Installation Instructions Roll Stand · Philips IntelliVue Shelf w/ 30° tilt limit 2 6" (152 mm)...

Installation Instructions

Roll Stand

w w w . a m i c o . c o m

1 Amico Accessories Inc.

Important, Please Read Carefully

Thank you for your purchase with Amico.

The Amico Roll Stand is designed for long lasting performance, providing the user complies with assembly and maintenance procedures. This instruction manual is your guide to ensuring that you get the best performance out your new equipment. Amico Accessories is not responsible for any damage as a result of (but not limited to) abuse and other malfunctions that may be a direct or indirect result of failure to comply with the instructions provided in this manual.

Please note these key words and symbols:

WARNING Steps where extra care should be taken to prevent injuries and damage

NOTE Steps that point out helpful information

RESPONSIBILITY OF MEDICAL FACILITIES

Preventive maintenance checks must be performed regularly to maintain the quality and performance of this product. Any parts that may be broken, missing, worn, distorted or contaminated in any way should not be used and all affected parts should be replaced immediately. Should the necessity of any repair be suspected; please contact your local Amico distributor.

Preface

www.amico.com 2

Table of Contents

Section 1: Product SpecificationsFeatures 3Production Classification 3-4

Section 2: Installation PreparationInstallation Tools Requirements 5-6Parts Legend 7

Section 3: Roll Stand AssemblyRoll Stand Counterweight Assembly 8Roll Stand Base Assembly 9Roll Stand Head Assembly 10Roll Stand Handle Assembly 11Roll Stand Basket Assembly 12

Section 4: Device InstallationMonitor Shelf: 3" (76.2 mm) Bottom/Back Mount, 5" (127 mm) Bottom/Back Mount and VESA Quick Release 14Monitor Shelf: 6" (152.4 mm) Drop-On 15Monitor Shelf: Philips IntelliVue 16Monitor Shelf: Welch Allyn 16Monitor Shelf: VESA 17Accessory Shelf: Disc 18

Section 5: AdjustmentsMonitor Tilt 19Heavy Duty Head Tilt 19

Section 6: Maintenance, Troubleshooting and CleaningTroubleshooting Guide 20Preventative Maintenance 21Cleaning 21

Warranty Information 22


Features

1. -PKG models offer a storage basket and handle for transport ease

2. Overall height: 42" (106.7 cm)

3. Sturdy base height: 24" (60.1 cm)

4. Locking casters: 3" (7.6 cm)

Section 1: Product Specifications

Product Classification

NOTE: There are various available weight ratings for different clinical applications. These weight ratings reference a typical configuration of the roll stand. Please note your particular model and mounting specification using the charts below:

BACK/BOTTOM MOUNT

3Philips IntelliVue Shelf

w/ 30° tilt limit

26" (152 mm)

Drop on shelf

RS_-42_/LCD-PKG (fill in blank with desired option)

6

7

5

Base counterweightmax. 20 lbs (9.07 kg)

Base and leg counterweight

max. 25 lbs (11.33 kg)

No counterweightmax. 5 lbs (2.26 kg)

05" (127 mm) Shelf

w/ 30° tilt limit

4Accessory add

on top5" (127 mm) Shelf for

back mounts

6 75" (127 mm) Shelf w/slide-in VESA 75/100

Plate

8 3" (76 mm) Shelf

w/30° tilt limit

9 3" (76 mm) Shelf for

back mounts

W Welch Allyn w/30° tilt

limit

*Weight ratings include 10 lbs in basket*Highlight denotes counterweight placement

44.

801

27

.855

9.000FROM CENTRE

OF POST

42.

380

7.083FROM CENTRE

OF POST

RS_-___-___ Project #: 0378

UNLESS SPECIFIED ALL DIMENSIONS IN INCHESBREAK ALL EDGES .005 - .010ANGLE TOLERANCES 1FRACTIONAL TOLERANCES 1/32DECIMAL TOLERANCES: .XX .03 .XXX .005 .XXXX .0005

5 4 3 2 1

DESCRIPTION:

PART NO:

SCALE: DRAWN BY:

CHECKED BY:

SHT. OF

DRAWING NO:NTS 1 1

PRIVATE AND CONFIDENTIALTHIS PRINT IS PROPERTY OF AMICO ACCESSORIES AND IS LOANED IN CONFIDENCE SUBJECT TO RETURN UPON REQUEST AND WITH THE UNDERSTANDING THAT NO COPIES ARE TO BE MADE WITHOUT THE CONSENT OF AMICO ACCESSORIES

ALL RIGHTS TO DESIGN OR INVENTION ARE RESERVEDDATE:DATE:

CADBLOCK for RS_-___-___

EC 2014-03-26JT AUG 15/14

85 Fulton WayRichmond Hill, OntarioL4B 2N4, CanadaToll Free: 1.877.264.2697 (T)Tel: (905) 763.7778Fax: (905) 763.8587

CADBLOCK for RS_-___-___RS_-___-___

20140326-E2849

PROJECTION

44.

801

27

.855

9.000FROM CENTRE

OF POST

42.

380

7.083FROM CENTRE

OF POST

RS_-___-___ Project #: 0378


5 4 3 2 1

DESCRIPTION:

PART NO:

SCALE: DRAWN BY:

CHECKED BY:

SHT. OF

DRAWING NO:NTS 1 1




EC 2014-03-26JT AUG 15/14



20140326-E2849

PROJECTION

44.

801

27

.855

9.000FROM CENTRE

OF POST

42.

380

7.083FROM CENTRE

OF POST

RS_-___-___ Project #: 0378


5 4 3 2 1

DESCRIPTION:

PART NO:

SCALE: DRAWN BY:

CHECKED BY:

SHT. OF

DRAWING NO:NTS 1 1




EC 2014-03-26JT AUG 15/14



20140326-E2849

PROJECTION

www.amico.com 4

BACK/BOTTOM MOUNT

3Philips IntelliVue Shelf

w/ 30° tilt limit

26" (152 mm)

Drop on shelf

RS_-42_/LCD (fill in blank with desired option)

6

7

5

Base counterweightmax. 25 lbs (11.33 kg)

Base and leg counterweight

max. 30 lbs (13.60 kg)

No counterweightmax. 10 lbs (4.53 kg)

05" (127 mm) Shelf

w/ 30° tilt limit

4Accessory add

on top

5" (127 mm) Shelf for back mounts

6 75" (127 mm) Shelf w/slide-in VESA 75/100

Plate

8 3" (76 mm) Shelf

w/30° tilt limit

9 3" (76 mm) Shelf for

back mounts

W Welch Allyn w/30° tilt

limit

Product Classification

Section 1: Product Specifications

*Highlight denotes counterweight placement


Installation Tool Requirements

NOTE: Please ensure that your contents match the list as outlined below. If not, please contact Amico Accessories at 1-877-264-2697.

WARNING: IT IS THE INSTALLER’S RESPONSIBILITY TO ENSURE ALL COMPONENTS ARE PROPERLY ASSEMBLED AND INSTALLED USING THE PROVIDED INSTRUCTION MANUAL.

WARNING: EXCEEDING WEIGHT CAPACITIES CAN RESULT IN SEVERE PERSONAL INJURY OR DAMAGE TO YOUR EQUIPMENT. IT IS THE INSTALLER’S RESPONSIBILITY TO ENSURE THE COMBINED WEIGHT OF ALL COMPONENTS DOES NOT EXCEED THE WEIGHT CAPACITY LISTED IN PRODUCT CLASSIFICATION ON PAGE 3 AND 4 OF THIS MANUAL.

WARNING: DO NOT PLACE ANY MODELS ON AN INCLINE GREATER THAN 10 DEGREES OR UNIT MAY TIP.

WARNING: ALWAYS USE LOCKS ON CASTERS WHEN EQUIPMENT IS NOT IN USE TO PREVENT UNWANTED MOVEMENT. THE LIST BELOW INCLUDES ALL PARTS REQUIRED FOR INSTALLATION. PLEASE CHECK THE CONTENTS OF YOUR PACKAGE TO ENSURE ALL PARTS ARE INCLUDED. IF ANY HARDWARE OR PARTS ARE MISSING, PLEASE CONTACT AMICO ACCESSORIES.

Section 2: Installation Preparation

A: Tools

1 5

2 6

3 7

4

1. 3/16" (47.6 mm) hex key – not included

2. Phillips #2 and #3 screwdriver – not included

3. ½" (1.27 cm) socket wrench – not included

4. ½" (1.27 cm) multi-tool socket drive - included

5. 4 mm hex key (0.4 cm) – not included

6. 12 mm hex key (1.2 cm) – not included

7. ¼" hex key (6.35 mm) – not included

www.amico.com 6

Installation Tool Requirements

The picture below shows box contents. Please note the picture is for reference only. Content or layout may vary depending on model selection. RS6/7 models include a counterweight package and additional hardware kit for counterweight installation.

Basket (PKG only )(Brown Box)

Roll Stand Base Handle Package (PKG only)

Monitor Head (PM5 shelf shown) (Left), Hardware Kit 2

Roll Stand Casters and Hardware Kit 1

Roll Stand Post Counterweight and Counterweight Hardware

(RS6 and RS7 only)

Roll Stand Post

Roll Stand Handle Package

Roll Stand Base

Basket

Monitor Head and Head Hardware Kit

Casters and Post Hardware Kit



Parts Legend

NOTE: Please note part descriptions provided below.


Manufacturer Part Number Part DescriptionRS#-42#-PKG/RS#-42#-LCD ROLL STAND MODEL NUMBER

X-RS-BASE STAND BASE

X-RS-BCW BASE COUNTERWEIGHT

X-RS-CW-BASE BASE LEG COUNTERWEIGHTS

H-THPMS-832-516 BASE COUNTERWEIGHT SCREWS

H-FHMS-1420-34 BASE LEG COUNTERWEIGHT SCREWS

H-CWSH-10 BASE COUNTERWEIGHT “C” WASHERS

X-RS-CSTR-3B CASTERS

X-RS-POST STAND POST

RS-ADA-125 POST ADAPTER/BASE ADAPTER

H-HSCS-51618-312 POST-HW KIT LARGE BOLT

H-RS-LOCK-WASH POST-HW KIT LOCK WASHER

H-STW-516-SMOD POST-HW KIT SMALL WASHER

H-SCS-51618-35 HEAD-HW KIT LARGE BOLT

H-BZ-WASH-516-34 HEAD HW-KIT BRONZE WASHER

H-NYL-WSH-516 HEAD HW-KIT NYLON WASHER

X-MON-HEAD MONITOR HEAD

X-MON-BUSH-SM PLASTIC BUSHING

X-DOME-CIR-LBL AMICO STICKER

RS1-HANDLE ROLL STAND HANDLE

X-PC-125-1-8-32 BASKET POLE CLAMP FRONT HALF

X-PC-125-2-8-32 BASKET POLE CLAMP BACK HALF

H-HSCS-1420-34 REAR BASKET SCREWS (BLACK)

H-PHMS-1032-916 HANDLE KIT SCREWS

Sold separately. Please call. ACCESSORY SHELF

Sold separately. Please call. KEYBOARD TRAY

Sold separately. Please call. HEX FLAT HEAD SCREWS

www.amico.com 8

Section 3: Roll Stand Assembly

Roll Stand Counterweight Assembly

NOTE: Perform step 1 and/or step 2 only if model includes counterweights. If not, please proceed to next page.

1. (Optional) For RS6/7 models, place the top of the STAND BASE into the bottom opening of the BASE COUNTERWEIGHT. Secure by inserting and tightening the five BASE COUNTERWEIGHT SCREWS through the five BASE COUNTERWEIGHT “C” CLIPPED WASHERS and into the BASE COUNTERWEIGHT screw holes using Phillips #2 head screwdriver (Figure 1).

2. (Optional) For RS7 models with BASE LEG COUNTERWEIGHTS, insert and tighten the ten BASE LEG COUNTERWEIGHT SCREWS through the BASE LEG COUNTERWEIGHTS and into the STAND BASE using Phillips #3 head screwdriver (Figure 2).

(Figure 1) (Figure 2)

BASE LEG COUNTERWEIGHT SCREWS[H-FHMS-1420-34]

10X

BASE LEG COUNTERWEIGHTS[X-RS-CW-BASE]

5X

STAND BASE[X-RS-BASE]

FIGURE 2

BASE COUNTERWEIGHT SCREWS[H-THPMS-832-516]

5X


BASE COUNTERWEIGHT[X-RS-BCW]

FIGURE 1

BASE COUNTERWEIGHT "C" WASHERS[H-CWSH-10]

5X

PROJECT #: 0378

FOR USE WITH: RS(6/7)-((42(0/2/3/4/6/7/8/9/W))/LCD)(-PKG)

NOTE: PERFORM STEP 1 AND/OR STEP 2 ONLY IF PRODUCT WAS PURCHASED WITH RESPECTIVE COUNTERWEIGHT. IF COUNTERWEIGHTS WERE NOT PURCHASED, PROCEED TO NEXT PAGE.

(OPTIONAL) FOR RS(6/7) PLACE STAND BASE INTO BASE COUNTERWEIGHT AS SHOWN IN FIGURE 1. SECURE BY INSERTING AND TIGHTENING 5X 1.BASE COUNTERWEIGHT SCREWS THROUGH 5X BASE COUNTERWEIGHT "C" WASHERS AND INTO BASE COUNTERWEIGHT USING PHILLIPS #2 HEAD SCREWDRIVER

(OPTIONAL) FOR RS(7) INSERT AND TIGHTEN 10X BASE LEG COUNTERWEIGHT SCREWS THROUGH 5X BASE LEG COUNTERWEIGHTS AND INTO 2.STAND BASE USING PHILLIPS #3 HEAD SCREWDRIVER (FIGURE 2).

CUSTOMER

5 4 3 2 1

DESCRIPTION:

PART NO:

SCALE: DRAWN BY:

CHECKED BY:

SHT. OF

DRAWING NO:NTS 1 6



Assembly instructions for Roll Stand

EC 2014-02-28JT 2014-08-04


RS_-___-___

20140228-E2799

PROJECTION

BASE LEG COUNTERWEIGHT SCREWS[H-FHMS-1420-34]

10X

BASE LEG COUNTERWEIGHTS[X-RS-CW-BASE]

5X


FIGURE 2

BASE COUNTERWEIGHT SCREWS[H-THPMS-832-516]

5X



FIGURE 1

BASE COUNTERWEIGHT "C" WASHERS[H-CWSH-10]

5X

PROJECT #: 0378

FOR USE WITH: RS(6/7)-((42(0/2/3/4/6/7/8/9/W))/LCD)(-PKG)

NOTE: PERFORM STEP 1 AND/OR STEP 2 ONLY IF PRODUCT WAS PURCHASED WITH RESPECTIVE COUNTERWEIGHT. IF COUNTERWEIGHTS WERE NOT PURCHASED, PROCEED TO NEXT PAGE.

(OPTIONAL) FOR RS(6/7) PLACE STAND BASE INTO BASE COUNTERWEIGHT AS SHOWN IN FIGURE 1. SECURE BY INSERTING AND TIGHTENING 5X 1.BASE COUNTERWEIGHT SCREWS THROUGH 5X BASE COUNTERWEIGHT "C" WASHERS AND INTO BASE COUNTERWEIGHT USING PHILLIPS #2 HEAD SCREWDRIVER

(OPTIONAL) FOR RS(7) INSERT AND TIGHTEN 10X BASE LEG COUNTERWEIGHT SCREWS THROUGH 5X BASE LEG COUNTERWEIGHTS AND INTO 2.STAND BASE USING PHILLIPS #3 HEAD SCREWDRIVER (FIGURE 2).

CUSTOMER

5 4 3 2 1

DESCRIPTION:

PART NO:

SCALE: DRAWN BY:

CHECKED BY:

SHT. OF

DRAWING NO:NTS 1 6




EC 2014-02-28JT 2014-08-04


RS_-___-___

20140228-E2799

PROJECTION

Roll Stand Base

5x BASE COUNTERWEIGHT SCREWS

[H-THPMS-832-516]

5x BASE COUNTERWEIGHT“C” WASHERS[H-CWSH-10]


10x BASE LEG COUNTERWEIGHT SCREWS

[H-FHMS-1420-34]

5x BASE LEGCOUNTERWEIGHTS

[X-RS-CW-BASE]





Roll Stand Base Assembly:

WARNING: DO NOT USE A HAMMER ON THE CASTERS OR ROLL STAND BASE WHEN INSTALLING CASTERS. THIS WILL DAMAGE THE CASTERS.

1. Push each of the five CASTERS into a base leg by hand until the CASTER clicks into place (Figure 1).

2. Insert the STAND POST into the BASE ADAPTER at the top of the STAND BASE. Using a ½" socket wrench and POST-HW KIT secure by inserting the POST-HW KIT LARGE SCREW through the POST-HW KIT LOCK WASHER and POST HW-KIT SMALL WASHER into the underside of the STAND BASE, STAND ADAPTER and into the STAND POST (Figure 2).

NOTE: POST-HW KIT contains all necessary hardware for this section.

NOTE: To lock the casters, step on the locking level until it clicks in the down position.To unlock the caster, lift up the locking lever.


(Figure 3)

STAND POST[X-RS-POST]

BASE ADAPTER[RS-ADA-125]


POST HW-KIT SMALL WASHER[H-STW-516-SMOD]

POST HW-KIT LOCK WASHER[H-RS-LOCK-WASH]

POST HW-KIT LARGE BOLT[H-HSCS-51618-312]

FIGURE 1

CASTERS[X-RS-CSTR-3B]

5X


PROJECT #: 0378

FOR USE WITH: RS(5/6/7)-((42(0/2/3/4/6/7/8/9/W))/LCD)(-PKG)

WARNING: DO NOT USE A HAMMER ON THE CASTERS OR ROLL STAND BASE WHEN INSTALLING CASTERS. DOING SO WILL DAMAGE THE CASTERS

PUSH 5X CASTERS INTO STAND BASE BY HAND UNTIL IT CLICKS IN PLACE, AS SHOWN IN FIGURE 1.1.

INSERT STAND POST INTO BASE ADAPTER. USING 1/2" SOCKET WRENCH, SECURE BY INSERTING POST HW-KIT-LARGE BOLT THROUGH POST 2.HW-KIT LOCK WASHER, POST HW-KIT SMALL WASHER, STAND BASE, BASE ADAPTER, AND INTO STAND POST, AS SEEN IN FIGURE 2.

CUSTOMER

FIGURE 2

5 4 3 2 1

DESCRIPTION:

PART NO:

SCALE: DRAWN BY:

CHECKED BY:

SHT. OF

DRAWING NO:NTS 2 6




EC 2014-02-28JT 2014-08-04


RS_-___-___

20140228-E2799

PROJECTION







FIGURE 1

CASTERS[X-RS-CSTR-3B]

5X


PROJECT #: 0378


WARNING: DO NOT USE A HAMMER ON THE CASTERS OR ROLL STAND BASE WHEN INSTALLING CASTERS. DOING SO WILL DAMAGE THE CASTERS

PUSH 5X CASTERS INTO STAND BASE BY HAND UNTIL IT CLICKS IN PLACE, AS SHOWN IN FIGURE 1.1.

INSERT STAND POST INTO BASE ADAPTER. USING 1/2" SOCKET WRENCH, SECURE BY INSERTING POST HW-KIT-LARGE BOLT THROUGH POST 2.HW-KIT LOCK WASHER, POST HW-KIT SMALL WASHER, STAND BASE, BASE ADAPTER, AND INTO STAND POST, AS SEEN IN FIGURE 2.

CUSTOMER

FIGURE 2

5 4 3 2 1

DESCRIPTION:

PART NO:

SCALE: DRAWN BY:

CHECKED BY:

SHT. OF

DRAWING NO:NTS 2 6




EC 2014-02-28JT 2014-08-04


RS_-___-___

20140228-E2799

PROJECTION

LOCK

UNLOCK

LOCKINGLEVER

PROJECT #: 0378


TO LOCK THE CASTERS, STEP ON THE LOCKING LEVER SUCH THAT IT CLICKS IN THE DOWN POSITION.1.TO UNLOCK THE CASTERS, LIFT THE LOCKING LEVER UP2.

CUSTOMER

FIGURE 1

5 4 3 2 1

DESCRIPTION:

PART NO:

SCALE: DRAWN BY:

CHECKED BY:

SHT. OF

DRAWING NO:NTS 6 6




EC 2014-02-28JT 2014-08-04


RS_-___-___

20140228-E2799

PROJECTION

5x CASTERS[X-RS-CSTR-3B]






Unlock

LockingLever

Lock



www.amico.com 10

Roll Stand Head Assembly

WARNING: ENSURE THAT THERE IS NO GAP BETWEEN THE LARGE PLASTIC BUSHING AND THE MONITOR HEAD AFTER ASSEMBLY.

1. Using a ½" socket wrench and HEAD HW-KIT, insert the HEAD HW-KIT LARGE SCREW through the HEAD HW-KIT BRONZE WASHER, then through the HEAD HW-KIT NYLON WASHER. Then, insert the screw and washers into the top of the MONITOR HEAD, down through the black PLASTIC BUSHING, into the STAND BASE and STAND POST (Figure 1).

2. Cover the head of the HEAD HW-KIT LARGE SCREW with the CAUTION STICKER doming label by placing the adhesive side down onto the MONITOR HEAD (Figure 1).


HEAD-HW KIT

NOTE: HEAD-HW KIT contains the hardware necessary for this section.

HEAD HW-KIT NYLON WASHER[H-NYL-WSH-516]

HEAD HW-KIT BRONZE WASHER[H-BZWASH-516-34]

HEAD HW-KIT LARGE BOLT[H-SCS-51618-35]

MONITOR HEAD[X-MONHEAD-_]

PLASTIC BUSHING[X-MON-BUSH-SM]

POST ADAPTER[RS-ADA-125]


FIGURE 1

CAUTION STICKER[X-LBL-MAX-15]

PROJECT #: 0378


USING 1/2" SOCKET WRENCH, INSERT HEAD HW-KIT LARGE BOLT THROUGH HEAD HW-KIT-BRONZE WASHER, HEAD HW-KIT NYLON 1.WASHER, MONITOR HEAD, PLASTIC BUSHING, POST ADAPTER, AND INTO STAND POST AS SHOWN IN FIGURE 1.

COVER THE HEAD OF HEAD HW-KIT LARGE BOLT WITH CAUTION STICKER BY PLACING THE ADHESIVE SIDE DOWN ONTO THE MONITOR 2.HEAD

CUSTOMER

5 4 3 2 1

DESCRIPTION:

PART NO:

SCALE: DRAWN BY:

CHECKED BY:

SHT. OF

DRAWING NO:NTS 3 6




EC 2014-02-28JT 2014-08-04


RS_-___-___

20140228-E2799

PROJECTION

AMICO STICKER[X-DOME-CIR-LBL]

AMICO STICKER[X-DOME-CIR-LBL]

HEAD HW-KIT LARGE BOLT

[H-SCS-51618-35]

HEAD HW-KIT LARGE BOLT

[H-SCS-51618-35]

HEAD HW-KIT NYLON WASHER

[H-NYL-WSH-516] HEAD HW-KIT NYLON WASHER

[H-NYL-WSH-516]




HEAD HW-KIT BRONZE WASHER

[H-BZWASH-516-34]

HEAD HW-KIT BRONZE WASHER

[H-BZWASH-516-34]

MONITOR HEAD[X-MONHEAD-_]



(Figure 1)


Roll Stand Handle Assembly

WARNING: DO NOT TIGHTEN ONE SCREW ALL THE WAY PRIOR TO INSERTING THE OTHER. START BY INSERTING BOTH SCREWS HALF WAY, THEN TIGHTEN EACH SCREW INCREMENTALLY, ENSURING THAT THE TWO HALVES OF THE HANDLE REMAIN PARALLEL WITH ONE ANOTHER. FAILURE TO DO SO MAY CAUSE DAMAGE TO THE EQUIPMENT.

1. Once at desired height (typically 2" below the POST ADAPTER), place the ROLL STAND HANDLE BACK PIECE and ROLL STAND HANDLE FRONT PIECE around the STAND POST. Secure the ROLL STAND HANDLE in place by inserting the HANDLE KIT SCREWS through the back piece and tightening into the larger piece, using Phillips #2 head screwdriver (Figure 1).


(Figure 1)

(Figure 2)

INCORRECT

HANDLE KIT SCREWS[H-PHMS-1032-916]

(PART OF RS1-HANDLE)

2X

SMALLER PIECE OF ROLL STAND HANDLE

[RS1-HANDLE]


LARGER PIECE OF ROLL STAND HANDLE

[RS1-HANDLE]

PROJECT #: 0378


WARNING: DO NOT TIGHTEN ONE SCREW ALL THE WAY PRIOR TO INSERTING THE OTHER. START BY INSERTING BOTH SCREWS HALF WAY, THEN TIGHTEN EACH SCREW INCREMENTALLY, ENSURING THAT THE TWO HALVES OF THE ROLL STAND HANDLE REMAIN PARALLEL WITH ONE ANOTHER. FAILURE TO DO SO MAY CAUSE DAMAGE TO THE PRODUCT.

AT DESIRED HEIGHT, PLACE TWO HALVES OF ROLL STAND HANDLE AROUND STAND POST AS SHOWN IN FIGURE 1. SECURE ROLL STAND HANDLE IN 1.PLACE BY INSERTING 2X HANDLE KIT SCREWS THROUGH THE SMALLER PIECE OF THE ROLL STAND HANDLE, AND TIGHTENING INTO THE LARGER PIECE OF ROLL STAND HANDLE, USING PHILLIPS #2 HEAD SCREWDRIVER

CUSTOMER

CORRECT!

FIGURE 1FIGURE 2

5 4 3 2 1

DESCRIPTION:

PART NO:

SCALE: DRAWN BY:

CHECKED BY:

SHT. OF

DRAWING NO:NTS 4 6




EC 2014-02-28JT 2014-08-04


RS_-___-___

20140228-E2799

PROJECTION

INCORRECT



2X


[RS1-HANDLE]



[RS1-HANDLE]

PROJECT #: 0378




CUSTOMER

CORRECT!

FIGURE 1FIGURE 2

5 4 3 2 1

DESCRIPTION:

PART NO:

SCALE: DRAWN BY:

CHECKED BY:

SHT. OF

DRAWING NO:NTS 4 6




EC 2014-02-28JT 2014-08-04


RS_-___-___

20140228-E2799

PROJECTION

Smaller piece ofROLL STAND HANDLE

[RS1-HANDLE]

Larger piece ofROLL STAND HANDLE

[RS1-HANDLE]


CorrectIncorrect

2x HANDLE KIT SCREWS[H-PHMS-1032-916]

(Parts of RS1-HANDLE)

www.amico.com 12

Roll Stand Basket Assembly

WARNING: DO NOT TIGHTEN ONE SCREW ALL THE WAY PRIOR TO INSERTING THE OTHERS. START BY INSERTING ALL SCREWS HALF WAY, THEN TIGHTEN EACH SCREW INCREMENTALLY IN A CROSS PATTERN, ENSURING THAT THE POST CLAMPS REMAIN PARALLEL. FAILURE TO DO SO MAY CAUSE DAMAGE TO THE EQUIPMENT (Figure 2).

1. Remove the BASKET POLE CLAMP FRONT HALF from the BASKET POLE CLAMP BACK HALF by unscrewing the four REAR BASKET SCREWS (BLACK), using a 3/16" wrench (Figure 1).

2. Once at desired height (typically 2" below the roll stand basket), place the STAND POST between the front and back clamp halves and replace the screws using a 3/16" hex key in a cross pattern (Figures 1 and 3).


Tighten using Cross Pattern

(Figure 1)

(Figure 2)(Figure 3)

INCORRECT



2X


[RS1-HANDLE]



[RS1-HANDLE]

PROJECT #: 0378




CUSTOMER

CORRECT!

FIGURE 1FIGURE 2

5 4 3 2 1

DESCRIPTION:

PART NO:

SCALE: DRAWN BY:

CHECKED BY:

SHT. OF

DRAWING NO:NTS 4 6




EC 2014-02-28JT 2014-08-04


RS_-___-___

20140228-E2799

PROJECTION

REAR BASKET SCREWS (BLACK)[H-HSCS-1420-34]

(PART OF 100609-R125-BB)

4X

BASKET POLE CLAMP BACK HALF[X-PC-125-2-8-32]

(PART OF 100609-R125-BB)

2X

BASKET POLE CLAMP FRONT HALF[X-PC-125-1-8-32]

(PART OF 100609-R125-BB)

2X


INCORRECT

PROJECT #: 0378


WARNING: DO NOT TIGHTEN ONE SCREW ALL THE WAY PRIOR TO INSERTING THE OTHERS. START BY INSERTING ALL SCREWS HALF WAY, THEN TIGHTEN EACH SCREW INCREMENTALLY IN A CROSS PATTERN, ENSURING THAT THE 2X BASKET POLE CLAMP BACK HALF REMAIN PARALLEL WITH THE 2X BASKET POLE CLAMP FRONT HALF. FAILURE TO DO SO MAY CAUSE DAMAGE TO THE PRODUCT.

REMOVE 2X BASKET POLE CLAMP BACK HALF FROM 2X BASKET POLE CLAMP FRONT HALF BY UNSCREWING 4X REAR BASKET SCREWS USING 1.3/16" ALLEN WRENCH

AT DESIRED HEIGHT, PLACE STAND BETWEEN BASKET POLE CLAMP FRONT HALF AND BASKET POLE CLAMP BACK HALF AS SHOWIN IN FIGURE 1 2.AND INSERT 4X REAR BASKET SCREWS THROUGH 2X BASKET POLE CLAMP BACK HALF, AND INTO 2X BASKET POLE CLAMP FRONT HALF, USING 3/16" ALLEN WRENCH.

CUSTOMER

CORRECT!

FIGURE 1

FIGURE 2

5 4 3 2 1

DESCRIPTION:

PART NO:

SCALE: DRAWN BY:

CHECKED BY:

SHT. OF

DRAWING NO:NTS 5 6




EC 2014-02-28JT 2014-08-04


RS_-___-___

20140228-E2799

PROJECTION

Correct


2x BASKET POLE CLAMP BACK HALF[X-PC-125-2-8-32]

(Part of 100609-R125-BB)

4x REAR BASKET SCREWS (BLACK)[H-HSCS-1420-34]

(Part of 100609-R125-BB)

2x BASKET POLE CLAMP FRONT HALF[X-PC-125-1-8-32]

(Part of 100609-R125-BB)

Incorrect


WARNING: ENSURE THE MONITOR SHELVES AND PLATES PROVIDED BY AMICO ACCESSORIES OR OTHER MANUFACTURERS ARE ASSEMBLED AS DIRECTED AND MATCH THE SHELF REQUIREMENTS. IF A MONITOR SHELF OR PLATE DOES NOT MATCH THE REQUIREMENTS, PLEASE CONTACT AMICO ACCESSORIES AT 1-877-264-2697.

Section 4: Device Installation

www.amico.com 14

Monitor Shelf: 3" (76.2 mm) Bottom/Back Mount, 5" (127 mm) Bottom/Back Mount and VESA Quick Release

WARNING: ENSURE THE MOUNTING SHELF IS SECURELY LOCKED AND HORIZONTAL TO PREVENT THE MONITOR FROM SLIDING AND FALLING.

WARNING: ON THE BOTTOM OF THE MOUNTING SHELF, THERE IS A PLUNGER THAT SECURES THE SHELF TO THE MOUNTING ADAPTER. SIMPLY PULL DOWN ON THE PLUNGER, ALIGN THE ADAPTER PLATE WITH THE SHELF AND RELEASE THE PLUNGER ONCE POSITIONED OVER THE CLEARANCE HOLE.

NOTE: The plunger can be locked in the open position by pulling and twisting it.


1. First, install the MOUNTING ADAPTER to the device (please refer to the adapter installation manual provided with the adapter) (Figure 1).

2. Loosen the plastic screws on the bottom side of the MOUNTING SHELF. Pull down on the plunger lock at the back of the mounting shelf. Twist to lock open. Slide the adapter laterally onto the MOUNTING SHELF until the plunger aligns with the clearance hole at the front of the MOUNTING ADAPTER (Figure 3).

3. Release the plunger and tighten the plastic screws by hand (Figure 4).

MOUNTING ADAPTER

MONITOR DEPENDANT HARDWARE

MONITOR

FRONT OF THE MOUNTING ADAPTER


MOUNTING SHELF

PLUNGER LOCK

PLASTIC SCREWS

FRONT OF THE SHELF

5" (127 mm) MOUNTING SHELF is shown above

(Figure 4)

Plunger pulled

Plunger released

MOUNTING SHELF

(Figure 3)


Monitor Shelf: 6" (152.4 mm) Drop-On

WARNING: ENSURE THE MOUNTING SHELF IS SECURE AND LOCKED IN THE VERTICAL POSITION TO PREVENT THE MONITOR FROM SLIDING AND/OR FALLING.

NOTE: Quick installation system: on the back of the MOUNTING SHELF, there is a plunger that secures the adapter to the MOUNTING SHELF. Simply slide and align the adapter to the shelf and the plunger will automatically engage and lock.

1. First, install the MOUNTING ADAPTER to the back of the monitor (please refer to the adapter installation manual provided with the adapter).

2. Lift the monitor and slide the MOUNTING ADAPTER on to the MOUNTING SHELF. Slide the monitor laterally until the mounting hole on the MOUNTING ADAPTER aligns with the plunger (Figure 1). When the hole and the plunger are aligned, the plunger will automatically lock. If the plunger does not lock automatically, lock the plunger manually by turning it. Tighten the locking screws by hand to the tightest possible position (Figure 2).


(Figure 1)

MOUNTING SHELF

MOUNTING ADAPTER

MOUNTING HOLE

(Figure 2)

LOCKING SCREWS

PLUNGER LOCK

www.amico.com 16

Monitor Shelf: Philips IntelliVue

WARNING: ENSURE THE MOUNTING SHELF IS FIRMLY LOCKED AND HORIZONTAL TO PREVENT THE MONITOR FROM SLIDING AND FALLING.

NOTE: Philips recommends a maximum tilt of 15 degrees.

NOTE: It is recommended to use M6 x 20 mm screws with a thread locker or patched screws in order to eliminate possible danger.

1. Attach the table top mount from Philips (not supplied by Amico) to the MOUNTING SHELF by securing the three (3) screws through the shelf (Figure 2).

2. Place the monitor on the table top mount until it clicks (Figure 3).

3. Tilt the monitor to the desired angle and re-adjust the tension as needed with a 12 mm wrench (Figure 4).

Monitor Shelf: Welch Allyn

WARNING: ENSURE THE MOUNTING SHELF IS FIRMLY LOCKED AND HORIZONTAL TO PREVENT THE MONITOR FROM SLIDING AND FALLING.

1. To attach the monitor to the Welch Allyn shelf, lift the monitor to match the front lip of the mounting plate. Slide the monitor laterally until the mounting hole on the monitor aligns with the thumb screw on the adapter.

2. Tighten the thumb screw by hand to the tightest possible position.


(Figure 3) (Figure 4)(Figure 2)

MOUNTING SHELF

THREE 3-3/4" (20 MM) M6 SCREWS

TABLE TOP MOUNT

To loosen

To tighten

12 MM HEX NUT

PHILIPS TABLETOP MOUNT (Not supplied)

(Figure 1)

(Figure 1)

THUMB SCREW

FRONT LIP

(Figure 2)

THUMB SCREW


Monitor Shelf: VESA

NOTE: Setting the VESA shelf horizontally can make the mounting procedure easier.

NOTE: A VESA plate for the 5" (127 mm) shelf is available through Amico Accessories.

NOTE: If the original monitor bolts are too large, simply enlarge the mounting holes on the VESA plate to fit.

1. Determine the monitor mounting configuration. VESA-75 (75 mm x 75 mm, M4 thread) or VESA-100 (100 mm x 100 mm, M4 thread).

2. VESA-75/100 configuration: Partially thread two screws into the top two holes in the back of the monitor. The monitor can then be hung up on the VESA Head through the two slots at the top. Insert two more screws through the VESA-75/100 mounting holes at the bottom and tighten all screws.

3. When removing the monitor, remove the two bottom screws from the VESA plate. Loosen the top two screws, and lift the monitor off the VESA plate.


LCD MODEL HEAD

www.amico.com 18

Accessory Shelf: Disc

Amico Accessories carries a variety of different accessories that attach to the Accessory Shelf Disc.

To install and mount your accessory to your Accessory Shelf, insert the three screws provided with the accessory similar to as shown below. Please note the picture is for reference only.


6" and 12" (15.24 cm and 30.38 cm) POST(Part Numbers: DOWNPOST-06/

DOWNPOST-12)

SINGLE OR DUAL CORD HOLDER(Part Numbers: CRDHLDR/CRDHLDR2)

(Part Number: MON-SWIV-DISK-T)

KEYBOARD HANDLE(Part Number: AHM-HAND-00)

LAPTOP HOLDER(Part Number: Please call)

3x HEX FLAT HEAD SCREWS

KEYBOARD TRAY

ACCESSORY SHELF

Screw type: 10 x 32

Top side

KEYBOARD TRAY(Part Number: Please call)


Monitor Tilt

WARNING: BE SURE TO SUPPORT THE MONITOR IF ADJUSTING THE TILT ANGLE WHILE THE MONITOR IS MOUNTED.

WARNING: FOR HEAVIER MONITORS, IT IS STRONGLY RECOMMENDED TO CHECK WHETHER THE ADJUSTMENT LEVER IS TIGHTENED TO THE TIGHTEST POSITION WITH THE WEIGHT OF THE MONITOR ATTACHED. IF THE ADJUSTMENT LEVER CANNOT BE TIGHTENED ENOUGH TO LOCK THE MONITOR IN PLACE, REMOVE THE ADJUSTMENT LEVER USING A 4 MM HEX KEY, AND USE THE 12 MM HEX NUT INSIDE TO ADJUST.

WARNING: NEVER ATTEMPT TO TILT WITHOUT FIRST LOOSENING THE HANDLE.

NOTE: For heavier loads or to prevent tampering, it is recommended to remove the adjustment handle using a 4 mm hex key and use the 12 mm hex nut to adjust (Figure 1).

To tilt, support the monitor first and loosen the adjustment lever by turning the lever counter-clockwise, grasp the top and bottom of the device and tilt it to the desired angle. Re-secure the adjustment lever (Figures 2 and 3).

Section 5: Adjustments

(Figure 1)

12 mm hex nut for heavy duty or tamper proof applicationsTo loosen

To tighten

4 mm hex key to loosen handle

Heavy Duty Head Tilt

To tilt the monitor (Figures 4 and 5):

1. Support the monitor.

2. Loosen the socket cap screws using a ¼" hex key by rotating it counter clockwise.

3. Tilt monitor to desired position.

4. Use a ¼" hex key to fully tighten both of the socket cap screws or tighten to desired tension.

(Figure 3)

Adjustment lever

(Figure 2)

Loosen lever

5 4 3 2 1

DESCRIPTION:

PART NO:

SCALE: DRAWN BY:

CHECKED BY:

SHT. OF

DRAWING NO:NTS 1 1


ALL RIGHTS TO DESIGN OR INVENTION ARE RESERVEDDATE:DATE:- -/-/-


(Figure 4)

Tilt

Lever

5 4 3 2 1

DESCRIPTION:

PART NO:

SCALE: DRAWN BY:

CHECKED BY:

SHT. OF

DRAWING NO:NTS 1 1


ALL RIGHTS TO DESIGN OR INVENTION ARE RESERVEDDATE:DATE:- -/-/-


(Figure 5)

Socket cap screws

www.amico.com 20

Section 6: Maintenance, Troubleshooting and Product ClassificationTroubleshooting Guide

Symptom Solution

Roll stand is difficult to move One or more casters are locked. Ensure that all locks are in the up position. If problem persists, contact Amico Accessories.

Roll stand moves when it should not One or more casters are unlocked. Ensure that all locks are in the down position. If problem persists, contact Amico Accessories.

Head of roll stand is loose Remove device from head of roll stand. Tilt head down, if required. Ensure bolt on top is tight, using a ½" socket wrench. If problem persists, contact Amico Accessories.

Handle is loose Ensure 2x screws are tight, using a #2 head Phillips screwdriver. If problem persists, contact Amico Accessories.

Basket is loose Ensure 4x screws are tight, using a 3/16" hex key. If problem persists, contact Amico Accessories.

Counterweights are loose Lock 5x casters. Remove all devices from the roll stand. Carefully tilt the roll stand over, resting it on a smooth surface.

For RS6 models, ensure 5x screws securing the base counterweight are tight, using a #2 head Phillips screwdriver.

For RS7, ensure 5x base counterweight screws and 10x leg counterweight screws are tight, using a #3 head Phillips screwdriver.


Section 6: Maintenance, Troubleshooting and Product Classification

No AcetoneAcetone is a colorless, mobile, flamable liquid

No TrichloroethyleneTrichloroethylene is a chlorinated hydrocarbon commonly used a ans individual solvent

Acetone Trichloroethylene

Preventative Maintenance

It is recommended that once every three (3) months, all bolts and screws are checked to ensure that they are tight. Visually inspect product for signs of damage based on degree of usage.

Cleaning

WARNING: THE CLEANING CHEMICALS AND METHODS BELOW ARE NOT MEANT FOR INFECTION CONTROL. IT SHALL BE THE RESPONSIBILITY OF THE FACILITY, CLINIC, HOSPITAL OR THE INFECTION CONTROL OFFICER TO SANITIZE THE EQUIPMENT.

WARNING: PLEASE DO NOT SPRAY ANY CHEMICAL DIRECTLY ONTO RS MODELS. APPLY ONTO A SOFT CLOTH AND WIPE CLEAN TO PREVENT CHEMICALS GETTING INTO THE INTERNAL COMPONENTS OF RS MODELS.

The mounting assembly can be cleaned with most mild non-abrasive solutions commonly used in the hospital environment (e.g. diluted bleach, ammonia, alcohol). The surface finish will be permanently damaged by strong chemical and solvents such as acetone and trichloroethylene. Steel wool or other abrasive material should never be used. Damage caused by the use of unapproved substances or processes will not be warranted. It is recommended that you test any cleaning solution on a small area of the RS model that is not visible to verify compatibility. Never submerge the RS model and do not allow liquids to enter. Wipe any cleaning agents off the RS models immediately using a water-dampened cloth. Dry thoroughly after.


www.amico.com 22 www.amico.com www.amico.com

Amico Accessories Inc. warrants all mounting accessories to be free from defects in material and workmanship for a period of twelve (12) months from the date of shipment. Within this period Amico Accessories Inc. will repair or replace any part which is proven to be defective.

Amico Accessories Inc. will warrant its materials to be free from defect for an additional period of four (4) years, (five [5] years from the date of shipment). Within this period, Amico Accessories Inc. will replace any part which is proven to be defective, at no charge. Shipping and Installation costs after the first twelve (12) months will be borne by the Customer.

This warranty is valid only when the product has been properly installed according to Amico Accessories Inc. specifications, used in a normal manner and serviced according to factory recommendations. It does not cover products that are not manufactured by Amico Accessories Inc. It does not cover failures due to damage which occurs in shipments or failures which result from accidents, misuse, abuse, neglect, mishandling, alteration, misapplication or damage that may be attributable to acts of God.

Amico Accessories Inc. shall not be liable for incidental or consequential damages resulting from use of equipment.

All claims for warranty must first be approved by Amico Accessories Inc. A valid Return Goods Authorization (RGA) number must be obtained from Amico Accessories Inc. prior to commencement of any service work. Warranty work, which has not been pre-authorized by Amico Accessories Inc., will not be reimbursed.

AMICO ACCESSORIES INC. DOES NOT HONOR VERBAL STATEMENTS CONCERNING THE WARRANTY.

The distributor and/or dealer are not sanctioned to create verbal warranties about the product described in this agreement. Any statements will not be honored or be made part of the agreement of sale. This document is the final complete and exclusive terms of the agreement.

THIS WARRANTY IS INCLUSIVE AND REPLACES ALL OTHER WARRANTIES.

Amico Accessories Inc. shall not, under any circumstances be liable for incidental or consequential damages including, but not limited to, profit, loss of sales or injuries to person(s) or property. Correction of noncompliance as noted above will result in completion of all liabilities of Amico Accessories Inc., whether based on agreement, neglect or changed materials, designs or specifications without notice.

All claims for warranty must first be approved by Amico Accessories Inc. Service Department: [email protected] or 1.877.264.2697). A valid Return Goods Authorization number must be obtained from Amico Accessories Inc. prior to commencement of any warranty claim.

Amico Accessories Inc. 85 Fulton Way, Richmond Hill, ON L4B 2N4, Canada71 East Industry Court, Deer Park, NY 11729, USA

Tel: 905.763.7778 | Fax: 905.763.8587

Warranty Policy - Equipment Mounting Solutions

www.amico.com

AA-IM-MNTR-RLSTD 04.16.2018

Amico Accessories Inc. | 85 Fulton Way, Richmond Hill, ON L4B 2N4, CanadaToll Free Tel: 1.877.264.2697 | Tel: 905.763.7778 | Fax: 905.763.8587Email: [email protected] | www.amico.com

Date post:	22-Oct-2020
Category:	Documents
Upload:	others
View:	0 times
Download:	0 times

Installation Instructions Roll Stand · Philips IntelliVue Shelf w/ 30° tilt limit 2 6" (152 mm)...

Documents