1

Installation Instructions for 920E4 -LED AIC

Round or Square 4”

E4_-L_AI 1.5

Install the Housing with Adjustable Bars

1

2

3

Slide the inner adjustable bar completely through thethree housing clasps. Make sure the nail is on top.

Slide and push the outer adjustable bar completely ontothe inner adjustable bar so that the tab clicks into placebehind the stop point.This will prevent the adjustable barsfrom coming apart.

Repeat steps 2 & 3 for the other side of the housing.

HOUSING CLASP

HOUSING1A INNER ADJUSTABLE BAR

OUTER ADJUSTABLE BAR

TAB

STOP POINT

2

3

NAIL

1

1D

1B

COLLAR

NAIL

JOISTNAIL

4 4

5

5

NOTE: The adjustable bars can be mounted to

joists that are spaced 16" - 24" apart.

Align the bottom of the end plates with the bottom of theceiling joists.

Level the adjustable bars and, with a hammer, tap the nailscompletely into the joists to secure the adjustable bars inplace.

4

5

4

5

Type Adjustable HousingICwith LampLED

CAUTION RISK OF FIRE-

This product must be installed in accordance withthe applicable installation code by a person familiarwith the construction and operation of the productand the hazards involved.

Use minimum 90°c supply conductors.

G P I :ENERAL RODUCT NFORMATION

This product is suitable for indoor locations.

This product can be dimmed with a standard electronic dimmer.

This instruction shows a typical installation.

2

COLLAR

8

8

Adjust the collar position (horizontal position) by slidingthe housing on adjustable bars.

When the desired location is achieved, tighten the two #6self tapping screws to lock the housing onto the adjustablebars.

7

8

NOTE: See step 3 to align multiple housings

using the notches.

Carefully cut and remove the zip ties to remove theshipping plate.

6

1C

PRESSTOUNLOCKTILTZIP TIE

SHIPPING PLATE

HOUSINGADJUSTABLE BAR

7

COLLAR

NOTCH

1D

PRESSTOUNLOCKTILT

PR

ES

STO

UN

LOC

KTIL

T

3

Slightly loosen the wing nut to slide the butterfly bracketup or down.

After achieving the proper location, tighten the wing nutto secure the butterfly bracket in place.

Repeat steps 1 and 2 for the other butterfly bracket.

Utilize the butterfly brackets to install the housing inaccordance with local electrical codes.

BUTTERFLYBRACKET

COLLAR

WING NUT

1

2

NOTCH

Install the Housing with ButterflyBrackets

2A

1

2

3

4

NOTE: Skip this section if installing the housing

with adjustable bars.

3

NOTE: See step 3 to align multiple housings

using the notches.

PRESSTOUNLOCKTILT

3A 2x THUMB NUT

ADJUSTMENTNOTCH

Align Multiple Housings (Optional)

1

1

3

3

2

The alignment of the collars may be adjusted by reachinginto the housing and loosening the two thumb screws.Note: Adjustment of the lamp and heat sink may benecessary to access the thumb nuts. See Section 6

Rotate the collar (up to 45°) and align with other fixturesusing the notches in the collar with a laser or string.

Re-tighten the two thumb screws.

1

2

3

4

Connect Power to the Housing

Install the conduit to the housing electrical box.

Run the power line wires into the housing electrical box.

2

WARNING: RISK OF FIRE: When using the

housing electrical box for power feed through,

use 4 - #12 , or 6 - #14 branchMAX AWG AWG

circuit wires.

3

Push up on the tabs on the electrical box and remove theelectrical box cover.

1

4A

TABS

ELECTRICALBOX COVER

1

4B

3

2

5

Connect the neutral power line wire to the whitetransformer wire with a wire nut.

Connect the hot power line wire to the black thermalprotector wire with a wire nut.

Make sure that housing is grounded in accordance withlocal electrical codes.

For models with a 0-10V dimming driver, use the purpleand gray wire to connect to a compatible dimmer.

Replace the electrical box cover. Make sure that the topedge of the cover snaps under the tab.

Skip to section 5.

4

6

5

7

8

4C

For Citizen and Xicato see section 4CLED

For Lumenetix Warm Color Dimming see section 4DLED

For Lumenetix Programmable White see section 4ELED

4D

Connect the neutral power line wire to the whitetransformer wire with a wire nut.

Connect the hot power line wire to the black transformerwire with a wire nut.

Make sure that housing is grounded in accordance withlocal electrical codes.

For dimming, use the purple and gray wire to connect to acompatible dimmer.

Replace the electrical box cover. Make sure that the topedge of the cover snaps under the tab.

Skip to section 5.

10

12

11

13

14

15

13

11

12

10

75

46

Connect the neutral power line wire to the whitetransformer wire with a wire nut.

Connect the hot power line wire to the black transformerwire with a wire nut.

Make sure that housing is grounded in accordance withlocal electrical codes.

For dimming, use the purple and gray wires to connect to acompatible dimmer.

For white CCT (Color Control), use the blue and white wiresto connect to a compatible dimmer, see wiring diagram inSection 8.

For remote CCT (Color Control), hue, and saturation control,use the LCT handheld unit (Light Commissioning Tool soldseparately) and tie the blue and white wires together.

For DMX control wiring, use the following wires:

�Orange/White (DMX +)�Orange (DMX -)�Brown (Gnd)� Tie the Purple, Grey, and White wires together.

Replace the electrical box cover. Make sure that the topedge of the cover snaps under the tab.

16

18

17

19

20

21

22

4E

16

21

19

2121

18

20

17

9

6

CUT OUT

Insert the plaster ring completely into the collar/ceilingand secure them in place with the provided set screws andAllen wrench.

1

ROUND PLASTER RING SQUARE PLASTER RING

CUT OUT

NOTE: Longer set screws have been provided for

instances where the plaster ring does not reach the

collar and must be secured to the inside of the ceiling

cutout. Use the short set screws if the trim is installed in

the collar.

6A

PRESSTOUNLOCKTILT

PRESSTOUNLOCKTILT

PRESSTOUNLOCKTILT

SET SCREW

ALLENWRENCH

1

SHORT SET SCREW

TAB

TRIM HOLDER

LONG SET SCREW

TAB

CEILING

Install Drywall

5A

4-1/2"

ROUND COLLAR SQUARE COLLAR

For round trims, mark a 4-1/2" diameter circle on drywall.Cut out the marked section.For square trims, mark a 4-1/2" square on drywall. Cut outthe marked section.

1

4-1/2"

Align the cut out section of drywall with the collar andinstall drywall.

2

5B

2

DRYWALL COLLAR JOIST

PRESSTOUNLOCKTILT

PRESSTOUNLOCKTILT

Install Plaster Ring(For Flangeless Versions)

7

LE

NS

LO

CK

LE

NS

LO

CK

Plug the collar with the provided dust shield.

Properly plaster onto the plaster ring and drywall.

2

6C

Finish around the collar to match drywall.4

4 4

3

6B

LE

NS

LO

CK

PRESSTOUNLOCKTILT

PRESSTOUNLOCKTILT

22

PRESSTOUNLOCKTILT

Adjust the Lamp Position

BUCKETHANDLE

1

7A

BUCKETHANDLE

1 Push up the and heat sink to ensure that they are inLEDthe highest position.

LE

NS

LO

CK

PRESS TOUNLOCK TILT

7B

2TILT ADJUSTMENTLEVER

INDICATOR

2

010

203040

o

o

o

oo

2 For proper wall wash positioning, unlock the tiltadjustment lever by pressing where indicated using afinger or screwdriver to tilt until 15° angle is reached.

PRESSTOUNLOCKTILT

7C

ROTATION LOCK 3

4

NOTE: Lamp housing can rotate 361° horizontally.

3 Pull the rotation lock down to unlock the lamp housing.

Rotate the lamp housing horizontally.When the desiredposition is achieved push the rotation lock up to lock thelamp housing in place.

4

8

Wiring Diagrams for Lumenetix LED

8AE

lem

en

t4"

LE

D–

Lu

men

eti

x–

Warm

Dim

&P

rog

ram

mab

le W

hit

e

for

sin

gle

0-1

0v

Dim

me

r

Exte

rna

l H

ot

-Bla

ck

Exte

rna

l C

om

mo

n

-W

hite

Vio

let

Wire

0-1

0v D

imm

ing

Gre

y W

ire

Com

mon

White W

ire

Blu

e W

ire

Red W

ire

-Positiv

e12v

Blu

e W

ire

-Negative

12v

Blu

e W

ire

-Ne

ga

tive

12

v

Blu

e W

ire

-Negative

12v

L.T.F

Dimmable LED D r i v e r

255LEDD*20W12V

Exte

rna

l G

rou

nd

-G

ree

nG

rou

nd

pro

vid

ed

in e

ach

ho

usin

g

-

+V

iole

t

Wire

Gre

y

Wire

Sw

itched

hot

L.T.F

Dimmable LED D r i v e r

255LEDD*20W12V

L.T.F

Dimmable LED D r i v e r

255LEDD*20W12V

DM

X C

ontr

ol Lin

es

Org

/Wht

=D

MX

+

Ora

nge

=D

MX

-

Bro

wn

=S

ign G

nd

Red W

ire

-Positiv

e12v

Re

d W

ire

-Po

sitiv

e1

2v

DM

X C

on

tro

l L

ine

s

Org

/Wh

t=

DM

X+

Ora

ng

e=

DM

X-

Bro

wn

=S

ign

Gn

d

DM

X C

on

tro

l L

ine

s

Org

/Wh

t=

DM

X+

Ora

ng

e=

DM

X-

Bro

wn

=S

ign

Gn

d

Wh

ite

Wire

Blu

e W

ire

White W

ire

Blu

e W

ire

9

8B4

10

Notes

11

Notes

12

SAVE THESE INSTRUCTIONS!

7400 Linder Ave, Skokie, 60077IL

847.410.4400

www.element-lighting.com© 2016 Tech Lighting, L.L.C. All rights reserved.The "Element" graphicis a registered trademark of Element. Element reserves the right tochange specifications for product improvements without notification.

A Generation Brands Company