Ieee802 Standards

4/22/2014 ieee802 standards

http://www.eeherald.com/section/design-guide/ieee802_3.html 1/13

ieee802 standards

IEEE 802.3

Brief background of IEEE802 standards for LAN and MAN

While connecting computers through networks we need to have set of

rules/standards for the data to travel from one computer to other computer. The

right example for this can be road traffic rules. It's self understood, why we need

traffic rules while driving, in same sense for the data packets to travel from one

computer terminal to other terminal they should also follow set of rules and

regulations.

One such set of rules for the networking traffic to follow is IEEE802 standards. Its

developed by IEEE (Institute of Electrical and Electronics Engineers, Inc.) The IEEE

is the world's leading professional association for the advancement of technology.

It's a non- profit organization offering its members immense benefits.

The standards such as IEEE 802 helps industry provide advantages such as,

interoperability, low product cost, and easy to manage standards.

IEEE standards deal with only Local Area Networks (LAN) and Metropolitan Area

Networks (MAN). See in the figure below, to know where exactly the IEEE802

standards are used in a OSI layer.

The IEEE 802 standards are further divided into many parts.

They are,



IEEE 802.1 Bridging (networking) and Network Management

IEEE 802.2 Logical link control (upper part of data link layer)

IEEE 802.3 Ethernet (CSMA/CD)

IEEE 802.4 Token bus (disbanded)

IEEE 802.5 Defines the MAC layer for a Token Ring (inactive)

IEEE 802.6 Metropolitan Area Networks (disbanded)

IEEE 802.7 Broadband LAN using Coaxial Cable (disbanded)

IEEE 802.8 Fiber Optic TAG (disbanded)

IEEE 802.9 Integrated Services LAN (disbanded)

IEEE 802.10 Interoperable LAN Security (disbanded)

IEEE 802.11 Wireless LAN & Mesh (Wi-Fi certification)

IEEE 802.12 demand priority (disbanded)

IEEE 802.13 Not Used

IEEE 802.14 Cable modems (disbanded)

IEEE 802.15 Wireless PAN

IEEE 802.15.1 (Bluetooth certification)

IEEE 802.15.4 (ZigBee certification)

IEEE 802.16 Broadband Wireless Access (WiMAX certification)

IEEE 802.16e (Mobile) Broadband Wireless Access

IEEE 802.17 Resilient packet ring

IEEE 802.18 Radio Regulatory TAG

IEEE 802.19 Coexistence TAG

IEEE 802.20 Mobile Broadband Wireless Access

IEEE 802.21 Media Independent Handoff

IEEE 802.22 Wireless Regional Area Network

Here we discuss most popular and key parts of above list

IEEE 802.3 Ethernet (CSMA/CD)

A method called Carrier Sense Multiple Access with Collision Detection

(CSMA/CD) was used to send data over shared single co-axial cable connected to

all computers on a network. In this method, the computer terminals (also called as

stations) transmits the data over cable whenever the cable is idle, If more than one

station transmit at same time and if they collide, the transmission will be stopped

by such stations. They will wait for some random time and restart transmission.

The concept of sharing single cable or wire between multiple stations was used for

first time in Hawaiian Islands. It was called ALOHA systems; built to allow radio

communication between machines located at different places in Hawaiian Islands.



Later Xerox PARC built a 2.94 mbps CSMA/CD system to connect multiple

personal computers on a single cable. It was named as Ethernet.

Ethernet or IEEE802.3 standards only define MAC (Data link) and Physical layer

of standard OSI model.

Don't confuse TCP/IP with Ethernet. TCP/IP defines Transport and network

layers.

Wiring and cabling standards of 802.3

There are four cabling standards as per 802.3, each one has evolved over the time

for their special advantages.

The four types of cables are,

1. 10Base5

2. 10Base2

3. 10Base-T

4. 10Base-F

The table below compares all four types of cables

Technical

Name

Cable/Wire

type

Max.

Segment/wire

Length

Maximum

number of

Nodes/Segment

Advantages

10Base5 Thick coaxial 500 meters 100 Long cable

length

10Base2 RG58 (thin)

coaxial

185 meters 30 Low cost

10BaseT Twisted pair

(like telephone

wire)

100 meters 1024 Easy to

maintain

10BaseF Fiber-optic 2,000 meters 1024 No noise

interference

The 10 in the technical name refer to data speed of 10Mbits/sec.

"Link Integrity" and "Auto-partition" are part of the 10BaseT specification. This

means that all network equipment claiming compliance with 10BaseT must

support Link Integrity and Auto-partitioning.

10Base5



10 Base5 is also called as ThickNet or thick Ethernet. It uses RG-8 thick coaxial

trunk cable, which looks like orange colored garden hose. The cable is tapered

with taps called vampire taps in which a pin is carefully forced halfway into the

cable's core. The connection can be made to the desired computer network

interface card (NIC) from these vampire taps. ThickNet can travel 500 meters per

segment, and it can have a maximum of 100 taps per segment. Each tap requires a

minimum distance of 2.5 meters before the next tap and has a maximum drop

distance of 50 meters. The cable must be terminated with a 50-ohm terminator

resistor.

Due to its complex and slow nature 10Base5 is no more preferred. The severe

drawback is entire line will fail for any single failure on the trunk. This cable can

be termed as obsolete/outdated technology.

The one plus point of ThickNet is that, once it's up and running, it will continue to

do so until you tell it otherwise. Although it is slow and unwieldy, 10Base5

technology is very reliable.

Here is the figure showing how the cables are connected to Network Interface

Cards inside the computer using 10base5.

10Base2

10Base2 is not very different from 10 Base5. The most notable physical difference

between 10Base2 and 10Base5 is the size of the co-axial cable. 10Base2 is thinner

than the 10Base5 and so is called as ThinNet or thin Ethernet. Another difference

is that 10Base2 is set up in a daisy chain. Daisy chain is a wiring scheme in

which, for example, device A is wired to device B, device B is wired to device C,

device C is wired to device D, et cetera.

10Base2 uses BNC connectors attached to a thin coaxial cable. The maximum



segment length of 10Base2 is 185 meters, and the maximum number of devices per

segment is 30.

10Base is also outdated/obsolete technology. In rare cases it could be deployed as

a backbone for a network.

Here is the figure showing how the cables are connected to Network Interface

Cards inside the computer using 10base5.

10Base-T

10Base-T is the most popular cabling method. Its also called Standard Ethernet,

or twisted pair, 10Base-T works on a star topology connecting all computers to a

hub. It is best used with Category 5 cable (so it can be upgraded to Fast Ethernet)

and can have a maximum of three hubs daisy-chained together.

Since it is simple and cheap to implement it is most opted one. The specifications

of Standard Ethernet include the following:

It uses RJ45 connectors on unshielded twisted-pair (UTP) cable.

The maximum cable length is 100 meters (before a repeater is needed).

The maximum number of devices per segment is 1,024 (although performance will

become quite poor before that number is ever reached).

The 10Base-T standard is best employed within a LAN where cost is a factor-and

speed and distance are not.

Link Integrity is concerned with the condition of the cable between the network

adapter and the hub. If the cable is broken, the hub will automatically disconnect

that port.

Auto partitioning occurs when an Ethernet hub port experiences more than 31



collisions in a row. When this happens, the hub will turn off that port, essentially

isolating the problem.

10Base-F

In 10BaseF the twisted copper wires are replaced by a optical fiber. 10Base-F uses

a higher quality cabling technology, multimode (or single-mode) fiber-optic cable,

to transport data. The particular technology has two subdivisions that must be

addressed: the newer 10Base-FL and 10BaseFOIRL.

Because it is older, the 10BaseFOIRL (Fiber-optic Inter-repeater Link) technology

doesn't have quite the capabilities of the newer 10Base-FL. With 10BaseFOIRL,

you have the following specs:

It's based on IEEE 802.3.

The segment length is 1,000 meters.

There are three sizes of duplex multimode fiber: 50-, 62.5-, or 100-micron. Of

these three, 62.5-micron is the most common.

ST or SMA 905 connectors are used by 10BaseFOIRL.

It must be used in a star configuration.

AUI connectors have to be connected to fiber transceivers.

The much-improved 10Base-FL technology offers a different set of specs:

It's based on the 10Base-F IEEE 802.3 spec.

It's able to interoperate with FOIRL and is designed to replace the FOIRL

specification.

The segment length is 2,000 meters (if exclusively using 10Base-FL).

The maximum number of devices per segment is two; one is the station and the

other is the hub.

The maximum number of repeaters that may be used between devices is two.

NICs with standard AUI ports must use a fiber-optic transceiver.

The benefits of optical fiber are,

No radio or magnetic interference.

Transmissions are safe from electronic bugging,

Cable is extremely lightweight,

10Base-FL fiber-optic technologies are best implemented in long runs where

reliability and security are critical.

Different types of cable topologies:



The four types of cable topologies are, linear, spine, tree, segmented.

Linear: The linear topology is like a single cable running in all portions of

building. The stations are connected to the cable through tapping.

Spine: It looks like our back one spinal cord, where multiple numbers of

horizontal cables are connected to a vertical line through special amplifiers or

repeaters.

Tree: This is most general topology because a network with two paths between

some pairs of stations would suffer from interference between the signals.



Segmented: Since each version of 802.3 has maximum cable length per segment,

to allow larger networks, repeaters can connect multiple cables.

Manchester Encoding: The normal binary logics of one and zero are no more

used to send data from one station to other station. The reason of not using plain

binary signal is they cause ambiguities resulting in false interpretation of sent

data. The major culprit is zero, where even no data is sent the receiver can assume

it as zero.

So to clear out the ambiguity or to ensure proper interpretation of data, a coding

technique called Manchester coding is employed in IEEE802.3 standards.

There are two of Manchester coding, they are simple Manchester coding and

differential Manchester coding.

Summary

Each bit is transmitted in a fixed time (the "period").

A 0 is expressed by a low-to-high transition, a 1 by high-to-low transition

(according to G.E. Thomas' convention -- in the IEEE 802.3 convention, the reverse

is true).



The transitions which signify 0 or 1 occur at the midpoint of a period.

Transitions at the start of a period are overhead and don't signify data.

Manchester code always has a transition at the middle of each bit period and may

(depending on the information to be transmitted) have a transition at the start of

the period also. The direction of the mid-bit transition indicates the data.

Transitions at the period boundaries do not carry information. They exist only to

place the signal in the correct state to allow the mid-bit transition. Although this

allows the signal to be self-clocking, it doubles the bandwidth requirement

compared to NRZ coding schemes (or see also NRZI).

In the Thomas convention, the result is that the first half of a bit period matches

the information bit and the second half is its complement.

If a Manchester encoded signal is inverted in communication, it is transformed

from one convention to the other. This ambiguity can be overcome by using

differential Manchester encoding.

Differential Manchester Encoding Shown in above figure is a variation of basic

Manchester encoding.

A '1' bit is indicated by making the first half of the signal equal to the last half of

the previous bit's signal i.e. no transition at the start of the bit-time. A '0' bit is

indicated by making the first half of the signal opposite to the last half of the

previous bit's signal i.e. a zero bit is indicated by a transition at the beginning of

the bit-time. In the middle of the bit-time there is always a transition, whether from

high to low, or low to high. A reversed scheme is possible, and no advantage is

given by using either scheme.

All 802.3 baseband systems use Manchester encoding due to its simplicity. The

high signal is +0.85 Volts and low signal is -0.85 V giving a DC value of 0 volts.



The 802.3 MAC sub layer protocol

The IEEE802.3 based Ethernet frame consists of preamble of 56 bit-size,

start of the frame delimiter of 8bit size, destination address of 48 bit-size,

sources address of 48 bit-size, type field to identify higher layer protocol of

16 bit-size, data field of variable bit-size, and frame check sequence field

of 32 bit size.

The figure below explains better.

802.3 Ethernet MAC sub layer Protocol Minimum Frame Size

Longest segment = 500 meters

At most 4 repeaters

Maximum LAN length is 2500 m

Maximum round-trip time is 50µsec

10 Mbps implies 100 nsec / bit, 500 bits takes 50 µsec

802.3 uses 512 bits (64 bytes) as minimum frame size

The binary Exponential Backoff Algorithm

Exponential backoff is an algorithm that uses feedback to multiplicatively

decrease the rate of some process, in order to gradually find an acceptable

rate. It is often used in network congestion avoidance to help determine the

correct sending rate. For example, a sender might send a message, set a

timer to wait 0.25 seconds for an acknowledgment, and if none arrives,

retransmit the message and wait 0.5 seconds for an acknowledgment. It

will continue to retry until it receives an acknowledgement and will wait,

1s, 2s, 4s, 8s, etc. each time before retrying.

Time slots are defined to be 51.2µsec during contention period. After i

collisions, backoff random number of intervals between 0 and 2i -1. i is

bounded at 10. After 16 attempts, the sender quits

Basic Intuition used in the algorithm is,

----- Assume that number of contending stations is small until proven



otherwise

----- If i were fixed at 1023, lots of unnecessary waiting

-----If i were fixed at 1, potential for unbounded waiting

The performance of Ethernet (802.3)

Here we evaluate the perfromance of 802.3 under the conditions of full

load and constant load.

Metcalfe and Boggs - ignore binary exponential backoff and assume

constant probability, p, of retransmission in each slot probability that one

station acquires a slot, A, is

where

k = number of stations ready to transmit

p = probability that a station will retransmit

A is maximized when p is 1/k

When p is 1/k, A --> 1/e as k --> infinity

is the probability that the contention window is j slots

Mean number of slots per contention is:

Each slot is bounded by 2t, so the mean window size is bounded by

Assuming optimal p (p = 1/k), A= 1/e and

Let P be the mean transmission time / frame

Let



1. http://www.eeherald.com/section/design-guide/ieee802_p2.html

F = frame length

B = bandwidth

L = cable length

c = speed of light

P = F/B

and

As BL increases, efficiency decreases

Here is the chart showing channel effeciency V/S Number of stations

trying to send

.

Click here for part2[1]

.

http://www.eeherald.com/section/design-guide/ieee802_p2.html



Date post:	23-Apr-2017
Category:	Documents
Upload:	saagar-minocha
View:	214 times
Download:	0 times

Ieee802 Standards

Documents