INSTRUCTION FOR ASSEMBLY
120x180 h Traditional sauna cabin
1. SAUNA PLAN
TOOLS REQUIRED: Hammer or pin nailer
Drill or cordless screwdriver
Tape measure
Square
Level
Handsaw
815
120x180 h TRADITIONAL SAUNACABINView from the top
291
120
0
1800
690
HEATER
SAWO MN-36NS
208x340mm
541
286
UPPER BENCH
LOWER BENCH
508
308
120
0
Control Unit
1115
2. BASE FRAME
There are 4 details for the base frame. Fasten the three corners together with the screws (4,0x30 mm).
Cross-measure from the corners to check that they are at straight angle. Correct the corners if necessary
and screw the last screw in. Check that the base frame is level using a spirit level.
BASE FRAME
DETAIL NR.1
DETAIL NR.2
DETAIL NR.3 DETAIL NR.3
152 250 1368
1770
11
70
1770
11
70
3. WALL ELEMENTS
WALL ELEMENTS B1 & B2
WALL ELEMENT E1
WA
LL E
LE
ME
NT
A1
750
800
1800
1686
WALL ELEMENTS1128
1185
WA
LL E
LE
ME
NT
C1
1128
1185
WALL ELEMENT D1
226
276
690
INTERIOR (Alternate):
There are 2 methods for fastening Your sauna wall elements:
EXTERIOR (standard):
4. CEILING ELEMENTS
Make sure that the ceiling elements fit on the top of the wall elements. Check also, that the tongue and
groove joints between ceiling elements are fastened properly to each other. You may need to lift the
elements a little at the joints to make them slide together. You may fix the ceiling elements with screws
(5,0x80 mm) also, if You think that is necessary.
CEILING ELEMENT 1 CEILING ELEMENT 2
Ventilation
876 924
120
0
120
0
5. DOOR
6. ELECTRICAL EQUIPMENT
Always use a certified electrician for any electrical work. Before installing heater and control unit follow
the manufacturer directions. This will prevent injury to you and the product. You may need to install the
control unit into a wall element. The sauna light should be installed under the bench. Use the silicone
cable for the sauna light.
Your sauna contains a high quality sauna door. Be careful when handling the door as the glass may break
if it is hit with a sharp object. At no time should the edge of the glass touch a hard floor or wall surface.
The door element is the last wall element. The door is fastened with screws (5,0x80 mm). There is sauna
door handle in your sauna kit. Cover the exposed holes with wooden covers. The door always opens out.
If it is necessary to change hanging, move the top rail to the other end. Put the door on the floor, unscrew
the upper plank's four screws, put the plank on the opposite side of the door and screw it up with the
same four screws.
For making the door move easily, regulate the roller-lock when needed. Also you can regulate
the door handle a bit.
7. BENCHES
cross-cut length
Bench support details: upper bench 28x42 730 5 pcs
lower bench 28x42 280 4 pcs
*There is one extra support detail (28x42x1000 mm) to support benches from the middle.
1. STEP : Fixing bench support
32
715
45
CROSS-CUT OF THE BENCHES
LOWER BENCH
280
435
788
508
730
UPPER BENCH
308
508
BENCH SKIRT
368
45
0
81
8
268
352
2. STEP : Fixing bench frames (screws 5,0x70 mm)
3. STEP : Fit in bench grid
8. BACKREST
9. HEATER GUARD
10. FLOOR GRID
After placing the benches, place the back grid. There are predrilled holes. Fasten the back grid using
screws (4,0x45 mm) and cover the screw holes with wooden covers.
Next step is the installation the floor grids. In your sauna, there is one floor grid with measures 470x680
mm. You do not need to it them with screws.
Place the heater guard around the heater. Use screws (5,0x70 mm) for fastening the heater guard to the
wall.
11. MOLDINGS
Fasten them with nails.
cross-cut length
Door moldings 12x42 1930 4 pcs.
Corner moldings 28x45 1930 4 pcs.
12. UPPER FRAME
Mount the upper frame on the floor and then lift it to the top of the sauna and fasten it to the ceiling
element using screws (4,0x30 mm) and metal angles
To give a finished appearance Your sauna install door and corner moldings.
UPPER FRAME
ECCENTRIC
1859
EC
CENTR
ICE
CCENTR
IC
12
59
ECCENTRIC
1859
ECCENTRIC
EC
CENTR
ICE
CCENTR
IC
12
59
ECCENTRIC
10