• DIN Head Unit Provision with pocket • ISO Head Unit Provision with pocket• Double DIN Head Unit Provision• ISO Stacked Head Unit Provision
A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) DDIN Brackets • E) DDIN Trim Plate • F) Pocket
KIT COMPONENTS
99-9011
AB
VW EOS 2007-08/New Jetta 2005-08
GLI 2008/GTI 2006-08/Passat 2006-08Rabbit 2006-08/R32 2008/Tiguan 2009
F E
CD
TOOLS REQUIRED:
Applications
TABLE OF CONTENTS
99-9011
• Dash Disassembly - GLI 2008 ......................................................................................1,2- GTI 2006-08.................................................................................1,2- New Jetta 2005-08......................................................................1,2- Rabbit 2006-08............................................................................1,2- R32 2008 ....................................................................................1,2- Passat 2006-08 ............................................................................ 3- Tiguan 2009................................................................................... 4- Eos 2007-08................................................................................... 5
•Kit Assembly:- DIN Head Unit Provision with Pocket ............................................6- ISO Head Unit Provision with Pocket .............................................7- Double DIN Head Unit Provision.....................................................8- Stacked ISO Head Unit Provision ...................................................9
Disconnect the negative battery terminal to prevent an accidentalshort circuit.
1
Unclip and remove the grille fromthe top-center of dash. (Figure A)
2
Remove one T-20 torx screw fromblack insert from under grilleremoved in step one. (Figure B)
3
Remove insert. (Figure C)4
Remove two T-20 torx screws fromunder black insert removed in steptwo. (Figure D)
5
NEW JETTA 2005-08/GLI 2008GTI 2006-08/RABBIT 2006-08
R32 2008
2
99-9011 DASH DISASSEMBLY
E
F
GH
Unsnap and remove the vent assembly above the radio. (Figure E)
6
Remove two T-20 torx screws fromtop sides of radio/climate panel.(Figure F)
7
Remove four T-20 torx screws toremove the radio. (Figure H)
9
Remove panel. (Figure G)8
NEW JETTA 2005-08/GLI 2008GTI 2006-08/RABBIT 2006-08
R32 2008
3
99-9011 DASH DISASSEMBLY
Remove (4) T-20 Torx screws toremove radio.
3
Disconnect the negative battery terminal to prevent an accidentalshort circuit.
1
Unclip and remove trim panel sur-rounding radio. (Figure A)
2
PASSENGER AIR BAG OFF
ON
VOL
SCAN
TUNEBASS TREB BAL FAD
FM AM CD
AC
FM2 103.7MHZ
72
64
80
1 2 3 4
VW PASSAT 2006-08
A
4
99-9011 DASH DISASSEMBLY
AF
PASSENGERAIR BAG
PASSENGERAIR BAGPASSENGERAIR BAG
A
AF
PASSENGERAIR BAG
B
AF
PASSENGERAIR BAG
C
AF
D
TIGUAN 2009
Disconnect the negative battery terminal to prevent an accidentalshort circuit.
1
Unclip and remove passenger airbag light panel to the right of thehazard light button. (Figure A)
2
Remove (2) T-20 Torx screwsexposed behind the two panelsremoved in the two previous steps.(Figure B)
4
Unclip and remove the trim panelsurrounding the radio. (Figure C)
5
Remove (4) T-20 Torx screws secur-ing the radio. Unplug and remove the radio. (Figure D)
6
Unclip and remove the panel withthe two slots in it to the left of thehazard light button. (Figure A)
3
5
99-9011 DASH DISASSEMBLY
A
B
EOS 2007-08
Disconnect the negative batteryterminal to prevent an accidentalshort circuit.
1
Unclip and remove the radio trimpanel. (Figure A)
2
Remove the (4) screws securing theradio. Unplug and remove the radio.(Figure B)
3
6
99-9011 KIT ASSEMBLY
Snap the pocket into the radio hous-ing. (Figure C)
3
Slide the DIN cage into the RadioHousing and secure by bendingthe metal locking tabs down.(Figure A)
1
Slide the aftermarket head unitinto the cage and secure. (Figure B)
2
DIN HEAD UNIT PROVISION WITH POCKET
A
B
C
7
99-9011 KIT ASSEMBLY
Snap the pocket into the radio hous-ing. (Figure C)
4
Slide the head unit into the radioopening until the side clipsengage. (Figure B)
2
Snap the ISO Trim Plate into theRadio Housing. (Figure C)
3
ISO HEAD UNIT PROVISION WITH POCKET
A
B
C
Mount the ISO Brackets to thehead unit with the screws sup-plied with the unit. (Figure A)
1
8
99-9011 KIT ASSEMBLY
Slide the DDIN radio unit into theDDIN bracket/radio housing assem-bly and secure the unit to the kitusing the screws supplied with thehead unit. (Figure C)
3
Cut and remove center divide fromradio housing. (Figure A)
1
Snap the DDIN trim-plate onto thehousing/radio assembly. (Figure C)
4
Snap the DDIN brackets to theinside edge of the radio housing.(Figure B)
2
DOUBLE DIN HEAD UNIT PROVISION
A
B
C
9
99-9011 KIT ASSEMBLY
Snap the DDIN trim-plate onto thehousing/radio assembly. (Figure C)
4
Snap the DDIN brackets to theinside edge of the radio housing.(Figure B)
2
Slide the stacked ISO DIN units intothe DDIN bracket/radio housingassembly and secure the units to thekit using the screws supplied withthe head units. (Figure C)
3
STACKED ISO HEAD UNIT PROVISION
A
C
B
Cut and remove center dividerfrom radio housing. (Figure A)
1
10
FINAL ASSEMBLY
Make wiring connections using the EIA color code chart shown below and the instructions included with the headunit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individuallytape off ends of any unused wires to prevent electrical short circuit.
FINAL WIRING CONNECTIONS
99-9011 FINAL ASSEMBLY
12V Ignition / Acc . . . Red
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer . . . . . . . . . . Orange / White
Right Front (+) . . . . . Gray
Right Front (-) . . . . . . Gray/ Black
Left Front (+) . . . . . . White
Left Front (-) . . . . . . . White / Black
Right Rear (+). . . . . . Violet
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
METRA / EIA WIRING CODE
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.All colors may not be present on all leads due to manufacturer’s specifications.
1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individuallytape off the ends of any unused wires to prevent electrical short circuit.)
2 Re-connect the negative battery terminal and test the unit for proper operation.
