Installing Standalone Statistics Collection Manager Software7-3 Cisco WAN Manager Installation Guide...

C H A P T E R

7-1Cisco WAN Manager Installation Guide

Release 15.1, Part Number OL-6259-01, Rev. A0, January 25, 2005

7Installing Standalone Statistics Collection Manager Software

This chapter provides step-by-step procedures to install the CWM Release 15.1 Statistics Collection Manager software on a standalone workstation. The CWM Release 15.1 Statistics Collection Manager Standalone (SCMSA) software installation uses InstallShield to simplify the process.

Before installing the CWM Release 15.1 SCMSA software on a standalone SCM workstation, the following software should have already been installed.

• Solaris 8 or Solaris 9 Operating System

Install either Solaris 8 or Solaris 9 according to the procedures described in Chapter 2.

• Solaris 8 or Solaris 9 patches (See the most current release notes for details of any patches that must be installed).

Installing CWM Statistics Collection Manager Standalone Installing the Standalone SCM software consist of responding to a series of screens. The screens can be regarded as being grouped into three phases.

• Initial installation phase

• Configuring Informix partitions phase (either with or without meta devices)

• Completing the installation phase

Selecting the Installation ModeTo install the CWM Release 15.1 software, perform the following steps:

Step 1 Log in to the SCMSA workstation as user root.

Note If the workstation is an Ultra 60 or other desktop system, merely log in from the keyboard. If the workstation is a Netra 20 or other rackmount system, use another Sun workstation or PC as a console and log in remotely using telnet).

Step 2 Insert the Cisco SCMSA Release 15.1 CD-ROM into the CD-ROM drive of the CWM workstation.



Chapter 7 Installing Standalone Statistics Collection Manager Software Installing CWM Statistics Collection Manager Standalone

Step 3 Enter the following commands:

# cd /cdrom/cdrom0# ls

Step 4 Check for the InstallSCMSA.sh file.

Step 5 Begin the install process by entering the following command:

# ./InstallSCMSA.sh

The following message is displayed.

Console Mode Option is recommended when you cannot connect to X Server from current terminal (See if you can open an xterm to check!)

Do you Want to Launch Installer in Console Mode? (Yes / No): [No]:

Step 6 Respond No to continue the installation using the Installshield GUI.Respond Yes to continue the installation using Console Mode Install.

Note Console Mode Install is a command line script procedure. It is an alternative to the GUI and is intended for users who do not have access to an X window device. Using Console Mode Install, the user can install SCMSA using an alpha-numeric terminal or a PC in terminal emulator mode.




Installshield GUI InstallationThe installation classes are loaded (a process that takes several minutes).

Initial Installation Phase

The SCMSA Installation Welcome window is displayed, as shown in Figure 7-1.

Figure 7-1 SCMSA Installation Welcome Window

Step 7 Click Next on the Welcome window to continue. The license agreement window is displayed as shown in Figure 7-2.




Figure 7-2 SCMSA License Agreement Window

Step 8 Click the “I accept” button and then click Next.The Install Standalone Stats Collector or Standalone Stats Manager window, Figure 7-3, is displayed.




Figure 7-3 Install Standalone Stats Collector or Standalone Stats Manager Window

Step 9 Choose one of the two options displayed in the window.

Note See Appendix A for more details on possible SCM standalone configurations.

Step 10 After choosing an option, click Next




Figure 7-4 Information about the Upgrading procedure window

Step 11 Choose No to the upgrade question and then click Next.

The Raw Partition window is displayed as shown in Figure 7-5.




Figure 7-5 Raw Partition Window

Step 12 Choose Yes if the Informix log is to have its own separate raw partition, otherwise Choose No.

Step 13 Click Next.

The Select the Raw Partition window is displayed, as shown in Figure 7-6.

Note This window is displayed only if the user responds Yes to the separate raw partition for the Informix log.




Figure 7-6 Select the Raw Partition Window

Step 1 Choose a raw partition for the Informix log.

Step 2 Click Next.

Step 3 The Meta Devices window is displayed as shown in Figure 7-7.




Figure 7-7 Meta Devices Window

Step 4 If you have no meta devices, accept the default No and click Next.

Note A meta device is a virtual device created by concatenating or striping disk partitions (this is done usually to improve flexibility or performance). The use of meta devices usually requires volume management software found in Solaris (for example, Solstice Sun Disk Suite) or via third party vendors, such as Veritas.

The Multiple Disk Configuration for Informix window is displayed, as shown in Figure 7-8.

Note The window shown in Figure 7-8 is displayed only if there are two raw partitions available and the user has not selected a separate partition of the physical log OR if there are at least three raw partitions available.




Figure 7-8 Multiple Disk Configuration for Informix Window

Step 5 At the Multiple Disk Configuration for Informix window, if you have one disk accept the default No and click Next. If you have multiple disks, click on the Yes radio button.

Note In this context, the term disk refers to a disk partition (or slice).

Step 6 Click Next to continue.




Configuring Informix Partitions PhaseConfiguring Informix partitions consists of eight different procedures of which only one needs to be performed. Which procedure the user performs depends upon the responses the user has made to the questions in the previous phase.

Choose the procedure which corresponds to your previous answers to the following questions.

– Do you want the Informix log to have its own raw partition?

– Do you use disk striping (meta-devices) for database partitions?

– Are you using multiple disks (partitions) for Informix?

Proceed to one of the following procedures that corresponds to your answers.

In each of the procedures, the user is asked to specify details about the allocations of Informix partitions.

Note Informix uses the disk space available to it to construct three database spaces. If the user specifies multiple disks for Informix, the installation procedure requires the user to specify which database space is to be allocated to which partition. Note that the datadbs database space will be the largest and should be allocated accordingly.

The procedures are described in the following sequence.

1. No Meta Devices, No multiple disks, No separate raw log partition

2. No Meta Devices, No multiple disks, Yes separate raw log partition

3. No Meta Devices, Yes multiple disks, No separate raw log partition

4. No Meta Devices, Yes multiple disks, Yes separate raw log partition

5. Yes Meta Devices, No multiple disks, No separate raw log partition

6. Yes Meta Devices, No multiple disks, Yes separate raw log partition

7. Yes Meta Devices, Yes multiple disks, No separate raw log partition

8. Yes Meta Devices, Yes multiple disks, Yes separate raw log partition




1. No Meta Devices, No multiple disks, No separate raw log partition

The Select the Raw Partition for CWM Database window is displayed, as shown in Figure 7-9.

Figure 7-9 Select the Raw Partition for CWM Database Window

This window displays only the raw partitions available to Informix.

Step 1 Select the single raw partition to be used.

Step 2 Proceed to the Completing the Installation section later in this chapter.




2. No Meta Devices, No multiple disks, Yes separate raw log partition


Note If only one raw partition is available for the databases, this window is skipped.


Step 1 Select the partition(s) that are to be used for the Informix database.


3. No Meta Devices, Yes multiple disks, No separate raw log partition






Step 1 Select the partitions for the rootdbs and datadbs.

Note Select only one partition for rootdbs. Rootdbs and datadbs cannot be assigned the same partitions. If there are enough raw partitions, datadbs can be assigned multiple partitions.


4. No Meta Devices, Yes multiple disks, Yes separate raw log partition






Step 1 Select the partitions for the rootdbs and datadbs.

Note Select one partition for rootdbs. Rootdbs and datadbs cannot be assigned the same partitions.


5. Yes Meta Devices, No multiple disks, No separate raw log partition






Step 1 Enter the paths and sizes of the meta devices.In this release of CWM, the database name cannot be changed, accept the default name of stratacom.





6. Yes Meta Devices, No multiple disks, Yes separate raw log partition

The Select the Path for CWM Database window is displayed, as shown in Figure 7-14.

Figure 7-14 S.elect the Raw Partition for CWM Database Window


Step 2 Proceed to the Completing the Installation later in this chapter.




7. Yes Meta Devices, Yes multiple disks, No separate raw log partition




Step 2 Click Next.

Step 3 Proceed to the Completing the Installation later in this chapter.




8. Yes Meta Devices, Yes multiple disks, Yes separate raw log partition




Step 2 Proceed to the following Completing the Installation section.




Completing the InstallationWhen the Configuring Informix Partitions phase has been completed, the CWM FTP Information Window is displayed as shown in Figure 7-17.

Figure 7-17 CWM FTP Information Window

Step 1 At the CWM FTP Information window, enter the user name (default “svplus”) and the password of the user on the machine.

Note In this release, the user name of “svplus” must be used and cannot be changed.

After entering the FTP user name and password, click Next.

If you are installing SSM, the SCM Control Server window is displayed as shown in Figure 7-18. Otherwise this next window is skipped.




Figure 7-18 SCM Control Server Window

Step 2 Enter the name or IP address of the CWM Server machine in which the SCM Control Server is located. Click Next.

The CORBA Communications Options window is displayed as shown in Figure 7-19.




Figure 7-19 CORBA Communications Options

This window provides the user with four choices of how the server identifies itself for CORBA (Orbix) communications. These choices are:

• The CWM Server host name including a domain name

• The CWM Server host name without a domain name

• The IP address of the CWM server

• A user specified address

Select the method is use for your CWM network and click Next.

If the user selects “Host with DNS domain name”, the user is then asked to specify the domain name as shown in Figure 7-20. If the user selects “Use specified IP Address”, the user is then asked to specify the IP address as shown in Figure 7-21.




Figure 7-20 Enter the Domain Name Window




Figure 7-21 Enter IP Address Window

Enter the Domain Name or IP Address as appropriate and click Next.

This domain name and IP address information allows the CWM client workstations access to the database. Also ensure that the workstation and the domain are reachable. You can enter the ping command to test this.

The Installation Confirmation screen is displayed.




Figure 7-22 Installer Confirmation Window

Step 3 If the information in the Confirmation window is correct, click Next. If it is not correct, click Back to the appropriate window and correct the wrong settings.

When Next is clicked, the Installation Progress Window is displayed as shown in Figure 7-23.




Figure 7-23 Installation Progress Indicator

After a short while, the User/Group message is displayed as shown in Figure 7-24.

Figure 7-24 User/Group Message

Step 4 Click Yes.

If the CWM system was installed previously, a message appears telling the user that files already exist and permission is requested to overwrite the files with new files. This message is shown in Figure 7-25.

Figure 7-25 Copy Files Message

Step 5 Click Yes to All.

After a some time, an Install Log window is also displayed (see Figure 7-26). This log provides on-the-screen messages indicating events during the installation process.




The SCMSA install log file is called scmsaexecinstall.Log and is located in the /usr/user/svplus/install directory.

Figure 7-26 Install Log

A dialog box displays informing you that the installation is complete, as shown in Figure 7-27.

Figure 7-27 Installation Complete Window

Step 6 Click Finish on the dialog box.

The software installation process is completed. The Install Shield window closes.

The first time (and only the first time) that SCMSA is installed, the system displays a message stating that the kernel is changed.

Step 7 Click OK to reboot the system.

The reboot sequence aligns the cylinders of your hard disks and gracefully shuts down the Solaris operating system.




The OK prompt is displayed.

Step 8 Push the CD-ROM eject button on the CD-ROM drive to eject the CD.

Note After installing or upgrading SCMSA on a machine that has not previously had CWM installed, it is possible that an account in the name svplus has not been established. If this so, establish an svplus account manually.

Note When a standalone statistics collection machine has been installed, the statsparser.conf and SCMGateways.conf files may need to be configured. Refer to Appendix for details.

Console Mode Installation If you enter Yes to run in Console Mode, the following panel is displayed

You've chosen to Launch Installer in Console Mode

Loading the installation classes. This may take a few minutes................................................................................................................................................................................................................................................................................................................................................................................InstallShield Wizard

Initializing InstallShield Wizard...

Searching for Java(tm) Virtual Machine............Running InstallShield Wizard...

After a few seconds the Initial Installation phase starts

Making Selections during Console Mode Upgrade

The Console Mode procedure consists of responding to a series of questions. The user is asked either to select an item from a list or to enter data (for example, a database path or a disk size).

Selecting an Item from a List.

When a list is displayed, each item in the list has an item number. Further, one item in the list is already selected as indicated by an X. For example:

Choose the Raw partition for Informix Physical Log:

[X] 1 - /dev/rdsk/c1t0d0s7 ( 4000 MB)




[ ] 2 - /dev/rdsk/c1t1d0s0 ( 2048 MB) [ ] 3 - /dev/rdsk/c1t1d0s1 ( 2048 MB) To select a choice enter its number, or 0 when you are finished [0]:

The above example lists three disk partitions from which the user must select one. These items are numbered as 1, 2, and 3 and the first is already selected as indicated by [X].

The user can accept the already selected item or select another item by typing its number followed by the Enter key (in which case the list is displayed again but with the [X] against the selected item).

When the [X] is shown against the correct item (either in the initial display or after the user has selected another item), the user should press 0 followed by the Enter key. The following message is then displayed.

Press 1 for Next panel, 2 for Previous panel, 3 to Cancel or 4 to Redisplay [1]

The user then press 1, 2, 3, or 4 (as appropriate) followed by the Enter key. Normally this will be the 1 key to progress to next step in the upgrade process.

Entering Data

When requested enter the data and press the Enter key. If you want to change the entered data, press 1 and the Enter key and then start over. When the enter data are correct, press 0 and the Enter key.

Initial Install Phase

Step 1 The Welcome message is displayed.

-------------------------------------------------------------------------------

Welcome to the Cisco Wan Manager installation program. Click Cancelat any time to quit the installation. Press Next to continue the installation.

Press 1 for Next panel, 3 to Cancel or 4 to Redisplay [1]

-------------------------------------------------------------------------------

Press 1 then Enter to display the next message

Step 2 The Readme message is displayed.

-------------------------------------------------------------------------------

Cisco Wan Manager 15.1.0 Copyright (c) 2004 Cisco Systems, Inc. Allrights reserved. This software product is copyrighted and all rights arereserved by Cisco Systems, Inc. Cisco Systems, Inc. reserves the right to makeperiodic modifications to this product without obligation to notify any personor entity of such revision. Copying, duplicating, selling, or otherwisedistributing any part of this product without the prior written consent of anauthorized representative of Cisco Systems, Inc. is prohibited. IPX, IGX8400,BPX8600, MGX8220, MGX8850, MGX8950 and FastPacket are registered trademarksand Cisco WAN Manager is a trademark of Cisco Systems, Inc.

Please choose from the following options:

[X] 1 - I accept the terms of the license agreement. [ ] 2 - I do not accept the terms of the license agreement.

To select a choice enter its number, or 0 when you are finished [0]:





-------------------------------------------------------------------------------

a. To accept the license terms, press 0 then Enter.

b. Press 1 then Enter to display the next message.

Step 3 The Manager/Collector Selection window is displayed.

-------------------------------------------------------------------------------

Which one of the following do you want to install? [ ] 1 - Standalone Stats Collector [X] 2 - Standalone Stats Manager

To select a choice enter its number, or 0 when you are finished [0]: 0

Press 1 for Next panel, 2 for Previous panel, 3 to Cancel or 4 to Redisplay [1] 1-------------------------------------------------------------------------------

a. Select Stats Collector or Stats Manager by pressing 1 or 2.

b. Press 0 then Enter.

c. Press 1 then Enter to display the next message.

Step 4 The Upgrading message is displayed.

-------------------------------------------------------------------------------

Are You Upgrading Cisco SCMSA? [ ] 1 - Yes [X] 2 - No



-------------------------------------------------------------------------------

a. To select a new install (not upgrading), either press 0 (to accept the default) or press 2 and then press 0.

b. Press 1 then Enter to display the next panel.

Step 5 The Physical Log on separate partition panel is displayed.

-------------------------------------------------------------------------------

Do you want Informix Physical Log on a separate Raw Partition?

[ ] 1 - Yes [X] 2 - No



-------------------------------------------------------------------------------

c. To select no separate paratition, either press 0 (to accept the default) or press 2 then press Enter.




d. To select a separate partition for the Informix Physical Log, press 1 then Enter. If the correct option is selected, press 0 then Enter.

e. Press 1 then Enter to display the next panel.

Step 6 The Select Partition for Physical Log panel is displayed

Note If the user selected no separate partition in the previous step, this panel is skipped.

-------------------------------------------------------------------------------

Choose the Raw partition for Informix Physical Log :

[X] 1 - /dev/rdsk/c1t0d0s7 ( 4000 MB) [ ] 2 - /dev/rdsk/c1t1d0s0 ( 2048 MB) [ ] 3 - /dev/rdsk/c1t1d0s1 ( 2048 MB) [ ] 4 - /dev/rdsk/c1t1d0s3 ( 2048 MB) To select a choice enter its number, or 0 when you are finished [0]:


-------------------------------------------------------------------------------

This panel displays all the raw partitions that are available for the Informix Physical Log.

a. To select a raw partition, either press 0 (to accept the default) or press a number of the desired partition and then press Enter. If the correct partition is selected, press 0 then Enter.

b. Press 1 then Enter to display the next panel.

Step 7 The Meta Devices panel is displayed.

Note A meta device is a virtual device created by concatenating or striping disk partitions (this is done usually to improve flexibility or performance). The use of meta devices usually requires volume management software found in Solaris (for example, Solstice Sun Disk Suite) or via third party vendors, such as Veritas.

-------------------------------------------------------------------------------

Do you use Disk-stripping (meta-devices) for database Partitions? [ ] 1 - Yes [X] 2 - No



-------------------------------------------------------------------------------

a. To select no meta devices, either press 0 (to accept the default) or press 2 then press Enter. If the correct option is selected, press 0 then Enter.

b. To select the use of meta devices, press 1 then press Enter. If the correct option is selected, press 0 then Enter.




c. Press 1 then Enter to display the next panel.

Step 8 The Multiple Disks panel is displayed.

Note If the user specified a separate partition for the physical log and the system has only two raw partitions available, the answer to the multiple disk configuration is assumed to be No and this panel is skipped

-------------------------------------------------------------------------------

Do you want to use Multiple Disk configuration for Informix database?

[ ] 1 - Yes [X] 2 - No



-------------------------------------------------------------------------------

a. To select no multiple disks, either press 0 (to accept the default) or press 2 then press Enter.

b. To select the use of multiple disks, press 1 then press Enter.

c. When the correct option is selected, press 0 then Enter.

d. Then press 1 then Enter to display the next panel.

Configuring Informix Partitions Phase

Configuring Informix partitions consists of eight different procedures of which only one needs to be performed. Which procedure the user performs depends upon the responses the user has made to the questions in the previous phase.

Select the procedure which corresponds to your previous answers to the following questions.

– Do you want the Informix log to have its own raw partition?

– Do you use disk striping (meta-devices) for database partitions?

– Are you using multiple disks (partitions) for Informix?

Proceed to one of the following procedures that corresponds to your answers.

In each of the procedures, the user is asked to specify details about the allocations of Informix partitions.

Note Informix uses the disk space available to it to construct three database spaces. If the user specifies multiple disks for Informix, the installation procedure requires the user to specify which database space is to be allocated to which partition. Note that the datadbs database space will be the largest and should be allocated accordingly.

The procedures are described in the following sequence.

1. No Meta Devices. No Multiple Disks, No Separate Raw Log Partition




2. No Meta Devices. No Multiple Disks, Yes Separate Raw Log Partition

3. No Meta Devices. Yes Multiple Disks. No Separate Raw log partition

4. No Meta Devices. Yes Multiple Disks. Yes Separate Raw log partition

5. Yes Meta Devices. No Multiple Disks. No Separate Raw Log Partition

6. Yes Meta Devices. No Multiple Disks. Yes Separate Raw Log Partition

7. Yes Meta Devices. Yes Multiple Disks. No Separate Log Partition

8. Yes Meta Devices. Yes Multiple Disks. Yes Separate Log Partition

1. No Meta Devices. No Multiple Disks, No Separate Raw Log Partition

The following panel is displayed.

-------------------------------------------------------------------------------

Choose the Raw Partition(s) for Informix: rootdbs

[X] 1 - /dev/rdsk/c1t1d0s0 ( 2048 MB) [ ] 2 - /dev/rdsk/c1t1d0s1 ( 2048 MB) [ ] 3 - /dev/rdsk/c1t1d0s3 ( 2048 MB)



-------------------------------------------------------------------------------

This window displays only the raw partitions available to Informix.

Step 1 Press the number corresponding to raw partition to be used and then press Enter. If the correct partition is selected, press 0 then Enter.

Step 2 Then press 1 then Enter to proceed to the Completing the Installation section later in this chapter.

2. No Meta Devices. No Multiple Disks, Yes Separate Raw Log Partition

The following panel is displayed.

-------------------------------------------------------------------------------

Choose the Raw Partition(s) for Informix: rootdbs

[X] 1 - /dev/rdsk/c1t1d0s0 ( 2048 MB) [ ] 2 - /dev/rdsk/c1t1d0s1 ( 2048 MB) To select a choice enter its number, or 0 when you are finished [0]:


-------------------------------------------------------------------------------

This window displays only the raw partitions available to Informix. Notice that the separate partition previously selected for the Informix physical log is no longer available and is not displayed.




Step 1 Press the number corresponding to raw partition to be used and then press Enter. If the correct partition is selected, press 0 then Enter.


3. No Meta Devices. Yes Multiple Disks. No Separate Raw log partition

The following panel is displayed

-------------------------------------------------------------------------------

Choose the Raw Partition for Root Dabs

[X] 1 - /dev/rdsk/c1t0d0s7 ( 4000 MB) [ ] 2 - /dev/rdsk/c1t1d0s0 ( 2048 MB) [ ] 3 - /dev/rdsk/c1t1d0s1 ( 2048 MB) To select a choice enter its number, or 0 when you are finished [0]: 1

Step 1 Press the number corresponding to Root Dbs partition to be used and then press Enter. If the correct partition is selected, press 0 then Enter.The following panel is displayed.

[ ] 2 - /dev/rdsk/c1t1d0s0 ( 2048 MB) [ ] 3 - /dev/rdsk/c1t1d0s1 ( 2048 MB) [ ] 4 - /dev/rdsk/c1t1d0s3 ( 2048 MB) [X] 5 - /dev/rdsk/c1t1d0s4 ( 2048 MB) To select a choice enter its number, or 0 when you are finished [0]:

Press 1 for Next panel, 2 for Previous panel, 3 to Cancel or 4 to Redisplay [1] -------------------------------------------------------------------------------

Step 2 Press the number corresponding to Datadb partition to be used and then press Enter. If the correct partition is selected, press 0 then Enter.


4. No Meta Devices. Yes Multiple Disks. Yes Separate Raw log partition


-------------------------------------------------------------------------------

Choose the Raw Partition for Root Dbs

[X] 1 - /dev/rdsk/c1t0d0s7 ( 4000 MB) [ ] 2 - /dev/rdsk/c1t1d0s0 ( 2048 MB) [ ] 3 - /dev/rdsk/c1t1d0s1 ( 2048 MB) [ ] 4 - /dev/rdsk/c1t1d0s3 ( 2048 MB) [ ] 5 - /dev/rdsk/c1t1d0s4 ( 2048 MB)





Step 1 Press the number corresponding to Root Dbs partition to be used and then press Enter. If the correct partition is selected, press 0 then Enter.

Press 1 then Enter, The following panel is displayed

Choose the Raw Partition for Data Dbs

[ ] 2 - /dev/rdsk/c1t1d0s0 ( 2048 MB) [ ] 3 - /dev/rdsk/c1t1d0s1 ( 2048 MB) [ ] 4 - /dev/rdsk/c1t1d0s3 ( 2048 MB) [X] 5 - /dev/rdsk/c1t1d0s4 ( 2048 MB) To select a choice enter its number, or 0 when you are finished [0]:

Press 1 for Next panel, 2 for Previous panel, 3 to Cancel or 4 to Redisplay [1] -------------------------------------------------------------------------------

Step 2 Press the number corresponding to Datadb partition to be used then press Enter. If the correct partition is selected, press 0 then Return.


5. Yes Meta Devices. No Multiple Disks. No Separate Raw Log Partition


-------------------------------------------------------------------------------

Enter the Complete path of the meta device for the informix database rootdebases

[]

Step 1 Enter the path of the meta device and press the Enter key.The following panel is displayed

Enter the Size in MB

[]


-------------------------------------------------------------------------------

Step 2 Enter the size of the database in megabytes and press the Enter key.





6. Yes Meta Devices. No Multiple Disks. Yes Separate Raw Log Partition


-------------------------------------------------------------------------------

Enter the Complete path of the meta device for the informix database rootdbspace

[]

Step 1 Enter the path of the meta device and press the Enter key.The following panel is displayed


[]


-------------------------------------------------------------------------------

Step 2 Enter the size of the database in megabytes and press the Enter key.


7. Yes Meta Devices. Yes Multiple Disks. No Separate Log Partition


-------------------------------------------------------------------------------


[]

Step 1 Enter the path of the meta device for the Informix database root and press the Enter key.The following panel is displayed


[]

Step 2 Enter the size of the Informix database root in megabytes and press the Enter key..

Enter the Complete path of the meta device for the informix database CWMdbspace

[]

Step 3 Enter the path of the meta device for the Informix database CWM dbspace and press the Enter key.The following panel is displayed





[]

Step 4 Enter the size of the Informix database CWM dbspace in megabytes and press the Enter key.The following panel is displayed.

[]

Enter the Complete path of the meta device for the informix database logdbs

[]


[]

Step 5 Enter the path of the meta device for the Informix database logdbs and press the Enter key.The following panel is displayed


[]


Step 6 Enter the size of the Informix database CWM dbspace in megabytes and press the Enter key.


8. Yes Meta Devices. Yes Multiple Disks. Yes Separate Log Partition


-------------------------------------------------------------------------------


[]

Step 1 Enter the path of the meta device for the Informix database root and press the Enter key.The following panel is displayed


[]

Step 2 Enter the size of the Informix database root in megabytes and press the Enter key..

Enter the Complete path of the meta device for the informix database CWMdbspace

[]




Step 3 Enter the path of the meta device for the Informix database CWM dbspace and press the Enter key.The following panel is displayed


[]

Step 4 Enter the size of the Informix database CWM dbspace in megabytes and press the Enter key.The following panel is displayed.

[]

Enter the Complete path of the meta device for the informix database logdbs

[]


[]

Step 5 Enter the path of the meta device for the Informix database logdbs and press the Enter key.The following panel is displayed


[]


-------------------------------------------------------------------------------

Step 6 Enter the size of the Informix database CWM dbspace in megabytes and press the Enter key.

Step 7 Press 1 then Enter to proceed to the Completing the Installation section later in this chapter.

Completing the Installation

When one of the eight Informix partition phase procedures has been completed, the FTP Information panel is displayed automatically.

-------------------------------------------------------------------------------

FTP User name

[svplus]

FTP Password

:ReEnter the Password: Press 1 for Next panel, 2 for Previous panel, 3 to Cancel or 4 to Redisplay [1]

-------------------------------------------------------------------------------




Step 1 Perform the following sub-steps.

a. Leave the FTP User name as the default value of ‘svplus’.

b. Enter the password to be used for FTP and press the Enter key.

c. Repeat the password and again press the Enter key.

d. Press 1 then Enter to proceed to the next panel.

If the SSM is being installed, the SCM Control Server Panel is displayed. If the SSC is being installed, this panel is skipped and the Orbix Domain Name panel is displayed.

-------------------------------------------------------------------------------

Please enter the machine which has the SCM Control Server

[]

Press 1 for Next panel, 2 for Previous panel, 3 to Cancel or 4 to Redisplay [1] 1

-------------------------------------------------------------------------------


a. Enter a name of IP address of the CWM server in which the SCM server is located.

b. Press 1 then Enter to proceed to the next panel.

Step 3 The CORBA Communication Option panel is displayed

-------------------------------------------------------------------------------

Please choose one of the following options for CORBA communication: [X] 1 - Host with DNS domain setup [ ] 2 - Host without DNS domain [ ] 3 - Use machine IP Address [ ] 4 - Use specified IP Address


This window provides the user with four choices of how the server identifies itself for CORBA (Orbix) communications. These choices are:

• The CWM Server host name including a domain name

• The CWM Server host name without a domain name

• The IP address of the CWM server

• A user specified address

Perform the following sub-steps.

a. Select the method in use for your CWM network and press 0 and Return.

b. Press 1 then Enter to proceed to the next panel.

c. If the user selects “Host with DNS domain name”, the user is then asked to specify the domain name

-------------------------------------------------------------------------------

Enter the Domain Name to be used by Orbix (eg:cisco.com)

[]

Press 1 for Next panel, 2 for Previous panel, 3 to Cancel or 4 to




Redisplay [1] 2

-------------------------------------------------------------------------------

Enter the Domain Name and press the Return key, Press 1 for the next panel.

d. If the user selects “Use specified IP Address”, the user is then asked to specify the IP address.

-------------------------------------------------------------------------------

Please enter the IP Address for Orbix communication:

[172.29.52.25]

Press 1 for Next panel, 2 for Previous panel, 3 to Cancel or 4 to Redisplay [1] 1

-------------------------------------------------------------------------------

Enter the IP Address and press the Return key, Press 1 for the next panel.

The Installation Preview panel is displayed.

-------------------------------------------------------------------------------

SCMSA will be installed in the following location:/usr/users/svpluswith the following features:WandestClientSCMSAfor a total size: 962MB

Press 1 for Next panel, 2 for Previous panel, 3 to Cancel or 4 to Redisplay [1]-------------------------------------------------------------------------------


a. Check the information. If not correct, use the 2 key to go back to a previous panel so that the correction can be made.

b. When the displayed information is correct, press 1 then Enter to proceed to the next panel.

The Installation Progress panel is displayed.

-------------------------------------------------------------------------------

Running in Console Mode. Do tail -f in a separate window on log file for status.Log file is /usr/users/svplus/install/cwmexecInstall.Log

Installing SCMSA ... Please wait.

|-----------|-----------|-----------|------------|0% 25% 50% 75% 100%|||||||||||||||||||||||||||||||||||||||||||||||||Committing changes to the Solaris Product Registry.|.........DONE

Creating uninstaller...

-------------------------------------------------------------------------------




The progress bar indicates the progress of the installation. When the installation is complete, the Installation Complete is displayed.

-------------------------------------------------------------------------------The InstallShield Wizard has successfully installed SCMSA. Choose Finish to exit the wizard.

Press 3 to Finish or 4 to Redisplay [3]

-------------------------------------------------------------------------------

Step 5 Press 3 then Enter to complete the installation.




Date post:	03-Mar-2021
Category:	Documents
Upload:	others
View:	1 times
Download:	0 times

Installing Standalone Statistics Collection Manager Software7-3 Cisco WAN Manager Installation Guide...

Documents