SYSTEM MODEL #: DATE / / PROJECT 0-10V MANUAL DIMMING Fulham extends a limited warranty only to the original purchaser or to the first user for a period of 5 years from the date of manufacture when properly installed and operated under normal conditions of use. For complete terms and conditions, please reference the Fulham product catalog (www.fulham.com) Due to a program of continuous improvement, Fulham reserves the right to make modifications or variations in design or construction to the equipment described. TYPE 2011-610-1-Rev M E323972 0-10V MANUAL DIMMING SYSTEM ELECTRICAL SPECIFICATION COMMON TO ALL GENERATORS **Surge Protection: Contact Fulham before conducting Hi-Pot test. ***Wiring: Do not modify wire type or length without contacting Fulham for assistance. Reference Remote Mount Options Chart for special factory order systems and wire extensions under Lamp Advance Features. Input Voltage 120-277V EMI/RFI Compliance FCC Part 18-A Voltage Fluctuation Tolerance ±10% Sound Rating Class A Input Frequency 50/60 Hz Type 1 Outdoor Output Frequency <250K Hz Surge Protection** Yes (Reference hi-pot test footnote) THD < 10% Max. Remote Distance*** 7 ft. (84”) (Reference Wiring Footnote) Power Factor > 0.95 Wiring Plug-n-Play Connectors Constant Wattage Output <5% Wire Rating 150°C 600V (Lamp W ire Shielded) Case Temp. < 65°C Electrostatic Discharge (ESD) IEC 61000-4-2:Class 4 Operating Temp. Open Fixture 0°C to 50°C Electrical Fast Transient/Burst(EFT) IEC 61000-4-4: Level 4 Operating Temp. Closed Fixture -20°C to 50°C Surge Immunity IEC 61000-4-5: Class 4 CERTIFICATIONS SYSTEM MODEL NUMBER EXAMPLE This is an original product from Fulham, Co., Inc. 0-10V MANUAL DIMMING SCREW-BASE AND DISC * NOTE: Bare Lamp specifications will vary from fixture test results; LM/W is based on tested Lamp Power. Reference "RELATIVE LUMEN OUTPUT CHART" and contact Fulham for proper Spectrophotocolormeter "Sphere" test procedures. All 0-10V Dimming Generators provide 0-10VDC (Source Type). A Sink Type dimmer is required. At 0VDC the current is 420mA. System Model Number Watts Input current (Amp) 120V - 277V Input Power (W) Rated Initial Lumens (LM) Efficacy (LM/W)* Lumen Maintenance (60Khrs) CRI Color Temp. (Kelvin) Average Lamp Life (Hours) HH-IL-CP40-510M HH-IL-TP40-510M HH-IL-CP55-510M HH-IL-TP55-510M HH-IL-CP70-510M HH-IL-TP70-510M H-I-CDS70-5M HH-IL-CP80-510M HH-IL-TP80-510M HH-IL-CP100-510M HH-IL-TP100-510M H-I-CDS100-5M HH-IL-CP150-510M HH-IL-TP150-510M H-I-CDS150-5M HH-IL-CP200-510M HH-IL-TP200-510M HH-IL-TP200-510M-17 H-I-CDS200-5M HH-IL-CP250-510M HH-IL-TP250-510M H-I-CDS250-5M H-I-CDS300-5M 300 2.63-1.14 315 25500-27000 85-90 H-I-CDS400-5M 400 3.50-1.52 420 34000-36000 85-90 75- 80 70 0.62 - 0.27 74 4900 - 5250 70 - 75 5600 - 6000 85-90 42 158 200 1.75 - 0.76 210 70 - 75 80 - 85 16000 - 17000 80 - 85 100 2800 - 3000 12000 - 12750 250 2.19 - 0.95 263 21250-22500 0.88 - 0.38 105 7500 - 8000 0.48 - 0.21 58 4125 - 4380 70 - 75 80 0.70 - 0.30 84 70%-75% > 80 2700K - 6500K (5K Standard Color) 100,000 70 - 75 40 150 0.35 - 0.15 1.32 - 0.57 55 0-10V MANUAL DIMMING SYSTEM SPECIFICATIONS (PROFILE/DISC) System Model Number Watts Input current (Amp) 120V - 277V Input Power (W) Rated Initial Lumens (LM) Efficacy (LM/W)* Lumen Maintenance (60Khrs) CRI Color Temp. (Kelvin) Average Lamp Life (Hours) H-I-CP40-5MB 40 0.35 - 0.15 42 2800 - 3000 70 - 75 H-I-CP55-5MB 55 0.48 - 0.21 58 4125 - 4380 75 - 80 H-I-CP70-5MB 70 0.62 - 0.27 74 4900 - 5250 70 - 75 H-I-CP80-5MB 80 0.70 - 0.30 84 5600 - 6000 70 - 75 H-I-CP100-5MB 100 0.88 - 0.38 105 7500 - 8000 75- 80 H-I-CP150-5MB 150 1.32 - 0.57 158 12000 - 12750 80 - 85 H-I-CP200-5MB 200 1.75 - 0.76 210 16000 - 17000 80 - 85 70%-75% > 80 2700K - 6500K (5K Standard Color) 100,000 0-10V MANUAL DIMMING SCREW-BASE SYSTEM H = HIGHHORSE H I = INDUCTION LIGHTING SYSTEM I C = CIRCULAR LAMP C SYSTEM WATTS 200 KELVIN TEMP. Specify Kelvin when ordering. 5K is standard stock color. 5 M M = 0-10V MANUAL Reference to dimming. P = PROFILE P BALLAST B B = E39 Mogul Screw Base V REMOTE MOUNT Reference remote mount options chart for code. HH = HIGHHORSE IL = INDUCTION LIGHTING SYSTEM T = TUBULAR LAMP P = PROFILE SYSTEM WATTS KELVIN TEMP. Specify Kelvin when ordering. HH 5K is standard stock color. 10 10V DIMMING Specify the dimming voltage. IL T P 200 5K M M = MANUAL Reference to dimming. BALLAST V REMOTE MOUNT Reference remote mount options chart for code. 0-10V MANUAL DIMMING PROFILE
Transcript
SYSTEM MODEL #: DATE / /
PROJECT
0-10V MANUAL DIMMING
Fulham extends a limited warranty only to the original purchaser or to the first user for a period of 5 years from the date of manufacture when properly installed and operated under normal conditions of use. For complete terms and conditions, please reference the Fulham product catalog (www.fulham.com)Due to a program of continuous improvement, Fulham reserves the right to make modifications or variations in design or constructionto the equipment described.
TYPE
2011-610-1-Rev M
E323972
0-10V MANUAL DIMMING SYSTEM ELECTRICAL SPECIFICATION COMMON TO ALL GENERATORS
**Surge Protection: Contact Fulham before conducting Hi-Pot test.
***Wiring: Do not modify wire type or length without contacting Fulham for assistance. Reference Remote Mount Options Chart for special factory order systems and wire extensions under Lamp Advance Features.
Input V olta ge 120-277V EM I/RFI Com plia nce FCC P art 18-A
V olta ge Fluctua tion Tole ra nce ±10% S ound Ra ting Class A
Input Fre que ncy 50/60 Hz Type 1 Outdoor
Output Fre que ncy < 250K Hz S urge P rote ction** Y es (Reference hi-pot tes t footnote)
THD < 10% M a x . Re m ote Dista nce *** 7 ft. (84”) (Reference W iring Footnote)
P ow e r Fa ctor > 0.95 W iring P lug-n-P lay Connec tors
Consta nt W a tta ge Output < 5% W ire Ra ting 150°C 600V (Lam p W ire S hielded)
Ca se Te m p. < 65°C Ele ctrosta tic Discha rge (ES D) IE C 61000-4-2:Class 4
Ope ra ting Te m p. Ope n Fix ture 0°C to 50°C Ele ctrica l Fa st Tra nsie nt/Burst(EFT) IE C 61000-4-4: Level 4
Ope ra ting Te m p. Close d Fix ture -20°C to 50°C S urge Im m unity IE C 61000-4-5: Class 4
CERTIFICATIONS
SYSTEM MODEL NUMBER EXAMPLE
This is an original product from Fulham, Co., Inc.
0-10V MANUAL DIMMING SCREW-BASE AND DISC
* NOTE: Bare Lamp specifications will vary from fixture test results; LM/W is based on tested Lamp Power.
Reference "RELATIVE LUMEN OUTPUT CHART" and contact Fulham for proper Spectrophotocolormeter "Sphere" test procedures.
All 0-10V Dimming Generators provide 0-10VDC (Source Type). A Sink Type dimmer is required. At 0VDC the current is 420mA.
S yste m M o d e l
N u mb e rW atts
In p u t cu rre n t
(Amp ) 120V - 277V
In p u t P o w e r
(W )
R ate d In itia l
L u me n s (L M )
E fficacy
(L M /W )*
L u me n M ain te n an ce
(60K h rs)C R I
C o lo r T e mp .
(K e lv in )
Av e rag e L amp
L ife (H o u rs)
H H -IL -C P 40-510M
H H -IL -TP 40-510M
H H -IL -C P 55-510M
H H -IL -TP 55-510M
H H -IL -C P 70-510M
H H -IL -TP 70-510M
H -I-C D S 70-5M
H H -IL -C P 80-510M
H H -IL -TP 80-510M
H H -IL -C P 100-510M
H H -IL -TP 100-510M
H -I-C D S 100-5M
H H -IL -C P 150-510M
H H -IL -TP 150-510M
H -I-C D S 150-5M
H H -IL -C P 200-510M
H H -IL -TP 200-510M
H H -IL -TP 200-510M -17
H -I-C D S 200-5M
H H -IL -C P 250-510M
H H -IL -TP 250-510M
H -I-C D S 250-5M
H -I-C D S 300-5M 300 2 .63 -1 .14 315 25500 -27000 85 -90
H -I-C D S 400-5M 400 3 .50 -1 .52 420 34000 -36000 85 -90
75 - 80
70 0 .62 - 0 .27 74 4900 - 5250 70 - 75
5600 - 6000
85 -90
42
158
200 1 .75 - 0 .76 210
70 - 75
80 - 85
16000 - 17000 80 - 85
100
2800 - 3000
12000 - 12750
250 2 .19 - 0 .95 263 21250 -22500
0 .88 - 0 .38 105 7500 - 8000
0 .48 - 0 .21 58 4125 - 4380 70 - 75
80 0 .70 - 0 .30 84
70% -75% > 802700K - 6500K
(5K S tanda rd C o lo r)100 ,000
70 - 7540
150
0 .35 - 0 .15
1 .32 - 0 .57
55
0-10V MANUAL DIMMING SYSTEM SPECIFICATIONS (PROFILE/DISC)
S ys te m M o d e l
N u m b e rW a t ts
In p u t c u r r e n t
(Am p ) 1 2 0 V - 2 7 7 V
In p u t P o w e r
(W )
R a te d In it ia l
L u m e n s (L M )
E f f ic a c y
(L M /W )*
L u m e n M a in te n a n c e
(6 0 K h r s )C R I
C o lo r T e m p .
(K e lv in )
Av e r a g e L a m p
L ife (H o u r s )
H -I-C P 4 0 -5 M B 4 0 0 .3 5 - 0 .1 5 4 2 2 8 0 0 - 3 0 0 0 7 0 - 7 5
H -I-C P 5 5 -5 M B 5 5 0 .4 8 - 0 .2 1 5 8 4 1 2 5 - 4 3 8 0 7 5 - 8 0
H -I-C P 7 0 -5 M B 7 0 0 .6 2 - 0 .2 7 7 4 4 9 0 0 - 5 2 5 0 7 0 - 7 5
H -I-C P 8 0 -5 M B 8 0 0 .7 0 - 0 .3 0 8 4 5 6 0 0 - 6 0 0 0 7 0 - 7 5
H -I-C P 1 0 0 -5 M B 1 0 0 0 .8 8 - 0 .3 8 1 0 5 7 5 0 0 - 8 0 0 0 7 5 - 8 0
H -I-C P 1 5 0 -5 M B 1 5 0 1 .3 2 - 0 .5 7 1 5 8 1 2 0 0 0 - 1 2 7 5 0 8 0 - 8 5
H -I-C P 2 0 0 -5 M B 2 0 0 1 .7 5 - 0 .7 6 2 1 0 1 6 0 0 0 - 1 7 0 0 0 8 0 - 8 5
7 0 % -7 5 % > 8 02 7 0 0 K - 6 5 0 0 K
(5 K S ta n d a rd C o lo r )1 0 0 ,0 0 0
0-10V MANUAL DIMMING SCREW-BASE SYSTEM
H = HIGHHORSE
HI = INDUCTION
LIGHTING SYSTEM
IC = CIRCULAR
LAMP
CSYSTEM WATTS
200KELVIN TEMP.Specify Kelvin when ordering. 5K is standard stock color.
This is an original product from Fulham, Co., Inc.
0-10V MANUAL DIMMING LAMP SYSTEM SPECIFICATIONS
Fulham extends a limited warranty only to the original purchaser or to the first user for a period of 5 years from the date of manufacture when properly installed and operated under normal conditions of use. For complete terms and conditions, please reference the Fulham product catalog (www.fulham.com)Due to a program of continuous improvement, Fulham reserves the right to make modifications or variations in design or constructionto the equipment described.
* LPW is related to the temperature of Amalgam and Kelvin Temperature to maintain >90% output.
Circular/Tubular External Inductor Type
Hybrid Fluorescent All
Primary Ignition Low Frequency Inductor Coil
Induction Lamp Core Mounting Base 100°C - 130°C
Amalgam Lamp Tip Temperature Range 55°C - 125°C
Lamp Coil 160°C - 200°C
Circular/Tubular Convection or Conduction
Color Temperature Fluctuation <10%
LPW Fluctuation <10%
Kelvin Temperature (Standard) 5000K
Lim ited Stock (call Fulham for availability) 3500K, 4000K
Special Factory Order (call Fulham) 2700K, 3000K, 6000K, 6500K
Kelvin Color Temperature Tolerance ±300K
Operating Temperature (Closed Fixture) -40°C Freezer Operation Only (Call Fulham for Ass is tance)
Start Freq. Amplitude End Freq. Amplitude
5Hz 1.5 G 7.07107 Hz 3.5 G
10Hz 3.5 G 30Hz 3.5G
UV (bare lamp-less with lens) 5uw/cm2
Meets International Standard L Level FCC Non-Consumer units Compliant FCC 47-CFR Part 18
EMI
Vibration Tests
UV
Sweep between 5 Hz and 30 Hz at 0.861654 Min/sweep (Linear)
Duration: 100,000 cycles at 100%
Total tes t time: 1:36:30
Care should be taken when mounting ballas t to m inim ize vibration
The HighHorse Induction lamp is des igned to tolerate shock and vibration that would be expected in typical applications
such as post top, bridge, roadway underpass or tunnel lighting. HighHorse Induction lamps have been tested under the
following conditions with no damage:
-Shock - Lamps subjected to three (3) one-half wave shocks of 10 ms duration at 20 g.
-Vibration parameters adapted from ANSI C136.31-2001, American National Standard for Roadway Lighting Equipment -
Luminaire Vibration, Section 5, lum inaire vibration tes t.
Lamp Type
Operating Temperature Range (Thermal Management)
Lamp Operation
Lamp Kelvin Temperature Options
Cold Start and Operation Systems
0-10V DIMMING SPECIFICATIONS
2011-610-2-Rev M
SYSTEM MODEL #: DATE / /
PROJECT
This is an original product from Fulham, Co., Inc.
0-10V MANUAL DIMMING LAMP SYSTEM SPECIFICATIONS (Part II)
TYPE
Fulham extends a limited warranty only to the original purchaser or to the first user for a period of 5 years from the date of manufacture when properly installed and operated under normal conditions of use. For complete terms and conditions, please reference the Fulham product catalog (www.fulham.com)Due to a program of continuous improvement, Fulham reserves the right to make modifications or variations in design or constructionto the equipment described.
Amalgam Type High Quality Solid Pellet
Amalgam Chart
Amalgam Hg.
Lamp Type T40W T55W T70W T100W T150W T200W T250W
Amalgam Type B B B B B C C
Weight/ PC (mg) 40 40 40 40 40 40 40
PCS 2 2 3 3 5 6 9
Total Weight (mg) 80 80 120 120 200 240 360
Content of Hg in % 3.5 3.5 3.5 3.5 3.5 3 3
Pure Hg Weight (mg) 2.8 2.8 4.2 4.2 7 7.2 10.8
Lamp Type C40W C55W C70W C100W C150W C200W C250W C300W
Amalgam Type B B B B B C C C
Weight/ PC (mg) 40 40 40 40 40 40 40 40
PCS 2 2 3 3 5 6 9 10
Total Weight (mg) 80 80 120 120 200 240 360 400
Content of Hg in % 3.5 3.5 3.5 3.5 3.5 3 3 3
Pure Hg Weight (mg) 2.8 2.8 4.2 4.2 7 7.2 10.8 12
Tubular Lamp Circular Lamp
2011-610-3-Rev M
0-10V DIMMING SPECIFICATIONS
Lamp Advanced Features
• Ultra-High Life 100,000hr Rated Lamp Technology
Screw-Base Circular Lamps will operate in any pos ition. Amalgum tube is unique for this type of lamp.
Standard Circular/Tubular (Amalgam Tube-Down Orientation) See page 4.
• Ultra-Low Mercury Content (Encapsulated)
• Wide Range of Wattage Options: 40W/55W/70W/100W/150W/200W/250W/300W/400W
• Full Kelvin Color Range 2700-6500K
• Instant Start
• Flicker Free Operation
• Frequency Power Tuned Wattage to Ballast
• High Quality Phosphor Blends
Lamp Orientation
MADE IN AMERICA
• Pre-Wired Lamp Input Connector
• Universal Heat Sink Mounting
• Aluminum Coil Shield (Non-Corros ive)
• Compatible with Fulham Dimming Generators
• Compatible with Motion and Light Sensor Line Controls
• High CRI (Color Rendering Index)
• High Quality Solid Amalgam Pellet
SYSTEM MODEL #: DATE / /
PROJECT
This is an original product from Fulham, Co., Inc.
LAMP ORIENTATION
Fulham extends a limited warranty only to the original purchaser or to the first user for a period of 5 years from the date of manufacture when properly installed and operated under normal conditions of use. For complete terms and conditions, please reference the Fulham product catalog (www.fulham.com)Due to a program of continuous improvement, Fulham reserves the right to make modifications or variations in design or constructionto the equipment described.
TYPE
Amalgam Tube on the down side orientation for all possible lamp orientations.
2011-610-4-Rev M
SYSTEM MODEL #: DATE / /
PROJECT
This is an original product from Fulham, Co., Inc.
INRUSH / INDUCTANCE
NOTE: ALWAYS CONSULT A LICENSED ELECTRICIAN BEFORE INSTALLING ANY ELECTRICAL DEVICE.
0-10V MANUAL DIMMING SYSTEM INRUSH CURRENT
All types of Inductance (Self/Mutual/Partial/Loop/Loop Mutual) are directly related to the number of magnetic fields around a conducter per amp of current; it requires special equipment to measure inductance. Fulham Retro-fit Engineering Services is equipped to measure and mitigate the effects of Inductance which ultimately can produce failure of the system when not considered in the design of an Induction fixture. All Fulham engineered systems are certified to operate properly relative to Inductance, Thermal, and overall fixture efficacy.
Fulham extends a limited warranty only to the original purchaser or to the first user for a period of 5 years from the date of manufacture when properly installed and operated under normal conditions of use. For complete terms and conditions, please reference the Fulham product catalog (www.fulham.com)Due to a program of continuous improvement, Fulham reserves the right to make modifications or variations in design or constructionto the equipment described.
As with all electronic equipment, Fulham Induction Systems have a peak current shortly after the mains is switched on; while this is a momentary condition it is important to calculate the total load during this peak current demand. It is advised to use C-type MCBs in lighting installations with electronic ballasts. If it is absolutely necessary to connect more than the specified maximum number of fixtures based on peak demand contact a Licensed Electrician and consider a relay in the wiring circuit to limit the number of activated fixtures at one time.
System Model
NumberWatts Voltage
Inrush
Current
Inrush
Period
HH-IL-CP40-510M
HH-IL-TP40-510M
H-I-CP40-5MB
HH-IL-CP55-510M
HH-IL-TP55-510M
H-I-CP55-5MB
HH-IL-CP70-510M
HH-IL-TP70-510M
H-I-CP70-5MB
H-I-CDS70-5M
HH-IL-CP80-510M
HH-IL-TP80-510M
HH-IL-CP100-510M
HH-IL-TP100-510M
H-I-CP100-5MB
H-I-CDS100-5M
HH-IL-CP150-510M
HH-IL-TP150-510M
H-I-CP150-5MB
H-I-CDS150-5M
HH-IL-CP200-510M
HH-IL-TP200-510M
HH-IL-TP200-510M-17
H-I-CP200-5MB
H-I-CDS200-5M
HH-IL-CP250-510M
HH-IL-TP250-510M
H-I-CDS250-5M
H-I-CDS300-5M 300 120V 22.0A 900.0μs
H-I-CDS400-5M 400 120v 25.0A 950.0μs
800.0μs
200
150 120V 14.0A 850.0μs
40 120V 9.0A 600.0μs
120V 16.0A 900.0μs
250 120V 18.0A
100 120V 14.0A 700.0μs
700.0μs14.0A120V70
55 120V 12.0A 700.0μs
80 120V 14.0A 700.0ìs
System Model
NumberWatts Voltage
Inrush
Current
Inrush
Period
HH-IL-CP40-510M
HH-IL-TP40-510M
H-I-CP40-5MB
HH-IL-CP55-510M
HH-IL-TP55-510M
H-I-CP55-5MB
HH-IL-CP70-510M
HH-IL-TP70-510M
H-I-CP70-5MB
H-I-CDS70-5M
H-I-CP80-5MB 80 277V 27.0A 600.0μs
HH-IL-CP100-510M
HH-IL-TP100-510M
H-I-CP100-5MB
H-I-CDS100-5M
HH-IL-CP150-510M
HH-IL-TP150-510M
H-I-CP150-5MB
H-I-CDS150-5M
HH-IL-CP200-510M
HH-IL-TP200-510M
HH-IL-TP200-510M-17
H-I-CP200-5MB
H-I-CDS200-5M
HH-IL-CP250-510M
HH-IL-TP250-510M
H-I-CDS250-5M
H-I-CDS300-5M 300 277V 36.0A 830.0μs
H-I-CDS400-5M 400 277V 39.0A 830.0μs
55 277V 18.0A 500.0μs
27.0A 600.0μs
500.0μs40 277V 18.0A
250 277V 35.0A 800.0μs
32.0A 700.0μs150 277V
200 277V 34.0A 800.0μs
70 277V 27.0A 600.0μs
100 277V
2011-610-5-Rev M
SYSTEM MODEL #: DATE / /
PROJECT
This is an original product from Fulham, Co., Inc.
REMOTE MOUNT
LENGTH
MALE CONNECTOR TO LAMPFEMALE CONNECTOR TO BALLAST
WIRE SPECIFICATIONS:150°600V18AWG
WIRE SHIELD
ASSEMBLY VIEW SCALE 1:5
POWER SOURCE:120V - 277V
NOTE: Product is shipped as shown SCALE 1:3
*HHILPE00007 is ONLY for Fulham Tubular and Circular Induction Systems
Fulham extends a limited warranty only to the original purchaser or to the first user for a period of 5 years from the date of manufacture when properly installed and operated under normal conditions of use. For complete terms and conditions, please reference the Fulham product catalog (www.fulham.com)Due to a program of continuous improvement, Fulham reserves the right to make modifications or variations in design or constructionto the equipment described.
Contact Fulham for assistance in engineering your custom wire options.
Factory Special Order Only; subject to minumum quantity and lead times at time of order.Contact Fulham for requirements prior to order. Orders are non-cancellable.Remote mount options are not available for the disc dimming generators.
Lamp Advanced Features
SYSTEM MODEL #: DATE / /
PROJECT
This is an original product from Fulham, Co., Inc.
Rated Lumen Maintenance Chart
Rated Lumen Maintenance is largely determined by operating temperature of the lamp and quality of lamp design; Fulham HighHorse induction systems are designed and manufactured with high quality tri-phosphors and solid amalgam to optimize the performance and rated life of the lamp. The above chart is intended to represent an average rated lumen output stated as a percentage of the initial lumen output over the rated life of the lamp. Operating the lamp within the temperatures specifcation will typically result in not less than 70% lumen output at 60Khrs.
HighHorse induction systems operate within a wide range of ambient; the chart is an example of a 100W induction system operated at extreme cold temperature. It is recommended if the system requires a cold start at -30°C that a thermal blanket be installed at the factory on the amalgam tip; this will ensure a consistent start and rapid stabilization of the lamp and lumen output.
Note: Closed fixture example, actual performance varies with fixture types.
LUMEN MAINTENANCE
NOTE: Purpose of Lumen Maintenance Chart is strictly to show relation of the three variables over time.
System Rated Life varies with operating temperature and application. Fulham HighHorse induction generators are designed with high quality long lasting components and when operated at the rated Tc 65ºC expected life is 60Khrs with failure rate of 15% to 20%. Operating temperatures less than the rated Tc 65ºC can typically improve life
OPERATING HOURS
SU
RV
IVA
L %
90
80
70
5020,000 40,000 60,000 80,000 100,000
60
0
100
expectancy and reduce failure rate.
Relative Light OutputSystem Power
Rela
tive L
um
en O
utp
ut
Amalgam Temperature (C°)
100W ballast
110
100
90
80
70
60
50
40
30
20
10
0
220
200
180
160
140
120
100
80
60
40
20
040 50 60 70 80 90 100 110 120 130 140
Relative Lumen Output Chart
Lumen output is directly related t System Power and Amalgam Temperature;properly designed systems result in a stable lamp condition and maximum lightoutput. All Fulham Engineered HighHorse Induction systems operate with less than a15% vatiation over a wide range of Amalgam operating temperature (60ºC - 125ºC).Fulham Retro-fit systems are engineered for a maximum light output and improved lifeexpectancy.
TYPE
Fulham extends a limited warranty only to the original purchaser or to the first user for a period of 5 years from the date of manufacture when properly installed and operated under normal conditions of use. For complete terms and conditions, please reference the Fulham product catalog (www.fulham.com)Due to a program of continuous improvement, Fulham reserves the right to make modifications or variations in design or constructionto the equipment described. 2011-610-7-Rev M
SYSTEM MODEL #: DATE / /
PROJECT
This is an original product from Fulham, Co., Inc.
TEMPERATURE TEST POINTS
NOTE: TEMPERATURE MEASUREMENTS ARE RECOMMENDED TO BE AT THE RATED TEMPERATURE FOR BEST PERFORMANCE AND LIFE EXPECTANCY. LAMP AND GENERATOR TEMPERATURES MAY NOT EXCEED THE MAXIMUM OPERATING AMBIENT TEMPERATURE WHEN INSTALLED IN A FIXTURE.
8
7
6
CIRCULAR LAMP
1
2
3
PROFILE BALLAST
CONTACT FULHAM FOR APPROVED TEMPERATURE TEST PROCEDURE.
0-10V MANUAL DIMMING SYSTEM TEMPERATURE CHART
TYPE
Fulham extends a limited warranty only to the original purchaser or to the first user for a period of 5 years from the date of manufacture when properly installed and operated under normal conditions of use. For complete terms and conditions, please reference the Fulham product catalog (www.fulham.com)Due to a program of continuous improvement, Fulham reserves the right to make modifications or variations in design or constructionto the equipment described.
PLEASE NOTE: Induction lamps are fragile and require care when handling; DO NOT allow the glass to come in contact with metal objects. The amalgam glass can be easily broken.
Note: Test points 2 and 3 are on the side of the ballast; location is not precise.
TUBULAR LAMP
8
7
6
1013
12
TEST POINT TEMPERATURE TEST POINTS: RATED TEMPERATURE MAX TEMPERATURE
12 LAMP TUBE ON INSIDE CENTER < 140ºC (284ºF) 180ºC (356ºF)
13 WIRE CONNECTOR < 105ºC (221ºF) 105ºC (221ºF)
8 7
6
12
10
CIRCULAR SCREW-BASE LAMP
2011-610-8-Rev M
1
23
DISC BALLAST
SYSTEM MODEL #: DATE / /
PROJECT
This is an original product from Fulham, Co., Inc.
DIMENSIONS - TUBULAR
Contact Fulham for detailed drawings.* Subject to change. Contact Fulham for specific wire lengths.
TYPE
Fulham extends a limited warranty only to the original purchaser or to the first user for a period of 5 years from the date of manufacture when properly installed and operated under normal conditions of use. For complete terms and conditions, please reference the Fulham product catalog (www.fulham.com)Due to a program of continuous improvement, Fulham reserves the right to make modifications or variations in design or constructionto the equipment described.
HH-IL-T55W5K 7.96 4.42 2.78 و � 16 ت
HH-IL-T80W5K EBĎĈ DBĎD 3.04 و � 15 ت
ĈĈBDĐ
ĈDBČČ
ĈĐBĆĐ
ČĈBDĆ
DBĎD
ĐBČÐ
DBĎD
HH-IL-T250W5K
Model No.
HH-IL-T40W5K
HH-IL-T70W5K
HH-IL-T100W5K
HH-IL-T150W5K
HH-IL-T200W5K-17
HH-IL-T200W5K
3.02
Input Wire L (in)
و � 15 ت
و � 15 ت
و � 15 ت
و � 15 ت
و � 15 ت
و � 15 ت
و � 15 ت
H (in)
2.78
W (in)
4.42
DBĎD
DBĎD
3.04
3.04
3.04
3.04
3.04
Tubular Lamp
L (in)
7.96
EBĎĈ
ČĊBĆĆ ĐBČÐ
.03"H
40W - 55W
.10"L
W .15"
H ± .10”
W ± .10”
L ± .10”
70W - 250W
2011-610-9-Rev M
SYSTEM MODEL #: DATE / /
PROJECT
This is an original product from Fulham, Co., Inc.
DIMENSIONS - CIRCULAR
TYPE
Fulham extends a limited warranty only to the original purchaser or to the first user for a period of 5 years from the date of manufacture when properly installed and operated under normal conditions of use. For complete terms and conditions, please reference the Fulham product catalog (www.fulham.com)Due to a program of continuous improvement, Fulham reserves the right to make modifications or variations in design or constructionto the equipment described.
This is an original product from Fulham, Co., Inc.
DIMENSIONS - BALLASTS
TYPE
Fulham extends a limited warranty only to the original purchaser or to the first user for a period of 5 years from the date of manufacture when properly installed and operated under normal conditions of use. For complete terms and conditions, please reference the Fulham product catalog (www.fulham.com)Due to a program of continuous improvement, Fulham reserves the right to make modifications or variations in design or constructionto the equipment described.
Contact Fulham for detailed drawings.* Subject to change. Contact Fulham for specific wire lengths.
HH-IB-UNV-TP40M SMALL "40" 5.98 3.66 1.63 10± 1" 10± 1"
10± 1" 10± 1"HH-IB-UNV-TCP250M LARGE 10.00 4.75 2.07
10± 1" 10± 1"
HH-IB-UNV-TCP200M STANDARD 8.46 4.75 2.07 10± 1" 10± 1"
HH-IB-UNV-TCP150M STANDARD 8.46 4.75 2.07
10± 1" 10± 1"HH-IB-UNV-TCP100M MEDIUM 7.06 4.12 1.91
10± 1" 10± 1"HH-IB-UNV-TCP70M MEDIUM 7.06 4.12 1.91
HH-IB-UNV-TCP80M MEDIUM 7.06 4.12 1.91 10± 1" 10± 1"
10± 1" 10± 1"HH-IB-UNV-CP40M SMALL "40" 5.98 3.66 1.63
HH-IB-UNV-CP55M SMALL "40" 5.98 3.66 1.63 10± 1" 10± 1"
HH-IB-UNV-TP55M SMALL "40" 5.98
Profile Ballast
Model No. Size L W H Input Wire L (in) Output Wire L (in)*
3.66 1.63 10± 1" 10± 1"
W± .03”
L± .03”
H± .03”
Profile Aluminum Ballast (Black)
2011-610-11-Rev M
X .05"
H .10"
Disc Ballast (White)
Model No. SIZE H (in) ØX (in) Input wire L (in) Output wire L (in)
HH-IB-UNV-CD70M SMALL 9.52 8.04 12.2± 1" 12.2± 1"
HH-IB-UNV-CD100M SMALL 9.52 8.04 12.2± 1" 12.2± 1"
HH-IB-UNV-CD150M MEDIUM 10.30 9.60 12.2± 1" 12.2± 1"
HH-IB-UNV-CD200M MEDIUM 10.30 9.60 12.2± 1" 12.2± 1"
HH-IB-UNV-CD250M STANDARD 10.94 11.04 12.2± 1" 12.2± 1"
HH-IB-UNV-CD300M STANDARD 10.94 11.04 12.2± 1" 12.2± 1"
HH-IB-UNV-CD400M STANDARD 10.94 11.04 12.2± 1" 12.2± 1"
Disc Ballast
SYSTEM MODEL #: DATE / /
PROJECT
WIRING DIAGRAM
TYPE
Fulham extends a limited warranty only to the original purchaser or to the first user for a period of 5 years from the date of manufacture when properly installed and operated under normal conditions of use. For complete terms and conditions, please reference the Fulham product catalog (www.fulham.com)Due to a program of continuous improvement, Fulham reserves the right to make modifications or variations in design or constructionto the equipment described. 2011-610-12-Rev M
Screw-Base Wiring
0-10V Dimming Wiring
WHT
BLK
LAMP
INPUT120 - 277V
BALLAST MUSTBE GROUNDED
BROWN
RED
GRN
GRAY
VIOLET0 ~ 10V
DIMMER
COM
INDUCTION
GENERATORON/OFFSWITCH
Note: See below for Screw-Base System Wiring Diagram.
MINIMUM WIRE REQUIREMENTS:90° C600V18AWGStranded wire is recommended.
MOGUL BASE:Type E39
WIRE SPECIFICATIONS:150° C600V18AWG
POWER SOURCE120V - 277V
Use wire nuts to attach ends.No polarity.
***Wiring: Do not modify wire type or length without contacting Fulham for assistance. Reference Remote Mount Options Chart for special factory order systems and wire extensions under Lamp Advance Features.
DimmingGenerator
GR
ND
DIM
-D
IM+
LO
AD
LIN
EN
EU
T
GROUND
GRAY
VIOLET
LOAD
NEUTRAL
LIN
E
NE
UT
RA
L
BR
OW
N
RE
D
SYSTEM MODEL #: DATE / /
PROJECT
0-10V Dimming
TYPE
Fulham extends a limited warranty only to the original purchaser or to the first user for a period of 5 years from the date of manufacture when properly installed and operated under normal conditions of use. For complete terms and conditions, please reference the Fulham product catalog (www.fulham.com)Due to a program of continuous improvement, Fulham reserves the right to make modifications or variations in design or constructionto the equipment described. 2011-610-13-Rev M
The Induction lighting system can be controlled with the traditional analogue dimming technology of 0-10VDC. The system is a Step Dimming done in 64 steps. All 0-10V Dimming
0-10V DIMMING FEATURES
0-10V SPECIFICATION
Generators provide 0-10VDC (Source Type). A Sink Type dimmer is required. At 0VDC the current is 420mA
The 0-10V dimming interface is electrically isolated for safety and reliability The dimmable Induction generator can work as a regular generator to _____drive the lamp at full range when the 0-10V interface is not connected. The output wattage is about 50% at 0-3VDC. The output wattage is dimmed from 100% to 50% at the 9-3VDC. The output wattage is 100% at 9-10VDC. The output wattage is at the 100% range when the system is power ON. If _____the system is set on a dim level then it will dim within 30 seconds. Shorting the two dimming wires (Violet and Gray) sets the system to the _____lowest dim level of 50%, acting as a bi-level dimming system. Violet (+) Gray (-)
