VALVESARMATUREN
Edition 8 - Au age 8
2 QUALITY SINCE 1972
IMT ARMATUREN quality starts at the engineering stage, the choice of the raw material and continues through production, testing and packaging. IMT ARMATUREN uses only brass according to DIN EN 12165 and DIN EN 12164. Every valve sees service before it goes into your job because it passes rigorous quality checks to make sure it will perform awlessly. Every valve is pressure tested before it is packaged in rugged boxes with bar coded labels; ideal for inventory control. When you see the name IMT ARMATUREN on a valve, you are assured trouble-free service.IMT ARMATUREN offers a full line of industrial, plumbing and heating valves.
Forging brass according to DIN EN 12165 / Press-Messinglegierung gemss DIN EN 12165
DIN EN Element Cu PB Sn Fe Ni Al OthersAndere Zn
CuZn40Pb2 CW617N min.max.
57,059,0
1,62,5
-0,3
-0,3
-0,3
-0,05
-0,2
-rest
Machining brass according to DIN EN 12164 / Messing-Drehteile gemss DIN EN 12164
DIN EN Element Cu PB Sn Fe Ni Al OthersAndere Zn
CuZn40Pb2 CW617N min.max.
57,059,0
1,62,5
-0,3
-0,3
-0,3
-0,05
-0,2
-rest
Die Qualitt von IMT ARMATUREN wird bereits bei der Entwicklung neuer Produkte geplant; sie zieht sich durch die Konstruktion, Auswahl der Rohstoffe, die gesamte Produktion, bis hin zur Verpackung und den Versand.IMT ARMATUREN verwendet nur Messing nach DIN EN 12165 und DIN EN 12164.Bevor IMT Armaturen vom Kunden eingebaut werden, durchlaufen sie verschiedene Prfstationen; vor dem endgltigen Verpacken werden sie Stck fr Stck druckgeprft und in mit Barcodes versehene Kartons verpackt. Ideal fr die Lagerkontrolle.Also, wenn Sie den Namen IMT ARMATUREN lesen, haben Sie die Gewissheit, dass Sie Armaturen einbauen, die problemlos funktionieren.IMT ARMATUREN fhrt ein grosses Programm an Industrie-, Heizungs- und Sanitrarmaturen.
1 inch = 25,4 mm1 psi = 0,0689 bar; 1 bar = 14,5 psi
1C = ((1C x 1,8) + 32)F1 kg = 2,205 lb; 1 lb = 0,454 kg
APPROVALS ZULASSUNGEN
ROSTECHNADZOR(GGTN)
3QUALITY SINCE 1972
SWITZERLAND IMT ARMATUREN AGSonnenstr. 8-10CH - 9434 Au / St.GallenTel. +41/71/744.39.71 - Fax +41/71/744.44.21www.imt-ch.com - [email protected]
ITALYIMT ARMATUREN S.R.L.Via delle Fontane, 66I - 13011 Borgosesia (VC)Tel. +39/0163/204.555 - Fax +39/0163/204.556www.imt-ch.com - [email protected]
Italy - ItalienSwitzerland - Schweiz
Illustrations are actual representations of a certain size of each line of products but do not necessarily represent all sizes in all details. The designs, materials, and/or speci cations shown are subject to change without notice due to IMT ARMATURENs continuing program of improvement.This catalogue replaces all previous catalogues and brochures. All rights reserved. This publication is fully protected by copyright and nothing that appears in it may be reproduced, either wholly or in part, without special permission. See the actual Terms and Conditions on page 72.
Die Illustrierungen sind aktuelle Darstellungen von einer bestimmten Dimension jeder Produktreihe; sie reprsentieren nicht alle Grssen im Detail. Das Design, Material und die Masse sind unverbindlich. IMT ARMATUREN behlt sich vor, nderungen ohne Absprache vorzunehmen.Mit Erscheinen dieses Kataloges werden alle vorherigen Kataloge und Prospekte ungltig. Nachdruck und fotomechanische Wiedergabe, auch auszugsweise, bedrfen ausdrcklicher Genehmigung der Firma IMT ARMATUREN AG. Die geltenden IMT ARMATUREN Verkaufs- und Lieferbedingungen nden Sie auf Seite 73.
SALES NETWORKVERTRIEBSNETZ
IMT ARMATUREN is registered to ISO 9001:2008 quality standards.IMT ARMATUREN ist nach ISO 9001:2008 zerti ziert.
4 QUALITY SINCE 1972
Series Index Page576 FFL 45
581 52
583 48
587 53
591 FFL 45
591FFL MT 45
593 38
594 42-44
594+030 58
595 39
695 36
695A 37
701 64
702 64
3000.TK 12
REP.SET.KH 62
Series Index Page005 62
008 62
009 62
010 62
011 61
012 60
014 61
015 60
016 60
017 60
018 60
019 61
020 61
021 61
030 57-58
100 29
101 19
101S 17
105 59
108 13
109 13
115 28
116 26
117 27
120 24
120L 25
121 23
121S 16
123 20
124 14
125 18
125S 15
126 21
126K 22
129 29
130 30
131 31
132 30
133 31
150 70
155 70
235 34-35
236 34-35
237 34-35
255 54-55
260 32
265 54-55
275 54-55
279 32
285 54-55
295 54-55
300 8
301 6
302 9
303K 6
305K 7
306 10
307 11
491 49-51
492 46-47
500 65
510 65
515 33
516 33
517 33
542 63
543 56
543+030 58
550 66-67
551 66-67
553-554 68
570 69
571 69Index
INH
ALT
SVER
ZEIC
HN
ISA
B
C
E
F
G
H
IK
O
P
R
S
T
ML
Product Index PageAccessorier for Ball Valves 60-62
Actuator for Ball Valves 57-58
Air Separator "Airterminator" 14
Aqua Clean Backwash Filter 66-67
Automatic Air Vents 15-29
Automatic Air Vents for Solar Application 15-17
Back ow Preventer Assembly 6
Back ow Preventer for Completion of an Extraction Valve/Bibcock 9
Back ow Preventer for Completion of Water Columns 11
Back ow Preventer in Stainless Steel 10
Back ow Preventers 6-12
Ball Valve to service and test Expansion Tanks 59
Ball Valve with Drain 51
Ball Valve with Hose Union 51
Ball Valves 36-56
Ball Valves for Gas and Potable Water 42-44, 46-48
Ball Valves for Potable Water 42-44, 46-48
Ball Valves with Electric Actuator 57-58
Bibcock 53
Boiler Filling and Drain Valves 54-55
Boiler Safety Groups 13
Check Valves 34-35
Colombo Air Vents 26-27
Concealed Ball Valve 64
Elite Air Vent 18
Elite Solar Air Vent 15
Excellent Air Vents 21-22
Extraction Valve with integrated Back ow Preventer 8
Filling Assembly 7
Filling Unit 32
Flanged Ball Valve 63
Flanged Pressure Reducing Valve 33
Flanged Shut-off Valves 45
Gas Ball Valves 36-39
Gas Safety Shutt-off Valve 36-37
Handles 60-62
High Pressure Air Vent 20
Insulation for Ball Valves 62
Kombi Air Vent 29
Locking Handle 62
Manual Backwash Filter 66-67
Manual Filters for cold and hot water 68
Memory Stop 62
Micro Air Vents 24-25
Mini Ball Valve 52
Minival Air Vent 23
Minival Solar Air Vent 16
Mixing Valve 65
Multilogo 40-41
Original Air Vent 19
Original Solar Air Vent 17
Pressure Gauge 29
Pressure Reducing Valves 33
Pressure Relief Valves 30-31
Radiator Air Vents 26-28
Radiator Valves 70
Repair Set for Ball Valves 62
Stem Extension 62
Strainer 69
Test Kit for Back ow Preventers 12
Thermal Safety Valve 32
Thermostatic Mixing Valve 65
Three-Way Ball Valve 56
Chemical Resistance for Ball Valves 71
Terms and Conditions 72
5QUALITY SINCE 1972
Artikel-Verzeichnis Seite576 FFL 45
581 52
583 48
587 53
591 FFL 45
591FFL MT 45
593 38
594 42-44
594+030 58
595 39
695 36
695A 37
701 64
702 64
3000.TK 12
REP.SET.KH 62
Index
INH
ALT
SVER
ZEIC
HN
IS
Artikel-Verzeichnis Seite005 62
008 62
009 62
010 62
011 61
012 60
014 61
015 60
016 60
017 60
018 60
019 61
020 61
021 61
030 57-58
100 29
101 19
101S 17
105 59
108 13
109 13
115 28
116 26
117 27
120 24
120L 25
121 23
121S 16
123 20
124 14
125 18
125S 15
126 21
126K 22
129 29
130 30
131 31
132 30
133 31
150 70
155 70
235 34-35
236 34-35
237 34-35
255 54-55
260 32
265 54-55
275 54-55
279 32
285 54-55
295 54-55
300 8
301 6
302 9
303K 6
305K 7
306 10
307 11
491 49-51
492 46-47
500 65
510 65
515 33
516 33
517 33
542 63
543 56
543+030 58
550 66-67
551 66-67
553-554 68
570 69
571 69
A
BC
E
F
G
H
IK
O
PR
S
T
ML
Produkt-Verzeichnis SeiteAbschliessbarer Griff 62
Antrieb fr Kugelhahn 57-58
Aqua-Clean Rckspl lter 66-67
Auslaufkugelhahn 53
Brauchwassermischer 65
Colombo Schnellentlfter 26-27
Drehbegrenzer 62
Dreiwege-Kugelhahn 56
Druckminderer 33
Elite Schnellentlfter 18
Elite Solar Schnellentlfter 15
Entnahmearmatur mit integriertem Systemtrenner 8
Excellent Schnellentlfter 21-22
Flanschdruckminderer 33
Flanschkugelhahn 63
Fllgruppe 32
Gasanschluss-Kugelhahn 36-37
Gaskugelhhne 36-39
Griffe 60-62
Heizkrper Schnellentlfter 26-28
Heizkrper Ventile 70
Hochdruck- Schnellentlfter 20
Isolierung fr Kugelhhne 62
Kappenventil 59
Kesselfll- und Entleerungshhne (KFE) 54-55
Kesselsicherheitsgruppen 13
Kombi Schnellentlfter 29
Kugelhahn mit elektrischem Antrieb 57-58
Kugelhahn mit Entleerungshhnchen 51
Kugelhahn mit berwurfmutter und Tlle 51
Kugelhhne 36-56
Kugelhhne fr Gas und Trinkwasser 42-44, 46-48
Kugelhhne fr Trinkwasser 42-44, 46-48
Luftabscheider "Airterminator" 14
Manometer 29
Manuelle Filter fr Kalt- und Heisswasser 68
Manuelle Rckspl lter 66-67
Membransicherheitsventile 30-31
Micro Schnellentlfter 24-25
Mini-Kugelhahn 52
Minival Schnellentlfter 23
Minival Solar Schnellentlfter 16
Multilogo 40-41
Nachfllkombination 7
Original Schnellentlfter 19
Original Solar Schnellentlfter 17
Pumpen anschkugelhhne 45
Reparaturset fr Kugelhhne 62
Rckschlagventile 34-35
Schmutzfnger 69
Schnellentlfter 15-29
Schnellentlfter fr Solar Anwendungen 15-17
Spindelverlngerung 62
Systemtrenner 6-12
Systemtrenner aus Edelstahl 10
Systemtrenner zum Nachrsten einer Entnahmearmatur 9
Systemtrenner zur Nachrstung von Standrohren 11
Systemtrennerkombination 6
Test Kit fr Systemtrenner 12
Thermische Ablaufsicherung 32
Thermostatischer Brauchwassermischer 65
Unterputz-Kugelhahn 64
Zuberhr fr Kugelhhne 60-62
Bestndigkeitsliste fr Kugelhhne 71
Allgemeine Verkaufs- und Lieferbedingungen 73
D
N
UZ
6 QUALITY SINCE 1972
303K Back ow Preventer Assembly Type BASystemtrennerkombination Typ BA
Systemtrennerkombination Typ BA nach dem Dreikammer - System Gefahrenklasse 4DVGW zerti ziertbestehend aus:Systemtrenner Typ BA Art. 301Prfhhnen Art. 581 undWartungsabsperrungen Art. 583
Nenndruck PN 10Max. Temperatur 65Ckurzzeitig 80C Medium: Wasser
Pressmessing gelbPrfhhne aus Stangenmaterial verchromt
Ausfhrungen: Art. 30304K 1/2Art. 30306K 3/4
Reduced Pressure Zone Principle Back ow Preventer AssemblyType BA - Class of risk 4DVGW certi edConsisting of:Back ow Preventer Type BA Fig. 301Test Cocks Fig. 581 andShutoff Valves Fig. 583
Structural Pressure PN 10 (145 psi)Temperature Rating max. 65C (149F)Short peaks max. 80C (176F)Fluid: water
Forged Brass BodyChrome Plated Test Cocks
Available in:Fig. 30304K 1/2Fig. 30306K 3/4
1 Cu Zn 40 Pb 2 DIN EN 12165
2 Cu Zn 40 Pb 2 DIN EN 12165
3 POM
4 EPDM 70 Shore
5 EPDM 70 Shore
6 EPDM 70 Shore
7 POM
8 Cu Zn 39 Pb 3 DIN EN 12164
9 FASIT
10 POM
11 FASIT
12 Cu Zn 40 Pb 2 DIN EN 12165
13 Cu Zn 40 Pb 2 DIN EN 12165
G L D H1 H2 SW1/2 214 25 70 80 263/4 220 25 70 80 32
G L L0 H1 H2 D1/2 MM 144 89 39 80 253/4 MM 156 95 39 80 25
Dimensions in mmMasse in mm
Dimensions in mmMasse in mm
For Test Cocks Fig. 581 see page 52 Fr Prfhhne Art. 581 siehe Seite 52
For Shutoff Valves Fig. 583 see page 48Fr Wartungsabsperrungen Art. 583 siehe Seite 48
Back
ow
Pre
vente
rs S
YSTE
MTR
ENN
ER 301
7QUALITY SINCE 1972
305K Filling Assembly Type BANachfllkombination Typ BA
Nachfllkombination nach dem Dreikammer - SystemFllarmatur kombiniert mit Systemtrenner Typ BA Gefahrenklasse 4DVGW zerti ziert
Kompakte Ausfhrungbestehend aus:Systemtrenner Typ BA Art. 301Fllgruppe Art. 260Manometer mit Anschluss Art. 100Prfhhnen Art. 581 undWartungsabsperrungen Art. 583
Nenndruck PN 10Max. Temperatur 65Ckurzzeitig 80C Medium: Wasser
Pressmessing gelbPrfhhne aus Stangenmaterial verchromt
Ausfhrungen: Art. 30504K 1/2Art. 30506K 3/4
Reduced Pressure Zone Filling AssemblyFilling Group combined with Back ow Preventer Type BA Class of risk 4DVGW certi ed
Compact DesignConsisting of:Back ow Preventer Type BA Fig. 301Filling Group Fig. 260Pressure Gauge with connection thread Fig. 100Test Cocks Fig. 581 andShutoff Valves Fig. 583
Structural Pressure PN 10 (145 psi)Temperature Rating max. 65C (149F)Short peaks max. 80C (176F)Fluid: water
Forged Brass BodyChrome Plated Test Cocks
Available in:Fig. 30504K 1/2Fig. 30506K 3/4
G L D H1 H2 SW1/2 258 25 93 80 263/4 264 25 93 80 32
Dimensions in mmMasse in mm
For Back ow Preventer Fig. 301 see page 6 Fr Systemtrenner Art. 301 siehe Seite 6
For Filling Group Fig. 260 see page 32Fr Fllgruppe Art. 260 siehe Seite 32
For Pressure Gauge Fig. 100 see page 29Fr Manometer Art. 100 siehe Seite 29
For Test Cocks Fig. 581 see page 52 Fr Prfhhne Art. 581 siehe Seite 52
For Shutoff Valves Fig. 583 see page 48Fr Wartungsabsperrungen Art. 583 siehe Seite 48
8 QUALITY SINCE 1972
300 Extraction Valve with integrated Back ow Preventer Type BAEntnahmearmatur mit integriertem Systemtrenner Typ BA
Armatur zum Einbau ber einem Entwsserungsgegenstand oder zum Einbau im Freien (Gartenventil) konzipiertBestehend aus einem eingangsseitigen Kugelhahn und einem nach-geschalteten Systemtrenner Typ BA nach dem Dreikammer - SystemGefahrenklasse 4
Pressmessing verchromtVerchromte KugelMit Multilogo Griff
Nenndruck PN 10Max. Temperatur 65Ckurzzeitig 80C Medium: Wasser
Ausfhrungen: Art. 30004 1/2 (G und G1 siehe oben)Art. 30006 3/4 (G und G1 siehe oben)Art. 30008 3/4 (G und G1 siehe oben)
Conceived to be used as a garden valve or ll valve for heating systemsConsisting of a one way Ball Valve and a Reduced Pressure Zone Back ow Preventer Type BA Class of risk 4
Chrome Plated Brass BodyChrome Plated BallWith Multilogo Handle
Structural Pressure PN 10 (145 psi)Temperature Rating max. 65C (149F)Short peaks max. 80C (176F)Fluid: water
Available in:Fig. 30004 1/2 (G and G1 see above)Fig. 30006 3/4 (G and G1 see above)Fig. 30008 3/4 (G and G1 see above)
1 UNI EN 12165 - CW617N
2 UNI EN 12165 - CW617N
3 Stainless Steel - Stahl AISI 302
4 NBR 70 Shore
5 PTFE
6 UNI EN 12164 - CW614N
7 Polypropylene - Polypropylen
8 UNI EN 12164 - CW614N
9 Polypropylene - Polypropylen
10 Polypropylene - Polypropylen
11 EPDM 70 Shore
12 POM
13 EPDM 70 Shore
14 UNI EN 12165 - CW617N
15 EPDM 70 Shore
16 Aluminium Al Si 12Cu 2 Fe
17 POM
G G1 L L1 L2 L3 H H1 H21/2 3/4 108 75 58 100 120 40 803/4 3/4 108 75 58 100 120 40 803/4 1 108 75 58 100 123 40 83
Dimensions in mmMasse in mm
Back
ow
Pre
vente
rs S
YSTE
MTR
ENN
ER
9QUALITY SINCE 1972
302 Back ow Preventer Type BA for Completion of an Extraction Valve/BibcockSystemtrenner Typ BA zum Nachrsten einer Entnahmearmatur
Dreikammer - System PrinzipGefahrenklasse 4Zum nachtrglichen Anbau an eine Entnahmearmatur mit Schlauchanschluss konzipiertSicherungsschraube und Schutzkappe gegen ManipulationenDVGW Zerti zierung fr die Verwendung an Standrohren
Pressmessing verchromt
Nenndruck PN 10Max. Temperatur 65Ckurzzeitig 80C Medium: Wasser
Ausfhrungen: Art. 30204 1/2 (G und G1 siehe oben)Art. 30206 3/4 (G und G1 siehe oben)Art. 30208 3/4 (G und G1 siehe oben)
Reduced Pressure Zone PrincipleClass of risk 4Designed for application on extraction valves/bib cocks with hose connectionSafety screw and protection cap against tamperingDVGW certi cation for the application on water columns
Chrome Plated Brass Body
Structural Pressure PN 10 (145 psi)Temperature Rating max. 65C (149F)Short peaks max. 80C (176F)Fluid: water
Available in:Fig. 30204 1/2 (G and G1 see above)Fig. 30206 3/4 (G and G1 see above)Fig. 30208 3/4 (G and G1 see above)
1 UNI EN 12165 - CW617N
2 UNI EN 12164 - CW614N
3 EPDM 70 Shore
4 POM
5 EPDM 70 Shore
6 UNI EN 12165 - CW617N
7 POM
8 FASIT
9 UNI EN 12164 - CW614N
10 EPDM 70 Shore
DN G G1 H L1/2 3/4 3/4 84 753/4 1 3/4 84 753/4 1 1 87 75
Dimensions in mmMasse in mm
10 QUALITY SINCE 1972
306 Back ow Preventer Type BASystemtrenner Typ BA
Systemtrenner Typ BA nach dem Dreikammer - System Gefahrenklasse 4 MetallbalggesteuertFr Chemische- und Pharma-Industrie Fr den Einsatz im VE-Wasserbereich besonders geeignet, da buntmetallfrei
EdelstahlkrperPrfhhne aus Edelstahl
Nenndruck PN 10Max. Temperatur 65Ckurzzeitig 80C Medium: Wasser
Ausfhrungen: Mit GewindenMit Anschweissenden
Reduced Pressure Zone Back ow Preventer Type BAClass of risk 4 With bellow actuated cartridge For pharma- and chemical industrySpecially foreseen for the application in demineralised water systems, because non ferrous-metal free
Stainless Steel BodyStainless Steel Test Cocks
Structural Pressure PN 10 (145 psi)Temperature Rating max. 65C (149F)Short peaks max. 80C (176F)Fluid: water
Available in:with threaded endswith welding ends
DN L I R d H h A F G (kg)15 176 74 21 16 112 25 50 68 2.0020 176 74 27 22 112 25 50 68 2.0025 229 92 34 30 117 25 50 88 3.1332 229 92 42 37 117 25 50 88 3.2040 284 111 48 42 121 25 50 104 5.9050 303 112 57 51 121 25 50 104 6.20
Dimensions in mmMasse in mm
1 Stainless Steel - Edelstahl 1.4301
2 EPDM
3 POM
4 POM
Back
ow
Pre
vente
rs S
YSTE
MTR
ENN
ER
11QUALITY SINCE 1972
307 Back ow Preventer Type BASystemtrenner Typ BA
Systemtrenner Typ BA nach dem Dreikammer - System Gefahrenklasse 4DVGW zerti ziertzur Nachrstung vorhandener StandrohreDN 40 und DN 50
Krper: EdelstahlAnschlsse: Messing aus Stangenmaterial
Nenndruck PN 10Max. Temperatur 65Ckurzzeitig 80C Medium: Wasser
Ausfhrungen: Art. 307 FF Innen- x InnengewindeArt. 307FM Innen- x AussengewindeArt. 307MF Aussen- x InnengewindeArt. 307MM Aussen- x Aussengewinde
Reduced Pressure Zone Back ow Preventer Type BAClass of Risk 4DVGW certi edfor completion of existing water columnsDN 40 and DN 50
Body: Stailess SteelConnections: Brass from barstock
Structural Pressure PN 10 (145 psi)Temperature Rating max. 65C (149F)Short peaks max. 80C (176F)Fluid: water
Available in:Fig. 307 FF Female EndsFig. 307FM Female/Male EndsFig. 307MF Male/Female EndsFig. 307MM Male Ends
Female EndsInnen- x Innengewinde
Female/Male EndsInnen- x Aussengewinde
Male EndsAussen- x Aussengewinde
Male/Female EndsAussen- x Innengewinde
307 FF
307 FM
307 MM
307 MF
Dimensions in mmMasse in mm
Dimensions in mmMasse in mm
Dimensions in mmMasse in mm
Dimensions in mmMasse in mm
A B1 1/2 1 1/2
2 21 1/2 2
2 1 1/2
A B1 1/2 1 1/2
2 21 1/2 2
2 1 1/2
A B1 1/2 1 1/2
2 21 1/2 2
2 1 1/2
A B1 1/2 1 1/2
2 21 1/2 2
2 1 1/2
1 Cu Zn 40 Pb2 DIN EN 12165
2 POM
3 POM
4 POM
5 POM
6 Stainless Steel Edelstahl 1.4301
7 Cu Zn 39 Pb3 DIN EN 12164
8 Copper Kupfer
9 EPDM
10 EPDM
11 EPDM
12 EPDM
13 EPDM
14 NBR
15 POM
16 POM
12 QUALITY SINCE 1972
3000.TK Test Kit for Back ow Preventers Test-Kit fr Systemtrenner
Dieses Test Kit ist fr das Prfen der richtigen Funktionalitt von IMT Systemtrennern, die mit Eingangsdruck bis 10 bar und P max. 1,5 bar eingesetzt werden.
This Test Kit is suitable for testing the correct function of IMTback ow preventers, working with inlet pressure till 10 bar and P max. 1,5 barAvailable in a practical carrying case
Gauge type: Diaphragm differential pressureCase diameter: 100 mmMax. static pressure: 25 barPressure range: 0 / 16 barOverpressure safety: up to 25 bar on both sides
Accuracy class: 2,5Body: Stainless steel, with bayonet type bezelMeasuring spring: Stainless steelDiaphragm: Viton
Mechanism: Brass
Hose length: 2 hoses x 1 m with connection 3/8 Connections and delivered separated in the case
Case: Plastic
Anzeigetyp: Membrane DifferenzialdruckGehusedurchmesser: 100 mmMax. statischer Druck: 25 barMessbereich: 0 / 16 barberdrucksicherheit:: beidseitig bis 25 bar
Genauigkeitsklasse: 2,5Gehuse: Edelstahl, mit BajonettringMessglied Druckfeder: EdelstahlMembrane: Viton
Zeigerwerk: Messing
Lnge der Flexrohre: 2 Rohre x 1 m mit Anschluss 3/8Anschlsse und separat im Koffer mitgeliefert
Koffer: Kunststoff
Back
ow
Pre
vente
rs S
YSTE
MTR
ENN
ER
13QUALITY SINCE 1972
Boile
r Sa
fety
Gro
ups
KES
SELS
ICH
ERH
EITS
GRU
PPEN
108
109
Boiler Safety Group KSGKesselsicherheitsgruppe KSG
Boiler Safety Group Compact KSGKesselsicherheitsgruppe Kompakt KSG
Bestehend aus: Membransicherheitsventil Art. 13104 (TV geprft)Automatischer Schnellentlfter MINIVAL Art. 12103Manometer Art. 100Absperrventil IsolierungSelbstdichtendem Gewinde und Kontermutter
Ansprechdruck 3 barMaximale Temperatur 110C Wasser (ohne Dampf)Messing gelb
Ausfhrungen: Art. 10808 1
Bestehend aus: Integriertes Membransicherheitsventil (TV geprft)Integrierter Automatischer Schnellentlfter Manometer Art. 100Isolierung
Ansprechdruck 2,5 und 3 barMaximale Temperatur 110C Wasser (ohne Dampf)Messing gelb
Ausfhrungen: Art. 10908 1
Consisting of:Pressure Relief Valve Fig. 13104 (TV approved)Automatic Air Vent MINIVAL Fig.12103Pressure Gauge Fig. 100StopvalveInsulation CoverSelftightening Thread and Nut
Pressure relief setting 3 bar (43,5 psi)Temperature Rating max. 110C (230F) water (no steam)Brass Body
Available in: Fig. 10808 1
Consisting of: Integrated Pressure Relief Valve (TV approved)Integrated Automatic Air Vent Pressure Gauge Fig. 100Insulation Cover
Pressure Relief Setting 2,5 and 3 bar (36,3 and 43,5 psi)Temperature Rating max. 110C (230F) water (no steam)Brass Body
Available in: Fig. 10908 1
G G1 L SW H1 3/4 93 38 172
Dimensions in mmMasse in mm
Dimensions in mmMasse in mm
Rp Rp1 L L1 L2 L3 (L4) H1 3/4 106 21 18 51 178 109
14 QUALITY SINCE 1972
124 Air Separator Air TerminatorLuftabscheider Air TerminatorA
ir v
ents
SC
HN
ELLE
NTL
FT
ER
Luftabscheider komplett mit:Automatischem Schnellentlfter Excellent, Art. 126 (siehe Seite 21)Verschlussstopfen Nenndruck 12 barArbeitsdruck 6 bar - entsprechend dem eingebauten Schnellentlfter Maximale Temperatur 110C Wasser (ohne Dampf)Fr Solaranwendungen empfehlen wir den Entlfter Art. 125S zu verwenden, fr Sonderanwendungen den Hochdruck-Entlfter Art. 123, der fr einen Arbeitsdruck von 11 bar geeignet ist.Medium: Wasser und Wasserglykolgemisch (max. 50%) Messing gelbGewinde nach ISO 228
Ausfhrungen: Art. 12406 3/4Art. 12408 1Art. 12410 1 1/4Auf Anfrage KFE-Hahn anstatt Verschlussstopfen unten
Air Separator complete with:Automatic Air Vent Excellent, Fig. 126 (see page 21)Blind cap Structural Pressure 12 bar (174 psi)Working Pressure 6 bar (87 psi) - according to the used air ventFor solar systems we recommend to use the air vent ELITE SOLAR 125S, for higher pressure the air vent Art. 123 which is suitable for a working pressure of 11 bar.Fluid: Water and water/glycol mixtures (max. 50%)
Brass body Threaded Ends according to ISO 228
Available in:Fig. 12406 3/4Fig. 12408 1Fig. 12410 1 1/4Upon request drain valve instead of blind cap at the bottom
1 Cu Zn 40 Pb 2 - DIN EN 12165
2 Cu Zn 40 Pb 2 - DIN EN 12165
3 Stainless Steel - Edelstahl AISI 302
4 PTFE
5 Cu Zn 40 Pb 2 - DIN EN 12165
6 Cu Zn 40 Pb 2 - DIN EN 12165
7 Polyacetalic - Azetal Harz POM
8 Norylic Resin - Norylharz
9 NBR 50 Shore
10 Stainless Steel - Edelstahl AISI 302
11 NBR 70 Shore
12 Polypropylene - Polypropylen
13 Polypropylene - Polypropylen
14 Cu Zn 39 Pb 3 - DIN EN 12164
15 Polypropylene - Polypropylen
16 NBR 70 Shore
17 NBR 70 Shore
18 Stainless Steel - Edelstahl AISI 302
19 PTFE
20 Cu Zn 39 Pb 3 - DIN EN 12164
21 NBR 70 Shore
G D L L1 G1 G2 H H1 H2 SW3/4 83 170 18 1/2 1/2 213 146 67 38
1 83 151 16,5 1/2 1/2 213 146 67 381 1/4 83 151 16 1/2 1/2 213 146 67 47
Dimensions in mmMasse in mm
15QUALITY SINCE 1972
125S Automatic Air Vent Elite Solar with StopvalveAutomatischer Schnellentlfter Elite Solar mit Absperrventil
Stopvalve for Elite Solar Figure 111 Absperrventil zu Elite Solar Artikel 111
Nenndruck 18 barArbeitsdruck 10 barMaximale Temperatur 150C Wasser (ohne Dampf)Drehbarer DeckelMessing gelb
Medium: Wasser
Ausfhrungen: Art. 125S01 1/8 NPTArt. 125S02 1/4 NPTArt. 125S03 3/8 ISO 228Art. 125S04 1/2 ISO 228
Ausfhrungen: Art. 11153HT 3/8 x 3/8 mit Hochtemperatur-Kunstoff-EinsatzArt. 11155HT 3/8 x 1/2 mit Hochtemperatur-Kunstoff-EinsatzArt. 11164HT 1/2 x 1/2 mit Messing Einsatz
Structural Pressure 18 bar (261 psi)Working Pressure 10 bar (145 psi)Temperature Rating max. 150C (302F) water (no steam)Rotating CapBrass Body and Cap
Fluid: Water
Available in: Fig. 125S01 1/8 NPTFig. 125S02 1/4 NPTFig. 125S03 3/8 ISO 228Fig. 125S04 1/2 ISO 228
Available in:Fig. 11153HT 3/8 x 3/8 with high temperature Plastic InsertFig. 11155HT 3/8 x 1/2 with high temperature Plastic InsertFig. 11164HT 1/2 x 1/2 with Brass Insert
1 Cu Zn 40 Pb 2 - DIN EN 12165
2 Cu Zn 40 Pb 2 - DIN EN 12165
3 TPX
4 Cu Zn 39 Pb 3 - DIN EN 12164
5 Cu Zn 39 Pb 3 - DIN EN 12164
6 Stainlees Steel - Edelstahl AISI 302
7 Cu Zn 39 Pb 3 - DIN EN 12164
8 EPDM 70 Shore
9 EPDM 70 Shore
10 EPDM 70 Shore
G A L H H1 B SW 1/8 75 48 98 87 10,5 231/4 75 48 98 87 10,5 233/8 75 48 98 87 10,5 231/2 75 48 98 87 10,5 27
Dimensions in mmMasse in mm
1 1 BODY / KRPER
2 2 FLOAT / SCHWIMMER
3 O RING / O-RING
4 FLOAT LEVER / SCHWIMMERARM
5 GASKET / DICHTUNG
6 SPRING / FEDER
7 NUT / MUTTER
8 CAP / DECKEL
9 VENTING CONNECTIONENTLFTUNGSVERSCHRAUBUNG
10 SMALL CAP / KPPCHEN
16 QUALITY SINCE 1972
121S Automatic High Capacity Air Vent Minival Solar with StopvalveAutomatischer Schnellentlfter Minival Solar mit hoher Entlftungskapazitt, mit Absperrventil
Absperrventil zu Minival Solar Artikel 111Stopvalve for Minival Solar Figure 111
Air
ven
ts S
CH
NEL
LEN
TL
FTER
Nenndruck 10 barArbeitsdruck 6 barMaximale Temperatur 150C Wasser (ohne Dampf)Schnellentlfter in GanzmetallausfhrungMessing gelbMedium: Wasser
Ausfhrungen: Art. 121S01 1/8 NPTArt. 121S02 1/4 NPTArt. 121S03 3/8 ISO 228Art. 121S04 1/2 ISO 228
Ausfhrungen: Art. 11153HT 3/8 x 3/8 mit Hochtemperatur-Kunstoff-EinsatzArt. 11155HT 3/8 x 1/2 mit Hochtemperatur-Kunstoff-EinsatzArt. 11164HT 1/2 x 1/2 mit Messing Einsatz
Structural Pressure 10 bar ( 145 psi)Working Pressure 6 bar (87 psi)Temperature Rating max. 150C (302F) water (no steam)Air Vent in Full Metal DesignBrass Body and CapFluid: Water
Available in:Fig. 121S01 1/8 NPTFig. 121S02 1/4 NPTFig. 121S03 3/8 ISO 228 Fig. 121S04 1/2 ISO 228
Available in:Fig. 11153HT 3/8 x 3/8 with high temperature Plastic InsertFig. 11155HT 3/8 x 1/2 with high temperature Plastic InsertFig. 11164HT 1/2 x 1/2 with Brass Insert
1 Cu Zn 40 Pb 2 - DIN EN 12165
2 TPX
3 Questra
4 Stainless Steel - Edelstahl AISI 302
5 EPDM 60 Shore
6 EPDM 70 Shore
7 Questra
8 Cu Zn 40 Pb 2 - DIN EN 12165
9 Cu Zn 39 Pb 3 - DIN EN 12164
G B SW H A1/8 10,5 23 83 471/4 10,5 23 83 473/8 10,5 23 83 471/2 10,5 27 83 47
Dimensions in mmMasse in mm
9
8
5
6
4
7
3
2
1
1 BODY / KRPER
2 FLOAT / SCHWIMMER
3 FLOAT LEVER / SCHWIMMERARM
4 SPRING / FEDER
5 GASKET / DICHTUNG
6 O RING / O-RING
7 PLASTIC CAP / KUNSTSTOFFDECKEL
8 CAP / DECKEL
9 SMALL CAP / KPPCHEN
17QUALITY SINCE 1972
101S Automatic Air Vent Original Solar with StopvalveAutomatischer Schnellentlfter Original Solar mit Absperrventil
Absperrventil zu Original Solar Artikel 111Stopvalve for Original Solar Figure 111
Nenndruck 12 barArbeitsdruck 4 barMaximale Temperatur 180C Wasser (ohne Dampf)Verchromter Schnellentlfter in GanzmetallausfhrungMedium: Wasser
Ausfhrungen: Art. 101S03 3/8 ISO 228Art. 101S04 1/2 ISO 228
Ausfhrungen: Art. 11153HTC 3/8 x 3/8 mit Hochtemperatur-Kunstoff-EinsatzArt. 11155HTC 3/8 x 1/2 mit Hochtemperatur-Kunstoff-EinsatzArt. 11164HTC 1/2 x 1/2 mit Messing Einsatz
Structural Pressure 12 bar (174 psi)Working Pressure 4 (58 psi)Temperature Rating max. 180C (356F) water (no steam)Chrome Plated Air Vent in Full Metal DesignFluid: Water
Available in:Fig. 101S03 3/8 ISO 228Fig. 101S04 1/2 ISO 228
Available in:Fig. 11153HTC 3/8 x 3/8 with high temperature Plastic InsertFig. 11155HTC 3/8 x 1/2 with high temperature Plastic InsertFig. 11164HTC 1/2 x 1/2 with Brass Insert
1 Cu Zn 40 Pb 2 - DIN EN 12165
2 TPX
3 Stainless Steel - Edelstahl AISI 304
4 Cu Zn 39 Pb 3 - DIN EN 12164
5 Stainless Steel - Edelstahl AISI 304
6 Viton
7 Viton
8 Cu Zn 40 Pb 2 - DIN EN 12165
9 Stainless Steel - Edelstahl AISI 302
10 Questra
11 C u Zn 39 Pb 3 - DIN EN 12164
G B SW H A3/8 10,5 23 84 48,51/2 10,5 27 82 48,5
Dimensions in mmMasse in mm
11
10
9
8
5
6
4
7
3
2
1
1 BODY / KRPER
2 FLOAT / SCHWIMMER
3 FLOAT LEVER / SCHWIMMERARM
4 SMALL STEM / ACHSE
5 LEVER SUPPORT / SCHWIMMERARMHALTER
6 O RING / O-RING
7 O RING / O-RING
8 CAP / DECKEL
9 SPRING / FEDER
10 STEM STOP / MUTTER
11 SMALL CAP / KPPCHEN
18 QUALITY SINCE 1972
125 Automatic Air Vent Elite with StopvalveAutomatischer Schnellentlfter Elite mit Absperrventil
Absperrventil zu Elite Artikel 111Stopvalve for Elite Figure 111
Air
ven
ts S
CH
NEL
LEN
TL
FTER
Nenndruck 12 barArbeitsdruck 6 barMaximale Temperatur 110C Wasser (ohne Dampf)Drehbarer DeckelMessing gelbMedium: Wasser
Ausfhrungen: Art. 12501 1/8 NPTArt. 12502 1/4 NPTArt. 12503 3/8 ISO 228Art. 12504 1/2 ISO 228
Ausfhrungen: Art. 11153 3/8 x 3/8 mit Kunststoff-EinsatzArt. 11164 1/2 x 1/2 mit Messing-EinsatzArt. 11155 3/8 x 1/2 mit Kunststoff-EinsatzArt. 11166 3/8 x 3/4 mit Kunststoff-Einsatz
Structural Pressure 12 bar (174 psi)Working Pressure 6 bar (87 psi)Temperature Rating max. 110C (230F) water (no steam)Rotating CapBrass Body and CapFluid: Water
Available in: Fig. 12501 1/8 NPTFig. 12502 1/4 NPTFig. 12503 3/8 ISO 228Fig. 12504 1/2 ISO 228
Available in:Fig. 11153 3/8 x 3/8 with Plastic InsertFig. 11164 1/2 x 1/2 with Brass InsertFig. 11155 3/8 x 1/2 with Plastic InsertFig. 11166 3/8 x 3/4 with Plastic Insert
Dimensions in mmMasse in mm
1 1 BODY / KRPER
2 2 FLOAT / SCHWIMMER
3 O RING / O-RING
4 FLOAT LEVER / SCHWIMMERARM
5 GASKET / DICHTUNG
6 SPRING / FEDER
7 NUT / MUTTER
8 CAP / DECKEL
9 VENTING CONNECTIONENTLFTUNGSVERSCHRAUBUNG
10 SMALL CAP / KPPCHEN
1 Cu Zn 40 Pb 2 - DIN EN 12165
2 Cu Zn 40 Pb 2 - DIN EN 12165
3 TPX
4 Cu Zn 39 Pb 3 - DIN EN 12164
5 Cu Zn 39 Pb 3 - DIN EN 12164
6 Stainlees Steel - Edelstahl AISI 302
7 Polypropylene - Polypropylen
8 NBR 70 Shore
9 NBR 70 Shore
10 NBR 70 Shore
G A L H H1 B SW 1/8 75 48 98 87 10,5 231/4 75 48 98 87 10,5 233/8 75 48 98 87 10,5 231/2 75 48 98 87 10,5 27
19QUALITY SINCE 1972
101 Automatic Air Vent Original with StopvalveAutomatischer Schnellentlfter Original mit Absperrventil
Absperrventil zu Original Artikel 111 Stopvalve for Original Figure 111
Nenndruck 12 barArbeitsdruck 4 barMaximale Temperatur 110C Wasser (ohne Dampf)
Verchromter Schnellentlfter in GanzmetallausfhrungHygroskopische Sicherheitskappe mit QuellstopscheibenMedium: Wasser
Ausfhrungen: Art. 10101 1/8 NPTArt. 10102 1/4 NPT Art. 10103 3/8 ISO 228Art. 10104 1/2 ISO 228
Ausfhrungen: Art. 11153C 3/8 x 3/8 verchromt mit Messing-EinsatzArt. 11155C 3/8 x 1/2 verchromt mit Kunststoff-Einsatz
Structural Pressure 12 bar (174 psi)Working Pressure 4 bar (58 psi)Temperature Rating max. 110C (230F) water (no steam)
Chrome Plated Air Vent in Full Metal DesignHygroscopic Relief CapFluid: Water
Available in: Fig. 10101 1/8 NPTFig. 10102 1/4 NPTFig. 10103 3/8 ISO 228Fig. 10104 1/2 ISO 228
Available in: Fig. 11153C 3/8 x 3/8 Chrome plated with Brass InsertFig. 11155C 3/8 x 1/2 Chrome plated with Plastic Insert
G B SW H A 1/8 10,5 23 88,5 48,51/4 10,5 23 88,5 48,53/8 10,5 23 88,5 48,51/2 10,5 27 88,5 48,5
Dimensions in mmMasse in mm 1 Cu Zn 40 Pb 2 - DIN EN 12165
2 Polypropylene - Polypropylen
3 Stainlees Steel - Edelstahl AISI 304
4 Cu Zn 39 Pb 3 - DIN EN 12164
5 Stainlees Steel - Edelstahl AISI 304
6 NBR 60 Shore
7 NBR 70 Shore
8 Cu Zn 40 Pb 2 - DIN EN 12165
9 Stainlees Steel - Edelstahl AISI 302
10 Polyacetalic - Polyacetal
11 NBR 70 Shore
12 Prespan
13 Cu Zn 39 Pb 3 - DIN EN 12164
1 BODY / KRPER
2 FLOAT / SCHWIMMER
3 FLOAT LEVER / SCHWIMMERARM
4 SMALL STEM / ACHSE
5 LEVER SUPPORT / SCHWIMMERARMHALTER
6 O RING / O-RING
7 O RING / O-RING
8 CAP / DECKEL
9 SPRING / FEDER
10 STEM STOP / MUTTER
11 O RING / O-RING
12 HYGROSCOPIC GASKETSQUELLSTOPSCHEIBEN
13 HYGROSCOPIC CAPHYGROSKOPISCHE KAPPE
13
11
12
10
9
8
5
6
4
7
3
2
1
20 QUALITY SINCE 1972
123 Automatic High Pressure Air Vent with StopvalveAutomatischer Hochdruck-Schnellentlfter mit Absperrventil
Nenndruck 18 barArbeitsdruck 11 barMaximale Temperatur 110C Wasser (ohne Dampf)
Messing verchromtMedium: Wasser
Ausfhrungen: Art. 12301 1/8 NPT Art. 12302 1/4 NPTArt. 12303 3/8 ISO 228Art. 12304 1/2 ISO 228
Structural Pressure 18 bar (261 psi)Working Pressure 11 bar (159,5 psi)Temperature Rating max. 110C (230F) water (no steam)
Chrome Plated Brass Body and CapFluid: Water
Available in: Fig. 12301 1/8 NPTFig. 12302 1/4 NPTFig. 12303 3/8 ISO 228 Fig. 12304 1/2 ISO 228
Air
ven
ts S
CH
NEL
LEN
TL
FTER
Absperrventil zu Artikel 123 Stopvalve for Figure 123Ausfhrungen: Art. 11153C 3/8 x 3/8 verchromt mit Messing-EinsatzArt. 11155C 3/8 x 1/2 verchromt mit Kunststoff-Einsatz
Available in:Fig. 11153C 3/8 x 3/8 Chrome plated with Brass InsertFig. 11155C 3/8 x 1/2 Chrome plated with Plastic Insert
G B SW H A 1/8 10,5 23 82 471/4 10,5 23 82 473/8 10,5 23 82 471/2 10,5 27 82 47
Dimensions in mmMasse in mm
1 Cu Zn 40 Pb 2 - DIN EN 12165
2 Polypropylene - Polypropylen
3 Norylic Resin - Norylharz
4 Stainless Steel - Edelstahl AISI 302
5 NBR 50 Shore
6 NBR 70 Shore
7 Polyacetalic - Polyacetal
8 Cu Zn 40 Pb 2 - DIN EN 12165
9 Cu Zn 39 Pb 3 - DIN EN 12164
9
8
5
6
4
7
3
2
1
1 BODY / KRPER
2 FLOAT / SCHWIMMER
3 FLOAT LEVER / SCHWIMMERARM
4 SPRING / FEDER
5 DISC / DICHTUNG
6 O RING / O-RING
7 PLASTIC CAP / KUNSTSTOFFDECKEL
8 CAP / DECKEL
9 SMALL CAP / KPPCHEN
21QUALITY SINCE 1972
126 Automatic Air Vent Excellent with StopvalveAutomatischer Schnellentlfter Excellent mit Absperrventil
Absperrventil zu Excellent Artikel 111Stopvalve for Excellent Figure 111
Nenndruck 12 barArbeitsdruck 6 barMaximale Temperatur 110C Wasser (ohne Dampf)Messing gelbVernickelte Ausfhrung auf AnfrageMedium: Wasser
Ausfhrungen: Art. 12601 1/8 NPTArt. 12602 1/4 NPTArt. 12603 3/8 ISO 228Art. 12604 1/2 ISO 228
Ausfhrungen: Art. 11153 3/8 x 3/8 mit Kunststoff-EinsatzArt. 11164 1/2 x 1/2 mit Messing-EinsatzArt. 11155 3/8 x 1/2 mit Kunststoff-EinsatzArt. 11166 3/8 x 3/4 mit Kunststoff-Einsatz
Structural Pressure 12 bar (174 psi)Working Pressure 6 bar (87 psi)Temperature Rating max. 110C (230F) water (no steam)Brass Body and CapNickel Plated Version on demandFluid: Water
Available in:Fig. 12601 1/8 NPTFig. 12602 1/4 NPTFig. 12603 3/8 ISO 228 Fig. 12604 1/2 ISO 228
Available in:Fig. 11153 3/8 x 3/8 with Plastic InsertFig. 11164 1/2 x 1/2 with Brass InsertFig. 11155 3/8 x 1/2 with Plastic InsertFig. 11166 3/8 x 3/4 with Plastic Insert
1 Cu Zn 40 Pb 2 - DIN EN 12165
2 Polypropylene - Polypropylen
3 Norylic Resin - Norylharz
4 Stainless Steel - Edelstahl AISI 302
5 NBR 50 Shore
6 NBR 70 Shore
7 Polyacetalic - Polyacetal
8 Cu Zn 40 Pb 2 - DIN EN 12165
9 Polypropylene - Polypropylen
G B SW H A1/8 10,5 23 83 471/4 10,5 23 83 473/8 10,5 23 83 471/2 10,5 27 83 47
Dimensions in mmMasse in mm
9
8
5
6
4
7
3
2
1
1 BODY / KRPER
2 FLOAT / SCHWIMMER
3 FLOAT LEVER / SCHWIMMERARM
4 SPRING / FEDER
5 GASKET / DICHTUNG
6 O RING / O-RING
7 PLASTIC CAP / KUNSTSTOFFDECKEL
8 CAP / DECKEL
9 SMALL CAP / KPPCHEN
Fig./Art. 001 Waste ConnectorSpritzauffnger
Fig./Art. 002 Air Inlet PreventerLufteintrittssperre
22 QUALITY SINCE 1972
126K Automatic Air Vent Excellent in Questra Automatischer Schnellentlfter Excellent aus Questra
Nenndruck 6 barArbeitsdruck 3 barMaximale Temperatur 85C Wasser (ohne Dampf)Krper und Deckel aus QuestraMedium: Wasser
Ausfhrungen: Art. 126K03 3/8 ISO 228
Structural Pressure 6 bar (87 psi)Working Pressure 3 bar (43,5 psi)Temperature Rating max. 85C (230F) water (no steam)Body and Cap in QuestraFluid: Water
Available in:Fig. 126K03 3/8 ISO 228
1 QUESTRA NWA 7030
2 Polypropylene - Polypropylen
3 Norylic Resin - Norylharz
4 Stainless Steel - Edelstahl AISI 302
5 NBR 50 Shore
6 NBR 70 Shore
7 Polyacetalic - Polyacetal
8 QUESTRA NWA 7030
9 Polypropylene - Polypropylen
10 NBR 70 Shore
G B SW H A3/8 10,5 24 83 48
Dimensions in mmMasse in mm
Air
ven
ts S
CH
NEL
LEN
TL
FTER
10
9
8
5
6
4
7
3
2
1
1 BODY / KRPER
2 FLOAT / SCHWIMMER
3 FLOAT LEVER / SCHWIMMERARM
4 SPRING / FEDER
5 GASKET / DICHTUNG
6 O RING / O-RING
7 PLASTIC CAP / KUNSTSTOFFDECKEL
8 CAP / DECKEL
9 SMALL CAP / KPPCHEN
10 O RING / O-RING
23QUALITY SINCE 1972
121 Automatic High Capacity Air Vent Minival with StopvalveAutomatischer Schnellentlfter Minival mit hoher Entlftungskapazitt, mit Absperrventil
Absperrventil zu Minival Artikel 111 Stopvalve for Minival Figure 111
Nenndruck 12 barArbeitsdruck 6 barMaximale Temperatur 110C Wasser (ohne Dampf)
Messing gelbVernickelte Ausfhrung auf AnfrageVersion mit Kppchen aus Messing auf AnfrageMedium: Wasser
Ausfhrungen: Art. 12101 1/8 NPTArt. 12102 1/4 NPTArt. 12103 3/8 ISO 228Art. 12104 1/2 ISO 228
Ausfhrungen: Art. 11153 3/8 x 3/8 mit Kunststoff-EinsatzArt. 11164 1/2 x 1/2 mit Messing-EinsatzArt. 11155 3/8 x 1/2 mit Kunststoff-EinsatzArt. 11166 3/8 x 3/4 mit Kunststoff-Einsatz
Fig./Art. 001 Waste ConnectorSpritzauffnger
Fig./Art. 002 Air Inlet PreventerLufteintrittssperre
Structural Pressure 12 bar (174 psi)Working Pressure 6 bar (87 psi)Temperature Rating max. 110C (230F) water (no steam)
Brass Body and CapNickel Plated Version on demand Version with small brass cap on demandFluid: Water
Available in: Fig. 12101 1/8 NPTFig. 12102 1/4 NPTFig. 12103 3/8 ISO 228 Fig. 12104 1/2 ISO 228
Available in: Fig. 11153 3/8 x 3/8 with Plastic InsertFig. 11164 1/2 x 1/2 with Brass InsertFig. 11155 3/8 x 1/2 with Plastic InsertFig. 11166 3/8 x 3/4 with Plastic Insert
G B SW H A 1/8 10,5 23 83 471/4 10,5 23 83 473/8 10,5 23 83 471/2 10,5 27 83 47
Dimensions in mmMasse in mm 1 Cu Zn 40 Pb 2 - DIN EN 12165
2 Polypropylene - Polypropylen
3 Norylic Resin - Norylharz
4 Stainlees Steel - Edelstahl AISI 302
5 NBR 50 Shore
6 NBR 70 Shore
7 Polyacetalic - Polyacetal
8 Cu Zn 40 Pb 2 - DIN EN 12165
9 Polypropylene - Polypropylen
1 BODY / KRPER
2 FLOAT / SCHWIMMER
3 FLOAT LEVER / SCHWIMMERARM
4 SPRING / FEDER
5 GASKET / DICHTUNG
6 O RING / O-RING
7 PLASTIC CAP / KUNSTSTOFFDECKEL
8 CAP / DECKEL
9 SMALL CAP / KPPCHEN
9
8
5
6
4
7
3
2
1
24 QUALITY SINCE 1972
Air
ven
ts S
CH
NEL
LEN
TL
FTER
120 Automatic Air Vent Micro with StopvalveAutomatischer Schnellentlfter Micro mit Absperrventil
Nenndruck 12 barArbeitsdruck 8 barMaximale Temperatur 110C Wasser (ohne Dampf)
Messing gelbVernickelte Ausfhrung auf AnfrageMedium: Wasser
Ausfhrungen: Art. 12001 1/8 NPTArt. 12002 1/4 NPTArt. 12003 3/8 ISO 228Art. 12004 1/2 ISO 228
Structural Pressure 12 bar (174 psi)Working Pressure 8 bar (116 psi)Temperature Rating max. 110C (230F) water (no steam)
Brass Body and CapNickel Plated Version on demand Fluid: Water
Available in: Fig. 12001 1/8 NPT Fig. 12002 1/4 NPTFig. 12003 3/8 ISO 228Fig. 12004 1/2 ISO 228
Absperrventil zu Micro Artikel 111 Stopvalve for Micro Figure 111Ausfhrungen: Art. 11153 3/8 x 3/8 mit Kunststoff-EinsatzArt. 11164 1/2 x 1/2 mit Messing-EinsatzArt. 11155 3/8 x 1/2 mit Kunststoff-EinsatzArt. 11166 3/8 x 3/4 mit Kunststoff-Einsatz
Available in: Fig. 11153 3/8 x 3/8 with Plastic InsertFig. 11164 1/2 x 1/2 with Brass InsertFig. 11155 3/8 x 1/2 with Plastic InsertFig. 11166 3/8 x 3/4 with Plastic Insert
Fig./Art. 001 Waste ConnectorSpritzauffnger
Fig./Art. 002 Air Inlet PreventerLufteintrittssperre
1 BODY / KRPER
2 FLOAT / SCHWIMMER
3 FLOAT LEVER / SCHWIMMERARM
4 SPRING / FEDER
5 GASKET / DICHTUNG
6 O RING / O-RING
7 PLASTIC CAP / KUNSTSTOFFDECKEL
8 CAP / DECKEL
9 SMALL CAP / KPPCHEN
9
8
5
6
4
7
3
2
1
G B SW H A 1/8 10,5 19 80 391/4 10,5 19 80 393/8 8,8 22 78 391/2 10,5 22 80 39
Dimensions in mmMasse in mm 1 Cu Zn 40 Pb 2 - DIN EN 12165
2 Polypropylene - Polypropylen
3 Norylic Resin - Norylharz
4 Stainlees Steel - Edelstahl AISI 302
5 NBR 50 Shore
6 NBR 70 Shore
7 Cu Zn 40 Pb 2 - DIN EN 12165
8 Polyacetalic - Polyacetal
9 Polypropylene - Polypropylen
25QUALITY SINCE 1972
120L Automatic Air Vent Micro with side ventingAutomatischer Schnellentlfter Micro mit seitlichem Abgang
Nenndruck 12 barArbeitsdruck 8 barMaximale Temperatur 110C Wasser (ohne Dampf)
Messing gelbVernickelte Ausfhrung auf AnfrageMedium: Wasser
Ausfhrungen: Art. 120L03 3/8 ISO 228
Structural Pressure 12 bar (174 psi)Working Pressure 8 bar (116 psi)Temperature Rating max. 110C (230F) water (no steam)
Brass Body and CapNickel Plated Version on demand Fluid: Water
Available in:Fig. 120L03 3/8 ISO 228
1 Cu Zn 40 Pb 2 - DIN EN 12165
2 Polypropylene - Polypropylen
3 Norylic Resin - Norylharz
4 Stainless Steel - Edelstahl AISI 302
5 NBR 50 Shore
6 NBR 70 Shore
7 Polyacetalic - Polyacetal
8 Cu Zn 40 Pb 2 - DIN EN 12165
9 Polypropylene - Polypropylen
G B H A L3/8 10,5 63 39 52,5
Dimensions in mmMasse in mm
Absperrventil zu Micro L Artikel 111Stopvalve for Micro L Figure 111Ausfhrungen: Art. 11153 3/8 x 3/8 mit Kunststoff-EinsatzArt. 11155 3/8 x 1/2 mit Kunststoff-Einsatz
Available in:Fig. 11153 3/8 x 3/8 with Plastic InsertFig. 11155 3/8 x 1/2 with Plastic Insert
1 BODY / KRPER
2 FLOAT / SCHWIMMER
3 FLOAT LEVER / SCHWIMMERARM
4 SPRING / FEDER
5 GASKET / DICHTUNG
6 O RING / O-RING
7 PLASTIC CAP / KUNSTSTOFFDECKEL
8 CAP / DECKEL
9 SMALL CAP / KPPCHEN
9
8
5
6
4
7
3
2
1
Fig./Art. 001 Waste ConnectorSpritzauffnger
Fig./Art. 002 Air Inlet PreventerLufteintrittssperre
26 QUALITY SINCE 1972
Air
ven
ts S
CH
NEL
LEN
TL
FTER
116 Automatic Design Angle Air Vent Colombo for Radiators Automatischer Design-Eckentlfter Colombo fr Heizkrper
Nenndruck 12 barArbeitsdruck 3 barMaximale Temperatur 110C Wasser (ohne Dampf)
Messing verchromt oder weiss lackiert RAL 9016Hygroskopische Sicherheitskappe mit QuellstopscheibenMit selbstdichtendem Gewinde und KontermutterMedium: Wasser
Ausfhrungen: Art. 11604 Verchromt, ISO 228Art. 11604 W weiss RAL 9016, ISO 228
Structural Pressure 12 bar (174 psi)Working Pressure 3 bar (43,5 psi)Temperature Rating max. 110C (230F) water (no steam)
Chromium Plated Brass or white RAL 9016 Hygroscopic Relief Cap With self-sealing Thread and NutFluid: Water
Available in: Fig. 11604 Chromium plated, ISO 228Fig. 11604 W White RAL 9016, ISO 228
G H H1 L A 1/2 58 41 39 39
Dimensions in mmMasse in mm
1 Cu Zn 40 Pb 2 - DIN EN 12165
2 Polypropylene - Polypropylen
3 Stainlees Steel - Edelstahl AISI 302
4 Cu Zn 40 Pb 2 - DIN EN 12165
5 Prespan
6 Cu Zn 39 Pb 3 - DIN EN 12164
7 Phosphor Bronze - Phosphorbronze
8 Polyacetalic - Polyacetal
9 NBR 70 Shore
10 NBR 50 Shore
11 Polyacetalic - Polyacetal
12 PTFE
13 Cu Zn 39 Pb 3 - DIN EN 12164
14 NBR 60 Shore
1 GASKET / DICHTUNG
2 NUT/KONTERMUTTER
3 BODY / KRPER
4 FLOAT / SCHWIMMER
5 FLOAT LEVER / SCHWIMMERARM
6 GASKET / DICHTUNG
7 SPRING / FEDER
8 O RING / O-RING
9 PLASTIC CAP / KUNSTSTOFFDECKEL
10 GASKET / DICHTUNG
11 CAP / DECKEL
12 SCREW STOP / BLOCKIERUNG FR SCHRAUBE
13 GASKET / DICHTUNG
14 HYGROSCOPIC GASKETSQUELLSTOPSCHEIBEN
15 SCREW / SCHRAUBE
15
14
13
12
11
10
9
8
5
6
4
7
3
2
1
27QUALITY SINCE 1972
117 Automatic Design Air Vent Colombo for RadiatorsAutomatischer Design-Entlfter Colombo fr Heizkrper
Nenndruck 12 barArbeitsdruck 3 barMaximale Temperatur 110C Wasser (ohne Dampf)
Messing verchromt oder weiss lackiert RAL 9016Hygroskopische Sicherheitskappe mit QuellstopscheibenMedium: Wasser
Ausfhrungen: Art. 11704 Verchromt, ISO 228Art. 11704 W weiss RAL 9016, ISO 228
Structural Pressure 12 bar (174 psi)Working Pressure 3 bar (43,5 psi)Temperature Rating max. 110C (230F) water (no steam)
Chromium Plated Brass or white RAL 9016 Hygroscopic Relief Cap Fluid: Water
Available in: Fig. 11704 Chromium plated, ISO 228Fig. 11704 W White RAL 9016, ISO 228
G H SW A B 1/2 73,5 27 39 10,5
Dimensions in mmMasse in mm
1 Cu Zn 40 Pb 2 - DIN EN 12165
2 Polypropylene - Polypropylen
3 Stainlees Steel - Edelstahl AISI 302
4 Cu Zn 40 Pb 2 - DIN EN 12165
5 Prespan
6 Cu Zn 39 Pb 3 - DIN EN 12164
7 Phosphor Bronze - Phosphorbronze
8 Polyacetalic - Polyacetal
9 NBR 70 Shore
10 NBR 50 Shore
11 Polyacetalic - Polyacetal
12 NBR 70 Shore
13 NBR 60 Shore
1 BODY / KRPER
2 FLOAT / SCHWIMMER
3 FLOAT LEVER / SCHWIMMERARM
4 GASKET / DICHTUNG
5 SPRING / FEDER
6 O RING / O-RING
7 PLASTIC CAP / KUNSTSTOFFDECKEL
8 GASKET / DICHTUNG
9 CAP / DECKEL
10 SCREW STOP / BLOCKIERUNG FR SCHRAUBE
11 GASKET / DICHTUNG
12 HYGROSCOPIC GASKETSQUELLSTOPSCHEIBEN
13 SCREW / SCHRAUBE
13
12
1110
9
8
5
6
4
7
3
2
1
Fig./Art. 117 Adapter, reduction from 1/2 to 3/8Adapter, Reduktion von 1/2 auf 3/8
28 QUALITY SINCE 1972
13
12
11
10
9
8
5
6
4
7
3
2
1
115 Automatic Air Vent for RadiatorsAutomatischer Eckentlfter fr Heizkrper
Nenndruck 12 barArbeitsdruck 2,5 bar Maximale Temperatur 110C Wasser (ohne Dampf)
Verchromter Schnellentlfter in GanzmetallausfhrungHygroskopische Sicherheitskappe mit QuellstopscheibenMedium: Wasser
Ausfhrungen: Art.11504 1/2 ISO 228
Structural Pressure 12 bar (174 psi)Working Pressure 2,5 bar (36,3 psi)Temperature Rating max. 110C (230F) water (no steam)
Chrome Plated Air Vent in Full Metal DesignHygroscopic Relief CapFluid: Water
Available in: Fig. 11504 1/2 ISO 228
G L L1 SW H A 1/2 58 10,5 25 59 48,5
Dimensions in mmMasse in mm
1 Cu Zn 40 Pb 2 - DIN EN 12165
2 Polypropylene - Polypropylen
3 Stainlees Steel - Edelstahl AISI 304
4 Cu Zn 39 Pb 3 - DIN EN 12164
5 Stainlees Steel - Edelstahl AISI 304
6 NBR 60 Shore
7 NBR 70 Shore
8 Cu Zn 40 Pb 2 - DIN EN 12165
9 NBR 70 Shore
10 Polyacetalic - Polyacetal
11 Stainlees Steel - Edelstahl AISI 302
12 Prespan
13 Cu Zn 39 Pb 3 - DIN EN 12164
1 BODY / KRPER
2 FLOAT / SCHWIMMER
3 FLOAT LEVER / SCHWIMMERARM
4 SMALL STEM / ACHSE
5 LEVER SUPPORT / SCHWIMMERARMHALTER
6 O RING / O-RING
7 O RING / O-RING
8 CAP / DECKEL
9 SPRING / FEDER
10 STEM STOP / MUTTER
11 O RING / O-RING
12 HYGROSCOPIC GASKETSQUELLSTOPSCHEIBEN
13 HYGROSCOPIC CAPHYGROSKOPISCHE KAPPEA
ir v
ents
SC
HN
ELLE
NTL
FT
ER
29QUALITY SINCE 1972
129
100
Automatic Air Vent KombiSchnellentlfter Kombi
Pressure GaugeManometer
Ohne Entleeren der Heizungsanlage knnen Schnellentlfter und/oder Manometer ausgetauscht werdenNenndruck 12 barArbeitsdruck Schnellentlfter 6 barMaximale Temperatur 110C Wasser (ohne Dampf)Medium: Wasser
Ausfhrungen: Art. 12904 1/2 mit Schnellentlfter, Manometer und Absperrventil
Rohrfeder-ManometerGehuse-Durchmesser 63 mmAnschlussgewinde 1/4Anschluss axial (hinten) oder radial (unten)Diverse Skalenbereiche von 0-4 bar bis 0-25 bar erhltlichMin. / max. Temperatur -20C bis 60C Wasser (ohne Dampf)
Manometer fr geschlossene Heizungsanlagen mit Stellzeiger, grnem Feld und roter Marke mit Skala 0-4 bar erhltlich
Air Vent and/or Pressure Gauge can be replaced without draining the Heating SystemStructural Pressure 12 bar (174 psi)Working Pressure Air Vent 6 bar (87 psi) Temperature Rating 110C (230F) water (no steam)Fluid: Water
Available in: Fig. 12904 1/2 with Air Vent, Pressure Gauge and Stopvalve
Pressure Gauge with Bourdon TubeCase Diameter 63 mmConnection Thread 1/4Bottom Connection or back, centric ConnectionDifferent Pressure Ranges from 0-4 to 0-25 bar availableMin. / max. Temperature Rating -20C to 60C (-68F to 140F) water (no steam)
For closed Heating Systems Pressure Gauge with pressure scale 0-4 bar with red adjustable Pointer and green Mark available
G H W SW 1/2 87 65 25
Dimensions in mmMasse in mm
30 QUALITY SINCE 1972
130/132 Pressure Relief ValveMembransicherheitsventil
Pressmessing mit Kunststoff-EinsatzAnsprechdruck: 2,5 - 7 bar Heizung (orange Kappe)7,5 - 10 bar Sanitr (blaue Kappe)
Max. Temperatur 110C Wasser (ohne Dampf)
Grssen: 1/2x1/2, 3/4x3/4 und 1x1 fr Art. 130 FF und Art. 132 FF (Innen- x Innengewinde)
1/2x1/2 und 3/4x3/4 fr Art. 130 MF und Art. 132 MF (Innen- x Aussengewinde)
Ausfhrungen: Art. 130 FF Innen-x Innengewinde (Heizung, orange Kappe)Art. 130 MF Innen-x Aussengewinde (Heizung, orange Kappe)Art. 132 FF Innen-x Innengewinde (Sanitr, blaue Kappe)Art. 132 MF Innen-x Aussengewinde (Sanitr, blaue Kappe)
Brass Body with Plastic InsertPressure Relief Setting: 2,5 - 7 bar (36,3 and 101,5 psi) Heating (orange cap)7,5 - 10 bar (108,8 - 145 psi) Potable Water System (blue cap)
Temperature Rating max. 110C (230F) water (no steam)
Sizes: 1/2x1/2, 3/4x3/4 and 1x1 for Fig. 130 FF and Fig. 132 FF (Female Ends)
1/2x1/2 and 3/4x3/4 for Fig. 130 MF and Fig. 132 MF (Male/Female Ends)
Available in:Fig. 130 FF Female ends (Heating, orange cap)Fig. 130 MF Female/Male Ends (Heating, orange cap)Fig. 132 FF Female ends (Potable Water System, blue cap)Fig. 132 MF Female/Male Ends (Potable Water System, blue cap)
130FF 130MF
132FF 132MF
Pre
ssure
Rel
ief
Valv
es
MEM
BRA
NSI
CH
ERH
EITS
VEN
TILE
130MF132MF
130FF132FF
Dimensions in mmMasse in mm
G G1 D L L1 L2 L3 H1/2 1/2 13 26,5 10 9 17 623/4 3/4 17 32 16 12 25 82
1 1 22 38 20 15 30 103
Dimensions in mmMasse in mm
G G1 D L L1 L2 L3 H1/2 1/2 13 26,5 10 10 23 653/4 3/4 17 32 16 12 31 88
31QUALITY SINCE 1972
Dimensions in mmMasse in mm
A A1 DN H h1/2 3/4 15 50 283/4 1 20 52 34
1 1 1/4 25 79 401 1/4 1 1/2 32 110 461 1/2 2 40 176 55
2 2 1/2 50 195 66
131/133 Pressure Relief ValveMembransicherheitsventil
TV geprft fr geschlossene Heizungsanlagen gemss DIN EN 12828TV geprft fr den Anschluss von geschlossenen Trinkwasserwrmern gemss DIN 1988 und 4753, Teil 1 und TRD 721
Gehuse aus Pressmessing gelb (DN 15 DN 32) Gehuse aus Rotguss (DN 40 DN 50)
Ansprechdruck: 2,5 und 3 bar Heizung (rote Kappe)6, 8 und 10 bar Sanitr (schwarze Kappe)
Max. Temperatur 110C Wasser (ohne Dampf)
Grssen: 1/2x3/4, 3/4x1, 1x1 1/4, 1 1/4x1 1/2, 1 1/2x2 und 2x2 1/2
Ausfhrungen: Art. 131 Innen-x Innengewinde, TV geprft (Heizung, rote Kappe)Art. 133 Innen-x Innengewinde, TV geprft (Sanitr, schwarze Kappe)
TV approved for heating according to the norm DIN EN 12828TV approved for potable water system according to the norm DIN 1988 and 4753, Part 1 and TRD 721
Brass body (DN 15 DN 32)Bronze body (DN 40 DN 50)
Pressure Relief Setting: 2,5 and 3 bar (36,3 and 43,5 psi) Heating (red cap)6, 8 and 10 bar (87, 116 and 145 psi) Potable Water System (black cap)
Temperature Rating max. 110C (230F) water (no steam)
Sizes: 1/2x3/4, 3/4x1, 1x1 1/4, 1 1/4x1 1/2, 1 1/2x2 and 2x2 1/2
Available in:Fig. 131 Female Ends, TV approved (Heating, red cap)Fig. 133 Female Ends, TV approved (Potable Water System, black cap)
131133
32 QUALITY SINCE 1972
260
279
Filling UnitFllgruppe
Thermal Safety ValveThermische Ablaufsicherung
Fllgruppe zur Automatisierung des Fllvorganges bei geschlossenen HeizungsanlagenBestehend aus Rck ussverhinderer (DVGW geprft), Druckminderer, Absperrung, Prfeinrichtung und Niro-Schmutzfnger, einschliesslich Schlauchtllenanschluss.Manometeranschlsse G1/4 beidseitigEingangsdruck PN 10Ausgangsdruck regelbar von 0,5 bis 3 bar, werkseitig voreingestellt auf 1,5 barMax. Temperatur 90CGehuse aus Pressmessing
Ausfhrungen: Fig. 26004 1/2
Zur thermischen Absicherung von feststoffbefeuerten Heizungskesselnin geschlossenen Heizungsanlagen nach DIN EN 12828ffnet bei Erreichen der Ansprechtemperatur von 95C und fhrt Kaltwasser zur Abkhlung des Kessels zu
Druck PN 10Ansprechtemperatur 95CMaximale Temperatur 125C Wasser (ohne Dampf)Gehuse aus Messing
Ausfhrungen: Art. 27906.13 3/4 mit 1.3m Kapillarrohr
Filling Unit for automatic re lling of closed heating systemConsisting of pressure reducer (DVGW certi ed), stop valve,check valve and lter, complete with pipe connection.Pressure gauge connection 1/4 on both sidesInlet pressure max.10 bar (145 psi), Outlet pressure adjustable between 0,5 and 3 bar(7,25 to 43,5 psi)Temperature rating max. 90C (194F)Brass body
Available in:Fig. 26004 1/2
To prevent excess Temperatures of solid-fuel- red Boilers in closed Heating Systems according to DIN EN 12828Opens when the Factory Temperature reaches 95C (203F) and supplies cold water to cool-down the boiler
Pressure Rating PN 10 (145 psi)Factory Temperature Setting 95C (203F)Temperature Rating max. 125C (257F) water (without steam)Brass Body
Available in:Fig. 27906.13 3/4 with 1.3m capillary tube
33QUALITY SINCE 1972
515
516
517
Pressure Reducing ValveDruckminderer
Pressure Reducing ValveDruckminderer
Flanged Pressure Reducing ValveFlanschdruckminderer
DVGW geprftMit beidseitigen Manometerstutzen 1/4 und SchmutzfngerEingangsdruck max. 25 bar Ausgangsdruck regelbar von 1,5 bis 6 bar, werkseitig voreingestellt auf 4 barMaximale Temperatur 30C WasserGehuse aus Rotguss
Ausfhrungen: Art. 515 mit beidseitigen TllenArt. 515 FF Innen-x Innengewinde
Mit einem Manometerstutzen 1/4 unten und SchmutzfngerEingangsdruck max. 16 bar Ausgangsdruck regelbar von 1,5 bis 6 bar, werkseitig voreingestellt auf 4 barMaximale Temperatur 60C WasserGehuse aus Pressmessing
Ausfhrungen: Art. 516 EURO Innen-x Innengewinde
Mit Minikugelhhnen, Manometeranschlssen und SchmutzfngerEingangsdruck max. 16 bar Ausgangsdruck regelbar von 1,5 bis 6 bar, werkseitigvoreingestellt auf 4 barMaximale Temperatur 30C WasserGehuse aus Rotguss
Ausfhrungen: Art. 517 mit beidseitigen Flanschanschlssen
DVGW approvedWith Pressure Gauge Connections 1/4 on both sides and StrainerInlet Pressure max. 25 bar (362,50 psi)Outlet Pressure adjustable between 1,5 and 6 bar (21,8 and 87 psi), factory pre-set at 4 bar (58 psi)Temperature Rating max. 30C (86F) waterBronze Body
Available in: Fig. 515 with Hose Unions on both sidesFig. 515 FF Female Ends
With Pressure Gauge Connection 1/4 (bottom connection) and StrainerInlet Pressure max. 16 bar (232 psi)Outlet Pressure adjustable between 1,5 and 6 bar (21,8 and 87 psi), factory pre-set at 4 bar (58 psi)Temperature Rating max. 60C (140F) waterBrass Body
Available in: Fig. 516 EURO Female Ends
With Mini Ball Valves, Pressure Gauge Connections and StrainerInlet Pressure max. 16 bar (232 psi)Outlet Pressure adjustable between 1,5 and 6 bar (21,8 and 87 psi), factory pre-set at 4 bar (58 psi)Temperature Rating max. 30C (86F) waterBronze Body
Available in:Fig. 517 Flanged Ends
Pre
ssure
Red
uci
ng V
alv
es
DRU
CKM
IND
ERER
A DN d L L1 I H D 1/2 15 15 132 106 75 123 58 3/4 20 18 143 117 75 123 58
1 25 22 161 135 87 121 581 1/4 32 190 170 105 176 SW 751 1/2 40 220 205 130 176 SW 75
2 50 255 240 140 180 SW 75
D DN L H 3/8 10 64 100 1/2 15 72 1003/4 20 74 100
DN L H H165 290 283 18580 310 283 200
100 350 283 220
Dimensions in mmMasse in mm
Dimensions in mmMasse in mm
Dimensions in mmMasse in mm
34 QUALITY SINCE 1972
235236237
Check ValveRckschlagventil
Arbeitsdruck: Artikel 235/237 PN 16 *Artikel 235.O/237.O PN 25 * Artikel 236 bis 1 PN 25 * / ab 1 1/4 PN 18 * Artikel 236.O bis 3/4 PN 50 * / ab 1 PN 35 *
Maximale Temperatur 100C Wasser (ohne Dampf), (je nach Druck)Maximale Temperatur Artikel 236.O 150C
Pressmessing - Edelstahlfederffnungsdruck ca. 0,02 bar
Ausfhrungen:Art. 235 Euro IArt. 235.O Euro I (Ganzmetallausfhrung)Art. 236 Euro IIArt. 236.O Euro II (Ganzmetallausfhrung) Art. 237 Fussventil mit Nylon AnschlussArt. 237.O Fussventil mit Messing - Anschluss (Ganzmetallausfhrung)
* 18C Wasser
Working Pressure:Figure 235/237 PN 16 (232 psi) * Figure 235.O/237.O PN 25 (362,5 psi) *Figure 236 PN 25 till 1 (362,5 psi) * / from 1 1/4 PN 18 (261 psi) *Figure 236.O till 3/4 PN 50 (725 psi) * / from 1 PN 35 (507 psi) *
Temperature Rating max. 100C (212F) water (no steam), (depending on pressure)Temperature Rating max. Figure 236.O 150C (302F)
Brass Body - Stainless Steel SpringOpening Pressure appr. 0,02 bar (0,29 psi)
Available in:Fig. 235 Euro I Fig. 235.O Euro I (Version with inside structure in brass)Fig. 236 Euro II Fig. 236.O Euro II (Version with inside structure in brass)Fig. 237 Check Valve with Filter with nylon connectionFig. 237.O Check Valve with Filter with brass connection (Version with inside structure in brass)
* 18C (64,4F) water
Chec
k V
alv
es R
C
KSC
HLA
GVE
NTI
LE
1 Cu Zn 40 Pb 2 - DIN EN 12165
2 Cu Zn 40 Pb 2 - DIN EN 12165
3 Fig. / Art. 235: POMFig. / Art. 235.O: Cu Zn 39 Pb 3 - DIN EN 12164
4 Fig. / Art. 235: POMFig. / Art. 235.O: Cu Zn 39 Pb 3 - DIN EN 12164
5 NBR 70 Shore
6 Stainless Steel - Edelstahl AISI 302
7 NBR 70 Shore
1 Cu Zn 40 Pb 2 - DIN EN 12165
2 Stainless Steel - Edelstahl AISI 302
3 Fig. / Art. 236: NBR 70 ShoreFig. / Art. 236.O: Viton
4 Fig. / Art. 236: POMFig. / Art. 236.O: Stainless Steel - Edelstahl AISI 304
5 Stainless Steel - Edelstahl AISI 302
6 Cu Zn 40 Pb 2 - DIN EN 12165
1 Cu Zn 40 Pb 2 - DIN EN 12165
2 Cu Zn 40 Pb 2 - DIN EN 12165
3 Fig. / Art. 237: POMFig. / Art. 237.O: Cu Zn 39 Pb 3 - DIN EN 12164
4 Fig. / Art. 237: POM Fig. / Art. 237.O: Cu Zn 40 Pb 2 - DIN EN 12165
5 NBR 70 Shore
6 Stainless Steel - Edelstahl AISI 302
7 NBR 70 Shore
8 Stainless Steel - Edelstahl AISI 302
9 Fig. / Art. 237: NylonFig. / Art. 237.O: Cu Zn 40 Pb 2 - DIN EN 12165
235
236
237
35QUALITY SINCE 1972
Euro I
Euro II
Check Valve with FilterFussventil
235
236
237
G D L D1 L1 SW1/2 29 47 15 9,6 253/4 38 52 20 11,2 31
1 48 62 25 13,5 381 1/4 56 65 32 12,5 471 1/2 69 73 40 14,5 54
2 83 80 48 16 66
Dimensions in mmMasse in mm
Dimensions in mmMasse in mm
Dimensions in mmMasse in mm
G D L3/8 29 521/2 32 583/4 39 65
1 47 751 1/4 60 801 1/2 67 86
2 83 94
G D L1/2 29 893/4 38 101
1 48 1161 1/4 56 1241 1/2 69 142
2 83 164
36 QUALITY SINCE 1972
695 Gas Safety Shut-off Valve with thermally released Shut-off Device (TAE) DIN-DVGW for GasGasanschluss-Kugelhahn mit thermisch auslsender Absperreinrichtung aus Stahl (TAE) DIN-DVGW Gas
1 Steel - Stahl
2 PTFE
3 Cu Zn 39 Pb 3 - DIN EN 12164
4 Cu Zn 40 Pb 2 - DIN EN 12165
5 NBR 70 Shore
6 Cu Zn 40 Pb 2 - DIN EN 12165
7 Cu Zn 39 Pb 3 - DIN EN 12164
8 NBR 70 Shore9 Cu Zn 39 Pb 3 - DIN EN 12164
10 Stainless Steel - Stahl AISI 302
11 Stainless Steel - Stahl AISI 302
12 Aluminium Al Si 11 Cu 2 (Fe)
13 Polypropylene - Polypropylen
14 Steel, zinc plated - Stahl, verzinkt
15 Cu Zn 39 Pb 3 - DIN EN 12164
DIN-DVGW geprft nach DIN EN 331 und DIN 3586Prfdruck MOP 5 (5 bar)Min. / max. Umgebungstemperatur -20C bis 60CAuslsetemperatur der TAE 100C -8K
Kugelhahn aus Pressmessing verchromtTAE aus verchromtem Stahl bei 1/2 und 3/4, TAE aus schwarz verchromtem Stahl bei 1Reduzierter DurchgangGewinde nach ISO 7Verchromte KugelMit MULTILOGO-Sicherheitsgriff
Ausfhrungen: Art. 695 Durchgangsform, Innengewinde x berwurfmutter mit TlleArt. 695 A Eckform, Aussengewinde x berwurfmutter mit Tlle
Beide Varianten auch ohne thermisch auslsende Absperreinrichtung (TAE) erhltlichTAE kann auch einzeln bezogen werden
DIN-DVGW approved according to DIN EN 331 and DIN 3586Nominal Pressure MOP 5 (72,5 psi)Min. / max. ambient Temperature -20C to 60C (-4F to 140F)Release Temperature (TAE) 100C -8K (212F -8K)
Ball Valve in Brass Chrome PlatedSteel chrome plated TAE for 1/2 and 3/4, Steel black chrome plated TAE for 1Standard Port OpeningThreaded Ends according to ISO 7Chrome Plated BallWith MULTILOGO Safety Push-and-Turn-Handle
Available in: Fig. 695 Straight Pattern, Female End / Hose UnionFig. 695 A Angle Pattern, Male End / Hose Union
Both types available also without thermally released Shut-off Device (TAE)TAE available also individually
Ball
Valv
es K
UG
ELH
H
NE
ROSTECHNADZOR(GGTN)
37QUALITY SINCE 1972
Verwendungsbereich Eingesetzt wird der Gasanschluss-Kugelhahn in der Eck- und Durchgangsform fr Installationen nach DVGW-TRGI 1986 (Ausgabe 1996), die mit Gasen nach DVGW-Arbeitsblatt G 260 Teil 1 und mit zulssigen Betriebsberdrcken bis 5 bar betrieben werden.Es handelt sich hierbei um Gasgerte wie Gas-Heizgerte und Brauchwassererwrmer, sowie Gas-Umlaufwasserheizer, Gas-Kombiwasserheizer und Gas-Durchlaufwasserheizer.
Gemss DVGW-TRGI 1986, Ausgabe 1996 (Technische Regeln der Gas-Installation) und Muster-Feuerungsverordnung FeuVo 02/95, Ausgabe 09/97, 4 Abs. 6 schliesst die im Gasanschluss-Kugelhahn integrierte thermisch auslsende Absperreinrichtung aus Stahl (TAE) bei einer Temperatur von ber 100C die Gaszufuhr selbstttig ab und hlt mindestens einer Temperatur von 650C ber 30 Minuten stand.Die IMT-Gasanschluss-Kugelhhne schliessen nachfolgende Gasanlagen schon in einem Temperaturbereich von 92C bis 100C innerhalb von hchstens 45 Sekunden ab und bleiben bis zu einer Temperatur von 925C ber 60 Minuten dicht.
ApplicationThe Gas Safety Shut-off Valve in straight and angle pattern is used for installations according to DVGW-TRGI 1986 (Edition 1996) which use gases according to DVGW-Arbeitsblatt G 260 Part 1 and are subject to a maximum allowable operating pressure of 5 bar.These gas installations are usually central gas heating systems and water heaters such as instantaneous water heaters.
According to DVGW-TRGI 1986 (Edition 1996) and the German Fire Code Draft Recommendation (FeuVo) of 02/95, Edition 09/97, 4 Paragraph 6, the thermally released steel shut-off device (TAE) automatically shuts off the gas ow at temperatures above 100C (212F) and remains closed at 650C (1202F) for at least 30 minutes.The IMT Gas Safety Shut-off Valves automatically shuts off the gas ow already at temperatures between 92C and 100C (198F -212) within 45 seconds and keeps the installation at 925C (1697F) for at least 60 minutes gas tight.
Straight Pattern with TAE, Female End / Hose UnionDurchgangsform mit TAE, Innengewinde x berwurfmutter mit Tlle
Angle Pattern with TAE, Male End / Hose UnionEckform mit TAE, Aussengewinde x berwurfmutter mit Tlle
695
695 A
Rp D L L1 SW SW* H W1/2 12,5 94 16 27 34 57 643/4 15 117 18 32 41 58 64
1 20 124 21 41 48 62
Dimensions in mmMasse in mm
Rp R D L L1 L2 SW SW* H H* W1/2 1/2 12,5 55 16 15 27 34 57 41 643/4 3/4 15 65 18 16 32 41 58 44 64
1 1 20 80 21 19 41 48 62 54 64
Dimensions in mmMasse in mm
38 QUALITY SINCE 1972
593 Full Port Gas Ball Valve DVGW / VGW / SVGW Gas - Kugelhahn mit vollem Durchgang DVGW / VGW / SVGW
1 Cu Zn 40 Pb 2 - DIN EN 12165
2 PTFE
3 1/4-1 Cu Zn 39 Pb 3 - DIN EN 12164 1 1/4- 2 Cu Zn 40 Pb 2 - DIN EN 12165 4 Cu Zn 40 Pb 2 - DIN EN 12165
5 Cu Zn 39 Pb 3 - DIN EN 12164
6 NBR 70 Shore
7 Aluminium Al Si 11 Cu 2 (Fe)
8 Steel, zinc plated - Stahl, verzinkt
Druck MOP 5 Maximale Temperatur 60C GasMin. / max. Umgebungstemperatur bei Gas 20C bis 60C
Pressmessing gelbVoller DurchgangGewinde nach ISO 7Ausblassichere SpindelVerchromte Kugel
Ausfhrungen: Art. 593 FF Innen- x Innengewinde mit gelbem Aluminium Griff fr Gas
Pressure Rating MOP 5Temperature Rating max. 60C (140F) gasMin. / max. ambient Temperature -20C to 60C (-4F to 140F) gas
Brass BodyFull Port OpeningThreaded Ends according to ISO 7Blow Out Proof StemChrome Plated Ball
Available in: Fig. 593 FF Female Ends with yellow Aluminium Handle for Gas
Ball
Valv
es K
UG
ELH
H
NE
ROSTECHNADZOR(GGTN)
FURTHER APPROVALS IN DENMARK AND AUSTRALIAWEITERE ZULASSUNGEN IN DNEMARK UND AUSTRALIA
Dimensions in mmMasse in mm
Rp D L L1 SW H W1/4 10 50 11 21 42 1003/8 10 50 11,4 21 42 1001/2 15 62 15 26 48 1003/4 20 71 16,3 31 51 100
1 25 83 19,1 40 59 1201 1/4 32 98 21,4 50 64 1201 1/2 40 110 21,4 55 85 150
1 VALVE BODY / KRPER
2 SEAT RING / KUGELDICHTUNG
3 BALL / KUGEL
4 RETAINER-BODY END / EINSCHRAUBTEIL
5 STEM / SPINDEL
6 O RING / O-RING
7 HANDLE / GRIFF
8 HANDLE SCREW / SCHRAUBE
39QUALITY SINCE 1972
595 Full Port Gas Ball ValveDVGW / SVGW Gas - Kugelhahn mit vollem Durchgang DVGW / SVGW
1 Cu Zn 40 Pb 2 - DIN EN 12165
2 PTFE
3 1/4-1 Cu Zn 39 Pb 3 - DIN EN 12164 1 1/4- 2 Cu Zn 40 Pb 2 - DIN EN 12165 4 Cu Zn 40 Pb 2 - DIN EN 12165
5 Cu Zn 39 Pb 3 - DIN EN 12164
6 NBR 70 Shore
7 Steel, zinc plated with plastic cover Stahl, verzinkt mit Kunststoff - Beschichtung 8 Steel, zinc plated - Stahl, verzinkt
Druck: MOP 5 (5 bar) Gas
Maximale Temperatur 60C GasMin. / max. Umgebungstemperatur bei Gas 20C bis 60C
Pressmessing gelbVoller DurchgangGewinde nach ISO 7Ausblassichere SpindelVerchromte KugelMit Baulnge M3 nach DIN 3202-4 und DIN 3357-4
Ausfhrungen: Art. 595 FF Innen- x Innengewinde mit gelbem Stahlgriff fr Gas
Pressure Rating: MOP 5 (72,5 psi) gas
Temperature Rating max. 60C (140F)gasMin. / max. ambient Temperature -20C to 60C (-4F to 140F) gas
Brass BodyFull Port OpeningThreaded Ends according to ISO 7Blow Out Proof StemChrome Plated BallWith length M3 according to DIN 3202-4 and DIN 3357-4
Available in: Fig. 595 FF Female Ends with yellow Steel Handle for Gas
ROSTECHNADZOR(GGTN)
Dimensions in mmMasse in mm
Rp D L L1 SW H W1/4 10 50 11 21 39 853/8 10 60 11,4 21 39 851/2 15 75 15 26 45 853/4 20 80 16,3 32 49 85
1 25 90 19,1 41 58 1101 1/4 32 110 21,4 50 64 1101 1/2 40 120 21,4 55 81,5 135
2 50 140 25,7 70 89,5 135
1 VALVE BODY / KRPER
2 SEAT RING / KUGELDICHTUNG
3 BALL / KUGEL
4 RETAINER-BODY END / EINSCHRAUBTEIL
5 STEM / SPINDEL
6 O RING / O-RING
7 HANDLE / GRIFF
8 NUT / MUTTER
40 QUALITY SINCE 1972
The MULTILOGO handle allows the installer to mark the valve after it is installed.The installer can choose among 5 standard colours of handle inserts to identify different piping systems:
Standard colors
blueredgreenyellowwhite
Standard Farben
blaurot grn gelb weiss
Possible services
cold water or heating system returnhot water or heating system supplypotable water gas serviceair service
Mglicher Einsatz
Heizungsrcklauf, Fussbodenheizung RcklaufHeizungsvorlauf, Fussbodenheizung VorlaufTrinkwasserGasDruckluft / Zirkulation
Der MULTILOGO-Griff ermglicht dem Installateur, die Kugelhhne nach der Installation zu kennzeichnen. Lngliche Griff-Beschriftungsleisten in 5 Standardfarben dienen als Kennzeichnungstrger zur Beschriftung des Rohres, das der Kugelhahn absperrt. Spezielle Schilderhalter sind unntig.
The contractor can choose among a long handle, T-handle and yellow or red butter y-handle.
Der Installateur hat die Auswahl zwischen MULTILOGO Hebelgriff, T-Griff, rotem oder gelbem Flgelgriff.
Our ball valves 492 M Multilogo and 594 M Multilogo are delivered as follows:1 Multilogo Ball Valve1 Round Insert, yellow, IMT1 Round Insert, red, IMT1 Long Insert, yellow, pre-marked GAS1 Long Insert, green, pre-marked KALTWASSER1 Long Insert, red, pre-marked HEIZUNG VORLAUF1 Long Insert, blue, pre-marked HEIZUNG RCKLAUF
Unsere Kugelhhne 492 M Multilogo und 594 M Multilogo werden standardmssig wie folgt ausgestattet:1 Multilogo Kugelhahn1 runde Abdeckkappe gelb, beschriftet IMT1 runde Abdeckkappe rot, beschriftet IMT1 lange Beschriftungsleiste gelb, beschriftet GAS1 lange Beschriftungsleiste grn, beschriftet KALTWASSER1 lange Beschriftungsleiste rot, beschriftet HEIZUNG VORLAUF1 lange Beschriftungsleiste blau, beschriftet HEIZUNG RCKLAUF
MULTILOGO T
MULTILOGOBUTTERFLY
MULTILOGOFLGELGRIFF
The Valve Marking System professional contractors use for ball valves where valve and system identi cation is requestedDas Rohrkennzeichnungs-System,das Pro -Installateure fr Kugelhhne verwenden
MULTILOGO
41QUALITY SINCE 1972
0400 SuitcaseKoffer
MULTILOGOOne of many products by IMT ARMATUREN that saves time and money for the installer. This concept of design and top quality is consistent in all IMT Armaturen.
MULTILOGOein Produkt, das dem Installateur Flexibilitt und Kosteneinsparung bringt; ein Synonym fr Qualitt und Funktionalitt, das die Philosophie der IMT Armaturen widerspiegelt.
The installer can use the marking pen to mark or even customize the handle inserts. The inserts can be pre-marked in the shop to save time in the eld or can be customized with company trademarks. The possibilities are endless. IMT also offers a variety of pre-marked inserts.With MULTILOGO the contractor can make a professional job.
The MULTILOGO marking system is sold in a handy suitcase with 20 round inserts and 20 long handle inserts in each ve standard colors and a marking pen. Enough tags for 100 valves.
Mit dem wasserfesten Beschriftungsstift kann der Installateur die Beschriftungsleisten selbst je nach Einsatz personalisieren oder sogar sein Firmenlogo anbringen. Der Fantasie sind keine Grenzen gesetzt. IMT ARMATUREN bietet auch vorgedruckte Standardleisten an.MULTILOGO erlaubt dem Installateur, eine professionelle Arbeit zu hinterlassen.
Das MULTILOGO Rohrkennzeichnungs-System wird in einem handlichen Koffer mit 20 Abdeckkappen und 20 Beschriftungsleisten in je 5 Farben und mit einem wasserfesten Beschriftungsstift geliefert. Ausreichend fr 100 Kugelhhne.
Blank Inserts Neutrale Beschriftungleisten
04200.RO red/rot
04200.BL blue/blau
04200.GR green/grn
04200.WE white/weiss
04200.GE yellow/gelb
Round Inserts Abdeckkappen
04100.RO red/rot
04100.BL blue/blau
04100.GR green/grn
04100.WE white/weiss
04100.GE yellow/gelb
Pre-marked Inserts Bedruckte Beschriftungsleisten
Heizung Vorlauf 04200.RO01 red/rot
Heizung Rcklauf 04200.BL02 blue/blau
Heizung Vorlauf EG 04200.RO03 red/rot
Heizung Rcklauf EG 04200.BL04 blue/blau
Heizung Vorlauf 1.OG 04200.RO05 red/rot
Heizung Rcklauf 1.OG 04200.BL06 blue/blau
Warmwasser 04200.RO07 red/rot
Kaltwasser 04200.GR08 green/grn
Zirkulation 04200.WE09 white/weiss
Kaltwasser Garten 04200.GR10 green/grn
Fussbodenheizung Vorlauf 04200.RO11 red/rot
Fussbodenheizung Rcklauf 04200.BL12 blue/blau
Heizung Radiatoren Vorlauf 04200.RO13 red/rot
Heizung Radiatoren Rcklauf 04200.BL14 blue/blau
Gas 04200.GE15 yellow/gelb
Marking Pen Beschriftungsstift
04400 red/rot
42 QUALITY SINCE 1972
594 High-Temperature-Ball ValveDIN-DVGW for Gas and Potable WaterHochtemperatur-KugelhahnDIN-DVGW fr Gas und Trinkwasser
Besonders geeignet fr Heizkessel, die mit festen Brennstoffen wie Pellets und Hackschnitzel beheizt werden, sowie fr Fernwrme-Anlagenund Dampf
Druck: MOP 5 (5 bar) Gas PN 40 Wasser von 1/4 bis 2 * PN 25 Wasser 2 1/2 und 3 * PN 20 Wasser 4 * PN 10 Trinkwasser bis 2 *
Maximale Temperatur 150C Wasser (je nach Druck)Min. / max. Umgebungstemperatur bei Gas -20C bis 60C
Pressmessing gelbVoller DurchgangGewinde nach ISO 7Ausblassichere SpindelVerchromte KugelDIN-DVGW zerti ziert von 1/4 bis 2
Ausfhrungen: Art. 594 FF M Innen- x Innengewinde mit Designgriff MULTILOGOArt. 594 FF MT Innen- x Innengewinde mit Designgriff MULTILOGO TArt. 594 FF MF Innen- x Innengewinde mit Designgriff MULTILOGO FlgelArt. 594 FF Innen- x Innengewinde mit Aluminium GriffArt. 594 MF Innen- x Aussengewinde mit Aluminium GriffArt. 594 SSG Innen- x Innengewinde mit SanftschlussgriffArt. 594 ECO Ecobrass mit grnem Aluminium Griff
* 18C Wasser
Particularly suitable for solid-fuel- red Boilers, district Heatingand Steam
Pressure Rating: MOP 5 (72,5 psi) gas PN 40 (580 psi) water from 1/4 to 2 * PN 25 (362,5 psi) water 2 1/2 and 3 * PN 20 (290 psi) water 4 * PN 10 (145 psi) potable water to 2 *
Temperature Rating max. 150C (302F) water (depending on pressure)Min. / max. ambient Temperature -20C to 60C (-4F to 140F) gas Brass BodyFull Port OpeningThreaded Ends according to ISO 7Blow Out Proof StemChrome Plated BallDIN-DVGW certi ed from 1/4 to 2
Available in: Fig. 594 FF M Female Ends with MULTILOGO Handle Fig. 594 FF MT Female Ends with MULTILOGO T-HandleFig. 594 FF MF Female Ends with MULTILOGO Butter y-HandleFig. 594 FF Female Ends with Aluminium HandleFig. 594 MF Male / Female Ends with Aluminium HandleFig. 594 SSG Female Ends with Slow-Motion HandleFig. 594 ECO Ecobrass with green Aluminium Handle
* 18C (64,4F) water
The design 594 is also available from to 2 in ECOBRASS alloy. This alloy is lead free and contains no substances which may be dangerous for human health. It has better resistance against corrosion.
Kugelhahnserie Art. 594 ist von 1/2 bis 2 ist auch aus ECOBRASS Legierung lieferbar. Diese Legierung ist bleifrei und beinhaltet keine gesundheitsschdlichen Stoffe; sie hat bessere Bestndigkeit gegen Korrosion.
ROSTECHNADZOR(GGTN)
1 Cu Zn 40 Pb 2 - DIN EN 12165
2 3/8 - 1 Cu Zn 39 Pb 3 - DIN EN 121641 1/4- 2 Cu Zn 40 Pb 2 - DIN EN 12165
3 PTFE
4 Cu Zn 40 Pb 2 - DIN EN 12165
5 Viton 75 Shore
6 Cu Zn 39 Pb 3 - DIN EN 12164
7 Aluminium Al Si 11 Cu 2 (Fe)
8 Polyethylene - Polythylen
9 Steel, zinc plated - Stahl, verzinkt
10 Polypropylene - Polypropylen
1 VALVE BODY / KRPER
2 SEAT RING / KUGELDICHTUNG
3 BALL / KUGEL
4 RETAINER-BODY END / EINSCHRAUBTEIL
5 STEM / SPINDEL
6 O RING / O-RING
7 HANDLE / GRIFF
8 HANDLE SCREW / SCHRAUBEBall
Valv
es K
UG
ELH
H
NE
43QUALITY SINCE 1972
Female Ends with MULTILOGO Handle (see also page 40)Innen- x Innengewinde mit Designgriff MULTILOGO (siehe auch Seite 40)
Female Ends with MULTILOGO T-Handle (see also page 40)Innen- x Innengewinde mit Designgriff MULTILOGO T (siehe auch Seite 40)
Female Ends with MULTILOGO Butter y-Handle (see also page 40)Innen- x Innengewinde mit Designgriff MULTILOGO Flgel (siehe auch Seite 40)
594 FF M
594 FF MT
594 FF MF
Rp D L L1 SW H W3/8 10 50 11,4 21 41 1001/2 15 62 15 26 48 1003/4 20 71 16,3 31 51 100
1 25 83 19,1 40 57 1201 1/4 32 98 21,4 50 63 1201 1/2 40 110 21,4 55 79 150
2 50 133 25,7 70 87 150
Dimensions in mmMasse in mm
Rp D L L1 SW H W3/8 10 50 11,4 21 62 841/2 15 62 15 26 68 843/4 20 71 16,3 31 72 84
1 25 83 19,1 40 82 871 1/4 32 98 21,4 50 87 87
Dimensions in mmMasse in mm
Rp D L L1 SW H W3/8 10 50 11,4 21 35 641/2 15 62 15 26 42 643/4 20 71 16,3 31 45 64
Dimensions in mmMasse in mm
44 QUALITY SINCE 1972
Female Ends with Aluminium HandleInnen- x Innengewinde mit Aluminum Griff
Male / Female Ends with Aluminium HandleInnen- x Aussengewinde mit Aluminum Griff
Female Ends with Slow-Motion Handle Innen- x Innengewinde mit Sanftschlussgriff
594 FF
594 MF
594 SSG
Rp D L L1 SW H W1/4 10 50 11 21 42 1003/8 10 50 11,4 21 42 1001/2 15 62 15 26 48 1003/4 20 71 16,3 31 51 100
1 25 83 19,1 40 59 1201 1/4 32 98 21,4 50 64 1201 1/2 40 110 21,4 55 85 150
2 50 133 25,7 70 93 1502 1/2 65 144 29 84 121 246
3 80 166 31 102 130 2464 90 195 35 127 139 246
Dimensions in mmMasse in mm
Rp D L L1 L3 SW H W3/8 10 58 11,4 10,1 21 42 1001/2 15 69 15 13,2 26 48 1003/4 20 77 16,3 14,5 31 51 100
1 25 90 19,1 16,8 40 59 1201 1/4 32 104 21,4 19,1 50 64 150
1 1/2 40 116 21,4 19,1 55 85 1502 50 141 25,7 23,4 70 93 150
Dimensions in mmMasse in mm
Rp D L L1 SW H1 W21/4 10 50 11 21 55 703/8 10 50 11,4 21 55 701/2 15 62 15 26 61 703/4 20 71 16,3 31 65 70
1 25 83 19,1 40 71 701 1/4 32 98 21,4 50 76 70
1 1/2 40 110 21,4 55 104 1132 50 133 25,7 70 112 113
Dimensions in mmMasse in mm
Ball
Valv
es K
UG
ELH
H
NE
45QUALITY SINCE 1972
Flanged Shut-off Valve with MULTILOGO T-HandlePumpen anschkugelhahn mit Designgriff MULTILOGO T
Flanged Shut-off Valve with Aluminium Butter y HandlePumpen anschkugelhahn mit Aluminium Flgelgriff
Flanged Shut-off Valve with Allen Key Pumpen anschkugelhahn mit Inbus-Schlssel
591 FFL MT
591 FFL
576 FFL
G G1 D L L1 SW SW1 H W1 1 1/2 25 72 15 38 51,5 82 87
Dimensions in mmMasse in mm
G G1 D L L1 SW SW1 H W1 1 1/2 25 72 15 38 51,5 82 87
Dimensions in mmMasse in mm
G G1 D L L1 SW SW11 1 1/2 20 50 15 51,5 5
Dimensions in mmMasse in mm
46 QUALITY SINCE 1972
492 Full Port Ball Valve DIN-DVGW Gas and Potable WaterKugelhahn mit vollem Durchgang DIN-DVGW Gas und Trinkwasser
Druck: MOP 5 (5 bar) Gas PN 40 Wasser * PN 10 Trinkwasser bis 2 *Maximale Temperatur 100C Wasser (ohne Dampf), (je nach Druck)Fr hhere Temperaturen und Dampf siehe Art. 594 auf Seite 42Min. / max. Umgebungstemperatur bei Gas 20C bis 60C
Pressmessing gelbVoller DurchgangGewinde nach ISO 7Ausblassichere SpindelVerchromte Kugel
Ausfhrungen: Art. 492 FF M Innen- x Innengewinde mit Designgriff MULTILOGOArt. 492 FF ST Innen- x Innengewinde mit gelbem Stahlgriff fr GasArt. 492 FF Innen- x Innengewinde mit rotem Aluminium GriffArt. 492 FF AG Innen- x Innengewinde mit grnem Aluminium Griff
* 18C Wasser
Pressure Rating: MOP 5 (72,5 psi) gas PN 40 (580 psi) water * PN 10 (145 psi) potable water to 2 *Temperature Rating max. 100C (212F) water (no steam), (depending on pressure) For higher Temperatures and steam see Fig. 594 on page 42Min. / max. ambient Temperature -20C to 60C (-4F to 140F) gas Brass BodyFull Port OpeningThreaded Ends according to ISO 7Blow Out Proof StemChrome Plated Ball
Available in: Fig. 492 FF M Female Ends with MULTILOGO Handle Fig. 492 FF ST Female Ends with yellow Steel Handle for gasFig. 492 FF Female Ends with red Aluminium HandleFig. 492 FF AG Female Ends with green Aluminium Handle
* 18C (64,4F) water
1 Cu Zn 40 Pb 2 - DIN EN 12165
2 1/2-1 Cu Zn 39 Pb 3 - DIN EN 12164 1 1/4-2 Cu Zn 40 Pb 2 - DIN EN 12165
3 PTFE
4 Cu Zn 40 Pb 2 - DIN EN 12165
5 Viton
6 Cu Zn 39 Pb 3 - DIN EN 12164
7 Steel, zinc plated - Stahl, verzinkt
8 Polyethylene - Polythylen
9 Polypropylene - Polypropylen
10 Aluminium Al Si 11 Cu 2 (Fe)
ROSTECHNADZOR(GGTN)
1 VALVE BODY / KRPER
2 SEAT RING / KUGELDICHTUNG
3 BALL / KUGEL
4 RETAINER-BODY END / EINSCHRAUBTEIL
5 STEM / SPINDEL
6 O RING / O-RING
7 HANDLE / GRIFF
8 HANDLE SCREW / SCHRAUBE
1
7
2
2
4
5
6
8
3Ball
Valv
es K
UG
ELH
H
NE
47QUALITY SINCE 1972
Female Ends with MULTILOGO Handle (see also page 40)Innen- x Innengewinde mit Designgriff MULTILOGO (siehe auch Seite 40)
Female Ends with yellow Steel Handle for gasInnen- x Innengewinde mit gelbem Stahlgriff fr Gas
Female Ends with red Aluminium Handle Innen- x Innengewinde mit rotem Aluminium Griff
Female Ends with green Aluminium Handle for Potable WaterInnen- x Innengewinde mit grnem Aluminium Griff fr Trinkwasser
492 FF M
492 FF ST
492 FF
492 FF AG
Rp D L L1 SW H W1/2 15 58 15 25 44 1003/4 20 68 16,3 31 48 100
1 25 80 19,1 38 52 1001 1/4 32 94 21,4 47 62 1201 1/2 40 103 21,4 53 67 120
2 50 126 25,7 66 85 150
Dimensions in mmMasse in mm
Rp D L L1 SW H W1/2 15 58 15 25 45 853/4 20 68 16,3 31 48 85
1 25 80 19,1 38 52 851 1/4 32 94 21,4 47 64 1101 1/2 40 103 21,4 53 69 110
2 50 126 25,7 66 91 135
Dimensions in mmMasse in mm
Rp D L L1 SW H W1/2 15 58 15 25 45 853/4 20 68 16,3 31 48 85
1 25 80 19,1 38 52 851 1/4 32 94 21,4 47 64 1101 1/2 40 103 21,4 53 69 110
2 50 126 25,7 66 91 135
Dimensions in mmMasse in mm
Rp D L L1 SW H W1/2 15 58 15 25 42 853/4 20 68 16,3 31 46 85
1 25 80 19,1 38 50 851 1/4 32 94 21,4 47 64 1101 1/2 40 103 21,4 53 69 110
2 50 126 25,7 66 88 135
Dimensions in mmMasse in mm
48 QUALITY SINCE 1972
583 Full Port Ball Valve DIN-DVGW Potable WaterKugelhahn mit vollem Durchgang DIN-DVGW Trinkwasser
Druck: PN 40 Wasser *PN 10 Trinkwasser *Maximale Temperatur 100C Wasser (ohne Dampf), (je nach Druck)Fr hhere Temperaturen und Dampf siehe Art. 594 auf Seite 42Pressmessing gelbVoller DurchgangGewinde nach ISO 7Ausblassichere SpindelVerchromte Kugel
Ausfhrungen: Art. 583 FF Innen- x Innengewinde mit grnem Florida Griff fr Trinkwasser
* 18C Wasser
Pressure Rating:PN 40 (580 psi) water *PN 10 (145 psi) potable water *Temperature Rating max. 100C (212F) water (no steam), (depending on pressure)For higher Temperatures and steam see Fig. 594 on page 42Brass BodyFull Po