Introduc The D anGroen Mattachingmechanisand instrof orienticover. 1.0 R 1.1 Uhardware
1.2 R
ction:
nd DL Tiltingodel D or DL
g the hinge msm, a “U” shructions for fng the cove
Riser Bracke
Unpack the ce.
Remove the f
IN
P
g Kettle PowL Kettle. Thmechanism ahaped riser, ield installatr on top of th
et Installatio
cover and co
four hole plu
NSTRUC
D and DPower-Aid
Assemb
er-Aid Covehe kits includand a bent rand a hardwion. The insthe kettle and
on
omponents a
ug caps in th
Page 1
CTION S
DL Tilting Kd (#51) Cobly and Moun
r Kits are shde a spun starod handle, aware kit with tructions beld securing th
and locate th
he left trunnio
SHEET
Kettle over Kit nting
hipped compainless steela spring-assitems needelow will guidhe assembly
he U-shaped
on plate.
plete for fieldl disk cover
sisted power ed for attach
de you througy bracket to t
d riser bracke
146551 Re
d installation with studs foaid hinge
hing the covegh the procethe pedesta
et and moun
ev. B
on a or
er ess l
nting
1.3 A
1.4 Alock wasnuts to a
Align the rise
Align the holehers and nu20 ft/lb torq
r to the hole
es in the risets to secureue with a 3/
es in the trun
er bracket to the bracket8” open end
Page 2
nnion plate a
the cover at to the coved or socket w
as shown.
s shown ander, gasket anwrench.
d install the nd backing p
146551 Re
mounting bolate. Tighte
ev. B
olts, en the
2.0 A 2.1 AAssemblenough f
2.2 Alocking cin/lb torq
Actuator and
Align the stude the fenderfor adjustme
Assemble thecompound anue with a 1/4
d Cover Ins
ds on the covr washers an
ent.
e actuator tond the dome4” open end
tallation an
ver actuatornd nuts to th
o the three ste nuts suppli or socket w
Page 3
nd Adjustme
r to the holese underside
tuds on the ded in the co
wrench.
ent
s in the top oe of the actua
domed coveover kit. Tigh
of the riser bator, but leav
er and securhten the dom
146551 Re
bracket. ve them loos
re using threme nuts to 20
ev. B
se
ead 0
2.3 Ekettle. Adfour nutswrench.
2.4 Inlocking c
2.5 Aa 20 ft/lb
Ensure the kedjust the mos securing th
nstall the hancompound to
Attach the hatorque and
ettle is tilted unting bracke actuator to
ndle spacerso the ends of
andle over ththen install t
to the full upket to align to the riser to
s over the twf the two stu
he spacers athe red ball
Page 4
pright positiohe cover ove
o a 10 ft/lb to
wo studs at tds.
and secure won the hand
on and then er the kettle orque with a
the front of th
with two domdle end.
lower the coand then fu1/4” open e
he cover and
me nuts. Tig
146551 Re
over over theully tighten thend or socke
d apply thre
hten the nut
ev. B
e he et
ad
ts to
2.6 Atwo 3/4”
2.7 T
Adjust the tenopen end w
The complete
nsion in the renches.
ed Power-Ai
actuator ass
d cover asse
Page 5
sembly by tu
embly shoul
urning the ad
d look as sh
djusting nuts
hown below:
146551 Re
s as shown.
ev. B
Use
146551 Rev. B Page 6
1055 Mendell Davis Drive, Jackson, MS 39272 • 888.994.7636 • 888.864.7636 • unifiedbrands.net ADDITIONAL MANUFACTURING LOCATION: 525 SOUTH COLDWATER ROAD, WEIDMAN MI 48893
© 2009 Unified Brands. All Rights Reserved. Unified Brands is a wholly-owned subsidiary of Dover Corporation.