High speed Scanner Model No. KV-S3085 This manual contains information on installing the scanner. Please read this manual before operating unit. For information on operating the scanner, please read the operating instructions recorded on the CD-ROM enclosed with this unit. For information on maintaining the scanner, please read the maintenance manual enclosed with this unit. Please carefully read this manual, the operating instructions and maintenance manual. Keep these documents in a safe place for future reference. Installation Manual High Speed Color Scanner Model No. KV-S3105C
Transcript
High speed ScannerModel No. KV-S3085
This manual contains information on installing the scanner. Please read this manual beforeoperating unit.For information on operating the scanner, please read the operating instructions recorded on theCD-ROM enclosed with this unit.For information on maintaining the scanner, please read the maintenance manual enclosed withthis unit.
Please carefully read this manual, the operating instructions and maintenance manual.Keep these documents in a safe place for future reference.
Installation Manual
High Speed Color Scanner
Model No. KV-S3105C
Thank you for purchasing a Panasonic “High Speed Color Scanner” or “High Speed Scanner”.
≥ A versatile solution for your imaging needs, Panasonic developed Panasonic Image Enhancement Technology to improve the quality of your originals.
≥ With our easy to use functions, reliable paper handling, easy maintenance and more, Panasonic is ready to contribute to your imaging needs.
Things you should keep a record of:
Important
≥ Do not duplicate currency.
≥ Do not duplicate copyrighted material or the work of others except for the purpose of private use.
≥ Do not duplicate any kind of certificates, licenses, passports, official or private documents, and the like.
As an ENERGY STAR® Partner, Panasonic has determined that this product meets theENERGY STAR guidelines for energy efficiency.(ENERGY STAR and the ENERGY STAR certification mark are registered US marks.)
≥ Microsoft, Windows and Windows NT are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
≥ ISIS is a registered trademark of Pixel Translations, a division of Captiva Software Corporation.≥ Adobe, Acrobat and Reader are registered trademarks of Adobe Systems Incorporated in the United States
and/or other countries.≥ Pentium is a trademark or registered trademark of Intel Corporation or its subsidiaries in the United States and
other countries.≥ Adaptec is a registered trademark of Adaptec, Inc.≥ Each company’s name or company product name is each company’s trademark or registered trademark.
The information given in this Installation Manual is subject to change without notice.
*Microsoft® Windows NT operating system (hereafter Windows NT)
Notice
Roller cleaning paper precautionsBefore using the roller cleaning paper, please read these instructions completely. Keep these instructions for futurereference.
Federal Communications Commission Requirements(For United States only)
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant topart 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment. This equipment generates, uses,and can radiate radio frequency energy and, if not installed and used in accordance with the instructionmanual, may cause harmful interference to radio communications. Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correct theinterference at his own expense.
English
WARNING:TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN ORANY TYPE OF MOISTURE.
THE SOCKET-OUTLET MUST BE NEAR THIS EQUIPMENT AND MUST BE EASILYACCESSIBLE.
The product should be used only with a power cord that is supplied by the manufacturer.
Power SourceWARNING≥ (220-240 V equipment)
A certified power supply cord has to be used with this equipment. The relevant national installation and/or equipment regulations shall be considered. A certified power supply cord not lighter than ordinary polyvinyl chloride flexible cord according to IEC 60227 (designation H05VV-F 3G 1.0 mm2).
WARNING• Do not drink or inhale the roller cleaning paper fluid including isopropyl alcohol.• The roller cleaning paper may be harmful to sensitive skin. Please use protective gloves.• Do not use the roller cleaning paper near a heater or open flame.• Do not store the roller cleaning paper in direct sunlight or in a place with temperature over 40 oC (104 oF).• Only use the roller cleaning paper to clean the rollers and scanning area.• If you need more information about the roller cleaning paper, please refer to the Material Safety Data Sheet
(MSDS).• Please ask your Panasonic sales company about obtaining the Material Safety Data Sheet.
KEEP AWAY FROM FIRE.
FCC Warning: To assure continued FCC compliance, the user must use only shielded interface cable and the provided power supply cord. Also, any unauthorized changes or modifications to this equipment would void the user’s authority to operate this device.
4
Notice
(For United Kingdom only)For your safety please read the following text carefully.This appliance is supplied with a moulded three pin mains plug for your safety and convenience.A 5 amp. fuse is fitted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 5amps. and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark or the BSI mark on the body of thefuse. If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced. If you lose the fusecover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from yourlocal Panasonic Dealer.
If the fitted moulded plug is unsuitable for the socket outlet in your home then the fuse should be removed and the plug cut off anddisposed of safely.There is danger of severe electrical shock if the cut off plug is inserted into any 13 amp. socket. If a new plug is to be fitted please observe the wiring code as shown below. If in any doubt please consult a qualified electrician.WARNING: This appliance must be earthed.IMPORTANT: The wires in this mains lead are coloured in accordance with the following code.
Green-and-Yellow : EarthBlue : NeutralBrown : Live
As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying theterminals in your plug, proceed as follows.
The wire which is coloured Green-and-Yellow must be connected to the terminal in the plug which is marked with the letter E or bythe Earth symbol or coloured Green-and-Yellow.The wire which is coloured Blue must be connected to the terminal in the plug which is marked with the letter N or coloured Black.The wire which is coloured Brown must be connected to the terminal in the plug which is marked with the letter L or coloured Red.
ASA
How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.
5
Notice
Caution Labels
注意ローラーに手を触れないでください。指を巻き込まれてけがの原因になります。
6
Precautions
The following precautions are recommended to extend the life of the unit:
≥ Special care should be taken to protect the unit if it is used in a less than optimum environment, such as a dusty or sandy area.
Prior to scanning, remove all sta-ples and paper clips from pages.
Do not place any liquids near theunit.
—Accidental spillage of liquid intothe unit may cause severe dam-age. If this occurs, turn the unitoff, unplug the power cord andcall for service.
Do not place books, paper, or otheritems on the unit.
Do not place the unit in an area where there is a lot ofsmoke, dust, chemical fumes or vibration.
Do not leave the power cord plugged into the AC outletif the unit will not be used for an extended period.
Do not place the unit on an unevenor unstable surface.
Do not disassemble the unit.This will void your warranty.
Stop operation immediately if theunit emits smoke, excessive heat,abnormal smell, or unusual noise.These conditions can cause fire orelectric shock. Immediately unplugthe power cord and call for service.
Do not insert your fingers into the back opening in thescanner.
It is recommended that if the scanner has to be moved,at least two people carry it.
Ex: ThinnerEx:
7
Precautions
Operating Environment
≥ Power Source≥ Use a voltage level that does not vary more than d10% from the voltage level marked on the nameplate
(located on the back side of the scanner).≥ Do not use an extension cord.≥ This scanner should be connected to a grounded outlet.≥ Do not use a line conditioner, transient suppressor or surge protector.
Do not place the unit in direct sunlight or in a cold draft. Do not operate or place the unit in a vertical position.
Do not place the unit near a heating appliance or an airconditioning vent. Do not place the unit in a room withextremely high or low humidity.
Do not place the unit near other appliances which gen-erate large electrical noise.
Do not place the unit on a carpet. (Static electricity cancause the unit to malfunction.)
Do not drink or inhale the included roller cleaning paperfluid.The roller cleaning paper may be harmful to sensitiveskin. Please use protective gloves. Do not use the roller cleaning paper near a heater oropen flame. This may cause a fire.
Hot Cold
8
Precautions
∫ CD-ROMTo prevent the CD-ROMs from accidental damages:
Do not touch or write on the surfaceof the disc.
Do not leave the disc out of itsprotective case.
Do not leave the disc in directsunlight or near heat sources.
Do not place heavy objects on thedisc case or drop the case.
To clean the disc, hold the disc byits edges and wipe it from thecenter to the edges with a dry, softcloth.
9
Installing the Unit
∫ Unpacking and AccessoriesPlease check that all parts are included before installing the scanner.
It is highly recommended to keep the original carton and all packing materials.They are necessary when repacking.
∫ Minimum space requirementsBe sure to maintain the recommended space requirements for proper ventilation.
≥ Installation manual≥ Maintenance manual≥ Roller cleaning paper (3 pieces)≥ Shading paper
≥ Blower
Spacer
≥ Exit tray stopper
≥ Exit stopper
Pallet
Plastic band
Be sure to use a power cord whose shape matches the shape of the electric outlet.
≥ USB cable
Clearance needed to open back door:350 mm (13.8")
Clearance needed to turn power ON/OFF: 200 mm (7.9")
Top viewClearance needed to set the pointer lever and the ADF selector: 200 mm (7.9")
10
Installing the Unit
∫ Installing the Exit tray stopper and Exit stopperSqueeze the end of the exit tray stopper metal guides slightly together, and insert them into the stopper slots of the exit tray. Then pull up the plastic part of exit tray stopper.(Install the exit tray stopper in the sequence of 1 through 3.)
When using short paper, put the exit
stopper on the exit tray.
Stopper slots
Exit tray stopper
Exit stopper
11
Installing the Unit
∫ Connecting cables≥ Connect either the USB or SCSI interface cable. Do not connect USB and SCSI cables at the same time.≥ Windows NT 4.0 supports only the SCSI interface.
SCSI ConnectionYou will need to purchase a SCSI cable from your local computer store or dealer.
Caution:≥ Use only with the power cord that is supplied by the manufacturer.≥ It is recommended you use a SCSI cable 3 m (9.8 feet) or less in length that is obtained locally.≥ Set the power switch on the scanner and on the host computer to OFF before connecting the interface cable.≥ If a problem occurs, refer to “Troubleshooting” in the Operating Instructions (CD-ROM).
USB Connection
Caution:≥ Use only with the power cord that is supplied by manufacturer.≥ Use the USB cable provided with the unit.
Household AC outlet≥ AC 100 – 120 V, 50/60 Hz≥ AC 220 – 240 V, 50/60 HzPower cord shown on the figure is for 100 – 120 V.
Power cord
AC inlet
To computer
SCSI connector
Household AC outlet≥ AC 100 – 120 V, 50/60 Hz≥ AC 220 – 240 V, 50/60 HzPower cord shown on the figure is for 100 – 120 V.
Power cord
AC inlet
USB connector
To computer
12
Installing the Unit
∫ System Requirements
*1 Windows 98 is Microsoft Windows 98 operating system.*2 Windows Me is Microsoft Windows Millennium Edition operating system.*3 Windows 2000 is Microsoft Windows 2000 operating system.*4 Windows XP is Microsoft Windows XP operating system.
≥ 1 GB or more free space is required in the HDD.≥ Color images larger than A3 size cannot be scanned in 600 dpi on Windows 98 or Windows Me. A large size color
image may not be scanned in high resolution depending on a computer system or application.≥ The scanning speed differs depending on the host computer operating environment or application.≥ Windows NT 4.0 does not support USB interface.≥ For Windows NT 4.0, you must install the ASPI layer software that the SCSI board vender provides.≥ Use USB 2.0 interface because scanning speed of USB 1.1 interface is slow.≥ If you connect the scanner to a USB hub, it is not guaranteed to work.≥ When using the scanner with other SCSI devices connected by daisy chain connection, it is not guaranteed to
work.
SCSI Connection USB Connection
CPUMinimum Pentium® III, 1 GHz Recommended Pentium 4, 2 GHz or higher
MemoryMinimum 256 MBRecommended 512 MB or higher
OS
Windows® 98*1
Windows NT 4.0Windows 2000*3
Windows Me*2
Windows XP*4
Windows 98 SEWindows 2000 SP4Windows MeWindows XP SP1
Display 1024k768 dots or more, 65536 colors or more
≥ Set the power switch to the “|” position.(The LED and LCD will now light.)
2 When “Ready” appears on the LCD display, turn on the power of the host computer.
∫ About the language setting≥ Select English, German or Japanese as the language which is to appear on the LCD display.≥ The language setting mode is appeared automatically when the unit’s power is turned on for the first time after
the unit was purchased. English is the default language.
1 Turn the power on while pressing theHOME key.
≥ When “High Speed Scanner” or otherwords appear on the LCD, release theHOME key.
2 Use the 2 key or the 1key to select“English Letter”, “English A4”, “Deutsch A4” or “ ”.
3 Press the HOME key.
≥ The display will change to the selectedlanguage, then the scanner will be ready.
≥ This setting will remain until it is changedto another setting.
Power switch
S e t L a n g u a g e ← →E n g l i s h L e t t e r
S e t L a n g u a g e ← →D e u t s c h A 4
(Ex.)
B e r e i t
(Ex.)
14
Installing the Unit
∫ About LEDLED indicates the status of the scanner as follows:
*1: The rollers need to be cleaned or replaced.Refer to Maintenance Manual or Operating Instructions (CD-ROM) for the way of cleaning or replacing therollers.
LED light Status
Green Ready to scan or scanning
Green (flashing) Sleep mode
Orange Initializing or warning
Orange (flashing) Sleeping with warning *1
Red An error occurred
15
Drivers and Utilities CD-ROM
∫ Contents of this CD-ROM
*Color upgrade kit option is required for KV-S3085.
Note:≥ RTIV (Reliable Throughput Imaging Viewer) is a Panasonic original application software, and does not require
either TWAIN driver or ISIS driver.≥ PIE is an acronym for Panasonic Image Enhancement Technology.≥ To view manuals, Adobe® Reader® must be installed.≥ There are no ISIS or TWAIN applications on this CD-ROM.≥ If the CD-ROM does not automatically start, please run “cdrun.exe” on the CD-ROM.≥ For details on how to use Multi-Color Dropout (MCD) Utility, refer to PIE Reference Manual and RTIV Reference
Manual.≥ The control sheets are stored as PDF files on the “Drivers & Utilities” CD-ROM provided with the scanner. For use,
print the control sheets in the same size as the document pages to be scanned. Refer to “Section 3.35 Detect Con-trol Sheet of the PIE Reference Manual”.
Contents Quick menu Applicable user
Driver install
Device Driver ±Windows 98, Windows Me, Windows 2000, Windows XP user
TWAIN ± TWAIN application user
ISIS ± ISIS application user
Applicationsinstall
RTIV ± RTIV user
Multi-Color Dropout (MCD) Utility* ± All user
View Manuals
PIE Reference Manual(TWAIN/ISIS Operating Instructions)
±All user
RTIV Reference Manual ± RTIV user
Operating Instructions ± All user
Other Control Sheet ± All user
≥ For Windows NT 4.0, Windows 2000 and Windows XP users:Make sure to log in as an administrator.
≥ For Windows NT 4.0 users:You must install the ASPI layer software that the SCSI board vender provides.
16
Drivers and Utilities CD-ROM
∫ Install device driver (Except Windows NT 4.0)1 Turn off the power of the scanner, if it is connected to your computer.
2 Insert CD-ROM to your computer.
3 Quick menu-software runs automatically.
4 Select your scanner.
5 Select Device Driver.
6 Follow the instructions on the screen.
7 Connect the scanner and turn on the power.(For SCSI connection, restart your computer.)
8 Follow the instructions of the hardware wizard to complete the installation.
∫ Install the TWAIN / ISIS driver1 Insert the CD-ROM in your computer.
2 Quick menu-software runs automatically.
3 Select your scanner.
4 Select TWAIN driver or ISIS driver.
5 Follow the instructions on the screen.
∫ Install RTIV1 Insert the CD-ROM in your computer.
2 Quick menu-software runs automatically.
3 Select your scanner.
4 Select RTIV.
5 Follow the instructions on the screen.
Even if the screen ‘Digital Signature was not found for this driver’ or ‘has not passed Windows Logo testing···’appears, continue installation.
≥ For Windows 98 usersIf “Please insert the disk labeled ‘Windows 98 CD-ROM’” is displayed, insert your Windows 98 CD-ROM and follow the instruction on the screen.
17
Drivers and Utilities CD-ROM
∫ Install the Multi-Color Dropout Utility1 Insert the CD-ROM in your computer.
2 Quick menu-software runs automatically.
3 Select your scanner.
4 Select MCD Utility.
5 Follow the instructions on the screen.
∫ View manuals1 Insert the CD-ROM in your computer.
2 Quick menu-software runs automatically.
3 Select your scanner.
4 Select a manual from the list.
5 You can view the manual using Adobe Reader.
∫ Uninstalling the device driver1 Use [Control Panel]–[Add/Remove Programs].
(In Windows XP, select [Add or Remove Programs].)
2 Select Panasonic High Speed Scanner Device Driver and click Change/Remove.
3 Follow the instructions on the screen.
≥ In case of uninstalling TWAIN/ISIS/RTIV/Multi-Color Dropout Utility, use [Control Panel]–[Add/Remove Pro-grams]. (In Windows XP, select [Add or Remove Programs].)
18
Increasing the Memory
∫ DIMM module extensionKV-S3105C is equipped with 256 MB memory on the interface board. KV-S3085 in equipped with 64MB memory onthe interface board. However, additional memory is required for scanning A3, color, double side images with 600 dpi,for example.To determine how much optional memory is required, refer to “Section 3.4 Image Type” of the PIE Reference Man-ual.
≥ JEDEC-Standard 168pin, dual in-line memory module (DIMM)≥ Nonbuffered≥ Single +3.3V±0.3V power supply≥ Frequency/ CAS Latency: 100MHz/CL=2, 133MHz/CL=2, 133MHz/CL=3≥ 64MB, 128MB, 256MB or 512MB may be used.
(Reference) DIMM module which has been evaluated and approved for use with this scanner.EDGE 128MB ModuleEDGE 256MB ModuleEDGE 512MB ModuleKingston 128MB ModuleKingston 256MB ModuleKingston 512MB Module
∫ Installing optional memory (DIMM module)Install the DIMM modules into the interface board provided in this unit.
¥ Removing interface board
1 Turn the scanner off and disconnect itfrom the electrical outlet and the inter-face cable.
Recommended DIMM
± : off position
Power switch
19
Increasing the Memory
2 Remove the four screws.
≥ These screws are used in step 2 of the“Installing the interface board.”
3 Remove the interface board by pullingon the handle.
≥ Be sure not to insert your hand into theunit when removing the interface board.Injury may result.
¥ Installing the DIMM module
Insert the DIMM module into the connector onthe interface board (1), then push it until it clicksinto place.
NOTE:≥ Be sure that the module notch is to the left side, or
the DIMM module will not be in the proper position.≥ To remove the DIMM module, pull the tabs at both
sides of the connector.≥ Do not touch any electrical components on the
surface of the board to avoid static electricity.
Handle
Tab
DIMM
Connector
Tab
20
Increasing the Memory
¥ Installing the interface board
1 Insert the interface board into the unitalong the rails and push it in firmly.
≥ Confirm that the interface board plate isfully inserted until it firmly locks in place.
2 Secure the interface board with thefour screws.
Rail
Rail
21
Repacking Instructions
It is highly recommended that you keep the original carton and ALL packing materials. If you need to transport orship your scanner, please follow these instructions:
≥ Use the original carton and all of the original packing materials.≥ Improper repacking of the scanner may result in a service charge to repair the unit.≥ The scanner should be handled in the correct (horizontal) position.
Materials Required:≥ Original scanner carton & packing materials
1 Disconnect your scanner from the electrical outlet and the interface cable.2 Remove the exit stopper and exit tray stopper from the scanner.3 Pack the scanner.
≥ To avoid damage due to the weight of the unit, the unit should be shipped with the pallet tightened by the plastic bands.
