1/10 SCALE ELECTRIC FORMULA CAR
INSTRUCTION MANUAL
SAFETY PRECAUTIONSPlease read this instruction manual carefully before assembling and operating this model.• This product is an authentic radio controlled model, not a toy.• To enjoy this model to the fullest, properly assemble the model before operating it, perform maintenance after each operating session, and replace some parts with optional parts.• Improper usage of rechargeable batteries may make the electric current too high, which may cause heat, liquid leakage, and or fire. Follow the battery and charger
instruction manuals and use both items safely.
In order to operate the model safely, adhere to following instructions. Hear are some possibilities of significant damage to life and or body, if the following explanation.
• Before you start assembling this model, read this instruction manual thoroughly. If you are not used to assembling a model, seek advice from people who have enough experience in assembling models and assemble this model correctly.
• This product includes many small or sharp parts, so be careful with them and keep them out of the reach of small children.• All tools including knives, pliers and drivers require careful handling to avoid injury.• Painting must be done only in a well-ventilated area.• With weak or dry batteries, the radio will not be able to control the model and the model may become out of control and cause a serious accident. Always be aware
how much power is left in radio batteries and charge or replace them with new ones if necessary. • Don’t operate the model on anything except the track designed exclusively for it.• Be sure that you are not operating this model at a place where there is another model running at the same frequency as yours. Failure to do so will cause the models to lose control.• When the model is moving strangely, stop the model immediately and find out the reason. Don't operate the model again until the problem is solved. To continue
operating the model without solving the problem may lead to further trouble or unforeseen accidents! • Don't put fingers or any objects inside the rotating or moving parts! • Always operate the model attached with a body shell (not included in the kit).• Check all screws and nuts on a regular basis for looseness.• To avoid damage, don't install any optional parts not made by INFINITY in this model or modify the model.
WARNING! PROHIBITED
ITEMS REQUIRED FOR OPERATION TOOLS REQUIRED1. Transmitter and Receiver (2ch)2. Low-Profile Steering Servo 3. Speed Controller4. 540 size Motor5. LiPo Battery (7.4V, Hard plastic case)6. LiPo Battery Charger7. Tires, Wheels and Inserts for 1/10 Formula car.
8. 1/10 Formula Body Shell9. 1/10 Formula Wing10. Polycarbonate Paint11. 64 Pitch Pinion Gear12. Silicone Oils13. Graphite Grease14. Ball DIff Grease
1. Hex Wrenches (1.5mm / 2.0mm / 2.5mm / 3.0mm)2. Box Driver (5.0mm / 5.5mm / 7.0mm)3. Needle Nose Pliers4. Nippers for plastic parts5. Sharp Hobby Knifes6. Scissors7. Turnbuckle wrench (4.0mm)
8. Body Reamer
安全のための注意事項組み立て、走行の前に必ずお読みください。• この商品は本格的な無線操縦模型です。玩具ではありません。• この商品を楽しむために走行前の組み立てや、走行後のメンテナンス、オプションパーツへの交換などを行う必要があります。• 充電式の電池は使い方を誤ると大きな電流が流れ、発熱や液漏れ、発火の可能性があります。バッテリー及び充電器の説明書にもとづき安全に使用してください。
この商品を安全に取り扱うために下記の事項を必ずお守りください。この説明を守らないと生命や身体に重大な被害が発生する可能性がある危険を示します。
• 組み立て前に必ず説明書を最後までお読みください。また、組み立てに不慣れな方は模型をよく知っている人にアドバイスを受け、確実に組み立ててください。• 小さな部品や尖った部品がありますので十分注意してください。また、小さなお子様のいる場所での作業、保管は避けてください。• カッターやニッパー、ドライバーなど工具の取り扱いには十分注意してください。• 塗装する場合は室内の換気に十分注意し作業を行ってください。• 送信機のバッテリーが減ってくるとコントロールできなくなり、暴走や衝突の原因になります。大きな事故の原因となります。送信機のバッテリー残量を常に確認し、必要であればバッテリー交換、充電を行ってください。
• 専用サーキット以外での走行させないでください。• 同じ周波数の近くでは走行させないでください。混信により、コントロール不能で暴走の原因になります。• 車の動きがおかしい時はすぐに走行を中止して原因を調べてください。原因不明のまま走行させると、思わぬ故障や事故の原因になります。• 回転している部分に指や物を入れないでください。• 走行時は必ずボディ(別売)を装着してください。• 定期的に各部のビスがゆるんでいないかチェックしてください。• インフィニティ製オプションパーツ以外の組み込みや車体の改造はしないでください。故障の原因となります。
キットの他に必要なもの 組み立てに必要な工具1. 2チャンネル送受信機2. ロープロファイルタイプステアリングサーボ3. スピードコントローラー4. 540サイズモーター5. 走行用Li-Poバッテリー(7.4V、角型プラスチックケース)6. 走行用Li-Poバッテリー充電器7. 1/10フォーミュラーカー用タイヤ&ホイール及びインサート
8. 1/10フォーミュラーカーボディ9. 1/10フォーミュラーカー用ウイング10.ボディ塗装用塗料11.64ピッチピニオンギヤ12.ショックオイル13.潤滑用グリス14.ボールデフグリス
1. 六角レンチ(1.5mm,2.0mm,2.5mm,3.0mm)2. ボックスドライバー(5.0mm,5.5mm,7.0mm)3. ラジオペンチ4. プラスチック用ニッパー5. ホビーナイフ6. ハサミ7. ターンバックルレンチ(4.0mm)
8. ボディリーマー
警告 禁止
4
F039Graphite Front Upper Armカーボンフロントアッパーアーム
F011Pivot Ball Bushingピボットボールブッシュ
F010
F012
F012
x6
F010Alu 6mm Pivot Ballアルミ6mmピボットボール
x6
F012Pivot Ball Bushing O-RingピボットボールブッシュOリング
x6
ピボットボールがスムーズに動くように調整してください。
Ensure pivot balls are free and have smooth movement.
Assemble both L&R.左右作る。L/R
F012
R
L
Top
Bottom
BAG A 1
5
Graphite Front Upper Armカーボンフロントアッパーアーム
x2
ピボットボールがスムーズに動くように調整してください。
Ensure pivot balls are free and have smooth movement.
NOTE DIRECTION向きに注意してください。
F040Graphite Front Lower Armカーボンフロントロアアーム
F004Steering Stopper Setステアリングストッパーセット
M3x6mm Button Head Screwボタンヘッドスクリュー
Assemble both L&R.左右作る。L/R
F010
F011
F012M3x6mm Button Head Screw
ボタンヘッドスクリュー
x2
F010Alu 6mm Pivot Ball, Shortアルミ6mmピボットボール、ショート
x2
F012Pivot Ball Bushing O-RingピボットボールブッシュOリング
x2
R
L
Top
Bottom
2
6
F004
F004
F001Monocoque Chassis Setモノコックシャーシセット
M3x10mm Button Head Screw ボタンヘッドスクリュー
M3x10mm Button Head Screw ボタンヘッドスクリュー
x4
3
7
M3x6mm Flat Head Screw フラットヘッドスクリュー
M3x6mm Flat Head Screw フラットヘッドスクリュー
x4
4
8
BAG BBALLBEARINGS
F007
F002Steering Arm / Mount Setステアリングアーム /マウントセット
F002F002
R0204
Ball Bearing 3x6x2.5mmボールベアリング
F018Alu Steering Postアルミステアリングポスト
F007
F002
R0204R0204
Ball Bearing 5x8x2.5mmボールベアリング
x4
Ball Bearing 3x6x2.5mmボールベアリング
x2
M3x10mm Flat Head Screw フラットヘッドスクリュー
M3x10mm Flat Head Screw フラットヘッドスクリュー
x2
M3x6mm Button Head Screw ボタンヘッドスクリューM3x6mm Button Head Screw
ボタンヘッドスクリュー
x2
F007Alu Ball End 4.3x11.8mmアルミボールエンド
x3
ネジを締め込んだところから1/3 回転緩めて、ステアリングアームがスムーズに動くようにします。
Tighten the screws gently but fully, and then loosen 1/3 turn so the dual steering arms move freely.
NOTE DIRECTION向きに注意してください。
5
SANWA FUTABA
9
≦ 11mm
切り落とす
F002F002
F002
Washer M3ワッシャー
F006
F047Servo Saver Setサーボセイバーセット
F047Servo Saver Spring t=0.8サーボセイバースプリング
F047Servo Saver Spring t=0.6サーボセイバースプリング
F047
F047
Washer M3ワッシャー
x3
SANWA, KO FUTABA, SAVOXPower HD
3 4
Choose depending on your servo brand.使用するサーボに合わせて選びます。
F006Alu Ball End 4.3x10mmアルミボールエンド
x1 M3x8mm Button Head Screw ボタンヘッドスクリュー
M3x8mm Button Head Screw ボタンヘッドスクリュー
x3
Cut off
(別売)(Not incld.)
M2x4mm Cap Head Screwキャップヘッドスクリュー
x2F060
F060
ロープロファイルタイプステアリングサーボ(別売)
Low-Profile Steering Servo (Not incld.)
Available steering servo size搭載可能なステアリングサーボサイズ
6
10
F0054.3mm Ball Joint
ボールジョイント
F005
F019M3x8mm Flat Head Screw フラットヘッドスクリュー
M3x8mm Flat Head Screw フラットヘッドスクリュー
x2
F019Alu Turnbuckle M3x33mmアルミターンバックル
x1
57.5mm
7
11
F005
F005
F020
57.8mm
F020Alu Turnbuckle M3x36mmアルミターンバックル
x2 x28
12
SMJ1146DOUBLE-SIDED TAPE両面テープ
Antennaアンテナ線
R80333mm ANTENNA PIPE & CAP3mmアンテナパイプ&キャップ
受信機(別売)Receiver (Not incld.)
9
13
SMJ1146DOUBLE-SIDED TAPE両面テープ
スピードコントローラー(別売)Speed Controller (Not incld.)
10
14
M3x6mm Button Head Screwボタンヘッドスクリュー
M3x8mm Button Head Screwボタンヘッドスクリュー
F048Body Postボディポスト
F001
M3x8mm Button Head Screwボタンヘッドスクリュー
F004
M3x6mm Button Head Screwボタンヘッドスクリュー
x3
M3x8mm Button Head Screwボタンヘッドスクリュー
x3
11
15
CM-A004-03Shim 3x5x0.3mmシム
F003Eccentric Bushing Set (IF11)エキセントリックブッシュセット(IF11)
0.5°
1.0°
1.5°
2.0°
These eccentric bushings adjust the front Camber.エキセントリックブッシュを用いてフロントキャンバーを調整することが可能です。
INITIAL SETTING初期設定
M3x10mm Button Head Screw ボタンヘッドスクリュー
M3x10mm Button Head Screw ボタンヘッドスクリュー
x4
Assemble both L&R.左右作る。L/R
RL
CAMBER ADJUSTMENTキャンバー調整12
16
F003
F003
F003
3°
6°
9°
12°
INITIAL SETTING初期設定
M3x8mm Button Head Screw ボタンヘッドスクリュー
M3x8mm Button Head Screw ボタンヘッドスクリューx1 RL
These eccentric bushings adjust the front Caster.エキセントリックブッシュを用いてフロントキャスターを調整することが可能です。
CASTER ADJUSTMENTキャスター調整13
17
1
2
F001
M3x10mm Button Head Screw ボタンヘッドスクリュー
M3x10mm Button Head Screw ボタンヘッドスクリュー
x2
M3x15mm Button Head Screw ボタンヘッドスクリュー
M3x15mm Button Head Screw ボタンヘッドスクリュー
x2
M2x5mm Button Head Screw ボタンヘッドスクリュー
x2G108
G10814
18
F006
F015Front Axleフロントアクスル
F014Steering Knuckle, Leftステアリングナックル、左
M3x8mm Button Head Screw ボタンヘッドスクリュー
M3x8mm Button Head Screw ボタンヘッドスクリュー
x1
M3x6mm Flat Head Screw フラットヘッドスクリュー
M3x6mm Flat Head Screw フラットヘッドスクリュー
x4
F006Alu Ball End 4.3x10mmアルミボールエンド
x2
Top
Bottom
Assemble both L&R.左右作る。L/R
R
L
NOTE DIRECTION向きに注意してください。
NOTE ORIENTATION位置を合わせてください。
15
16
19
F016
F017
F051
F056Front Spring 3.3 (0.5x6.6mm/5coils)フロントスプリング3.3(0.5x6.6mm/5 巻)
F051
x2
F017 x6
F017 x1
M3x4mm Set Screw セットスクリュー
M3x4mm Set Screw セットスクリュー
x2
F051E-Ring E2.5Eリング
x4
F016King Pinキングピン
x2
F017King Pin Shim 3x0.4mmキングピンシム
x18
キングピンを最も低い位置へ押し下げてから、M3x4mmセットスクリューを締め込みます。
Insert the kingpin, then tighten the M3x4mm set screw.
17
20
BAG CF036
F046Graphite Rear Wing Mount Plateカーボンリアウイングマウントプレート
F023Alu Rear Bulkheadアルミリアバルクヘッド
F023F042Graphite Lower Pod Plateカーボンロアポッドプレート
M3x6mm Button Head Screw ボタンヘッドスクリュー
M3x6mm Button Head Screw ボタンヘッドスクリュー
M3x6mm Button Head Screw ボタンヘッドスクリュー
x6
M3x6mm Flat Head Screw フラットヘッドスクリュー
M3x6mm Flat Head Screw フラットヘッドスクリュー
M3x6mm Flat Head Screw フラットヘッドスクリュー
x4
F036Alu Rear Wing Postアルミリアウイングポスト
x2
NOTE DIRECTION向きに注意してください。
18
21
F013Pivot Braceピボットブレース
F009
F049
F049M3 Nylon Nut Thin Typeナイロンナット薄型
x2
M3x10mm Flat Head Screw フラットヘッドスクリュー
x2
F009Alu 5mm Pivot Ballアルミ5mmピボットボール
x1
NOTE ORIENTATION位置を合わせてください。
Do not tighten fully.仮締め
F013
ネジの締めすぎに注意。5mmピボットボールがスムーズに動くように調整してください。
Do not tighten fully,5mm pivot balls must rotate freely.
x2
M2.5x5mm Button Head Screw ボタンヘッドスクリュー
F062
F062
M3x10mm Flat Head Screw フラットヘッドスクリュー
19
22
1
2
1
2
F009
F009
F013Pod Linkポッドリンク
M3x6mm Flat Head Screw フラットヘッドスクリュー
M3x6mm Flat Head Screw フラットヘッドスクリュー
x1
F009Alu 5mm Pivot Ballアルミ5mmピボットボール
x4
ネジの締めすぎに注意。5mmピボットボールがスムーズに動くように調整してください。
Do not tighten fully,5mm pivot balls must rotate freely.
M2x8mm Button Head Screw ボタンヘッドスクリュー
x4F061
F061
F061
x2
20
21
23
M3x6mm Flat Head Screw フラットヘッドスクリュー
M3x6mm Flat Head Screw フラットヘッドスクリュー
x4
Tighten fully.本締め
リアポッドがスムーズに動くことを確認します。もし、スムーズに動かない場合は、ピボットブレースのナットを緩め、再度ゆっくり締め直します。
Ensure free, smooth movement. If the pod plate does not move freely, loosen the nuts of composite pivot brace and tighten again.
22
24
BAG D
2.0mm
F044Graphite Chassis Braceカーボンシャーシブレース
F021
F062
F057Side Spring Medium (0.5mm/5.75coils)サイドスプリングミディアム(0.5mm/5.75 巻)
F008
M2.5x5mm Button Head Screw ボタンヘッドスクリュー
x2
M3x8mm Set Screw セットスクリュー
M3x8mm Set Screw セットスクリュー
x2
F008Alu Ball End M2.5x4.3mmアルミボールエンド
x2
F021Alu Side Spring Retainerアルミサイドスプリングリテーナー
x2
INITIAL POSITION初期位置
F062
23
25
F037
F037
M3x6mm Button Head Screw ボタンヘッドスクリュー
M3x6mm Button Head Screw ボタンヘッドスクリュー
x2
M3x6mm Flat Head Screw フラットヘッドスクリュー
M3x6mm Flat Head Screw フラットヘッドスクリュー
x2
F037Alu Standoff 12.8mmアルミポスト
x2
24
26
Washer M3ワッシャー
F022
F007
F049
F049M3 Nylon Nut Thin Type ナイロンナット薄型
x2
M3x6mm Button Head Screw ボタンヘッドスクリュー
M3x6mm Button Head Screw ボタンヘッドスクリュー
M3x6mm Button Head Screw ボタンヘッドスクリュー
x3
Washer M3ワッシャー
x1
F007Alu Ball End 4.3x11.8mmアルミボールエンド
x2
F022Alu Center Damper M3 NutアルミセンターダンパーナットM3
x1
F043Graphite Upper Pod Plateカーボンアッパーポッドプレート
INITIAL POSITION初期位置
25
27
F035Side Damper Setサイドダンパーセット
シリコンオイル(別売)Silicone Oil (Not incld.)
サイドダンパーチューブの溝にシリコンオイルを塗布します(#10,000 を推奨)
Add silicone oil (start from #10,000) in each slot of the side damper tubes.
M3x8mm Set Screw セットスクリュー
M3x8mm Set Screw セットスクリュー
x2
26
INITIAL POSITION初期位置
28
BAG E
LONG WHEELBASE
SHORT WHEELBASE
アルミアクスルハイトアジャスターの取り付ける向きを変えることで、2種類のホイールベースが選択可能です。ホイールベースの変化量は1.0mmです。
Wheelbase adjustment (forwards/backward +/-1.0mm) can be made by the orientation of the ride height adjuster.
F055
F055Flange Bearing 3/8X1/4フランジボールベアリング
x2
M3x6mm Button Head Screw ボタンヘッドスクリュー
M3x6mm Button Head Screw ボタンヘッドスクリュー
x4
F024Alu Axle Height Adjusterアルミアクスルハイトアジャスター
ロングホイールベース
ショートホイールベース
27
29
1 2
2
F025Diff Lightweight Rear Axleデフライトウェイトリアアクスル
F034
F034
F027Alu Wheel Hub, Leftアルミホイールハブ、レフト
M3x8mm Button Head Screw ボタンヘッドスクリュー
M3x8mm Button Head Screw ボタンヘッドスクリュー
x2
F034Axle Collar 1.0mmアクスルカラー
x1
F034Axle Collar 2.0mmアクスルカラー
x1
ホイールハブを取り付ける際に、横方向に若干のすき間(0.2mm程度)を設けてください。
The axle must have a small amount of side play. (approx. 0.2mm)
28
30
NOTE ORIENTATION向きに注意。
5.0mm 5.2mm
F055
F054
F026Alu Diff Hubアルミデフハブ F033
R0208Thrust Bearing SP 5mm5mmスラストベアリングSP
F030
F029
F032
F054
F0304mm Belleville Washerスプリングワッシャー
F050
F050M4 Nylon Nutナイロンナット
x1
F054Ball Bearing 3/8X1/4ボールベアリング
x2
F055Flange Bearing 3/8X1/4フランジボールベアリング
x1
F029Diff Ringデフリング
F033Alu Diff Thrust Bearing Wahserアルミデフスラストベアリングワッシャー
x1
F0321/8" Diff Ball1/8" インチデフボール
x18
ボールデフグリス(別売)Ball Diff Grease (Not incld.)
内側Inside
13
2
4
M4ナイロンナットの締め込み量で、ボールデフの効きを調整します。ボールデフが滑らないところまで、M4ナイロンナットを締め込みます。締め込み過ぎはデフの破損に繋がりますので、注意してください。
The M4 nylon nut is to adjust the tension of the rear differential. Tighten the M4 nylon nut gently until the differential doesn't slip under acceleration. Be careful not to over tighten as you may damage the diff balls and drive rings.
5
F052Pin 2x14mmピン
x1
M3x4mm Set Screw セットスクリュー
x1
F052
F028Alu Wheel Lockアルミホイールロック
F028
しっかり締めるTighten fully
グラファイトグリス(別売)
Graphite Grease (Not incld.)
29
31
BAG F
9.8mm
シリコンショックオイル(別売)Silicone Shock Oil (Not incld.)
シリコンショックオイル(別売)Silicone Shock Oil (Not incld.)
R0134Shock Caseショックケース
R0131AR0135
R0132
R0131Shock Lower Capショックロアキャップ
R0143
R0134Shock Spring Adjuster O-Ring SetショックスプリングアジャスターOリングセット
T080
R0024Ball End S 5.8mmボールエンドS
R0137BShock Shaft 30mmショックシャフト
T080Aluminum Washer 3x6x2.0mmアルミスペーサー
x1
R0137B
R0137BM2.6 Nylon Nut ナイロンナット
x1
R0143Shock Piston (Φ1.1x2hole)ショックピストン2 穴1.1φ
x1
R0137BWasher 2.6mmワッシャー
x1
R0135Shock O-Ring WhiteショックOリングホワイト
x2
R0132Shock Bushingショックブッシュ
x1
R0131AShock Lower O-RingショックロアOリング
x1
SHOCK LENGTH
R0137B
30
32
ショックシャフトを上下させ、オイルに混ざった空気をしっかり抜きます。
Move the shock shaft up and down to let the air bubbles escape from the oil.
R0141Diaphragm (Shock Bladder) ダイヤフラム
R0130Shock Capショックキャップ
R0144Shock Plastic Partsショックプラパーツ
R0144
F058Center Spring 1.2 (1.2x28mm/8coils)センタースプリング1.2(1.2x28mm/8 巻)
T052
T052
F052Alu Flange Ball 5.8mmアルミフランジボール
x2
シリコンショックオイル(別売)
Silicone Shock Oil (Not incld.)
31
33
32
34
Washer M3ワッシャー
M3x8mm Button Head Screw ボタンヘッドスクリュー
M3x8mm Button Head Screw ボタンヘッドスクリュー
x2
Washer M3ワッシャー
x2
モーター(別売)Motor (Not incld.)
ピニオンギヤ(別売)Pinion Gear (Not incld.)
33
35
センターショックを取り外します。
センターショックを取り付けます。
1
2
3
4
F038Battery Holder O-RingバッテリーホルダーOリング
Remove the center shock.
Install the center shock.
リポバッテリー(別売)LiPo Battery (Not incld.)
34
36
13
2
F048Body Postボディポスト
M3x8mm Button Head Screw ボタンヘッドスクリュー
M3x8mm Button Head Screw ボタンヘッドスクリュー
x1
M4x16mm Button Head Screw ボタンヘッドスクリュー
M4x16mm Button Head Screw ボタンヘッドスクリュー
x2
フロントウイング(別売)Front Wing (Not incld.)
35
37
M3x6mm Button Head Screw ボタンヘッドスクリュー
M3x6mm Button Head Screw ボタンヘッドスクリュー
x2
リアウイング(別売)Rear Wing (Not incld.)
36
38
F053
F053
F050
F050
F050M4 Nylon Nut ナイロンナット
x4
F053Ball Bearing 5X10x4mm (Rubber Shield)ボールベアリング(ラバーシールド)
x4
フロントタイヤ、インサート及びホイール(別売)
Front Tire, Insert and Wheel (Not incld.)
リアタイヤ、インサート及びホイール(別売)
Rear Tire, Insert and Wheel (Not incld.)
37
A new le gend be gins
9966-001
Creation Model Ltd. 3-23-15 Kamijima, Naka-ku, Hamamatsu-shi, Shizuoka-ken, 433-8122 Japan
株式会社クリエーションモデル〒 433-8122静岡県浜松市中区上島 3-23-15Email:[email protected]