32
11G Effective Date: December, 2004 Industrial Grinders, Buffers, Accessories & Replacement Parts
11G
Effective Date:December, 2004
Industrial Grinders,Buffers, Accessories& Replacement Parts
Baldor’s Mission Statement
To be the best(as determined by our customers)
marketers, designers, and manufacturersof electric motors, drives and generators.
1
TABLE OF CONTENTS
Bench and Pedestal Grinders
6 Inch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 6 Inch Deluxe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 7 Inch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 7 Inch Deluxe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 8 Inch Industrial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 8 Inch Industrial Deluxe. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 10 Inch Industrial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 10 Inch Industrial Deluxe. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 12 Inch Heavy Duty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 14 Inch Heavy Duty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Tool Grinders
6 Inch Diamond Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 6 Inch Carbide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Wheels and Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Belt Grinders and Buffers
Industrial Abrasive - Three Position Tiltable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Stationary Abrasive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Industrial Buffers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Big Red Grinders
6 Inch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 7 Inch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 8 Inch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Pedestals and Lighted Eyeshields. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-17
Mod Express TM Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-19
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-28
Abrasive Belt Grinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Belt Grinders. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-25 Carbide and Diamond Wheel Grinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Dust Control Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Eyeshields and Pedestals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Grinders 6" and 7" – Buffers – 1/4 Hp and 1/3 Hp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Grinders 8", 10", 12" and 14" – Buffers – 3/4 Hp thru 10 Hp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Pedestals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Baldor District Offices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
FULL 3 YEAR WARRANTY
ALL BALDOR GRINDER AND BUFFER PRODUCTS WARRANTED THREE FULL YEARSBaldor grinder and buffer products are warranted against burnouts, defective materials, and workmanship for three full years.
Warranty covers all parts except those subject to normal wear such as wheels.
PRICES ARE SUBJECT TO CHANGE WITHOUT NOTICE
2
600E Series Grinder – Grinder/BufferTwo wheels 6"x3/4"x1/2". Guards – cast aluminum with gated external ports.
Furnished with GA13 plexiglas eyeshields.
6 INCHTwo wheels 6” x 3/4” x 1/2”. Guards are non-exhaust type.
Furnished with GA10 eyeshields.
CatalogNumber
Unit 1List
PriceHp Volts 2
IdleRPM
ShippingWeight
600E Grinder 179 1/3 115 3600 29
602E Grinder/Buffer 179 1/3 115 3600 28
612 346 Grinder 203 1/3 115 3600 30
662 346 Grinder/Buffer 203 1/3 115 3600 29
6 INCH DELUXETwo wheels 6” x 3/4” x 1/2”. Guards are cast iron, exhaust type. Furnished with GA10 eyeshields.
CatalogNumber
Unit 1List
PriceHp Volts 2
IdleRPM
ShippingWeight
612E 346 Grinder 252 1/3 115 3600 44
623E 35 Grinder 285 1/3 115 3600 47
623ED 57 Grinder 386 1/3 115 3600 61
632E 5 Grinder 285 1/4 115 1800 47
662E 346 Grinder/Buffer 252 1/3 115 3600 43
673E 35 Grinder/Buffer 285 1/3 115 3600 47
Industrial Grinders
600E
612E
3
7 INCH Two Wheels 7” x 1” x 5/8”. 1/2 Hp.All units supplied with non-lighted eyeshields.
CatalogNumber
Unit 1List
PricePhase Volts 2
IdleRPM
ShippingWeight
712 346 Grinder 300 1 115 3600 45
762 346 Grinder/Buffer 300 1 115 3600 44
712E 345 Grinder 355 1 115 3600 69
762E 346 Grinder/Buffer 355 1 115 3600 68
7306 35 Grinder 388 1 115/230 1800 71
7307 35 Grinder 388 1 115/230 3600 70
7351 35 Grinder/Buffer 388 1 115/230 3600 68
7308 345 Grinder 388 3 208-230/460 1800 71
7309 345 Grinder 388 3 208-230/460 3600 72
CatalogNumber
Unit 1 List
PricePhase Volts 2
IdleRPM
ShippingWeight
7306D 37 Grinder 501 1 115/230 1800 84
7307D 37 Grinder 501 1 115/230 3600 83
7309D 347 Grinder 501 3 208-230/460 3600 87
7312D 37 Grinder 630 1 115 1800/3600 90
NOTES: 1 Grinders supplied with one 36 grit and one 60 grit grinding wheel. Grinder/Buffers supplied with one 36 grit grinding wheel and one wire brush wheel 0.014 wire.
2 115 volt and 115/230 volt, single phase, 60 hertz units are supplied with start/stop switch, 8 foot 3 conductor cord with plug connected for 115 volts. 115/230 volt units are reconnectable for 230 volts with plug change.
208-230/460 volt, 3 phase, 50/60 hertz units supplied with start/stop switch factory connected for 208-230 volts, reconnectable for 460 volts. No cord and plug supplied.
3 U.L. Listed. 4 C.S.A. Certified 5 Supplied with cast iron tool rests and exhaust type guards. 6 Supplied with pressed steel tool rests and cast aluminum non-exhaust type guards except 612E, 662E, 712E and 762E which have cast
iron exhaust type guards. 7 Supplied with #GA24 water pot, #GA25 tool tray, and 2 #GA9 lighted eyeshields wired through the start/stop switch of the single phase
units only. Light bulbs are not supplied. Rough service bulbs, max. 60 watts are suggested. All 208-230/460 volt 3 phase grinders and buffers are suitable for 50 or 60 Hz. See pages 18 & 19 for optional controls. Designed to comply with OSHA standards under normal usage.
7 INCH DELUXE Two Grinding Wheels: 7” x 1” x 5/8”. 1/2 Hp. 7312D is two speed rated 1/3 and 1/2 Hp.
Guards are cast iron, exhaust type. Supplied with cast iron rests and GA9 lighted eye shields.
Industrial Grinders
712
7306D
4
NOTES: 1 Grinders supplied with one 36 grit and one 60 grit grinding wheel. Grinder/Buffers supplied with one 36 grit grinding wheel and one wire brush wheel 0.014 wire.
2 115/230 volt are single phase, 60 hertz. Units supplied with start/stop switch, 8 foot 3 conductor cord with plug connected for 115 volts. Reconnectable for 230 volts with a plug change. 208-230/460 volt are three phase, 50/60 hertz units supplied with start/stop switch factory connected for 208-230 volts. Reconnectable for 460 volts, 575 volt units are single voltage. !022W, 1022WD, and 3 phase units supplied less cord and plug.
3 U.L. Listed.
4 C.S.A. Certified
5 Supplied with GA24 water pot, GA25 tool tray, and two GA9 lighted eyeshields wired through the start/stop switch of single phase units only. Light bulbs are not supplied. Rough service bulbs, max. 60 watts are suggested.
Designed to comply with OSHA standards under normal usage.
CatalogNumber
Unit 1List
PriceHp Volts 2
IdleRPM
ShippingWeight
8100W 3 Grinder 626 3/4 115/230 1800 99
8107W 3 Grinder 626 3/4 115/230 3600 99
8250W 3 Grinder/Buffer 626 3/4 115/230 3600 97
8102W 34 Grinder 607 3/4 208-230/460 1800 98
8123W 34 Grinder 607 3/4 208-230/460 3600 99
8252W Grinder/Buffer 607 3/4 208-230/460 3600 95
8125W 3 Grinder 607 3/4 575 3600 99
8 INCH INDUSTRIALTwo wheels 8”x 1”x 3/4”. Guards are cast iron exhaust type. Supplied with cast iron tool rests and GA11 eyeshields.
CatalogNumber
Unit 1List
PriceHp Volts 2
IdleRPM
ShippingWeight
8100WD 35 Grinder 716 3/4 115/230 1800 110
8107WD 35 Grinder 716 3/4 115/230 3600 111
8102WD 345 Grinder 705 3/4 208-230/460 1800 111
8123WD 345 Grinder 705 3/4 208-230/460 3600 112
8 INCH INDUSTRIAL DELUXETwo Wheels 8” x 1” x 3/4”. Guards are cast iron, exhaust type. Supplied with cast iron tool rests and GA9 lighted eyeshields.
Industrial Grinders
8100W
8100WD
5
CatalogNumber
Unit 1List
PriceHp Volts 2
IdleRPM
ShippingWeight
1022W 3 Grinder 800 1 115/230 1800 133
1021W 34 Grinder 789 1-1/2 208-230/460 1800 134
105W 34 Grinder 789 1-1/2 575 1800 133
10 INCH INDUSTRIAL Two wheels 10” x 1” x 7/8”. Guards are cast iron exhaust type. Supplied with cast iron tool rests and GA11 eyeshields.
CatalogNumber
Unit 1List
PriceHp Volts 2
IdleRPM
ShippingWeight
1022WD 35 Grinder 917 1 115/230 1800 145
1021WD 345 Grinder 904 1-1/2 208-230/460 1800 146
10 INCH INDUSTRIAL DELUXE Two Wheels: 10” x 1” x 7/8”. Guards are cast iron, exhaust type. Supplied with cast iron tool rests and GA9 lighted eyeshields.
NOTES: 1 Grinders supplied with one 36 grit and one 60 grit grinding wheel. Grinder/Buffers supplied with one 36 grit grinding wheel and one wire brush wheel 0.014 wire.
2 115/230 volt are single phase, 60 hertz. Units supplied with start/stop switch, 8 foot 3 conductor cord with plug connected for 115 volts. Reconnectable for 230 volts with a plug change. 208-230/460 volt are three phase, 50/60 hertz units supplied with start/stop switch factory connected for 208-230 volts. Reconnectable for 460 volts, 575 volt units are single voltage. 1022W, 1022WD, and 3 phase units supplied less cord and plug.
3 U.L. Listed.
4 C.S.A. Certified
5 Supplied with GA24 water pot, GA25 tool tray, and two GA9 lighted eyeshields wired through the start/stop switch of single phase units only. Light bulbs are not supplied. Rough service bulbs, max. 60 watts are suggested.
Designed to comply with OSHA standards under normal usage.
Industrial Grinders
1022W
1022WD
6
Industrial Grinders
12 INCH HEAVY DUTYArbor 1-1/4” accommodates 2” wide wheels. Guards are cast iron, exhaust type. All units1800 idle RPM. Price includes manual starter and GA9 lighted eyeshields, but does not include wheels, light bulbs, or pedestal. (Specify voltage when ordering.)
NOTE: Manual starter provides overload protection. (3 phase suitable for 50/60 Hz, single phase 60 Hz)
WHEELS FOR 12 INCH GRINDERS
CatalogNumber
List PriceLess Wheels& Pedestal
Hp VoltsFactory
ConnectedVoltage
PhaseShippingWeight
1215W 1803 2 208-230/460 230 3 253
1216W 1866 3 208-230/460 230 3 254
1217W 1909 2 115/230 230 1 259
129W 1866 3 575 575 3 256
CatalogNumber
ListPrice
Diameter Face Bore GritShippingWeight
B125 106 12” 2” 1-1/4” 30 22
B126 106 12” 2” 1-1/4” 46 22
NOTES: Wheels are aluminum oxide, medium grade, vitrified bond. When installing new wheels, check wheel for possible damage. Do not use a damaged wheel.
Wear safety glasses. With new wheel installed, all safety guards in place and operator standing away from front of grinder, run grinder for one minute before applying work.
Exercise caution.
Designed to comply with OSHA standards under normal usage.
1215W with GA20 Pedestal
7
14 INCH HEAVY DUTYArbor 1-1/4” accommodates 3” wide wheels. Guards are cast iron, exhaust type. All units 50/60 Hz, 1500/1800 idle RPM, three phase. Price includes starter and GA9 lighted eyeshields, but does not include wheels, light bulbs, or pedestal.
WHEELS FOR 14 INCH GRINDERS
CatalogNumber
List PriceLess Wheels& Pedestal
Hp Volts
StarterProvidesOverload
Protection
ShippingWeight
1406W 2314 5 230 Magnetic 359
1410W 2314 5 460 Magnetic 362
1408W 2314 5 575 Magnetic 358
1407W 2524 7-1/2 230 Magnetic 372
1411W 2524 7-1/2 460 Magnetic 381
1409W 2524 7-1/2 575 Magnetic 374
CatalogNumber
ListPrice
Diameter Face Bore GritShippingWeight
B147 200 14” 3” 1-1/4” 30 42
B148 200 14” 3” 1-1/4” 46 41
NOTES: Wheels are aluminum oxide, medium grade, vitrified bond. When installing new wheels, check wheel for possible damage. Do not use a damaged wheel.
Wear safety glasses. With new wheel installed, all safety guards in place and operator standing away from front of grinder, run grinder for one minute before applying work.
Exercise caution.
Designed to comply with OSHA standards under normal usage.
1407Wwith GA20 Pedestal
Industrial Grinders
8
Industrial Tool Grinders
CatalogNumber
ListPrice
Face GritShippingWeight
Description
D501 448 3/4" 120 2 General Purpose Diamond Wheel
D502 448 3/4" 220 2 Fine Finish Diamond Wheel
CatalogNumber
List PriceLess Wheels
Volts PhaseShippingWeight
522 ✧ * 1007 115 1 108
532 ✧ ** 1007 203-230/460 3 109
6 INCH DIAMOND WHEEL TOOL GRINDER1/2 Hp, 3600 Idle RPM, 60 Hz
DIAMOND WHEELS
NOTES: 6" diameter, 1-1/4" center hole – 1/16" abrasive depth.
When installing new wheels, check wheel for possible damage. Do not use a damaged wheel.
Wear safety glasses. With new wheel installed and all safety guards in place and operator standing away from front of grinder, run grinder for one minute before applying work.
Exercise caution.
UnderwritersLaboratoryListed
522
NOTES: Prices include all parts pictured except wheels and bulb for lamp. Rough service bulb is suggested. Locked double row bearings. Guaranteed maximum .002 runout on face at periphery.
* Supplied with reversing switch, eight foot, three conductor cord and plug. ** Supplied with reversing switch but less cord and plug, connected at factory for 208-230 volts. ✧ Not CSA Certified.
D501 and D502
9
C61
NOTES: GA8 Dresser accommodates Diamond Tool NIB 7/16" diameter 1" long.
When installing new wheels, check wheel for possible damage. Do not use a damaged wheel.
Wear safety glasses. With new wheel installed and all safety guards in place and operator standing away from front of grinder, run grinder for one minute before applying work.
Exercise caution.
UnderwritersLaboratoryListed
500
CatalogNumber
List PriceLess Wheels
Volts PhaseShippingWeight
500 ✧* 897 115 1 109
510 ✧** 897 203-230/460 3 109
6 INCH CARBIDE TOOL GRINDER1/2 Hp, 3600 Idle RPM, 60 Hz
NOTES: Prices include all parts pictured except wheels and bulb for lamp. Rough service bulb is suggested. Grinder accommodates cup wheels 6" diameter 1" face, recessed 4" dia. 1 1/2" deep, steel backed 1-1/4" center hole.
* Supplied with reversing switch, eight foot, three conductor cord and plug. ** Supplied with reversing switch but less cord and plug, connected at factory for 208-230 volts. ✧ Not CSA Certified.
CatalogNumber
ListPrice
Face GritShippingWeight
Description
C61 67 1” 60 3 Silicone Carbide
C121 67 1” 120 3 Silicone Carbide
S46 61 1” 46 3 Aluminum Oxide
S61 61 1” 60 3 Aluminum Oxide
GA8 74 Wheel Dresser with Diamond NIB
GA7 44 Diamond NIB for GA8 – 7/16" diameter – 1" long
WHEELS AND ACCESSORIES
Industrial Tool Grinders
10
Catalog Number
ListPrice
VoltsIdle RPM
PhaseShippingWeight
248-151TD * 1057 115/230 3600 1 95
248-153TD ** 1025 208-230/460 3600 3 84
248-181TD ♦*** 1241 115/230 3600 1 138
248-183TD ♦** 1207 208-230/460 3600 3 128
248-151AS † 1139 115 0-3600 1 105
STATIONARY ABRASIVE BELT GRINDER
2048-151D * 965 115/230 3600 1 88
2048-153D ** 933 208-230/460 3600 3 76
UnderwritersLaboratoryListed
INDUSTRIAL ABRASIVE BELT GRINDER – THREE POSITION TILTABLE1 1/2 hp, 60 Hz, Single and Three Phase
NOTES: Belt size 2" x 48" – 80 grit. ♦ Supplied with 8" x 1" x 3/4" – 36 grit grinding wheel and 2" x 48" – 80 grit belt. * Supplied with start/stop switch, eight foot, three conductor cord and plug, connected for 115 volts – U.L. Listed. ** Supplied with start/stop switch connected for 208-230 volts, but less cord and plug. U.L. Listed. *** Supplied with start/stop switch, connected for 115 volts but less cord and plug. Not. U.L. Listed or C.S.A. Certified. † Supplied with Adjustable Speed Control, start/stop switch, eight foot, three conductor cord and plug. Not U.L. Listed or C.S.A. Certified.
2048-151D 248-181TD 248-151TD 248-151AS
Industrial Abrasive Belt GrindersThe ULTIMATE In Grinding Flexibility
11
NOTES: Prices do not include pedestal. * Supplied with eight foot, three conductor cord, plug and switch connected at factory for 115 volts ** Supplied with start/stop switch connected for 208-230 volts less cord and plug ◆ Supplied with switch less cord and plug. Connected at factory for 115 volts †* Supplied with manual starter, connected at factory for 230 volts. Specify voltage when ordering †† Supplied with magnetic starter, connected at factory for 230 volts. Specify voltage when ordering
Buffers are designed for use with soft cloth wheels ONLY. Specific buffing applications may require the addition of operator safety devices. Consult with a safety engineer before installation. Prices include flanges and nuts but do not include wheels. Single phase buffers 60 Hz, 115/230 volts, except #114 and #111 which are 115 volts. All three phase buffers 50/60 Hz, 208-230/460 volts must be connected for specific voltage. Buffers supplied less wheels.
CatalogNumber
ListPrice
Hp PhaseIdleRPM
ShaftDiameter
WheelShippingWeightDiameter
Max.Width
Min/Max
114 * 227 1/4 1 1800 1/2” 6” 0.5/0.75 24
111 * 227 1/3 1 3600 1/2” 6” 0.5/0.75 25
332B * 448 3/4 1 1800 3/4” 8” 0.38/1.25 55
333B * 448 3/4 1 3600 3/4” 8” 0.38/1.25 56
334B ** 437 3/4 3 1800 3/4” 8” 0.38/1.25 54
330B ** 437 3/4 3 3600 3/4” 8” 0.38/1.25 56
407B ◆ 594 1 1 1800 7/8” 10” 0.5/1.25 60
410B ◆ 584 1-1/2 1 3600 7/8” 10” 0.5/1.25 61
409B ** 571 1-1/2 3 1800 7/8” 10” 0.5/1.25 59
412B ** 571 1-1/2 3 3600 7/8” 10” 0.5/1.25 62
1250 †* 1379 2 1 1800 1-1/4” 12” 2.0/2.5 164
1251 †* 1339 2 1 3600 1-1/4” 12” 2.0/2.5 160
1252 †* 1265 3 3 1800 1-1/4” 12” 2.0/2.5 156
1253 †* 1230 3 3 3600 1-1/4” 12” 2.0/2.5 156
1457 †† 1849 5 3 1200 1-1/4” 14” 2.5/3.0 228
1458 †† 1574 5 3 1800 1-1/4” 14” 2.5/3.0 218
1454 †† 1759 7-1/2 3 1800 1-1/4” 14” 2.5/3.0 229
1453 †† 1662 7-1/2 3 3600 1-1/4” 14” 2.5/3.0 223
333B 1252with GA20 Pedestal
Industrial Buffers
12
Catalog Number Unit List Price Hp Idle RPM Shipping Weight
712R † Grinder 300 1/2 3600 46
762R † Gr/Buffer 300 1/2 3600 43
712RE * Grinder 355 1/2 3600 70
762RE * Gr/Buffer 355 1/2 3600 67
600RE Series Grinder – Grinder/BufferTwo wheels 6"x3/4"x1/2". Guards – cast aluminum with gated external ports.
Furnished with GA13 plexiglas eyeshields.
6 INCH GRINDERS – 6" x 3/4" x 1/2"115 Volts, Single Phase, 60 Hz – Guards are non-exhaust type.
Grinder supplied with two grinding wheels 6” x 3/4” x 1/2”, one 36 grit and one 60 grit.Gr/Buffer supplied with one 36 grit grinding wheel and one wire brush wheel. 0.014 wire.
Catalog Number Unit List Price Hp Idle RPM Shipping Weight
600RE Grinder 179 1/3 3600 29
602RE Gr/Buffer 179 1/3 3600 28
612R* Grinder 203 1/3 3600 30
662R* Gr/Buffer 203 1/3 3600 29
NOTES: Supplied with eight foot, three conductor cord and plug. * Furnished with GA10 eyeshields and pressed steel tool rests and supports.
7 INCH GRINDERS – 7" x 1" x 5/8"115 Volts, Single Phase, 60 Hz.
Grinder supplied with two grinding wheels 7” x 1” x 5/8”, one 36 grit and one 60 grit.
Grinder/Buffer supplied with one 36 grit grinding wheel and one wire brush wheel 0.014 wire.
NOTES: Supplied with eight foot, three conductor cord and plug. Furnished with pressed steel tool rests and supports. * Furnished with GA11 eyeshields and cast iron exhaust type guards. † Guards are non-exhaust type. Supplied with GA10 eyeshields.
712R
612R
Big Red GrindersDESIGNED TO MEET OSHA STANDARDS – U.L. LISTED AND CSA CERTIFIED
Identical to Baldor’s Industrial Gray Grinder/Buffer Line,these Baldor Grinders/Buffers and Accessories are painted Red.
600RE
13
GA9RFits Baldor grinders 6" - 14"
Supplied less bulbs, rough service bulbs are suggested
Accommodates 60 watt bulb
Shipping Weight 5 lbs
List Price $91.00 each pair
GA14R PEDESTALFor 6", 7", 8" grinders and grinder buffers
Fabricated steel
Height 34-1/2"
Shipping Weight 64 lbs.
List Price $165.00
GA9SRSame as GA9R except with On and Off Switch
U.L. Component Recognized
CSA Certified
Shipping Weight 6 lbs.
List Price $101.00 each pair
LIGHTED EYESHIELDS
GA16R PEDESTALFor 6", 7", 8" grinders and grinder / buffers. Height 32-7/8"
Base 15 3/4" wide x 14" deep
Shipping Weight 61 lbs.
List Price $219.00
Big Red Grinders
CatalogNumber
UnitList
PriceHp
IdleRPM
ShippingWeight
812RE ♦ Grinder 593 3/4 3600 99
862RE ♦ Gr/Buffer 593 3/4 3600 95
8 INCH GRINDERS – 8" x 1" x 3/4"115/230 Volts, Single Phase, 60 Hz
Guards are cast iron exhaust type.
Grinder supplied with two grinding wheels 8” x 1” x 3/4”, one 36 grit and one 60 grit.
Grinder/Buffer supplied with one 36 grit grinding wheel and one wire brush wheel 0.014 wire.
NOTES: Supplied with eight foot, three conductor cord and plug, connected at factory for 115 volts. Furnished with GA11 eyeshields, pressed steel tool rests and supports. ♦ Not CSA Certified.
812RE
DESIGNED TO MEET OSHA STANDARDS – U.L. LISTED AND CSA CERTIFIEDIdentical to Baldor’s Industrial Gray Grinder/Buffer Line,
these Baldor Grinders/Buffers and Accessories are painted Red.
14
CatalogNumber
DustControl
UnitPrice
GrindingWheel
Maximum
Cubic Ft/MinAir
ControlValves
ShippingWeight Total
Capacity
RequiredPer WheelBy OSHA*Diameter Width
DC7 660 7” 1” 440 220 Yes 60
DC8 660 8” 1” 440 220 Yes 60
DC10 660 10” 1” 440 390 Yes ** 60
DC12 719 12” 2” 440 390 Yes ** 62
DC12-3 719 12" 2" 440 390 Yes ** 62
DC14-3 + 1174 14” 3” 700 590 Yes ** 73
REPLACEMENT FILTER BAGS
Catalog Number List Price Dust Control Unit
ARB-1 44 DC7, 8, 10, 12
ARB-2 61 DC14-3
DUST CONTROL UNITSFOR BALDOR GRINDERS
115 Volt, Single Phase, 60 Hz
Accessories
1022Wwith DC10 and GA16
NOTES: * DB rating – 83, “A” scale weighing – taken at operator
** Air control valve required to direct total CFM of collector to only the wheel being used to meet OSHA CFM requirements on 10” and larger grinders.
* From Ventilation Section 1910.94 Table G-4 Federal Register Vol. 37 #202, 10-18-72:
Do not collect potentially reactive materials without consulting (NFPA) National Fire Protection Association Standards.Powered by a 1/2 hp TEFC single phase Baldor motor with cord, switch, and plug. 230 volt single phase units available and supplied less switch, cord, and plug. Specify for 230 volt single phase operation.Add $30.00 to list price.Collectors with three phase motor less cord, switch, and plug are available.For 208-230/460 volt three phase, add suffix -3 to catalog number.Add $30.00 to list price. Mount dust control units with Grinder and GA16 or GA20 pedestal.
+ DC14-3 powered with 1Hp TEFC 208-230/460 volt, three phase motor, less cord, switch, and plug.
15
Item Number Description 13List Price Shipping Weight
A GA16 Pedestal Cast Iron 219 62A GA16E Pedestal Steel 141 36B GA14 Pedestal 165 64C GA20 Pedestal Gast Iron 361 125C GA20E Pedestal Steel 165 54D GA24 Water Pot 22 2E GA3 Water Pot 36 7F GA25 Tool Tray 23 4G GA4 Tool Tray 36 6H GA11 Eyeshield 28 pr 2I GA10 Eyeshield 25 pr 2J GA9 Lighted Eyeshield (less on/off switch) 91 pr 5
J-1 GA9-1 same as GA9 except packed 1 unit per carton 49 ea 3K GA9S Lighted Eyeshield (with on/off switch) 101 pr 6L GA13 Eyeshield for 6" Grinders 21 pr 2
A
(A) GA16 PEDESTAL for 6", 7", 8" and 10" grinders, carbide and diamond wheel grinders, 1/4 Hp through 1-1/2 Hp buffers and belt grinders. Height 32 7/8". GA16RE for 6" & 7" grinders "all steel construction". Height 34".(B) GA14 PEDESTAL – Fabricated steel, for 6", 7", 8" and 10" grinders, 1/4 Hp through 1-1/2 Hp buffers. Height 34-1/2".(C) GA20 PEDESTAL for 8", 10", 12" and 14" grinders and 3/4 through 7-1/2 Hp buffers. Height 30". GA20RE for 8" & 10" grinders "all steel construction". Height 34".(D) GA24 WATER POT for 623E, 632E, 673E, 612E, 662E, and 7" (except #712, #712R, #762, & #762R), 8" and 10" grinders. Supplied with mounting bracket and swivel arm. Capacity 1-1/2 pints.(E) GA3 WATER POT for GA20 pedestal. Capacity 3 pints.(F) GA25 TOOL TRAY for 623E, 632E, 673E, 612E, 662E and all 7" (except #712, #712R, #762, & #762R), 8" and 10" grinders. Supplied with mounting bracket and swivel arm. Diameter 8". Area 48 square inches.(G) GA4 TOOL TRAY for GA20 pedestal. Dimensions 12" x 6".(H) GA11 EYESHIELD – 6" x 4" Shatter resistant Plexiglas®. Fits Baldor grinders 7” through 14”.(I) GA10 EYESHIELD – 5" x 4" Shatter resistant Plexiglas®. Fits Baldor 6" grinders and #712, #712R, #762 and #762R.(J) GA9 LIGHTED EYESHIELD – 5 1/2" x 3 3/4" viewing area made of Shatter resistant Plexiglas®. Accommodates standard 115 volt 60-watt bulb. Easy to attach to all Baldor grinders except Baldor carbide tool grinders and belt grinders; Less on/off switch. U.L. Component Recognized / CSA Certified. Adjusts horizontally or vertically. * Supplied less bulbs.(J-1) GA9-1 – Same as GA9 except packed 1 per carton. 115 Volts, only.(K) GA9S LIGHTED EYESHIELD WITH ON/OFF SWITCH. 115 Volts only.(L) GA13 EYESHIELD – Replacement for 600E, 600RE, 602E and 602RE Grinders
NOTE: J, J1, & K lighted eyeshields supplied less bulbs. Rough service bulbs are suggested.
B C
J
F G
I K
D E
Grinder - Buffer Accessories
L
A B
H
16
CatalogNumber
ListPrice Each
Diameter Face * BoreShippingWeight
A65 9 6" 1/4" 1/2" 1
A82 15 8" 1/4" 3/4" 1
A103 19 10" 1/4" 7/8" 1
WHEELS FOR GRINDERSWheels are aluminum oxide, medium grade, vitrified bond.
SEWED COTTON BUFFING WHEELSWheels are muslin cloth, spiral sewn.
CatalogNumber
ListPrice Each
Diameter Face Bore GritShippingWeight
B66 17 6" 3/4" 1/2" 36 2
B67 17 6" 3/4" 1/2" 60 2
B73 24 7" 1" 5/8" 36 4
B74 24 7" 1" 5/8" 60 4
B80 30 8" 1" 3/4" 36 5
B81 30 8" 1" 3/4" 60 5
B102 45 10" 1" 7/8" 36 8
B103 45 10" 1" 7/8" 60 8
B125 106 12" 2" 1 1/4" 30 22
B126 106 12" 2" 1 1/4" 46 22
B147 200 14" 3" 1 1/4" 30 42
B148 200 14" 3" 1 1/4" 46 41
NOTES: Cotton wheels are supplied in sections 1/4" wide. Two (or more) sections may be put together to make up wheel of desired width. * These bore sizes will fit shafts 1/8” greater diameter than bore.
Accessories
6” 8” 10”
6” 7” 8” 10” 12” 14”
17
ItemNumber
CatalogNumber
DescriptionList
PriceShippingWeight
M AB248 Abrasive Belt 2" x 48" – 80 Grit 13 1
CatalogNumber
ListPrice Each
Diameter Face BoreDiameterOf Wire
ShippingWeight
W64 21 6" 5/8" 1/2" .014 1
W70 25 7" 5/8" 5/8" .014 1
W82 29 8" 3/4" 3/4" .014 1
WIRE BRUSH WHEELSWheels are crimped, carbon steel wire.
NOTES: When installing new wheels, check wheel for possible damage. Do not use a damaged wheel. Wear safety glasses. With new wheel installed and all safety guards in place and operator standing away from front of grinder, run grinder
for one minute before applying work. Exercise caution.
6” 7” 8”
ABRASIVE BELT
Accessories
M
18
MOD EXPRESS TM
Grinder Buffer Manual Magnetic
WheelSize
Hp115/230 Volts 115 Volts 230 Volts
Catalog Number
ListPrice
CatalogNumber
ListPrice
CatalogNumber
ListPrice
6" 1/3 GA27A-6 296 GA41A-6 545 N/A N/A
7" N/A GA27A-7 296 GA41A-7 545 GA44A-7 545
8" 3/4 GA27A-8 296 GA41A-8 618 GA44A-8 545
10" 1 GA27A-10 296 GA41A-10 597 GA44A-10 545
N/A 1 1/2 GA27A-10 296 GA42A 597 GA45A 545
12" 2 S/E S/E GA43A * 722 GA46A * 628
Grinder Buffer Manual Magnetic
WheelSize
Hp208-230/460 Volts 208-230 Volts 460 Volts**
Catalog Number
ListPrice
CatalogNumber
ListPrice
CatalogNumber
ListPrice
7” N/A GA47A-7 344 GA50A-7 545 GA53A-7 545
8” 3/4 GA47A-8 344 GA50A-8 545 GA53A-8 545
10” 11/2 GA47A-10 344 GA50A-10 545 GA53A-10 545
12” 2 S/E S/E GA51A * 382 GA54A * 382
12” 3 S/E S/E GA52A * 382 GA55A * 382
MANUAL AND MAGNETIC STARTERSMounted and wired on Baldor Industrial Grinders and Buffers. Starters are in NEMA 1 Enclosure and have the push button in cover. Available only as factory installed options. Ask about controls for 575 volt Grinders. Controls not available for Belt Grinders and Tool Grinders.
STARTER – SINGLE PHASEFULL VOLTAGE CONTROLSpecify Voltage When Ordering
Manual Starter
STARTER – THREE PHASEFULL VOLTAGE CONTROLSpecify Voltage When Ordering
NOTES: N/A = Not Available S/E = Standard Equipment These starters provide overload protection. *Price includes allowance for omission of standard starter. **Starters for 575 volts are available for the same prices
Magnetic Starter
Stock Products Modification Program
19
MOD EXPRESS TM
Dust Control Unit
Magnetic Relay
ListPrice
DC7, DC8, DC10, DC12 GA91A 364
DC7-3, DC8-3 GA92A 364
DC10-3, DC12-3, DC14-3 GA92A 364
OVERLOAD PROTECTION FOR DUST CONTROL UNIT(Must be used with Magnetic Control)
NOTES: The price of the control includes wiring and mounting of control on a combination grinder-dust control mounted on a pedestal.
Example: 8107W $581.00, GA41A-8 $403.00, GA16 $203.00, DC8 $613.00, GA91A $345.00. The unit is shipped completely wired and assembled, ready to install on location.
MOD EXPRESS TM
MANUAL AND MAGNETIC STARTERSMounted and wired on Baldor Industrial Grinders and Buffers. Starters are in NEMA 1 Enclosure and have the push button in cover. Available only as factory installed options. Ask about controls for 575 volt Grinders. Controls not available for Belt Grinders and Tool Grinders.
Stock Products Modification Program
MAGNETIC STARTER – THREE PHASEWITH LOW VOLTAGE CONTROL
Specify Voltage When Ordering
Magnetic Starter with Low Voltage Control
Grinder BufferMagnetic with 110 Volt Control
Circuit Transformer
208-230 Volts 460 Volts**
WheelSize
HpCatalogNumber
ListPrice
CatalogNumber
ListPrice
7" N/A GA56A-7 † 1226 GA60A-7 † 1357
8" 3/4 GA56A-8 † 1226 GA60A-8 † 1357
10" 1 1/2 GA56A-10 † 1226 GA60A-10 † 1357
12" 2 GA57A-12-2 *† 1202 GA61A-12-2 *† 1229
12" 3 GA57A-12-3 *† 1202 GA61A-12-3 *† 1229
14" 5 GA58A-14-5 *† 1202 GA61A-14-5 *† 1229
14" 7 1/2 GA58A-14-7 *† 1202 GA62A-14-7 *† 1229
NOTES: J.I.C. (Electrical Standards) controls available for some models – contact factory with complete description of control required for price and availability. * Price includes allowance for omission of standard starter. ** Starters for 575 volts available for the same prices. † GA9 eyeshields may be wired through magnetic starter – 100 watt extra capacity transformer is required. Add $147.00 to starter list price and designate letter “T” to starter catalog number (Example: GA56A-8T – $800.00) N/A = Not Available Starters provide overload protection.
20
General InformationThis catalog shows the most commonly requested replacement parts for Baldor grinders, buffers, dust control units and accessories. Many other replacement parts are available. For information on parts not shown, contact your Baldor District Office.
Ordering InformationFor replacement parts not shown, please provide complete description and complete nameplate data, especially noting the Baldor Specification Number (Spec. No.).
WARRANTY FORBALDOR GRINDER / BUFFER PRODUCTS
Baldor Gr inder / Buffer products, inc luding dust contro l uni ts, are warranted for 3 fu l l years against burnouts, defect ive mater ia l and workmanship. Warranty covers al l parts except those subject to normal wear such as wheels. The ser ia l number indicates the month and year of manufacture — this determines the warranty period.
MANUFACTURED IN U.S.A.BY BALDOR ELECTRIC CO.
CAT. NO.
H.P.
PHASE
HZ.
FRAME
SPEC. NO.
VOLTS
AMPS
R.P.M.
SERIAL NO.
TYPICAL NAMEPLATE
Instruction sheets for Baldor Grinder/Buffer Products are available See listing on parts page
Touch-up Paint – 12 oz. aerosol can
Battleship Gray – #MG1000G23SP $15.00 per can
Cardinal Red – #MG1000R22SP $15.00 per can
21
Baldor 6" & 7" Grinders 1/4 Hp & 1/3 Hp Buffers
Item#
Part DescriptionPart Number
6" List
PricePart Number
7" List
Price1 Rubber Feet (6" made thru 2002) RM1005A01SP 3 RM1005A01SP 3
* 2 Tool Rest Support, Pressed Steel HA6048A01SP 8 HA6048A01SP 8* 2A Tool Rest Support, Cast Iron HA6064A01SP 16 HA6064A01SP 16* 3 Guard, Non-Exhaust Type (Right Hand or Left Hand) G6FH3800SP 16 G7FH3800SP 30* 3A Guard, Exhaust Type (Right Hand) Cast Iron G6FH1802A01 46 G7FH1802A01SP 75* 3B Guard, Exhaust Type (Left Hand) Cast Iron G6FH1800A01(SP) 46 G7FH1800A01SP 75* 4 Guard Cover, Non-Exhaust Type (Right Hand or Left Hand) G6FH3801SP 24 G7FH3801SP 37* 4A Guard Cover, Exhaust Type (Right Hand) Cast Iron G6FH1803A01SP 36 G7FH1803A01SP 44* 4B Guard Cover, Exhaust Type (Left Hand) Cast Iron G6FH1801A01SP 36 G7FH1801A01SP 44* 5 Tool Rest, Pressed Steel (Right Hand or Left Hand) G6AP1009A01SP 10 G7AP1010A01SP 11* 5A Tool Rest, Cast Iron, (Right Hand or Left Hand) G6AP1008A01SP 29 G6AP1008A01SP 29
6 Arbor Nut (Left Hand) XY5020A62SP (1/2-20) 5 XY6311A62SP (5/8-11) 5* 7 Grinding Wheel See Page No. 6 - See Page No. 6 -* 8 Spark Arrestor, Solid Type (use with non-exhaust wheel guards) G6AP1003A01SP 6 G6AP1003A01SP 6* 8A Spark Arrestor, Slotted Type (use with exhaust wheel guards) G6AP1002A01SP 11 G6AP1002A01SP 11
9 Felt Washer HA1025A01SP 11 HA1025A02 (C) 1110 Wound Stator Assembly Specify Spec. No. (C) 185 Specify Spec. No. (C) 29711 Thru Bolt HA3100A07 (C) 2 HA3100A11 (C) 512 Rotor, with Shaft & Bearings Specify Spec. No. 163 Specify Spec. No. 20313 Endplate (Right Hand or Left Hand) G6EP3900A01 (C) 29 G7EP3900A01 (C) 3614 Bearing BG6203E03SP 25 BG6203C03 (C) 25
* 15 Grinding Wheel See Page No. 8 - See Page No. 8 -16 Wheel Flange, Inside or Outside, Pressed Steel HA6113SP 7 HA6115A01SP 7
16A Wheel Flange, Inside or Outside, Cast HA6050A02SP 10 HA6096A01SP 1117 Arbor Nut (Right Hand) XY5020A12SP (1/2-20) 4 XY6311A12 SP (5/8-11) 5
* 18 Tool Rest, Pressed Steel (Right Hand or Left Hand) G6AP1009A01SP 10 G7AP1010A01SP 11* 18A Tool Rest, Cast Iron (Right Hand or Left Hand) G6AP1008A01SP 29 G6AP1008A01SP 29
19 Cord and Plug LD5001A07 (C) 24 LD5001A07 (C) 2420 Base G6BA3000SP 33 G7BA3000 (C) 5321 Base Cover G6CB4500A01 (C) 9 G7CB4500 (C) 1122 Switch On - Off (Single Phase) SP9017SP 13 SP9000 SP 24
22A Switch On - Off (Three Phase) None - SP9004 (C) 2823 Relay RE1020SP 22 None -N/S Capacitor Specify Spec. No. - Specify Spec. No. -
** N/S Vinyl Cap RM1010A04 2 None -N/S Spacers for Wire Brush Wheels (3 Req’d) HW1000A50 (C) 2 (2 Req’d.) HA2047A01 (C) 5N/S Spacer, Flange (for non-exhaust type) None - HA2072 (C) 8N/S Spacer, Flange (for exhaust type) None - HA2040A01SP 8
Instruction Sheet for 6" thru 14" Grinders — MN903 – #275P is available at no charge.Instruction Sheet for Buffers — MN906 – #280F is available at no charge.Instruction Sheet for Grinder-Buffers — MN907 – #285B is available at no charge.
i
{
QW
E
R
T
Y
U
IO
P } qw
e
r
t
y
uop[
NOTES: * Grinders only. ** Buffers only. N/S – Not shown on diagram.
22
Baldor 8" thru 14" Grinders 3/4 Hp thru 10 Hp Buffers
NOTES: ➀ Guards for 812RE and 862RE. Guard (Right Hand) G8FH1800A02, Guard (Left Hand) G8FH1802A02. ➁ Cat. #812RE and #862RE are painted red. For red 8" grinder parts, order as “custom” part. Note: “Painted Red” Tool Rests and Supports for Cat. #812RE and 862RE are the same as 7" pressed steel on page 21. Instruction Sheet for 6" thru 14" grinders — MN903 – #275P is available at no charge. Instruction Sheet for Buffers — MN906 – #280F is available at no charge. Instruction Sheet for Grinder-Buffers — MN907 – #285B is available at no charge. N/S = Not shown on diagram. * Grinders only. ** Buffers only.
Item #
Part DescriptionPart Number
8"List
PricePart Number
10" List
Price Part Number
12"List
Price Part Number
14”List
Price*1 Guard (Right Hand) G8FH1800A01SP 130 G0FH1806A01 182 G2FH1804A01 324 G4FH1800A01 484*2 Guard (Left Hand) G8FH1802A01SP 130 G0FH1807A01SP 182 G2FH1805A01 324 G4FH1801A01 468*3 Guard Cover (Right Hand) G8FH1801A01SP 65 G0FH1805A01SP 101 G2FH1806A01 140 G4FH1802A01 164*4 Guard Cover (Left Hand) G8FH1803A01SP 65 G0FH1804A01 101 G2FH1807A01 136 G4FH1803A01 159
*5Tool Rest
(Right Hand or Left Hand)G8AP1003A01SP 30 G8AP1003A01SP 30 G2AP1002A01SP 42 G2AP1002A01SP 42
*6Tool Rest Support
(Right Hand or Left Hand)HA6099A01SP 22 HA6101A01SP 23 HA6049A01SP 32 HA6049A01SP 32
7 Arbor Nut (Left Hand) XY7510A62SP 7 XY8809A62SP 9 XZ2007A62SP 22 XZ2007A62SP 22*8 Spark Arrestor G6AP1002A01SP 11 G0AP1002SP 15 G2AP1001 20 G2AP1001 20 9 Wound Stator Assembly Specify Spec. No. 383 Specify Spec. No. 468 Specify Spec. No. 824 Specify Spec. No. 1056
10Rotor with Shaft & Bearings,
(Less Nuts & Flanges)Specify Spec. No. 289 Specify Spec. No. 352 Specify Spec. No. 563 Specify Spec. No. 629
11Endplate
(Right Hand or Left Hand)G8EP3900A01SP 58 G8EP3900A01SP 58 G2EP1900A01 138 G4EP1900A01 203
12 Bearing BG6206E03 41 BG6206E03 41 BG6208E03 31 BG6309E03 5013 Wheel Flange, Inside or Outside HA6098 11 HA6100SP 20 HA6051SP 26 HA6051SP 2614 Arbor Nut (Right Hand) XY7510A12SP 4 XY8809A12SP 6 XZ2007A12SP 21 XZ2007A12 2115 Base G8BA3000A01 79 G8BA3000A01 79 G2BA1000A01 178 G4BA1000A01 18916 Switch On - Off (Single Phase) SP9000SP 24 SP9000SP 24 None - None -
16A Switch On - Off (Three Phase) SP9004 28 SP9004 28 None - None -N/S Base Cover G8CB4500A02 7 G8CB4500A02 7 G2CB4500 18 None -N/S Cord & Plug (Single Phase) LD5001A02 24 None - None - None -
N/SCapacitor, Electrolytic
(Single Phase)None - None - ECI645A06SP 30 None -
N/S Starter Bracket None - None - Specify Spec. No. - Specify Spec. No. -N/S Starting Relay (Single Phase) None - None - RE5019 135 None -
N/SCapacitor (Oil Type)
(Single Phase)Specify Spec. No. - Specify Spec. No. - None - None -
17 Thru Bolts HA3100A14 5 HA3100A14 5 HA3104A13 5 HA3104A14 5N/S Rubber Feet RM1005A01SP 3 RM1005A01SP 3 None - None -
**N/S Bearing Retainer RB3010 13 RB3010 13 RB1029A01 30 RB1028A01 32**N/S Vinyl Cap to Cover Arbor Nut RM1010A06 2 RM1010A05SP 3 RM1010A07 5 RM1010A07 5**N/S Spacer HA2048A01SP 7 HA2050A01 8 None - None -*18 Grinding Wheel See Page 16
WR
{ O{
IQE
YT
w
}
P
q
er
}
q
r
I
y
23
e
u
}
q p
t
O{P
Y
U
TR
}
i
U
o
IEQW
r
w
I{P
yO
Item#
Part Description Part NumberList
PriceShippingWeight
1 Rotor, with Shaft and Bearings Specify Spec. No. 334 18.0
A 2 Ball Bearing BG6204E03 28 1.5
B 3 Ball Bearing BG5204C03 58 1.5
4 Endplate (Right Hand for Carbide Grinders) G9EP1900A03 76 5.0
4A Endplate (Right Hand for Diamond Wheel Grinders) G9EP1900A10 76 5.0
5 Endplate, Left Hand G9EP1900A02 76 5.0
6 Wound Stator Assembly Specify Spec. No. 441 21.0
7 Guard, Wheel (Right Hand or Left Hand) G9FH1800A01 77 9.0
8 Flange, Wheel (Right Hand or Left Hand) HA6104A01SP 35 1.0
9 Tool Table, less Rocker (Right Hand or Left Hand) G9AP1000A01 121 7.5
10 Rocker for Table G9AP1003A01SP 19 1.0
11 Clamp with Handle HA5001A01SP 16 1.0
12 Water Pot and Water Cock G9AP5001A01 51 3.0
13 Water Tray G9AP1001A01 43 9.5
14 Base G8BA3000A02 79 4.0
15 Machine Tool Light G9AP1006A01SP 70 2.5
16 Switch (115 Volt - Single Phase) SP9019SP 28 1.0
16A Switch (Three Phase) SP9035SP 50 1.0
17 Tool Rest (Protractor Type) G9AP5000A01SP 64 1.0
18 Screws for Tool Table HA3407A01 3 1.0
19 Shade Only (For light) G9AP1006SP 20 1.0
20 Screw for Mounting Wheel HA3007A01SP 6 1.0
21 Screw for Mounting Diamond Wheels 91XN2520A12 2 1.0
22 Cord and Plug LD5001A02 24 1.0
N/S Arbor Nut (3/4 x 16 Jam Nut)(Right hand or Left hand) HA3203A12 6 1.0
N/S Base Cover G8CB4500A02 7 1.0
N/S Capacitor 12 mfd. OC3012F12SP 25 1.0
N/S Pointer (angle) (Right Hand) G9AP1005A01 4 1.0
N/S Pointer (angle) (Left Hand) G9AP1005A02 4 1.0
N/S Slinger for Shaft HA1005A03SP 4 1.0
N/S Thru Bolts HA3100A45 6 1.0
N/S Vinyl Cap (Arbor Nut Cover) RM1010A06 2 1.0
N/S Instruction Sheet MN905 – 281H N/C -NOTES: N/S = Not shown on diagram A Bearing for left and right side of Carbide Grinders and left side of Diamond Wheel Grinders B Bearing for right side of Diamond Wheel Grinders only.
Baldor Carbide &Diamond Wheel Grinders
24
Baldor Abrasive Belt Grinders
EXHAUST
ROTATION
13
21➉
20
19
18
22
24
➂
➁
36
➃
37
25
17
12
15
SIDE VIEW
15
17
TOP VIEW
13
19
➃
➈11
➉
41
14
16
17
27
➇➀➆
31
38
42
31
40
18
2930
28
➅32
34
➁ 33
➂
26
24
39
22
18
23
21
➄
25
Baldor Abrasive Belt Grinders
NOTES: * Belt Guard Kit – to replace plastic guard on #2048-151D and 153D manufactured before 1985. See parts on page 24. N/S = Not shown on diagram. Instruction Sheet for Belt Grinders MN902 – #279J is available at no charge.
Item#
Part DescriptionPart
NumberList
PriceShippingWeight
1 ✓ Motor — #2048-151D (Spec. No. B2-3A) 35H713W811 764 47
1A ✓ Motor — #2048-153D (Spec. No. B2-3C) 35H714-82 730 39
1B ✓ Motor — #248-151TD (Spec. No. B2-5A) 35G400W811 764 47
1C ✓ Motor — #248-153TD (Spec. No. B2-5C) 35H410-82 730 39
1D ✓ Motor — #248-181TD (Spec. No. B2-6D) G8-0378-0350 804 56
1E ✓ Motor — #248-183TD (Spec. No. B2-6C) G8-319-318 804 52
1F ✓ Motor — #248-151AS (Spec. No. B2-8A) 35P486Z331 1058 54
1G ✓ Motor — #248-251AS (Spec. No. B2-8C) 35P486Z332 1058 44
2 ✓ ✓ Base G8BA3000A01 79 4
2A ✓ ✓ Base G8BA3000A07 79 4
2B ✓ ✓ Base G8BA3000A10 79 4
3 ✓ ✓ ✓ ✓ ✓ On - Off Switch (Single Phase) SP9002SP 41 1
3A ✓ ✓ ✓ On - Off Switch (Three Phase) SP9004 28 1
4 ✓ ✓ ✓ ✓ ✓ ✓ ✓ Base Cover G8CB4500A02 7 1
4A ✓ Base Cover G8CB4500A05 14 1
5 ✓ ✓ ✓ ✓ ✓ ✓ Fan Cover 35FH4005A01SP 22 1.5
6 ✓ ✓ ✓ ✓ ✓ ✓ Fan – External 35FN3002A05SP 21 1
7 ✓ ✓ ✓ ✓ Endplate (Left Hand for Motor) 35EP3100A02SP 65 1.5
7A ✓ ✓ Endplate (Left Hand for Motor) G8EP3900A01SP 58 2
7B ✓ ✓ Endplate (Left Hand for Motor) 35EP3106A16 74 1.5
8 ✓ ✓ ✓ Endplate (Right Hand for Motor) 35EP3300A33 74 2
8A ✓ ✓ Endplate (Right Hand for Motor) 35EP3300A44 74 2
8B ✓ Endplate (Right Hand for Motor) 35EP3300A02SP 75 2
8C ✓ ✓ Endplate (Right Hand for Motor) 35EP1318A04 95 2
9 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Guard for Idler Wheel B2FH2801A01SP 108 3.5
10 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Guard Cover for Idler Wheel B2FH2808A01SP 43 1
11 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Idler Wheel with Bearings B2AP3003A01SP 132 2.5
12 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Tension Spring for Idler Wheel HA7001A01SP 20 1
13 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Idler Arm – Less Wheel HA5004A01SP 85 2
14 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Tracking Arm HA6134A01SP 37 1.5
15 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Latch Stop – for Idler Arm B2AP1000A01 24 1
16 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Adjusting Knob – for Tracking HA5000A01 14 1
#20
48-1
51D
SPE
C. #B2
- 3A
#204
8-15
3D
SPEC
. #B2
- 3C
#
248-
151T
D S
PEC. #
B2 -
5A
#2
48-1
53TD
SP
EC. #
B2 -
5C
#24
8-18
1TD
SPE
C. #B2
- 6D
#24
8-18
3TD
SPE
C. #B2
- 6C
#248
-151
AS
SPEC
. #B2
- 8A
#
248-
251A
S S
PEC. #
B2 -
8B
EXHAUST
ROTATION
26
NOTES: * Belt Guard Kit – to replace plastic guard on #2048-151D and 153D manufactured before 1985. See parts on page 24. N/S = Not shown on diagram. Instruction Sheet for Belt Grinders MN902 – #279J is available at no charge.
Item#
Part DescriptionPart
NumberList
PriceShippingWeight
17 ✓ ✓ ✓ ✓ ✓ ✓ Bracket – Idler Pivot Arm HA6218A01 181 5
17A ✓ ✓ Bracket – Idler Stationary Arm HA6218A02 174 5
18 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Tool Rest G8AP1003A01SP 30 1.5
19 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Support for Tool Rest and Platen HA6068A02 162 2
20 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Platen only B2AP1005A02 24 1.5
21 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Abrasive Belt 2" x 48" – 80 Grit AB248 14 1
22 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Contact Wheel – 7" x 2" B2AP5001A01SP 264 2.5
23 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Guard – for Contact Wheel B2FH2806A01SP 57 1
24 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Guard Cover (Inside) for Contact Wheel B2FH2811A01 74 3
24A ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Guard Cover (Outside) for Contact Wheel B2FH2810A01 113 3
25 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Belt Guard – Rear Portion B2FH2809A01SP 43 2
26 ✓ ✓ ✓ ✓ ✓ ✓ Pull Knob – for Pivot Arm HW2404A01 3 1.5
27 ✓ ✓ ✓ ✓ ✓ ✓ Adapter for Pivot Arm HA6219A01 38 5
28 ✓ ✓ Wheel Guard (Left Hand) G8FH1802A01SP 130 10
29 ✓ ✓ Guard Cover (Left Hand) G8FH1803A01SP 65 7
30 ✓ ✓ Tool Rest Support HA6099A01SP 22 1
31 ✓ ✓ Wheel Flange (Inside and Outside) HA6098 11 2
32 ✓ ✓ Speed Control Knob Kit BC149 9 1
33 ✓ Plug-In Resistor (Speed Control) WD3007A12 3 1
33A ✓ Plug-In Resistor (Speed Control) WD3007A10 3 1
34 ✓ ✓ Potentiometer Kit (Speed Control) BC148 8 1
36 ✓ Electronic Speed Control Board CN3000A18SP 154 1
36A ✓ Electronic Speed Control Board CN3000A01SP 171 2
37 ✓ ✓ Cord with Plug (115 Volt) LD5014 36 1
38 ✓ ✓ Spark Arrestor G6AP1002A01SP 11 1
39 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Arbor Nut (Right Hand) XY7510A12SP 4 1
40 ✓ ✓ Arbor Nut (Left Hand) XY7510A62 7 1
41 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Pivot Shaft – for Tracking Arm HA3504A01 15 1
42 ✓ ✓ Grinding Wheel – 8" x 1" x 3/4" – 36 Grit B80 31 5
N/S ✓ Brush (Replacement Carbon Brush) BP5000P07SP 33 1
N/S ✓ Brush (Replacement Carbon Brush) BP5000T15SP 35 1
N/S *Belt Guard Kit A641 332 18
#20
48-1
51D
SPE
C. #B2
- 3A
#204
8-15
3D
SPEC
. #B2
- 3C
#
248-
151T
D S
PEC. #
B2 -
5A
#2
48-1
53TD
SP
EC. #
B2 -
5C
#24
8-18
1TD
SPE
C. #B2
- 6D
#24
8-18
3TD
SPE
C. #B2
- 6C
#248
-151
AS
SPEC
. #B2
- 8A
#
248-
251A
S S
PEC. #
B2 -
8B
EXHAUST
ROTATION
Baldor Abrasive Belt Grinders
27
Baldor Dust ControlAccessories
NOTES: * Sold in sets only – Set includes one each of Item #6, 8 and 14. † Sold in sets only – Set includes one each of Item #6A, 8A and 14A. Instruction Sheet for Baldor “Dust Control Unit” – MN902 – #282C available at no charge.
Item#
NOTE: Suffix letter (A - B) is similar to number shown above.
Part Description Part Number List Price
1 ✓ ✓ ✓ ✓ Dust Bag (Treated with flame retardant) ARB-1 44
1A ✓ Dust Bag (Treated with flame retardant) ARB-2 61
2 ✓ ✓ ✓ ✓ Bag Clamp and Hose Clamp 4" dia. 31379CF 7
2A ✓ Bag Clamp (6" dia.) 31244CF 7
3 ✓ ✓ ✓ ✓ Bag Elbow (4" dia.) 51269 33
4 ✓ ✓ ✓ ✓ Cord set with switch (for 115 Volt only) LD5022A01 58
5 ✓ ✓ ✓ ✓ Motor – Baldor #VM3537 (3 Phase) 1/2 HP VM3537 237
5A ✓ ✓ ✓ ✓ Motor – Baldor #VL3503 (1 Phase) 1/2 HP VL3503 223
5B ✓ Motor – Baldor #VM3545 (3 Phase) 1 HP VM3545 294
6 ✓ ✓ ✓ ✓ Housing, CW, M.S., SPB-9 34025 281
7 ✓ ✓ ✓ ✓ Blower Wheel #1058 5530602 184
7A ✓ Blower Wheel 11" x 3" BC, CW 55098-02 229
9 ✓ ✓ ✓ ✓ Mounting Plate 03253 215
9A ✓ Mounting Plate 03255 219
10 ✓ ✓ Inlet Box with 3" Ports 51229 103
10A ✓ Inlet Box with 5" Ports (for DC14-3) 51081 97
10B ✓ Inlet Box with 4" Ports 51230 103
10C ✓ Inlet Box with 5" Ports (for DC12) 51231 103
11 ✓ ✓ Hose Clamp (3" dia.) 31013SP 7
11A ✓ ✓ Hose Clamp (5" dia.) 31016 7
12 ✓ ✓ Hose (3" dia. x 14") 31100 31
12A ✓ Hose (4" dia. x 14") 31101 36
12B ✓ ✓ Hose (5" dia. x 18") 31496 41
13 ✓ ✓ ✓ ✓ Discharge Guard, Ribbed Type (4”) 29330 21
14 ✓ Inlet Collar (7") 26143 †
DC
7
DC
8
DC
10
DC
12
DC
14-3
P
w
{}
O
IU
Y
T
R
E
W
Q
q
28 28
Baldor Eyeshields
Item
#Part Description
GA10 (G6-220) GA11 (A-516)1 GA9 (G7-236) and
GA9S (G7-281)
Part Number Price Part Number Price Part Number Price
1 Plexi-glass Pane 2 G6AP5001A01A 17 2 G7AP5003A01SP 17 G7AP1007A01SP 14
2 Mounting Arm HA6093A01 SP 11 HA6103A01 11 HA6103A01SP 11
3 Mounting Arm Clamp HA6094A01 SP 7 HA6094A01 11 HA6094A01SP 11
4 Frame - - - - G7AP1006 31
5 Cord with Plug - - - - LD5001A02 24
6 Lamp Socket - - - - WD4003A01 8
7On - Off Switch(GA9S and GA9SR only)
- - - - SP9026 13
8Swivel Bracket(Bulb Socket Retainer Plate)
- - - - HA6102A01SP 13
9 Cord Strain Relief - - - - WD4102A01 3
NOTES: 1 Parts for GA9 and GA9S also apply to GA9R and GA9SR. No bulbs are supplied. Rough service bulbs are suggested, maximum 60 watts. 2 Plexi-glass pane on GA10 and GA11 include mounting bracket. Instruction sheet MN909 – #283A is available at no charge.
QW
E
Q
W
E
TO
UY
R
I
Q
29
Baldor Pedestals
Item
#Part Description
GA16 GA20
Part Number Price Part Number Price
1 Base (Cast Iron) G6BA1001A01 176 G8BA1002A01 3652 Column Assembly G8BA5000A03 135 G8BA5000A01 2573 Top Plate (Cast Iron) HA6069A01 70 G8BA1001A01 90
WARNING
GA16 PEDESTAL
WARNING
GA20 PEDESTAL
TOP PLATE (CAST IRON)E
COLUMN ASSEMBLY
W
BASE (CAST IRON)
Q
P.O. Box 2400 • Fort Smith, AR 72902-2400 U.S.A.Ph: (479) 646-4711 • Fax (479) 648-5792
International Fax (479) 648-5895www.baldor.com
© Baldor Electric Company11G
Printed in U.S.A.12/04 PROG 10000
GERMANY DIESELSTRASSE 22 D-85551 KIRCHHEIM MUNICH, GERMANY PHONE: (49) (89) 90508 - 0 FAX: (49) (89) 90508 - 491
ITALY BALDOR ASR AG MENDRISIO OFFICE VIA BORROMINI, 20A 6850 MENDRISIO SWITZERLAND PHONE: 0041 91 640 99 50 FAX: 0041 91 630 26 33
JAPAN DIABLDG 802, 2-21-1 TSURUYA-CHO, KANAGAWA-KU YOKOHAMA, 221-0835, JAPAN PHONE: 81-45-412-4506 FAX: 81-45-412-4507
KOREA ROOM 210 BUPYEONG INDUSTRIAL COMMERCIAL COOP. 396-13 CHEONGCHEON 2-DONG, BUPYEONG-GU INCHEON, KOREA, 403-858 PHONE: 82-32-508-3252 FAX: 82-32-508-3253
MÉXICO BLVD. AL AEROPUERTO, KM. 2 LEÓN 37545, GUANAJUATO, MÉXICO PHONE: 52-477-761-2030 FAX: 52-477-761-2010
SINGAPORE 51 KAKI BUKIT ROAD 2 K B WAREHOUSE COMPLEX SINGAPORE 417863 PHONE: (65) 6 744 2572 FAX: (65) 6 747 1708
SWITZERLAND POSTFACH 73 SCHUTZENSTRASSE 59 CH-8245 FEUERTHALEN SWITZERLAND PHONE: (41) (52) 6474700 FAX: (41) (52) 6592394
TAIWAN ROOM R, 2F, NO. 124 CHUNG CHENG ROAD, SHIHLIN DIST. TAIPEI 11141 PHONE: (886-2) 8866-2991 EXT. 802 FAX: (886-2) 2838-2816
UNITED KINGDOM 6 BRISTOL DISTRIBUTION PARK HAWKLEY DRIVE BRISTOL BS32 0BF U.K. PHONE: 44 1454 850000 FAX: 44 1454 859001
MISSOURI (cont.) KANSAS CITY 915 N W PLATTE VALLEY DR RIVERSIDE, MO 64150 PHONE: 816-587-0272 FAX: 816-587-3735
NEW YORK AUBURN ONE ELLIS DRIVE AUBURN, NY 13021 PHONE: 315-255-3403 FAX: 315-253-9923
NORTH CAROLINA GREENSBORO 1220 ROTHERWOOD ROAD GREENSBORO, NC 27406 P O BOX 16500 GREENSBORO, NC 27416 PHONE: 336-272-6104 FAX: 336-273-6628
OHIO CINCINNATI 2929 CRESCENTVILLE ROAD WEST CHESTER, OH 45069 PHONE: 513-771-2600 FAX: 513-772-2219
CLEVELAND 8929 FREEWAY DRIVE MACEDONIA, OH 44056 PHONE: 330-468-4777 FAX: 330-468-4778
OKLAHOMA TULSA 2 EAST DAWES BIXBY, OK 74008 PHONE: 918-366-9320 FAX: 918-366-9338
OREGON PORTLAND 20393 SW AVERY COURT TUALATIN, OR 97062 PHONE: 503-691-9010 FAX: 503-691-9012
INDIANA INDIANAPOLIS 5525 W. MINNESOTA STREET INDIANAPOLIS, IN 46241 PHONE: 317-246-5100 FAX: 317-246-5110 800-428-4141
IOWA DES MOINES 1800 DIXON STREET, SUITE C DES MOINES, IA 50316 PHONE: 515-263-6929 FAX: 515-263-6515
MARYLAND BALTIMORE 6660 SANTA BARBARA RD. SUITE 22-24 ELKRIDGE, MD. 21075 PHONE: 410-579-2135 FAX: 410-579-2677
MASSACHUSETTS BOSTON 6 PULLMAN STREET WORCESTER, MA 01606 PHONE: 508-854-0708 FAX: 508-854-0291
MICHIGAN DETROIT 33782 STERLING PONDS BLVD. STERLING HEIGHTS, MI 48312 PHONE: 586-978-9800 FAX: 586-978-9969
GRAND RAPIDS 668 3 MILE ROAD NW GRAND RAPIDS, MI 49504 PHONE: 616-785-1784 FAX: 616-785-1788
MINNESOTA MINNEAPOLIS 21080 134TH AVE. NORTH ROGERS, MN 55374 PHONE: 763-428-3633 FAX: 763-428-4551
MISSOURI ST LOUIS 422 INDUSTRIAL DRIVE MARYLAND HEIGHTS, MO 63043 PHONE: 314-298-1800 FAX: 314-298-7660
PENNSYLVANIA PHILADELPHIA 1035 THOMAS BUSCH MEMORIAL HIGHWAY PENNSAUKEN, NJ 08110 PHONE: 856-661-1442 FAX: 856-663-6363
PITTSBURGH 616H BEATTY ROAD MONROEVILLE, PA 15146 PHONE: 412-380-7244 FAX: 412-380-7250
TENNESSEE MEMPHIS 4000 WINCHESTER ROAD MEMPHIS, TN 38118 PHONE: 901-365-2020 FAX: 901-365-3914
TEXAS HOUSTON 4647 PINE TIMBERS SUITE # 135 HOUSTON, TX 77041 PHONE: 713-895-7062 FAX: 713-690-4540
DALLAS 3040 QUEBEC DALLAS, TX 75247 PHONE: 214-634-7271 FAX: 214-634-8874
UTAH SALT LAKE CITY 2230 SOUTH MAIN STREET SALT LAKE CITY, UT 84115 PHONE: 801-832-0127 FAX: 801-832-8911
WISCONSIN MILWAUKEE 2725 SOUTH 163RD STREET NEW BERLIN, WI 53151 PHONE: 262-784-5940 FAX: 262-784-1215
INTERNATIONAL SALES FORT SMITH, AR BALDOR ELECTRIC CO FORT SMITH, AR 72902 PHONE: 479-646-4711 FAX: 479-648-5895
CANADA EDMONTON, ALBERTA 4053-92 STREET EDMONTON, ALBERTA T6E 6R8 PHONE: 780-434-4900 FAX: 780-438-2600
OAKVILLE, ONTARIO 2750 COVENTRY ROAD OAKVILLE, ONTARIO L6H 6R1 PHONE: 905-829-3301 FAX: 905-829-3302
MONTREAL, QUEBEC 1844 WILLIAM STREET MONTREAL, QUEBEC H3J 1R5 PHONE: 514-933-2711 FAX: 514-933-8639 VANCOUVER, BRITISH COLUMBIA 1538 KEBET WAY PORT COQUITLAM, BC V3C 5M5 PHONE 604-421-2822 FAX: 604-421-3113
WINNIPEG, MANITOBA 54 PRINCESS STREET WINNIPEG, MANITOBA R3B 1K2 PHONE: 204-942-5205 FAX: 204-956-4251
AUSTRALIA UNIT 3, 6 STANTON ROAD SEVEN HILLS, NSW 2147, AUSTRALIA PHONE: (61) (2) 9674 5455 FAX: (61) (2) 9674 2495
UNIT 8, 5 KELLETTS ROAD ROWVILLE, VICTORIA, 3178 AUSTRALIA PHONE: (61) (3) 9753 4355 FAX: (61) (3) 9753 4366
BALDOR CENTROAMERICA RESIDENCIAL PINARES DE SUIZA POL. 15 #44, NVA. SAN SALVADOR EL SALVADOR, CENTRO AMERICA PHONE: (503) 288-1519 FAX: (503) 288-1518
BALDOR SUDAMERICA 9109 0818, ZONA 6 BETHANIA PANAMÁ CITY, REP. DE PANAMÁ PHONE: (507) 261-5347 FAX: (507) 261-5355
CHINA SHANGHAI JIAHUA BUSINESS CENTER ROOM NO. A-8421 808 HONG QIAO ROAD SHANGHAI 200021 PHONE: 86-21-64473060 FAX: 86-21-64078620
UNITED STATES
ARIZONA PHOENIX 4211 S 43RD PLACE PHOENIX, AZ 85040 PHONE: 602-470-0407 FAX: 602-470-0464
CALIFORNIA LOS ANGELES 6480 FLOTILLA COMMERCE, CA 90040 PHONE: 323-724-6771 FAX: 323-721-5859
HAYWARD 21056 FORBES STREET HAYWARD, CA 94545 PHONE: 510-785-9900 FAX: 510-785-9910 COLORADO DENVER 2520 W BARBERRY PLACE DENVER, CO 80204 PHONE: 303-623-0127 FAX: 303-595-3772
CONNECTICUT WALLINGFORD 65 SOUTH TURNPIKE ROAD WALLINGFORD, CT 06492 PHONE: 203-269-1354 FAX: 203-269-5485
FLORIDA TAMPA/PUERTO RICO/ VIRGIN ISLANDS 3906 EAST 11TH AVENUE TAMPA, FL 33605 PHONE: 813-248-5078 FAX: 813-247-2984
GEORGIA ATLANTA 62 TECHNOLOGY DR. ALPHARETTA, GA 30005 PHONE: 770-772-7000 FAX: 770-772-7200
ILLINOIS CHICAGO 1601 FRONTENAC ROAD NAPERVILLE, IL 60563 PHONE: 630-848-5100 FAX: 630-848-5110
MEXICO CITY
BALDOR DISTRICT OFFICES
•EDMONTONVANCOUVER
• DISTRICT OFFICE & WAREHOUSES
PORTLAND
HAYWARD
LOS ANGELES
PHOENIX
MONTERREY
GUADALAJARA
TAMPA
FORT SMITH✫ MEMPHIS
WINNIPEG
ATLANTA
KANSAS CITY
ST LOUIS
DENVER
DES MOINES
GREENSBOROBALTIMORE
PITTSBURGH
CINCINNATIINDIANAPOLIS
DALLAS
CHICAGO
PHILADELPHIANEW YORK
BOSTONAUBURN
CLEVELAND
DETROIT TORONTOMINNEAPOLIS MILWAUKEE
GRAND RAPIDS SALT LAKE CITY
TULSA
• MONTREAL
HOUSTON
LEON
WALLINGFORD
•
•
•
• •
•
•
• ••• •• •
••••••• •
•
•• •
•
•
••
••
•
•
•
•••
