INSTALLATION GUIDESIGNATURE SERIES SHEDS

BUILDING SHELL CONSTRUCTION

CHAPTER 1

CHAPTER 2

CHAPTER 3

FOUNDATION PREPARATION

WALLS

ROOF

RECOMMENDED TOOLS:

DRILL DRIVERWOOD DRILL BIT SET3/4' PADDLE BIT

IMPACT DRIVER1/4" NUT DRIVER BIT#2 PHILLIPS BIT#3 PHILLIPS BITT25 TORQUE BITT30 TORQUE BIT

3/8" CROWN STAPLERT-50 ROOF STAPLES, SEE PROVIDED SHOPPING LIST

PNEUMATIC FRAMING NAILER3" 16d NAILS, SEE PROVIDED SHOPPING LIST2 3/8" 8d NAILS, SEE PROVIDED SHOPPING LIST

OSCILATING MULTI TOOL

COMPRESSOR

10 oz CAULK GUN

UTILITY KNIFE

HAMMER DRILL (CONCRETE SLABS ONLY)1/2" MASONRY BIT3/4" MASONRY BIT MAY BE REQUIRED, SEE PERMIT PLAN SET

COMPOUND MITER SAW

GENERAL CARPENTRY TOOLS (6-ft LEVEL, TIN SNIPS, HAMMER, MEASURING TAPE, CHALK LINES, PENCILS, SQUARE, ETC.)

6-FT LADDER MINIMUM

INSTALLATION DRAWINGSSEE ATTACHMENTS TO THE 'STUDIO SHED SHIPMENT UPDATE' EMAIL

** IMPORTANT **SAFETY IS YOUR #1 RESPONSIBILITY. ALWAYS WEAR TASK APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT (PPE) SUCH AS OSHA-

APPROVED GLASSES, GLOVES, WORK BOOTS, ETC.

*CONTACT InstallationSupport@studioshed.com FOR QUESTIONS*

1TABLE OF CONTENTS AND REQUIRED TOOLSSIGNATURE SERIES INSTALLATION GUIDE

2FOUNDATION PREPSIGNATURE SERIES INSTALLATION GUIDE

Fig 2a:

Fig 2b:

3FOUNDATION PREPSIGNATURE SERIES INSTALLATION GUIDE

Fig 3a:

Fig 3b:

4FOUNDATION PREPSIGNATURE SERIES INSTALLATION GUIDE

Fig 4a:

Fig 4b:

5WALLSSIGNATURE SERIES INSTALLATION GUIDE

Fig 5a:

Fig 5b:

6WALLSSIGNATURE SERIES INSTALLATION GUIDE

Fig 6a:

Fig 6b:

7WALLSSIGNATURE SERIES INSTALLATION GUIDE

Fig 7a:

Fig 7b:

836" DOOR FRONT WALLSSIGNATURE SERIES INSTALLATION GUIDE

Fig 8a:

Fig 8b:

972" DOOR FRONT WALLSSIGNATURE SERIES INSTALLATION GUIDE

Fig 9a:

Fig 9b:

10WALLSSIGNATURE SERIES INSTALLATION GUIDE

Fig 10a:

Fig 10b:

11ANCHORING WALLS TO CONCRETE FOUNDATIONSIGNATURE SERIES INSTALLATION GUIDE

Fig 11a:

Fig 11b:

12WALLSSIGNATURE SERIES INSTALLATION GUIDE

Fig 12a:

Fig 12b:

13WALLSSIGNATURE SERIES INSTALLATION GUIDE

Fig 13a:

Fig 13b:

14WALLSSIGNATURE SERIES INSTALLATION GUIDE

Fig 14a:

CAULKING LOCATION SHOWN ABOVE IN GREY

15ROOFSIGNATURE SERIES INSTALLATION GUIDE

Fig 15a:

Fig 15b:

16ROOFSIGNATURE SERIES INSTALLATION GUIDE

Fig 16a:

Fig 16b:

17ROOFSIGNATURE SERIES INSTALLATION GUIDE

Fig 17a:

Fig 17b:

18ROOFSIGNATURE SERIES INSTALLATION GUIDE

Fig 18a:

Fig 18b:

19ROOFSIGNATURE SERIES INSTALLATION GUIDE

Fig 19a:

Fig 19b:

Fig 20a:

Fig 20b:

CORRECT

SEALING MATERIAL SLIGHTLYVISIBLE AT EDGE OF WASHER.ASSEMBLY IS WATER TIGHT.

TOO LOOSE!

SEALING MATERIAL IS NOTVISIBLE; NOT ENOUGH

COMPRESSION TO SEAL.

TOO TIGHT!

WASHER IS DEFORMED;SEALING MATERIAL PRESSED

BEYOND FASTENER EDGE.

*DO NOT OVERTIGHTEN SCREWS!

- STEP 4: INSTALL NEOPRENE WASHER SCREWS, 12” ON CENTER VERTICALLY, ALONG PEAKS AT PANEL OVERLAPS

Fig 20c:

20ROOFSIGNATURE SERIES INSTALLATION GUIDE

21ROOFSIGNATURE SERIES INSTALLATION GUIDE

Fig 21a:

Fig 21b:

22ROOFSIGNATURE SERIES INSTALLATION GUIDE

Fig 22a:

Fig 22b:

*FOR NEXT STEPS SEE TRIM AND SIDING INSTALLATION RESOURCES.