IEEE-1588 DEPLOYED ON THE EASTERN RANGEHummingbird HostExplorer Open Session Dell OpenManage Server...

42nd

Annual Precise Time and Time Interval (PTTI) Meeting

343

IEEE-1588 DEPLOYED ON THE EASTERN RANGE

Wayne L. Rendla

L-3 Communications

SpaceLift Range Systems Contract (SLRSC), PO Box 254307,

Patrick Air Force Base, FL 32925, USA

Tel: 321-494-7156, E-mail: Wayne.Rendla at itt.com

James L. Wright

L-3 Communications

SLRSC, PO Box 254307, Patrick Air Force Base, FL 32925,

Tel: 321-494-1530, E-mail: Jim.Wright at itt.com

Abstract

The Air Force has installed a pilot program at the Eastern Range where new IEEE 1588

enabled GPS Timing receivers have been deployed at Cape Canaveral Air Force Station,

Kennedy Space Center, and Patrick Air Force Base and are performance monitored,

independently of GPS. This is the first known deployment of IEEE 1588 where Master and

Slave IEEE 1588 devices have been installed on a single Ethernet network, over such a large

area. The IEEE 1588 Grandmaster is located in the operations control center and is disciplined

by a cesium steered by USNO via Two-Way Satellite Time Transfer System. An automated

workstation at the operations control center collects health and status from the GPS receivers.

GPS – IEEE 1588 difference data are also collected to validate that GPS timing signals

provided to remote instrumentation are accurate within ± 2 microseconds. This paper will

describe the recently deployed system and share some of the early performance data collected.

INTRODUCTION

The Eastern Range (ER) has used Synchronized Time Code Generators (STCGs) to provide timing

signals to remote instrumentation sites. For many years, land line and RF distribution of Inter-Range

Instrumentation Group (IRIG) standard time-of-year were the synchronizing signals of choice. In recent

years, many ER remote Timing sites’ STCGs have been replaced with modern GPS Timing Receivers

capable of providing locally required time codes, repetition rates, and precision frequencies. All these

methods required the use of portable clock to verify time accuracy of signals provided to remote

instrumentation systems. Several efforts were made to implement a scheme to verify the timing accuracy

of remote Timing sites’ clocks from a central operations center. Until the introduction of the Institute of

Electrical and Electronics Engineers (IEEE) 1588 Precise Time Protocol (PTP) standard, every scheme

was too expensive or inaccurate to justify its implementation. This paper describes the IEEE 1588

implementation on the ER intended to provide real-time, time accuracy verification of remote timing

sites.

Report Documentation Page Form ApprovedOMB No. 0704-0188Public reporting burden for the collection of information is estimated to average 1 hour per response, including the time for reviewing instructions, searching existing data sources, gathering andmaintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information,including suggestions for reducing this burden, to Washington Headquarters Services, Directorate for Information Operations and Reports, 1215 Jefferson Davis Highway, Suite 1204, ArlingtonVA 22202-4302. Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to a penalty for failing to comply with a collection of information if itdoes not display a currently valid OMB control number.

1. REPORT DATE NOV 2010

2. REPORT TYPE N/A

3. DATES COVERED -

4. TITLE AND SUBTITLE IEEE-1588 Deployed on the Eastern Range

5a. CONTRACT NUMBER

5b. GRANT NUMBER

5c. PROGRAM ELEMENT NUMBER

6. AUTHOR(S) 5d. PROJECT NUMBER

5e. TASK NUMBER

5f. WORK UNIT NUMBER

7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) L-3 Communications SpaceLift Range Systems Contract (SLRSC), POBox 254307, Patrick Air Force Base, FL 32925, USA

8. PERFORMING ORGANIZATIONREPORT NUMBER

9. SPONSORING/MONITORING AGENCY NAME(S) AND ADDRESS(ES) 10. SPONSOR/MONITOR’S ACRONYM(S)

11. SPONSOR/MONITOR’S REPORT NUMBER(S)

12. DISTRIBUTION/AVAILABILITY STATEMENT Approved for public release, distribution unlimited

13. SUPPLEMENTARY NOTES See also ADA547222. Precise Time and Time Interval (PTTI) Systems and Applications Meeting (42ndAnnual) Held in Reston, Virginia on November 15-18, 2010, The original document contains color images.

14. ABSTRACT The Air Force has installed a pilot program at the Eastern Range where new IEEE 1588 enabled GPSTiming receivers have been deployed at Cape Canaveral Air Force Station, Kennedy Space Center, andPatrick Air Force Base and are performance monitored, independently of GPS. This is the first knowndeployment of IEEE 1588 where Master and Slave IEEE 1588 devices have been installed on a singleEthernet network, over such a large area. The IEEE 1588 Grandmaster is located in the operations controlcenter and is disciplined by a cesium steered by USNO via Two-Way Satellite Time Transfer System. Anautomated workstation at the operations control center collects health and status from the GPS receivers.GPS â IEEE 1588 difference data are also collected to validate that GPS timing signals provided to remoteinstrumentation are accurate within Â± 2 microseconds. This paper will describe the recently deployedsystem and share some of the early performance data collected.

15. SUBJECT TERMS

16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT

SAR

18. NUMBEROF PAGES

16

19a. NAME OFRESPONSIBLE PERSON

a. REPORT unclassified

b. ABSTRACT unclassified

c. THIS PAGE unclassified

Standard Form 298 (Rev. 8-98) Prescribed by ANSI Std Z39-18

42nd


344

THE SYSTEM

The Timing Health and Analysis Monitor System (THAMS) consists of the THAMS Server/Workstation

and the Grandmaster IEEE 1588 clock located in the Morrell Operations Center (MOC), and

Member/Slave IEEE 1588 clocks located at sites located at Cape Canaveral Air Force Station (CCAFS),

Patrick Air Force Base (PAFB), and Kennedy Space Center (KSC). The THAMS Server/Workstation

and Grandmaster/Member IEEE 1588 Clocks are connected via dedicated single fiber-optic strands,

Ethernet switches, and media converters. The Grandmaster IEEE 1588 clock receives its initial

synchronization from the Global Positioning System (GPS), and then maintains time by accepting 10

megahertz (MHz) from the Range Clock in the MOC, which is synchronized and syntonized to the

Department of Defense Master Clock (DOD MC) at US Naval Observatory, via the Two-Way Satellite

Time Transfer System. The primary function of the GPS Receivers at remote instrumentation sites is to

provide specification compliant time to Range instrumentation. The THAMS enables operators to

remotely verify the accuracy of time provided to Range users by comparing the times from GPS and

IEEE 1588 at each Site Clock. Site Clock time accuracy measurement was expected to be in the

microsecond range.

THE COMPONENTS

The significant component of the THAMS is the GPS Receiver assembly that is based on Symmetricom

XLi IEEE 1588 Clock. This is a commercial-off-the-shelf item, which is installed with an antenna, in-

line amplifier for cable lengths greater than 150 feet, antenna cable, two lightning arrestors, and the

necessary hardware and adapters for installation and interface to the existing building structure and timing

equipment. The GPS Receiver assembly has a Grandmaster IEEE 1588 plug-in module in Bay 4, a

Member/Slave1588 plug-in module in Bay 2, a four-channel sine wave frequency output plug-in module

in Bay 3, and a GPS Engine plug-in module in Bay 1.

42nd


345

GPS Receiver

(Primary)

1 pps

B003

1 MHz

Site

Clock

Timing

Equipment

Ethernet

Switch

Ethernet

Switch

File: Time Monitor Sys BD 20091119A.ppt

Fiber Optic

single strand

Site Clocks Infrastructure Range Clock

1

m

x

n

Timing

Health

and

Analysis

Monitor

System

(THAMS)

Server/

Workstation

Operator

Commands and

Requests

Health,

Status and

Performance

B123

NET

Management port

1588 PTP

Member/slave port

GPS Receiver

(Standby)

1588 PTP Master port

Grandmaster

J3 Auxiliary Reference

Frequency (Primary)

10MHz

Signals as

required

1 pps

J1 TIET

Performance

measurement

Member

Primary Frequency

Reference

(Independent of GPS)

Media Converter

Management

Media Converter,

Copper to Fiber

Media Converter

Management NET

Management port

Bay 2Bay 4

Bay 3

CODE

1PPS

Figure 1. THAMS block diagram.

THE SOFTWARE

The THAMS Server/Workstation provides the operator a graphical user interface (GUI) to monitor,

configure, and observe status of the GPS Receivers, Transition Networks, Inc., Media Converters, Cisco

IE3000 Switches, and Dell PowerEdge 2950 III Server. The following software operating system and

applications are installed on THAMS to provide for health, status, and control of the GPS Receivers and

the Ethernet components:

THAMS Software

Hewlett-Packard (HP) NNM 8i

Symmetricom TimeMonitor XLi Software

Symmetricom TimeMonitor Analyzer Software

Rainbow Technologies Sentinel

Transition Networks Focal Point 2.1 Management Software

Hummingbird Connectivity Secure Shell Management Console

42nd


346

Hummingbird HostExplorer Open Session

Dell OpenManage Server Administrator.

The Symmetricom TimeMonitor XLi Software allows for monitoring the status of the GPS Receivers and

capturing timing performance data. Once data collection is initiated, it will continue without manual

intervention until an operator stops the collection, or data storage limit is reached (approximately 11 days

of data is the longest collection period to date). However, if some event or failure disrupts collection and

prevents the normal closing of the file, then all data since the start of collection are lost. The data

collected may be saved to a file for additional analysis with the Symmetricom TimeMonitor Analyzer

software application. The collected data may also be opened with Microsoft (MS) Excel 2007 as a

delimited text file to a text file for further viewing and analysis. The Rainbow Technologies Sentinel

application is loaded before the hardware universal serial bus (USB) key is installed. The hardware USB

key is required to open the Symmetricom TimeMonitor applications.

THE SERVER/WORKSTATION

THAMS is implemented on a Dell PowerEdge Server Model 2950 III running MS Windows 2008 Server

64-Bit operating system. The computer has the following components:

THAMS Server Hardware Components

Rackmount Chassis (2-rack units high, 19-inches wide)

Dual Core XEON Processor: 2.0-gigahertz (GHz), 1333-megahertz (MHz) front-side bus, L2 cache

System Memory: 8-gigabyte single-ranked Dual In-line Memory Modules

Two 146- gigabyte Removable Hard Drives

Optical Drive: Digital Versatile Disc – Rewriteable, Serial Advanced Technology Attachment, Internal

Two Redundant, Server Power Supplies

Two 10/100/1000 Network Interface Cards.

Communication Equipment

Cisco IE3000 Ethernet Switch (SW)

Transition Networks Media Converter.

LOCATION

Figure 3 shows a portion of Brevard County, Florida. THAMS equipment is located at Kennedy Space

Center (KSC), Cape Canaveral Air Force Station (CCAFS), and Patrick Air Force Base (PAFB). The

42nd


347

figure shows the general location of the Morrell Operations Center (MOC) and the remote

instrumentation sites. The system extends from the Radar 0.134 at Patrick Air Force base north 33 miles

to the Playalinda Beach Distance Object Attitude Measurement System (DOAMS) north of the National

Aeronautics and Space Administration (NASA) Shuttle launch pads. The east-west distance from the

Range Communications Bldg to the Radar 19.14 is over 5 miles. The cable path from the Radar 0.134 to

the MOC is approximately 15.9 miles. The cable distance from the MOC to the most distance site, the

Playalinda Beach DOAMS, is approximately 21.3 miles.

Playalinda Beach DOAMS

Patrick AFB DOAMS

Radar 0.134

Patrick Base Communications, Bldg 533

Launch Control Center, KSC

Central Instrumentation Facility, KSC

Range Communications (XY) Bldg

Telemetry site 4

Radar 19.14

Delta II Operations Bldg

Morrell Operations Center

Complex 30

Test Operations Facility

Guidance Test Facility

Atlantic Ocean

CCAFS

KSC

PAFB

Brevard CountyFlorida

IndianRiverLagoon

BananaRiverLagoon

File: THAMS_map_20101004.pptx

33 miles

5.6 miles

Figure 3. THAMS general location map.

THE ENVIRONMENT

The environment is depicted outside the circle in Figure 4. Two independent means of time transfer from

USNO provides assurance that systemic problems are detected. The GPS receiver provides the timing

signals needed at the remote instrumentation site. The operator submits requests current status and past

performance data. The THAMS responds by saving requested performance data for later analysis and

display of health and status data for immediate assessment.

42nd


348

The block diagram shown in Figure 5 provides network details. Single fibers are identified by the locally

assigned reference designator. Full duplex media converter pairs convert the optical signals into the

copper circuits at each Ethernet Switch (SW). Media converter and Ethernet Switch management ports

have been omitted from this figure. All remote site GPS receivers are two, three, or four Ethernet

Switches from the IEEE 1588 Grandmaster. The Ethernet Switches support either IEEE 1588 version 1

or version 2. However, since the GPS Receivers can support only IEEE 1588 version 1 at this time, the

Ethernet Switches are configured for IEEE 1588 version 1 support.

1

GPS Signals

Grandmaster

Remote Site Clock

IEEE 158810 MHz

Reference

Frequency Performance

Data

Commands

Status, Faults and

Performance Data

GPS 1 PPS

IEEE 1588

1 PPS

Health is an indicator of

the condition of equipment.

Time Interval

Event Time

(Time-of-Year,

Frequencies

and Rates)

THAMS Server/

WorkstationOperator

Requests

Timing Signals

Health

and

Status

Member/

Slave

Analyst

Operator

USNO

TWSTT

Figure 4. THAMS environment diagram.

SYSTEM ATTRIBUTES

The THAMS provides ER Timing Operators with a central monitoring capability where remote timing

sites can be monitored for health, status, and time accuracy performance. The THAMS embedded

Network Node Manager receives Simple Network Management Protocol real-time trap notification

messages from Ethernet enabled devices, which are presented on the THAMS workstation/server monitor.

42nd


349

With a simple glance at the monitor, operators can determine the health and status of the network and the

devices connected to it. Real time GPS – IEEE 1588 time difference data for each remote site are also

available on the THAMS monitor. And there are Web interfaces to the Ethernet enabled devices that can

be accessed to obtain detailed health and status and to effect configuration changes. This deployment of

IEEE 1588 is successfully deployed over the largest known-to-date campus (approximate size of 175

square miles).

File: THAMS_ICD_Infrastructure_20091119.ppt

Site Clocks

THAMS

Server/

Work-

station

1

4

5

6

7

8

9

10

11

12

13

14

15

2

3

Playalinda Beach

DOAMS

LCC, KSC

CIF, KSC

Tel-4

Tel-4

19.14 Radar

Range

Communications

(XY)

CX30

TOF

GTB

1SLSOB

MOC

Grandmaster

PAFB 533

PAFB DOAMS

PAFB 0.134

Radar

LCC CX30 Tel-4 PAFB XY MOC

6DAC5603

6DAC5602

6DAC5601 6FO4800

6DAC5600

6FO4801

BRRS

KSC CCAFS

6FO4805

6FO4807

DDE00028

DDE00027Ethernet Switch (SW)

Media Converter (MC)

6DAC5604

SW

6FO4802

6FO4803

6FO4804

B423

PAFB CCAFS

6FO4812

DDE00029

SW

SW

SW

SW

SW

SW

SW

SW

SW

SW

SWSW

SW

GPS Receiver

Assembly

Infrastructure Fiber Optic single strand

Figure 5. THAMS block diagram.

DATA COLLECTION

The data are collected in a .xli format compatible text format. See Figure 6 for a GPS – IEEE 1588 time

difference data sample. As the figure shows, the time stamps are not monotonically increasing. This is

the result of time-interval values either less than 1 second, or greater than 1 second. The first case results

in two values captured in the same second. In the second case, no value is captured in the intervening

second.

The Symmetricom TimeMonitor Xli software includes a utility TimeMonitor Analyzer for graphing and

analysis of the data. This tool was used to graphically display the data in the following figures.

42nd


350

285:11:59:45.999999735

285:11:59:46.999999680

285:11:59:48.000000780

285:11:59:49.000000730

285:11:59:50.000001175

285:11:59:51.000001070

285:11:59:52.000000085

285:11:59:52.999999975

285:11:59:53.999999070

285:11:59:54.999998960

285:11:59:55.999998945

285:11:59:56.999998840

285:11:59:57.999999785

285:11:59:58.999999675

285:12:00:00.000000530

285:12:00:01.000000425

285:12:00:02.000000435

285:12:00:03.000000330

285:12:00:04.000000005

285:12:00:04.999999895

285:12:00:05.999999790

285:12:00:06.999999685

285:12:00:07.999999585

285:12:00:08.999999485

285:12:00:10.000000000

Legend“missing”second,interval greater thanone second

“Extra” second,interval lessthan one second

Figure 6. Data sample.

RESULTS AND DATA ANALYSIS

Figure 7 represents TimeMonitor Analyzer data collected from one of the remote timing sites for a period

of 6 days. Evidently there are 15 time difference data excursions where the data indicates that the time

difference between GPS and IEEE 1588 at the remote timing site approaches ± 6 milliseconds. Though

rare, these time differences have been observed to approach 500 milliseconds. Expanding the X axis for

the data set, such as Figure 8 for 1 hour/division, and Figure 9 for 10 minutes/division, additional time

difference data excursions are observed. Not until “quiet” data are observed in presentation format for 1

minute/division (Figure 10) can data for each time difference measurement be observed without

excursion. From these data, one must conclude that the goal of verifying time accuracy performance

with less than 2-microsecond precision cannot be achieved in real time.

42nd


351

Figure 7. Remote site data (6 days, 12 hours per division).

42nd


352

Figure 8. Remote site data (15 hours, 1 hour per division).

42nd


353

Figure 9. Remote site data (1.6 hours, 10 minutes per division).

42nd


354

Figure 10. Remote site data (10 minutes, 1 minute per division).

Postprocessing of the time difference data was performed using the technique of removing outlier time

difference data that exceeds 3 times the standard deviation from the mean value. This technique has to be

applied for most data sets 2 to 4 times, effectively eliminating 1 to 3 percent of data collected, to

determine a nominal time difference data set for the remote timing sites. With the above postprocessing,

remote timing site time accuracy performance, with a precision of less than 2 microseconds, can be

achieved in most cases. However, time difference data excursions of 8 microseconds still are evident. Reference Figure 11.

42nd


355

Figure 11. Plot with outliers removed (6 days, 12 hours per division).

POTENTIAL IMPROVEMENTS

The Symmetricom XLi GPS Receiver lacks secure protocols, which pose significant Information

Assurance issues for Air Force installations. Symmetricom reports that they will ultimately provide

secure protocol upgrades for the XLi GPS Receiver. However, at this time the release date for this

upgrade is unknown.

The source(s) of the GPS – IEEE 1588 time difference data excursions are unknown. Potentially

upgrading the GPS Receivers and THAMS network to use IEEE 1588 version 2 will alleviate these data

anomalies. Symmetricom reports that IEEE 1588 version 2 for the XLi GPS Receivers is planned.

However at this time, the release date for this upgrade is unknown. Other potential upgrades should be

considered if there is sufficient potential that the time data excursions can be mitigated.

42nd


356

SUMMARY AND CONCLUSION

The ER has deployed IEEE 1588 over the largest campus known by the authors of this paper. Unlike

many IEEE 1588 applications where IEEE 1588 is used to distribute precise time over a network, the

main application for this network is to provide a real-time means for monitoring the time accuracy

performance of remote timing systems. These remote timing sites use IEEE 1588-enabled GPS Receivers

to provide timing signals to ER instrumentation across Cape Canaveral Air Station, Patrick Air Force

Base, and Kennedy Space Center. The THAMS network provides improved health, status, and time

accuracy performance monitoring. In that, real-time monitoring of remote timing sites has been achieved.

However, this system has not achieved the goal of monitoring, in real time, time accuracy performance of

remote timing sites with a precision of better than 2 microseconds. The GPS – IEEE 1588 time difference

data excursions are problematic and their causes are unknown by the authors. Further investigation is

warranted.

Acronyms List

1SLSOB 1st Space Launch Squadron Operations Building (Squadron was disbanded and

facility is now called the Delta II Operations Building)

CCAFS Cape Canaveral Air Force Station

CIF Central Instrumentation Facility

DOAMS Distant Object Attitude Measurement System

DOD MC Department of Defense Master Clock

ER Eastern Range

Gb/s Gigabits per second

GPS Global Positioning System

GTB Guidance Test Building

HP Hewlett-Packard

IEEE Institute of Electrical and Electronics Engineers

IP Internet protocol

IRIG Inter-Range Instrumentation Group

42nd


357

KSC Kennedy Space Center

LCC Launch Control Center

Mb/s megabits per second

MHz megahertz

MC Media Converter

MOC Morrell Operations Center

MS Microsoft

PAFB Patrick Air Force Base

pps pulse per second

PTP Precise Time Protocol

RF radio frequency

SLRSC Spacelift Range System Contract

STCG Time Code Generators

SW Switch assembly

Tel-4 Central Telemetry Station

THAMS Timing Health and Analysis Monitor System

TOF Test Operations Facility

XY Range Communications (building)

42nd


358

Date post:	12-Feb-2021
Category:	Documents
Upload:	others
View:	0 times
Download:	0 times

IEEE-1588 DEPLOYED ON THE EASTERN RANGEHummingbird HostExplorer Open Session Dell OpenManage Server...

Documents