• Power on the game. A splash screen momentarily appears with the Trestle logo. The GAME SCREEN then appears.
Figure 1
Initial Machine Setup • Press and hold the “SETUP BUTTON” and the “PLAY BUTTON” at the same time to
open up the “TOUCH SCREEN MENU” (Figure 2).
Figure 2
• Press “SETUP BUTTON” only to select the Touch Screen Brand menu.
Figure 3
• Click the arrows to reveal the alternate Touch /screen protocols. Click again on the
protocol of choice. Finally, click apply.
Figure 4
• Press and hold the “PLAY BUTTON” to bring up the “TOUCH SCREEN Calibration” menu.
Figure 5
• Click the ”CALIBRATE button to bring up the upper left side calibration target menu. The Touch screen must already be connected before powering on the machine.
Figure 6
• Press and hold your fingertip onto the center of the green Target symbol below the “touch here text” in the upper left quadrant. Continue pressing until the green OK appears.
Figure 7
• The right side green target menu appears.
Figure 8
9. Press and hold your fingertip onto the center of the green Target symbol below the “touch here text” in the lower right quadrant. Continue pressing until the green OK appears
.
Figure 9
• The Test screen appears.
Figure 10
• Test the screen by dragging your finger or taping it on various points on the
screen. Lines or dots will appear on points as touched. Click or touch the clear button to erase the marks.
Figure 11
• Click or touch the back button to return to the touch screen menu (see figure three). Click or touch the “APPLY BUTTON” if satisfied with the changes
Figure 12
• Touch the “BACK” button and the “INITIAL PASSWORD” menu” appears.
• Enter the default password 1-2-3-4 and the “MAIN MENU” appears.
Figure 14
1. Press the “BOOKKEEPING” button. The “BOOKKEEPING” menu appears. There is a “MASTER” tab for overall game accounting (Figure 15) and a “GAME” tab for individual game accounting (figure 16). Press the clear history button to reset the numbers to zero.
Figure 15
Figure 16
MASTER TAB: 1. Press the “Setting” button. The “SETTING” menu with 4 main tabs appears. Note! Always press the “SAVE” Button before leaving any “SETTING” tab or changes will not be saved.
Figure 21
this needs to be payo 3. SHOW CURRENCY VALUE: Touch the arrow to select yes or no. Yes: means 1 dollar (equivalent to 1.00). No: means 1 dollar (equivalent to 100). Touch the “SAVE” button before leaving the menu screen.
Figure 22
4. PULSE VALUE IN: Touch the arrow to select the “PULSE VALUE OUT” increment. The default is 1.00.
Figure 23
5. PULSE VALUE OUT: Touch the arrow to select the “PULSE VALUE OUT” increment. The default is 0.10.
Figure 24
6. SYSTEM DATE: Touch the arrows to select options. Pull the slider to reveal optional years. Touch the year to select. Touch the month arrows to set the month of the year. Touch the month to select. Pull the slider to reveal months. Touch to select the day of the year. Pull the slider to reveal days. Touch the selected day.
Figure 25
7. SYSTEM TIME: Touch the year arrows to set time. Pull the slider down to reveal the additional times. (Missing time screenshot).
8. SYSTEM VOLUMES and DEMO VOLUME. The “SYSTEM VOLUME” Default is 8. The DEMO VOLUME” is adjusted in percentages relative to system volume. Pull the slider of each to make adjustments.
Figure 26
SUPER BALL TAB: 1. Touch the “SUPER BALL” Tab and the SUPER BALL MENU appears.
Figure 27
• Touch the “MIN PLAY” arrows to reveal the drop down menu with optional min play increments. Touch to select the value desired.
Figure 28
• Touch the “MAX PLAY” arrows to reveal the drop down menu with optional max play increments. Touch to select the value desired.
Figure 29
• Touch the “PLAY INCREMENT” arrows to reveal the drop down menu with optional play increments. Touch to select the value desired.
Figure 30
• Touch the “JACKPOT START” arrows to reveal the drop down menu with optional
Jackpot Start increments. Touch to select the value desired.
Figure 31
• Touch the “JACKPOT LIMIT” arrows to reveal the drop down menu with optional
Jackpot Limit increments. Touch to select the value desired.
Figure 32
• Touch the “JACKPOT” arrows to reveal the drop down menu with optional Jackpot percentage increments. Touch to select the value desired.
Figure 33
8. Touch the “DEMONSTRATION” arrows to reveal the drop down menu with optional Jackpot percentage increments. Touch to select the value desired. The Default is “YES.”
Figure 34
BILL ACCEPTOR TAB: • Touch the “BILL ACCEPTOR” tab to reveal the “BILL ACCEPTOR “ menu.
Figure 35
• Touch the “MODEL” arrows to reveal optional bill acceptor protocol settings. Touch to select desired protocol/model. The default is ICT PA7.
Figure 36
PRINTER TAB:
• Touch the “PRINTER” tab to reveal the “PRINTER” menu.
Figure 37
2. Touch the “MODEL” arrows to reveal the drop down menu of optional printers. The default is ICT GP-58CR.
Figure 38
1. Touch the “UPDATE” button. The update menu will appear. Touch “REFRESH” if the new firmware is not detected. *
Figure 45
2. When the update is detected, a Green text message appears: ” The following update data was found.” Touch the “update” button to initiate the process.
Figure 46
• When the update process begins a green progress bar appears with a red warning, “ Please do not power off or unplug USB flash drive.”
Figure 47
4. A successful update will generate the message: “software will restart.” The machine reboots the machine automatically (missing Screenshot)
Touch the “LAST REDEEM” button and the “LAST REDEEM” menu appears. This menu allows you to reprint the last printed receipt (See Figure 34). Press the ”PRINT “ button and a copy labeled as a duplicate will be reprinted (see Figure 35).
Figure 48
Figure 49
IO TEST OVERVIEW • Touch the IO Test and the IO menu appears. This menu allows the operator to set
parameters of peripherals such as Printer and bill acceptor.
Figure 50
• Touch the “CHANGE PASSWORD” Button to reveal the Change Password menu.
Figure 52
• Enter the old password in the “Old Password” text field. • Enter the new password in the “New Password” text field. • Re-enter the new password in the Confirm Password Field • Touch apply (need screenshot of settings saved and error message)
