.comPhone (800) 526.2588Fax (800) 526.2585
Headquarters/Eastern Distribution Center44 Harbor Park Drive Port Washington, NY 11050
Central Distribution Center1600 Distribution CtLithia Springs, GA 30122
Western Distribution Center 1750 Archibald Avenue Ontario, CA 91760
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
INSTALLATION INSTRUCTION758 – LED Wall Sconce
WS-75818
HARDWARE
A B C D E
Wire ConnectorQty: 3pcs+1 Extra7EAC112201
Junction Box ScrewQty: 2pcs+1 Extra7MPF0820C1#8-32x13/16Nickel Plating
Wood Screw Qty: 2pcs+1 Extra7MPF2204J2Ф4X22
Plastic Anchor Qty: 2pcs+1 Extra7TDD082401
Mounting ScrewQty: 1 Extra7MPF0412S1(AL)5/32-32x1/2Nickel Plating
PD-87741877-LED Pendant
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improv ement program. G0
ScrewQty:1 Extra
1/8"-40×1/2 Chrome Plating
Optional Metal CapQty:1 Extra
Chrome Plating
Wire ConnectorQty: 3pcs+1 Extra
P3
Junction Box ScrewQty: 2pcs+1 Extra
8#-32×13/16Nickel Plating
Mounting ScrewQty:1 Extra
5/32"-32×1/2Chrome Plating
A D EB C
PD-27802278-LED Pendant
Wire Connector
Qty: 3pcs+1 Extra
P3
Junction Box Screw
Qty: 2pcs+1 Extra
8#-32×13/16
Nickel Plating
Mounting Screw
Qty:1 Extra
5/32"-32×1/2
Chrome Plating
A B C
FM-W57806(F)/ FM-W57809(F)/ FM-W57812(F)578 – LED Outdoor
A B C D
FM-W57806/ FM-W57809/ FM-W57812/FM-W57806F/ FM-W57809F/ FM-W57812F
578 – LED Outdoor
INSTALLATION INSTRUCTION
waclighting.comPhone (800) 526.2588Fax (800) 526.2585
Headquarters/Eastern Distribution Center44 Harbor Park Drive Port Washington, NY 11050
Central Distribution Center1600 Distribution CtLithia Springs, GA 30122
Western Distribution Center 1750 Archibald Avenue Ontario, CA 91760
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
PREPARATION
1. Shut off the power at the circuit breaker and remove existing fixture, including the crossbar.2. Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not to lose any sm
all parts necessary for
installation.
MOUNTING THE FIXTURE (Fig. 1)3. Remove the mounting screw (E) from the mounting back plate.4. Drill holes in the wall aligned with the key holes located in the mounting back plate, insert the plastic anchors (D).5. Secure the mounting plate to the junction box using junction box screws (B), fasten it to the wall using wood screws (C). The side of
the mounting back plate marked “GND” must face out.
CONNECTING THE WIRES (Fig. 2)6. Connect the driver input/output wires to junction box wires as shown in
Fig. 2, making sure that all wire connectors (A) are secured. If your outlet box has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box. * Requires Driver to be recessed within the junction box.
COMPLETING THE INSTALLATION (Fig. 1)7. Secure the fixture to the mounting back plate using the mounting screw (E).
4 1/8”
1 3/4”
Fixture Wires
Black or Smooth
Fixture Wires
White or Ribbed
Fixture Wires
Bare wire(Ground)
House Wires
Black(Hot)
House Wires
White (Neutral)
House Wires
Green or Bare Copper(Ground)
Fig.2 Wiring
Junction Box
Wire Connector
Driver
Plastic Anchor
Mounting Plate
Wood Screw
Mounting Screw
A
D
C
E
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. G0
Ground Wire Screw
3. Remove the mounting screw (C) from the fixture.
5. Secure the mounting back plate to the junction box using junction box screws (B).The side of the mounting back plate marked “GND” must face out.
6. Secure the canopy to the mounting plate using the mounting screw (C).
4. Connect the Driver’s input wires to junction box wires as shown in Fig. 2, making sure that all wire connectors (A) are secured. If your outlet box has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
CONNECTING THE WIRES (Fig. 2)
1.
Shut o
ff the power at the circuit breaker and rem
ove existing fixture, including the crossbar.
2. Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not lose any small parts necessary for installation.
PREPARATION
MOUNTING THE FIXTURE(Fig.1)
7. There is optional metal clip in hardware bag, remove the screw (D) to replace the plastic clip, secure the metal clip with screw (D).
Fixture WiresBlack or Smooth
Fixture WiresWhite or Ribbed
Fixture WiresBare wire(Ground)
House WiresBlack(Hot)
House WiresWhite (Neutral)
House WiresGreen or Bare Copper(Ground)
Fig.2 Wiring
10 5
/16"
3. Remove the mounting screw (C) from the canopy.
6. Secure the mounting back plate to the junction box using junction box screws (B).The side of the mounting back plate marked “GND” must face out.
4. Adjust the fixture wire length by pushing the cable gripper on the canopy and pulling the wire as desired. Make sure the wires are the same length.5. Connect the Driver’s input wires to junction box wires as shown in Fig. 2, making sure that all wire connectors (A) are secured. If your outlet box has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
CONNECTING THE WIRES (Fig. 2)
1.
Shut o
ff the power at the circuit breaker and rem
ove existing fixture, including the crossbar.
2. Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not lose any small parts necessary for installation.
PREPARATION
MOUNTING THE FIXTURE(Fig.1)
Fixture WiresBlack or Smooth
Fixture WiresWhite or Ribbed
Fixture WiresBare wire(Ground)
House WiresBlack(Hot)
House WiresWhite (Neutral)
House WiresGreen or Bare Copper(Ground)
Fig.2 Wiring
Ground Wire Screw
Plate
7. Hook the safety cord to the mounting plate.
8. Secure the canopy to the mounting plate using the mounting screw (C).
Junction Box
Wire Connector
Canopy
Junction Box Screw
Mounting Screw
Input Wires
4. Secure mounting plate to the junction box using junction box screws (B).The side of the mounting plate marked “GND” must face out.5. Place the canopy over the mounting plate and secure with mounting screws.
3. Connect the fixture wires with supply wires as shown in Fig. 2, making sure all wire connector(A) are secured. If your outlet box has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate using the green screw provided. After all wires are connected, tuck them carefully inside the junction box.
CONNECTING THE WIRES (Fig. 2)
1. Shut off the power at the circuit breaker and remove existing fixture, including the crossbar.2. Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not lose any small parts necessary for installation.
PREPARATION
MOUNTING THE FIXTURE (Fig. 1)
6. Twist lock the acrylic shade into the canopy, then lock it with allen screw (C) using allen wench (D).
Fixture WiresBlack or Smooth
Fixture WiresWhite or Ribbed
Fixture WiresBare wire(Ground)
House WiresBlack(Hot)
House WiresWhite (Neutral)
House WiresGreen or Bare Copper(Ground)
Fig.2 Wiring
Ø4"
Mounting Plate Dimensions7MBC101501
1 3/4”
1 3/8”
FIG.1
INSTALLATION INSTRUCTIONS
578 - LED OutdoorFM-W57806/FM-W57809/FM-57812/FM-W57906F/FM-W57809F/FM-57812F
1
.comPhone (800) 526.2588Fax (800) 526.2585
Headquarters/Eastern Distribution Center44 Harbor Park Drive Port Washington, NY 11050
Central Distribution Center1600 Distribution CtLithia Springs, GA 30122
Western Distribution Center 1750 Archibald Avenue Ontario, CA 91760
HARDWARE
INSTALLATION INSTRUCTION578 - LED Outdoor
FM-W57815
Wire ConnectorQty: 3 pcs +1 Extra
7EAC112201P3
A
Junction Box ScrewQty: 2 pcs + 1 Extra
7MPF0#8-32×
B
Allen ScrewQty: 1pc xtra
5/32”-32 xNickel Plating
C
Allen WrenchQty: 1 pc
7MPE205001
D
G0
2
.comPhone (800) 526.2588Fax (800) 526.2585
Headquarters/Eastern Distribution Center44 Harbor Park Drive Port Washington, NY 11050
Central Distribution Center1600 Distribution CtLithia Springs, GA 30122
Western Distribution Center 1750 Archibald Avenue Ontario, CA 91760
INSTALLATION INSTRUCTION578 - LED Outdoor
FM-W57815
FIG. 1
Ø4"
1 3/8"
1 3/4"
Wire Connector
Allen Wrench
Allen Screw
Junction Box Screw
Canopy
Mounting Screw
Acrylic Lampshade(Included inside Lampshade)
Mounting Plate
Input Wires
Junction Box
A
D
C
B
Fixture Wires
Black or Smooth
Fixture Wires
White or Ribbed
Fixture Wires
Bare wire(Ground)
House Wires
Black(Hot)
House Wires
White (Neutral)
House Wires
Green or Bare Copper(Ground)
Fig. 2 Wiring
PREPARATION
1. Shut off the power at the circuit breaker and remove existing fixture, including the crossbar.2. Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
CONNECTING THE WIRES (Fig. 2)3. Connect the fixture wires with supply wires as shown Fig. 2 sure all wire connector (A) are secure. If your outlet box has a green
or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate using the green screw provided. After all wires are connected, tuck them carefully inside the junction box.
MOUNTING THE FIXTURE (Fig. 1)Secure mounting plate to the junction box using junction box screws (B).
The side of the mounting plate marked “GND” must face out.Place the canopy over the mounting plate and secure with mounting screws.Twist lock the glass into the canopy, then lock it with llen screw (C) using llen wench (D).
G0
Mounting Plate Dimensions
7MBC101501