High Bay Grow Light Solid State LuminaireINSTALLATION MANUAL

For the Following APEX Grow Light High Bay Models: (120 - 277V)

APEX600 APEX300 3C-HBGL-1P-300-12-90-G2 3C-HBGL-2P-600-12-90-G2

Hand Crafted with Pride in The United States of America

BEFORE INSTALLATION PLEASE READ ALL PRODUCT LABELS AND INSTALLATION INSTRUCTIONS

THIS PRODUCT MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN FAMILIAR WITH THE CON-STRUCTION AND OPERATION OF THIS APEX LED PRODUCT AND OF ANY HAZARDS INVOLVED

INSTALLATION MUST BE IN ACCORDANCE WITH NATIONAL ELECTRICAL CODE AND ALSO ALL RELEVANT LOCAL CODES

WARNING: IMPROPER INSTALLATION WILL VOID THIS PRODUCTS WARRANTYWARNING: TO AVOID RISK OF ELECTRICAL SHOCK DISCONNECT A/C POWER AT CIRCUIT BREAKER POWERING JUNCTION BOX BEFORE PERFORMING ANY A/C ELECTRICAL TASKSAPEX LED FIXTURE WIRING DESCRIPTION:

BLACK WIRE: AC LOAD / LINE / HOTWHITE WIRE: AC NEUTRALGREEN: AC GROUND

CAUTION: EXISTING WIRING SHOULD BE CHECKED BEFORE INSTALLATION TO INSURE CORRECT WIRING POLARITY AND CORRECTLY FUNCTIONING GROUND. EXISTING LUMINAIRE REPLACEMENT NECCESSITATES CAREFULLY REMOVING BULBS AND THEN THE LUMINAIRECAUTION: HID LAMPS AND BALLAST ARE FOUND TO CONTAIN SUBSTANCES HAZARDOUS TO HUMANS AND WILDLIFE. SOME BALLAST CONTAIN POLYCHLORINATED BIPHENYLS ALSO KNOWN AS PCB’S. PROPER HAZARDOUS MATERIAL DISPOSAL IS REQUIREDCAUTION: TO AVOID THE RISK OF ELECTRICAL SHOCK, ALLOW 5 MINUTES AFTER DISCONNECT FROM A/C POWER TO DRAIN CAPACITOR FIELD CONTAINED IN FIXTURES LED DRIVER

Thank You for your purchase of this APEX L.E.D. lighting Product. Please take a moment to read this guide and familiarize yourself with this State of the Art Solid State L.E.D. product.

Please Observe All Safety Precautions Before Installation.

CAUTION: DISCONNECT ALL A/C POWER BEFORE LIGHT FIXTURE INSTALLATION

CAUTION! SAFETY WARNINGS:

UNPACKING YOUR NEW APEX GROWLIGHT LED LIGHTING FIXTURE: CAREFULLY REMOVE LIGHTING FIXTURE FROM PACKAGING CHECKING FOR ANY SIGNS OF DAMAGEATTENTION: OPENING THIS FIXTURE IS NOT RECOMMENDED AND MAY VOID YOUR WARRANTY PLEASE NOTE IF YOU HAVE OPENED THIS HIGH BAY LIGHTING FIXTURE BY REMOV ING THE LARGE ALLEN HEAD SCREWS. PLEASE NOTE THE FOLLOWING: WHEN REAS- SEMBLING THE FIXTURE, PLEASE BE CAREFUL TO ROUTE INTERNAL EXCESS A/C CABLING AROUND AND AWAY FROM THE INTERNAL ACC SYSTEM.

All information and images are the exclusive property of Titan LED Inc. 2020 and may not be used without permission.

ATTENTION: LUMINAIRE MUST BE MOUNTED IN ACCORDANCE WITH LOCAL AND NATIONAL BUILDING CODES

MOUNTING: 1) IT IS REQUIRED TO USE THE PROPER OPTIONAL WEIGHT RATED HARDWARE TO SECURLY AND SAFELY INSTALL THIS LIGHTING FIXTURE, PLEASE SEE ILLUSTRATIONS BELOW.

PLEASE ADHERE CLOSELY TO ALL HARWARE INSTALLATION GUIDELINES TO INSURE PROPER SAFETY AND OPERATIONAL FUNCTIONS.CAUTION: PROPERTY DAMAGE, SERIOUS INJURY, AND OR DEATH MAY OCCUR FROM IMPROPER INSTALLATION OF LIGHTING FIXTURE. CAUTION: THIS PRODUCT MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THIS TITAN LED PRODUCT AND OF ANY HAZARDS INVOLVED.2) CONNECT THE A/C SUPPLY CABLE TO THE LUMINAIRES A/C CONNECTION PLATE FOUND ON THE OUTSIDE REAR CORNER OF THE APEX HIGH BAY (SHOWN BELOW) UTILIZING THE PROPRIETARY CONNECTOR CABLE IS THE OPTIMUM WAY TO POWER THIS FIXTURE. 3) AFTER INSPECTION OF PROPER AND SECURE A/C CONNECTIONS YOU CAN RESET THE MAIN POWER CIRCUIT AT THE BREAKER. YOU CAN NOW TOGGLE THE POWER SWITCH TO ON AND ENJOY YOUR NEW LIGHT.

INSTALLATION INSTRUCTIONS:

APEX GROWLIGHT L.E.D. High Bays are equipped with four eye nut cable hangers, utilizing them with the proper weight rated rope, cable or chain is mandatory to safely and properly perform suspended installations.Please see illustrations below for RECOMMENDED APEX GROWLIGHT SUSPENDED MOUNTING CABLE OPTIONS AVAILABLE FROM APEX.

ATTENTION: Heavy duty eye nuts areincluded on the top four corners of the fixture.

All information and images are the exclusive property of Titan LED Inc. 2020 and may not be used without permission.