1

Installation Instructions

for the Rolltec®

Adalia X3M™ Awning

Hammer drill

Masonry bit set

Drill bit 3/16” (for 3/8” lag bolts) or 1/4” (for 1/2” lag bolts)

if mounting on surface that requires pilot holes

3/4” wrench-and-ratchet set (for slope adjustment)

13mm socket (for securing square bar in mounting brackets)

3/16” Allen key (for slope adjustment) and 5mm Allen key

(for hood brackets)

Phillips driver #2 (for hood end plates)

Ladders

Level

Chalk line

When mounting a retractable awning, it is extremely important to take into consideration the

type of building surface you will be installing on. Whether the building’s exterior is stucco, sid-

ing or brick, it is imperative to install the mounting brackets in a correct manner, to properly

secure the awning to the building’s surface.

A retractable fabric awning is designed to provide shade and light rain protection*, and should

be retracted during heavy rain, snow, or severe wind conditions.

* A Minimum of 15° slope is required, and should be used under proper care.

Supplied: Installation wall

brackets. Other brackets

available upon request.

Not Supplied: Anchors, lag

bolts, or mounting screws

for installation. We recom-

mend 3/8” lag bolts with

washers and corresponding

anchors.

Questions? Call Rolltec®

at 1-800-667-0474

Available installation brackets

Side dimensions of various installations

Determining installation height and coverage

Positioning installation brackets

Mounting wall brackets to surface

Attaching and operating the awning

Installation of the protective hood (optional)

Slope adjustment instructions

2

3

4

5

6

7

8

9

Table of Contents

General Tool Requirements

Notes

2

Wall Bracket

Extruded aluminum with a powder coated finish. For

flat surface mounting, such as brick, wood, or siding.

Ceiling Bracket (optional)

To be used for installations under the soffit. Can be

used individually or in combination with rafter brackets.

Roof Bracket Roof brackets are made of stainless steel and used in

combination with a wall bracket when installing on a

roofline.

Roof brackets can be adjusted between 10° and 90° to

accommodate the slope of the roof.

Rafter Bracket (used in combination with ceiling brackets, optional)

Rafter brackets are made of steel with a white powder coated finish. They are available

in 4 sizes, and must be used in combination with a ceiling bracket.

Available Installation

Brackets for the Adalia X3M™

3

Side Dimensions for Various Installations

The angle of the roof brackets is

adjusted between 10° and 90° to

ensure that the awning is mounted

upright despite the slope of the

roof. A protective hood is recom-

mended.

Installation under overhang

Installation on wall with

optional protective hood

Installation under overhang

with rafter brackets

Installation on wall

When mounting under a

soffit, make sure that the

back edge of the ceiling

bracket is at least 11” from

the front edge of the roof.

This protects the retracted

awning from weather ele-

ments.

Bolt only 3 holes (2 holes if

trusses are 2x4) of the raf-

ter bracket to the center of

the roof truss, the wood

might crack if all 4 holes are

bolted.

Installation on roof

with protective cover

4

Determining Installation Height and Coverage

The horizontal coverage of an awning is

determined by the length of the arms

and the angle of the awning. Arms come

in several standard sizes, and the angle

can be adjusted.

Tables for Various Arm Sizes and Angles

5° 10° 15° 20°

5’4” 1’ 1” 1’ 7” 2’ 0” 2’ 5”

6’9” 1’ 2” 1’ 9” 2’ 4” 2’11”

8’8” 1’ 4” 2’ 1” 2’10” 3’ 7”

10’0” 1’ 5” 2’ 4” 3’ 2” 4’ 0”

11’8” 1’ 7” 2’ 7” 3’ 7” 4’ 7”

Angle

Arm

Siz

e

Vertical

Drop

5° 10° 15° 20°

5’4” 5’ 4” 5’ 3” 5’ 2” 5’0”

6’9” 6’ 8” 6’ 7” 6’ 6” 6’ 4”

8’8” 8’ 7” 8’ 6” 8’ 4” 8’ 2”

10’0” 9’11” 9’10” 9’ 8” 9’ 5”

11’8” 11’ 6” 11’ 5” 11’ 3” 11’0”

Arm

Siz

e

Angle Horizontal

Coverage

NOTE: In order to use an awning for light rain pro-

tection, it must be installed with a 15° slope or greater.

Brackets in Relation to Awning Width

7’-10’ 11’-13’ 14’-15’ 16’-18’ 19’-23’ 24’

5’4”-10’0” 2 3 3 4 5 6

11’8” n/a n/a 4 4 5 6

Number of

Installation

Brackets

Awning Width

Arm

Size

Awnings wider than

20’ require 3 arms.

5° 10° 15° 20°

5’4” 8’ 1” 8’ 7” 9’ 0” 9’ 5”

6’9” 8’ 2” 8’ 9” 9’ 4” 9’ 11”

8’8” 8’ 4” 9’ 1” 9’10” 10’ 7”

10’0” 8’ 5” 9’ 4” 10’ 2” 11’ 0”

11’8” 8’ 7” 9’ 7” 10’ 7” 11’ 7”

Arm

Siz

e

Angle Suggested

Installation

Height

NOTE: The table of suggested installation heights uses 7’ of headroom below the front val-

ance. To calculate the installation height for a different amount of headroom, use the table of

vertical drops and add to your preferred headroom:

INSTALLATION HEIGHT = HEADROOM + VERTICAL DROP

5

Positioning Installation Brackets

Refer to these illustrations when

determining the positions of installa-

tion brackets. See the next page for

step-by-step installation instructions.

Brackets that are placed on

the outside of the arm

shoulder (bracket 1 and 2

in all the illustrations)

should be as close to the

arm shoulder as possible,

up to 12”.

Brackets placed inside the

arm shoulder (bracket 3 or

4 in Fig.2) should be 12” to

24” from the arm shoul-

der.

Fig.1: Awning with 2 Arms and 2 or 3 Brackets

It is important to properly secure the installation brackets to the surface. The weight of the

awning, added pulling forces and aerodynamic lifts (when the awning is extended) are creating

considerable stress on the installation brackets.

Expected stress values are factored into the number of brackets shipped with an awning.

However, it is assumed that the awning will be installed on a solid surface. When installing on

a weaker surface, it is recommended to use additional brackets to spread the load. Extra

brackets are available on request, for a small added charge.

Fig.2: Awning with 2 Arms and 4 or 5 Brackets

Fig.3: Awning with 3 Arms and 5 Brackets

Fig.5: Awning with 4 Arms and 8 brackets

Fig.4: Awning with 3 Arms and 6 Brackets

NOTE 1: There should be

a bracket on the outside of

the shoulder whenever

possible! If not, place

bracket inside as close to

the arm shoulder as possi-

ble.

NOTE 2: Wider awnings

come with a fabric centre

support. It should be taken

into consideration when

positioning the brackets.

6

Mounting Wall Brackets to Surface

Chalk a horizontal line at the optimum installation height

(as determined on page 4). The level of the line corre-

sponds to the level of the bottom installation screw. This

step is not necessary if installing on brick.

Align a wall bracket so that the chalk line goes through

the middle of the bottom hole (A). If installing on brick,

make sure that both holes are on brick and not mortar

(fastening an awning to mortar will cause it to loosen

over time).

Use a level to make sure that the bracket is upright (B).

Use a pencil to draw a line down the middle of the

small visible wall area through the bottom hole. Keep-

ing the bracket in place, draw a pair of perpendicular

lines that intersect in the centre of the top hole. C il-

lustrates the resulting marks.

After marking the locations of drill holes for the two out-

side brackets, drill the holes and attach them loosely.

NOTE: If a protective hood is to be used, the hood brack-

ets should be installed together with the wall brackets (D).

Step 4. Align and Attach Remaining Brackets

Align the remaining wall brackets with respect to the two outside ones. They will need to be

able to fit and support installation bar, and good alignment is important.

Once you are satisfied with the align-

ment, tighten all screws firmly and

check that each bracket is attached

solidly to the surface.

NOTE: Check to see that the wall is flat and even. If it is not, it is advisable to mount the

brackets on a cedar wooden board first. The brackets can be attached to the board with car-

riage bolts, before the board is mounted on the wall. Use a 2”x8” board; if the awning has a

protective hood use a 2”x10”.

Step 1. Draw a Horizontal Line

Step 2. Mark Where to Drill Holes

Step 3. Drill Holes and Attach Outside Brackets

D

7

Attaching and Operating the Awning

Attaching the Awning

Extending and Retracting the Awning

Manual Operation

Start by attaching the crank by hooking it through

the loop in the gear mechanism, as shown.

For a right side crank (pictured), turning the

crank counter-clockwise will extend the awning,

and turning clockwise will retract it. For a left

side crank, it’s the other way around.

You will know that the awning has fully extended

once the fabric becomes slightly slack. When this

happens, turn the crank in the opposite direction

just enough for the fabric to go back to being

taut.

1. Make sure that both your hands and the work-

ing area are clean.

2. Remove the awning from the protective sleeve.

Do not use a knife, as you risk damaging the

fabric.

3. Slide awning square bar into the mounted brack-

ets. Use a 13mm socket and the supplied bolts

to secure the square bar inside the brackets.

The procedure is identical for both wall and ceiling

installations.

Motorized Operation

Use the supplied electrical 3-way control (switch or remote) to operate your awning. The UP

button is to close the awning, and the DOWN button is to open the awning. The middle but-

ton lets you stop the awning partway. If you adjust the slope, you might have to adjust the

limit switches on your motor. Also, resetting the limit switches on your motor is recom-

mended after the first few months of use, as awning fabric has a tendency to stretch. Please

refer to instructions supplied with the motor or contact Rolltec®.

When retracting from a fully extended position, the first turn or two can offer a fair amount

of physical resistance. This is normal and should not cause alarm.

8

Installation of the Protective Hood (Optional)

The hood is manufac-

tured in two pieces: a

female part, and a male

part. The female part

holds a PVC weather

strip. This strip goes

against the wall, eliminat-

ing the need for caulking.

The two parts joined as shown, and hold together mainly with gravity. The three small

grooves in the hood are screw holes, and are used in attaching side cover plates. The remain-

ing two grooves (which are significantly larger), are used to fit the hood onto hood brackets.

Hood brackets are usually installed at the same time as wall brackets (see page 6, Fig.D), but

can be added later. Remember that hood brackets must go in front of the wall brackets, but

behind the washers of the screws securing the brackets to the wall.

NOTE: A protective hood is optional, but it comes very highly recommended when the awn-

ing is installed on a flat, exposed surface. If the awning is equipped with an electric motor and

there is no overhang shielding the awning from the elements, a hood is mandatory. A hood

cannot be used in conjunction with ceiling brackets.

Fitting a Hood onto Hood Brackets

Each hood bracket comes with two

tongues that fit into the large grooves

on the underside of the protective

hood. The hood is slid on after the

brackets have been installed.

Afterwards, the screw shown in the

picture on the left should be tightened.

NOTE: A protective hood can be in-

stalled before or after mounting the

awning onto the wall brackets.

Structure of a Protective Hood

9

Slope Adjustment Instructions

You will need a 3/16” Allen key and a 3/4” wrench-and-ratchet set to perform the

adjustment procedure.

Before starting, extend the awning fully.

Note that slope adjustment is done on one arm at a time, the arms should not differ

in slope by more than 10° (you need to go back and forth between arms if you want

a steeper adjustment), and the final slope of each arm must be equal.

You should support the arm being adjusted.

1. Locate two side bolts on the arm shoulder.

2. Remove the plastic end caps (see A) covering

both bolts and nuts.

3. Using a 3/4” wrench and ratchet, loosen (but do

not remove: max. 1.5 turns!) both bolts (see B).

4. Before turning the adjustment screw, lift the arm

from the bottom to alleviate the pressure from

the arm shoulder.

5. Use a 3/16” Allen key to turn the adjustment

screw (see C), located on the bottom of the arm

shoulder. Turning clockwise raises the angle, while

turning counter-clockwise lowers it.

6. Once the arm is at the desired slope, retighten

the bolts and replace the plastic end caps back on.

Preparation

Procedure (for each arm)