Publications No.
Issue DateINSTALLATIONINSTRUCTIONS
Accessory Application
© 2012 American Honda Motor Co., Inc. – All Rights Reserved. AII 47243 (1211) 1 of 2408E92-TP6-1B00-90
AII 13185REMOTE CONTROL ENGINE STARTER
2013 CROSSTOURNOV 2012
PARTS LISTRemote Engine Starter Unit KitP/N 08E91-E54-100
Transmitter
Control unit
Antenna
ID label
Remote Control Engine Starter Attachment KitP/N 08E92-TP6-100B
Engine starter harness
Control unit bracket
3 Relays
Ground bolt
18 Wire ties
3 Long wire ties(1 Not used)
7 Urethane tapes
Clip
Caution label
2 of 24 AII 47243 (1211) © 2012 American Honda Motor Co., Inc. – All Rights Reserved.
Fuse label
Accessory User’s Information Manual
Quick Start Guide
TOOLS AND SUPPLIES REQUIRED
Flat-tip screwdriverPhillips screwdriverSmall rubber malletRatchet10 mm Socket10 mm Open end wrenchTorque wrenchIsopropyl alcoholShop towelTape measureScissorsHDS/MVCIMasking tapeDiagonal cuttersRulerTapeFelt-tip penThe following tools are available through the Honda Tool and Equipment Program. On the iN, click on: Service > Service Bay > Tool and Equipment Program, then enter the number under “Search”. Or, call 888-424-6857.• Trim Tool Set (T/N SOJATP2014)• Plastic Trim Tool (T/N SILTRIMTL10)
Illustration of the Remote Control Engine Starter Installed in the Vehicle
INSTALLATION
1. Make sure you have the anti-theft codes for the audio and navigation system (if equipped), then write down the radio station presets.
2. Disconnect the negative cable from the battery.
Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
QB71858BK
ANTENNA
3 RELAYS3A, 40A FUSES
CONTROL UNIT
ENGINE STARTER HARNESS
© 2012 American Honda Motor Co., Inc. – All Rights Reserved. AII 47243 (1211) 3 of 24
3. Attach the ID label.
• Using isopropyl alcohol on a shop towel, clean the area where the ID label will attach.
• Attach the ID label to the transmitter in the area as shown.
4. Remove the driver’s sunvisor holder.
QB32111CH
ID LABEL
TRANSMITTER
Clean with isopropyl alcohol.
QB31602AH
DRIVER’S SUNVISOR HOLDER(Rotate.)
5. Wrap the end of a flat-tip screwdriver with tape. Locate the slot in the bracket cover, and insert the flat-tip screwdriver into the slot. Push the hook with the screwdriver.
6. While pushing in on the hook, rotate the driver’s sunvisor backward about 45°. Make sure the hook slides into the bracket cover.NOTE: If the hook did not stay pushed in, return the driver’s sunvisor to its original position and repeat steps 5 and 6.
QB31603AH
DRIVER’S SUNVISOR
FLAT-TIP SCREWDRIVER
TAPE
BRACKET COVER
Push the hook.
HOOK
While pushing in on the hook, rotate the sunvisor backward about 45°.
Make sure the hook slides into the bracket cover.
FRONT
4 of 24 AII 47243 (1211) © 2012 American Honda Motor Co., Inc. – All Rights Reserved.
7. Remove the driver’s sunvisor (unplug the vehicle connector).
8. Pull away the door opening seal from the driver’s A-pillar trim.
9. Using a small rubber mallet and a shop towel, gently tap the driver’s A-pillar trim at the position shown to release the clip.
QB31604AH
DRIVER’S SUNVISOR
FRONT
VEHICLE CONNECTOR
QB72101AH
CLIP
A-PILLAR TRIM
A-PILLAR
PIN
STRIKE POINT
SHOP TOWEL
SMALL RUBBER MALLET
DRIVER’S A-PILLAR TRIM
CLIPDOOR OPENING SEAL
Strike perpendicularly to the vehicle.
TRIANGLE MARK
Pull.
10. Pull away the door opening seal from the driver’s A-pillar trim. Remove the driver’s A-pillar trim (two clips).
11. Remove and discard the clip from the driver’s A-pillar trim, and install a new clip (supplied) on the driver’s A-pillar trim.
6D18070Y
2 CLIPS
DOOR OPENING SEAL
DRIVER’S A-PILLAR TRIM
6D18080Y
CLIP (Discard.)
DRIVER’S A-PILLAR TRIM
NEW CLIP
© 2012 American Honda Motor Co., Inc. – All Rights Reserved. AII 47243 (1211) 5 of 24
12. Remove the driver’s dashboard lower cover (eight clips, two hooks, and vehicle connectors).
13. Remove the driver’s dashboard under cover (three clips and one pin).
QB71601AK8 CLIPS
DRIVER’S DASHBOARD LOWER COVER
2 HOOKS
VEHICLE CONNECTORS
6D18040Y
3 CLIPS
DRIVER’S DASHBOARD UNDER COVER
PIN
14. Remove the driver’s front door sill trim (four clips, two retaining tabs, and two hooks).
15. Pull away the door opening seal, and remove the driver’s kick panel (two clips).
QB61252AK
FRONTRETAINING TAB
DRIVER’S FRONT DOOR SILL TRIM
4 CLIPS
HOOK
HOOK
RETAINING TAB
932503AS
2 CLIPS
DOOR OPENING SEAL
DRIVER’S KICK PANEL
6 of 24 AII 47243 (1211) © 2012 American Honda Motor Co., Inc. – All Rights Reserved.
16. Pull away the door opening seal, remove the driver’s dashboard side lid (three clips, four pawls, and three hooks).
17. Lower the tilt lever, and release the column band (two clips).
6D1805BY
DRIVER’S DASHBOARD SIDE LID
3 CLIPS
3 HOOKSDOOR OPENING SEAL
4 PAWLS
QB71603AK
STEERING WHEEL
PLASTIC TRIM TOOL
COLUMN BAND
2 CLIPS
18. Turn the steering wheel 90° counterclockwise. Using a plastic trim tool, release the retaining tab.
19. Turn the steering wheel 180° clockwise. Using a plastic trim tool, release the retaining tab.
QB71604AK
UPPER COLUMN COVER
PLASTIC TRIM TOOL
STEERING WHEEL
RETAINING TAB
QB71605AK
PLASTIC TRIM TOOL
RETAINING TAB
UPPER COLUMN COVER
STEERING WHEEL
© 2012 American Honda Motor Co., Inc. – All Rights Reserved. AII 47243 (1211) 7 of 24
20. Remove the upper column cover (two retaining tabs and two hooks).
21. Remove one self-tapping screw from the lower column cover.
QB71606AK
2 RETAINING TABS
2 HOOKS
UPPER COLUMN COVER
QB71610AK
LOWER COLUMN COVER
STEERING WHEEL
SELF-TAPPING SCREW
22. Turn the steering wheel 180° counterclockwise, and remove the other self-tapping screw from the lower column cover.
23. Remove the lower column cover (one self-tapping screw).
QB71609AK
LOWER COLUMN COVER SELF-TAPPING
SCREW
STEERING WHEEL
QB71607AK
LOWER COLUMN COVER
SELF-TAPPING SCREW
8 of 24 AII 47243 (1211) © 2012 American Honda Motor Co., Inc. – All Rights Reserved.
24. Remove the vehicle unit (two bolts and vehicle connectors).
Installing the Antenna
25. Using scissors, cut one urethane tape in half. Wrap two halves of urethane tape to the antenna cable as shown.
QB71602AK
BOLT
VEHICLE CONNECTORS (if equipped.)
VEHICLE UNIT
BOLT
QB62501BK
ANTENNA
60 mm (2.4 in.)
60 mm (2.4 in.)
HALVES OF URETHANE TAPE(Do not fold the antenna cable.)
URETHANE TAPE(Cut in half.)
ANTENNA CABLE
26. Starting near the antenna end of the cable, wrap two urethane tapes around the antenna cable at the measurements shown.
27. Using scissors, cut one urethane tape in half. Wrap the two halves of urethane tape around the antenna cable at the measurements shown.
QB71701BK
ANTENNA CABLE
2 URETHANE TAPES
ANTENNA
220 mm(8.7 in.)
540 mm(21.3 in.)
ANTENNA CABLE
2 HALVES OF URETHANE TAPES
URETHANE TAPE(Cut in half.)
© 2012 American Honda Motor Co., Inc. – All Rights Reserved. AII 47243 (1211) 9 of 24
28. Attach the antenna.• Attach masking tape to the windshield at the
measurement shown.
With Camera Cover
Without Camera Cover
QB51403BH
CAMERA COVER
HEADLINER
10 mm (0.4 in.)
MASKING TAPE
QB51402BH
MASKING TAPE
50 mm (2.0 in.)
HEADLINER
• Fold the adhesive backing of the antenna as shown.
• Using isopropyl alcohol on a shop towel, thoroughly clean the windshield where the antenna will attach.
• Attach the antenna with masking tape. Adjust position of the antenna so there is equal spacing on both sides.
QB51401CH
ANTENNA
ADHESIVE BACKING
QB51404CH
Clean with isopropyl alcohol.
ANTENNA
MASKING TAPE
HEADLINER
ANTENNA
Equal spacing on both sides.
10 of 24 AII 47243 (1211) © 2012 American Honda Motor Co., Inc. – All Rights Reserved.
• Carefully remove the adhesive backing from the antenna, and attach the antenna to the windshield. Press and hold the antenna firmly in place for 30 seconds.
• Remove the masking tape.
29. Gently pull down the headliner, and tuck the antenna cable under the headliner. Be careful not to crease the headliner.
QB51405CH
ADHESIVE BACKING(Remove.)
ANTENNA
MASKING TAPE (Remove.)
QB71702AK
HEADLINER
ANTENNA CABLE
ANTENNA
30. Route the antenna cable down the A-pillar as shown. Using four wire ties, secure the antenna cable to the vehicle harness.
31. Pull away the door opening seal. Route the antenna cable down and under the dashboard through the driver’s A-pillar trim opening.
QB71703AK
WIRE TIE
Be careful not to secure the wire ties over the holes.
4 WIRE TIES
VEHICLE HARNESS
ANTENNA CABLE
VEHICLE HARNESS
ANTENNA CABLE
VEHICLE FRAME
QB71704AK
DASHBOARD
DOOR OPENING SEAL(Pull away.)
DRIVER’S A-PILLAR TRIM OPENING
ANTENNA CABLE
© 2012 American Honda Motor Co., Inc. – All Rights Reserved. AII 47243 (1211) 11 of 24
Routing the Engine Starter Harness
32. Using isopropyl alcohol on a shop towel, clean the areas where the fuse labels will attach.
33. Attach the 40A fuse labels and 3A fuse labels to the engine starter harness relay block and fuse block.
34. Install the three relays to the engine starter harness relay block.
QB71854AK
Clean with isopropyl alcohol.
40A FUSE LABEL
Clean with isopropyl alcohol.
3A FUSE LABEL
RELAY BLOCK
40A FUSE LABEL
3A FUSE LABEL
FUSE BLOCK
QB71855AK
RELAY BLOCK
3 RELAYS
35. Route the 12-pin/10-pin connector ends of the engine starter harness over the vehicle bracket towards the center of the vehicle.
36. Align the white tape on the engine starter harness with the clip on the vehicle harness, and secure the engine starter harness to the vehicle harness using one wire tie.
37. Using one long wire tie, secure the engine starter harness to the vehicle harness.
QB71856BK
ENGINE STARTER HARNESS 12-PIN/10-PIN CONNECTORS
STEERING SHAFT
VEHICLE BRACKET
QB71713BK
CLIP ON THE VEHICLE HARNESS
WHITE TAPE
WIRE TIE
ENGINE STARTER HARNESS
VEHICLE HARNESS
LONG WIRE TIE
12 of 24 AII 47243 (1211) © 2012 American Honda Motor Co., Inc. – All Rights Reserved.
38. Align the white tape on the engine starter harness with the clip on the vehicle harness, and secure the engine starter harness to the vehicle harness using one wire tie.
39. Using one wire tie, secure the engine starter harness to the vehicle harness.
40. Unplug the vehicle 12-pin connector, and plug it into the engine starter harness 12-pin connector. Plug the remaining engine starter harness 12-pin connector into the combination light switch.
QB90301AK
CLIP ON THE VEHICLE HARNESS
WHITE TAPE
2 WIRE TIES
ENGINE STARTER HARNESS
VEHICLE HARNESS
QB71850AK
ENGINE STARTER HARNESS
ENGINE STARTER HARNESS 12-PIN CONNECTOR
ENGINE STARTER HARNESS 12-PIN CONNECTOR
VEHICLE 12-PIN CONNECTOR
COMBINATION LIGHT SWITCH
41. Unplug the vehicle 10-pin connector, and plug it into the engine starter harness 10-pin connector. Plug the remaining engine starter harness 10-pin connector into the wiper switch.
QB71851AK
ENGINE STARTER HARNESS 10-PIN CONNECTOR
VEHICLE 10-PIN CONNECTORWIPER
SWITCH
ENGINE STARTER HARNESS
© 2012 American Honda Motor Co., Inc. – All Rights Reserved. AII 47243 (1211) 13 of 24
42. Align the white tape on the engine starter harness with the clip on the vehicle harness, and secure the engine starter harness to the vehicle harness using one wire tie.
QB71852AK
ENGINE STARTER HARNESS
WIRE TIE
Do not undue strain to the 12-pin connector cord.
CLIP ON THE VEHICLE HARNESS
WHITE TAPE
VEHICLE HARNESS
43. Align the white tape on the engine starter harness with the clip on the vehicle harness, and secure the engine starter harness to the vehicle harness using one wire tie.NOTE: Make sure that the connectors and harness are not pinched, or are not interfering with the steering wheel when it is moved for adjustment.
QB71853AK
WIRE TIE
VEHICLE HARNESS
Do not undue strain to the 10-pin connector cord.
WHITE TAPE
CLIP ON THE VEHICLE HARNESS
ENGINE STARTER HARNESS
14 of 24 AII 47243 (1211) © 2012 American Honda Motor Co., Inc. – All Rights Reserved.
44. Using one long wire tie, secure the engine starter harness to the vehicle harness.
45. Using two wire ties, secure the engine starter harness to the vehicle harness.
46. Using scissors, cut one urethane tape to the measurements shown. Wrap the cut urethane tape around the engine starter harness 5-pin connector.
QB71801AK
2 WIRE TIES
VEHICLE HARNESS LONG WIRE TIE ENGINE
STARTER HARNESS
VEHICLE HARNESS
QB71857AK
20 mm (0.8 in.)
ENGINE STARTER HARNESS
25 mm (1.0 in.)
URETHANE TAPE
VIEWED FROM URETHANE SIDE
ENGINE STARTER HARNESS 5-PIN CONNECTOR
47. Unplug the vehicle 5-pin connector from the fuse box. Plug the engine starter harness 5-pin connector into the fuse box 5-pin connector. Plug the vehicle 5-pin connector into the engine starter harness 5-pin connector.
NOTICE: Make sure the engine starter harness 5-pin connector is securely connected to the fuse box 5-pin connector. A loose connection can cause the engine to stall during driving.
QB71804AK
Push.
VEHICLE 5-PIN CONNECTOR
ENGINE STARTER HARNESS 5-PIN
13
1 2
Plug.Unplug.
Push. Pull.
Connector unlock Connector lock
2
FUSE BOX
© 2012 American Honda Motor Co., Inc. – All Rights Reserved. AII 47243 (1211) 15 of 24
48. Using one wire tie, secure the engine starter harness and antenna cable to the vehicle harness.
49. Plug the engine starter harness 12-pin connector into the fuse box.
QB90302AK
ENGINE STARTER HARNESS ANTENNA
CABLE
WIRE TIE
VEHICLE HARNESS
FUSE BOX
QB71702AJENGINE STARTER HARNESS 12-PIN CONNECTOR
12-PIN CONNECTOR
FUSE BOX
50. Attach the engine starter harness 25-pin connector to the vehicle connector as shown.
51. Unplug the vehicle 25-pin connector from the fuse box. Plug the engine starter harness 25-pin connector into the fuse box 25-pin connector. Plug the vehicle 25-pin connector into the engine starter harness 25-pin connector.
QB71705AJ
ENGINE STARTER HARNESS25-PIN CONNECTORVEHICLE
CONNECTOR
QB71706AJ
VEHICLE 25-PIN CONNECTOR
FUSE BOX
VEHICLE 25-PIN CONNECTOR
ENGINE STARTER HARNESS 25-PIN CONNECTORS
16 of 24 AII 47243 (1211) © 2012 American Honda Motor Co., Inc. – All Rights Reserved.
52. Remove the vehicle bolt, and install the engine starter harness ground terminal using the ground bolt.
53. Using one wire tie, secure the engine starter harness to the vehicle harness.
QB71707AJ
ENGINE STARTER HARNESS
GROUND BOLT
VEHICLE BOLT (Discard.)
HOOD OPENER
QB71708AJ
VEHICLE HARNESS
WIRE TIE
ENGINE STARTER HARNESS
54. Using one wire tie, secure the engine starter harness and antenna cable to the vehicle harness.
55. Plug the antenna cable connector and engine starter harness 28-pin connector into the control unit.
QB71709AJ
VEHICLE HARNESS WIRE TIE ENGINE STARTER
HARNESS
ANTENNA CABLE
QB22204BK
CONTROL UNIT
ANTENNA CABLE CONNECTOR
ENGINE STARTER HARNESS 28-PIN CONNECTOR
© 2012 American Honda Motor Co., Inc. – All Rights Reserved. AII 47243 (1211) 17 of 24
56. Install the control unit bracket to the control unit.
57. Remove the vehicle nut and loosen the vehicle nut.
QB71712AJ
CONTROL UNIT
CONTROL UNIT BRACKET
QB71713AJ
BRAKE PEDAL BRACKET
VEHICLE NUT (Loosen.)
VEHICLE NUT (Remove.)
58. Secure the control unit bracket to the brake pedal bracket with two vehicle nuts.• Vehicle nuts
Torque: 9.8 - 15.7 N·m (1.0 - 1.6 kgf·m, 7.2 - 11.6 lbf·ft)
59. Using a felt-tip pen, mark the control unit bracket and vehicle nuts.
QB71714AJ
CONTROL UNIT BRACKET
BRAKE PEDAL BRACKET
VEHICLE NUT
VEHICLE NUT (reused)
CONTROL UNIT BRACKET
QB91101AJ
CONTROLUNITBRACKET
FELT-TIP PEN
MARK 2 VEHICLENUTS
18 of 24 AII 47243 (1211) © 2012 American Honda Motor Co., Inc. – All Rights Reserved.
60. Attach the engine starter harness relay block to the control unit bracket.
61. Align the white tape on the engine starter harness with the clip on the vehicle harness, and secure the engine starter harness and antenna cable to the vehicle harness using one wire tie.
62. Using one wire tie, secure the engine starter harness and antenna cable to the vehicle harness.
QB71952AK
CONTROL UNIT BRACKET
ENGINE STARTER HARNESS RELAY BLOCK
QB71950AK
VEHICLE HARNESS
WHITE TAPE2 WIRE TIES
ANTENNA CABLE
ENGINE STARTER HARNESS
CLIP ON THE VEHICLE HARNESS
63. Using one wire tie, secure the antenna cable to the engine starter harness.
64. Bundle up the excess antenna cable as shown. Using one wire tie, secure the antenna cable and engine starter harness to the vehicle harness.
QB71953BK
ENGINE STARTER HARNESS
WIRE TIE
ANTENNA CABLE
CONTROL UNIT
QB71902BK
VEHICLE HARNESS
WIRE TIEANTENNA CABLE(Bundle.)
ENGINE STARTER HARNESS
100 mm (3.9 in.)20 mm (0.8 in.) or above.
© 2012 American Honda Motor Co., Inc. – All Rights Reserved. AII 47243 (1211) 19 of 24
65. Using scissors, cut one urethane tape to the measurement shown. Using isopropyl alcohol on a shop towel, clean the vehicle unit (removed in step 24) where one urethane tape will attach.
66. Attach the urethane tape to the vehicle unit in the area as shown. Reinstall the vehicle unit.
67. Using isopropyl alcohol on a shop towel, clean the lower column cover where one urethane tape will attach.
68. Attach the urethane tape to the lower column cover in the area as shown.
QB71805BK
URETHANE TAPE Clean with
isopropyl alcohol.
VEHICLE UNIT
80 mm (3.1 in.)
80 mm (3.1 in.)URETHANE TAPE (Cut.)
QB71718AJ
URETHANE TAPE
Clean with isopropyl alcohol.
LOWER COLUMN COVER
69. Using isopropyl alcohol on a shop towel, clean the hood where the caution label will attach.
70. Attach the caution label to the hood in the area shown.
71. Check that all wire harnesses are routed properly and all connectors are plugged in.
72. Check the overlap between the headliner and the driver’s A-pillar trim. Refer to the Service Manual. If necessary, adjust the overlap.
73. Check the marks (step 59) of the nuts and the control unit bracket.
74. Reinstall all removed parts.75. Reconnect the negative cable to the battery.76. Enter the anti-theft codes for the radio and
navigation systems, then enter the customer’s radio presets.
77. Reset the clock.78. Perform the “REMOTE ENGINE STARTER
REGISTRATION” and the “FUNCTION CHECK”.
932517AS
HOOD(Clean with isopropyl alcohol.)
CAUTION LABEL
ADHESIVE BACKING (Remove.)
20 of 24 AII 47243 (1211) © 2012 American Honda Motor Co., Inc. – All Rights Reserved.
REMOTE ENGINE STARTER REGISTRATION1. Acquire the PCM Code from the Interactive Network.
2. Connect the HDS/MVCI tester to the OBD II data link connector, then turn the ignition switch to the on (II) position.
3. Start the HDS, and click the car icon.
4. Input the VIN and other required information into the HDS, then click the check button.
QB91102AJ
CAR ICON
QB32102BH
Input the VIN and other required information. CHECK BUTTON
5. Select Honda Systems, then click the check button.
6. Select R/C ENG STARTER and click the check button.
QB32103AH
Select “Honda Systems.”
CHECK BUTTON
QB32104AH
Select “R/C ENG STARTER.”
CHECK BUTTON
© 2012 American Honda Motor Co., Inc. – All Rights Reserved. AII 47243 (1211) 21 of 24
7. Select REGISTER REMOTE CONTROL ENGINE STARTER UNIT, then click the check button.
8. The following message will display: Obtain PCM-code (IMMOBILIZER PCM CODE) from iN. This vehicle’s VIN will be required to obtain the password. (USA) Click the check button.
QB32105BH
Select “REGISTER REMOTE CONTROL ENGINE STARTER UNIT.”
CHECK BUTTON
QB32106AH
“Obtain PCM-code” message.
CHECK BUTTON
9. Input the PCM-code, then click the check button.NOTE: To ensure security, the PCM-code (password) is changed everyday, so it is impossible to register the remote control engine starter if the dates of the PCM-code acquisition and registration are different. The date of the HDS/MVCI tester should also be the same.
10. The following message will display: The registration of the Remote Control Engine Starter Unit has been completed. Turn the ignition switch off.
QB32107BH
Input the PCM-Code.
CHECK BUTTON
22 of 24 AII 47243 (1211) © 2012 American Honda Motor Co., Inc. – All Rights Reserved.
11. The following message will display: Check that engine can be started by the Transmitter. Click the check button.
QB32108CH
“The registration of the Remote Control Engine Starter Unit has been completed.”
© 2012 American Honda Motor Co., Inc. – All Rights Reserved. AII 47243 (1211) 23 of 24
12. Perform the FUNCTION CHECK on page 23, then disconnect the HDS/MVCI.
FUNCTION CHECK
Operating Conditions
• The hood is closed• The shift lever is in park• Turn the ignition switch off and the key is outside the vehicle• All doors and tailgate closed and locked
Inspection
1. Press the engine/command button on the transmitter and release, within 2 seconds, press the lock/start button on the transmitter.The engine should start if all operating conditions are met. (Refer to the engine starter operation.)
Does the engine start?
Yes - Operation is normal.
No:
• Make sure all “Operating Conditions” are met.
• Check the engine starter harness connections.
• Connect the HDS/MVCI and check for an indicated
failure. (Refer to the appropriate Service Manual for
details.)
QB32109CH
“Check that engine can be started by the Transmitter.”
CHECK BUTTON
24 of 24 AII 47243 (1211) © 2012 American Honda Motor Co., Inc. – All Rights Reserved.
2.Press the engine/command button on the transmitter and release, within 2 seconds, press the unlock/stop button. The engine should stop.
Does the engine stop?
3. After the engine has stopped, start the engine again, and check that the engine stops after each of the following conditions:
NOTE: After each test the ignition key must be cycled, or the driver’s door must be opened and closed.
• Move the shift lever out of the P position.• Unlock or open the doors or the tailgate.• Open the hood.• Insert the key in the ignition.• Press on the brake pedal.
Does the engine stop after each of these tests?
4. Check that the power windows and the moonroof do not function, and the shift lever does not move to any position when the engine is started with the transmitter.
5. Start the engine again, press the engine/command button on the transmitter two times, and check the vehicle condition on the display.
6. Check the operation of the transmitter when the vehicle is 120 m (400 ft.) away and in direct sight.
Yes - Operation is normal.
No - Check the engine starter harness connections.
Yes - Operation is normal.
No - Check the engine starter harness connections.
B127121H
ENGINE/COMMAND BUTTON
UNLOCK/STOP BUTTON
RECEPTION INDICATOR
CHECKING INDICATOR
ENGINE START OPERATION
Blinking
ENGINE RUNNING INDICATOR
IN-CAR TEMPERATURE*1
REMAINING IDLING TIME*1
*1 Only on vehicles equipped with the automatic climate control.This indicator is displayed for some vehicles among them.
LOCK/START BUTTON
7. Press the unlock/stop button on the transmitter and verify that the doors unlock. Press the lock/start button, and verify that the doors lock.
8. Check that the engine can start by the vehicle key and that the wiper and the headlight can be operated normally.