Illustrated Parts:

Cutter Bars 2013 +

Transmissions Bottom Bar Assembly

Self Adjusting Tensioners Hoods, Decals

Revised 12-14-15

BCS America LLC 5001 N Lagoon Ave Portland, OR 97217

www.bcsamerica.comPhone: 800-543-1040

Fax: 800-777-7069

ID PART NO DESCRIPTION DENOMINACION NOTES

Attachments2013+Cutter Bars

Serial Number Range

REVISED 12/10/15

01.0010000 - -------3 Dog PTO

Cutter Bar Control

1 300.00001 GREASE ZERK M10 ENGRASADOR M102 311.11165 SCREW, M8X100 TORNILLO M8X1003 311.12093 SCREW, M6X20 TORNILLO M6X204 311.12097 SCREW, M6X70 TORNILLO M6X705 311.12149 SCREW, M8X12 TORNILLO M8X12

6 311.12904 SCREW, M12X1.25X30 TORNILLO M12X1.25X307 311.21006 SCREW M6X16 TORNILLO M6X168 312.41061 NUT, SELF LOCKING, M6 TUERCA AUTOBLOC. M69 312.41080 NUT, SELF LOCKING, M8 TUERCA AUTOBLOC. M8

10 313.12076 STUD, M8X26 PRISIONERO M8X26

11 314.11084 WASHER, FLAT, M8.4 ARANDELA PLANA M8.412 314.24064 WASHER, LOCK, M6.4 ARANDELA DE RES. M6.413 342.11041 PIN, LOCKING, M4X35 ESPINA DE RES. M4X3514 351.11047 CIRCLIP, INTERNAL SEEGER INT.15 371.11150 BEARING, M15X35X11 COJINETE M15X35X11

16 371.12200 BEARING M20X47X14 COJINETE M20X47X1417 371.12253 BEARING, M25X52X15 COJINETE M25X52X1518 371.13201 BEARING, M20X52X15 COJINETE M20X52X1519 373.32001 BUSHING PIT CASQUILLO PIT20 512.43501 BUSHING WITH FLANGE CASQUILLO CON BRIDA

21 512.58953 BAR SUPPORT SOPORTE BARRA22 513.58950 SHAFT HOUSING CASQUILLO23 524.48969 BLADE CRANK MANIVELA CUCHILLA24 524.58955 ECCENTRIC SHAFT ARBOL EXCENTRICO25 524.58956 LONG ECCENTRIC SHAFT ARBOL EXCENTRICO LUNGO

26 525.48510 FORK HORQUILLA REFORCADA27 561.42291 WASHER ARANDELA28 561.43497 BOTTOM FONDO29 561.43506 SPACER SERPADOR30 561.43507 ECCENTRIC PROTECTION PROTECCION EXCENTRICA

31 561.43516 COVER, BEARING TAPA COJINETE32 561.49389 GUARD END TAPON PROTECCION33 561.58954 SPACER SEPARADOR34 564.46718 BLADE BUSHING CASQUILLO CUCHILLO35 564.58941 PTO COUPLER ACOPLAMIENTO FRESADORA

ID PART NO DESCRIPTION DENOMINACION NOTES

Serial Number Range

REVISED 12/10/15

Attachments2013+Cutter Bars 01.0010000 - -------

3 Dog PTOCutter Bar Control

36 571.40533 END, LOWER TAPON INFERIOR37 590.46719 BLADE PIN PERNO CUCHILLO38 590.48968 CRANK WITH FORK MANIVELA CON HORQUILLA

ID PART NO DESCRIPTION DENOMINACION NOTES

Attachments2013+Cutter Bars

Serial Number Range

REVISED 12/10/15

3 Dog PTOCutter Bar Control ------ - ------- 01.01

1 300.00001 GREASE ZERK M10 ENGRASADOR M102 311.11165 SCREW, M8X100 TORNILLO M8X1003 311.12093 SCREW, M6X20 TORNILLO M6X204 311.12097 SCREW, M6X70 TORNILLO M6X705 311.12149 SCREW, M8X12 TORNILLO M8X12

6 312.41105 LOCK NUT DEFORMED7 311.21006 SCREW M6X16 TORNILLO M6X168 312.41061 NUT, SELF LOCKING, M6 TUERCA AUTOBLOC. M69 312.41080 NUT, SELF LOCKING, M8 TUERCA AUTOBLOC. M8

10 313.12076 STUD, M8X26 PRISIONERO M8X26

11 314.11084 WASHER, FLAT, M8.4 ARANDELA PLANA M8.412 314.24064 WASHER, LOCK, M6.4 ARANDELA DE RES. M6.413 342.11041 PIN, LOCKING, M4X35 ESPINA DE RES. M4X3514 351.11047 CIRCLIP, INTERNAL SEEGER INT.15 371.11150 BEARING, M15X35X11 COJINETE M15X35X11

16 371.12200 BEARING M20X47X14 COJINETE M20X47X1417 371.12253 BEARING, M25X52X15 COJINETE M25X52X1518 371.13201 BEARING, M20X52X15 COJINETE M20X52X1519 373.32001 BUSHING PIT CASQUILLO PIT20 512.43501 BUSHING WITH FLANGE CASQUILLO CON BRIDA

21 513.58948 BAR SUPPORT SOPORTE BARRA22 513.58950 SHAFT HOUSING CASQUILLO23 524.58966 BLADE CRANK MANIVELA CUCHILLA24 524.58955 ECCENTRIC SHAFT ARBOL EXCENTRICO25 524.58956 LONG ECCENTRIC SHAFT ARBOL EXCENTRICO LUNGO

26 525.48510 FORK HORQUILLA REFORCADA27 561.42291 WASHER ARANDELA28 561.43497 BOTTOM FONDO29 561.43506 SPACER SERPADOR30 561.43507 ECCENTRIC PROTECTION PROTECCION EXCENTRICA

31 561.43516 COVER, BEARING TAPA COJINETE32 561.49389 GUARD END TAPON PROTECCION33 561.58954 SPACER SEPARADOR34 564.46718 BLADE PIN BUSHING 32MM CASQUILLO CUCHILLO35 564.58941 PTO COUPLER ACOPLAMIENTO FRESADORA

- 34 & 39 THESE BUSHING ARE32MM AND 37MM IN DIAMETER. INRARE CASES THE 32MM BUSHINGWILL BE USED. THE CAUSE FORTHE 32 MM TO BE USED IS WHEN A2000 AND BEYOND CUTTERBARTRANSMISSION IS USED WITH A 95-99 CUTTERBAR ASSEMBLY.

ID PART NO DESCRIPTION DENOMINACION NOTES

Serial Number Range

REVISED 12/10/15

Attachments2013+Cutter Bars

3 Dog PTOCutter Bar Control ------ - -------

36 571.40533 END, LOWER TAPON INFERIOR37 564.58967 BLADE PIN PERNO CUCHILLO38 590.58965 CRANK WITH FORK MANIVELA CON HORQUILLA39 564.46667 BLADE PIN BUSHING 37MM40 314.21101 WASHER SUPER

01.01

- 34 & 39 THESE BUSHING ARE32MM AND 37MM IN DIAMETER. INRARE CASES THE 32MM BUSHINGWILL BE USED. THE CAUSE FORTHE 32 MM TO BE USED IS WHEN A2000 AND BEYOND CUTTERBARTRANSMISSION IS USED WITH A 95-99 CUTTERBAR ASSEMBLY.

Attachments 2013 + Cutter

Bar 3 - Dog PTO Torx Oil Bath Control

Serial Number Range 474946 --------------- 02.00

ID PART NO DESCRIPTION ID PART NO DESCRIPTION

1 30000001 GREASE ZERK M10 17 37111349 BEARING 2 31112090 SCREW TE M6X16 UNI 5739 8G 18 37112203 BEARING 3 31112286 SCREW TE M12X130 UNI 5737 19 38112982 O-RING 4 31211100 NUT M10 Tighten to 50 nm 20 38204808 OIL SEAL AS 48x62x8 5 31241105 SELFLOCK NUT M10 21 38212502 OIL SEAL 25X52X7

6 31241120 SELFLOCK NUT M12 22 51346701 CRANK 7 31312114 STUD BOLT M10X50X22X14 23 51358885 SUPPORT A = 186 MM 8 31411130 WASHER 13x24 24 51358886 SUPPORT A = 267 MM 9 31421101 WASHER 25 51358887 BLADE CONTROL BOX

10 34211082 ROLL PIN B = 195 MM 26 51358961 SLEEVE B = 195 MM 11 34211087 ROLL PIN B = 114MM 27 51358963 SLEEVE B = 114 MM

12 34221080 CYLINDRICAL PLUG 28 52358852 CRANK CONTROL 13 35111062 SEEGER RING I 62 DIN 472 29 52458668 BARREL 14 35121060 SEEGER RING E 60 DIN 471 30 56142291 WASHER 7,0x25/4 15 37111152 BEARING 31 56358964 ADJUSTING RING SP=1,5 16 37111254 BEARING 32 56446667 SLEEVE OD 37 MM

Oil Bath Control Torx rev 6 & 7 10-26-15

Attachments 2013 + Cutter

Bar 3 - Dog PTO Torx Oil Bath Control

Serial Number Range 474946 --------------- 02.00

ID PART NO DESCRIPTION ID PART NO DESCRIPTION

33 56458851 SHAFT CONNECTING ROD 34 56458854 SPACER 35 56458941 COUPLING 36 56458957 CAM SHAFT C = 178 MM 37 56458958 CAM SHAFT C = 259 MM

38 56458967 PIN 39 58058855 LOCK NUT M24X2 Tighten to 200 nm 40 59051045 PLUG 41 511C0348 WEIGHT 33 LBS 42 922C0350 WEIGHT KIT

Oil Bath Control Torx rev 6 & 7 10-26-15

Attachments 2013 + Cutter

Bar 3 - Dog PTO

Laser Bar Bottom Bar Assembly 03.00

ID PART NO DESCRIPTION ID PART NO DESCRIPTION

1 31112152 SCREW TE M8X30 UNI 5739 8G 22 56158735 CENTRAL SPACER GALV 2 31112165 SCREW TE C/F M8X35 DIN 6921 8G 23 56158749 SKID SHOE 3 31112167 SCREW TE C/F M8X30 DIN 6921 8G 24 56351401 SMALL PLATE 4 31112169 SCREW TE C/F M8X40 DIN 6921 25 56358704 SLIDE BAR 45 " 5 31112171 SCREW TE C/F M8X16 DIN 6921 26 56358705 SLIDE BAR 53 "

6 31211080 NUT M8 27 56358708 BLADE SUPPORT 7 31221151 NUT M14X1,5 Tighten to 100 Ft lbs 28 56358716 BLADE SECTION 8 31241085 SELFLOCK NUT M8 6S 29 56358736 BAR CONNECTION 9 31312141 STUD BOLT 30 56358744 BLADE HOLDER GUIDE

10 31421251 DOME WASHER Dome side towards nut 31 56358781 SLIDE BAR 30 "

11 33126513 RIVET TC 6.5 X 13 32 56358782 SLIDE BAR 40 " 12 33126516 RIVET TC 6.5 X 16 33 56359003 BLANK HOLDER 13 52158700 BLADE COUPLING 34 58058661 CONICAL NUT M16X1.5 14 52158747 SKID SUPPORT / MOUNT 35 58058662 SCREW FOR BLADE CONNECTION 15 52158748 NUT RETAINER FOR SKID MOUNT

16 52458713 DOUBLE FINGER 36 59058724 BLADE ASSEBLY 30 " 15 SECTIONS 17 52458714 SINGLE FINGER 37 59058728 BLADE ASSEBLY 40 " 19 SECTIONS 18 55259131 GUARD 30 " 38 59058739 BLADE ASSEBLY 45 " 23 SECTIONS 19 55259132 GUARD 40" 39 59058740 BLADE ASSEBLY 53 " 27 SECTIONS 20 55259133 GUARD 45" 40 59258746 COMPLETE SKID ASSEMBLY ( 1 EACH ) 21 55259134 GUARD 53' 41 92290984 SKID ASSEMBLY KIT ( PAIR )

Note ( * ) = New Part / Change Laser Bar rev.0 10-19-15

Attachments 2013 + Cutter

Bar 3 - Dog PTO

Laser Bar Bottom Bar Assembly 03.01

ID PART NO DESCRIPTION ID PART NO DESCRIPTION

1 * 31112151 SCREW TE M8X25 UNI 5739 8G 22 56158735 CENTRAL SPACER GALV 2 31112165 SCREW TE C/F M8X35 DIN 6921 8G 23 56158749 SKID SHOE 3 31112167 SCREW TE C/F M8X30 DIN 6921 8G 24 56351401 SMALL PLATE 4 31112169 SCREW TE C/F M8X40 DIN 6921 25 56358704 SLIDE BAR 45 " 5 31112171 SCREW TE C/F M8X16 DIN 6921 26 56358705 SLIDE BAR 53 "

6 31211080 NUT M8 27 56358708 BLADE SUPPORT 7 31221151 NUT M14X1,5 Tighten to 100 Ft lbs 28 56358716 BLADE SECTION 8 31241085 SELFLOCK NUT M8 6S 29 56358736 BAR CONNECTION 9 31312141 STUD BOLT 30 56358744 BLADE HOLDER GUIDE

10 31421251 DOME WASHER Dome side toward nut 31 56358781 SLIDE BAR 30 "

11 33126513 RIVET TC 6.5 X 13 32 56358782 SLIDE BAR 40 " 12 33126516 RIVET TC 6.5 X 16 33 56359003 BLANK HOLDER 13 52158700 BLADE COUPLING 34 58058661 CONICAL NUT M16X1.5 14 52158747 SKID SUPPORT / MOUNT 35 58058662 SCREW FOR BLADE CONNECTION 15 52158748 NUT RETAINER FOR SKID MOUNT

16 52458713 DOUBLE FINGER 36 59058724 BLADE ASSEBLY 30 " 15 SECTIONS 17 52458714 SINGLE FINGER 37 59058728 BLADE ASSEBLY 40 " 19 SECTIONS 18 55259131 GUARD 30 " 38 59058739 BLADE ASSEBLY 45 " 23 SECTIONS 19 55259132 GUARD 40" 39 59058740 BLADE ASSEBLY 53 " 27 SECTIONS 20 55259133 GUARD 45" 40 59258746 COMPLETE SKID ASSEMBLY ( 1 EACH ) 21 55259134 GUARD 53' 41 92290984 SKID ASSEMBLY KIT ( PAIR )

Note ( * ) = New Part / Change Laser Bar Rev.1 10-19-15

Attachments 2013 + Cutter

Bar 3 - Dog PTO

Laser Bar Bottom Bar Assembly 03.02

ID PART NO DESCRIPTION ID PART NO DESCRIPTION

1 31112151 SCREW TE M8X25 UNI 5739 8G 23 56158735 CENTRAL SPACER BF2011 GALV 2 31112165 SCREW TE C/F M8X35 DIN 6921 8G 24 56158749 SKID SHOE 3 31112167 SCREW TE C/F M8X30 DIN 6921 8G 25 56351401 SMALL PLATE 4 31112169 SCREW TE C/F M8X40 DIN 6921 26 56358708 BLADE SUPPORT 5 31112171 SCREW TE C/F M8X16 DIN 6921 27 56358716 BLADE SECTION

6 31211080 NUT M8 28 56358736 BAR CONNECTION BF2011 7 31221151 NUT M14X1,5 Tighten to 100 Ft lbs 29 56358744 BLADE HOLDER GUIDE FB2011 8 31241085 SELFLOCK NUT M8 6S 30 * 56358781 SLIDE BAR 30 " 9 31312141 STUD BOLT 31 * 56358782 SLIDE BAR 40 "

10 31421251 DOME WASHER Dome side towards nut 32 * 56358783 SLIDE BAR 45 "

11 33126513 RIVET TC 6.5 X 13 33 * 56358784 SLIDE BAR 53 " 12 33126516 RIVET TC 6.5 X 16 34 56359003 BLANK HOLDER 13 52158700 BLADE COUPLING 35 58058661 CONICAL NUT M16X1.5 14 52158747 SKID SUPPORT / MOUNT 36 58058662 SCREW FOR BLADE CONNECTION 15 52158748 NUT RETAINER FOR SKID MOUNT 37 59058724 BLADE ASSEMBLY 30 " 15 SECTIONS

16 52458713 DOUBLE FINGER 38 59058728 BLADE ASSEMBLY 40 " 19 SECTIONS 17 52458714 SINGLE FINGER 39 59058739 BLADE ASSEMBLY 45 " 23 SECTIONS

18 * 53058751 LASER DECAL 40 59058740 BLADE ASSEMBLY 53 " 27 SECTIONS 19 55259131 GUARD 30 " 41 59258746 COMPLETE SLIDE FOR CUTTING BAR 20 55259132 GUARD 40 " 42 99290984 SKID ASSEMBLY KIT ( PAIR ) 21 55259133 GUARD 45 " 22 55259134 GUARD 53 "

Note ( * ) = New Part / Change Laser Bar Rev.2 10-19-15

Attachments 2013 + Cutter

Bar Adjustable 3 - Dog PTO Laser Bar

w/ Self-Adjusting Tensioners

Bottom Bar Assembly 03.07

ID PART NO DESCRIPTION ID PART NO DESCRIPTION

1 31112165 SCREW TE C/F M8X35 DIN 6921 8G 21 55102714 KNOB 2 31112166 SCREW TE C/F M8X25 DIN 6921 8G 22 55259133 GUARD 45 " 3 31112167 SCREW TE C/F M8X30 DIN 6921 8G 23 55259134 GUARD 53 " 4 31112171 SCREW TE C/F M8X16 DIN 6921 24 56158741 CENTRAL SPACER 5 31121013 SCREW TBCEI M8X16 DIN 7380 25 56158745 BLADE HOLDER SPACER

6 31152081 SCREW TCEI M8X20 UNI 5931 26 56158749 SKID SHOE 7 31221151 NUT M14X1,5 Tighten to 100 Ft lbs 27 56358704 SLIDE BAR 45 " 8 31241085 SELFLOCK NUT M8 6S 28 56358705 SLIDE BAR 53 " 9 31312141 STUD BOLT 29 56358708 BLADE SUPPORT

10 31421083 WASHER M8 30 56358716 BLADE SECTION

11 31421251 DOME WASHER Dome side towards nut 31 56358732 BAR CONNECTION 12 33126513 RIVET TC 6,5X13 32 56358743 BLADE HOLDER GUIDE 13 33126516 RIVET TC 6,5X16 33 56358776 LIMITING BLADE HOLDER 14 33126516 RIVET TC 6,5X16 34 58058661 CONICAL NUT M16X1.5 15 52158700 BLADE COUPLING BF2011 ZINC-COATED 35 58058662 SCREW FOR BLADE CONNECTION

16 52158747 SKID SUPPORT / MOUNT 36 59058593 SPRING LIFTER 17 52158748 NUT RETAINER FOR SKID MOUNT 37 59058764 SPRING W/FINGER 18 52458678 CONNECTION 38 59058770 BLADE ASSEMBLY 45" 23 SECTIONS 19 52458713 DOUBLE FINGER 39 59058771 BLADE ASSEMBLY 53" 27 SECTIONS 20 52458714 SINGLE FINGER 40 59258715 SUPPORT 41 59258746 COMPLETE SKID FOR CUTTING BAR Note ( * ) = New Part / Change Laser Bar Adjustable rev0 10-20-15

Attachments 2013 + Cutter

Bar Adjustable 3 - Dog PTO Laser Bar

w/ Self-Adjusting Tensioners

Bottom Bar Assembly 03.08

ID PART NO DESCRIPTION ID PART NO DESCRIPTION

1 31112165 SCREW TE C/F M8X35 DIN 6921 8G 21 55259133 GUARD 45 " 2 31112166 SCREW TE C/F M8X25 DIN 6921 8G 22 55259134 GUARD 53 " 3 31112167 SCREW TE C/F M8X30 DIN 6921 8G 23 56158741 CENTRAL SPACER 4 31112171 SCREW TE C/F M8X16 DIN 6921 24 56158745 BLADE HOLDER SPACER

5 * 31112171 SCREW TE C/F M8X16 DIN 6921 25 56158749 SKID SHOE

6 31152081 SCREW TCEI M8X20 UNI 5931 26 56358704 SLIDE BAR 45 " 7 31221151 NUT M14X1,5 Tighten to 100 Ft lbs 27 56358705 SLIDE BAR 53 " 8 31241085 SELFLOCK NUT M8 6S 28 56358708 BLADE SUPPORT 9 31312141 STUD BOLT 29 56358716 BLADE SECTION

10 31421251 DOME WASHER Dome side towards nut 30 56358732 BAR CONNECTION

11 33126513 RIVET TC 6,5X13 31 56358743 BLADE HOLDER GUIDE 12 33126516 RIVET TC 6,5X16 32 56358776 LIMITING BLADE HOLDER 13 33126516 RIVET TC 6,5X16 33 58058661 CONICAL NUT M16X1.5 14 52158700 BLADE COUPLING BF2011 ZINC-COATED 34 58058662 SCREW FOR BLADE CONNECTION 15 52158747 SKID SUPPORT / MOUNT 35 59058593 SPRING LIFTER

16 52158748 NUT RETAINER FOR SKID MOUNT 36 59058764 SPRING W/FINGER 17 52458678 CONNECTION 37 59058770 BLADE ASSEMBLY 45" 23 SECTIONS 18 52458713 DOUBLE FINGER 38 59058771 BLADE ASSEMBLY 53" 27 SECTIONS 19 52458714 SINGLE FINGER 39 59258715 SUPPORT 20 55102714 KNOB 40 59258746 COMPLETE SKID FOR CUTTING BAR 41 * 92290984 SKID SET PAIR Note ( * ) = New Part / Change Laser Bar Adjustable rev1 10-20-15

Attachments 2013 + Cutter

Bar Adjustable 3 - Dog PTO Laser Bar

w/ Self-Adjusting Tensioners

Bottom Bar Assembly 03.09

ID PART NO DESCRIPTION ID PART NO DESCRIPTION

1 31112165 SCREW TE C/F M8X35 DIN 6921 8G 22 55259133 GUARD 45 " 2 31112166 SCREW TE C/F M8X25 DIN 6921 8G 23 55259134 GUARD 53 " 3 31112167 SCREW TE C/F M8X30 DIN 6921 8G 24 56158741 CENTRAL SPACER 4 31112171 SCREW TE C/F M8X16 DIN 6921 25 56158745 BLADE HOLDER SPACER 5 31112171 SCREW TE C/F M8X16 DIN 6921 26 56158749 SKID SHOE

6 31152081 SCREW TCEI M8X20 UNI 5931 27 56358704 SLIDE BAR 45 " 7 31221151 NUT M14X1,5 Tighten to 100 Ft lbs 28 56358705 SLIDE BAR 53 " 8 31241085 SELFLOCK NUT M8 6S 29 56358708 BLADE SUPPORT 9 31312141 STUD BOLT 30 56358716 BLADE SECTION

10 31421251 DOME WASHER Dome side towards nut 31 56358732 BAR CONNECTION

11 33126513 RIVET TC 6,5X13 32 56358743 BLADE HOLDER GUIDE 12 33126516 RIVET TC 6,5X16 33 56358776 LIMITING BLADE HOLDER 13 33126516 RIVET TC 6,5X16 34 58058661 CONICAL NUT M16X1.5 14 52158700 BLADE COUPLING BF2011 ZINC-COATED 35 58058662 SCREW FOR BLADE CONNECTION 15 52158747 SKID SUPPORT / MOUNT 36 59058593 SPRING LIFTER

16 52158748 NUT RETAINER FOR SKID MOUNT 37 59058764 SPRING W/FINGER 17 52458678 CONNECTION 38 59058770 BLADE ASSEMBLY 45" 23 SECTIONS 18 52458713 DOUBLE FINGER 39 59058771 BLADE ASSEMBLY 53" 27 SECTIONS 19 52458714 SINGLE FINGER 40 59258715 SUPPORT

20 * 53058751 LASER DECAL 41 59258746 COMPLETE SKID FOR CUTTING BAR

21 55102714 KNOB 42 92290984 SKID SET PAIR Note ( * ) = New Part / Change Laser Bar Adjustable rev2 10-20-15

Attachments 2013 + Cutter

Bar Hood 3 - Dog PTO Torx Oil Bath Control

Serial Number Range 474946 ------------- 04.00

ID PART NO DESCRIPTION ID PART NO DESCRIPTION

1 30010144 SILENT-BLOCK 13 56358563 CONNECTION 2 31111091 SCREW E M6X14 UNI 5739 8G 14 56358643 SPECIAL WASHER 15X20X6 3 31111331 SCREW TE M14X50 UNI5739 8G 15 56359180 CONNECTION 4 31112152 SCREW TE M8X30 UNI 5739 8G 16 58046689 SPECIAL SCREW 5 31241060 HEXAGON SELFLOCK NUT M6 17 58057724 DECAL

6 31241080 HEXAGON SELFLOCK NUT M8 18 58057769 DECAL 7 31241140 SELFLOCK NUT M14 19 58058562 SPECIAL SCREW 8 31423084 SPRING WASHER 8,4 20 59258592 FRONT DEFLECTOR 114 MM 9 31423150 SPRING WASHER 15 21 59258631 FRONT DEFLECTOR 195 MM

10 53048656 DECAL

11 53058850 DECAL 12 55143495 PLUG

Oil Bath Control Hood rev7 10-27-15