Date post: | 04-Jun-2018 |
Category: |
Documents |
Upload: | dan-esenther |
View: | 227 times |
Download: | 0 times |
of 14
8/13/2019 IGBT Intelligent Power Modules for AC Motor Drive Up to 2kW-Igbt_ipm_marketing_pres
1/14
IGBT intelligent power modules
Simple and compact solution for AC motor drive up to
8/13/2019 IGBT Intelligent Power Modules for AC Motor Drive Up to 2kW-Igbt_ipm_marketing_pres
2/14
Module approach
More than 30 discrete devices in
a single package
Reduced total
system cost
Easy layout
and design
High quality
and reliability
Improved
efficiency
IGBTs/diodes Gate-driving Ics Passive
components
+ + =
8/13/2019 IGBT Intelligent Power Modules for AC Motor Drive Up to 2kW-Igbt_ipm_marketing_pres
3/14
Simplified design
IGBT intelligent power modules (IPMs) combine application specific IGBT
proprietary control functions, smart protections and extra optional features.
Embedded functions: undervoltage lockout, interlocking function, bootstrap
Optional extra features: smart shutdown, NTC, one to three comparators fo
three op-amps for advanced current sensing (field-oriented control for motor
M
8/13/2019 IGBT Intelligent Power Modules for AC Motor Drive Up to 2kW-Igbt_ipm_marketing_pres
4/14
Key features
Key features
600 V, 3-phase IGBT inverter bridge including gate-driving
ICs and freewheeling diodes
Short-circuit protected IGBTs
Fully-isolated DBC package for enhanced thermal behavio
Smart shutdown function
Comparator for fault protection against overcurrent and sh
Op-amps for advanced current sensing
Integrated bootstrap diode
8/13/2019 IGBT Intelligent Power Modules for AC Motor Drive Up to 2kW-Igbt_ipm_marketing_pres
5/14
Benefits
Benefits
Easy to drive through microcontroller
High efficiency and reliability
Very low Rth
Reduced component count Optimized layout
PCB space reduction (compact design)
Lower failure rate
Easy sensorless field-oriented control (FOC)
8/13/2019 IGBT Intelligent Power Modules for AC Motor Drive Up to 2kW-Igbt_ipm_marketing_pres
6/14
DBC package technology
STs dual in line (DIP) molded packa
a PCB layer for gate drivers and SM
a DBC (direct bonded copper) tech
for better heat dissipation
A vacuum soldering process is used
inclusion (voids) during the solderin
cause potential hot spots. It results
the reliability of STs IPMs due to th
electrical conductivity.
This technology gives STs IPMs lo
values, so ensuring stability in therm
Part number RT
STGIPS10K60A
STGIPS14K60
STGIPL14K60
STGIPS20K60
Cu
8/13/2019 IGBT Intelligent Power Modules for AC Motor Drive Up to 2kW-Igbt_ipm_marketing_pres
7/14
Integrated bootstrap diode
A bootstrap circuitry is required to supply the high-voltage section.
This function is normally accomplished by an external high-voltage fast-
The IPMs integrated gate drivers feature a patented integrated structure
the external diode. This results in component cost saving and easier lay
External bootstrap diode Patented integrated bootstrap stru
8/13/2019 IGBT Intelligent Power Modules for AC Motor Drive Up to 2kW-Igbt_ipm_marketing_pres
8/14
Shutdown function (SD)
The shutdown/open drain is an input/output pin. It can be used both as input
microcontroller for a rapid shutdown, and as an output from the IPM to ackno
a fault condition has been detected by the internal comparator.
When the voltage on pin SD drops below the lower threshold voltage, the IPM
to low level.
The maximum disable time (delay time from SD to the IGBT gates once the f
detected) to put both gates of a leg in low logic state is 200 ns.
Shutdown truth
table
8/13/2019 IGBT Intelligent Power Modules for AC Motor Drive Up to 2kW-Igbt_ipm_marketing_pres
9/14
Shutdown function (SD)
Rsd
Csd
The smart sh
a preferentia
immediately
side due to thinternal delay
fast protectio
the disable ti
dependent ocomponents
The internal be used to im
protection fu
overcurrent o
temperature
8/13/2019 IGBT Intelligent Power Modules for AC Motor Drive Up to 2kW-Igbt_ipm_marketing_pres
10/14
Integrated op-amps
The integrated operational amplifiers are absolutely uncommitted, so a largeamplifier configurations can be implemented by an application designer.
Many types of motor control (including vector control, field-oriented control) phase currents to perform their algorithms. With the IPM, these can be imple
external components and avoiding very complex layouts.
8/13/2019 IGBT Intelligent Power Modules for AC Motor Drive Up to 2kW-Igbt_ipm_marketing_pres
11/14
Interlocking function
The interlock function is an integrated protection that avoids cross-conductio
due to overlapped input signals.
The figure below refers to the STGIPL14K60, but it is analogous for the othe
Deadtime (DT) is the minimum time between turn-off of one IGBT and turn-o
in the same leg. Deadtime has a default value in the datasheet (600 ns for th
but it can also be adjusted by the user via software.
8/13/2019 IGBT Intelligent Power Modules for AC Motor Drive Up to 2kW-Igbt_ipm_marketing_pres
12/14
Undervoltage lockout function (UVLO)
UVL
UVL
If VCC or VBOOT (that supply the high-voltage section) drop below the UVLO
the driver shuts itself down to avoid any high-power-dissipation condition fo
Undervoltage lockout also works at start-up, then VCC
and VBOOT
must be h
UVLO high threshold in order to correctly switch the IPM on.
8/13/2019 IGBT Intelligent Power Modules for AC Motor Drive Up to 2kW-Igbt_ipm_marketing_pres
13/14
Motor control kit
8/13/2019 IGBT Intelligent Power Modules for AC Motor Drive Up to 2kW-Igbt_ipm_marketing_pres
14/14
IPM evaluation boards
STEVAL-IHM025V1
STEVAL-IHM025V1
STEVAL