ILLUSTRATED PARTS LIST - Universal Sewing › images2 › parts_lists › all › ...ILLUSTRATED...

I LLUSTRATED PARTS L IST

MANUAL NO. PT9511

S T Y L E S

Three Needle, Wide Gauge, Plain FeedMachines with Top Cover Thread

FS113L100MBV096FS113L112MBV096

2

Manual No. PT9511 Illustrated Parts List for FS100 Series Machines

Third Edition Copyright 1997By

Union Special Corporation Rights Reserved In All CountriesPrinted in U.S.A. May 1997

PREFACE

This parts manual has been prepared to assist you in locating individual parts or assemblies on FS100 Series machines.It can be used in conjunction with Union Special Adjusting Manual IN9302.

It is the desire of Union Special that each machine run at its optimum performance. Parts listed in this manual are designedspecifically for your machine and are manufactured with the utmost precision to assure long lasting service.

This manual has been comprised on the basis of available information. Changes in design and/or improvements mayincorporate a slight modification of configuration in illustrations or part numbers.

On the following pages are illustrations and terminology used in describing the parts used on FS100 Series machines.

3

SAFETY RULES

The sewing machines described in this instruction manual are prohibited from being put into service until it has beenascertained that the sewing units, in which these sewing machines will be built-in have conformed with the EC CouncilDirectives (89/392/EEC, Annex II B).

1. Before putting the machines described in this manual into service, carefully read the instructions. The starting of eachmachine is only permitted after taking notice of the instructions and by qualified operators.

IMPORTANT! Before putting the machine into service, also read the safety rules and instruction from the motor supplier.

2. Observe the national safety rules valid for your country.

3. Each machine is only allowed to be used as foreseen. The foreseen use of the particular machine is described in paragraph“STYLES OF MACHINES” of this instruction manual. Another use, going beyond the description, is not as foreseen.

4. All safety devices must be in position when the machine is ready for work or in operation. Operation of the machine withoutthe appertaining safety devices is prohibited.

5. Wear safety glasses.

6. In case of machine conversions and changes all valid safety rules must be considered. Conversions and changes are madeat your own risk.

7. The warning hints in the instructions are marked with one of these two symbols:

8. For the following the machine has to be disconnected from the power supply by turning off the main switch or by pullingout the main plug:

8.1 For threading needle(s), looper, spreader etc.

8.2 For replacing sewing parts such as needle, presser foot, throat plate, looper, spreader, feed dog, needle guard,folder, fabric guide etc.

8.3 When leaving the workplace and when the workplace is unattended.

8.4 For maintenance work.

8.5 When using clutch motors without actuation lock, wait until the motor is stopped totally.

9. Maintenance, repair and conversion work (see item 8) must be done only by trained technicians or special skilled personnelunder consideration of the instructions.

10. Any work on the electrical equipment must be done by an electrician or under direction and supervision of special skilledpersonnel.

11. Work on parts and equipment under electrical tension is not permitted. Permissible exceptions are described in theapplicable sections of standard sheet DIN VDE 0105.

12. Before doing maintenance and repair work on the pneumatic equipment, the machine has to be disconnected from thecompressed air supply. In case of existing residual air pressure after disconnecting from compressed air supply (e.g.pneumatic equipment with air tank), the pressure has to be removed by bleeding.

* Exceptions are only allowed for adjusting work and function checks done by special skilled personnel.

4

CAUTION AREAS

WEAR SAFETYGLASSES, DO NOT

TAMPER WITHSAFETY SHIELD.

USE WITHOUTSHIELD MAY

CAUSE INJURY.

CAUTION

KEEP NEEDLE

BAR GUARD

IN PLACE

CAUTION

CAUTION

KEEPBELT GUARD

IN PLACE

CAUTIONDO NOT OPERATE

MACHINE WITHOUT THISBELT GUARD IN PLACE

KEEP COVERCLOSED DURING

OPERATION

CAUTION

5

THREADING

A Right Needle ThreadB Middle Needle ThreadC Left Needle ThreadD Spreader ThreadE Rear/Right Looper ThreadF Middle Looper ThreadG Front/Left Looper Thread

1 Spreader Thread Take-Up & Nipper Area2 Needle Head & Needle Thread Nipper Area3 Sewing Area4 Looper, Looper Thread Take-up & Nipper Area5 Needle Lever Thread Eyelet Area

6

CONTENTS•PREFACE................................................................................................................................................................ 2•SAFETY RULES ....................................................................................................................................................... 3•CAUTION AREAS..................................................................................................................................................... 4•THREADING ............................................................................................................................................................ 5•IDENTIFICATION OF MACHINES .............................................................................................................................. 7•MACHINE STYLES ................................................................................................................................................... 7•NEEDLES ............................................................................................................................................................... 7•TERMS ................................................................................................................................................................... 7•ILLUSTRATIONS...................................................................................................................................................... 8•IDENTIFYING PARTS ............................................................................................................................................... 8EXPLODED VIEWS•MISCELLANEOUS COVERS, GUARDS, THREAD GUIDES & CAST-OFF PLATE......................................................... 11•MISCELLANEOUS COVERS, GUARDS, THREAD GUIDES & CAST-OFF PLATE (CONT.) ........................................... 13•LUBRICATION SYSTEM & BUSHINGS..................................................................................................................... 15•CRANKSHAFT, NEEDLE LEVER, NEEDLE BAR & LOOPER DRIVE MAECHANISM ................................................... 17•CRANKSHAFT, NEEDLE LEVER, NEEDLE BAR & LOOPER DRIVE MECHANISM (CONT.) ........................................ 19•SPREADER MECHANISM DRIVE ................................................................................................................... 21•LOOPER ROCKER & CONNECTING ROD ............................................................................................................... 23•FEED MECHANISM, MAIN SHAFT & TAKE-UP ........................................................................................................ 25•FEED MECHANISM, MAIN SHAFT & TAKE-UP (CONT.) ........................................................................................... 27•PRESSER FOOT LIFTER LEVER ............................................................................................................................. 29•THREAD TENSION ASSEMBLY .............................................................................................................................. 31•COVERS & MISCELLANEOUS PARTS .................................................................................................................... 33•PRESSER FOOT, THROAT PLATE & FEED DOG .................................................................................................... 35•CHAIN CUTTER ASSEMBLY FOR STYLE:

FS113L112MBV096 ............................................................................................................................................. 37•SHUTTLE VALVE ASSEMBLY FOR STYLE:

FS113L112MBV096 ............................................................................................................................................. 39•MUFFLER/ CHAIN RECOVERY SYSTEM FOR STYLE:

FS113L112MBV096 ............................................................................................................................................. 41•TREADLE OPERATED AIR VALVE ASSEMBLY FOR STYLE:

FS113L112MBV096 ............................................................................................................................................. 43•FILTER, REGULATOR, LUBRICATOR, GAUGE ASSEMBLY FOR STYLE:

FS113L112MBV096 ............................................................................................................................................. 45•AIR CIRCUIT DIAGRAM FOR STYLE:

FS113L112MBV096 ............................................................................................................................................. 46•NOTES ................................................................................................................................................................. 47•ACCESSORIES ...................................................................................................................................................... 49•NUMERICAL INDEX OF PARTS .............................................................................................................................. 50•NUMERICAL INDEX OF PARTS .............................................................................................................................. 51•NOTES ................................................................................................................................................................. 52•NOTES ................................................................................................................................................................. 53

7

IDENTIFICATION OF MACHINES

Each Union Special machine carries a style number, which on this class machine is stamped in the style plate affixedto the right front of the machine.

The serial number is stamped in the casting at the right rear base of machine.

MACHINE STYLES

Advanced series, heavy duty flat bed machine. Three needles, three loopers, one spreader, one auxiliary spreader,plain feed, enclosed automatic lubrication system. Maximum work space to right of needle bar 81/4" (210mm).

FS113L100MBV LAP-SEAMER: Three needle, top cover thread, plain feed machine - Typical application -For pocket facing applications on medium to heavy weight denim. Seam specification408LSbj-1 (Mod.). Standard Gauge Number 096 [3/8", 9.6 mm]. Maximum recommendedspeed depending on application is 4500 R.P.M. Recommended needle 128 GS, size125/049.

FS113L112MBV Same as style FS113L100MBV096 except fitted with a flat action (mounted on cloth plate),compressed air operated chain cutter with venturi suction and chain disposal.

NEEDLES

Each needle has both a type and size number. The type number denotes the kind of shank, point, length, groove,finish and other details. The size number, stamped on the needle shank, denotes the largest diameter of the blademeasured between the shank and the eye. Collectively, the type number and size number represent the completesymbol which is given on the label of all needles packed and sold by Union Special.

TYPE DESCRIPTION

128 GS Short, double groove, struck groove, ball eye, spotted, undersize eye and grooves 27% of size ofneedle, chromium plated - Sizes Available 090/036,100/040,110/044, 125/049, 140/054.

When changing the needle, make sure it is fully inserted in the needle head before the screw is tightened.

To have needles promptly and accurately filled, an empty package, a needle sample, or the type and size numbershould be forwarded. Use the description on the label. A complete order should read as follows: "100 needles,type 121 GBS, size 125/049".

TERMS

Prices are net cash and subject to change without notice. All shipments are forwarded F.O.B. shipping point. Acharge is made to cover postage and insurance.

ILLUSTRATIONS

This manual has been arranged to simplify ordering repair parts. Exploded views of various sections of themechanism are shown so that the parts may be seen in their actual position in the machine. On the page oppositethe illustration will be found a listing of the parts with their part numbers, description and the number of piecesrequired in the particular view being shown.

Numbers in the first column are reference numbers only, and merely indicate the position of the part in theillustration. The reference number should never be used in ordering parts. Always use the part number listed inthe second column.

Component parts of sub-assemblies which can be furnished for repairs are indicated by indenting their descriptionsunder the description of the main sub-assembly. As an example refer to the following text.

9. 29126EC Upper Looper Drive Shaft Assembly ........................................ 110. 22503F Screw ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111. 39543E Cam Follower Locking Clamp ............................................. 1

When a part is common to all machines covered in this manual, no specific usage will be mentioned in the description.However, when the parts for the various machines are not the same, the specific usage will be mentioned in thedescription and, if necessary, the difference will be shown in the illustration.

A numerical index of all the parts shown in this manual is located at the back. This will facilitate locating theillustration and description when only a part number is known.

IDENTIFYING PARTS

Where the construction permits, each part is stamped with its part number. On some of the smaller parts and onthose where construction does not permit, an identification letter is stamped in, to distinguish the part from similarones.

PLEASE NOTE: Part numbers represent the same part, regardless of which manual they appear in. On all ordersplease include part number, name and style of machine for which the part was ordered.

* For optimum performance, use only genuine Union Special replacement parts.

8

EXPLODED VIEWS ...

1 0

17

13

80

7

77

17576

2

5 43

6

89

10 1112

14

15

16

17

18

19

79

2322

2120

2021

4645

47

48

4850

5253

78

49

24

252624

37

29

32

30

31

28

27 3433

36

35

67

66

65

81

82

83

84

8586

89

88

38

39

5758

596061

4041

4243

44

72

7473

71

55

56

54

71

70

6968

70

51

90

6364

87

62

1 1

Part No. DescriptionAmt.Req.

Ref.No.

MISCELLANEOUS COVERS, GUARDS, THREAD GUIDES & CAST-OFF PLATE

56382Y56382AB56382AV56382J2282956382AA228482252456382AU2254856382D56382AX660-100222541C57782M56382AY9056382AC22539S8055722839C21375CE2282998A158A56391B51457B52804A2851959D51959K51959B5149251959J22569C69H52958G22585C57858C57892H57892C580665F57892J5784422848205175853922889H57882J22585C

1 .2 .3 .4 .5 .6 .7 .8 .9 .

10.11.12.13.14.15.16.17.18.19.20.21.22.23.24.25.26.27.28.29.30.31.32.33.34.35.36.37.38.39.40.41.42.43.44.45.46.47.48.49.50.51.

Block, for oil drip plate ......................................................................Oil Drip Plate ....................................................................................Gasket, for looper drive shaft cover .....................................................Cover, for looper drive shaft ................................................................Screw, for looper drive shaft cover ........................................................Oil Reservoir Cover, back .....................................................................Screw, for oil reservoir cover, back .....................................................Screw, for oil drip plate .....................................................................Gasket, for oil reservoir cover, back ......................................................Screw, for crank chamber cover, lower ..................................................Crank Chamber Cover, lower ...............................................................Gasket, for crank chamber cover, lower .................................................Plug, for crank chamber cover, upper ....................................................Screw, for crank chamber cover, upper ..................................................Crank Chamber Cover, upper ...............................................................Gasket, for crank chamber cover, upper ..................................................Screw, for bearing oiler assembly ..........................................................Bearing Oiler Assembly .......................................................................Plug Screw, for bed ............................................................................Washer, for tension assembly (see page 31) ............................................Screw, for tension assembly (see page 31) .............................................Belt Guard .......................................................................................Screw, for belt guard ..........................................................................Screw, for looper guard thread eyelet ....................................................Looper Thread Eyelet ..........................................................................Looper Thread Guard ..........................................................................................Cast-Off Plate .....................................................................................................Hold Down Plate, for looper thread ......................................................................Screw, for hold down plate ..................................................................................Tension Nut ......................................................................................................Tension Spring ................................................................................Tension Disc ..................................................................................Tension Post ..................................................................................Looper Thread Guide .........................................................................Screw, for support plate ...................................................................Washer, for support plate screw .........................................................Eyelet, for looper thread ...................................................................Screw, for eyelet ............................................................................Eyelet, looper thread ......................................................................Nut, for spreader thread post ..............................................................Spreader Tension Spring ...................................................................Disc, for tension post .........................................................................Spreader Tension Post .....................................................................Spreader Thread Guide .....................................................................Screw, for thread eyelets ................................................................Washer, for thread eyelets ................................................................Eyelet, spreader thread ...................................................................Eyelet, needle thread ....................................................................Adapter Screw .................................................................................Guard, for needle lever eyelet .............................................................Screw, for needle lever eyelet ............................................................

111121921411141121122123111121121122111112111112111

52. thru 88. See following page.

1 2

17

13

80

7

77

17576

2

5 43

6

89

10 1112

14

15

16

17

18

19

79

2322

2120

2021

4645

47

48

4850

5253

78

49

24

252624

37

29

32

30

31

28

27 3433

36

35

67

66

65

81

82

83

84

8586

89

88

38

39

5758

596061

4041

4243

44

72

7473

71

55

56

54

71

70

6968

70

51

90

6364

87

62

1 3


Ref.No.

57858B9557844C3475857858A43296A2279757WB15438C57WD34844D287757845E22585A22513B57882K22539AB22541C22851D57882P22564B34831C22539AA22585A564703379522894E660-61799682XF1407799683CN99682XC29597856525F99696A22758E2276656525E

111111111111111111221421111211111111121

Eyelet, spreader thread ...............................................................................Set Screw .......................................................................................Eyelet Mounting Plate .........................................................................Needle Thread Guide ..........................................................................Thread Guide Spring ..........................................................................Base Nipper Spring ...........................................................................Screw .... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Nipper Tension Plate ..........................................................................Nipper Spring ..................................................................................Screw, for nipper spring ....................................................................Spreader Thread Guide Mounting Plate ...................................................

Screw .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Screw .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Spreader Thread Guide ...................................................................Screw, for spreader thread mounting plate ..........................................Screw , for spreader thread mounting plate ...........................................Head Cover .....................................................................................

Plug Screw, for head cover .....................................................................Screw, for head cover ...................................................................Screw, for head cover .......................................................................Gasket, for head cover ......................................................................Screw, for guide plate ......................................................................Guide Plate ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Plug Screw, for bed ..........................................................................Screw, for eyelet guard .................................................................Needle Thread Take-Up ..................................................................Guard, for needle thread eyelet ..........................................................Screw, for needle lever stud ...........................................................Gasket, for needle lever eyelet ........................................................Needle Break Guard Assembly ..........................................................

Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Mounting Plate .......................................................................Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Spring Washer .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Spacer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Shield .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Shoulder Screw ........................................................................Screw ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Sewing Guard ..................................................................................

52.53.54.55.56.57.58.59.60.61.62.63.64.65.66.67.68.69.70.71.72.73.74.75.76.77.78.79.80.81.82.83.84.85.86.87.88.89.90.

MISCELLANEUOS COVERS, GUARDS, THREAD GUIDES & CAST-OFF PLATE (CONT.)

1. thru 51. See preceding page.

1 4

3 9

3 7

6

2 3

14

23

54 1

5

7

8

79

78

97

1 1 1 4

1 3 1 2

1 5

1 62 7

2 8

2 93 03 1

1 0

4 0

3 83 6

3 5

3 33 4

3 2

2 3

2 4 25

22

2 6

1 9

1 8

1 71 9

2 0

2 1

1 5


Ref.No.

LUBRICATION SYSTEM & BUSHINGS

11112142211311111221112111111111111111111

1 .2 .3 .4 .5 .6 .7 .8 .9 .

10.11.12.13.14.15.16.17.18.19.20.21.22.23.24.25.26.27.28.29.30.31.32.33.34.35.36.37.38.39.40.41.

59493A660-230258A666-21457849CL2156390H56390J660-66552883R21657X22569B57890B56390E22539R51-902BLK999-216K52942AB50-895BLK56393P666-2595639057836B57842B5619035897BV56393Q56390G5789357893A666-214660-73951257AA57847B5785457893C6-67-12556393W22585A660-40651154E

Base Oil Pump Assembly ......................................................................Gasket .......................................................................................Nut ...........................................................................................Felt Intake ..................................................................................

Bushing, for spreader rocker shaft .........................................................Oil Wick ...........................................................................................Thrust Washer ..................................................................................Pilot Ring .........................................................................................Needle Thrust Bearing ........................................................................Bushing, for presser foot lifter ..............................................................Release Bushing ................................................................................Screw, for crankshaft bushing housing ...................................................Crankshaft Bushing Housing .............................................................Gasket, housing ................................................................................Oil Drain Plug ....... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Oil Sight Gauge ...............................................................................Plug, for bed ..................................................................................Bushing, for looper drive lever shaft, front .............................................Bushing, for looper rocker shaft ............................................................Felt, base, front ................................................................................Felt ...............................................................................................Main Shaft Bushing, left ....................................................................Bushing, for feed rocker shaft ..............................................................Bushing, for looper drive shaft, rear ......................................................Main Shaft Bushing, middle ..................................................................Filter, for main shaft bushing ...............................................................Felt, base, rear ................................................................................Main Shaft Bushing, right ....................................................................Oil Pump Assembly, head ...................................................................

Oil Tube ....................................................................................Felt Intake .................................................................................

Oil Seal ..........................................................................................Presser Bar Bushing ...........................................................................Spreader Bushing .............................................................................Needle Bar Bushing, lower ..................................................................Oil Tube .........................................................................................

Felt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Felt, Oil Attraction ............................................................................Screw, for clamp ...............................................................................Clamp, for oil tube .............................................................................Needle Bar Bushing, upper ..................................................................

1 6

No. 3As viewed

from the side

TORQUE:19-21 in. lbs.2.1-2.3 Nm

TORQUE:24-26 in. lbs.(2.7-2.9 Nm)

TORQUE:38 in. lbs.(4.3 Nm)

NOTE:Cut-out in Ref. No.38 & 39 to be upwhen assembling


41

TORQUE:Ref. No. 41, 42, 43

19-21 in. lbs.2.1-2.3 Nm


12

34

78

10

65

9

15

1617

18

11

12

13

14

19

27

2221

20

23

2425 26

2829

30

32

31

32

3435

3736

38

39

40

42

4445

43

43

42

484746

50

5253

5455

56

4951

59

61

62

63

60

NOTE:See "Aligning main shaft to

crankshaft" in adjustingmanual for torque sequence

33

5758

1 7


Ref.No.

CRANKSHAFT, NEEDLE LEVER, NEEDLE BAR & LOOPER DRIVE MECHANISM

1 .2 .3 .4 .5 .6 .7 .8 .9 .

10.11.12.13.14.15.16.17.18.19.2 0 .21.22.23.24.25.26.27.28.29.30.

Screw, for needle lever assembly ...........................................................Washer ...........................................................................................Washer ...........................................................................................Gasket, for thrust collar ......................................................................"O" Ring ...........................................................................................Collar .............................................................................................Torlon Washer ..................................................................................Needle Lever Assembly .......................................................................

Needle Lever ...............................................................................Bushing ................................................................................

Screw ........................................................................................Link, for needle bar .......................................................................Needle Bar Connection ..................................................................

Screw ..... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Screw ........................................................................................Retaining Ring .............................................................................Link Pin ......................................................................................

Oil Wick ................................................................................Needle Lever Stud ......................................................................

"O" Ring ...... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Screw, for needle lever eyelet ................................................................Needle Lever Thread Eyelet ...............................................................Ball Joint, for needle lever ...................................................................Screw, for ball joint ............................................................................Washer, for ball joint ..........................................................................Nut, for ball joint ................................................................................Needle Lever Connecting Rod ..............................................................Retaining Plate ..................................................................................Screw, for handwheel ..........................................................................Handwheel .......................................................................................

111111211111111422111112112131

22586R51250V51250D56382AK660-62556350J56350K29348AF56315A56350G7756354D51254K22562A22564660-21552336AWO356350D660-6252276854458-929105BC22559G51216N51216P5631661321L2257457821A


1 8

No. 3As viewedfrom the

side


TORQUE:24-26 in. lbs.(2.7-2.9 Nm)


NOTE:Cut-out in Ref. No.38 & 39 to be upwhen assembling


41

TORQUE:Ref. No. 41, 42, 43

19-21 in. lbs.2.1-2.3 Nm


12

34

78

10

65

9

15

1617

18

11

12

13

14

19

27

22

2120

23

2425 26

2829

30

32

31

32

3435

3736

38

39

40

42

4445

43

43

42

484746

50

5253

5455

56

4951

59

61

62

63

60

NOTE:See "Aligning main shaft to

crankshaft" in adjustingmanual for torque sequence

33

5758

1 9


Ref.No.

31.32.33.34.35.36.37.38.39.40.41.42.43.44.45.46.47.48.49.50.51.52.53.54.55.56.57.58.59.60.61.62.63.

56321R22894AB660-20229476PC51216M56316C12934A5789359493A56343F22653L822894C22894D29105AK22587K56343C56343E22559A52942AF34342J22652A1257849C660-20256390H52951C56342K22882C51242MCL2131117A27-435BLK56958A22768

Pulley . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Screw .......................................................................................

"O" Ring ...........................................................................................Crankshaft Assembly .......................................................................

Needle Bearing ..........................................................................Connecting Rod Guide ........................................................................Nut, for connecting rod guide ................................................................Oil Pump Assembly, head (see page 15, ref. no. 29) ......................................Oil Pump Assembly, base (see page 15, ref. no. 1) .......................................Coupling, for looper drive lever .............................................................

Screw, for looper drive lever coupling ..............................................Set Screw, for looper drive lever coupling ...............................................Spot Screw, for looper drive lever coupling ..............................................Looper Lever Crank Assembly ...............................................................

Screw .... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Ball Joint Guide ............................................................................Oil Splasher ................................................................................Screw .......................................................................................

Looper Drive Lever Rocker Shaft ............................................................Binder Clamp ...................................................................................

Screw ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Thrust Washer .................................................................................."O" Ring ...........................................................................................Washer ...........................................................................................Thrust Washer ..................................................................................Looper Drive Lever ......................................................................................Screw ..........................................................................................................Washer .........................................................................................................Oil Wick .......................................................................................................Needle Bar .......................................................................................................Washer, for needle bar thread eyelet .............................................................Needle Bar Thread Eyelet ...........................................................................Screw, for needle bar thread eyelet ..............................................................

1211

281111222212112111111111111111

CRANKSHAFT, NEEDLE LEVER, NEEDLE BAR & LOOPER DRIVE MECHANISM (CONT.)


2 0

T O R Q U E :24-26 in. lbs.(2.7-2.9 Nm)

T O R Q U E :19-21 in. lbs.2.1-2.3 Nm

T O R Q U E :19-21 in. lbs.2.1-2.3 Nm

27

1 0

6

1112

1120

19

18

17

16

8

7

45

6

3

22

23

24 25

2622

26

302928

34

3536

43 4445

12

42

21

159

31

32

33

3738 39

40

47

41

46

1413

2 1


Ref.No.

SPREADER MECHANISM DRIVE

121122211141111111111121222111121111111121211112

Spreader .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Screw .... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Auxiliary Spreader ..............................................................................Spreader Holder ................................................................................

Screw .... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Screw .......................................................................................

Thrust Washer ...................................................................................Spreader Holder Drive Shaft ................................................................

Oil Wick .....................................................................................Carrier Connecting Rod Assembly ..........................................................

Screw .......................................................................................Oil Pad .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Oil Wick ..................................................................................Screw .... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Washer, ball .....................................................................................Washer, for carrier connecting rod assembly .......................................Nut, for carrier connecting rod assembly ..............................................Spreader Rocker Shaft Arm .................................................................

Locking Stud .............................................................................Washer .....................................................................................Nut ............................................................................................................

Wick, for spreader rocker shaft collar ..........................................................."O" Ring, for spreader rocker shaft ........................................................Spreader Rocker Shaft ........................................................................Crankshaft Thrust Collar .....................................................................

Screw ........................................................................................Washer ...........................................................................................Spreader Rocker Shaft Collar, inner ........................................................

Nut ...........................................................................................Washer ......................................................................................Locking Stud ..............................................................................

Screw, for spreader connecting rod ball joint, upper ...................................Spreader Connecting Rod Ball Joint, upper ...............................................Segment Lever ..................................................................................

Locking Stud ..............................................................................Washer .....................................................................................Nut .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Nut, for spreader connecting rod ball joint ................................................Washer ...........................................................................................Spacer ............................................................................................Connecting Rod .................................................................................Spreader Drive Eccentric Assembly ......................................................

Screw ........................................................................................Retaining Washer ........................................................................Retaining Ring .............................................................................

Spacer Washer .................................................................................Counterweight ..................................................................................Screw, for counterweight ....................................................................

57845D22738B57845F57845G779441332J34847AWO357848E2272915430LWI309357835M201857849A55235D6042A55235ECL35999-23252849578479557849C57849D55235E6042A55235D22559G29105BD52952C55235D6042A55235E18HA20A57852B5291629126CR22597A52951B660-24652951C52947A22587H

1 .2 .3 .4 .5 .6 .7 .8 .9 .

10 .11.12.

-13.14.15.16.17.18.19.20.21.22.23.24.25.26.27.28.29.30.31.32.33.34.35.36.37.38.39.40.41.42.43.44.45.46.47.

2 2

1

1 41 3

1 1

1 61 51 2

1 91 8

1 7

1 0

2 2

2 1

2 02 3

9854

3

2

1

6 7

2 6

2 7

3 2

3 3

3 53 6

3 43 7

3 8

4 74 2

4 4

4 6

4 5

3 9

4 04 1

4 2

4 44 3

4 8

4 9


TORQUE:19-21 in. lbs.2.1-2.3 Nm2 9

2 82 4

2 5

2 93 1

3 0

2 3


Ref.No.

LOOPER ROCKER & CONNECTING ROD

1 .2 .3 .4 .5 .6 .7 .8 .9 .

10.11.12.13.14.15.16.17.18.19.20.21.22.23.24.25.26.27.28.29.30.31.32.33.34.35.36.37.38.39.40.41.42.43.44.45.46.47.48.49.

51244L5124656344C9 87199 62287451236J56344BCO67EWO35634455244G51244N51216N1856342K22882C2051908C2451909E2451909F241829192AH5174556913B2256515465F882582282956393J87U5784122729C26951240D1856341N56341V56341T660-21056341W660-31056341P56341S56341R20627

Thrust Washer ..................................................................................Nut, for looper rocker assembly ............................................................Looper Rocker Frame ..........................................................................

Set Screw ...................................................................................Stop Screw .................................................................................

Spot Screw, for looper rocker frame ......................................................Lock Screw, for looper rocker frame ....................................................Connecting Pin ..................................................................................Looper Rocker Arm ............................................................................Cork Plug, for looper rocker shaft .........................................................Wool Yarn, for looper rocker shaft ......................................................Looper Rocker Shaft ...........................................................................Stud, for looper rocker shaft collar ........................................................Looper Rocker Shaft Collar ...................................................................Washer, for shaft stud .......................................................................Nut, for shaft stud ..............................................................................Looper Drive Lever ............................................................................

Screw .......................................................................................Washer ......................................................................................

Front Looper ...................................................................................Middle Looper ..................................................................................Rear Looper ....................................................................................Nut .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Looper Rocker Assembly ....................................................................

Stud Looper Rocker Cone ................................................................Looper Rocker .............................................................................

Set Screw ...........................................................................Cone .........................................................................................

Set Screw ............................................................................Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Screw ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Ball Joint Oiler ..................................................................................Screw , for ball joint oiler ..................................................................Looper Connecting Rod Ball Joint .........................................................

Screw .......................................................................................Nut, left hand thread ...........................................................................Looper Connecting Rod .......................................................................Nut, right hand thread .........................................................................Looper Connecting Rod Assembly, right .............................................

Spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .P in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Retaining Ring .............................................................................Pin .... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Retaining Ring .........................................................................Looper Connecting Rod .............................................................Lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Housing ....................................................................................

Washer ...........................................................................................Screw ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2111111111111111111111111131211111211111121211111

2 4

11

29 30

3332

1

109

41 4042

54

5 7

50

52

56

3

36

38

52

16

784

4

2 8

15

121314

1 8

16

17

1 8 19

28

TORQUE:19-21in. lbs.(2.1-2.3Nm)

31

34

35

39

37

36


43

45

46

48TORQUE:55 in. lbs.(6.2 Nm)

47

55

46

53

51

49

44

26 27

25 2423

2 0

22

21

2 5


Ref.No.

FEED MECHANISM, MAIN SHAFT & TAKE-UP

1 .2 .3 .4 .5 .6 .7 .8 .9 .

10.11.12.13.14.15.16.17.18.19.20.21.22.23.24.25.26.27.28.29.30.

660-10095638456335B22651CD456334B56335L56335D9841391660-43856334N22651CB422637P24258A6042A22863C56334L61341J22834A- - - - - -51236JWO32252856525D2280122875H61434G56122A56322B22891B

Needle Bearing ...............................................................................Seal ...............................................................................................Feed Rocker .....................................................................................

Screw .......................................................................................Feed Bar Shaft ..................................................................................Feed Rocker Shaft ..............................................................................Feed Rocker Shaft Collar .....................................................................

Screw ........................................................................................Feed Rocker Shaft Thrust Washer ...........................................................Retaining Ring ...................................................................................Feed Bar Assembly .............................................................................

Screw ........................................................................................Feed Dog Height Adjusting Screw ......................................................Nut ...........................................................................................Washer, for feed dog holder ..........................................................Feed Dog Holder Adjusting Screw .....................................................Feed Dog Holder ..........................................................................

Feed Bar Washer ................................................................................Needle Guard Adjusting Screw .............................................................Feed Dog (See Page 35) ........................................................................Link Pin ...........................................................................................

Oil Wick ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Screw, for feed dog ............................................................................Needle Guard ...................................................................................

Screw .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Screw, for needle guard ......................................................................Washer .... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Main Shaft ......................................................................................

Gasket ..... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Oil Flow Regulating Screw ...........................................................

221211121111111112211111111111


2 6

11

29 30

3332

1

109

41 4042

54

5 7

50

52

56

3

36

38

52

16

784

4

2 8

15

121314

1 8

16

17

1 8 19

28


31

34

35

39

37

36


43

45

46

48TORQUE:55 in. lbs.(6.2 Nm)

47

55

46

53

51

49

44

26 27

25 2423

2 0

22

21

2 7


Ref.No.

31.32.33.34.35.36.37.38.39.40.41.42.43.44.45.46.47.48.49.50.51.52.53.54.55.56.57.

29476NM08022894AA7739543N56323B22580D29476NM06222894AA7756336D660-269B22543A5633622798C56322C22525A21657E26956335S55235D6042A55235E7756336K56336C51236JWO3

Feed Lift Eccentric Assembly, .080", (2.03 mm) throw ..............................Set Screw ...................................................................................Screw .......................................................................................

Thrust Washer, for feed bar ................................................................Looper Thread Take-Up .......................................................................

Set Screw ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Looper Avoid Eccentric Assembly, .062", (1.58 mm) throw ..........................

Set Screw ..................................................................................Screw ........................................................................................

Feed Crank Stud Insert .......................................................................Quad Ring ........................................................................................Stitch Regulating Screw ......................................................................Feed Crank Stud, marked "A" ................................................................Screw .............................................................................................Main Shaft Head Plate ........................................................................Screw .............................................................................................Washer ...........................................................................................Nut, left thread ..................................................................................Feed Rocker Arm ...........................................................................

Locking Stud .............................................................................Washer .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Nut ...........................................................................................

Screw, for link pin .............................................................................Feed Crank Link Pin ..........................................................................

Feed Crank Link Ferrule .............................................................Feed Crank Link ................................................................................

Oil Wick .....................................................................................

111212111111111411111111111


FEED MECHANISM, MAIN SHAFT & TAKE-UP (CONT.)

2 8

3

12

76

5

4

9

1 0

1 1

1 2

8

1 3

1 5

1 41 6

181 7

1 9

2 02 1

2 2

2 3 2 4

2 5

2 6

2 9


Ref.No.

12111111111111111111111111

1.2.3 .4 .5 .6 .7 .8 .9 .

10.11.12.13.14.15.16.17.18.19.20.21.22.23.24.25.26.

50356B22564D51257K51257M22596F22892E3488399392A5788322557G56383D34383BA57893B51256C5635656383AB39552C660-20751283H53783N2253721657Y4022259621657W660-283A

Collar, for presser bar stop ..................................................................Screw, for collar ..........................................................................

Presser Bar .....................................................................................Presser Bar Guide ............................................................................Screw .............................................................................................Screw, for presser bar guide .................................................................Lifter Lever Link ................................................................................Screw, for lifter lever link ....................................................................Spacer Bushing ...............................................................................Screw ...... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Spring, for lifter lever .....................................................................Lifter Lever ......................................................................................Head Oil Tube Clamp ...........................................................................Presser Bar Spring ............................................................................Regulator, for presser spring ............................................................Li f ter Rod ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Washer, for lifter lever ........................................................................"O" Ring, for lifter lever .......................................................................Lifter Lever ......................................................................................Lifter Lever, internal ........................................................................

Screw .......................................................................................Lifter Lever Connection, tension release ..................................................

Screw ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Screw .......................................................................................

Lifter Lever Shaft ..............................................................................Retainer Washer ................................................................................

PRESSER FOOT LIFTER MECHANISM

3 0

INTERLEAF

3 1


Ref.No.

THREAD TENSION ASSEMBLY

1 .2 .3 .4 .5 .6 .7 .8 .9 .

10.11.12.13.

-14.15.

--

29477NKNS6110420SP5786557892M57892K21657AP56392GB3120704000B3126012000B312035200056392H51292F8B3101804000B3103804000B311270400056392R56392L56392M

Thread Tension Assembly ...................................................................Nut ...........................................................................................Lead-In Thread Guide ....................................................................Tension Post Support ...................................................................Tension Thread Eyelet ..................................................................Tension Disc Separator ................................................................Tension Post ..............................................................................Tension Disc Felt .........................................................................Tension Disc ..............................................................................Tension Disc Felt .........................................................................Spring Shield ..............................................................................Spring, needle thread tension (neutral) ...........................................Spring, spreader thread tension (red) ..............................................Spring, looper thread tension (blue) .................................................Ferrule, tension spring ...................................................................Knob, needle thread tension (neutral) ................................................Knob, spreader thread tension (red) ................................................Knob, looper thread tension (blue) ..................................................

17717177

14773137313

3 2

2

3

4

5

1

43

43

8

6 7

9

1 0 11

12

12

13

1 3

1 31 4 1 5

1 6

1 7

151 8

1 9

2 0

2 1

2 3

2 2

2 4

2 5 2 6

3 3


Ref.No.

11331113411232123811112312

56381-21251281AC35772H22760A22845BG51381BDG51382BA2284899295G51381BA5638051280J660-3132252418-14242283922585A2252456382G56382AW51282AJ52978Z25S22526C56301F22839C

Cloth Plate Cover ..............................................................................Cloth Plate Cover Spring ................................................................Spring Washer .............................................................................Screw, for spring washer ...............................................................Screw .......................................................................................

Oil Shield, rear ..................................................................................Bracket, for oil shield .........................................................................Screw, for oil shield bracket ...........................................................Screw, for oil shield, left rear..........................................................Oil Shield, left ...................................................................................Throat Plate Support ..........................................................................

Dowel Pin ..................................................................................Well Nut .........................................................................................Screw, for throat plate ........................................................................Screw, for throat plate support ........................................................Screw, for throat plate support ........................................................Screw, for oil reservoir cover, back ...................................................Screw, for oil reservoir cover, top .....................................................Oil Reservoir Cover, top .....................................................................Gasket ............................................................................................Hinged Oil Shield ..............................................................................Shim .... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Screw, for hinged oil shield .................................................................Screw, for cloth plate ........................................................................Cloth Plate ......................................................................................Screw, for cloth plate .........................................................................

COVERS & MISCELLANEOUS PARTS

1 .2 .3 .4 .5 .6 .7 .8 .9 .

10.11.12.13.14.15.16.17.18.19.20.21.22.23.24.25.26.

3 4

INTERLEAF

3 5


Ref.No.

PRESSER FOOT, THROAT PLATE & FEED DOG

1 .2 .3 .4 .5 .6 .7 .8 .9 .

10.11.12.13.

50318W242828C50342BCA9770S2451390K9122840A51430F51930L22779AK57824G2451405AG24

Needle Head ...................................................................................Screw ........................................................................................Set Screw ...................................................................................Thread Eyelet ..............................................................................

Presser Foot ....................................................................................Presser Foot Shank ......................................................................

Screw .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Screw ..... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Nut .... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Presser Foot Bottom ...................................................................Hinge Screw ...............................................................................

Throat Plate ....................................................................................Feed Dog .... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1131111111111

3 6

1

2 3

9

13

1 2

1 1

7 1 02 9

2 72 8

2 7

2 9

9

2 4

8 2 2

5

6

71 1

1 0

1 3

2 4

2 6

2 5

2 3

2 1

1 9

2 0

4

4

1 7

1 8

1 61 5

1 5

1 4

2

1 2

3

3 7


Ref.No.

CHAIN CUTTER ASSEMBLY

FOR STYLE FS113L112MBV096

1 .2 .3 .4 .5 .6 .7 .8 .9 .

10.11.12.13.14.15.16.17.18.19.20.21.22.23.24.25.26.27.28.29.

CL80-0511-01CL01-3066-41CL02-1689-01CL01-3066-51CL33-3204-04CL02-1649-01CL10-1385-01CL02-1640-01CL30-1133-01CL33-2106-03CL30-2700-01CL02-1642-01CL01-3066-11CL02-1657-02CL01-3057-02CL02-1647-01CL02-1648-01CL02-1673-01CL30-2750-01CL02-1613-01CL02-1645-01CL02-1650-01CL30-1385-01CL01-6003-035CL01-1819-11CL02-1644-01CL30-1280-01CL02-1641-01CL33-0308-05

Chain Cutter Assembly .....................................................................Screw, for guard .........................................................................Exhaust Tube .............................................................................Screw, for main body ....................................................................Screw, for hold-down plate .........................................................Plate, hold-down .........................................................................Piston Stop Cushion ......................................................................Body, Driver ...............................................................................Hose Fitt ing ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Set Screw, for end cap................................................................."O" Ring, for end cap ...................................................................End Cap ......... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Screw, for end cap ....................................................................Guard ..... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Screw, for stationary blade ..........................................................Blade, stationary .........................................................................Blade, movable .........................................................................Pin .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Spring ..... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Bushing .....................................................................................Main Body ................................................................................Stud ..... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Rubber Mount .............................................................................Screw, for piston .........................................................................Bushing ....................................................................................Sl ide .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ."O" Ring, for piston .....................................................................Piston .......................................................................................Screw, for driver body ..............................................................

11142121222221411111113111212

3 8

1

1 8

1 9

6

78

9

1 0

1 1

1 8

1 7

1 6

1 5

1 41 3

1 2

5

4

2

3

3 9


Ref.No.

SHUTTLE VALVE ASSEMBLY


1 .2 .3 .4 .5 .6 .7 .8 .9 .

10.11.12.13.14.15.16.17.18.19.

CL80-0512-01CL33-1710-01CL33-2010-16CL01-4174-01CL30-0593-01CL30-2122-01CL30-1749-01CL30-0819-01CL30-2145-01CL30-1134-01CL30-1615-01CL02-1662-01CL30-1540-01CL30-1781-01CL30-1691-01CL30-2310-01CL33-0106-12CL30-2385-01CL30-1106-01

Shuttle Air Valve Assembly ...............................................................Washer ......................................................................................Screw .... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Spacer, for grommet ...................................................................Grommet .... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Actuator ....................................................................................Coupling ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Flow Control ............................................................................Tee .... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Tubing ......................................................................................Quick Dump Valve ......................................................................Bracket .....................................................................................Tubing ......................................................................................Elbow .... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Fitt ing .... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Valve .......................................................................................Screw, for bracket ......................................................................Muffler .... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Fitt ing .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1111111111111111231

4 0

Compressed Air Inlet

Suction Inlet ToChain Cutter

1

Exhaust Outlet ToMuffler & Cut ChainBag Unit

2

3

4 1


Ref.No.

MUFFLER/ CHAIN RECOVERY SYSTEM


1 .2 .3 .

TBV200671B50MPL100MOD

Chain Removal Assembly .................................................................Cut Chain Bag Unit .............................................................................Muffler Unit .....................................................................................

111

4 2

1 1

1

1 1

1 6

1 59

1 0

1 4

1 3

5

1 2

2

3

4

5

6

7

8

4 3


Ref.No.

TREADLE OPERATED AIR VALVE ASSEMBLY


1 .2 .3 .4 .5 .6 .7 .8 .9 .

10.11.12.13.14.15.16.

CL80-6093-02CL30-0148-01CL33-2810-04CL30-0290-01CL33-2210-04CL33-1610-01CL33-1410-06CL01-6930-01CL30-1132-01CL30-0284-01CL30-0931-01CL01-2491-01CL01-5406-01CL01-2488-01CL30-0283-01CL01-2492-01

Air Valve Assembly, treadle operated ...................................................Collar .......................................................................................Set Screw, for collar ..................................................................Spring ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Set Screw, for actuator ..................................................................Hex Nut, for actuator ..................................................................Screw, for actuator housing .......................................................Limit Button ...............................................................................Air Valve ....................................................................................Elbow .......................................................................................Ball Joint ...... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Treadle Rod, upper ......................................................................Actuator ....................................................................................Housing ....................................................................................Air Fitting ...................................................................................Treadle Rod, lower .......................................................................

1111411111211111

4 4

Air In

1

Air Pressure50 PSI(3.45 Bars)

8

Air ToAir Valve

9

2

8

1 0

1 1

3

1 31 4

Air FromAir Valve

5

4

Air ToVenturi

6

9

Air ToCutter

7

1 2

4 5


Ref.No.

FILTER, REGULATOR, LUBRICATOR, GAUGE ASSEMBLY


1 .2 .3 .4 .5 .6 .7 .8 .9 .

10.11.12.13.14.

CL80-0415-04CL01-4528-01CL30-0899-01CL30-0287-01CL30-0840-01CL30-2146-01CL30-2347-01CL33-2010-12CL30-0284-01CL30-0277-01CL30-1048-01CL30-0283-01CL30-0280-01CL01-6351-01

Filter, Regulator, Lubricator, Gauge Assembly ......................................Bracket .... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Mounting Nut ...............................................................................Tubing .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Tee ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Gauge .......................................................................................Filter, Regulator, Lubricator .......................................................Screw, for bracket ......................................................................Elbow ........................................................................................Male Disconnect ...........................................................................Female Disconnect ......................................................................Air Fitt ing .................................................................................Tee ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Blind Nipple .............................................................................

11111112211111

AIR CIRCUIT DIAGRAM


4 6

NOTES

4 7

4 8

7

8

6

5

4

3

1*

2

4 9


Ref.No.

1 .2 .3 .4 .5 .6 .7 .8 .9 .

21101W828604RG21201660-240660-264421D3451295B51295A660-457

*Thread Stand ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Container of Oil (1 pint) .......................................................................Screwdriver .....................................................................................Thread Tweezers ............................................................................."S" Hook ........................................................................................Chain ..... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Isolator ..........................................................................................Isolator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Plastic Cover (not shown) ....................................................................

111121311

ACCESSORIES

*Note: Thread Stand to be setup for (7) thread cones only.Install 7th cone support disc on second mounting hole of short support bracket.Also transfer one of the two plastic eyelet inserts of the thread guide bracket to thesecond hole to ensure thread is pulled off cone properly.

50

1 2 9 3 4 A . . . . . . . . . . . 1 91 4 0 7 7 . . . . . . . . . . . 1 31 5 4 3 0 L . . . . . . . . . . 2 11 5 4 3 8 C . . . . . . . . . . 1 31 5 4 6 5 F . . . . . . . . . 2 31 5 8 A . . . . . . . . . . . . 1 11 8 . . . . . . . . . . . 2 1 , 2 31 8 - 1 4 2 4 . . . . . . . . . . . 3 32 0 . . . . . . . 1 1 , 2 1 , 2 32 1 1 0 1 W 8 . . . . . . . . . . 4 92 1 3 7 5 C E . . . . . . . . . . 1 12 1 6 5 7 A P . . . . . . . . . . 3 12 1 6 5 7 E . . . . . . . . . . 2 72 1 6 5 7 W . . . . . . . . . . . 2 92 1 6 5 7 X . . . . . . . . . . 1 52 1 6 5 7 Y . . . . . . . . . . 2 92 2 5 1 3 B . . . . . . . . . . 1 32 2 5 2 4 . . . . . . 1 1 , 3 32 2 5 2 5 A . . . . . . . . . . . 2 72 2 5 2 6 C . . . . . . . . . . . 3 32 2 5 2 8 . . . . . . . . . 2 52 2 5 3 7 . . . . . . . . . . . 2 92 2 5 3 9 A A . . . . . . . . . 1 32 2 5 3 9 A B . . . . . . . . . . 1 32 2 5 3 9 R . . . . . . . . . . 1 52 2 5 3 9 S . . . . . . . . . . 1 12 2 5 4 1 C . . . . . . 1 1 , 1 32 2 5 4 3 A . . . . . . . . . . 2 72 2 5 4 8 . . . . . . . . . . . 1 122557G. . . . . . . . . . . . .292 2 5 5 9 A . . . . . . . . . 1 92 2 5 5 9 G . . . . . . 1 7 , 2 12 2 5 6 2 A . . . . . . . . . 1 72 2 5 6 4 . . . . . . . . . 1 72 2 5 6 4 B . . . . . . . . . 1 32 2 5 6 4 D . . . . . . . . . 2 92 2 5 6 5 . . . . . . . . . 2 32 2 5 6 9 B . . . . . . . . . 1 52 2 5 6 9 C . . . . . . . . . 1 12 2 5 7 4 . . . . . . . . . 1 72 2 5 8 0 D . . . . . . 2 722585A....13 , 15, 332 2 5 8 5 C . . . . . . . . . . . 1 12 2 5 8 6 R . . . . . . . . . . . 1 72 2 5 8 7 H . . . . . . . . . . . . 2 12 2 5 8 7 K . . . . . . . . . . . . 1 92 2 5 9 6 . . . . . . . . . . . . 2 92 2 5 9 6 F . . . . . . . . . . . 2 92 2 5 9 7 A . . . . . . . . . 2 12 2 6 3 7 P 2 4 . . . . . . . . 2 52 2 6 5 1 C B 4 . . . . . . . . 2 52 2 6 5 1 C D 4 . . . . . . . . 2 52 2 6 5 2 A 1 2 . . . . . . . . . 1 92 2 6 5 3 L 8 . . . . . . . . 1 92 2 7 2 9 . . . . . . . . . 2 12 2 7 2 9 C . . . . . . . . 2 32 2 7 3 8 B . . . . . . . . 2 12 2 7 5 8 E . . . . . . . . . 1 32 2 7 6 0 A . . . . . . . . 3 32 2 7 6 6 . . . . . . . . 1 32 2 7 6 8 . . . . . . 1 7 , 1 9

2 2 7 7 9 A K . . . . . . 3 52 2 7 9 7 . . . . . . . . 1 32 2 7 9 8 C . . . . . . . . 2 72 2 8 0 1 . . . . . . . . 2 52 2 8 2 9 . . . . . . 1 1 , 2 32 2 8 3 4 A . . . . . . 2 52 2 8 3 9 . . . . . . . . . 3 32 2 8 3 9 C . . . . . . 1 1 , 3 32 2 8 4 0 A . . . . . . . . . 3 52 2 8 4 5 B . . . . . . . . . 3 32 2 8 4 8 . . . . . . 1 1 , 3 32 2 8 5 1 D . . . . . . . . . 1 32 2 8 6 3 C . . . . . . . . 2 52 2 8 7 4 . . . . . . . . 2 32 2 8 7 5 H . . . . . . . . . 2 522882C..............19, 232 2 8 8 9 H . . . . . . . 1 12 2 8 9 1 B . . . . . . . . 2 52 2 8 9 2 E . . . . . . . . . 2 92 2 8 9 4 A A . . . . . . . . . 2 72 2 8 9 4 A B . . . . . . . . . 1 92 2 8 9 4 C . . . . . . . . . 1 92 2 8 9 4 D . . . . . . . . . 1 92 2 8 9 4 E . . . . . . . . . 1 32 5 8 . . . . . . . . . . . . 2 32 5 8 A . . . . . . 1 5 , 2 52 5 S . . . . . . . . . . 3 32 6 9 . . . . . . 2 3 , 2 72 7 - 4 3 5 B L K . . . . . . 1 928.................11, 13, 352 8 6 0 4 R . . . . . . . . 4 92 8 C . . . . . . . . . . . 3 52 9 1 0 5 A K . . . . . . . . 1 92 9 1 0 5 B C . . . . . . . . 1 72 9 1 0 5 B D . . . . . . . . 2 12 9 1 2 6 C R . . . . . . . . 2 12 9 1 9 2 A H . . . . . . . . 2 32 9 3 4 8 A F . . . . . . . . 1 72 9 4 7 6 N M 0 6 2 . . . . 2 72 9 4 7 6 N M 0 8 0 . . . . 2 72 9 4 7 6 P C . . . . . . . . 1 92 9 4 7 7 N K . . . . . . . . . 3 13 1 1 1 7 A . . . . . . . . . 1 93 3 7 9 5 . . . . . . . . . 1 33 4 3 4 2 J . . . . . . . . . 1 93 4 3 8 3 B A . . . . . . . 2 93 4 7 5 8 . . . . . . . . . 1 33 4 8 3 1 C . . . . . . . . 1 33 4 8 4 4 D . . . . . . . . 1 33 4 8 4 7 A . . . . . . . . 2 13 4 8 8 3 . . . . . . . . 2 93 5 7 7 2 H . . . . . . . . . 3 33 5 8 9 7 B V . . . . . . . . 1 53 9 5 4 3 N . . . . . . . . 2 73 9 5 5 2 C . . . . . . . . 2 94 0 2 . . . . . . . . . . 2 94 1 3 3 2 J . . . . . . . . 2 14 1 3 9 1 . . . . . . . . 2 54 2 1 D 3 4 . . . . . . . . 4 94 3 2 9 6 A . . . . . . . . 1 35 0 - 8 9 5 B L K . . . . . . 1 5

5 0 3 1 8 W 2 4 . . . . . . 3 55 0 3 4 2 B C . . . . . . . . 3 55 0 3 5 6 B . . . . . . . . 2 95 1 - 9 0 2 B L K . . . . . . . . 1 55 1 1 5 4 E . . . . . . . . 1 55 1 2 1 6 M . . . . . . . . 1 95 1 2 1 6 N . . . . . . 1 7 , 2 35 1 2 1 6 P . . . . . . . . . . 1 751236J......23, 25, 275 1 2 4 0 D . . . . . . . . . 2 35 1 2 4 2 M . . . . . . . . . 1 95 1 2 4 4 L . . . . . . . . . 2 35 1 2 4 4 N . . . . . . . . . 2 35 1 2 4 6 . . . . . . . . . 2 35 1 2 5 0 D . . . . . . . . . . 1 75 1 2 5 0 V . . . . . . . . . . 1 75 1 2 5 4 K . . . . . . . . . . 1 75 1 2 5 6 C . . . . . . . . . . 2 95 1 2 5 7 A A . . . . . . . . . . 1 55 1 2 5 7 K . . . . . . . . 2 95 1 2 5 7 M . . . . . . . . . 2 95 1 2 8 0 J . . . . . . . . . 3 35 1 2 8 1 A C . . . . . . . . . 3 35 1 2 8 2 A J . . . . . . . . . 3 35 1 2 8 3 H . . . . . . . . . 2 95 1 2 9 2 F 8 . . . . . . . . . 3 15 1 2 9 5 A . . . . . . . . 4 95 1 2 9 5 B . . . . . . . 4 95 1 3 9 0 K . . . . . . . 3 55 1 4 0 5 A G 2 4 . . . . . . 3 55 1 4 3 0 F . . . . . . . . 3 55 1 4 5 7 B . . . . . . . . 1 15 1 4 9 2 . . . . . . . . 1 15 1 7 4 5 . . . . . . . . 2 35 1 7 5 8 . . . . . . . . . 1 15 1 9 0 8 C 2 4 . . . . . . . 2 35 1 9 0 9 E 2 4 . . . . . . . 2 35 1 9 0 9 F 2 4 . . . . . . . 2 35 1 9 3 0 L . . . . . . . 3 55 1 9 5 9 B . . . . . . . 1 15 1 9 5 9 D . . . . . . . . 1 15 1 9 5 9 J . . . . . . . 1 15 1 9 5 9 K . . . . . . . 1 15 2 3 3 6 A . . . . . . . 1 75 2 8 0 4 A . . . . . . . 1 15 2 8 4 9 . . . . . . . 2 15 2 8 8 3 R . . . . . . . 1 55 2 9 1 6 . . . . . . . 2 15 2 9 4 2 A B . . . . . . . 1 55 2 9 4 2 A F . . . . . . . 1 95 2 9 4 7 A . . . . . . . 2 15 2 9 5 1 B . . . . . . . 2 15 2 9 5 1 C . . . . . . 1 9 , 2 15 2 9 5 2 C . . . . . . . . 2 15 2 9 5 2 D . . . . . . . . 2 15 2 9 5 8 G . . . . . . . . 1 15 2 9 7 8 Z . . . . . . . . 3 35 3 7 8 3 N . . . . . . . . 2 95 3 9 . . . . . . . . . . . 1 15 4 4 5 8 - 9 . . . . . . . . . 1 75 5 2 3 5 D . . . . . . 2 1 , 2 7

5 5 2 3 5 E . . . . . . 2 1 , 2 75 5 2 4 4 G . . . . . . . . 2 35 6 1 2 2 A . . . . . . . . 2 55 6 1 9 0 . . . . . . . . . 1 55 6 3 0 1 F . . . . . . . . 3 35 6 3 1 5 A . . . . . . . 1 75 6 3 1 6 . . . . . . . . 1 75 6 3 1 6 C . . . . . . . . 1 95 6 3 2 1 R . . . . . . . . 1 95 6 3 2 2 B . . . . . . . 2 55 6 3 2 2 C . . . . . . . . . 2 75 6 3 2 3 B . . . . . . . . 2 75 6 3 3 4 B . . . . . . . . 2 55 6 3 3 4 L . . . . . . . 2 55 6 3 3 4 N . . . . . . . . 2 55 6 3 3 5 B . . . . . . . . 2 55 6 3 3 5 D . . . . . . . . 2 55 6 3 3 5 L . . . . . . . 2 55 6 3 3 5 S . . . . . . . 2 75 6 3 3 6 . . . . . . . 2 75 6 3 3 6 C . . . . . . . 2 75 6 3 3 6 D . . . . . . . 2 75 6 3 3 6 K . . . . . . . 2 75 6 3 4 1 N . . . . . . . 2 35 6 3 4 1 P . . . . . . . 2 35 6 3 4 1 R . . . . . . . 2 35 6 3 4 1 S . . . . . . . 2 35 6 3 4 1 T . . . . . . . 2 35 6 3 4 1 V . . . . . . . 2 35 6 3 4 1 W . . . . . . . . . 2 35 6 3 4 2 K . . . . . . 1 9 , 2 35 6 3 4 3 C . . . . . . . 1 95 6 3 4 3 E . . . . . . . 1 95 6 3 4 3 F . . . . . . . 1 95 6 3 4 4 . . . . . . . 2 35 6 3 4 4 B . . . . . . . 2 35 6 3 4 4 C . . . . . . . 2 35 6 3 5 0 D . . . . . . . 1 75 6 3 5 0 G . . . . . . . 1 75 6 3 5 0 J . . . . . . . 1 75 6 3 5 0 K . . . . . . . 1 75 6 3 5 4 D . . . . . . . 1 75 6 3 5 6 . . . . . . . 2 95 6 3 8 0 . . . . . . . 3 35 6 3 8 1 - 2 1 2 . . . . . . . 3 35 6 3 8 2 A A . . . . . . . 1 15 6 3 8 2 A B . . . . . . . 1 15 6 3 8 2 A C . . . . . . . 1 15 6 3 8 2 A K . . . . . . . 1 75 6 3 8 2 A U . . . . . . . 1 15 6 3 8 2 A V . . . . . . . 1 15 6 3 8 2 A W . . . . . . . 3 35 6 3 8 2 A X . . . . . . . 1 15 6 3 8 2 A Y . . . . . . . 1 15 6 3 8 2 D . . . . . . . 1 15 6 3 8 2 G . . . . . . . 3 35 6 3 8 2 J . . . . . . . 1 15 6 3 8 2 Y . . . . . . . 1 15 6 3 8 3 A B . . . . . . . 2 95 6 3 8 3 D . . . . . . . 2 95 6 3 8 4 . . . . . . . 2 5

Part No. Page No. Part No. Page No. Part No. Page No. Part No. Page No.

NUMERICAL INDEX OF PARTS

51

5 6 3 9 0 . . . . . . . 1 55 6 3 9 0 E . . . . . . . 1 55 6 3 9 0 G . . . . . . 1 55 6 3 9 0 H . . . . . . 1 5 , 1 95 6 3 9 0 J . . . . . . . . 1 55 6 3 9 1 B . . . . . . . 1 15 6 3 9 2 G . . . . . . . 3 15 6 3 9 2 H . . . . . . . 3 15 6 3 9 2 L . . . . . . . 3 15 6 3 9 2 M . . . . . . . 3 15 6 3 9 2 R . . . . . . . 3 15 6 3 9 3 J . . . . . . . 2 35 6 3 9 3 P . . . . . . . 1 55 6 3 9 3 Q . . . . . . . 1 55 6 3 9 3 W . . . . . . . 1 55 6 4 7 0 . . . . . . . 1 35 6 5 2 5 D . . . . . . . 2 55 6 5 2 5 E . . . . . . . 1 35 6 5 2 5 F . . . . . . . 1 35 6 9 1 3 B . . . . . . . 2 35 6 9 5 8 A . . . . . . . 1 95 7 7 8 2 M . . . . . . . 1 15 7 8 2 1 A . . . . . . . 1 75 7 8 2 4 G 2 4 . . . . . . . 3 55 7 8 3 5 M . . . . . . . 2 15 7 8 3 6 B . . . . . . . 1 55 7 8 4 1 . . . . . . . 2 35 7 8 4 2 B . . . . . . . 1 55 7 8 4 4 . . . . . . . 1 15 7 8 4 4 C . . . . . . . 1 35 7 8 4 5 D . . . . . . . 2 15 7 8 4 5 E . . . . . . . 1 35 7 8 4 5 F . . . . . . . 2 15 7 8 4 5 G . . . . . . . 2 15 7 8 4 7 . . . . . . . 2 15 7 8 4 7 B . . . . . . . 1 55 7 8 4 8 E . . . . . . . 2 15 7 8 4 9 . . . . . . . 1 55 7 8 4 9 A . . . . . . . 2 15 7 8 4 9 C . . . . . . 1 95 7 8 4 9 D . . . . . . . 2 15 7 8 5 2 B . . . . . . . 2 15 7 8 5 4 . . . . . . . 1 55 7 8 5 8 A . . . . . . . 1 35 7 8 5 8 B . . . . . . . 1 35 7 8 5 8 C . . . . . . . 1 15 7 8 6 5 . . . . . . . 3 15 7 8 8 2 J . . . . . . . 1 15 7 8 8 2 K . . . . . . . 1 35 7 8 8 2 P . . . . . . . 1 35 7 8 8 3 . . . . . . . 2 95 7 8 9 0 B . . . . . . . 1 55 7 8 9 2 C 5 . . . . . . . 1 15 7 8 9 2 H . . . . . . . 1 15 7 8 9 2 J . . . . . . . 1 15 7 8 9 2 K . . . . . . . 3 15 7 8 9 2 M . . . . . . . 3 15 7 8 9 3 . . . . . . 1 5 , 1 95 7 8 9 3 A . . . . . . . 1 55 7 8 9 3 B . . . . . . . 2 95 7 8 9 3 C . . . . . . . 1 5

5 7 W B . . . . . . . 1 35 7 W D . . . . . . . . . . . . . 1 35 9 4 9 3 A . . . . . . 1 5 , 1 96 - 6 7 - 1 2 5 . . . . . . . . . . . . 1 56042A. . . . . .21 , 25 , 276 1 3 2 1 L . . . . . . . . . . . 1 76 1 3 4 1 J . . . . . . . . . . . . 2 56 1 4 3 4 G . . . . . . . . . . . . . 2 56 2 7 . . . . . . . . . . . . . . 2 36 6 0 - 1 0 0 2 . . . . . . . . . . . 1 16 6 0 - 1 0 0 9 . . . . . . . . . . . 2 56 6 0 - 2 0 2 . . . . . . . . . . . . 1 96 6 0 - 2 0 7 . . . . . . . . . . . . 2 96 6 0 - 2 1 0 . . . . . . . . . . . . . 2 36 6 0 - 2 1 5 . . . . . . . . . . . . . 1 76 6 0 - 2 3 0 . . . . . . . . . . . . . 1 56 6 0 - 2 4 0 . . . . . . . . . . . . . 4 9660 -246 . . . . . . . . . . . . . .2 16 6 0 - 2 6 4 . . . . . . . . . . . . . 4 96 6 0 - 2 6 9 B . . . . . . . . . . 2 76 6 0 - 2 8 3 A . . . . . . . . . 2 96 6 0 - 3 1 0 . . . . . . . . . . . 2 36 6 0 - 3 1 3 . . . . . . . . . . . 3 36 6 0 - 4 0 6 . . . . . . . . . . . 1 56 6 0 - 4 3 8 . . . . . . . . . . . 2 56 6 0 - 4 5 7 . . . . . . . . . . . 4 96 6 0 - 6 1 7 . . . . . . . . . . . 1 36 6 0 - 6 2 5 . . . . . . . . . . . 1 76 6 0 - 6 6 5 . . . . . . . . . . . 1 56 6 0 - 7 3 9 . . . . . . . . . . . . 1 56 6 6 - 2 1 4 . . . . . . . . . . . . 1 56 6 6 - 2 5 9 . . . . . . . . . . . . 1 56 7 1 B 5 0 . . . . . . . . . . . . 4 16 9 H . . . . . . . . . . . . . 1 17 1 9 . . . . . . . . . . . . . 2 377............13 ,17, 21, 278 0 5 5 7 . . . . . . . . . . . . . 1 18 0 6 6 5 F . . . . . . . . . . . . . 1 18 7 U . . . . . . . . . . . . 2 38 8 . . . . . . . . . . . . . . 2 39 0 . . . . . . . . . . . . 1 19 1 . . . . . . . . . . . 3 59 3 . . . . . . . . . . . 2 19 4 . . . . . . . . . . 2 19 5 . . . . . . 1 3 , 2 19 5 9 7 8 . . . . . . . . . . . 1 39 6 . . . . . . . . . 2 39 8 . . . . . . . . . 2 3 , 2 59 8 A . . . . . . . . . . 1 19 9 2 9 5 . . . . . . . . . 3 39 9 3 9 2 A . . . . . . . . 2 99 9 6 8 2 X C 2 . . . . . . . . 1 39 9 6 8 2 X F . . . . . . . . 1 39 9 6 8 3 C N . . . . . . . . . 1 39 9 6 9 6 A . . . . . . . . . 1 39 9 9 - 2 1 6 K . . . . . . . . . . 1 59 9 9 - 2 3 2 . . . . . . . . . 2 1A 9 7 7 0 S 2 4 . . . . . . . . . . 3 5B3101804000..........31B3103804000..........31B3112704000..........31

NUMERICAL INDEX OF PARTS

B3120352000............31B3120704000............31B3126012000............31C L 3 5 . . . . . . . . . . 2 1CL01-1819-11..........37CL01-2488-01. . . . . . . .43CL01-2491-01. . . . . . . .43CL01-2492-01. . . . . . . .43CL01-3057-02. . . . . . . .37CL01-3066-11. . . . . . . .37CL01-3066 -41 . . . . . . .37CL01-3066 -51 . . . . . . .37CL01-4174 -01 . . . . . . .39CL01-4528 -01 . . . . . . .45CL01-5406 -01 . . . . . . .43CL01-6003-035.. . . . . .37CL01-6351 -01 . . . . . . .45CL01-6930 -01 . . . . . . .43CL02-1613 -01 . . . . . . .37CL02-1640 -01 . . . . . . .37CL02-1641 -01 . . . . . . .37CL02-1642 -01 . . . . . . .37CL02-1644 -01 . . . . . . .37CL02-1645 -01 . . . . . . .37CL02-1647 -01 . . . . . . .37CL02-1648 -01 . . . . . . .37CL02-1649 -01 . . . . . . .37CL02-1650 -01 . . . . . . .37CL02-1657 -02 . . . . . . .37CL02-1662 -01 . . . . . . .39CL02-1673 -01 . . . . . . .37CL02-1689 -01 . . . . . . .37CL10-1385 -01 . . . . . . .37C L 2 1 . . . . . . . . . 1 5 , 1 9CL30-0148 -01 . . . . . . .43CL30-0277 -01 . . . . . . .45CL30-0280 -01 . . . . . . .45CL30-0283-01......43, 45CL30-0284-01......43, 45CL30-0287 -01 . . . . . . .45CL30-0290 -01 . . . . . . .43CL30-0593 -01 . . . . . . .39CL30-0819 -01 . . . . . . .39CL30-0840 -01 . . . . . . .45CL30-0899 -01 . . . . . . .45CL30-0931 -01 . . . . . . .43CL30-1048 -01 . . . . . . .45CL30-1106 -01 . . . . . . .39CL30-1132 -01 . . . . . . .43CL30-1133 -01 . . . . . . .37CL30-1134 -01 . . . . . . .39CL30-1280 -01 . . . . . . .37CL30-1385 -01 . . . . . . .37CL30-1540 -01 . . . . . . .39CL30-1615 -01 . . . . . . .39CL30-1691 -01 . . . . . . .39CL30-1749 -01 . . . . . . .39CL30-1781 -01 . . . . . . .39CL30-2122 -01 . . . . . . .39CL30-2145 -01 . . . . . . .39CL30-2146 -01 . . . . . . .45

Part No. Page No.

CL30-2310-01... . . . .39CL30-2347-01... . . . .45CL30-2385-01. . . . . .39CL30-2700-01........37CL30-2750-01... . . . .37CL33-0106-12... . . . .39CL33-0308-05... . . . .37CL33-1410-06... . . . .43CL33-1610-01... . . . .43CL33-1710-01... . . . .39CL33-2010-12... . . . .45CL33-2010-16... . . . .39CL33-2106-03... . . . .37CL33-2210-04... . . . .43CL33-2810-04... . . . .43CL33-3204-04... . . . .37CL80-0415-04... . . . .45CL80-0511-01... . . . .37CL80-0512-01... . . . .39CL80-6093-02... . . . .43C O 6 7 E . . . . . . . . . . . . 2 3G 2 1 2 0 1 . . . . . . . . . . . . 4 9G51381BA.. . . . . . . . . .33G51381BD.. . . . . . . . . .33G51382BA.. . . . . . . . . .33H A 2 0 A . . . . . . . . . . 2 1MPL100MOD.............41NS6110420SP.............31T B V 2 0 0 . . . . . . . . . . . 4 1W I 3 0 . . . . . . . . . . . . . 2 1WO3......17, 21, 23, 25, 27

Part No. Page No.Part No. Page No.Part No. Page No.

52

NOTES

NOTES

5 3

Date post:	04-Jul-2020
Category:	Documents
Upload:	others
View:	2 times
Download:	0 times

ILLUSTRATED PARTS LIST - Universal Sewing › images2 › parts_lists › all › ...ILLUSTRATED...

Documents