Industrial ProtectiveCoating Solutions

www.valsparindustrialmix.com.auV.12.13

INDUSTRIAL MIX

SYSTEM TECHNIQUES

CONTENTS

Applications Page

System Technique 33-1 433-1 54-1 644-1 744-2 85-1 95-3 1054-1 1154-2 1254-3 1354-4 1454-5 15544-1 16544-2 17544-3 1855-1 1955-2 2055-3 21754-1 22754-2 23754-3 24754-4 25

INDUSTRIAL MIX

Date of issue: 12/2013 These products are for professional use only! Page 3 of 25

System Technique

INDUSTRIAL MIX

Date of issue: 12/2013 These products are for professional use only! Page 4 of 25

Topcoat TB300 Synthetic Topcoat High Gloss TDS–Nr.: TB300/AU

Preparation and Pre-treatment Characteristics Iron, steel, cast iron, aluminum, glass fiber reinforced plastic, for plastic substrates – after suitability and adhesion test, use FP600 Plastic Primer. Hardened, solvent resistant surfaces, sanded original- and old paintwork.

Note: Only for inside – Coating without corrosion protection.

The durability of the coating system largely depends on the thoroughness of the preparation of the surface (for more detailed information about preparing, see the Technical Information “Preparation and Pre-treatment”).

1K Synthetic Topcoat Total layer thickness: 40-60µm Application Convertional gun, Brush, Roll Airless, Airmix

For more Information see our Technical Data Sheets.

Topcoat

Product Mixing ratio (Volume) Layers Dry times

TB300 Synthetic Topcoat High Gloss 100

15-30%

2 40-60µm

Dust dry: 20-30 min./20°C Dry to assembly: 5-7 hours/20°C Dry: 24 hours/20°C Force-dry: 30‘/60°C RS300 Synthetic Reducer

For a higher chemical resistance and faster drying, use AS300 Synthetic Activator (max.25% + 0-10% RS300 Synthetic Reducer can be added), instead of the Synthetic Reducer.

In case a Semi Gloss or Matt finish is required, it is possible to add max. 30% of AD300 Synthetic Matting Agent to the Topcoat. By adjusting the added % of Synthetic Matting Agent the gloss level can be reduced from High Gloss to Semi Gloss or Matt. In case of over 25% until 30% of Matting Agent add ½-1% AA300 Dryer extra. The Mixing ratio is the same, with Synthetic Reducer or Synthetic Activator.

For a higher thickness use AD309 Synthetic High Build Additive without Activator 50-100% and 15-30% Synthetic Reducer. With Activator: TB300 - 100 parts, Synthetic Activator – 25 parts, + 40-80% Synthetic High Build Additive, + 0-10% Reducer. Only for air-drying! Please, see the TDS for more information.

Information:

If you want to weigh the components by balance, please use our VIM-CRS software. For airless or air mix processing, follow the instructions on our technical data sheet. Further Information about the products mentioned can be found in our technical data sheets.

System Technique

Nº 3-1

Date of issue: 12/2013 These products are for professional use only! Page 5 of 25

Primer FP300 Synthetic Primer DTM Grey TDS–Nr.: FP300/AU

Topcoat TB300 Synthetic Topcoat High Gloss TDS-Nr.: TB300/AU

Preparation and Pre-treatment Characteristics Iron, steel, cast iron, aluminum, glass fiber reinforced plastic, for plastic substrates – after suitability and adhesion test, use FP600 Plastic Primer. Hardened, solvent resistant surfaces, sanded original- and old paintwork. The durability of the coating system largely depends on the thoroughness of the preparation of the surface (for more detailed information about preparing, see the Technical Information “Preparation and Pre-treatment”).

1K Synthetic Primer DTM 1K Synthetic Topcoat Total layer thickness: 40-60µm Application Convertional gun, Brush, Roll Airless, Airmix

For more Information see our Technical Data Sheets.

Primer Product Mixing ratio

(Volume) Layers Dry times

FP300 Synthetic Primer DTM Grey 100 1-2

40-60µm

Dust dry: 20 min./20°C Recoatable: 30-45 min./20°C Dry: 6-8 hours/20°C Force-dry: 20-30 min./60°C RS300 Synthetic Reducer 15-30

For a higher chemical resistance and faster drying, use AS300 Synthetic Activator (max.25% + 0-10% RS300 Synthetic Reducer can be added), instead of the Synthetic Reducer. Topcoat

Product Mixing ratio (Volume) Layers Dry times

TB300 Synthetic Topcoat High Gloss 100 2

40-60µm

Dust dry: 20‘-30‘/20°C Dry to assembly: 5-7 Std./20°C Dry: 24 Std./20°C Force-Dry: 30‘/60°C RS300 Synthetic Reducer 15-30

For a higher chemical resistance and faster drying, use AS300 Synthetic Activator (max.25% + 0-10% RS300 Synthetic Reducer can be added), instead of the Synthetic Reducer.

In case a Semi Gloss or Matt finish is required, it is possible to add max. 30% of AD300 Synthetic Matting Agent to the Topcoat. By adjusting the added % of Synthetic Matting Agent the gloss level can be reduced from High Gloss to Semi Gloss or Matt. In case of over 25% until 30% of Matting Agent add ½-1% AA300 Dryer extra. The Mixing ratio is the same, with Synthetic Reducer or Synthetic Activator.

For a higher thickness use AD309 Synthetic High Build Additive without Activator 50-100% and 15-30% Synthetic Reducer. With Activator: TB300 - 100 parts, Synthetic Activator – 25 parts, + 40-80% Synthetic High Build Additive, + 0-10% Reducer. Only for air-drying! Please, see the TDS for more information.

Information:

If you want to weigh the components by balance, please use our VIM-CRS software. For airless or air mix processing, follow the instructions on our technical data sheet. Further Information about the products mentioned can be found in our technical data sheets.

System Technique

Nº 33-1

Date of issue: 12/2013 These products are for professional use only! Page 6 of 25

Topcoat TB400 Epoxy Topcoat DTM High Gloss TDS–Nr.: IME.TB400/AU

Preparation and Pre-treatment Characteristics Iron, steel, cast iron, aluminum, glass fiber reinforced plastic, for plastic substrates – after suitability and adhesion test, use FP600 Plastic Primer. Hardened, solvent resistant surfaces, sanded original- and old paintwork.

Coating with higher chemical resistant. Note: Only for Indoor – not use outside!

The durability of the coating system largely depends on the thoroughness of the preparation of the surface (for more detailed information about preparing, see the Technical Information “Preparation and Pre-treatment”).

2K Epoxy Topcoat DTM Total layer thickness: 40-60µm Application Convertional gun, Airless, Airmix

For more Information see our Technical Data Sheets.

Topcoat

Product Mixing ratio (Volumen) Layers Dry times

TB400 Epoxy Topcoat DTM High Gloss 3 2

40-60µm

Dust dry: 40 min./20°C Dry to assembly: 5-7 hours/20°C Dry: 24 hours/20°C Force-dry: 30‘/60°C

AT400 Epoxy Activator 1

RS605* Universal Reducer + 25-30%

Note: RS60x* = All speeds of Reducers For a faster process of drying use AA600 Accelerator (max.5%).

Information:

If you want to weigh the components by balance, please use our VIM-CRS software. For airless or air mix processing, follow the instructions on our technical data sheet. Further Information about the products mentioned can be found in our technical data sheets.

System Technique

Nº 4-1

Date of issue: 12/2013 These products are for professional use only! Page 7 of 25

Primer FP400 Epoxy Primer DTM Grey TDS–Nr.: FP400/AU

Topcoat TB400 Epoxy Topcoat High Gloss TDS–Nr.: TB400/AU

Preparation and Pre-treatment Characteristics Iron, steel, stainless steel (blasted), galvanized steel, cast iron, aluminum, glass fiber reinforced plastic. For plastic substrates – after suitability and adhesion test, use FP600 Plastic Primer. Only for Indoor! Outside will the color pale after some weeks.

The durability of the coating system largely depends on the thoroughness of the preparation of the surface (for more detailed information about preparing, see the Technical Information “Preparation and Pre-treatment”).

2K Epoxy Primer DTM 2K Epoxy Topcoat Total layer thickness: 80-140µm Application Convertional gun, Airless, Airmix

For more Information see our Technical Information- and Data Sheets.

Primer

Product Mixing ratio (Volume) Layers Dry times

FP400 Epoxy Primer Grey 3 1-2

40-80µm

Dust Dry: 20 min./20°C Recoatable: 60‘ min.20°C W/W Dry: 10-16 hours/20°C Force-dry: 30-40 min./60°C

AP401 Epoxy Activator 1

RS405 Epoxy Reducer + 10-50%

As Sanding Primer use 10-30% Epoxy Reducer. Wet on wet application use 35-50% Epoxy Reducer / 1 layer 30-40µm. After 24 hours please, sand again. FP401 Epoxy Primer DTM is the same product only the color is white.

Topcoat

Product Mixing ratio (Volume) Layers Dry times

TB400 Epoxy Topcoat High Gloss 3 2

40-60µm

Dust dry: 40 min./20°C Dry to assembly: 5-7 hours/20°C Dry: 24 hours/20°C Force-dry: 30-40 min./60°C

AT400 Epoxy Activator 1

RS605* Universal Reducer + 25-30%

Note: RS60x* = All speeds of Reducers For a faster process of drying use AA600 Accelerator (max.5%).

Information:

If you want to weigh the components by balance, please use our VIM-CRS software. For airless or air mix processing, follow the instructions on our technical data sheet. Further Information about the products mentioned can be found in our technical data sheets. For recommended layer thickness, as per ISO 12944, see the information sheet TI-G9.

System Technique

Nº 44-1

ISO 12944 C4 > 15 years

C5 I/M 5 – 15 years

Date of issue: 12/2013 These products are for professional use only! Page 8 of 25

Primer FP402 Epoxy Primer Zinc Rich DTM Grey TDS–Nr.: FP402/AU

Topcoat TB400 Epoxy Topcoat High Gloss TDS–Nr.: TB400/AU

Preparation and Pre-treatment Characteristics Iron, steel – only blasted metal surfaces (SA 2½). Only for Indoor! Outside will the color pale after some weeks. The durability of the coating system largely depends on the thoroughness of the preparation of the surface (for more detailed information about preparing, see the Technical Information “Preparation and Pre-treatment”).

2K Epoxy Primer DTM 2K Epoxy Topcoat Total layer thickness: 80-140µm Application Convertional gun, Airless, Airmix

For more Information see our Technical Information- and Data Sheets.

Primer

Product Mixing ratio (Weight) Layers Dry times

FP402 Epoxy Primer Zinc Rich DTM Grey 1000 g 1-2

40-80µm

Dust dry: 20 min./20°C Recoatable: 60 min./20°C Dry: 10-16 hours/20°C Force-dry: 30-40 min./60°C

AP402 Epoxy Activator 84 g

RS405 Epoxy Reducer 25-60 g

As Sanding Primer use 25-40 g Epoxy Reducer. Wet on wet application use 40-60 g Epoxy Reducer / 1 layer 30-40µm. After 24 hours please, sand again.

Topcoat

Product Mixing ratio (Volume) Layers Dry times

TB400 Epoxy Topcoat High Gloss 3 2

40-60µm

Dust dry: 40 min./20°C Dry to assembly: 5-7 hours/20°C Dry: 24 hours/20°C Force-dry: 30-40 min./60°C

AT400 Epoxy Activator 1

RS605* Universal Reducer + 25-30%

Note: RS60x* = All speeds of Reducers For a faster process of drying use AA600 Accelerator (max.5%).

Information:

If you want to weigh the components by balance, please use our VIM-CRS software. For airless or air mix processing, follow the instructions on our technical data sheet. Further Information about the products mentioned can be found in our technical data sheets. For recommended layer thickness, as per ISO 12944, see the information sheet TI-G9.

System Technique

Nº 44-2

ISO 12944 C4 > 15 years

C5 I/M > 15 years

Date of issue: 12/2013 These products are for professional use only! Page 9 of 25

Topcoat TB540 PU Topcoat DTM High Gloss TDS–Nr.: TB540/AU

Preparation and Pre-treatment Characteristics Iron, steel, stainless steel (blasted), cast iron, galvanized steel, aluminum, glass fiber reinforced plastic. For plastic substrates – after suitability and adhesion test, use FP600 Plastic Primer. The durability of the coating system largely depends on the thoroughness of the preparation of the surface (for more detailed information about preparing, see the Technical Information “Preparation and Pre-treatment”).

2K Topcoat DTM High Gloss Total layer thickness: 40-65µm Application Convertional gun, Airless, Airmix

For more Information see our Technical Information- and Data Sheets.

Topcoat

Product Mixing ratio (Volume) Layers Dry times

TB540 PU Topcoat DTM High Gloss 4 2

40-65µm

Dust dry: 25-30 min./20°C Dry to assembly: 3-5 hours/20°C Dry: 8-10 hours/20°C Force-dry: 30 min./60°C

AU540 Polyurethane Activator 1

RS605* Universal Reducer +25%

Note: RS60x* = All speeds of Reducers For a faster process of drying use AA600 Accelerator (max.5%) For a higher thickness use AD600 High Build Additive (Mixing ratio is 4:1 + 40-80% Additive +10-25% Reducer, please see the TDS for more information).

Information:

If you want to weigh the components by balance, please use our VIM-CRS software. For airless or air mix processing, follow the instructions on our technical data sheet. Further Information about the products mentioned can be found in our technical data sheets.

System Technique

Nº 5-1

Date of issue: 12/2013 These products are for professional use only! Page 10 of 25

Topcoat TB543 PU Topcoat DTM Low Gloss TDS–Nr.: TB543/AU

Preparation and Pre-treatment Characteristics Iron, steel, stainless steel (blasted), cast iron, galvanized steel, aluminum, glass fiber reinforced plastic. For plastic substrates – after suitability and adhesion test, use FP600 Plastic Primer. The durability of the coating system largely depends on the thoroughness of the preparation of the surface (for more detailed information about preparing, see the Technical Information “Preparation and Pre-treatment”).

2K Topcoat DTM Low Gloss Total layer thickness: 40-65µm Application Convertional gun, Airless, Airmix

For more Information see our Technical Information- and Data Sheets.

Topcoat

Product Mixing ratio (Volume) Layers Dry times

TB543 PU Topcoat DTM High Gloss 4 2

40-65µm

Dust dry: 25-30 min./20°C Dry to assembly: 3-5 hours/20°C Dry: 8-10 hours/20°C Force-dry: 30 min./60°C

AU540 Polyurethane Activator 1

RS605* Universal Reducer + 0-25%

Note: RS60x* = All speeds of Reducers For a faster process of drying use AA600 Accelerator (max.5%) For a higher thickness use AD600 High Build Additive (Mixing ratio is 4:1 + 40-80% Additive +10-25% Reducer, please see the TDS for more information).

Information:

If you want to weigh the components by balance, please use our VIM-CRS software. For airless or air mix processing, follow the instructions on our technical data sheet. Further Information about the products mentioned can be found in our technical data sheets.

System Technique

Nº 5-3

Date of issue: 12/2013 These products are for professional use only! Page 11 of 25

Primer FP400 Epoxy Primer DTM Grey TDS–Nr.: FP400/AU

Topcoat TB500 PU Topcoat Performance High Gloss TDS–Nr.: TB500/AU

Preparation and Pre-treatment Characteristics Iron, steel, stainless steel (substrate blasted), cast iron, galvanized steel, aluminum, glass fiber reinforced plastic. Hardened, solvent resistant surfaces, sanded original- and old paintwork. For plastic substrates – after suitability and adhesion test, use FP600 Plastic Primer.

The durability of the coating system largely depends on the thoroughness of the preparation of the surface (for more detailed information about preparing, see the Technical Information “Preparation and Pre-treatment”).

2K Epoxy Primer DTM 2K PU Topcoat Total layer thickness: 80-140µm Application Convertional gun, Airless, Airmix

For more Information see our Technical Information- and Data Sheets.

Primer

Product Mixing ratio (Volume) Layers Dry times

FP400 Epoxy Primer DTM Grey 3 1-2

40-80µm

Dust dry: 20 min./20°C Recoatable: 1-24 hours/20°C Dry: 10-16 hours/20°C Force-dry: 30-40 min./60°C

AP401 Epoxy Activator 1

RS405 Epoxy Reducer + 10-50%

As Sanding Primer use 10-30% Epoxy Reducer. Wet on wet application use 35-50% Epoxy Reducer / 1 layer 30-40µm. After 24 hours please, sand again. FP401 Epoxy Primer DTM is the same product only the color is white.

Topcoat

Product Mixing ratio (Volume) Layers Dry times

TB500 PU Topcoat Performance High Gloss (VOC <420g/l) 4

2 40-65µm

Dust dry: 60-90 min./20°C Dry to assembly: 5-7 hours/20°C Dry: 24 hours/20°C Force-dry: 30-40 min./60°C

AU500 Polyurethane Activator 1

RS605* Universal Reducer + 0-5%

Note: RS60x* = All speeds of Reducers For a faster process of drying use AA600 Accelerator instead of IME.RS605 Universal Reducer.

Information:

If you want to weigh the components by balance, please use our VIM-CRS software. For airless or air mix processing, follow the instructions on our technical data sheet. Further Information about the products mentioned can be found in our technical data sheets. For recommended layer thickness, as per ISO 12944, see the information sheet TI-G9.

System Technique

Nº 54-1

ISO 12944 C4 > 15 years

C5 I/M 5 - 15 years

Date of issue: 12/2013 These products are for professional use only! Page 12 of 25

Primer FP402 Epoxy Primer Zinc Rich TDS–Nr.: FP402/AU

Topcoat TB500 PU Topcoat Performance High Gloss TDS–Nr.: TB500/AU

Preparation and Pre-treatment Characteristics Iron, steel – only blasted metal surfaces (SA 2½). The durability of the coating system largely depends on the thoroughness of the preparation of the surface (for more detailed information about preparing, see the Technical Information “Preparation and Pre-treatment”).

2K Epoxy Primer 2K PU Topcoat Total layer thickness: 80-140µm Application Convertional gun, Airless, Airmix

For more Information see our Technical Information- and Data Sheets.

Primer

Product Mixing ratio (Weight) Layers Dry times

FP402 Epoxy Primer Zinc Rich Grey 1000 g 1-2

40-80µm

Dust dry: 20 min./20°C Recoatable: 60 min./20°C w/w Dry: 10-16 hours/20°C Force-dry: 30-40 min./60°C

AP402 Epoxy Activator 84 g

RS405 Epoxy Reducer 25-60 g

As Sanding Primer use 25-40 g Epoxy Reducer. Wet on wet application use 40-60 g Epoxy Reducer / 1 layer 30-40µm. After 24 hours please, sand again.

Topcoat

Product Mixing ratio (Volume) Layers Dry times

TB500 PU Topcoat Performance High Gloss (VOC <420g/l) 4

2 40-65µm

Dust dry: 60-90 min./20°C Dry to assembly: 5-7 hours/20°C Dry: 24 hours/20°C Force-dry: 30-40 min./60°C

AU500 Polyurethane Activator 1

RS605* Universal Reducer + 0-5%

Note: RS60x* = All speeds of Reducers For a faster process of drying use AA600 Accelerator instead of IME.RS605 Universal Reducer.

Information:

If you want to weigh the components by balance, please use our VIM-CRS software. For airless or air mix processing, follow the instructions on our technical data sheet. Further Information about the products mentioned can be found in our technical data sheets. For recommended layer thickness, as per ISO 12944, see the information sheet TI-G9.

System Technique

Nº 54-2

ISO 12944 C4 > 15 years

C5 I/M > 15 years

Date of issue: 12/2013 These products are for professional use only! Page 13 of 25

Primer FP400 Epoxy Primer DTM Grey TDS–Nr.: FP400/AU

Topcoat TB520 PU Topcoat Basic High Gloss TDS–Nr.: TB520/AU

Preparation and Pre-treatment Characteristics Iron, steel, stainless steel (substrate blasted), cast iron, galvanized steel, aluminum, glass fiber reinforced plastic. Hardened, solvent resistant surfaces, sanded original- and old paintwork. For plastic substrates – after suitability and adhesion test, use FP600 Plastic Primer.

The durability of the coating system largely depends on the thoroughness of the preparation of the surface (for more detailed information about preparing, see the Technical Information “Preparation and Pre-treatment”).

2K Epoxy Primer 2K PU Topcoat Total layer thickness: 80-140µm Application Convertional gun, Airless, Airmix

For more Information see our Technical Information- and Data Sheets.

Primer

Product Mixing ratio (Volume) Layers Dry times

FP400 Epoxy Primer Grey 3 1-2

40-80µm

Dust dry: 20 min./20°C Recoatable: 1-24 hours/20°C Dry: 10-16 hours/20°C Force-dry: 30-40 min./60°C

AP401 Epoxy Activator 1

RS405 Epoxy Reducer + 10-50%

As Sanding Primer use 10-30% Epoxy Reducer. Wet on wet application use 35-50% Epoxy Reducer / 1 layer 30-40µm. After 24 hours please, sand again. FP401 Epoxy Primer DTM is the same product only the color is white.

Topcoat

Product Mixing ratio (Volume) Layers Dry times

TB520 PU Topcoat Basic High Gloss 6 2

40-60µm

Dust dry: 15-20 min./20°C Dry to assembly: 2-4 hours/20°C Dry: 8-10 hours/20°C Force-dry: 20-30 min./60°C

AU500 Polyurethane Activator 1

RS605* Universal Reducer + 20-35%

Note: RS60x* = All speeds of Reducers For a very fast process of drying use AA600 Accelerator (max.5%) For a higher thickness use AD600 High Build Additive Mixing ratio is 6:1 + 40-80% Additive and + 20-35% Reducer. Please, see the TDS for more information.

Information:

If you want to weigh the components by balance, please use our VIM-CRS software. For airless or air mix processing, follow the instructions on our technical data sheet. Further Information about the products mentioned can be found in our technical data sheets. For recommended layer thickness, as per ISO 12944, see the information sheet TI-G9.

System Technique

Nº 54-3

ISO 12944 C4 > 15 years

C5 I/M 5 - 15 years

Date of issue: 12/2013 These products are for professional use only! Page 14 of 25

Primer FP402 Epoxy Primer Zinc Rich DTM TDS-Nr.: FP402/AU

Topcoat TB520 PU Topcoat Basic High Gloss TDS–Nr.: TB520/AU

Preparation and Pre-treatment Characteristics Iron, steel – only blasted metal surfaces (SA 2½). The durability of the coating system largely depends on the thoroughness of the preparation of the surface (for more detailed information about preparing, see the Technical Information “Preparation and Pre-treatment”).

2K Epoxy Primer 2K PU Topcoat Total layer thickness: 80-140µm Application Convertional gun, Airless, Airmix

For more Information see our Technical Information- and Data Sheets.

Primer

Product Mixing ratio (Weight) Layers Dry times

FP402 Epoxy Primer Zinc Rich DTM Grey 1000 g 1-2

40-80µm

Dust dry: 20 min./20°C Recoatable: 1-24 hours/20°C Dry: 10-16 hours/20°C Force-dry: 30-40 min./60°C

AP402 Epoxy Activator 84 g

RS405 Epoxy Reducer 25-60 g

As Sanding Primer use 25-40 g Epoxy Reducer. Wet on wet application use 40-60 g Epoxy Reducer / 1 layer 30-40µm. After 24 hours please, sand again.

Topcoat

Product Mixing ratio (Volume) Layers Dry times

TB520 PU Topcoat Basic High Gloss 6 2

40-60µm

Dust dry: 15-20 min./20°C Dry to assembly: 2-4 hours/20°C Dry: 8-10 hours/20°C Force-dry: 20-30 min./60°C

AU500 Polyurethane Activator 1

RS605* Universal Reducer + 20-35%

Note: RS60x* = All speeds of Reducers For a very fast process of drying use AA600 Accelerator (max.5%). For a higher thickness use AD600 High Build Additive Mixing ratio is 6:1 + 40-80% Additive and + 20-35% Reducer. Please, see the TDS for more information.

Information:

If you want to weigh the components by balance, please use our VIM-CRS software. For airless or air mix processing, follow the instructions on our technical data sheet. Further Information about the products mentioned can be found in our technical data sheets. For recommended layer thickness, as per ISO 12944, see the information sheet TI-G9.

System Technique

Nº 54-4

ISO 12944 C4 > 15 years

C5 I/M > 15 years

Date of issue: 12/2013 These products are for professional use only! Page 15 of 25

Primer FP400 Epoxy Primer DTM Grey TDS–Nr.: FP400/AU

Topcoat TB510 PU Topcoat DTM High Gloss TDS–Nr.: TB510/AU

Preparation and Pre-treatment Characteristics Iron, steel, stainless steel (substrate blasted), cast iron, galvanized steel, aluminum, glass fiber reinforced plastic. Hardened, solvent resistant surfaces, sanded original- and old paintwork. For plastic substrates – after suitability and adhesion test, use FP600 Plastic Primer.

The durability of the coating system largely depends on the thoroughness of the preparation of the surface (for more detailed information about preparing, see the Technical Information “Preparation and Pre-treatment”).

2K Epoxy Primer DTM 2K PU Topcoat DTM Total layer thickness: 100-180µm Application Convertional gun, Airless, Airmix

For more Information see our Technical Information- and Data Sheets.

Primer

Product Mixing ratio (Volume) Layers Dry times

FP400 Epoxy Primer Grey 3 1-2

40-80µm

Dust dry: 20 min./20°C Recoatable: 1-24 hours/20°C Dry: 10-16 hours/20°C Force-dry: 30-40 min./60°C

AP401 Epoxy Activator 1

RS405 Epoxy Reducer + 10-50%

As Sanding Primer use 10-30% Epoxy Reducer. Wet on wet application use 35-50% Epoxy Reducer / 1 layer 30-40µm. After 24 hours please, sand again. FP401 Epoxy Primer DTM is the same product only the color is white.

Topcoat

Product Mixing ratio (Volume) Layers Dry times

TB510 PU Topcoat DTM High Gloss 5 2

50-80µm

Dust dry: 25-30 min./20°C Dry to assembly: 3-5 hours/20°C Dry: 8-10 hours/20°C Force-dry: 30 min./60°C

AU500 PU Activator 1

RS605* Universal Reducer + 10-20%

Note: RS60x* = All speeds of Reducers For a faster process of drying use AA600 Accelerator (max.5%) For a higher thickness use AD600 High Build Additive (Mixing ratio is 5:1 + 40-80% Additive and + 10-20% Reducer. It is also possible to use: TB511 PU Topcoat DTM Semi Gloss or TB512 PU Topcoat DTM Matt instead of TB510 PU Topcoat DTM High Gloss (mixing ratio is the same). Please, see the TDS for more information.

Information:

If you want to weigh the components by balance, please use our CRS software. For airless or air mix processing, follow the instructions on our technical data sheet. Further Information about the products mentioned can be found in our technical data sheets. For recommended layer thickness, as per ISO 12944, see the information sheet TI-G9.

System Technique

Nº 54-5

ISO 12944 C4 > 15 years

C5 I/M 5 - 15 years

Date of issue: 12/2013 These products are for professional use only! Page 16 of 25

Primer FP402 Epoxy Primer Zinc Rich DTM TDS–Nr.: FP402/AU

Primer FP400 Epoxy Primer DTM Grey TDS–Nr.: FP400/AU

Topcoat TB500 PU Topcoat Performance High Gloss TDS–Nr.: TB500/AU Preparation and Pre-treatment Characteristics Iron, steel – only blasted metal surfaces (SA 2½). The durability of the coating system largely depends on the thoroughness of the preparation of the surface (for more detailed information about preparing, see the Technical Information “Preparation and Pre-treatment”).

2K Epoxy Primer Zinc rich 2K Epoxy Primer 2K PU Topcoat (VOC <420g/l) Total layer thickness: 140-200µm Application Convertional gun, Airless, Airmix

For more Information see our Technical Information- and Data Sheets.

Primer

Product Mixing ratio (Weight) Layers Dry times

FP402 Epoxy Primer Zinc Rich DTM Grey 1000 g 1-2

40-80µm

Dust Dry: 20 min./20°C Recoatable: 60‘/20°C Dry: 10-16 hours/20°C Force-dry: 30-40 min./60°C

AP402 Epoxy Activator 84 g

RS405 Epoxy Reducer 25-60 g

As Sanding Primer use 25-40 g Epoxy Reducer. Wet on wet application use 40 g Epoxy Reducer / 1 layer 30-40µm. After 24 hours please, sand again.

Primer

Product Mixing ratio

(Volume) Layers Dry times

FP400 Epoxy Primer DTM Grey 3 1-2

40-80µm

Dust Dry: 20 min./20°C Recoatable: 60 min./20°C Dry: 10-16 hours/20°C Force-dry: 30-40 min./60°C

AP401 Epoxy Activator 1

RS405 Epoxy Reducer + 10-50%

As Sanding Primer use 10-30% Epoxy Reducer. Wet on wet application use 35-50% Epoxy Reducer / 1 layer 30-40µm. After 24 hours please, sand again. FP401 Epoxy Primer DTM is the same product only the color is white. For the best Quality and a smooth surface – sand after the drying time with Excenter machine P320-P400.

Topcoat

Product Mixing ratio (Volume) Layers Dry times

TB500 PU Topcoat Performance High Gloss (VOC <420g/l) 4

2 40-65µm

Dust dry: 60 min./20°C Dry to assembly: 12 hours/20°C Dry: 16-24 hours/20°C Force-dry: 30-40 min./60°C

AU500 Polyurethane Activator 1

RS605* Universal Reducer + 0-5%

Note: RS60x* = All speeds of Reducers For a faster process of drying use AA600 Accelerator instead of RS605 Universal Reducer.

Information:

If you want to weigh the components by balance, please use our VIM-CRS software. For airless or air mix processing, follow the instructions on our technical data sheet, Further Information about the products mentioned can be found in our technical data sheets. For recommended layer thickness, as per ISO 12944, see the information sheet TI-G9.

System Technique

Nº 544-1

ISO 12944 C4 > 15 years

C5 I/M > 15 years

Date of issue: 12/2013 These products are for professional use only! Page 17 of 25

Primer FP402 Epoxy Primer Zinc Rich DTM TDS–Nr.: FP402/AU

Primer FP400 Epoxy Primer DTM Grey TDS–Nr.: FP400/AU

Topcoat TB520 PU Topcoat Basic High Gloss TDS–Nr.: TB520/AU Preparation and Pre-treatment Characteristics Iron, steel – only blasted metal surfaces (SA 2½). The durability of the coating system largely depends on the thoroughness of the preparation of the surface (for more detailed information about preparing, see the Technical Information “Preparation and Pre-treatment”).

2K Epoxy Primer Zinc rich 2K Epoxy Primer 2K PU Topcoat Total layer thickness: 140-200µm Application Convertional gun, Airless, Airmix

For more Information see our Technical Information- and Data Sheets.

Primer

Product Mixing ratio (Weight) Layers Dry times

FP402 Epoxy Primer Zinc Rich DTM Grey 1000 g 1-2

40-80µm

Dust Dry: 20 min./20°C Recoatable: 60‘/20°C Dry: 10-16 hours/20°C Force-dry: 30-40 min./60°C

AP402 Epoxy Activator 84 g

RS405 Epoxy Reducer 25-60 g

As Sanding Primer use 25-40 g Epoxy Reducer. Wet on wet application use 40 g Epoxy Reducer / 1 layer 30-40µm. After 24 hours please, sand again.

Primer

Product Mixing ratio

(Volume) Layers Dry times

FP400 Epoxy Primer DTM Grey 3 1-2

40-80µm

Dust Dry: 20 min./20°C Recoatable: 60 min./20°C Dry: 10-16 hours/20°C Force-dry: 30-40 min./60°C

AP401 Epoxy Activator 1

RS405 Epoxy Reducer + 10-50%

As Sanding Primer use 10-30% Epoxy Reducer. Wet on wet application use 35-50% Epoxy Reducer / 1 layer 30-40µm. After 24 hours please, sand again. FP401 Epoxy Primer DTM is the same product only the color is white. For the best Quality and a smooth surface – sand after the drying time with Excenter machine P320-P400.

Topcoat

Product Mixing ratio (Volume) Layers Dry times

TB520 PU Topcoat Basic High Gloss 6 2

40-60µm

Dust dry: 15-20 min./20°C Dry to assembly: 2-4 hours/20°C Dry: 8-10 hours/20°C Force-dry: 20-30 min./60°C

AU500 Polyurethane Activator 1

RS605* Universal Reducer + 20-35%

Note: RS60x* = All speeds of Reducers For a faster process of drying use AA600 Accelerator, max. 5%.

Information:

If you want to weigh the components by balance, please use our VIM-CRS software. For airless or air mix processing, follow the instructions on our technical data sheet. Further Information about the products mentioned can be found in our technical data sheets. For recommended layer thickness, as per ISO 12944, see the information sheet TI-G9.

System Technique

Nº 544-2

ISO 12944 C4 > 15 years

C5 I/M > 15 years

Date of issue: 12/2013 These products are for professional use only! Page 18 of 25

Primer FP402 Epoxy Primer Zinc Rich DTM TDS–Nr.: FP402/AU

Primer FP400 Epoxy Primer DTM Grey TDS–Nr.: FP400/AU

Topcoat TB540 PU Topcoat DTM High Gloss TDS–Nr.: TB540/AU

Preparation and Pre-treatment Characteristics Iron, steel – only blasted metal surfaces (SA 2½). The durability of the coating system largely depends on the thoroughness of the preparation of the surface (for more detailed information about preparing, see the Technical Information “Preparation and Pre-treatment”).

2K Epoxy Primer Zinc rich 2K Epoxy Primer 2K PU Topcoat High Gloss Total layer thickness: 140-250µm Application Convertional gun, Airless, Airmix

For more Information see our Technical Information- and Data Sheets.

Primer

Product Mixing ratio (Weight) Layers Dry times

FP402 Epoxy Primer Zinc Rich DTM Grey 1000 g 1-2

40-80µm

Dust Dry: 20 min./20°C Recoatable: 60‘/20°C Dry: 10-16 hours/20°C Force-dry: 30-40 min./60°C

AP402 Epoxy Activator 84 g

RS405 Epoxy Reducer 25-60 g

As Sanding Primer use 25-40 g Epoxy Reducer. Wet on wet application use 40 g Epoxy Reducer / 1 layer 30-40µm. After 24 hours please, sand again.

Primer

Product Mixing ratio

(Volume) Layers Dry times

FP400 Epoxy Primer DTM Grey 3 1-2

40-80µm

Dust Dry: 20 min./20°C Recoatable: 60 min./20°C Dry: 10-16 hours/20°C Force-dry: 30-40 min./60°C

AP401 Epoxy Activator 1

RS405 Epoxy Reducer + 10-50%

As Sanding Primer use 10-30% Epoxy Reducer. Wet on wet application use 35-50% Epoxy Reducer / 1 layer 30-40µm. After 24 hours please, sand again. FP401 Epoxy Primer DTM is the same product only the color is white. For the best Quality and a smooth surface – sand after the drying time with 3mm Orbital sanding machine P320-P400.

Topcoat

Product Mixing ratio (Volume) Layers Dry times

TB540 PU Topcoat DTM High Gloss 4 2

40-65µm

Dust dry: 25-30 min./20°C Dry to assembly: 3-5 hours/20°C Dry: 8-10 hours/20°C Force-dry: 30 min./60°C

AU540 Polyurethane Activator 1

RS605* Universal Reducer + 25%

Note: RS60x* = All speeds of Reducers For a faster process of drying use AA600 Accelerator (max.5%) For a higher thickness use AD600 High Build Additive (Mixing ratio is 4:1 + 40-80% Additive and + 10-25% Reducer. It is also possible to use: TB543 PU Topcoat DTM Low Gloss instead of TB540 PU Topcoat DTM High Gloss (mixing ratio is the same). Please, see the TDS for more information.

Information:

If you want to weigh the components by balance, please use our VIM-CRS software. For airless or air mix processing, follow the instructions on our technical data sheet. Further Information about the products mentioned can be found in our technical data sheets.

System Technique

Nº 544-3

Date of issue: 12/2013 These products are for professional use only! Page 19 of 25

Primer FP500 PU Primer DTM Grey TDS–Nr.: FP500/AU

Topcoat TB500 PU Topcoat Performance High Gloss TDS–Nr.: TB500/AU Preparation and Pre-treatment Characteristics

Iron, steel, cast iron, galvanized steel, aluminum, glass fiber reinforced plastic. Hardened, solvent resistant surfaces, sanded original- and old paintwork. For plastic substrates – after suitability and adhesion test, use FP600 Plastic Primer.

The durability of the coating system largely depends on the thoroughness of the preparation of the surface (for more detailed information about preparing, see the Technical Information “Preparation and Pre-treatment”).

2K PU Primer DTM 2K PU Topcoat (VOC <420g/l) Total layer thickness: 80-140µm Application Convertional gun, Airless, Airmix

For more Information see our Technical Information- and Data Sheets.

Primer

Product Mixing ratio (Volume) Layers Dry times

FP500 PU Primer DTM Grey 8 1-2

40-80µm

Dust dry: 30 min./20°C Recoatable: 1-24 hours/20°C Dry: 10-14 hours/20°C Force-dry: 30-40 min./60°C

AU500 PU Activator 1

RS605* Universal Reducer + 10-25%

Note: RS60x* = All speeds of Reducers For a very fast process of drying use AA600 Accelerator (max. 3-5%). After 24 hours please, sanding again. PB500 PU Primer Binder DTM is the same product with the possibility to add. 20% Color Toner (see CRS), which color the user like.

Topcoat

Product Mixing ratio (Volume) Layers Dry times

TB500 PU Topcoat Performance High Gloss (VOC <420g/l) 4

2 40-65µm

Dust dry: 60 min./20°C Dry to assembly: 5-7 hours/20°C Dry: 24 hours/20°C Force-dry: 30-40 min./60°C

AU500 Polyurethane Activator 1

RS605* Universal Reducer + 0-5%

Note: RS60x* = All speeds of Reducers For a faster process of drying use AA600 Accelerator instead of RS605 Universal Reducer.

Information:

If you want to weigh the components by balance, please use our VIM-CRS software. For airless or air mix processing, follow the instructions on our technical data sheet. Further Information about the products mentioned can be found in our technical data sheets. For recommended layer thickness, as per ISO 12944, see the information sheet TI-G9.

System Technique

Nº 55-1

ISO 12944 C4 > 15 years

C5 I/M 5 - 15 years

Date of issue: 12/2013 These products are for professional use only! Page 20 of 25

Primer FP500 PU Primer DTM Grey TDS–Nr.: FP500/AU

Topcoat TB520 PU Topcoat Basic High Gloss TDS–Nr.: TB520/AU Preparation and Pre-treatment Characteristics

Iron, steel, cast iron, galvanized steel, aluminum, glass fiber reinforced plastic. Hardened, solvent resistant surfaces, sanded original- and old paintwork. For plastic substrates – after suitability and adhesion test, use FP600 Plastic Primer.

The durability of the coating system largely depends on the thoroughness of the preparation of the surface (for more detailed information about preparing, see the Technical Information “Preparation and Pre-treatment”).

2K PU Primer DTM 2K PU Topcoat Total layer thickness: 80-140µm Application Convertional gun, Airless, Airmix

For more Information see our Technical Information- and Data Sheets.

Primer

Product Mixing ratio (Volume) Layers Dry times

FP500 PU Primer DTM Grey 8 1-2

40-80µm

Dust dry: 20 min./20°C Recoatable: 1-24 hours/20°C Dry: 10-14 hours/20°C Force-dry: 30-40 min./60°C

AU500 PU Activator 1

RS605* Universal Reducer + 10-25%

Note: RS60x* = All speeds of Reducers For a very fast process of drying use AA600 Accelerator (max. 3-5%). After 24 hours please, sanding again. PB500 PU Primer Binder DTM is the same product with the possibility to add. 20% Color Toner (see CRS), which color the user like.

Topcoat

Product Mixing ratio (Volume) Layers Dry times

TB520 PU Topcoat Basic High Gloss 6 2

40-60µm

Dust dry: 15-20 min./20°C Dry to assembly: 2-4 hours/20°C Dry: 8-10 hours/20°C Force-dry: 20-30 min./60°C

AU500 Polyurethane Activator 1

RS605* Universal Reducer + 20-35%

Note: RS60x* = All speeds of Reducers For a very fast process of drying use AA600 Accelerator (max.5%). For a higher thickness use AD600 High Build Additive (Mixing ratio is 6:1 + 40-80% Additive and + 20-35% Reducer. Please, see the TDS for more information).

Information:

If you want to weigh the components by balance, please use our VIM-CRS software. For airless or air mix processing, follow the instructions on our technical data sheet. Further Information about the products mentioned can be found in our technical data sheets. For recommended layer thickness, as per ISO 12944, see the information sheet TI-G9.

System Technique

Nº 55-2

ISO 12944 C4 > 15 years

C5 I/M 5 - 15 years

Date of issue: 12/2013 These products are for professional use only! Page 21 of 25

Primer FP500 PU Primer DTM Grey TDS–Nr.: FP500/AU

Topcoat TB540 PU Topcoat DTM High Gloss TDS–Nr.: TB540/AU Preparation and Pre-treatment Characteristics

Iron, steel, cast iron, galvanized steel, aluminum, glass fiber reinforced plastic. Hardened, solvent resistant surfaces, sanded original- and old paintwork. For plastic substrates – after suitability and adhesion test, use FP600 Plastic Primer.

The durability of the coating system largely depends on the thoroughness of the preparation of the surface (for more detailed information about preparing, see the Technical Information “Preparation and Pre-treatment”).

2K PU Primer DTM 2K PU Topcoat DTM Total layer thickness: 100-180µm Application Convertional gun, Airless, Airmix

For more Information see our Technical Information- and Data Sheets.

Primer

Product Mixing ratio (Volume) Layers Dry times

FP500 PU Primer DTM Grey 8 1-2

40-80µm

Dust dry: 30 min./20°C Recoatable: 1-24 hours/20°C Dry: 10-14 hours/20°C Force-dry: 30-40 min./60°C

AU500 PU Activator 1

RS60x* Universal Reducer + 10-25%

Note: RS60x* = All speeds of Reducers For a very fast process of drying use AA600 Accelerator (max. 3-5%). After 24 hours please, sanding again. PB500 PU Primer Binder DTM is the same product with the possibility to add 20% Color Toner (see CRS).

Topcoat

Product Mixing ratio (Volume) Layers Dry times

TB540 PU Topcoat DTM High Gloss 4 2

50-80µm

Dust dry: 25-30 min./20°C Dry to assembly: 3-5 hours/20°C Dry: 8-10 hours/20°C Force-dry: 30 min./60°C

AU540 PU Activator 1

RS60x* Universal Reducer + 10-20%

Note: RS60x* = All speeds of Reducers For a faster process of drying use AA600 Accelerator (max.5%) For a higher thickness use AD600 High Build Additive (Mixing ratio is 5:1 + 40-80% Additive and + 10-20% Reducer). It is also possible to use: TB543 PU Topcoat DTM Matt instead of TB540 PU Topcoat DTM High Gloss (mixing ratio is the same). Please, see the TDS for more information.

Information:

If you want to weigh the components by balance, please use our CRS software. For airless or air mix processing, follow the instructions on our technical data sheet. Further Information about the products mentioned can be found in our technical data sheets. For recommended layer thickness, as per ISO 12944, see the information sheet TI-G9.

System Technique

Nº 55-3

Date of issue: 12/2013 These products are for professional use only! Page 22 of 25

Primer FP400 Epoxy Primer DTM TDS–Nr.: FP400/AU

Topcoat TB500 PU Topcoat Performance High Gloss TDS–Nr.: TB500/AU Clear coat CC700 Clear coat Anti Graffiti TDS–Nr.: CC700/AU Preparation and Pre-treatment Characteristics Iron, steel, stainless steel (blasted), cast iron, galvanized steel, aluminum, glass fiber reinforced plastic. Hardened, solvent resistant surfaces, sanded original- and old paintwork. For plastic substrates – after suitability and adhesion test, use FP600 Plastic Primer.

The durability of the coating system largely depends on the thoroughness of the preparation of the surface (for more detailed information about preparing, see the Technical Information “Preparation and Pre-treatment”).

2K Epoxy Primer DTM 2K Topcoat (VOC <420g/l) 2K Clear coat Total layer thickness: 140-200µm Application Convertional gun, Airless, Airmix

For more Information see our Technical Information- and Data Sheets.

Primer

Product Mixing ratio (Volume) Layers Dry times

FP400 Epoxy Primer DTM Grey 3 1-2

40-80µm

Dust dry: 20 min./20°C Recoatable: 60 min./20°C Dry: 10-16 hours/20°C Force-dry: 30-40 min./60°C

AP401 Epoxy Activator 1

RS405 Epoxy Reducer + 10-50%

As Sanding Primer use 10-30% Epoxy Reducer. Wet on wet application use 35-50% Epoxy Reducer / 1 layer 30-40µm. After 24 hours please, sanding again. FP401 Epoxy Primer DTM is the same product only the color is white.

Topcoat

Product Mixing ratio (Volume) Layers Dry times

TB500 PU Topcoat Performance High Gloss 4 2

40-65µm

Dust dry: 60 min./20°C Recoatable: 1-24 hours/20°C Dry: 12-16 hours/20°C Force-dry: 30-40 min./60°C

AU500 Polyurethane Activator 1

RS605* Universal Reducer + 0-5%

Note: RS60x* = All speeds of Reducers For a faster process of drying use AA600 Accelerator instead of IME.RS605 Universal Reducer. For a very good finish apply the CC700 Clear Coat after drying time (till 24 hours without sanding, after 24 hours sand again – Scotch-brite very fine/ultra fine).

Clear coat

Product Mixing ratio (Volume) Layers Dry times

CC700 Clear coat Anti Graffiti 2 2

40-60µm

Dust dry: 60 min./20°C Dry to assembly: 8-10 hours/20°C Dry: 24 hours/20°C Force-dry: 40-50 min./60°C

AU570 Clear coat Activator 1

RS605* Universal Reducer + 10-20%

Note: RS60x* = All speeds of Reducers For a faster process of drying use AA600 Accelerator (max.5%).

Information:

If you want to weigh the components by balance, please use our VIM-CRS software. For airless or air mix processing, follow the instructions on our technical data sheet. Further Information about the products mentioned can be found in our technical data sheets. For recommended layer thickness, as per ISO 12944, see the information sheet TI-G9.

System Technique

Nº 754-1

ISO 12944 C4 > 15 years

C5 I/M 5 - 15 years

Date of issue: 12/2013 These products are for professional use only! Page 23 of 25

Primer FP402 Epoxy Primer Zinc rich DTM TDS–Nr.: FP402/AU

Topcoat TB500 PU Topcoat Performance High Gloss TDS–Nr.: TB500/AU Clear coat CC700 Clear coat Anti Graffiti TDS–Nr.: CC700/AU Preparation and Pre-treatment Characteristics Iron, steel, stainless steel (blasted), cast iron, galvanized steel, aluminum, glass fiber reinforced plastic. Hardened, solvent resistant surfaces, sanded original- and old paintwork. For plastic substrates – after suitability and adhesion test, use FP600 Plastic Primer.

The durability of the coating system largely depends on the thoroughness of the preparation of the surface (for more detailed information about preparing, see the Technical Information “Preparation and Pre-treatment”).

2K Epoxy Primer DTM 2K Topcoat (VOC420g/l) 2K Clear coat Total layer thickness: 140-200µm Application Convertional gun, Airless, Airmix

For more Information see our Technical Information- and Data Sheets.

Primer

Product Mixing ratio (Weight) Layers Dry times

FP402 Epoxy Primer Zinc rich DTM Grey 1000 g 1-2

40-80µm

Dust dry: 20 min./20°C Recoatable: 60’/20°C Dry: 10-16 hours/20°C Force-dry: 30-40 min./60°C

AP402 Activator 84 g

RS405 Epoxy Reducer 25-60 g

As Sanding Primer use 25-40 g Epoxy Reducer. Wet on wet application use 40-60 g Epoxy Reducer / 1 layer 30-40µm. After 24 hours please, sanding again.

Topcoat

Product Mixing ratio (Volume) Layers Dry times

TB500 PU Topcoat Performance High Gloss 4 2

40-65µm

Dust dry: 60 min./20°C Recoatable: 1-24 hours/20°C Dry: 12-16 hours/20°C Force-dry: 30-40 min./60°C

AU500 Polyurethane Activator 1

RS605* Universal Reducer + 0-5%

Note: RS60x* = All speeds of Reducers For a faster process of drying use AA600 Accelerator instead of IME.RS605 Universal Reducer. For a very good finish apply the CC700 Clear Coat after drying time (till 24 hours without sanding, after 24 hours sand again – Scotch-brite very fine/ultra fine).

Clear coat

Product Mixing ratio (Volume) Layers Dry times

CC700 Clear coat Anti Graffiti 2 2

40-60µm

Dust dry: 60 min./20°C Dry to assembly: 8-10 hours/20°C Dry: 24 hours/20°C Force-dry: 40-50 min./60°C

AU570 Clear coat Activator 1

RS605* Universal Reducer + 10-20%

Note: RS60x* = All speeds of Reducers For a faster process of drying use AA600 Accelerator (max.5%).

Information:

If you want to weigh the components by balance, please use our VIM-CRS software. For airless or air mix processing, follow the instructions on our technical data sheet. Further Information about the products mentioned can be found in our technical data sheets. For recommended layer thickness, as per ISO 12944, see the information sheet TI-G9.

System Technique

Nº 754-2

ISO 12944 C4 > 15 years

C5 I/M > 15 years

Date of issue: 12/2013 These products are for professional use only! Page 24 of 25

Primer FP400 Epoxy Primer DTM TDS–Nr.: FP400/AU

Topcoat TB520 PU Topcoat Basic High Gloss TDS–Nr.: TB520/AU Clear coat CC700 Clear coat Anti Graffiti TDS–Nr.: CC700/AU Preparation and Pre-treatment Characteristics Iron, steel, stainless steel (blasted), cast iron, galvanized steel, aluminum, glass fiber reinforced plastic. Hardened, solvent resistant surfaces, sanded original- and old paintwork. For plastic substrates – after suitability and adhesion test, use FP600 Plastic Primer.

The durability of the coating system largely depends on the thoroughness of the preparation of the surface (for more detailed information about preparing, see the Technical Information “Preparation and Pre-treatment”).

2K Epoxy Primer DTM 2K PU Topcoat 2K Clear coat Total layer thickness: 140-200µm Application Convertional gun, Airless, Airmix

For more Information see our Technical Information- and Data Sheets.

Primer

Product Mixing ratio (Volume) Layers Dry times

FP400 Epoxy Primer DTM Grey 3 1-2

40-80µm

Dust dry: 20 min./20°C Recoatable: 60 min./20°C Dry: 10-16 hours/20°C Force-dry: 30-40 min./60°C

AP401 Epoxy Activator 1

RS405 Epoxy Reducer + 10-50%

As Sanding Primer use 10-30% Epoxy Reducer. Wet on wet application use 35-50% Epoxy Reducer / 1 layer 30-40µm. After 24 hours please, sanding again. FP401 Epoxy Primer DTM is the same product only the color is white.

Topcoat Product Mixing ratio

(Volume) Layers Dry times

TB520 PU Topcoat Basic High Gloss 6 2

40-60µm

Dust dry: 15-20 min./20°C Recoatable: 1-24 hours/20°C Dry: 8-10 hours/20°C Force-dry: 20-30 min./60°C

AU500 Polyurethane Activator 1

RS605* Universal Reducer + 20-35%

Note: RS60x* = All speeds of Reducers For a very good finish apply the CC700 Clear Coat after drying time (till 24 hours without sanding, after 24 hours sand again – Scotch-brite very fine/ultra fine).

Clear coat

Product Mixing ratio (Volume) Layers Dry times

CC700 Clear coat Anti Graffiti 2 2

40-60µm

Dust dry: 60 min./20°C Dry to assembly: 8-10 hours/20°C Dry: 24 hours/20°C Force-dry: 40-50 min./60°C

AU570 Clear coat Activator 1

RS605* Universal Reducer + 10-20%

Note: RS60x* = All speeds of Reducers For a faster process of drying use AA600 Accelerator (max.5%).

Information:

If you want to weigh the components by balance, please use our VIM-CRS software. For airless or air mix processing, follow the instructions on our technical data sheet. Further Information about the products mentioned can be found in our technical data sheets. For recommended layer thickness, as per ISO 12944, see the information sheet TI-G9.

System Technique

Nº 754-3

ISO 12944 C4 > 15 years

C5 I/M 5 - 15 years

Date of issue: 12/2013 These products are for professional use only! Page 25 of 25

Primer FP402 Epoxy Primer Zinc rich DTM TDS–Nr.: FP402/AU

Topcoat TB520 PU Topcoat Basic High Gloss TDS–Nr.: TB520/AU Clear coat CC700 Clear coat Anti Graffiti TDS–Nr.: CC700/AU Preparation and Pre-treatment Characteristics Iron, steel, stainless steel (blasted), cast iron, galvanized steel, aluminum, glass fiber reinforced plastic. Hardened, solvent resistant surfaces, sanded original- and old paintwork. For plastic substrates – after suitability and adhesion test, use FP600 Plastic Primer.

The durability of the coating system largely depends on the thoroughness of the preparation of the surface (for more detailed information about preparing, see the Technical Information “Preparation and Pre-treatment”).

2K Epoxy Primer DTM 2K PU Topcoat 2K Clear coat Total layer thickness: 140-200µm Application Convertional gun, Airless, Airmix

For more Information see our Technical Information- and Data Sheets.

Primer

Product Mixing ratio (Weight) Layers Dry times

FP402 Epoxy Primer Zinc rich DTM Grey 1000 g 1-2

40-80µm

Dust dry: 20 min./20°C Recoatable: 60’/20°C Dry: 10-16 hours/20°C Force-dry: 30-40 min./60°C

AP402 Activator 84 g

RS405 Epoxy Reducer 25-60 g

As Sanding Primer use 25-40 g Epoxy Reducer. Wet on wet application use 40-60 g Epoxy Reducer / 1 layer 30-40µm. After 24 hours please, sanding again.

Topcoat

Product Mixing ratio (Volume) Layers Dry times

TB520 PU Topcoat Basic High Gloss 6 2

40-60µm

Dust dry: 15-20 min./20°C Recoatable: 1-24 hours/20°C Dry: 8-10 hours/20°C Force-dry: 20-30 min./60°C

AU500 Polyurethane Activator 1

RS605* Universal Reducer + 20-35%

Note: RS60x* = All speeds of Reducers For a very good finish apply the CC700 Clear Coat after drying time (till 24 hours without sanding, after 24 hours sand again – Scotch-brite very fine/ultra fine).

Clear coat

Product Mixing ratio (Volume) Layers Dry times

CC700 Clear coat Anti Graffiti 2 2

40-60µm

Dust dry: 60 min./20°C Dry to assembly: 8-10 hours/20°C Dry: 24 hours/20°C Force-dry: 40-50 min./60°C

AU570 Clear coat Activator 1

RS605* Universal Reducer + 10-20%

Note: RS60x* = All speeds of Reducers For a faster process of drying use AA600 Accelerator (max.5%).

Information:

If you want to weigh the components by balance, please use our VIM-CRS software. For airless or air mix processing, follow the instructions on our technical data sheet. Further Information about the products mentioned can be found in our technical data sheets. For recommended layer thickness, as per ISO 12944, see the information sheet TI-G9.

System Technique

Nº 754-4

ISO 12944 C4 > 15 years

C5 I/M > 15 years

Date of issue: 12/2013 These products are for professional use only! Page 26 of 25

NOTES:............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

Date of issue: 12/2013 These products are for professional use only! Page 27 of 25

NOTES:............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

Date of issue: 12/2013 These products are for professional use only! Page 28 of 25

Valspar Automotive Australasia Pty Ltd11/8 Kerta Road

Kincumber NSW 2251AUSTRALIA

T 02 4368 4054F 02 4368 4215

valsparindustrialmix.com.auINDUSTRIAL MIX