INSIDE MEASURING INSTRUMENTS - J.W. Donchin Cojwdonchin.com/Mitutoyo/Catalog/InsideMics.pdfMITUTOYO...

MITUTOYO - INSIDE MEASURING INSTRUMENTS

INSIDE MEASURING INSTRUMENTSInside Micrometers - Series 345, 145 N-2,3Inside Micrometers - Series 141 - Interchangeable Type N-4.5Tubular Inside Micrometers - Series 337, 137 - Extension Type N-6, 7Tubular Inside Micrometers - Series 339, 139, 140 - Heavy Duty Type N-8, 9Tubular Inside Micrometers - Series 133 N-10,11Digimatic Bore Gages - Series 511 N-12,13Dial Bore Gages - Series 526 - Split-Ball Type N-14,15Dial Bore Gages - Series 511 N-16,17Dial Bore Gages with Micrometer Heads - Series 511 N-18,19Dial Bore Gages - Series 511 - For Shallow Holes N-20Holtests - Series 368 - Two Point Models N-21,22Holtests - Series 368 - Interchangeable Anvil Type N-23~25Digimatic Holtests - Series 468 - Complete Unit Sets N-26~29Dial Bore Gages - Series 545 - Rugged, Production-Line Tools N-30Borematic with Absolute Encoder - Series 568 N-31,32Setting Rings - Series 177 N-33MSG/MLS Air Gaging Models N-34Chamfer Chek - Series 526 N-35Digimatic Chamfer Chek - Series 547 N-36Hole Chek - Series 526 - Instant Dia. Meas. of Small Holes N-37

4841 W. Chicago Ave. • Chicago, IL 60651 • Ph: 773.261.2182 • Fax: 773.261.2867 • [email protected]

Precision Measuring Equipment and Industrial Supplies since 1924.www.jwdonchin.com

INSIDE MICROMETERS

N-2

Inside MicrometersSeries 345, 145

Features• Accuracy to .0002" with graduations of .001".• Easy zero adjustment.• Clear graduations on satin-chrome finish.• Caliper type jaws are made of high-grade, tool steel.

They are satin-chrome finished.• Locking clamp for positive locking of spindle.• With ratchet thimble for constant force.

• Every thousandth is numbered for easy reading.• Easily adjusted for slide movement of jaw (Exclusive.)• Spanner wrench is supplied with every micrometer.• Complete with fitted carrying case.• Digimatic type features LCD Readout, Preset,

Zero/ABS, Data/Hold, Inch/mm and SPC Output.

145-187

145-193

345-711-30

145-193300400 Holder

300401 Cap

A special holder is available for inside microme-ters.The holder must be used with No.156-101MITUTOYO Stand or any other similar stand orvise available in the shop.

SpecificationsDigimatic Inside Micrometers with Absolute EncoderInch/Metric

LCDOrder No. Range Resolution Accuracy Remarks345-711-30 .2"–1.18" .00005" ±.0002" with SPC output

5–30mm 0.001mm345-712-30 1.0"–2.0" .00005" ±.00025" with SPC output

25.4-50.8mm 0.001mm

MetricOrder No. Range Resolution Accuracy Remarks345-511-30 5–30mm 0.001mm ±0.005mm with SPC output345-512-30 25–50mm 0.001mm ±0.006mm with SPC outputNote: Metric only Digimatic models have mm thimble and no inch/mm conversion function.For SPC output order Connecting Cable 937387 (1m) or 965013 (2m). Replacement Battery: 541980 (1pc), 541980-10 (10pcs/SET).

AB

SOLUTE

TECHNOLOGY

N- 02 (2003) full size 12/8/03 7: 18 PM Page 1

Inside MicrometersInchOrder No. Range Resolution Accuracy Remarks145-193 .2"–1.18" .001" ±.0002" Measuring Face: A145-194 1.0"–2.0" .001" ±.00025" Measuring Face: B145-195 2.0"–3.0" .001" ±.0003" Measuring Face: C145-196 3.0"–4.0" .001" ±.00035" Measuring Face: C

MetricOrder No. Range Resolution Accuracy Remarks145-185 5–30mm 0.01mm ±0.005mm Measuring Face: A145-186 25–50mm 0.01mm ±0.006mm Measuring Face: B145-187 50–75mm 0.01mm ±0.007mm Measuring Face: C145-188 75–100mm 0.01mm ±0.008mm Measuring Face: C

Measuring Face: A

Measuring Face: B

Digimatic Type Range .2–1.18"(5–30mm)

Digimatic Type Range 1–2"(25–50mm)

Measuring Face: C

(.2" to 1.18")

.079"

.315".118"

.079" (Diameter)(R=.087")

Carbide Pins

1.26

"

.177

".0

79"

(1.0" to 2.0")

.48"

Carbide Inlaid(R=.48")

.177

".1

2"

.69"

.1.3

"

.118" .315"

.2"ø.079"

ø.079"

R .087"

R .087"

.18"

1.08

"

1.08

"

.49"

.17"

.37"R.47"

1.08

"

.49"

.37"

1.24"

.17"R.47"

INSIDE MICROMETERS

N-3


Inside MicrometersSeries 141 – Interchangeable Type

141-233141-101

141-102

The 141 Series Inside Micrometers are probably the mostfrequently used inside measuring instruments because oftheir wide range and simplicity in measuring operation.No. 141-233, (photo shown), consists of 5 interchangeablerods, .500" micrometer head, .500" collar 1" extensionand handle. The range covered by this unit is 2" to 12".

To provide point contact, all contact points are madespherical and hardened for extra long tool life. The overallaccuracy is .0004" up to 12" (300mm), .001" thereafter to40".

Features• Each interchangeable rod is marked with its measuring

range.• Both micrometer head and furnished rods are satin-

chrome finished throughout.• Positive locking clamp attached on No. 141-101 and

141-102. No lock on the larger sizes.• Supplied with fitted carrying case.For closer tolerance work it is recommended that themicrometer with a rod inserted be calibrated with aknown size such as a ring gage. The setting ring for“Holtest” would be an ideal choice.No. 141-102As shown here, the Micrometer Head has a 0–.250"range, reading in thousandths. A detachable holder pro-vides easy access when measuring inside diameterswithin deep holes. For 1" to 1.250" range, the micrometer

is used without the rod or collar.For 1.250" to 1.500" a .250" collar is added between therod and head. For 1.500" to 1.750" range, the rod isreplaced. For 1.750" to 2", the collar is added betweenthe rod and head. Thus, it measures 1" to 2"–.250" at atime.No. 141-233Since this Inside Micrometer comes with a .500" rangeMicrometer Head, the combining of rod, collar andextended thimble is made simpler. For instance: the rodmarked 4–6" measures from 4"–4.5". For 4.5–5" range,the .500 collar is added. For 5"–5.5" the extension thim-ble is used and for 5.5" to 6" the extension thimble andcollar are used.Both measuring ends are hardened and have micro-lapped finish for lasting accuracy.

INSIDE MICROMETERS

N-4


1.71" (43.5)

.07"(1.8)

.05"(1.2)

.24"(6.2)

(METRIC)

ø.16" (ø4) hole

ø.47

"(ø

12)

ø.59

"(ø

15)

ø.2"

(ø15

)

.35"

(8.8

).4

5"(1

1.5)

SR .39"(SR10)

ø.26

"(ø

6.5)

.54"(13.7)

.91"(23)

.2"(5)

SpecificationsInside Micrometers—Interchangeable Rod TypeInch

Spacing DiameterOrder No. Range Collar of Rods Remarks141-102 1–2" .250" .248" Includes 141-002 and 2 pcs rods141-208 2–8" .500" .248" Includes 141-026, 3 rods and 1" extended thimble141-233 2–12" .500" .248" Includes 141-026, 5 rods and 1" extended thimble141-121 8–20" 1", 2" .355" Includes 141-010 and 3 pcs rods141-122 8–40" 1", 2" .355" Includes 141-010 and 8 pcs rods

MetricSpacing Diameter

Order No. Range Collar of Rods Remarks141-101 25–50mm 6.0mm 6.3mm Includes 141-001 and 2 pcs rods141-205 50–200mm 12.0mm 6.3mm Includes 141-025, 3 rods and 25mm extended thimble141-206 50–300mm 12.0mm 6.3mm Includes 141-025, 5 rods and 25mm extended thimble141-117 200–500mm 25mm, 50mm 9.0mm Includes 141-009 and 3 pcs rods141-118 200–1000mm 25mm, 50mm 9.0mm Includes 141-009 and 8 pcs rods

Micrometer HeadsInchOrder No. Head Travel Resolution Accuracy141-002 .25" .001" ±.0001"141-026 .50" .001" ±.0001"141-010 1.00" .001" ±.0001"

MetricOrder No. Head Travel Resolution Accuracy141-001 7.0mm 0.01mm ±0.003mm141-025 13.0mm 0.01mm ±0.003mm141-009 25.0mm 0.01mm ±0.003mm

141-001

141-026

INSIDE MICROMETERS

N-5


Tubular Inside MicrometersSeries 337, 137 – Extension Type

Features• Wide range of ID measurements by combining

extension rods with the micrometer head. The rod is accurately finished and incorporated in a pipe forshop-floor use.

• The 337 series provides digital readout to.0001"/0.001mm and can be linked to the SPC System.

• Digimatic Function Include:PresetInch/mm conversionZero-Set/ABSHold Data Output

• Power Supply:One Silver oxide cell (SR-44), offers 4,500 hours of life

• The display automatically turns off if idle after 20 minutes.

Accuracy• Series 137, 337:[±(.00015+.00005n+.00005 (L/2))"]*/±(3+n+L/50)µm *n=Number of rods, L=Maximum measuring length [(inch)] (mm),Fraction rounded up

337-203

137-102

SpecificationsDigimatic Inside MicrometersInch/Metric

LCD Head Extension RodsOrder No. Range Resolution Travel (Dia .50") Remarks337-203 8–40" .0001"/0.001mm 1.0" 1", 2", 4" (2 pcs.) Includes Micrometer

8", 12" Head with SPC output.

337-204 8–60" .0001"/0.001mm 1.0" 1", 2", 4", 8" Includes Micrometer12" (3 pcs.) Head with SPC output

For SPC output order Connecting Cable 937387 (1m) or 965013 (2m).Replacement Battery: 541980 (1 pc.), 541980-10 (10 pcs. SET)

INSIDE MICROMETERS

N-6


Included in Set Nos. 337-203 and 337-204.

137-002

Inside MicrometersInch

Extension RodsOrder No. Range (Diameter .50") Remarks137-112 2–12" .5", 1", 2"(2pcs), 4" Include 137-002 137-114 2–40" .5", 1", 2", 4"(2pcs), 6", 8", 12" Include 137-002

MetricExtension Rods

Order No. Range (Diameter 12.5mm) Remarks137-102 50–300mm 13, 25, 50(2pcs), 100mm Include 137-001 137-104 50–1000mm 13, 25, 50, 100(2pcs), 150, 200, 300mm Include 137-001 137-108 50–500mm 13, 25, 50(2pcs), 100, 200mm Include 137-001

Rods with Carbide-tipped Measuring Face

Micrometer HeadsInchOrder No. Head Travel Resolution Accuracy137-002 .50" .001" ±.0001"

MetricOrder No. Head Travel Resolution Accuracy137-001 13.0mm 0.01mm ±0.003mm

INSIDE MICROMETERS

N-7


Tubular Inside MicrometersSeries 339, 139, 140 – Heavy Duty Type

Features• Wide range of ID measurements by combining exten-

sion pipes and anvils with the micrometer head.• The 339 series provides digital readout to

.0001"/0.001mm and can be linked to the SPC System.• Pipe diameter

139 series: .67"/17mm140 series: 1.26"/32mm

• For higher repeatability of measurement, light weightextension pipes made of CFRP (Carbon FiberReinforced Plastic) for 139 Series.

• Digimatic Functions Include:PresetInch/mm conversionZero set/ABSHoldData output

• Power Supply: One silver oxide cell (SR-44) offers 4,500 hours of life

• The display automatically turns off idle after 20 minutes

Accuracy• Series 139, 339:[±(.00015+.00005n+.00005 (L/2))"]/±(3+n+L/50)µm*• Series 140:[±.(0003+.00005n+.00005 (L/2))"]/±(7+n+L/50)µm**n=Number of rods, L=Maximum measuring length [(inch)] (mm),Fraction rounded up

339-293 139-179

SpecificationsTubular Inside MicrometersInch

Diameter ExtensionOrder No. Range of Rods Rods Remarks139-201 1.5–12" .375" .5", 1", 2", 2.5", 3", 3.5", 4", 6" Include 139-004139-202 4–40" .375" 1", 2", 3", 6", 9", 12", 14", 16", 17", 18" Include 139-006

SpecificationsDigimatic Inside Micrometers (Series 339)Inch/Metric

LCD Head DiameterOrder No. Range Resolution Travel of Rods Remarks339-293 8–40" .0001" 1.0" .67" Include Micrometer Head and 5 pcs rods

0.001mm with SPC output339-294 8–80" .0001" 1.0" .67" Include Micrometer Head and 8 pcs rods

0.001mm with SPC outputFor SPC output order Connecting Cable 937387 (1m) or 965013 (2m).Replacement Battery: 541980 (1 pc.), 541980-10 (10 pcs./SET)

INSIDE MICROMETERS

N-8


139-002 139-004

139-006 Included in Set Nos. 339-293and 339-294.

1.7 8 11 1.5 23 4.8 4.5 2.5 15 25

Ø33Ø33

175.5

Ø8

16.5

Ø21

Ø32

Ø19

Ø8

15101699

1000 to 1050

Micrometer Head for series 140

3 47

Ø4

Ø18

139-001137-001

3

SR10

SR10

100 to 125

3

SR10 SR10SR10

SR10

Ø4

Ø15

Ø4

Ø4

M10x1

50

1

Inside Micrometer HeadsInchOrder No. Head Travel Resolution Accuracy139-002 1.0" .001" ±.00015"139-004 .50" .001" ±.00015"139-006 1.0" .001" ±.00015"

MetricOrder No. Head Travel Resolution Accuracy139-001 25.0mm 0.01mm ±0.003mm

Inside Micrometers (Series 139)Inch

Extension RodsOrder No. Range (Diameter .67") Remarks139-178 4–20" 1", 2", 4", 8" Include 139-002 139-179 4–36" 1", 2", 4", 8", 16" Include 139-002 139-180 4–52" 1", 2", 4", 8", 16"(2pcs.) Include 139-002

Inside Micrometers (Series 140)Inch

Head Extension RodsOrder No. Range Resolution Travel (Diameter 1.26") Remarks140-162 40-120" .001" 2.0" 2", 4"(2pcs.), 8", 20", 40" Include Micrometer Head 140-163 40-160" .001" 2.0" 2", 4"(2pcs.), 8", 20", 40"(2pcs.) Include Micrometer Head 140-164 40-200" .001" 2.0" 2", 4"(2pcs.), 8", 20", 40"(3pcs.) Include Micrometer Head

INSIDE MICROMETERS

N-9


Tubular Inside MicrometersSeries 133

Features• Accuracy up to 4" ±.00015"

4–6" ±.0002"6–12" ±.0003"

• With positive locking clamp.• Zero point can be readjusted by twisting the micrometer

head sleeve. A key wrench is supplied.

• 2–6" set and 2–12" set are available.• Clear, crisp graduations on the satin chrome finished

micrometer head.• Carbide tipped measuring faces.• Supplied in a carrying case.

Tubular Inside MicrometersMetricOrder No. Range Resolution Accuracy133-143 50-75mm 0.01mm ±3 µm133-144 75-100mm 0.01mm ±4 µm133-145 100-125mm 0.01mm ±5 µm133-146 125-150mm 0.01mm ±5 µm133-147 150-175mm 0.01mm ±5 µm133-148 175-200mm 0.01mm ±5 µm133-149 200-225mm 0.01mm ±5 µm133-150 225-250mm 0.01mm ±6 µm133-151 250-275mm 0.01mm ±6 µm133-152 275-300mm 0.01mm ±6 µm

Tubular Inside Micrometer SetsMetricOrder No. Total Range Set Configuration133-901 50-150mm 133-143, 144, 145, 146

(4 Mikes/set) with fitted case133-902 50-300mm 133-143, 144, 145, 146,

(10 Mikes/set) 147, 148, 149, 150, 151, 152with fitted case

SpecificationsTubular Inside MicrometersInchOrder No. Range Resolution Accuracy133-223 2–3" .001" ±.00015"133-224 3–4" .001" ±.0002"133-225 4–5" .001" ±.00025"133-226 5–6" .001" ±.00025"133-227 6–7" .001" ±.00025"133-228 7–8" .001" ±.00025"133-229 8–9" .001" ±.00025"133-230 9–10" .001" ±.0003"133-231 10–11" .001" ±.0003"133-232 11–12" .001" ±.0003"

Tubular Inside Micrometer SetsInchOrder No. Total Range Set Configuration133-903 2–6" 133-223, 224, 225, 226

(4 Mikes/set) with fitted case133-904 2–12" 133-223, 224, 225, 226,

(10 Mikes/set) 227, 228, 229, 230, 231, 232with fitted case

133-223 133-224

133-225

133-226

INSIDE MICROMETERS

N-10


Tubular Inside Micrometers Series 133

DIMENSIONS (metric)Order No. L A B133-145 100 3.8 3133-146 125 3.5 3133-147 150 16.5 15133-148 175 15.5 15133-149 200 15.5 15133-150 225 15.5 15133-151 250 15.5 15133-152 275 15.5 15

B

R=.394"(SR10)

R=.394"(SR10)

ø.3

15"

(ø8)

ø.3

15"

(ø8)

A 1.85"(47)

.71"

(ø

18)

L

R=.394"(SR10)

R=.394"(SR10)

133-143133-223

ø.3

15"

(ø8)

ø.3

15"

(ø8)

ø.5

9"

.14"(3.5)

.12"(3)

1.45"(37)

1.97"(50)

.14"(3.5)

R=.394"(SR10)

133-144133-224

R=.394"(SR10)

1.45"(37)

2.95"(75)

ø.5

9"

ø.3

15"

(ø8)

ø.3

15"

(ø8)

(mm)

DIMENSIONS (inch)Order No. L A B133-225 4" .15" .12"133-226 5" .14" .12"133-227 6" .65" .59"133-228 7" .61" .59"133-229 8" .61" .59"133-230 9" .61" .59"133-231 10" .61" .59"133-232 11" .61" .59"

INSIDE MICROMETERS

N-11


Digimatic Bore GagesSeries 511

Features• .00012” (0.003mm) or less wide range accuracy

• Anvil displacement is directly detected by the ultra compac built-in sensor (no mechanical transmitter is used)

• Maximum extension up to 78.74” (2000mm)

• Reaches deep holes easily!

• Simple to operate – can preset 3 reference (master) valueand set upper/lower tolerance limits for each!

• IP53 dust/water protection level

Specifications Order No. 511-521Range 1.8" - 4" (45 - 100mm)Contact Point Stroke .048" / 1.2mmResolution .00005" / 0.001mmWide range accuracy .00012" / 0.003mmNarrow range accuracy .00008" / 0.002mmRepeatability ±1 countQuantizing error ±1 countMeasuring force 5N or lessBattery (541980) Silver oxide cell (SR-44–2 pcs.)Battery Life 9 months under normal useSensor/scale Electrostatic capacitance

absolute scaleSampling frequency 50 times / secProtection level IP53Data output SPC data outputMass 1.1 lbs. / 500g

Standard AccessoriesAnvils 14 pcs.Spacer 4 pcs. .02", .04", .08", .12"Hex Wrench 1 pc.Optional Accessories905338 SPC Cable 40"/1m905409 SPC Cable 80"/2m21DZA089 Extension Rod 9.84"/250mm21DZA081 Extension Rod 19.69"/500mm516-120-22 Measuring Size set

Gage Block Set

Specifications Order No. 516-120-22Set of:Steel Rectangular gage Block.04", .08", .16", .2", .4", .8", 1", 2", 3"Flat Jaw (619970) 2 pcs.Holder 160mm (619004) 1 pc.Wooden Box

N-12

BORE GAGES

N- 12 (2003) full size 12/9/03 9: 52 AM Page 1

Digimatic Bore GagesSeries 511

inclination (90°)

29.4RESET sw

100

3.93

7"

150

5.90

6"15

05.

906"

301.181"

281.102"

341.339"

28

( ):for 19.685"/500mm type

ø1.102"

20.7

87"

16.5

M26x1.5

ø28

ø1.102"

.65"

1.5

.059

"26

8.5

(518

.5)

232

(482

)

10.5

71"

(20.

413"

)

9.13

4" (

18.9

76")

250

(500

)

ø22ø.866"

ø 30ø 1.181"

9.3

54"

SR 2

R.079"

SR 2

R.079"

(339

.5)

(13.

366"

)

For inch-readable model

ON/OFF in/mm sw

TOL sw

M/W sw

DATA/HOLD sw

PRESET sw

START sw

ø61ø2.402"

rotation(320°)

rotation(320°)

1.157"

9.84

3" (

19

.685

")

Dimensions

BORE GAGES

N-13


Dial Bore GagesSeries 526 – Split-Ball Type

Features• Measures diameters of small holes.• Radius displacement of split-ball contact is converted to

axial displacement of measuring pin, which is shown onthe dial indicator.

• Digimatic Indicator can be installed in place of the dialindicator.

• Accuracy: .00016"/4µm (Range: .037–.4"/0.95–10mm).00024"/6µm (Range: .4–.7"/10–18mm)

• Optional stand (215-120) for Bore Gages Series 526 is available for efficient measurement of multiple small holes.

Optional Stand(215-120M)526-120

526-173P

robe

Dep

th (

L)

SpecificationsDial Bore GagesInchOrder No.* Order No. Order No. Measuring Number of ProbeWithout Dial With 2922FB With 2923FB-10 Range Anvils DepthGage Graduation .0005" Graduation .0001"

526-103 526-119 526-122 .3"-.4" 6 pcs. 2.2"526-104 526-120 526-123 .4"-.7" 8 pcs. 2.4"*Does not include dial gage cover.

MetricOrder No.* Order No. Order No. Measuring Number of ProbeWithout Dial With 2046FB With 2109FB Range Anvils DepthGage Graduation 0.01mm Graduation .0.001mm

526-101 526-126 526-124 7-10mm 6 pcs. 56mm526-102 526-127 526-125 10-18mm 8 pcs. 62mm*Does not include dial gage cover.

N-14

BORE GAGES


SpecificationsDial Bore GagesSplit-Ball TypeInchOrder No.* Order No. with Measuring Anvil Setting Ring No. ofWithout 2923FB-10 Range Probe Range Length Code No. Size NeedleDial Gage Graduation .0001" No.

1.0 .037"–.045" 177-220 .04"1.1 .042"–.049" 177-222 .045"

526-175 526-176 .037"–.061" 1.2 .046"–.053" .45" 177-225 .05" 11.3 .050"–.057" 177-227 .055"1.4 .054"–.061" 177-230 .06"1.75 .060"–.075" 177-236 .07"2.00 .070"–.085" .69" 177-239 .08"2.25 .080"–.095" 177-242 .09"2.50 .090"–.105" 177-208 .10"

526-165 526-166 .060"–.157" 2.75 .100"–.115" 177-246 .11" 23.00 .110"–.125"

.89"177-248 .12"

3.25 .120"–.135" 177-250 .13"3.50 .130"–.145" 177-252 .14"3.75 .140"–.157" 177-255 .15"4.0 .145"–.170" 177-204 .16"4.5 .165"–.190" 177-257 .18"5.0 .185"–.210" 177-205 .20"

526-155 526-156 .145"–.290" 5.5 .205"–.230" 1.26" 177-263 .22" 16.0 .225"–.250" 177-267 .24"6.5 .245"–.270" 177-271 .26"7.0 .265"–.290" 177-275 .28"

MetricOrder No.* Order No. with Order No. with Measuring Anvil Setting Ring No. ofWithout 2046FB 2109FB Range Probe Range Length Code Size NeedleDial Gage Graduation Graduation No. (mm) No. (mm)

0.01mm 0.001mm1.0 0.95–1.15mm 177-220 1.01.1 1.07–1.25mm 177-222 1.1

526-170 526-173 526-172 0.95–1.55mm 1.2 1.17–1.35mm 11.5 177-225 1.2 11.3 1.27–1.45mm 177-227 1.31.4 1.37–1.55mm 177-230 1.41.75 1.50–1.90mm 177-236 1.752.00 1.80–2.20mm 17.5 177-239 2.002.25 2.05–2.45mm 177-242 2.252.50 2.25–2.75mm 177-208 2.50

526-160 526-163 526-162 1.5–4mm 2.75 2.50–3.00mm 177-246 2.75 23.00 2.75–3.25mm 22.5 177-248 3.003.25 3.00–3.50mm 177-250 3.253.50 3.25–3.75mm 177-252 3.503.75 3.50–4.00mm 177-255 3.754.0 3.7–4.3mm 177-204 4.04.5 4.2–4.8mm 177-257 4.55.0 4.7–5.3mm 177-205 5.0

526-150 526-153 526-152 3.7–7.3mm 5.5 5.2–5.8mm 32 177-263 5.5 16.0 5.7–6.3mm 177-267 6.06.5 6.2–6.8mm 177-271 6.57.0 6.7–7.3mm 177-275 7.0

Above sets include setting rings.*Does not include Dial gage cover.

N-15

BORE GAGES


055

1010

1515

202025

S H O C K P R O O F

MADE IN JAPAN

NO. 2922-08 ®

.0005"

01

2 3

+ _

®

.0001"

6 J E W E L S

011

22

33

445

_+

Shock

0 .01"

010

20

30

4050

60

70

80

900 11 22

33445566

7788 99 10

_ +

NO.1011-11

1µm

J E W E L E D 0 98

7654

3

21

2 34

501 .6 .4

.2

010.8

0 10102020

3030

4040

5050

6060

70708080

9090 100

1µm

0. 2

. 4 . 6. 81.0

M A D E I N J A P A N

6 J E W E L S

NO. 2109FB ®

Dial Bore GagesSeries 511

511-212

511-162

Features• Interchangable anvils and necessary accessories to

perform close tolerance I.D. measurements.• Carbide ball contact point for durability.

• Optional extension rods can be attached.• A Digimatic Indicator can be attached in place of the

dial gage.• Accuracy: .0002"/5µm

Type of Measuring Head

2922FB.0005"

.24–.4"

2923FB-10.0001"

2109FB0.001mm

2046FB0.01mm

.4"–.74"10–18.5mm

.7"–2.4"18–60mm

2.0"–16.0"50–400mm

Dial Faces

N-16

BORE GAGES


SpecificationsDial Bore Gages InchOrder No.* Order No. Order No. Measuring Number Number ProbeWithout With 2922FB With 2923FB-10 Range of Anvils of Spacers DepthDial Gage Graduation .0005" Graduation .0001"511-214 511-213 511-212 .24"-.4" 9 pcs. - 2"511-205 511-207 511-206 .4"-.74" 9 pcs. 1 4"511-104 511-159 511-163 .7"-1.4" 8 pcs. 3 4"511-105 511-160 511-164 1.4"-2.5" 6 pcs. 4 6"511-107 511-162 511-166 2"-6" 11 pcs. 4 6"

2" Sub-Anvil511-181 511-184 511-187 4"-6.5" 13 pcs. 4 6"511-182 511-185 511-188 6.5"-10.0" 6 pcs. 6 10"511-183 511-186 511-189 10.0"-16.0" 5 pcs. 6 10"

511-911 (set) 511-912 (set) .7"-6.0" 25 pcs. 7 4", 6"2" Sub-anvil

*Does not include dial gage cover.

MetricOrder No.* Order No. Order No. Measuring Number Number ProbeWithout With 2046FB With 2109FB Range of Anvils of Spacers DepthDial Gage Graduation 0.01mm Graduation 0.001mm511-201 511-204 511-203 10-18.5mm 9 pcs. 1 90mm511-126 511-171 511-167 18-35mm 9 pcs. 2 100mm511-127 511-172 511-168 35-60mm 6 pcs. 4 150mm511-128 511-173 511-169 50-100mm 11 pcs. 4 150mm511-132 511-174 511-170 50-150mm 11 pcs. 4 150mm

50 mm Sub-anvil511-129 511-175 511-178 100-160mm 13 pcs. 4 150mm511-130 511-176 511-179 160-250mm 6 pcs. 7 250mm511-131 511-177 511-180 250-400mm 5 pcs. 7 250mm

511-901 (set) 511-902 (set) 18-150mm 26 pcs. 7 100mm50mm Sub-anvil 150mm

*Does not include dial gage cover.

Optional AccessoriesExtension RodsBore Gage Extension LengthMeasuring 4.92" 9.84" 19.69" 29.53" 39.37" Rod SpannerRange 125mm 250mm 500mm 750mm 1000mm Diameter.7–1.4" 953549 953550 953551 –– –– .34" 102148A18–35mm 8.7mm1.4–6.5" 953552 953553 953554 953555 953556 .47" 21255635–160mm 12mm6.5–16" 953557 952361 953558 953559 953560 .59" 212556160–400mm 15mmNote: Above list is used for 511-1XX series; not available for 511-2XX Series.

N-17

BORE GAGES


Dial Bore Gages with Micrometer HeadsSeries 511

Features• Interchangeable anvil is attached to a micrometer head

for accurate dimensional setting.• Carbide ball contact point for durability.• Measuring range can be expanded by attaching a

sub-anvil.

• Optional extension rods can be attached.• A Digimatic Indicator can be attached in place of the


511-319

Ring gages offer the bestmethod of zero setting DialBore Gages.

Pro

be D

epth

Extension Rod

N-18

BORE GAGES


Optional AccessoriesExtension RodsBore Gage Extension LengthMeasuring 4.92" 9.84" 19.69" 29.53" 39.37" Rod SpannerRange 125mm 250mm 500mm 750mm 1000mm Diameter1.4-2.5" 953549 953550 953551 –– –– .34" 102148A35–60mm 8.7mm2.4–6.4" 953552 953553 953554 953555 953556 .47" 21255660–160mm 12mm6.0–32.0" 953557 952361 953558 953559 953560 .59" 212556150–800mm 15mmNote: Above list is used for 511-3XX Series.

SpecificationsDial Bore Gages with Micrometer Heads InchOrder No.* Order No. Order No. Measuring Mike Head Extensions ProbeWithout With 2922FB With 2923FB-10 Range Travel Mike Head DepthDial Gage Graduation .0005" Graduation .0001"511-342 511-345 511-346 1.4-2.5" .2" .2", .4", .6", .8" 6"511-332 511-335 511-336 2.4-4.0" .4" .4", .8" 6"511-306 511-325 511-326 4.0-6.0" .5" .4", .8", .8" 6"511-307 511-319 511-320 6.0-10.0" 1" 1", 2" 10"511-308 511-321 511-322 10.0-16.0" 2" 2", 2" 10"511-309 511-323 511-324 16.0-24.0" 2" 2", 4" 10"511-310 511-329 511-330 24.0-32.0" 2" 2", 4" 10"*Does not include dial gage cover.

MetricOrder No.* Order No. Order No. Measuring Mike Head Extensions ProbeWithout With 2046FB With 2109FB Range Travel Mike Head DepthDial Gage Graduation 0.01mm Graduation 0.001mm511-341 511-344 511-343 35-60mm 5mm 5mm, 10mm

15mm, 20mm 150mm511-331 511-334 511-333 60-100mm 10mm 10mm, 20mm 150mm511-301 511-312 511-311 100-160mm 13mm 10mm, 20mm,

20mm 150mm511-302 511-314 511-313 150-250mm 25mm 25mm, 50mm 250mm511-303 511-316 511-315 250-400m 50mm 50mm, 50mm 250mm511-304 511-318 511-317 400-600mm 50mm 50mm, 100mm 250mm511-305 511-328 511-327 600-800mm 50mm 50mm, 100mm 250mm*Does not include dial gage cover.

N-19

BORE GAGES


SpecificationsDial Bore GagesInchOrder No.* Order No. Order No. Measuring Number of Number ofWithout Dial With 2922FB With 2923FB-10 Range Anvils SpacersGage Graduation .0005" Graduation .0001"

511-406 511-431 511-441 .6-1.4" 11 pcs., .4" Sub-anvil 1511-407 511-432 511-442 1.4-2.4" 6 pcs. 4511-408 511-433 511-443 2.0-4.0" 11 pcs. 4511-409 511-434 511-444 2.0-6.0" 11 pcs., 2" Sub-anvil 4*Does not include dial gage cover.

MetricOrder No.* Order No. Order No. Measuring Number of Number ofWithout Dial With 2046FB With 2109FB Range Anvils SpacersGage Graduation 0.01mm Graduation 0.001mm

511-401 511-411 511-421 15-35mm 11 pcs., 10mm Sub-anvil 1511-402 511-412 511-422 35-60mm 6 pcs. 4511-403 511-413 511-423 50-100mm 11 pcs. 4511-404 511-414 511-424 50-150mm 11 pcs., 50mm Sub-anvil 4*Does not include dial gage cover.Extension rods are not available for 511-4XX Series.

Dial Bore GagesSeries 511

For Shallow Holes

Features• Can measure ID at position close to the bottom of

blind holes.• A Digimatic Indicator can be attached in place of the


511-431 511-442

Pro

be D

epth

6" (

150m

m)

N-20

BORE GAGES


HoltestsSeries 368 – Two Point Models for Very Small Holes

SpecificationsHoltests–Two Point ModelsInch

Individual AccessoriesSet Order No. Range Order No. Grad. L1 L2 Included In Set

368-926 .080–.100" 368-021 .0001" .47" 4" 177-209 Setting Ring .100" Dia..100–.120" 368-022 .0001" .47" 4" 202863 Hex Wrench.120–.160" 368-023 .0001" .86" 4.5" 177-206 Setting Ring .160" Dia.

368-927 .160–.200" 368-024 .0001" .86" 4.5" 177-207 Setting Ring .240" Dia..200–.240" 368-025 .0001" .86" 4.5" 202863 Hex Wrench.240–.280" 368-026 .0001" .86" 4.5"

MetricIndividual Accessories

Set Order No. Range Order No. Grad. L1 L2 Included in Set

368-906 2–2.5mm 368-001 0.001mm 12mm 104mm 177-208 Setting Ring 2.5mm Dia.2.5–3mm 368-002 0.001mm 12mm 104mm 202863 Hex Wrench3–4mm 368-003 0.001mm 22mm 114mm 177-204 Setting Ring 4mm Dia.

368-907 4–5mm 368-004 0.001mm 22mm 114mm 177-205 Setting Ring 5mm Dia.5–6mm 368-005 0.001mm 22mm 114mm 202863 Hex Wrench

To read ID’s to .0001" directly, the probe movement isdesigned to assure consistent accuracy over the entirerange. The probe movement fixes one side of the probeand allows the other half of the probe to move parallelto the stationary side. With this new design and the leaf-spring mechanism, these Holtests are, by far, the mostdirect and accurate instruments to check small holediameters.

368-022

368-023

368-024

368-025

AccuracyInch Type .00008"Metric Type 0.002mm

Measuring Force (per Anvil)4–20N

HOLTESTS

N-21


Holtests Series 368

SpecificationsHoltest

Inch with CarbideSet Individual AccessoriesOrder No. Range Order No. Graduation L1 L2 included in Set

.275–.350" 368-201 .0001" 2.32" 4.05"~4.13"177-179 Setting Ring .350" DIA.

368-921 .350–.425" 368-202 .0001" 2.32" 4.05"~4.13"177-180 Setting Ring .500" DIA.

.425–.500" 368-203 .0001" 2.32" 4.05"~4.13"952322 Extension Rod 4"205289 Spanners (pair)202863 Hex Wrench

Metric with CarbideSet Individual AccessoriesOrder No. Range Order No. Graduation L1 L2 included in Set

6–8mm 368-101 0.001mm 59mm 103~105mm177-125 Setting Ring 8mm DIA.

368-901 8–10mm 368-102 0.001mm 59mm 103~105mm177-126 Setting Ring 10mm DIA.

10–12mm 368-103 0.001mm 59mm 103~105mm952322 Extension Rod 100mm205289 Spanners (pair)202863 Hex Wrench

These Holtests are versatile, three-pointinternal micrometers for the accurate andefficient direct-measurement of internaldiameters. Three anvils, evenly spaced at 120° apart, contact the internal wall sur-faces and find true alignment with the axisof the bore for accurate ID measurement.

Features• Measurement can be taken nearly up to

the bottom of the bore.• Highly durable because of carbide tipped

contact points.• Can measure deep holes using an exten-

sion rod which is available on modelsover 6mm measuring range.

• Ratchet stop for constant measuringforce.

368-201

368-103

Extension Rods (optional)Application range

Inch Metric Order No. Length.275–.5" 6–12mm 952322 3.94"(100mm)

.5–.8" 12–20mm 952621 5.9" (150mm).8–1.2" 20–30mm 952622 5.9" (150mm)

1.2–4.4" 30–110mm 952623 5.9" (150mm)

AccuracyRange Accuracy.275–.8" .00008"6–20mm 0.002mm.8–4" .00012"20–100mm 0.003mm4–12" .0002"100–300mm 0.005mm

Measuring Force (per Anvil)Range.275–.5"

4–20N6–12mm.5–4"

15–45N12–100mm4–12"

30–75N100–300mm

HOLTESTS

N-22


HoltestsSeries 368 – Interchangeable Anvil Type

Internal Construction

368-206

368-238

HoltestStandard Finish

Holtestwith Carbide

a=.012" 0.3mmRange .5-1.2" 12-30mm

SpecificationsInchSet IndividualOrder No. Range Order No. Graduation L1 L2 Accessories included in Set

Hardened Alloy Tool Steel Anvil and Cone (Standard Finish)368-982 .500–.650" 368-804 .0002" 3.15" 4.88~5.04"

.650–.800" 368-805 .0002" 3.15" 4.88~5.04"

With Carbide368-922 .500–.650" 368-204 .0002" 3.15" 4.88~5.04"

.650–.800" 368-205 .0002" 3.15" 4.88~5.04"

Hardened Alloy Tool Steel Anvil and Cone (Standard Finish).800–1.000" 368-806 .0002" 3.54" 5.31~5.51"

368-968 1.000–1.200" 368-807 .0002" 3.54" 5.31~5.51"1.200–1.600" 368-838 .0002" 3.86" 5.67~6.06"1.600–2.000" 368-839 .0002" 3.86" 5.67~6.06"

With Carbide.800–1.000" 368-206 .0002" 3.54" 5.31~5.51"

368-958 1.000–1.200" 368-207 .0002" 3.54" 5.31~5.51"1.200–1.600" 368-238 .0002" 3.86" 5.67~6.06"1.600–2.000" 368-239 .0002" 3.86" 5.67~6.06"

177-182 Setting Ring, .650" DIA.

952621 Extension Rod, 5.9"

205312 Spanners (Pair)

202863 Hex Wrench

177-184 Setting Ring, 1.000" DIA.

177-291 Setting Ring, 1.600" DIA.

952622 Extension Rod, 5.9"

210189 Spanner (Pair)

202863 Hex Wrench

2416

1

HOLTESTS

N-23


Holtests Series 368

SpecificationsInchSet Individual AccessoriesOrder No. Range Order No. Graduation L1 L2 included in Set

Hardened Alloy Tool Anvil and Cone (Standard Finish)2.0–2.5" 368-840 .0002" 4.13" 5.94~6.46"

368-969 2.5–3.0" 368-841 .0002" 4.13" 5.94~6.46"3.0–3.5" 368-842 .0002" 4.13" 5.94~6.46"3.5–4.0" 368-843 .0002" 4.13" 5.94~6.46"With Carbide2.0–2.5" 368-240 .0002" 4.13" 5.94~6.46"

368-959 2.5–3.0" 368-241 .0002" 4.13" 5.94~6.46"3.0–3.5" 368-242 .0002" 4.13" 5.94~6.46"3.5–4.0" 368-243 .0002" 4.13" 5.94~6.46"Hardened Alloy Tool Steel Anvil and Cone (Standard Finish)4–5" 368-817 .0002" 6.22" 8.78~9.76"

368-985 5–6" 368-818 .0002" 6.22" 8.78~9.76"6–7" 368-819 .0002" 6.22" 8.78~9.76"7–8" 368-820 .0002" 6.22" 8.78~9.76"With Carbide4–5" 368-217 .0002" 6.22" 8.78~9.76"

368-925 5–6" 368-218 .0002" 6.22" 8.78~9.76"6–7" 368-219 .0002" 6.22" 8.78~9.76"7–8" 368-220 .0002" 6.22" 8.78~9.76"Hardened Alloy Tool Steel Anvil and Cone (Standard Finish)8–9" 368-821 .0002" 6.22" 8.78~9.76"9–10" 368-822 .0002" 6.22" 8.78~9.76"10–11" 368-823 .0002" 6.22" 8.78~9.76"11–12" 368-824 .0002" 6.22" 8.78~9.76" Larger Holtests are soldWith Carbide individually. No set available.8–9" 368-221 .0002" 6.22" 8.78~9.76"9–10" 368-222 .0002" 6.22" 8.78~9.76"10–11" 368-223 .0002" 6.22" 8.78~9.76"11–12" 368-224 .0002" 6.22" 8.78~9.76"

NOTE: “Holtest” Sets are not available over 8" Range.

177-315 Setting Ring, 2.5" DIA.177-319 Setting Ring, 3.5" DIA.952623 Extension Rod, 5.9"210189 Spanners (Pair)202863 Hex. Wrench

177-299 Setting Ring, 5" Dia.177-303 Setting Ring, 7" Dia.952623 Extension Rod, 5.9"205348 Spanners (Pair)202863 Hex. Wrench

a= .012" 0.3mmRange .5-4" 12-100mm

a= .134" 3.4mmRange .5-4" 12-100mm

a= .512" 13mmRange 4-12" 100-300mm

a= .772" 19.6mmRange 4-12" 100-300mm

HOLTESTS

N-24


HoltestsSeries 368

SpecificationsMetricSet IndividualOrder No. Range Order No. Graduation L1 L2 Accessories included in Set

Hardened Alloy Tool Steel Anvil and Cone (Standard Finish)368-972 12–16mm 368-704 0.005mm 80mm 124~128mm

16–20mm 368-705 0.005mm 80mm 124~128mmWith Carbide

368-902 12–16mm 368-104 0.005mm 80mm 124~128mm16–20mm 368-105 0.005mm 80mm 124~128mmHardened Alloy Tool Steel Anvil and Cone (Standard Finish)20–25mm 368-706 0.005mm 90mm 135~140mm

368-963 25–30mm 368-707 0.005mm 90mm 135~140mm30–40mm 368-738 0.005mm 98mm 144~154mm40–50mm 368-739 0.005mm 98mm 144~154mmWith Carbide20–25mm 368-106 0.005mm 90mm 135~140mm

368-953 25–30mm 368-107 0.005mm 90mm 135~140mm30–40mm 368-138 0.005mm 98mm 144~154mm40–50mm 368-139 0.005mm 98mm 144~154mmHardened Alloy Tool Steel Anvil and Cone (Standard Finish)50–63mm 368-740 0.005mm 105mm 151~164mm


368-954 62–75mm 368-141 0.005mm 105mm 151~164mm75–88mm 368-142 0.005mm 105mm 151~164mm87–100mm 368-143 0.005mm 105mm 151~164mmHardened Alloy Tool Steel Anvil and Cone (Standard Finish)100–125mm 368-717 0.005mm 158mm 223~248mm


368-905 125–150mm 368-118 0.005mm 158mm 223~248mm150–175mm 368-119 0.005mm 158mm 223~248mm175–200mm 368-120 0.005mm 158mm 223~248mmHardened Alloy Tool Steel Anvil and Cone (Standard Finish)200–225mm 368-721 0.005mm 158mm 223~248mm225–250mm 368-722 0.005mm 158mm 223~248mm250–275mm 368-723 0.005mm 158mm 223~248mm275–300mm 368-724 0.005mm 158mm 223~248mmWith Carbide200–225mm 368-121 0.005mm 158mm 223~248mm225–250mm 368-122 0.005mm 158mm 223~248mm250–275mm 368-123 0.005mm 158mm 223~248mm275–300mm 368-124 0.005mm 158mm 223~248mm

NOTE: “Holtest” Sets are not available over 200mm Range.

177-177 Setting Ring, 16mm DIA.952621 Extension Rod, 150mm205312 Spanners (Pair)202863 Hex. Wrench

177-139 Setting Ring,25mm DIA.177-140 Setting Ring, 40mm DIA.952622 Extension Rod, 150mm210189 Spanners (Pair)202863 Hex. Wrench

177-314 Setting Ring, 62mm DIA.177-318 Setting Ring, 87mm DIA.952623 Extension Rod, 150mm210189 Spanners (Pair)202863 Hex. Wrench

177-298 Setting Ring, 125mm Dia.177-302 Setting Ring, 175mm Dia.952623 Extension Rod, 150mm205348 Spanners (Pair)202863 Hex. Wrench

Larger Holtests are sold individually.No set available.

HOLTESTS

N-25


Digimatic HoltestsSeries 468

Range A.275–.5"/6–12mm .079"/2mm.5"–4"/12-100mm .012"/0.3mm

4–12"/100–300mm .512"/13mm

The Digimatic Holtest is a three-point internal micrometerwith digital display (LCD).Functions include:Zero-setting, Preset, Data Hold, Inch/mm conversion,Error alarm, Data output.

Features• Efficient measurement using two measurement

modes—ABS (absolute) and INC (incremental) modes.• The 468 series provides digital readout to

.0001"/0.001mm and can be linked to the M-SPC(Mitutoyo Statistical Process Control) system.

• Battery: SR44 x 1 (541980)

• Measurement can be taken nearly up to the bottom ofthe bore.

• The display automatically turns off idle after 20 minutes.• Can measure deep holes by attaching an extension rod

(optional).• Carbide tipped contact points.

468-234

ACCURACYRange Error.275–.8" .00008"6–20mm 0.002mm.8–4" .00012"20–100mm 0.003mm4–12" .0002"100–300mm 0.005mm

DimensionsCode No. L1 L2468-956 1.77" 6.81"-6.89"468-957 2.99" 7.87"-8.03"468-958 4.02" 8.78"-9.17"468-959 4.13" 8.94"-9.45"468-960 5.94" 11.5"-12.48"

MEASURING FORCE (per Anvil)Range.275–.5"

4–20N6–20mm.5–4"

15–45N12–100mm4–12"

30–75N100–300mm

❇ Quantizing error ± 1 count.

Stand and mounting plate are optional

Optional mounting plate

982693

HOLTESTS

N-26


SpecificationsDigimatic Holtests Interchangeable-Head SetsInch/Metric

Range .275–.5"/6.985–12.7mmSet Order No. 468-956Includes:982332 Display & Thimble Unit952909 Interchangeable Head

.275–.35"/6.985–8.89mm952910 Interchangeable Head


.425–.5"/10.795–12.7mm177-179 Setting Ring .350" DIA.177-283 Setting Ring .425" DIA.952322 Extension Rod 3.94" (100mm)210187 Spanners (one pair)202863 Hex Wrench541980 SR44 Battery

Range 2–4"/50.8–101.6mmSet Order No. 468-959Includes:982335 Display & Thimble Unit982178 Interchangeable Head

2–2.5"/50.8–63.5mm982179 Interchangeable Head

2.5–3.0"/63.5–76.2mm982180 Interchangeable Head


3.5–4.0"/88.9–101.6mm177-315 Setting Ring 2.5" DIA.177-319 Setting Ring 3.5" DIA.952623 Extension Rod 5.9" (150mm)210189 Spanners (one pair)202863 Hex Wrench541980 SR44 Battery

Range .8–2"/20.32–50.8mmSet Order No. 468-958Includes:982334 Display & Thimble Unit952672 Interchangeable Head

.8–1"/20.32–25.4mm952673 Interchangeable Head

1–1.2"/25.4–30.48mm982149 Interchangeable Head


1.6–2.0"/40.64–50.8mm177-184 Setting Ring 1.000" DIA.177-291 Setting Ring 1.600" DIA.952622 Extension Rod 5.9" (150mm)210189 Spanners (one pair)202863 Hex Wrench541980 SR44 Battery

Range 4–8"/101.6–203.2mmSet Order No. 468-960Includes:982336 Display & Thimble Unit953263 Interchangeable Head

4–5"/101.6–127mm953264 Interchangeable Head

5–6"/127–152.4mm953265 Interchangeable Head

6–7"/152.4–177.8mm953266 Interchangeable Head

7–8"/177.8–203.2mm177-299 Setting Ring 5" DIA.177-303 Setting Ring 7" DIA.952623 Extension Rod 5.9" (150mm)210189 Spanners (one pair)202863 Hex Wrench541980 SR44 Battery

Range .5–.8"/12.7–20.32mmSet Order No. 468-957Includes:982333 Display & Thimble Unit952670 Interchangeable Head


.65–.8"/16.51–20.32mm177-182 Setting Ring .650" DIA.952621 Extension Rod 5.9" (150mm)210188 Spanners (one pair)202863 Hex Wrench541980 SR44 Battery

For SPC output order connecting cable 937387 (40"/1m) or 965013 (80"/2m).

Thimble Graduation .0002"

LCD ReadoutUp to 4" .00005"/0.001mmOver 4" .0001"/0.001mm

HOLTESTS

N-27


Digimatic HoltestSeries 468

SpecificationsDigimatic HoltestComplete Unit SetsInch/Metric

Individual GraduationRange Order No. Thimble LCD Readout Digimatic Holtest SETS

Set Order No. 468-966INCLUDES:

.275-.35"/ 468-231 .0002" .00005"/0.001mm 468-231 Complete gage6.925-8.89mm 468-232 Complete gage

468-233 Complete gage.35-.425"/ 468-232 .0002" .00005"/0.001mm 177-179 Setting Ring .350" DIA.8.89-10.795mm 177-283 Setting Ring .425" DIA.

210187 Spanners.425-.5"/ 468-233 .0002" .00005"/0.001mm 202863 Hex Wrench10.795-12.7mm 541980 SR44 Batteries

Set Order No. 468-967INCLUDES:

.5-.65"/ 468-234 .0002" .00005"/0.001mm 468-234 Complete gage12.7-16.51mm 468-235 Complete gage

468-236 Complete gage.65-.8"/ 468-235 .0002" .00005"/0.001mm 177-182 Setting Ring .650" DIA.16.51-20.32mm 177-287 Setting Ring .8" DIA.

210180 Spanners.8-1"/ 468-236 .0002" .00005"/0.001mm 210188 Spanners 20.32-25.4mm 202863 Hex Wrench

541980 SR44 BatteriesFor SPC output order Connecting Cable 937387 (40"/1m) or 965013 (80"/2m).

The Digimatic Holtest is a three-point internal micrometerwith digital display (LCD).

Functions include:Zero-setting, Preset, Data Hold, Inch/mm conversion,Error alarm, Data output.

Features• Efficient measurement using two measurement

modes—ABS (absolute) and INC (incremental) modes.• The 468 series provides digital readout to

.00005"/0.001mm (.0001"/0.001mm for models over 4")and can be linked to the M-SPC (Mitutoyo StatisticalProcess Control) system.

• Measurement can be taken nearly up to the bottom of the bore.

• Most of these Holtests come in sets and all can be pur-chased individually.

• Power: Silver Oxide Cell (SR-44), offers 4,500 hours of life.

• The display automatically turns off idle after 20 minutes.To restore the display turn the thimble or press thezero/ABS key.

468-966Complete UnitSets

HOLTESTS

N-28


SpecificationsDigimatic Holtests Complete Unit SetsInch/Metric

Individual Graduation Digimatic Holtests SetsRange Order No. Thimble LCD Readout (Complete Unit)

Set Order No. 468-9681–1.2"/ 468-237 .0002" .00005"/0.001mm Includes:25.4–30.48mm 468-237 Complete Gage

468-238 Complete Gage1.2–1.6"/ 468-238 .0002" .00005"/0.001mm 468-239 Complete Gage30.48–40.64mm 177-289 Setting Ring 1.2" DIA.

177-291 Setting Ring 1.6" DIA.1.6–2"/ 468-239 .0002" .00005"/0.001mm 210189 Spanners40.64–50.8mm 202863 Hex Wrench

541980 SR44 Batteries

Set Order No. 468-9692–2.5"/ 468-240 .0002" .00005"/0.001mm Includes:50.8–63.5mm 468-240 Complete Gage

468-241 Complete Gage177-315 Setting Ring 2.5" DIA.

2.5–3.0"/ 468-241 .0002" .00005"/0.001mm 210189 Spanners63.5–76.2mm 202863 Hex Wrench


Set Order No. 468-9703.0–3.5"/ 468-242 .0002" .00005"/0.001mm Includes:76.2–88.9mm 468-242 Complete Gage

468-243 Complete Gage177-319 Setting Ring 3.5" DIA.

3.5–4.0"/ 468-243 .0002" .00005"/0.001mm 210189 Spanners88.9–101.6mm 202863 Hex Wrench


4–5"/ 468-244 .0002" .0001"/0.001mm101.6–127mm

5–6"/ 468-245 .0002" .0001"/0.001mm127–152.4mm

6–7"/ 468-246 .0002" .0001"/0.001mm152.4–177.8mm

7–8"/ 468-247 .0002" .0001"/0.001mm177.8–203.2mm

8–9"/ 468-248 .0002" .0001"/0.001mm203.2–228.6mm

9–10"/ 468-249 .0002" .0001"/0.001mm228.6–254mm

10–11"/ 468-250 .0002" .0001"/0.001mm254–279.4mm

11–12"/ 468-251 .0002" .0001"/0.001mm279.4–304.8mm

For SPC output order connecting cable 937387 (40"/1m) or 965013 (80"/2mm)

DimensionsCode No. L1 L2468-231, 232, 233 1.77" 6.81"-6.89"468-234, 235 2.99" 7.87"-8.03"468-236, 237 3.46" 8.39"-8.58"468-238, 239 4.02" 8.78"-9.17"468-240, 241, 242, 243 4.13" 8.94"-9.45"468-244, 245, 246, 247, 248249, 250, 251 5.94" 11.5"-12.48"

HOLTESTS

N-29


Dial Bore Gages Series 545 – Rugged, Production-Line Tools

Features• Carbide-tipped contact point for excellent durability.• Easy zero adjustment because the Bore Gage can

stand upright.• Interchangeable anvils have a large radius of curvature

for repeatable ID measurements of roughly finishedholes.

• Two guide pins ensure high repeatability of measure-ments.

• Wide range of measurements with interchangeableanvils (screw-in type).

• .0005"(0.01mm) or .0001"(0.001mm) reading types.• Carbide tipped anvil (optional): 901484 Accuracy • .0002"/5mm

SpecificationsDial Bore GagesInchOrder No. (with Indicator) Probe Number of.0005" .0001" Range Depth Anvil545-124 545-134 1.5–2" 3.5" 5545-125 545-135 2–3" 4.5" 5545-126 545-136 3–6" 6" 7

MetricOrder No. (with Indicator) Probe Number of0.01mm 0.001mm Range Depth Anvil545-104 545-114 35–50mm 88mm 5545-105 545-115 50–75mm 113mm 5545-106 545-116 75–150mm 153mm 7

901529(A) 3.5"

901530(A) 4.5"

901531(A)10.5"

901532(A)12.5"

901533(A)15.5"

OptionalExtensions

Dep

th (

A)

Fro

m B

otto

m S

urfa

ce to

Indi

cato

rs B

ezel

.

Replacement Heads

2.64" 1.65"1.10"

No. 901955Range: 3-6"

75-150mm

No. 901956Range: 2-3"

50-75mm

No. 901957Range: 1.5-2"

35-50mm

N-30

BORE GAGES


Borematic with Absolute EncoderSeries 568

Features• LCD Readout .00005"/0.001mm.• Carbide tipped contact points ensure long life.• Efficient measurement using two measurement

modes—ABS (absolute) and INC (incremental) modes.• Can be linked to the M-SPC (Mitutoyo Statistical

Process Control) system.

• Rotatable display unit for easy reading at any angle.• Functions include:

Origin setting, Origin restoration, Zero-setting,Presetting, Data hold, Error alarm, Low-battery alarm,Data output.

• Power supply: SR44 (button-type silver oxide cell), 1 pc.

Measuring Force (per Anvil)Range .275–.5" 4–10NRange .5–5" 10–30N

AccuracyRange .275–.8" .0002"Range .8–5" .00025"❇ Quantizing error ± 1 count.

568-978

SpecificationsBorematic Interchangeable-Head SetsInch/MetricSet Set Display Adaptor Interchangeable Individual Setting RingOrder No. Measuring Range Unit Supplied Contact Heads Range Supplied w/set568-976 .275"–.5" 568-013 954595 952909 .275"–.35"/6.985–8.89mm 177-179(.35")

6.985–12.7mm 952910 .35"–.425"/8.89–10.795mm 177-283(.425")952911 .425"–.5"/10.795–12.7mm

568-977 .5"–1.0" 568-013 216556 952670 .5"–.65"/12.7–16.51mm 177-182(.65")12.7–25.4mm 952671 .65"–.8"/16. 51–20.32mm 177-287(.8")

216557 952672 .8"–1.0"/20.32–25.4mm568-978 1.0"–2.0" 568-013 216557 952673 1.0"–1.2"/25.4–30.48mm 177-289(1.2")

25.4–50.8mm 982149 1.2"–1.6"/30.48–40.64mm 177-291(1.6")982150 1.6"–2.0"/40.64–50.8mm

568-979 2.0"–4.0" 568-013 216558 982178 2.0"–2.5"/50.8–63.5mm 177-315(2.5")50.8–101.6mm 982179 2.5"–3.0"/63.5–76.2mm

982180 3.0"–3.5"/76.2–88.9mm 177-319(3.5")982181 3.5"–4.0"/88.9–101.6mm

568-980 2.0"–4.0" 568-013 216558 04AZA047* 2.0"–2.5"/50.8–63.5mm 177-315(2.5")50.8–101.6mm 2.5"–3.0"/63.5–76.2mm

04AZA048* 3.0"–3.5"/76.2–88.9mm 177-319(3.5")3.5"–4.0"/88.9–101.6mm

* Two sets of interchangeable contact points are provided.For SPC output order connecting cable 937387(40"/1m) or 965013(80"/2m).

AB

SOLUTE

TECHNOLOGY

BOREMATIC

N-31


Borematic with Absolute Encoder Series 568

568-988

Optional Extension Rods forMeasuring Deep Bores

Order No. Length Remarks952322 3.94"(100mm) for .275–.5" gages952621 5.9"(150mm) for .5–.8" gages952622 5.9"(150mm) for .8–2" gages952623 5.9"(150mm) for 2"–5" gages

AB

SOLUTE

TECHNOLOGY

c

Unit:Inch (mm)

DimensionsRange L a b c

.275-.5" 3.27" 2.28" .10" .078"(6-12mm) (83mm) (58mm) (2.5mm) (2mm).5-.8" 2.07" 2.28" .25" .012"(12-20mm) (52.6mm) (58mm) (6.3mm) (0.3mm).8-1.2" 2.29" 2.28" .35" .012"(20-30mm) (58.2mm) (58mm) (8.8mm) (0.3mm)1.2-2" 2.65" 2.28" .55" .012"(30-50mm) (67.3mm) (58mm) (14mm) (0.3mm)2-4" 2.94" 2.64" .67" .012"(50-125mm) (74.8mm) (67mm) (17mm) (0.3mm)

SpecificationsBorematic Complete-Unit SetsInch/MetricSet Set Individual Individual Setting RingOrder No. Measuring Range Order No. * Range Supplied w/set568-987 .275"–.5" 568-431 .275"–.35"/6.985–8.89mm 177-179(.35")

6.985–12.7mm 568-432 .35"–.425"/8.89–10.795mm 177-283(.425")568-433 .425"–.5"/10.795–12.7mm

568-988 .5"–1" 568-434 .5"–.65"/12.7–16.51mm 177-182(.65")12.7–25.4mm 568-435 .65"–.8"/.16.51–20.32mm 177-287(.8")

568-436 .8"–1.0"/20.32–25.4mm568-989 1.0"–2.0" 568-437 1.0"–1.2"/25.4–30.48mm 177-289(1.2")

25.4–50.8mm 568-438 1.2"–1.6"/30.48–40.64mm 177-291(1.6")568-439 1.6"–2.0"/40.64–50.8mm

568-990 2.0"–3.0" 568-440 2.0"–2.5"/50.8–63.5mm 177-315(2.5")50.8–76.2mm 568-441 2.5"–3.0"/63.5–76.2mm

568-991 3.0"–4.0" 568-442 3.0"–3.5"/76.2–88.9mm 177-319(3.5")76.2–101.6mm 568-443 3.5"–4.0"/88.9–101.6mm

568-992 2.0"–4.0" 568-446* 2.0"–2.5"/50.8–63.5mm 177-315(2.5")50.8–101.6mm 2.5"–3.0"/63.5–76.2mm

568-447* 3.0"–3.5"/76.2–88.9mm 177-319(3.5")3.5"–4.0"/88.9–101.6mm

–– 568-448* 4.0"–4.5"/101.6–114.3mm4.5"–5.0"/114.3–127mm

* Two sets of interchangeable contact points are provided.For SPC output order connecting cable 937387(40"/1m) or 965013(80"/2m).

BOREMATIC

N-32


Setting Rings Series 177

MetricOrder Outside

Size No. Accuracy Diameter Width1.0mm 177-220

1.1mm 177-222

1.2mm 177-225 ±0.0015mm 20mm 4mm

1.3mm 177-227

1.4mm 177-230

SpecificationsInch

Order OutsideSize No. Accuracy Diameter Width

.1" 177-209

.16" 177-206 .98" .28"

.24" 177-207

.275" 177-281

.35" 177-179

.425" 177-283 1.26"

.50" 177-180

.6" 177-181 1.5" .39"

.65" 177-182

.70" 177-183 1.77"

.8" 177-287

1.0" 177-184 2.09"

1.2" 177-289 ±.00006"

1.4" 177-185 2.8" .59"

1.6" 177-291

1.8" 177-186 3.35"2.0" 177-187

2.4" 177-293 .79"

2.5" 177-315 4.41"

2.8" 177-188

3.0" 177-317 4.92"3.2" 177-295

3.5" 177-319 5.51" .98"3.6" 177-189

4.0" 177-297 6.3"

5.0" 177-299 8.27"

6.0" 177-301 9.25"

7.0" 177-303 10.24"

8.0" 177-305 ±.00010" 12.24" 1.5"

9.0" 177-307 13.27"

10.0" 177-309 14.25"

11.0" 177-311 16.26"

12.0" 177-313 17.24"

MetricOrder Outside

Size No. Accuracy Diameter Width1.75mm 177-236

2.0mm 177-239 5mm

2.25mm 177-242

2.5mm 177-208

2.75mm 177-246

3.0mm 177-248

3.25mm 177-250

3.5mm 177-252 25mm

3.75mm 177-255

4.0mm 177-204 7mm

4.5mm 177-257

5.0mm 177-205

5.5mm 177-263

6.0mm 177-267

6.5mm 177-271

7.0mm 177-275

8.0mm 177-125

10.0mm 177-126 32mm

12.0mm 177-284 ±0.0015mm

14.0mm 177-132 38mm 10mm

16.0mm 177-177

17.0mm 177-133 45mm

20.0mm 177-286

25.0mm 177-139 53mm

30.0mm 177-288

35.0mm 177-140 71mm 15mm

40.0mm 177-290

45.0mm 177-178 85mm50.0mm 177-146

60.0mm 177-292

62.0mm 177-314 112mm20mm

70.0mm 177-147

75.0mm 177-316

80.0mm 177-294125mm

87.0mm 177-318140mm

25mm

90.0mm 177-148

100.0mm 177-296 160mm

125.0mm 177-298 210mm

150.0mm 177-300 235mm

175.0mm 177-302 260mm

200.0mm 177-304 ±0.0025mm 311mm 38.1mm

225.0mm 177-306 337mm

250.0mm 177-308 362mm

275.0mm 177-310 413mm

300.0mm 177-312 438mm

SETTING RINGS

N-33


AIR GAGING PRODUCTS

N-34

MSG/MLS Air Gaging Models

MSG Models

MLS Models

Specifications MSG Models MLS Models

Measuring ChannelsAir 1 standard, (optional to 4 maximum) 1 standardLVDT optional to 8 maximum 2 standardDigital optional 4, 8, 16 N/A

Measuring Programs 4 standard, optional 9 or 18 4 standardResolution .1µm minimum .1 µm minimumCommunication Ports

RS232C 1 standard (optional to 2 maximum) 1 standardRJ485 optional (2x) 2 standardUSB optional N/AOpto I/O standard standardEthernet standard N/A

Program switch Connector standard standardPrinter Port optional optional

The MSG model column is fully configurable to any air electronic application. Unit can act as master or slave in control feedback environment. Display graphics are also configurable to your specific requirements. Please contact Mitutoyo AmericaCorporation representatives for further information.The MLS model is offered as a limited measurement purpose device using a single air and two LVDT channels. LVDT's are 5pin, half bridge style.Mitutoyo also offers a complete line of air gage tooling to support our columns as well as the capability to supply tooling andmasters in many configurations for most competitive brands. In addition we can ship all gages with a long form certificationfrom our calibration labs.


Chamfer ChekSeries 526 – I.D. Measures the top diameter of tapered holes and chamfers

O.D. measures the minor end diameter of tapered conical parts

Features• Ease of operation: Simply insert the steel plunger into the

hole, press firmly against the part and read the diameterdirectly to three decimal places.

• Resolution: Reads directly to .001" for 0°–90° models.• Applications: Steel valve inserts, brass fittings, machine

tools and holders, steel check valves, circuit boards,sheet metal and stampings, pressure vessels, bronzebushings, steel governor cups.

Standard AccessoriesBlack Leather Case: (21BZA778) 9.7"(W) x 2"(D) x 6.1"(H)*Wooden Box: (21BZA779) 12.8"(W) x 5.1"(D) x 3.63"(H)

*526-006C (CI-2090) onlyMaster Plate: (64AAA012) 3"(W) x 2"(D) x .925"(H)

Optional AccessoriesSetting MasterOrder No. Model No. DiameterChamfer Chek I.D.64AAA007 SM-1000 *.375"/.750" (I.D.)64AAA008 SM-2000 *1.25"/1.75" (I.D.)64AAA133 9.525mm (I.D.)64AAA134 19.05mm (I.D.)Chamfer Chek O.D.64AAA009 SM-1000E *.375"/.750" (O.D.)*Denotes a double-sided setting master.

SpecificationsRange: 0–90°Accuracy: .001"Graduation: .001" Dia.Gage Weight: 526-005C 1 lbs. (454g)

526-006C 1.21 lbs. (545g)526-007C 1 lbs. (454g)526-008C 1 lbs. (454g)

Order No. Model No. Diameter RangeChamfer Chek I.D.526-005C CI-1090 .02–1"526-006C CI-2090** 1–2"526-005M CI-1090M 0.5–25mmChamfer Chek O.D.526-007C CO-0590 1/8–1/2"526-008C CO-1090 3/8–1"

526-005C 526-008C

526-005C shown with optional setting master.

I.D. O.D.

CHAMFER-CHEK

N-35


Digimatic Chamfer ChekSeries 547 – I.D. Measures the top diameter of tapered holes and chamfers

O.D. measures the minor end diameter of tapered conical parts

Standard AccessoriesMaster Plate (64AAA012 ), 3"(W) x 2"(D) x .925"(H)Black Leather Case (21BZA778 ) 9.7"(W) x 2"(D) x 6.1"(H)*Wooden box (21BZA779 ) 12.8"(W) x 5.1"(D) x 3.63"(H)* 547-481 (DC1-2090) only

Digimatic Chamfer ChekOrder No. Model No. Diameter Range Resolution Accuracy MassChamfer Chek I.D.547-480 DCI-1090 .02-1"/0.5-25.4mm .0005"/0.01mm ±.001"/0.025mm 1.75lbs./793g547-481 DCI-2090 1-2"/25.4-50.8mm .0005"/0.01mm ±.001"/0.025mm 3.97lbs./1,800gChamfer Chek O.D.547-482 DCO-0590 1/8"-1/2"/3.18-12.7mm .0005"/0.01mm ±.001"/0.025mm 1.75lbs./793g547-483 DCO-1090 3/8"-1"/9.52-25.4mm .0005"/0.01mm ±.001"/0.025mm 1.75lbs./793gFor SPC output order Connecting Cable 905338 (40"/1m) or 905409 (80"/2m).

547-480 547-482

547-480 Shown with optional setting master.

I.D. O.D.

CHAMFER-CHEK

N-36


Hole Chek Series 526 – Instant Diameter Measurement of Small Holes

Features• Ease of Operation: Simply insert the steel plunger into

the hole and press firmly against the part and read thediameter directly to three decimal places.

• Resolution: Reads directly in .001" diameter incre-ments.

• Applications: Inspect PC boards, screw machine parts,spray tips, injector nozzles, plastic molded parts.

Standard AccessoriesWooden Box: 12.8"(W) x 5.1"(D) x 3.2"(H)Granite Plate: 3"(W) x 2"(D) x .925"(H) (64AAAO12)

Optional AccessoriesSetting Master (O.D. = .76"/H = .29")Order No. Model No. Diameter64AAA003 SM-040 .029"64AAA004 SM-130 .078"64AAA005 SM-230 .178"64AAA006 SM-330 .278"

Specifications Accuracy: .001"Graduation: .001" Dia.Gage Weight: 526-001H 1 lbs. (454g)

526-002H 1 lbs. (454g)526-003H 1 lbs. (454g)526-004H 1 lbs. (454g)

Order No. Model No. Dia. Range526-001H HC-0040 .010"–.040"526-002H HC-0130 .030"–.130"526-003H HC-0230 .130"–.230"526-004H HC-0330 .230"–.330"

526-003H 526-001H

526-002H shown with optional setting master.

HOLE-CHEK

N-37


Date post:	30-Apr-2018
Category:	Documents
Upload:	dangdung
View:	238 times
Download:	1 times

INSIDE MEASURING INSTRUMENTS - J.W. Donchin Cojwdonchin.com/Mitutoyo/Catalog/InsideMics.pdfMITUTOYO...

Documents