LED STRIPE®Installation InstructionsManual Instalación
INDEX ÍNDICE
REFERENCES / REFERENCIAS 4
TECHNICAL DATA / DATOS TÉCNICOS 4
MEASURES / MEDIDAS 5
INSTALLATION / INSTALACIÓN 5
CONNECTION / CONEXIONADO 6SAFETY PRECAUTIONS / PRECAUCIONES 8
LS.IMT-132.v2.4.
Led
Strip
e®
TEC
HN
ICA
L G
UID
E
LED STRIPE®REFERENCES REFERENCIAS
710400 1 /C02
Color Color
/C02 Cool white Blanco frio/C27 Neutral white Blanco neutro/C22 Warm white Blanco cálido/C04 Amber Ambar/C03 Red Rojo/C09 Blue Azul
Length Longitud
1 - 250 mm2 - 500 mm3 - 750 mm4 - 1000 mm
LED STRIPE®TECHNICAL DATA DATOS TÉCNICOS
MECHANICAL SPECIFICATIONS ESPECIFICACIONES MECÁNICAS
Measures Medidas 13 x 38 x 1000 mm 13 x 38 x 750 mm 13 x 38 x 500 mm 13 x 38 x 250 mm
Weight Peso 591 gr 450 gr 347 gr 198 gr
Housing Cuerpo Aluminum
Protection class Grado de protección IP66
ELECTRICAL SPECIFICATIONS ESPECIFICACIONES ELÉCTRICAS
Input voltage Voltaje de entrada 24V DC
Protection class Clase de protección III
Control type Tipo de control Dimmable
LED LED 120 LEDs/m
Power consumption Potencia 11,6 W (Whites and Blue) - 5,8W (Amber and Red)
LS.IMT-132.v2.5.
Led
Strip
e®
TEC
HN
ICA
L G
UID
E
LED STRIPE® MEASURES MEDIDAS
250 mm / 500 mm / 750 mm / 1000 mm (9.8 in / 19.7 in / 29.5 in / 39.4 in)
13 mm (0.51 in)
15 mm (0.59 in)
41,3 mm (1.68 in)
LED STRIPE®INSTALLATION INSTALACIÓN
CLICK!
LS.IMT-132.v2.6.
Led
Strip
e®
TEC
HN
ICA
L G
UID
E
LED STRIPE®CONNECTION CONEXIONADO
Power Supply
24 V DC - 320WFuente
Alimentación
Power Supply
24 V DC - 320WFuente
Alimentación
Linear Drive
Ref.M030368
LED Stripe ® ® ® LED Stripe LED Stripe
Ref.
M030360
Ref. M030226
Ref. M030154
Ref.M030369
End cap
Tapón final
Maximum 10 LED Stripe® 1000 mm per line. Maximum 2 lines in parellel connection (20 LED Stripe® 1000 mm) connected to Lineardrive 720 (PSU 24 V DC - 320W). Maximum 5 m from the power supply to the first LED Stripe® . Máximo 10 LED Stripe® 1000 mm por línea. Máximo 2 líneas en paralelo (20 LED Stripe® 1000 mm), conectadas a Lineardrive 720 (fuente de alimentación de 24 V DC - 320W). Máximo 5 m. desde la fuente de alimentación al primer LED Stripe ® .
Maximum 20 LED Stripe® 1000 mm per line. Maximum 2 lines in parellel connection (40 LED Stripe® 1000 mm) connected to Lineardrive 720 (PSU 24 V DC - 320W). Maximum 5 m from the power supply to the first LED Stripe® . Máximo 20 LED Stripe® 1000 mm por línea. Máximo 2 líneas en paralelo (40 LED Stripe® 1000 mm), conectadas a Lineardrive 720 (fuente de alimentación de 24 V DC - 320W). Máximo 5 m desde la fuente de alimentación al primer LED Stripe ® .
Maximum 10 LED Stripe ® 1000 mm per line. Maximum 2 lines in parellel connection (20 LED Stripe ® 1000 mm)connected to PSU 24 V DC - 320W. Maximum 5 m from the power supply to the first LED Stripe .®
Máximo 10 LED Stripe ® 1000 mm por línea. Máximo 2 líneas en paralelo (20 LED Stripe ® 1000 mm), conectadas a fuente de alimentación de 24 V DC - 320W. Máximo 5 m desde la fuente de alimentación al primer LED Stripe® .
Maximum 20 LED Stripe® 1000 mm per line. Maximum 2 lines in parellel connection (40 LED Stripe® 1000 mm) connected to PSU 24 V DC - 320W. Maximum 5 m from the power supply to the first LED Stripe® . Máximo 20 LED Stripe® 1000 mm por línea. Máximo 2 líneas en paralelo (40 LED Stripe ® 1000 mm), conectadas a fuente de alimentación de 24 V DC - 320W. Máximo 5 m desde la fuente de alimentación al primer LED Stripe® .
11,6 W/m
5,8 W/m
11,6 W/m
5,8 W/m
LS.IMT-132.v2.7.
Led
Strip
e®
TEC
HN
ICA
L G
UID
E
24V DC-PWM (Azul Blue)
GND- (Negro Black)24+ (Blanco White)24+ (Marrón Brown)
+
LINEARdrive 720D
Group 1GND 1
GND 2
GND 3
GND 4
DMX +
+-
DMX -DMX shieldLEDSync +
Dali INDali INDali OUTDali OUT
LEDSync -LEDSync shield
Group 2
Group 3
Group 4
M050206Power Supply24 V DC 320 W
+ +- -
230V AC
Power Supply24 V DC 320 W
+-
24V DC
PWM (Azul Blue)GND- (Negro Black)24+ (Blanco White)24+ (Marrón Brown)
-
+
24V DC-PWM (Azul Blue)
GND- (Negro Black)24+ (Blanco White)24+ (Marrón Brown)
+
LINEARdrive 720D
Group 1GND 1
GND 2
GND 3
GND 4
DMX +
+-
DMX -DMX shieldLEDSync +
Dali INDali INDali OUTDali OUT
LEDSync -LEDSync shield
Group 2
Group 3
Group 4
M050206Power Supply24 V DC 320 W
+ +- -
230V AC
Power Supply24 V DC 320 W
+-
24V DC
PWM (Azul Blue)GND- (Negro Black)24+ (Blanco White)24+ (Marrón Brown)
-
+
Lineardrive 720D DMX/DALI/0-10V 24V DC
Steady light Luz fija
LED STRIPE®WIRING DIAGRAM DIAGRAMA CONEXIÓN
LS.IMT-132.v2.8.
Led
Strip
e®
TEC
HN
ICA
L G
UID
E
Use as directed
This product serves exclusively lighting purposes and may:• Expose to strong mechanical loads or strong contamination.• Only be installed and operated after a condition inspection if the product is dirty or has been moistened through storage.• Not be modified or converted.
If these points named above are not adhered to, a short circuit or electrical shock may occur!
InstallationThe complete installation must be done by an electrical expert or a specialized maintenance team, who is familiar with valid directives.
Attention: Switch off power of the mains supply or respectively of the connection lead before doing any works.
Use only parts, which are supplied with the product or are described as accessories! Otherwise the product or the installation might not be sufficiently safe!
Indication for the installer: In case you do not install a completely supplied system (with transformer), you are considered a “manufacturer” by the low-voltage directive. In this case you are required to ensure the conformity of the whole system and declare it by attaching the CE-sign.
Installation placeMake sure that the product is mounted on a stable, even and tilt-fixed backgSQUARE. Note the minimum distances in the ceiling.
Attention: Do not cover the product, especially not with insulating materials.
Operation - Information for the userOperate the product only if it is working correctly. Switch off the product with a malfunction immediately and operate it again only after examination by an electrical specialist. This is the case, when:• Visible damages appear.• The product does not work.• Smoke, steam or crackling sounds appear.• An overheating is recognisable.Repairs of the product or work on mains voltage-prominent sections may only be carried out by qualified electricians.
Attention: Exists mortal danger from an electric shock!
How to avoid failure and fire risk• Do not cover the product - provide free air circulation!• Do not hang or fasten anything on the product, especially no decoration.• Never let children play unsupervised with electric products!• Children can not always estimate dangers in dealing with electric energy correctly.
Disconnect the product from power, before you…• Clean or maintain the product.• Do any works on the product or its components (electric expert).
LED STRIPE®SAFETY PRECAUTIONS PRECAUCIONES
LS.IMT-132.v2.9.
Led
Strip
e®
TEC
HN
ICA
L G
UID
E
Empleo según normativas
Este producto sirve únicamente para iluminación y no debe:• Exponerse a exigencias mecánicas excesivas o fuertes suciedades.• Después de un almacenamiento húmedo o contaminante, no utilizar sin previa verificación.• No debe ser cambiado o modificado.
En caso de no respetarse los puntos previamente señalados, podrá producirse un cortocircuito o una descarga eléctrica.
MontajeLa instalación completa puede llevarse a cabo por un electricista especializado o un servicio de asistencia técnica especializado que conozca de las directivas vigentes.
Atención: Desconecte la línea de alimentación antes de realizar cualquier trabajo.
Utilice exclusivamente piezas que fueran suministradas con el producto o que son descritas definitivamente como accesorios. De lo contrario, el producto puede no ser suficientemente seguro.
Advertencia para el electricista: Si no instala un sistema suministrado de forma completa (es decir con el transformador), actuará como el “fabricante“ en el sentido de las directivas de baja tensión. En este caso le incumbe a usted establecer la conformidad del sistema completo y declararla mediante la aplicación de la marca CE.
Lugar de montajePreste atención a que el producto sea montado sobre una base firme, plana y estable. ¡Tenga en cuenta las distancias mínimas en el techo!
Atención: No tape el producto, en especial, con material aislante.
Funcionamiento - Información para el usuarioUtilice el producto únicamente si funciona de forma perfecta. En caso de fallo, desconecte inmediatamente el aparato y vuelva a utilizarlo sólo tras una revisión por parte de un electricista. Esto es el caso por ejemplo de cuando:• Aparecen daños visibles.• El producto no funciona perfectamente.• Se desprende humo, vapor o en caso de saltar chispas.• Es reconocible un sobrecalentamiento.Todas las reparaciones y/o trabajos en partes conectadas deben ser realizadas únicamente por electricistas especializados.
Atención: De lo contrario, puede haber peligro de muerte por descarga eléctrica.
Consejos para evitar averías e incendios• No cubra el producto, no obstruya la circulación de aire.• No cuelgue ni fije nada en el producto, especialmente ningún tipo de decoración.• No permita que los niños jueguen sin vigilancia con los productos eléctricos. Los niños no son siempre conscientes del peligro de la energía eléctrica.
Desconecte en primer lugar el producto antes de...• Llevar a cabo trabajos de limpieza y cuidado.• Realizar trabajos en el producto o en sus componentes (sólo electricistas).
LED STRIPE®SAFETY PRECAUTIONS PRECAUCIONES
LS.IMT-132.v2.10.
Led
Strip
e®
TEC
HN
ICA
L G
UID
E
NOTAS NOTES
LS.IMT-132.v2.11.
Led
Strip
e®
TEC
HN
ICA
L G
UID
E
NOTAS NOTES
CENTRAL Y FÁBRICA / HEADQUARTERS BARCELONA C/ dels Oficis, 25. Polígono el Regàs. 08850 Gavà (BARCELONA) SPAIN Tel. (+34) 93 630 28 00 Fax. (+34) 93 630 29 66 e-mail. [email protected]
IMT-132 v.02
Led Stripe®