Date post: | 10-Mar-2018 |
Category: |
Documents |
Upload: | vuongthuan |
View: | 213 times |
Download: | 1 times |
Publications No.
Issue DateINSTALLATIONINSTRUCTIONS
Accessory Application
2012 American Honda Motor Co., Inc. All Rights Reserved. AII 47334 (1208) 1 of 2908E92-T2A-1A00-90
AII 13039REMOTE CONTROL ENGINE STARTER
2013 ACCORD2 AND 4-DOOR
AUG 2012
PARTS LISTRemote Engine Starter Unit KitP/N 08E91-E54-100
Transmitter
Control unit
Antenna
ID label
Remote Control Engine Starter Attachment KitP/N 08E92-T2A-100A
(With Keyless Access System)
Engine starter harness
Control unit bracket
3 Relays
Flange nut
18 Wire ties
Wire tie with clip
6 Urethane tapes
Clip
Caution label
Fuse label
2 of 29 AII 47334 (1208) 2012 American Honda Motor Co., Inc. All Rights Reserved.
Accessory Users Information Manual
Quick Start Guide
Remote Control Engine Starter Attachment KitP/N 08E92-T2A-100B
(Without Keyless Access System)
Engine starter harness
Control unit bracket
3 Relays
Flange nut
18 Wire ties
Wire tie with clip
6 Urethane tapes
Clip
Caution label
Fuse label
Accessory Users Information Manual
Quick Start Guide
2012 American Honda Motor Co., Inc. All Rights Reserved. AII 47334 (1208) 3 of 29
TOOLS AND SUPPLIES REQUIRED
Flat-tip screwdriverPhillips screwdriverRatchet10 mm Socket10 mm Open end wrenchIsopropyl alcoholShop towelTape measureScissorsHDS/MVCIMasking tapeDiagonal cuttersRulerTapeUtility knifeThe following tools are available through the Honda Tool and Equipment Program. On the iN, click on: Service > Service Bay > Tool and Equipment Program, then enter the number under Search. Or, call 888-424-6857. Trim Tool Set (T/N SOJATP2014) Plastic Trim Tool (T/N SILTRIMTL10)
Illustration of the Remote Control Engine Starter in the Vehicle
QB20940AH
ANTENNA
3 RELAYS
3A, 20A or 40A FUSES
CONTROL UNIT
ENGINE STARTER HARNESS
INSTALLATION
1. Disconnect the negative cable from the battery.
2. Attach the ID label.
Using isopropyl alcohol on a shop towel, clean the area where the ID label will attach.
Attach the ID label to the transmitter in the area as shown.
With Keyless Memory SettingsNOTE: The remote is factory set for driver 1 remote control. To program the driver 2 remote, follow the REMOTE CONTROL ENGINE STARTER TRANSMITTER REGISTRATION instructions on ISIS.
Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers.
QB20939DH
ID LABEL
TRANSMITTER
Clean with isopropyl alcohol.
4 of 29 AII 47334 (1208) 2012 American Honda Motor Co., Inc. All Rights Reserved.
Without Keyless Memory Settings
QB32111CH
ID LABEL
TRANSMITTER
Clean with isopropyl alcohol.
3. If equipped, remove the roof console. Using a plastic trim tool, pry out and remove the
left and right lenses (four retaining tabs each). Open the sunglass holder. Remove four screws. Remove the roof console (unplug the vehicle
connectors).
With Moonroof
QB20901BX
VEHICLE CONNECTORS
ROOF CONSOLE
4 SCREWS
4 RETAINING TABS
LEFT LENS
SUNGLASS HOLDER(Open.)
4 RETAINING TABS
RIGHT LENS
2012 American Honda Motor Co., Inc. All Rights Reserved. AII 47334 (1208) 5 of 29
Without Moonroof
4. Remove two sunvisor holders by rotating them 90 counterclockwise.
QB20902AX
VEHICLE CONNECTORS
ROOF CONSOLE(if equipped)
4 SCREWS
4 RETAINING TABS
LEFT LENS
SUNGLASS HOLDER(Open.)
4 RETAINING TABS
RIGHT LENS
QB20903AX
PASSENGERS SUNVISOR HOLDER(Rotate.)DRIVERS
SUNVISOR HOLDER(Rotate.)
5. Wrap the end of a flat-tip screwdriver with tape. Locate the slot in the bracket cover, and insert the flat-tip screwdriver into the slot. Push the hook with the screwdriver.
6. While pushing in on the hook, rotate the drivers sunvisor backward about 45. Make sure the hook slides into the bracket cover.NOTE: If the hook did not stay pushed in, return the drivers sunvisor to its original position and repeat steps 5 and 6.
QB32101AX
DRIVERS SUNVISOR
FLAT-TIP SCREWDRIVER
TAPE
BRACKET COVER
Push the hook.
HOOK
While pushing in on the hook, rotate the sunvisor backward about 45.
Make sure the hook slides into the bracket cover.
FRONT
6 of 29 AII 47334 (1208) 2012 American Honda Motor Co., Inc. All Rights Reserved.
7. Remove the drivers sunvisor (unplug the vehicle connector).
8. Pull away the drivers door opening seal in the area shown.
9. Pull out on the drivers A-pillar trim to release the clips.
QB20904AX
DRIVERS SUNVISOR
FRONT
VEHICLE CONNECTOR
QB20905AX2 CLIPS
DRIVERS A-PILLAR TRIM
DOOR OPENING SEAL (Pull away.)
Pull the clip.
10. Insert a shop towel in the opening between the drivers A-pillar trim and the dashboard to prevent dropping the A-pillar clips. Take care not to damage the drivers A-pillar trim.
11. Slide up the drivers A-pillar trim to remove it from the upper clip. Carefully remove the shop towel and any clips that fell from the drivers A-pillar trim.NOTE: The upper clip will stay in the body.
QB20906AXSHOP TOWEL
DRIVERS A-PILLAR
DRIVERS A-PILLAR TRIM
QB20907AX
DRIVERS A-PILLAR TRIM
UPPER CLIP
2012 American Honda Motor Co., Inc. All Rights Reserved. AII 47334 (1208) 7 of 29
12. Remove the remaining upper clip from the drivers A-pillar.
13. Install the new clip (supplied) to the drivers A-pillar trim, but do not reinstall the trim at this time.
QB20908AX
UPPER CLIP(Discard.)
2 TABS (Push.)
DRIVERS A-PILLAR
Q0N0533AH
DRIVERS A-PILLAR TRIM
CLIP(supplied)
14. If equipped, remove the drivers dashboard under cover (turn the knob and two clips).
15. Remove the drivers dashboard lower cover (nine clips and unplug the vehicle connectors, if equipped).
QB20201AB
2 CLIPS
DRIVERS DASHBOARD UNDER COVER(if equipped) KNOB
(Turn.)
QB20202BB
DRIVERS DASHBOARD LOWER COVER
9 CLIPSVEHICLE CONNECTORS(if equipped)
8 of 29 AII 47334 (1208) 2012 American Honda Motor Co., Inc. All Rights Reserved.
16. Remove the cover (six retaining tabs). Using the ignition key, unlock the trunk lid/fuel fill door opener, then remove the key.
17. Remove one self-tapping screw from the trunk lid/fuel fill door opener cover.
QB32110AH
COVER
6 RETAINING TABS
TRUNK LID/FUEL FILL DOOR OPENER
Unlock.
KEY
SELF-TAPPING SCREW
DRIVERS DOOR SILL TRIM
18. Remove the drivers door sill trim.
4-Door: Two retaining tabs and four clips.
2-Door: Two retaining tabs and six clips.
QB20804AB
4 CLIPS
2 RETAINING TABS
DRIVERS DOOR SILL TRIM
QB32112AH
6 CLIPS
DRIVERS DOOR SILL TRIM
2 RETAINING TABS
2012 American Honda Motor Co., Inc. All Rights Reserved. AII 47334 (1208) 9 of 29
19. Pull away the door opening seal, and remove the drivers kick panel (two clips).
20. Lower the tilt lever, and release the column band (two clips). If the vehicle is equipped with keyless access system, reconnect the negative cable to the battery, then press the engine start/stop button to select the ON mode.
QB20805AB
2 CLIPS
DRIVERS KICK PANEL
DOOR OPENING SEAL (Pull away.)
QB32113AH
STEERING WHEEL
STEERING WHEEL
UPPER COLUMN COVER
COLUMN BAND
2 CLIPS
21. Turn the steering wheel 90 clockwise. Using a plastic trim tool, release the retaining tab.
22. Turn the steering wheel 180 counterclockwise. Using a plastic trim tool, release the retaining tab.
QB32114AH
UPPER COLUMN COVER
PLASTIC TRIM TOOL
STEERING WHEEL RETAINING TAB
QB32115AH
PLASTIC TRIM TOOL
RETAINING TAB
UPPER COLUMN COVER
STEERING WHEEL
10 of 29 AII 47334 (1208) 2012 American Honda Motor Co., Inc. All Rights Reserved.
23. Remove the upper column cover (two retaining tabs and two hooks).
24. Remove one self-tapping screw from the lower column cover.
QB32116AH
UPPER COLUMN COVER
2 RETAINING TABS
2 HOOKS
QB32117AHLOWER COLUMN COVER
STEERING WHEEL
SELF-TAPPING SCREW
25. Turn the steering wheel 180 clockwise, and remove the other self-tapping screw from the lower column cover.
26. Remove the lower column cover (one self-tapping screw).
27. If the vehicle is equipped with keyless access system, press the engine start/stop button to select the OFF mode. Disconnect the negative cable from the battery.
QB32118AHLOWER COLUMN COVER
SELF-TAPPING SCREW
QB32119AHSELF-TAPPING SCREW
LOWER COLUMN COVER
2012 American Honda Motor Co., Inc. All Rights Reserved. AII 47334 (1208) 11 of 29
Installing the Antenna
28. Using scissors, cut one urethane tape in half. Wrap two halves of urethane tape to the antenna cable as shown.
QB62501BK
ANTENNA
60 mm (2.4 in.)
60 mm (2.4 in.)
HALVES OF URETHANE TAPE(Do not fold the antenna cable.)
URETHANE TAPE(Cut in half.)
ANTENNA CABLE
29. Starting near the antenna end of the cable, wrap one urethane tape around the antenna cable at the measurements shown.
30. Us