page)Attachment 4: Photo documentation (total: 5 pages).
Summary of testing:1. The submitted samples are in compliance with the standard EN 62560: 2012 + A1: 2015 2. The submitted appliances were found to be in compliance with the standards EN 62493: 2015, see
test report GZEM201001610504.3. Blue light hazard has been assessed according to IEC/TR 62778: 2014 and the blue light hazard is
RG0 unlimited.4. Models B02-B-A60 was selected to preformed full tests, as it has most onerous construction and
power consumption. The model B05-B-S-A60 was selected to be subjected the fault test and abnormal operation, as it has difference in PCB layout. Other models were performed construction check.
Tests performed (name of test and test clause):Clause 5 MarkingClause 6 InterchangeabilityClause 7 Protection against accidental contact with live partsClause 8 Insulation resistance and electric strength after humidity treatmentClause 9 Mechanical strengthClause 10 Cap temperature riseClause 11 Resistance to heatClause 12 Resistance to flame and ignitionClause 13 Fault conditionsClause 14 Creepage distances and clearancesClause 15 Abnormal operationClause 17 Photobiological safety
Testing location:198 Kezhu Road, Science City, Economic & Technology Development Area, Guangzhou, Guangdong, China
Summary of compliance with National Differences (List of countries addressed):EU Group differences was considered.
The product fulfils the requirements of EN 62560: 2012 + A1: 2015.
Page 4 of 14 Report No: GZES201003075201
TRF No. IEC62560C
Copy of marking plate:The artwork below may be only a draft. The use of certification marks on a product must be authorized by the respective NCBs that own these marks.
Representative
Printed on enclosure
Remark:
1. The height of “ ” symbol is not less than 7 mm;
2. The height of CE symbol is not less than 5 mm;3. According to the standard, warning and text required by the standard should be written in the official
language(s) of the country in which the appliance is to be sold. The applicant should ensure that the samples in future production fulfill the requirement;
4. As declared by the applicant, the importer (and manufacturer, if it is different)’s name, registered trade name or registered trade mark and the postal address will be marked on the products before being place on the market. The contact details shall be in a language easily understood by end-users and market surveillance authorities;
5. Marking on the packaging or in a document accompanying the electrical equipment is only acceptable if it is not possible to place such markings on the product.
6. Other models have similar label as above, just model no., wattage, CCT and rated current are different.
7. The luminous flux is declared by client.
Page 5 of 14 Report No: GZES201003075201
TRF No. IEC62560C
Test item particulars..................................................:
Classification of installation and use ......................: —
Supply Connection ....................................................: E27, B22d Lamp cap
Mass of the equipment...… .......................................: Max. 0,06 kg (series 2)
Possible test case verdicts:- test case does not apply to the test object ...........: N/A
- test object does meet the requirement..................: P (Pass)
- test object does not meet the requirement ...........: F (Fail)
Testing.........................................................................:Date of receipt of test item ........................................: 2020-10-30
Date (s) of performance of tests ...............................: 2020-10-30 to 2020-12-15
General remarks:
"(See Enclosure #)" refers to additional information appended to the report."(See appended table)" refers to a table appended to the report.
Throughout this report a comma / point is used as the decimal separator.
This document is issued by the Company subject to its General Conditions of Service, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
Manufacturer’s Declaration per sub-clause 4.2.5 of IECEE 02:
The application for obtaining a CB Test Certificate includes more than one factory location and a declaration from the Manufacturer stating that the sample(s) submitted for evaluation is (are) representative of the products from each factory has been provided ...............................................................:
Yes Not applicable
When differences exist; they shall be identified in the General product information section.
Page 6 of 14 Report No: GZES201003075201
TRF No. IEC62560C
Name and address of factory (ies) ..........................: Same as manufacture
General product information and other remarks:1. Self-ballasted LED lamp.2. The LED lamps have non-SELV drivers, integrated with E27, B22d lamp cap and they cannot be used
in the dimmable circuit. For dry location use only. 3. They can dimmer by cell phone APP
Model list:Model Power Input current Lamp cap Series Blue Light
Hazard
B01-B-A60 9 W 75 mA E27
B01-B-S-A60 9 W 75 mA B22d
B02-B-A60 9 W 75 mA E27
B02-B-S-A60 9 W 75 mA B22d
The color temperature 2700 K - 6500 K.Series 1 have the same construction circuit diagram and PCB layout, only different in the lamp cap
Series 1 RG0
B04-B-A60 9 W 75 mA E27
B04-B-S-A60 9 W 75 mA B22d
B05-B-A60 9 W 75 mA E27
B05-B-S-A60 9 W 75 mA B22d
Series 2 have the same construction circuit diagram and PCB layout, only different in the lamp cap
Series 2 RG0
1, All models can dimmer by cell phone APP;2, where the model name includes “TW” mean the lamp can controller the colour temperature by cell phone APP3, where the model name includes “RGB” mean the lamp can controller the colour by cell phone APP
Page 7 of 14 Report No: GZES201003075201
IEC 62560
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC62560C
4 GENERAL REQUIREMENTS P
4.1 The lamp shall be so designed and constructed that in normal use cause no danger to the user.
P
4.2 Self-ballasted LED-Lamp are non-repairable. P
5 MARKING P
5.1 Mandatory marking P
- mark of origin P
- rated supply voltage (V).........................................: 220 -240 V P
- rated wattage (W) ..................................................: See model list in page 4 P
- rated frequency (Hz)..............................................: 50 Hz P
5.2 Addition marking P
- rated current (A) ....................................................: See model list in page 4 P
- weight significantly higher P
- special conditions or restrictions P
Not suitable for dimming; symbol used
P
- not suitable for water contact P
5.3 Marking durable and legible P
rubbing 15 s water, 15 s petroleum; marking legible P
6 INTERCHANGEABILITY P
6.1 Cap interchangeability in accordance with IEC 60061-1 P
Gauge in accordance with IEC 60061-3 P
6.2 Bending moment and mass imparted by the lamp at the lampholder P
Bending moment imparted by the lamp at the lampholder (Nm) ....................................................:
Max. 0,0078 Nm for B22d lamp cap (for B02-B-S-A60)Max. 0,0079 Nm for E27 lamp cap (for B05-B-A60)
P
Mass not exceeding value table 2 or as specified in IEC 60061-1 (kg).....................................................:
Max 0.09 kg for B22d lamp cap (for B02-B-S-A60)Max 0.09 kg for E27 lamp cap(for B05-B-A60)
P
Page 8 of 14 Report No: GZES201003075201
IEC 62560
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC62560C
7 PROTECTION AGAINST ACCIDENTAL CONTACT WITH LIVE PARTS P
Internal, basic insulated or live metal parts not accessible
P
Tested with a test finger with a force of 10 N P
Compliance checked with appropriate gauges P
8 INSULATION RESISTANCE AND ELECTRIC STRENGTH P
8.2 After storage 48 h at 91-95% relative humidity and 20-30 C measuring of insulation resistance with d.c. 500 V (M):
P
4 M for double or reinforced insulation ..............: 20 M P
8.3 Immediately after clause 8.2 electric strength test for 1 min P
Double or reinforced insulation, 4U + 2000 V P
No flashover or breakdown P
9 MECHANICAL STRENGTH P
9.2.1 Torsion resistance of unused lamps P
B15d or E14 Cap........................................1,15 Nm N/A
B22d, E26, E26d or E27 Cap .......................3,0 Nm E27 and B22d lamp cap P
E11 or E12 Cap............................................0,8 Nm N/A
Clause 8 shall comply after the mechanical strength test.
P
9.4 Axial strength of Edison caps P
After full insertion into the gauge an axial force of Table 4 is applied to the central contact (N) ..........:
120 N for E27 lamp cap P
The insulation around the central contact shall remain intact
P
10 CAP TEMPERATURE RISE P
The cap temperature rise Δts of the lamp shall not exceed 120 K.
For E27: 72,5 °C;For B22: 73,8 °C
P
Page 9 of 14 Report No: GZES201003075201
IEC 62560
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC62560C
11 RESISTANCE TO HEAT P
Parts of insulating material providing protection against electric shock, retaining live parts in position, ball-pressure test:
(see appended table) P
12 RESISTANCE TO FLAME AND IGNITION P
External parts of insulating material preventing electric shock glow-wire test 650 C
(see appended table) P
13 FAULT CONDITIONS P
13.2 Fault conditions: where diagram indicates fault condition impairs safety, electronic components have been short-circuited or disconnected
(see appended table) P
13.3 When operated under fault conditions the lamp P
- does not emit flames or molten material P
- does not produce flammable gases or smoke P
- live parts not accessible P
After the tests the insulation resistance with d.c. 1000 V complies with requirements of Cl. 8.1.........:
20 M P
14 (16) CREEPAGE DISTANCES AND CLEARANCES P
Creepage distances and clearances according to IEC 61347-1
(see appended table) P
Conductive accessible parts according to IEC 60598-1
(see appended table) P
15 ABNORMAL OPERATION P
Non-dimmable self-ballasted lamps are tested on a dimmer or an electronic switch according the test circuit shown in Figure 8
P
Operate the lamp for 8 h at most onerous dimming level
P
When operated under abnormal operation the lamp P
- does not catch fire P
- does not produce flammable gases P
- live parts not accessible P
Page 10 of 14 Report No: GZES201003075201
IEC 62560
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC62560C
16 TEST CONDITIONS FOR DIMMABLE LAMPS N/A
Test are carried out at maximum power setting for Clause 10 and Clause 17
N/A
17 PHOTOBIOLOGICAL SAFETY P
17.1 UV radiation N/A
The LED lamp doesn’t exceed 2mW/klm N/A
17.2 Blue light hazard P
Assessed according to IEC TR 62778 P
LED lamps shall be RG0 or RG1 RG0 P
18 INGRESS PROTECTION N/A
18.1 Lamps shall be suitable for water contact unless marked with Figure 6
N/A
18.2 The lamp is subjected to an IPX4 test according to IEC 60598-1
N/A
The lamp complies with the compliance provisions of 9.2 of IEC 60598-1
N/A
Lamps constructed so that it is sealed to exclude water need not to be tested
N/A
Page 11 of 14 Report No: GZES201003075201
IEC 62560
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC62560C
12 TABLE: Resistance to heat and fire - Glow wire tests
Glow wire test (GWT); (°C) Verdict
650
Object/Part No./Material
Manufacturer/trademark
te ti
PCB See annex 1 0 0 P
Lamp shade See annex 1 0 0 P
Connector on PCB See annex 1 0 0 P
Plastic enclosure See annex 1 0 0 P
Plastic material between lamp cap
See annex 1 0 0 P
13 TABLE: tests of fault conditions (for B02-B-A60 in series 1) P
Part Simulated fault Hazard
LED Shorted circuit; LED cut off, recoverable when the fault removed NO
CE3 Shorted circuit; circuit protection, recoverable when the fault removed NO
CE2 Shorted circuit; fuse broken, non-recoverable when the fault removed NO
D1 Shorted circuit; circuit protection, recoverable when the fault removed NO
D2 Shorted circuit; circuit protection, recoverable when the fault removed NO
U1 Shorted circuit; circuit protection, recoverable when the fault removed NO
DB1 Shorted circuit; fuse broken, non-recoverable when the fault removed NO
DB1 Open circuit; no work, recoverable when the fault removed NO
11 TABLE: Ball Pressure Test of Thermoplastics P
Allowed impression diameter (mm) .................: ≤2 mm
Object/ Part No./ Material Manufacturer/trademark
Test temperature (C) Impression diameter (mm)
PCB See annex 1 125 0,51
Lamp shade See annex 1 90 0,96
Plastic enclosure See annex 1 125 1,35
Plastic material between lamp cap
See annex 1 125 1,6
Supplementary information:
Page 12 of 14 Report No: GZES201003075201
IEC 62560
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC62560C
13 TABLE: tests of fault conditions (for B05-B-A60 in series 2) P
Part Simulated fault Hazard
LED Shorted circuit; LED cut off, recoverable when the fault removed NO
CE2 Shorted circuit; fuse broken, non-recoverable when the fault removed NO
CE3 Shorted circuit; fuse broken, non-recoverable when the fault removed NO
CE4 Shorted circuit; power increase, recoverable when the fault removed NO
D1 Shorted circuit; circuit protection, recoverable when the fault removed NO
D3 Shorted circuit; normally work, no damage, recoverable when the fault removed NO
U1 Shorted circuit; circuit protection, recoverable when the fault removed NO
DB1 Shorted circuit; fuse broken, non-recoverable when the fault removed NO
DB1 Open circuit; no work, recoverable when the fault removed NO
14 TABLE: Clearance And Distance Measurements (series 1) P
clearance cl and creepage distance dcr at/of:
Up(V)
U r.m.s. (V)
Required cl (mm)
cl (mm)
required dcr (mm)
dcr(mm)
L to N on PCB 240 1,5 3,3 2,5 3,3
Live part and enclosure 240 3 >6,5 5 >6,5
Supplementary information:
14 TABLE: Clearance And Creepage Distance Measurements (series 2) P
clearance cl and creepage distance dcr at/of:
Up(V)
U r.m.s. (V)
Required cl (mm)
cl (mm)
required dcr (mm)
dcr(mm)
L to N on PCB 240 1,5 3,3 2,5 3,3
Live part and enclosure 240 3 >6,5 5 >6,5
Supplementary information:
Page 13 of 14 Report No: GZES201003075201
IEC 62560
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC62560C
ANNEX 1 TABLE: Critical components information
Object / part No. Code Manufacturer/
trademark Type / model Technical data Standard Mark(s) of conformity1)
B Bridgelux. Inc. LED Lighting
2835 Vf: 17,0~20,0 V; If: 30 mA; 2700-6500 k
EN 62560 Tested with appliance
LED
D EVERLIGHT 2835 Vf: 17,0~20,0 V; If: 30 mA; 2700-6500 k
EN 62560 Tested with appliance
B Quanzhou Jintian Electronic circuit board Co., Ltd.
JAL-5,JAL-6
V-0; 130 °C EN 62560 UL E239807 & Tested with appliance
D Jiang xi Leadfly Circuit Co., Ltd.
LD-8 V-0; 130 °C EN 62560 UL E333645 & Tested with appliance
Aluminum PCB
D Guang Zhou Hong Yu Electronic Co., Ltd.
HY-5, HY-6, HY-8
V-0; 130 °C EN 62560 UL E309772 & Tested with appliance
Input wire B FoshanJianQiang Electronic & Electrical Co., Ltd.
3135 200 °C; 600 Vac, 24 AWG
EN 62560 UL E256415 & Tested with appliance
Lampshade B Dongguan Powide Opto-Electronic&Heat Dissipation Technology Co., Ltd.
PA-AF0915 V-0 EN 62560UL E487857 & Tested with appliance
B Shunde Junda Electronic Co., Ltd.
JD-E V-0 EN 62560 UL E173873 & Tested with appliance
D Guangdong Hetong Technology Co., Ltd.
FR4, CEM1
V-0 EN 62560 UL E243157 & Tested with appliance
Driver PCB
D Allfavor Circuits (Shenzhen) Co., Ltd.
AF-M1 V-0 EN 62560 UL E301546 & Tested with appliance
Page 14 of 14 Report No: GZES201003075201
IEC 62560
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC62560C
D Ruihua Printed Circuit Board Co., Ltd.
RH-NS,RH-K5
V-0 EN 62560 UL E148158 & Tested with appliance
D Tongling Huake Electronic Material Co., Ltd.
FR-4.0,CEM3
V-0 EN 62560 UL E212661 & Tested with appliance
D Wode Electronics Technology (Zhuhai) Co., Ltd.
RXD-11, WD-12,WD-13
V-0 EN 62560 UL
E323980 & Tested with appliance
Fuse B Shenzhen Great Electronics Co., Ltd.
RXF-1W 15 Ω; 1 W EN 62560 UL E301541 & Tested with appliance
Supplementary information:1) Provided evidence ensures the agreed level of compliance. See OD-CB2039.The codes above have the following meaning:A - The component is replaceable with another one, also certified, with equivalent characteristics B - The component is replaceable if authorised by the test houseC - Integrated component tested together with the applianceD - Alternative component
- - - End of main report - - -
Page 1 of 1 Report No: GZES201003075201
Attachment 1: EU Group differences
Clause Requirement + Test Result - Remark Verdict
CENELEC COMMON MODIFICATIONS (EN)
Annex ZA (normative)
Normative references to international publications with their corresponding European publications
Lamps with the following caps are excluded from EN 62560:2012/A1:2015 as they do not comply with European safety requirements:E11; E12; E17; E26; E26d; E39
